 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| INTEGRATED CIRCUITS DATA SHEET TDA8349A Multistandard IF amplifier and demodulator Product specification File under Integrated Circuits, IC02 February 1991 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator GENERAL DESCRIPTION TDA8349A The TDA8349A is a multistandard IF amplifier and demodulator with AGC and AFC functions for television receivers. The device has a video recognition circuit and a video switch for internal or external video for full SCART applications. FEATURES * Full-range gain-controlled wideband IF amplifier up to 60 MHz * Wide-band video amplifier with good linearity and a class AB output stage to ensure a very low output impedance * Supply independent video output level * Small second harmonic IF output * AGC circuit which operates on top sync level (negative modulation) or on white level (positive modulation) or on top level (MAC) with reduced sensitivity for high sound carriers * AFC circuit with an internal 90 phase shift circuit, a sample-and-hold circuit for negatively modulated signals to reduce video dependent AFC information and an analog or digital output * Video recognition possibility based on horizontal pulse duty cycles * Video switch for selection of internal or external video signals * Wide supply voltage range and ripple rejection * Requires few external components * Tuner AGC output for npn and pnp tuners QUICK REFERENCE DATA SYMBOL V14-17 I14 V1-2(RMS) Gv V11-17(p-p) S/N V8-17(p-p) PARAMETER supply voltage (pin 14) supply current (pin 14) IF input sensitivity (RMS value) IF gain control range video output voltage (peakto-peak value) signal-to-noise ratio AFC output voltage swing (peak-to-peak value) Vi = 10 mV Vi = 10 mV CONDITIONS MIN. 10.2 40 - 66 1.7 54 10 TYP. 12 55 50 72 1.9 61 - MAX. 13.2 65 80 - 2.1 - 11 V mA V dB V dB V UNIT ORDERING AND PACKAGE INFORMATION EXTENDED TYPE NUMBER TDA8349A Note 1. SOT146-1; 1996 November 29. PACKAGE PINS 20 PIN POSITION DIL MATERIAL plastic CODE SOT146(1) February 1991 2 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A February 1991 3 Fig.1 Block diagram. Philips Semiconductors Product specification Multistandard IF amplifier and demodulator PINNING PIN 1,2 3 4 5 6 7 8 9 10 11 12 13 14 15,16 17 18 19 20 balanced IF inputs tuner AGC starting point adjustment tuner AGC output AGC time constant AFC on/off switch and sample-and-hold capacitor video switch AFC output Q1 AFC output Q2 video switch external input video output video switch internal input video switch output positive supply voltage reference tuned circuit for demodulator ground mute output coincidence filter system switch DESCRIPTION TDA8349A FUNCTIONAL DESCRIPTION General The IC consists of the following parts as illustrated in Fig.1: * Gain controlled video IF amplifier * Quasi-synchronous demodulator * Video amplifier/buffer with white spot clamp/inverter and noise clamp * AGC circuit which operates either on top sync level (negative modulation) or on white level (positive modulation) or on top level (MAC) * AFC circuit with sample-and-hold circuit for negatively modulated signals, on/off switch and a digital or analog output (switchable) * Circuit for switching between positive and negative modulation * Video recognition circuit for sound muting and tuning indication * Video switch which facilitates selection between two different video signals, with different gain settings IF amplifier The IF amplifier consists of three AC coupled differential gain stages with adjustable feedback in the emitter. The AC coupling allows simple biasing, cascades can be used and no DC feedback is required. This provides a control range above 70 dB with good linearity. The minimum input signal to obtain the nominal output amplitude is 50 V RMS. Demodulator The demodulator is a quasi-synchronous circuit that employs passive carrier regeneration and a tuned circuit for selectivity. The regenerated carrier signal is limited by a clamping circuit before it is fed to the demodulator. Switching between positive and negative modulation is achieved by the system switch which provides currents to the demodulator in a positive or negative direction. Video amplifier The video amplifier based on the feedback principle improves the linearity of the video output buffer. It has an internal bandgap reference to ensure a stable video output at different supply voltages and temperatures. This 4 February 1991 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator bandgap also reduces the supply ripple on the video output to values less than -30 dB. The video amplifier has a typical bandwidth of 10 MHz which allows application for all new video standards with bandwidths of up to 10 to 12 MHz. The video output signal has an amplitude of 2 V (p-p). White spot protection comprises a white spot clamp system combined with a delayed-action inverter which is also highly resistant to high sound carriers. A switchable DC shift for positively modulated IF signals ensures correct signal handling. This switching is obtained via pin 20, which is the same pin used for switching the demodulation polarity in the demodulator. The circuit also has a noise clamp which prevents the video output becoming less than 400 mV below the top sync level at noise peaks. The output buffer of the video amplifier consists of a class A/B circuit which can handle large source as well as large sink currents. This makes the circuit more flexible in several applications with one or more ceramic filters connected to this output buffer. AGC control circuit This converts the AGC detector voltage (pin 5) into a current signal which controls the gain of the IF amplifier. It also provides a tuner AGC control output from pin 4, The chosen AGC currents: MODE B/G L MAC(positive) MAC(negative) Note UNLOAD CURRENT 50 A 500 nA (note 1) 200 nA 500 nA LOAD CURRENT 1.5 mA 1.5 mA 1.5 mA 1.5 mA TDA8349A current limiting is incorporated to prevent internal damage. The AGC starting point is adjusted by a voltage between 3 and 5 V for pnp tuners and between 7 and 9 V for npn tuners via pin 3. AGC circuit A new AGC system has been designed for the AGC. It will be a top sync-detector for negatively modulated signals and a top white level AGC for positively modulated signals. For optimal flexibility reasons the load and unload currents of the AGC are chosen such that both, a relatively fast set, as well as a set with a low tilt are possible for positive (L) and negative (B/G) modulated signals. For this reason a tilt ratio between positive (L) and negative (B/G) of approximately 3:1 has been chosen. This means that in a fast set the choice of a typical tilt for negatively modulated signals of 2% will obtain a typical tilt for positively modulated signals (L) of 6%. For a digital set which requires a small tilt the choice of tilt can be a factor of 5 or 10 smaller by increasing the AGC capacitor. TILT AT 2.2 F typ. 0.5% (line tilt) typ. 1.5% (field tilt) typ. 1.2% (frame tilt) typ. 1.5% (field tilt) 1. As long as no signal has been identified by the identification detector the unload current will be 50 A. Switching between the first three modes can be achieved by the system switch. This is a 3-level switch which when grounded selects B/G; open or 5 V selects L, and with pin 20 connected to VCC selects positively modulated MAC. The IC operates in a fourth mode if the identification capacitor at pin 19 is connected to VCC, it can be used for negatively modulated MAC. During channel switching a situation can occur that requires the AGC to increase the gain more than for example 50 dB. If this increase of gain has to be done for a positively modulated (L) signal, it will be achieved by the 500 nA load current and is therefore extremely slow. Because the identification information can be used to indicate that the signal is too small, in this event the identification circuit will mute, it is possible to increase the February 1991 5 positive unload current to the same value as that used for negatively modulated signals. This switching is fully automatic and cannot be switched off. AFC circuit The AFC circuit consists of a demodulator stage which is fed with signals 90 out of phase. A very accurate internally realized 90 phase shift circuit makes it possible to use the demodulator IF regenerator tuned circuit for tuning the AFC circuit. To prevent video ripple on the AFC output voltage a sample-and-hold circuit is used for negatively modulated signals. The output signal of the demodulator is sampled during sync level of the video signal and will be stored with the aid of an external capacitor. Philips Semiconductors Product specification Multistandard IF amplifier and demodulator This sample-and-hold circuit is not used in the L mode, but it will function as a low-pass filter in this mode and therefore also reduces the video dependency of the AFC. A gain stage amplifies the voltage swing by 5 times. The output of the AFC circuit will be an inverse analog output on pin 8 when pin 9 is connected to a voltage above 8 V. If pin 9 is connected to a voltage above 10 V the output will be a normal analog output. Normally pins 8 and 9 together provide digital AFC information. Video recognition circuit For full scart functions it is necessary to implement a second mute function for non-video signals in the whole television concept. This is realized in this IF-IC. With an internal sync separator and an internal integrator it is possible to achieve a very sensitive identification circuit, which measures the mean frequency of the input signal. This is normally approximately 16 kHz. The integrator capacitor will be loaded during the whole line time and LIMITING VALUES In accordance with the Absolute Maximum System (IEC 134) SYMBOL V14-17 Ptot Tstg Tamb total power dissipation storage temperature range operating ambient temperature range PARAMETER supply voltage (pin 14) MIN. -0.5 - -25 -25 TDA8349A unloaded during the sync pulse. The maximum voltage at this internal capacitor is a value for the main frequency of the video signal. By changing the value of an external capacitor it is possible to influence the speed and sensitivity of the recognition circuit. It is possible to gain sensitivity performance at disturbed signals by increasing the value of the external capacitor, however this will reduce the speed of the identification circuit. Video switch circuit The video switch also provides application for full SCART functions. The circuit has two inputs, one output and a control pin. The switch selects either internal or external video signals. A x 2 gain stage for the external input provides an equal output level for internal or external video from the SCART. The crosstalk of the unwanted signal is better than -50 dB and the total signal handling meets all the requirements for SCART specifications. MAX. 13.2 1.2 +150 + 75 V W C C UNIT February 1991 6 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A CHARACTERISTICS VP = 12 V; Tamb = 25 C; carrier frequency 38.9 MHz; negative modulation; unless otherwise specified. SYMBOL supply V14-17 I14 V1-2 R1-2 C1-2 G1-2 V11 V1-2 f1-2 supply voltage (pin 14) supply current Vi = 10 mV note 2 note 3 note 3 10.2 40 - - - 66 note 4 - 100 60 12 55 13.2 65 V mA V k pF dB dB mV MHz PARAMETER CONDITIONS MIN. TYP. MAX. UNIT IF amplifier (note 1) input sensitivity differential input resistance differential input capacitance gain control range output signal for 50 dB input signal variation maximum input signal maximum operating frequency 50 2 2 72 0.5 - - 80 - - - - - - Video output (note 5) zero signal output level V11 V11 V11 V11 V11(p-p) V11 V11 V11 V11 V11 Z11 I11 I11 B11 Gd d Ynl negative modulation positive modulation top sync level (top sync AGC) white level (white level AGC) amplitude of video output signal (peakto-peak value) amplitude difference (positive/negative) video output voltage variation white spot threshold level white spot insertion level noise clamping level output impedance maximum sink current maximum source current bandwidth of demodulated output signal differential gain differential phase luminance non-linearity intermodulation 1.1 MHz blue 1.1 MHz yellow 3.3 MHz blue 3.3 MHz yellow note 9 note 9 note 10 see Figs 6 and 7 - - - - -66 -60 -60 -60 - - - - dB dB dB dB VP = 1 V see Fig.3 see Fig.3 see Fig.3 note 7 note 8 note 6 - - - - 1.7 - - - - - - 5 5 7.5 - - - 4.75 2.65 2.7 4.6 1.9 0 -30 5.6 3.8 2.3 - - - 10.0 2 7 2 - - - - 2.1 10 - - - - 10 10 10 - - - 5 V V V V V % dB V V V mA mA MHz % deg % February 1991 7 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A SYMBOL S/N S/N V1(rms) V11(rms) PARAMETER signal-to-noise ratio CONDITIONS note 11 Vi = 10 mV minimum gain MIN. 54 60 - - TYP. 61 66 10 3 MAX. - - 20 10 UNIT dB dB mV mV residual carrier signal (RMS value) residual 2nd harmonic of carrier signal (RMS value) System switch (note 12) V20 I20 V20 V20 I20 V20 I20 t11 maximum voltage for mode B/G input current minimum voltage for mode L maximum voltage for mode L input current minimum voltage for MAC (positive) input current V20 = VP 3 V pin 20 7 V V20 = 0 V 1.4 - - 7 -150 - - - -300 - - - - 500 - - 3 - 250 9.5 - V A V V A V A AGC control circuit response to an amplitude increase of 52 dB of the IF input with the AGC switched to mode B/G response to an amplitude decrease of 52 dB of the IF input with the AGC switched to mode B/G allowed leakage current of the AGC capacitor I5 I5 I5 I5 top sync level AGC white level AGC positive MAC AGC negative MAC AGC - - - - 10 200 50 200 - - - - A nA nA nA note 13 - 2 - ms t11 note 14 - 25 - ms Tuner AGC (note 15) input voltage for tuner AGC starting point V3 V3 V3 V3 I4 V4 I4 Vi IF input = 200 V; negative slope IF input = 100 mV; negative slope IF input = 200 V; positive slope IF input = 100 mV; positive slope maximum current swing of tuner AGC output output saturation voltage leakage current input signal variation complete tuner control I4 = 2 mA 3.0 - 7.0 - 3 - - 0.5 3.5 5.0 7.5 9.0 5 - - 2.0 - 5.5 - 9.5 - 300 1 4.0 V V V V mA mV A dB February 1991 8 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A SYMBOL V3 PARAMETER minimum tuner take over voltage CONDITIONS - MIN. - TYP. MAX. 1 UNIT V Video switching circuit EXTERNAL VIDEO INPUT (AC coupled) V10(p-p) I10 V10 V12(p-p) |Z12| V12 V13(p-p) V13 V13 I13 I13 B13 input signal voltage (peak-to-peak value) input current top sync clamping level I10 = 1 mA VO = 2 V(p-p) VO = 2 V(p-p) - - - - - - 1.0 3.5 3.3 - - - - - - V A V INTERNAL VIDEO INPUT (DC coupled) input signal voltage (peak-to-peak value) input impedance black level input voltage 2.0 2.0 3.3 V k V VIDEO OUTPUT output signal voltage (peak-to-peak value) top sync level noise clamping voltage level internal bias current of npn emitter follower output transistor maximum source current bandwidth of output signal crosstalk of video signal V7 V7 I7 I7 external to internal internal to external note 16 - - 60 55 55 50 dB dB I13 = 1 mA - - - - 5 - 2.0 2.7 2.5 1.5 - 5 - - - - 10 - V V V mA mA MHz VIDEO SWITCH INPUT (note 17) maximum voltage for external video signal minimum voltage for internal video signal minimum source current for internal video signal input current V7 = 0 V - 1 - - - - - - 2 - 300 -1 V V A mA February 1991 9 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A SYMBOL I7 input current PARAMETER CONDITIONS V7 = VP - MIN. - TYP. MAX. 3 UNIT A AFC circuit (note 18) AFC SAMPLE-AND-HOLD/SWITCH (note 19) AFC switch: I6 I6 I6 V8(p-p) I8 current level below which AFC outputs switches off maximum AFC switch current maximum leakage current V6 = 0 V - - - - - - -500 -1 1 A mA A AFC ANALOG OUTPUT (V9 > 8 V; see Figs 4 and 5) output voltage swing (peak-to-peak value) maximum output current control steepness V8 V8,9 V8,9 f I8,9 I9 V9 V9 V9 I9 I9 V18 I18 td I19 AFC output voltage AFC off AFC DIGITAL OUTPUT (see Table 1) output voltage LOW output voltage HIGH frequency swing for switching AFC output Q1 maximum allowable output current 50 k load - 4.5 65 500 - - - 10.2 V9 = VP V9 = 8 to 10 V no sync; I18 = 1 mA output current inactive delay time of mute release after sync insertion allowed leakage current of identification detector capacitor sync - - - - 0.3 - - - 0.5 3 10 50 V A ms nA - - - - 80 - - - - - 500 150 0.5 5.5 100 - 1.5 10.2 8.0 - - - V V kHz A mA V V V A A 10 500 60 5 - - 75 6 11 - 100 7 V A mV/kHz V AFC Analog SWITCH (note 20) minimum sink current for analog AFC minimum voltage for negative slope minimum voltage for positive slope maximum voltage for positive slope output current output current Video transmitter identification output (note 21) output voltage active February 1991 10 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator Notes TDA8349A 1. All input signals are measured in RMS values at 100% carrier level and a frequency of 38.9 MHz. 2. On set AGC. 3. Input impedance selected so that a SAW filter can be applied without extra components. 4. Measured with 0 dB = 200 V. 5. Measured at 10 mV(RMS) top sync input signal and the video output unloaded. 6. Projected zero point with internally switched demodulator. 7. With the AGC switch switched to ground, for the B/G standard, or with the identification capacitor switched to VCC for the negative MAC standard. 8. With the AGC switch switched open for the L standard, or switched to VCC for the positive MAC standard. 9. Measured in accordance with the test line given in Fig.8. The differential gain is expressed as a percentage of the difference in peak amplitudes between the largest and smallest value relative to the subcarrier amplitude at blanking level. The differential phase is defined as the difference in degrees between the phase angle of the 4.4 MHz signal at 20% and 80% luminance signal. 10. Measured in accordance with the test line shown in Fig.9. The non-linearity is measured by comparing the differences between adjacent pairs of six luminance levels that make up the 5 step staircase. The measurement result is the largest percentage deviation in adjacent step values. The sign is always positive. V o black-to white 11. Measured with a 75 source: S N = 20 log -------------------------------------------------------------V n ( RMS ) at B = 5 MHz 12. The internal circuit of pin 20 behaves as an internal voltage source of 4.5 V with an input resistance of 15 k. Using the system switch three conditions can be obtained: Negative modulation with top sync level AGC. This is achieved with pin 20 connected to ground. Positive modulation with white level AGC. This is achieved with pin 20 open, or connected to 5 V. Positive modulation with top white AGC and an increased time constant for MAC signals. This is achieved with pin 20 connected to VCC. 13. Measured with a capacitor of 2.2 F connected to pin 5. A step is made from 200 V to 80 mV input signals. 14. Measured with a capacitor of 2.2 F connected to pin 5. A step is made from 80 mV to 200 V input signals. 15. It is possible to adjust the tuner AGC over the whole AGC range of the IF amplifier for both pnp and npn tuners. Tuner AGC starting point is defined as an output current of 0.2 mA for pnp and 1.8 mA for npn, in an application with a resistance of 6 k to VP at pin 4. V o unwanted video black-to-white 16. Crosstalk is defined as: 20 log --------------------------------------------------------------------------------------- measured at 4.4 MHz V o wanted video black-to-white 17. The video switch is controlled by a voltage on pin 7. The switching level is approximately 1.4 V. With pin 7 open-circuit internal video is selected; with pin 7 pulled to ground external video is selected. 18. Measurement taken with an input 10 mV(RMS). The unloaded Q factor of the reference tuned circuit is 70. 19. Switching off the AFC is obtained by a voltage of less than 2 V on pin 6. Normally this is achieved by pulling pin 6 to ground. 20. Switching to the normal analog AFC mode can be done by pulling pin 9 to a voltage above 10.2 V. Normally this is achieved by pulling pin 9 to VP. The inverse analog AFC mode can only be obtained by a voltage of between 8 and 10 V applied to pin 9. February 1991 11 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A 21. All timing figures defined with a capacitor of 2.2 nF at pin 19. The identification can be speeded up by lowering the value of this capacitor, however this makes the circuit also less sensitive if the video signal is disturbed (airplane flutter etc.). If the identification is only used as a sound mute a capacitor of 47 nF is recommended to improve the sensitivity. Fig.2 Signal-to-noise ratio as a function of video input. February 1991 12 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A Fig.3 Video waveform showing white spot threshold and insertion levels, and noise clamping levels Fig.4 Analog AFC output voltage as a function of frequency pin 9 above 10 V. Fig.5 Analog AFC output voltage as a function of frequency pin 9 above 10 V. February 1991 13 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator Table 1 Digital AFC truth table Q1 0 1 1 0 Q2 1 1 0 0 TDA8349A INPUT FREQUENCY > IF +40 kHz > IF < IF < IF -40 kHz SC = sound carrier CC = chrominance carrier PC = picture carrier all with respect to top sync level Fig.6 Input conditions for intermodulation measurements; standard colour bar with 75% contrast. Fig.7 Test set-up intermodulation measurements. February 1991 14 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator TDA8349A Fig.8 Video output signal. Fig.9 E.B.U. test signal wave form (line 330). February 1991 15 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator PACKAGE OUTLINE DIP20: plastic dual in-line package; 20 leads (300 mil) TDA8349A SOT146-1 D seating plane ME A2 A L A1 c Z e b1 b 20 11 MH wM (e 1) pin 1 index E 1 10 0 5 scale 10 mm DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.2 0.17 A1 min. 0.51 0.020 A2 max. 3.2 0.13 b 1.73 1.30 0.068 0.051 b1 0.53 0.38 0.021 0.015 c 0.36 0.23 0.014 0.009 D (1) E (1) e 2.54 0.10 e1 7.62 0.30 L 3.60 3.05 0.14 0.12 ME 8.25 7.80 0.32 0.31 MH 10.0 8.3 0.39 0.33 w 0.254 0.01 Z (1) max. 2.0 0.078 26.92 26.54 1.060 1.045 6.40 6.22 0.25 0.24 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT146-1 REFERENCES IEC JEDEC EIAJ SC603 EUROPEAN PROJECTION ISSUE DATE 92-11-17 95-05-24 February 1991 16 Philips Semiconductors Product specification Multistandard IF amplifier and demodulator SOLDERING Introduction TDA8349A There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. February 1991 17 |
Price & Availability of TDA8349
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |