View ADP3302_21209.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

a
FEATURES High Accuracy: 0.8% Ultralow Dropout Voltage: 120 mV @ 100 mA Typical Requires only CO = 0.47 F for Stability anyCAPTM = Stable with All Types of Capacitors Current and Thermal Limiting Low Noise Dropout Detector Multiple Voltage Options Thermally Enhanced SO-8 Package APPLICATIONS Cellular Telephones Notebook and Palmtop Computers Battery Powered Systems Portable Instruments High Efficiency Linear Regulators
High Precision anyCAPTM Dual Low Dropout Linear Regulator ADP3302
FUNCTIONAL BLOCK DIAGRAM (1/2 IS SHOWN)
ADP3302
OUT CC R1 IN THERMAL PROTECTION Q2 SD BANDGAP REF GND DRIVER Q1
ERR
GM R2
EOUT
2
GENERAL DESCRIPTION
330k VOUT1 0.47F
The ADP3302 is a member of the ADP330X family of precision micropower low dropout anyCAPTM regulators. The ADP3302 contains two fully independent 100 mA regulators with separate shutdown and merged error outputs. It features 1.4% overall output accuracy and very low, 120 mV typical, dropout voltage. The ADP3302 has a wide input voltage range from 3 V to 12 V. It features an error flag that signals when either of the two regulators is about to lose regulation. It has short circuit current protection as well as thermal shutdown. The ADP3302's enhanced lead frame design allows for a maximum power dissipation of 630 mW @ +70C ambient temperature and 1.0 W at room temperature without any external heat sink.
anyCAPTM is a trademark of Analog Devices, Inc.
VIN 0.47F
ERR
5 8
IN IN
OUT1 1
ADP3302
3 GND
OUT2 4 SD2
6
VOUT2 0.47F
SD1
7
ON OFF
Figure 1. Application Circuit
REV. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 617/329-4700 World Wide Web Site: http://www.analog.com Fax: 617/326-8703 (c) Analog Devices, Inc., 1997
ADP3302-SPECIFICATIONS noted)
Parameter GROUND CURRENT GROUND CURRENT IN DROPOUT DROPOUT VOLTAGE Symbol IGND IGND VDROP
(@ TA = -20 C to +85 C, VIN = 7 V, CIN = 0.47 F, COUT = 0.47 F, unless otherwise
1
Conditions IL1 = IL2 = 100 mA IL1 = IL2 = 0.1 mA VIN = 2.5 V IL1 = IL2 = 0.1 mA VOUT 98% of VO, Nominal IL = 100 mA IL = 10 mA IL = 1 mA ON OFF 0 < VSD < 5 V 5 VSD 12 V, @ VIN = 12 V VSDI = VSD2 = 0, TA = +25C, @ VIN =12 V VSDI = VSD2 = 0, TA = +85C, @ VIN =12 V TA = +85C, @ VIN = 12 V TA = +25C, @ VIN = 12 V VEO = 5 V ISINK = 400 A VIN = Nominal VOUT +1 V VIN = 12 V, IL = 100 mA T = 10 ms f = 10 Hz-100 kHz, @ TA = +25C VOUT = 3.3 V VOUT = 5 V
Min
Typ 2 0.4 1.0
Max 4 0.8 2
Units mA mA mA
0.12 0.05 0.02 2.0 0.9 0.9 0
0.2 0.1 0.05 0.3 1 22 1 5 12 2 13
V V V V V A A A A A A A V mA %/W
SHUTDOWN THRESHOLD SHUTDOWN PIN INPUT CURRENT GROUND CURRENT IN SHUTDOWN MODE
VTHSD ISDIN IQ
0
OUTPUT CURRENT IN SHUTDOWN MODE ERROR PIN OUTPUT LEAKAGE ERROR PIN OUTPUT "LOW" VOLTAGE PEAK LOAD CURRENT THERMAL REGULATION OUTPUT NOISE
IOSD IEL VEOL ILDPK
VO VO
0.15 200 0.05
0.3
VNOISE
75 110
V rms V rms
NOTES 1 Ambient temperature of
85C corresponds to a typical junction temperature of +125C.
Specifications subject to change without notice.
ADP3302-3.0-SPECIFICATIONS (@ T = -20 C to +85 C, V = 3.3 V, C = 0.47 otherwise noted)
A IN IN
F, COUT = 0.47 F, unless
Typ 3 Max 3.024 Units V
Parameter OUTPUT VOLTAGE
Symbol VOUT1 or VOUT2
Conditions VIN = 3.3 V to 12 V IL = 0.1 mA to 100 mA TA= +25C VIN = 3.3 V to 12 V IL = 0.1 mA to 100 mA VIN = 3.3 V to 12 V TA = +25C, IL = 0.1 mA IL = 0.1 mA to 100 mA TA = +25C IL = 0.1 mA to 100 mA TA = +25C
Min 2.976
2.958
3 0.024 0.030 1
3.042
V mV/V mV/mA V/mA
LINE REGULATION LOAD REGULATION CROSS REGULATION
VO V IN VO I L V 01 I L2 V 02 or I L1
Specifications subject to change without notice.
-2-
REV. 0
ADP3302
ADP3302-3.2-SPECIFICATIONS
Parameter OUTPUT VOLTAGE Symbol VOUT1 or VOUT2
(@ TA = -20 C to +85 C, VIN = 3.5 V, CIN = 0.47 F, COUT = 0.47 F, unless otherwise noted)
Min 3.174 Typ 3.2 Max 3.226 Units V
Conditions VIN = 3.5 V to 12 V IL = 0.1 mA to 100 mA TA= +25C VIN = 3.5 V to 12 V IL = 0.1 mA to 100 mA VIN = 3.5 V to 12 V TA = +25C, IL = 0.1 mA IL = 0.1 mA to 100 mA TA = +25C IL = 0.1 mA to 100 mA TA = +25C
3.155
3.2 0.026 0.032 1
3.245
V mV/V mV/mA V/mA
LINE REGULATION LOAD REGULATION CROSS REGULATION
VO V IN
VO I L V 01 I L2
or
Specifications subject to change without notice.
V 02 I L1
ADP3302-3.3-SPECIFICATIONS (@ T = -20 C to +85 C, V = 3.6 V, C = 0.47 otherwise noted)
A IN IN
F, COUT = 0.47 F, unless
Typ 3.3 Max 3.327 Units V
Parameter OUTPUT VOLTAGE
Symbol VOUT1 or VOUT2
Conditions VIN = 3.6 V to 12 V IL = 0.1 mA to 100 mA TA= +25C VIN = 3.6 V to 12 V IL = 0.1 mA to 100 mA VIN = 3.6 V to 12 V TA = +25C, IL = 0.1 mA IL = 0.1 mA to 100 mA TA = +25C IL = 0.1 mA to 100 mA TA = +25C
Min 3.273
3.253
3.3 0.026 0.033 1
3.347
V mV/V mV/mA V/mA
LINE REGULATION LOAD REGULATION CROSS REGULATION
VO V IN
VO I L
V 01 I L2 V 02 or I L1
Specifications subject to change without notice.
ADP3302-5.0-SPECIFICATIONS (@ T = -20 C to +85 C, V = 5.3 V, C = 0.47 otherwise noted)
A IN IN
F, COUT = 0.47 F, unless
Typ 5.0 Max 5.040 Units V
Parameter OUTPUT VOLTAGE
Symbol VOUT1 or VOUT2
Conditions VIN = 5.3 V to 12 V IL = 0.1 mA to 100 mA TA= +25C VIN = 5.3 V to 12 V IL = 0.1 mA to 100 mA VIN = 5.3 V to 12 V TA = +25C, IL = 0.1 mA IL = 0.1 mA to 100 mA TA = +25C IL = 0.1 mA to 100 mA TA = +25C
Min 4.960
4.930
5.0 0.04 0.05 1
5.070
V mV/V mV/mA V/mA
LINE REGULATION LOAD REGULATION CROSS REGULATION
VO V IN
VO I L
V 01 I L2
or V 02
I L1
Specifications subject to change without notice.
REV. 0
-3-
ADP3302
ABSOLUTE MAXIMUM RATINGS* PIN FUNCTION DESCRIPTIONS
Input Supply Voltage . . . . . . . . . . . . . . . . . . . . -0.3 V to +16 V Please note: Pins 5 and 8 should be connected externally for proper operation. Shutdown Input Voltage . . . . . . . . . . . . . . . . . -0.3 V to +16 V Error Flag Output Voltage . . . . . . . . . . . . . . . . -0.3 V to +16 V Power Dissipation . . . . . . . . . . . . . . . . . . . . Internally Limited Operating Ambient Temperature Range . . . . -55C to +125C Operating Junction Temperature Range . . . . -55C to +125C JA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96C/W JC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55C/W Storage Temperature Range . . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300C Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . . . +215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . +220C
*This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operation section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Pin 1
Name OUT1
Function Output of Regulator 1, fixed 3.0 V, 3.2 V, 3.3 V or 5 V output voltage. Sources up to 200 mA. Bypass to ground with a 0.47 F capacitor. Open Collector Output. Active low indicates that one of the two outputs is about to go out of regulation. Ground Pin. Output Regulator 2. Independent of Regulator 1. Fixed 3.0 V, 3.2 V, 3.3 V or 5 V output voltage. Bypass to ground with a 0.47 F capacitor. Regulator Input. Supply voltage can range from 3.0 V to 12 V. Pins 5 and 8 must be connected together for proper operation. Active Low Shutdown Pin for Regulator 2. Connect to ground to disable the Out 2 output. When shutdown is not used, this pin should be connected to the input pin. Shutdown Pin for Regulator 1, otherwise identical to SD2.
PIN CONFIGURATION
2
ERR
3 4
GND OUT2
5, 8
IN
ORDERING GUIDE
6 Package Option*
SD2
Model ADP3302AR1 ADP3302AR2 ADP3302AR3 ADP3302AR4 ADP3302AR5
Voltage Outputs OUT 1 OUT 2 OUT 1 OUT 2 OUT 1 OUT 2 OUT 1 OUT 2 OUT 1 OUT 2 3.0 V 3.0 V 3.2 V 3.2 V 3.3 V 3.3 V 3.3 V 5.0 V 5.0 V 5.0 V
SO-8 SO-8 SO-8 SO-8 SO-8 SO-8 SO-8 SO-8 SO-8 SO-8
7
SD1
OUT 1 1 ERR 2
8
IN
ADP3302
7 SD1
TOP VIEW GND 3 (Not to Scale) 6 SD2 OUT 2 4 5 IN
NOTES *SO = Small Outline Package. Contact factory for availability of customized options available with mixed output voltages.
CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the ADP3302 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
-4-
REV. 0
Typical Performance Characteristics- ADP3302
5.001 IL = 0mA 5
OUTPUT VOLTAGE - Volts
OUTPUT VOLTAGE - Volts
5.005
1.6 1.4 GROUND CURRENT - mA
IL = 1mA 4.999 IL = 20mA
5.000 VIN = 7V 4.995
IL = IL2 =0 1.2 1.0 0.8 0.6 0.4 0.2
4.998
4.990
4.997 IL = 100mA 4.996
4.985
4.995 8 10 12 5.1 5.2 5.3 5.4 5.5 6 INPUT VOLTAGE - Volts
14 16
4.980
0.0 0 25 50 75 100 125 150 175 OUTPUT LOAD - mA 200
1
3
5 7 9 11 INPUT VOLTAGE - Volts
13
16
Figure 2. Line Regulation Output Voltage vs. Supply Voltage on ADP3302AR5
Figure 3. Output Voltage vs. Load Current Up to 200 mA on ADP3302AR5
Figure 4. Quiescent Current vs. Supply Voltage-ADP3302AR3
5 VIN = 7V GROUND CURRENT - mA
0.2
3000
IL1 = 0 TO 200mA IL2 = 0 TO 200mA 3
GROUND CURRENT - A
OUTPUT VOLTAGE - %
4
0.1
2500 IL1 = 100mA IL2 = 100mA
0.0 IL = 0 -0.1
2000
1500
2
-0.2
1000
IL1 = 100mA IL2 = 0mA
1 IL1 = 0 TO 200mA IL2 = 0mA 0 0 50 100 150 OUTPUT LOAD - mA 200
-0.3
500
IL1 = 0mA IL2 = 0mA
-0.4 -45 -25 -5
15 35 55 75 95 115 135 TEMPERATURE - C
0 -45 -25 -5
15
35
55
75
95 115 135
TEMPERATURE - C
Figure 5. Quiescent Current vs. Load Current
Figure 6. Output Voltage Variation % vs. Temperature
Figure 7. Quiescent Current vs. Temperature
250
5
8.0 VIN
INPUT/OUTPUT VOLTAGE - Volts
INPUT-OUTPUT VOLTAGE - mV
200
4
INPUT/OUTPUT VOLTAGE - Volts
7.0 6.0 5.0 4.0 3.0 2.0 1.0 0 0 20 40 60 VSD = VIN CL = 0.47F RL = 33 80 100 120 140 160 180 200 TIME - s VOUT
150
3
100
2 RL = 33 1
50
0 0 20 40 60 80 100 120 140 160 180 200 OUTPUT LOAD - mA
0
0
1
2 4 3 2 3 INPUT VOLTAGE - Volts
1
0
Figure 8. Dropout Voltage vs. Output Current
Figure 9. Power-Up/Power-Down on ADP3302AR3. SD = 3 V or VIN
Figure 10. Power-Up Transient on ADP3302AR1
REV. 0
-5-
ADP3302 -Typical Performance Characteristics
3.31 3.3 3.3k, 0.47F LOAD 3.29 3.31 3.3 33, 0.47F LOAD 3.29 7.5 VIN 7 0 40 80 120 160 200 240 280 320 360 400 TIME - s
3.29 7.5 mA VIN 7 0 40 80 120 160 200 240 280 320 360 400 TIME - s 3.29 3.31 3.31 3.3 3.3k, 10F LOAD
3.305
Volts
3.3 VOUT1 CL = 0.47F
3.295
Volts
Volts
5.002
Volts 3.3 33, 10F LOAD
VOUT2 5 4.998 I (VOUT1) 100mA 100 0 0 200 400 600 TIME - s 800 1000
Figure 11. Line Transient Response-- (0.47 F Load) on ADP3302AR4
Figure 12. Line Transient Response (10 F Load) on ADP3302AR4
Figure 13. Load Transient on VOUT1 and Crosstalk of VOUT2 on ADP3302AR4 for 1 mA to 100 mA Pulse
5
3.302
Volts
Volts
3.3 CL = 10F 5.03 5.01
VOUT1
3.5 0 400 3.3V Volts
4 3 CL = 0.47F
RL = 33
3.298
3.3V 2 CL = 4.7F 1 0
Volts
5 4.99 4.97
VOUT2
mA
300 200 Volts 100
5 0 3V 0 20 40 60 80 100 120 140 160 180 200 TIME - s
mA
100 0 0 200
I (VOUT2) 100mA
0
400 600 TIME - s
800
1000
0
1
2 3 TIME - sec
4
5
Figure 14. Load Transient on VOUT2 and Crosstalk on VOUT1 on ADP3302AR4 for 1 mA to 100 mA Pulse
Figure 15. Short Circuit Current
Figure 16. Turn On ADP3302AR3
VOLTAGE NOISE SPECTRAL DENSITY - V/ Hz
4 C = 0.47F R = 33 ON 3.3V OUTPUT 3
RIPPLE REJECTION - dB
0 -10 -20 -30 -40 -50 -60 -70 -80 -90 ac 100 1k 10k 100k FREQUENCY - Hz 1M 10M bd c a d a. 0.47F @ NO LOAD b. 0.47F @ 33 c. 10F @ NO LOAD d. 10F @ 33
0.8 c a 0.6 0.47F BYPASS PIN 5, 8 TO PIN 3
b
2
Volts
VOUT 1 0
0.4
bd
b 0.2 a. 0.47F @ NO LOAD b. 0.47F @ 33 c. 10F @ NO LOAD d. 10F @ 33 103 104 FREQUENCY = Hz d a c 105
5 VSD 0 0 5 10 15 20 25 30 35 40 45 TIME - s 50
-100 10
0 102
Figure 17. Turn Off on ADP3302AR3
Figure 18. Power Supply Ripple Rejection on ADP3302AR3
Figure 19. Output Noise Density on ADP3302AR5
-6-
REV. 0
ADP3302
APPLICATION INFORMATION anyCAPTM
To limit the maximum junction temperature to 125C, maximum ambient temperature must be lower than: TAMAX = 125C 43.6C = 81.4C
The ADP3302 is an easy to use dual low dropout voltage regulator. The ADP3302 requires only a very small 0.47 F bypass capacitor on the outputs for stability. Unlike the conventional LDO designs, the ADP3302 is stable with virtually any type of capacitors (anyCAPTM) independent of the capacitor's ESR (Effective Series Resistance) value.
Capacitor Selection
PRINTED CIRCUIT BOARD LAYOUT CONSIDERATION
All surface mount packages rely on the traces of the PC board to conduct heat away from the package. In standard packages the dominant component of the heat resistance path is the plastic between the die attach pad and the individual leads. In typical thermally enhanced packages one or more of the leads are fused to the die attach pad, significantly decreasing this component. However, to make the improvement meaningful, a significant copper area on the PCB has to be attached to these fused pins. The ADP3302's patented thermal coastline lead frame design uniformly minimizes the value of the dominant portion of the thermal resistance. It ensures that heat is conducted away by all pins of the package. This yields a very low 96C/W thermal resistance for an SO-8 package, without any special board layout requirements, relying just on the normal traces connected to the leads. The thermal resistance can be decreased by, approximately, an additional 10% by attaching a few square cm of copper area to the two VIN pins of the ADP3302 package. It is not recommended to use solder mask or silkscreen on the PCB traces adjacent to the ADP3302 pins since it will increase the junction to ambient thermal resistance of the package.
Shutdown Mode
Output Capacitors: As with any micropower device, output transient response is a function of the output capacitance. The ADP3302 is stable with a wide range of capacitor values, types and ESR (anyCAPTM). A capacitor as low as 0.47 F is all that is needed for stability. However, larger capacitors can be used if high output current surges are anticipated. The ADP3302 is stable with extremely low ESR capacitors (ESR 0), such as multilayer ceramic capacitors (MLCC) or OSCON. Input Bypass Capacitor: An input bypass capacitor is not required. However, for applications where the input source is high impedance or far from the input pins, a bypass capacitor is recommended. Connecting a 0.47 F capacitor from the input pins (Pins 5 and 8) to ground reduces the circuit's sensitivity to PC board layout. Low ESR capacitors offer better performance on a noisy supply; however, for less demanding requirements a standard tantalum or aluminum electrolytic capacitor is adequate.
Thermal Overload Protection
The ADP3302 is protected against damage due to excessive power dissipation by its thermal overload protection circuit, which limits the die temperature to a maximum of 165C. Under extreme conditions (i.e., high ambient temperature and power dissipation) where die temperature starts to rise above 165C, the output current is reduced until the die temperature has dropped to a safe level. The output current is restored when the die temperature is reduced. Current and thermal limit protections are intended to protect the device against accidental overload conditions. For normal operation, device power dissipation should be externally limited so that junction temperatures will not exceed 125C.
Calculating Junction Temperature
Applying a TTL high signal to the shutdown pin or tying it to the input pin will turn the output ON. Pulling the shutdown pin down to a TTL low signal or tying it to ground will turn the output OFF. Outputs are independently controlled. In shutdown mode, quiescent current is reduced to less than 2 A.
Error Flag Dropout Detector
The ADP3302 will maintain its output voltage over a wide range of load, input voltage and temperature conditions. If regulation is lost, for example, by reducing the supply voltage below the combined regulated output and dropout voltages, the ERRor flag will be activated. The ERR output is an open collector, which will be driven low. Once set, the ERRor flag's hysteresis will keep the output low until a small margin of operating range is restored, either by raising the supply voltage or reducing the load. A single ERR pin serves both regulators in the ADP3302 and indicates that one or both regulators are on the verge of losing regulation.
APPLICATION CIRCUIT Dual Post Regulator Circuit for Switching Regulators
Device power dissipation is calculated as follows: PD = (VIN - VOUT1) ILOAD1 + (VIN - VOUT2) ILOAD2 + (VIN) IGND Where ILOAD1 and ILOAD2 are Load currents on Outputs 1 and 2, IGND is ground current, VIN and VOUT are input and output voltages respectively. Assuming ILOAD1 = ILOAD2 = 100 mA, IGND = 2 mA, VIN = 7.2 V and VOUT1 = VOUT2 = 5.0 V, device power dissipation is: PD = (7.2 V - 5 V) 100 mA + (7.2 V - 5 V) 100 mA + (7.2 V) 2 mA = 0.454 W The proprietary thermal coastline lead frame used in the ADP3302 yields a thermal resistance of 96C/W, which is significantly lower than a standard 8-pin SOIC package at 170C/W. Junction temperature above ambient temperature will be approximately equal to: 0.454 W 96C/W = 43.6C
The ADP3302 can be used to implement a dual 3 V/100 mA post regulator power supply from a 1 cell Li-Ion input (Figure 20). This circuit takes 2.5 V to 4.2 V as the input and delivers dual 3 V/100 mA outputs. Figure 21 shows the typical efficiency curve. For ease of explanation, let's partition the circuit into the ADP3000 step-up regulator section and the ADP3302 low dropout regulation section. Furthermore, let's divide the operation of this application circuit into the following three phases.
REV. 0
-7-
ADP3302
2.5V 4.2V R1 100k C1 100F 10V AVX-TPS R3 1M R2 90k R4 120k ILIM SET VIN SW1 C2 33nF R7 90k R9 348k 1% R10 200k 1% R5 330k Q1 2N2907 R8 10k (SUMIDA-CDRH62) L1 6.6F IN5817 IN C3 100F 10V AVX-TPS IN VO2 1F 6V C4 (MLC) 1F C5 6V (MLC) 3V 100mA
R6 100k
ADP3000
AO GND SW2 FB
ADP3302
SD GND VO2
3V 100mA
Figure 20. Cell Li-Ion to 3 V/200 mA Converter with Shutdown at VIN < 2.5 V
Phase One: When the input voltage is equal to 3.7 V or higher, the ADP3000 is off and the ADP3302 operates on its own to regulate the output voltage. At this phase, current is flowing into the input pins of the ADP3302 via the inductor L1 and the Schottky diode. At the same time, the ADP3000 is set into sleep mode by pulling the FB pin (via R9 and R10 resistor divider network) to about 10% higher than its internal reference which is set to be 1.245 V. Phase Two: As the input voltage drops below 3.7 V, the decreasing input voltage causes the voltage of the FB pin to be within 5% of the 1.245 V reference. This triggers the ADP3000 to turn on, providing a 3.4 V regulated output to the inputs of the ADP3302. The ADP3000 continues to supply the 3.4 V regulated voltage to the ADP3302 until the input voltage drops below 2.5 V. Phase Three: When the input voltage drops below 2.5 V, the ADP3302 will shut down and the ADP3000 will go into sleep mode. With the input voltage below 2.5 V, the resistor divider network, R1 and R2, applies a voltage that is lower than the ADP3000's internal 1.245 V reference voltage to the SET pin. This causes the AO pin to have a voltage close to 0 V, which causes the ADP3302 to go into shutdown directly and Q1 to turn on and pull the FB pin 10% or higher than the internal 1.245 V reference voltage. With the FB pin pulled high, the ADP3000 goes into sleep mode.
80 IO = 50mA + 50mA AT VIN 2.5V SHDN IQ = 500A
Supply Sequencing Circuit
Figure 22 shows a simple and effective way to achieve sequencing of two different output voltages, 3.3 V and 5 V, in a mixed supply voltage system. In most cases, these systems need careful sequencing for the supplies to avoid latchup. At turn-on, D1 rapidly charges up C1 and enables the 5 V output. After a R2-C2 time constant delay, the 3.3 V output is enabled. At turn-off, D2 quickly discharges C2 and R3 pulls SD1 low, turning off the 3.3 V output first. After a R1-C1 time constant delay, the 5 V output turns off.
VIN = 6V TO 12V
8 2
C5 1F D2 C2 0.01F D1 C1 0.01F R1 220k
IN IN SD1
ERR OUT1 1 C3 0.5F VOUT1 3.3V
5
D3
7
3.3V ON/OFF
R3 330k
6
ADP3302
OUT2 4 SD2 GND
3
C4 0.5F
VOUT2 5.0V
R2 220k
Figure 22. Turn-On/Turn-Off Sequencing for Mixed Supply Voltages
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
% EFFICIENCY
75
8-Pin SOIC (SO-8)
IO = 100mA + 100mA
70 65 2.6 3.0
0.1968 (5.00) 0.1890 (4.80)
8 1 5 4
3.4
3.8
4.2
VIN (V)
0.1574 (4.00) 0.1497 (3.80)
0.2440 (6.20) 0.2284 (5.80)
Figure 21. Typical Efficiency of the Circuit of Figure 20
PIN 1 0.0098 (0.25) 0.0040 (0.10)
Refer to Figure 20. R9 and R10 set the output voltage of the ADP3000. R1, R2, and R3 set the shutdown threshold voltage for the circuit. For further details on the ADP3000, please refer to the ADP3000 data sheet.
0.0688 (1.75) 0.0532 (1.35)
0.0196 (0.50) x 45 0.0099 (0.25)
SEATING PLANE
0.0500 0.0192 (0.49) (1.27) 0.0138 (0.35) BSC
0.0098 (0.25) 0.0075 (0.19)
8 0
0.0500 (1.27) 0.0160 (0.41)
-8-
REV. 0
PRINTED IN U.S.A.
C2989-12-1/97

▲Up To Search▲

Price & Availability of ADP3302

	To Download ADP3302 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .