 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| CXP872P48A CMOS 8-bit Single Chip Microcomputer Description The CXP872P48A is a CMOS 8-bit microcomputer which consists of A/D converter, serial interface, timer/counter, time base timer, vector interruption, high precision timing pattern generation circuit, PWM generator, PWM for tuner, VISS/VASS circuit, 32kHz timer/event counter, remote control receiving circuit, general purpose prescaler, HSYNC counter, VCR vertical sync separation circuit and the measuring circuit which measure signals of capstan FG and drum FG/PG and other servo systems, as well as basic configurations like 8-bit CPU, PROM, RAM and I/O port. They are integrated into a single chip. Also this IC provides sleep/stop function which enables to lower power consumption and ultra-low speed instruction mode in 32kHz operation. The CXP872P48A is the on-chip PROM version of the CXP87248A with on-chip mask ROM, providing the function of being able to write directly into the program. It is suitable for evaluation use during system development and for small quantity production. 100 pin QFP (Plastic) 100 pin LQFP (Plastic) Structure Silicon gate CMOS IC Features * A wide instruction set (213 instructions) which covers various types of data -- 16-bit arithmetic instruction/multiplication and division instruction/boolean bit operation instruction * Minimum instruction cycle During operation 333ns/12MHz (3.0 to 5.5V) During operation 250ns/16MHz (4.5 to 5.5V) During operation 122s/32kHz * Incorporated PROM capacity 48 Kbytes * Incorporated RAM capacity 1376 bytes * Peripheral functions -- A/D converter 8 bit, 12-channel, successive approximation system (Conversion time 20.0s/16MHz) -- Serial interface Incorporated buffer RAM (1 to 32 bytes auto transfer) 1-channel Incorporated 8-bit and 8-stage FIFO (1 to 8 bytes auto transfer) 1-channel -- Timer 8-bit timer 8-bit timer/counter 19-bit time base timer 32kHz timer/counter -- High precision timing pattern generator PPG 19-pin 32-stage programmable RTG 5-pin, 2-channel -- PWM/DA gate output PWM 12-bit, 2-channel (Repetitive frequency 62kHz/16MHz) DA gate pulse output 13-bit, 4-channel -- Servo input control Capstan FG, Drum FG/PG, CTL input -- VSYNC separator -- FRC capture unit Incorporated 26-bit and 8-stage FIFO -- PWM output 14-bit, 1-channel -- VISS/VASS circuit Pulse duty auto detection circuit -- Remote control receiving circuit 8-bit pulse measuring counter, 6-stage FIFO -- General purpose prescaler 7-bit (SYNC1 input frequency divided, FRC capture possible) -- HSYNC counter 12-bit event counter (counts SYNC1 input) * Interruption 22 factors, 15 vectors, multi-interruption possible * Standby mode SLEEP/STOP * Package 100-pin plastic QFP/LQFP Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits. -1- E94813-ST Block Diagram AVss PI4/INT1/NMI PE1/INT2 AVDD AVREF TEX TX EXTAL XTAL RST MP VDD Vss SPC700 CPU CORE PORT B CLOCK GENERATOR/ SYSTEM CONTROL PA0 to PA7 8 PB0 to PB7 CS0 SI0 SO0 SCK0 RAM PORT C SERIAL INTERFACE UNIT (CH0) PORT A AN0 to AN3 PF0/AN4 to PF7/AN11 2 8 NMI 12 A/D CONVERTER PE0/INT0 PI3/TO/DDO 8 BIT TIMER 1 PORT D PE1/EC 8 BIT TIMER/COUNTER 0 INTERRUPT CONTROLLER PI7/SI1 PI6/SO1 PI5/SCK1 FIFO 2 ROM 48K BYTES RAM 1376 BYTES SERIAL INTERFACE UNIT (CH1) 8 PC0 to PC7 8 PD0 to PD7 PE0/CKOUT 2 6 4 4 PE0 to PE1 PORT E PG4/SYNC0 PG5/SYNC1 2 2 2 VSYNC SEPARATOR PE2 to PE7 PF0 to PF3 PORT F PG6/EXI0 PG7/EXI1 PI1/RMC REMOCON INPUT FIFO 32kHz TIMER/COUNTER PI2/PWM 14 BIT PWM GENERATOR 2 PORT H VISS/VASS PORT G 12 BIT PWM GENERATOR CH0 2 PROGRAMMABLE PATTERN GENERATOR RAM REALTIME PULSE GENERATOR CH0 CH 1 12 BIT PWM GENERATOR CH1 4 PORT I PE2/PWM0 PE4/DAA0 PE6/DAB0 PE3/PWM1 PE5/DAA1 PE7/DAB1 PROGRAMMABLE PRESCALER PE1/HCOUT HSYNC COUNTER 19 5 PI3/ADJ PC3/RTO3 to PC7/RTO7 PORT J PA0/PPO0 to PC2/PPO18 -2- 3 FIFO FRC CAPTURE UNIT CAPSTAN PRESCALER/ TIME BASE TIMER PF4 to PF7 DRUM PG0/CFG PG1/DFG PG2/DPG PG3/PBCTL CTL SERVO INPUT CONTROL 8 PG0 to PG7 8 PH0 to PH7 7 PI1 to PI7 8 PJ0 to PJ7 CXP872P48A CXP872P48A Pin Assignment 1 (Top View) 100-pin QFP package PI3/TO/DDO/ADJ PB6/PPO14 PB7/PPO15 PA0/PPO0 PA1/PPO1 PA2/PPO2 PA3/PPO3 PA4/PPO4 PA5/PPO5 PA6/PPO6 PA7/PPO7 PI4/INT1/NMI Vpp VSS 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 PB5/PPO13 PB4/PPO12 PB3/PPO11 PB2/PPO10 PB1/PPO9 PB0/PPO8 PC7/RTO7 PC6/RTO6 PC5/RTO5 PC4/RTO4 PC3/RTO3 PC2/PPO18 PC1/PPO17 PC0/PPO16 PJ7 PJ6 PJ5 PJ4 PJ3 PJ2 PJ1 PJ0 PD7 PD6 PD5 PD4 PD3 PD2 PD1 PD0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 PI6/SO1 PI7/SI1 PE0/INT0/CKOUT PE1/EC/INT2/HCOUT PE2/PWM0 PE3/PWM1 PE4/DAA0 PE5/DAA1 PE6/DAB0 PE7/DAB1 PG0/CFG PG1/DFG PG2/DPG PG3/PBCTL PG4/SYNC0 PG5/SYNC1 PG6/EXI0 PG7/EXI1 AN0 AN1 AN2 AN3 PF0/AN4 PF1/AN5 PF2/AN6 PF3/AN7 AVDD AVREF AVSS PF4/AN8 TX TEX VDD PI1/RMC PI2/PWM Note) 1. Vpp (Pin 90) is always connected to VDD. 2. VSS (Pins 41 and 88) are both connected to GND. -3- PF7/AN11 PF6/AN10 PF5/AN9 EXTAL SCK0 XTAL RST SO0 PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 CS0 VSS MP SI0 PI5/SCK1 CXP872P48A Pin Assignment 2 (Top View) 100-pin LQFP package PI3/TO/DDO/ADJ PB4/PPO12 PB5/PPO13 PB6/PPO14 PB7/PPO15 PA0/PPO0 PA1/PPO1 PA2/PPO2 PA3/PPO3 PA4/PPO4 PA5/PPO5 PA6/PPO6 PA7/PPO7 PI4/INT1/NMI PI1/RMC PI2/PWM PI5/SCK1 PI6/SO1 VSS 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 PB3/PPO11 PB2/PPO10 PB1/PPO9 PB0/PPO8 PC7/RTO7 PC6/RTO6 PC5/RTO5 PC4/RTO4 PC3/RTO3 PC2/PPO18 PC1/PPO17 PC0/PPO16 PJ7 PJ6 PJ5 PJ4 PJ3 PJ2 PJ1 PJ0 PD7 PD6 PD5 PD4 PD3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 PE1/EC/INT2/HCOUT PE2/PWM0 PE3/PWM1 PE4/DAA0 PE5/DAA1 PE6/DAB0 PE7/DAB1 PG0/CFG PG1/DFG PG2/DPG PG3/PBCTL PG4/SYNC0 PG5/SYNC1 PG6/EXI0 PG7/EXI1 AN0 AN1 AN2 AN3 PF0/AN4 PF1/AN5 PF2/AN6 PF3/AN7 AVDD AVRE TX TEX Vpp VDD PF5/AN9 PF4/AN8 PI7/SI1 Note) 1. Vpp (Pin 88) is always connected to VDD. 2. VSS (Pins 39 and 86) are both connected to GND. -4- PF7/AN11 PF6/AN10 EXTAL SCK0 XTAL AVSS SO0 RST PD2 PD1 PD0 PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 CS0 VSS SI0 MP PE0/INT0/CKOUT CXP872P48A Pin Description Symbol PA0/PPO0 to PA7/PPO7 I/O Output/Real time output (Port A) 8-bit output port. Data is gated with PPO contents by OR-gate and they are output. (8 pins) (Port B) 8-bit output port. Data is gated with PPO contents by OR-gate and they are output. (8 pins) (Port C) 8-bit I/O port, enables to specify I/O by bit unit. Data is gated with PPO or RTO contents by OR-gate and they are output. (8 pins) Description PB0/PPO8 to PB7/PPO15 PC0/PPO16 to PC2/PPO18 PC3/RTO3 to PC7/RTO7 Output/Real time output Programmable pattern generator (PPG) output. Functions as high precision real time pulse output port. (19 pins) PB0 and PB2 can be 3-state controlled with PPG. I/O/Real time output I/O/Real time output Real time pulse generator (RTG) output. Functions as high precision real time pulse output port. (5 pins) PC3 can be 3-state controlled with RTG. PD0 to PD7 I/O (Port D) 8-bit I/O port. Enables to specify I/O by 4-bit unit. Enables to drive 12 mA sink current. (8 pins) Input pin to request external interruption. Active when falling edge. System clock frequency division output. PE0/INT0/ CKOUT Input/Input/Output PE1/EC/ INT2/HCOUT PE2/PWM0 PE3/PWM1 PE4/DAA0 PE5/DAA1 PE6/DAB0 PE7/DAB1 AN0 to AN3 PF0/AN4 to PF3/AN7 PF4/AN8 to PF7/AN11 SCK0 SO0 SI0 CS0 Input/Input/Input/ Output Output/Output Output/Output Output/Output Output/Output Output/Output Output/Output Input Input/Input (Port E) 8-bit port. Lower 2 bits are input port and upper 6 bits are output port. (8 pins) External event input pin for timer/counter. Input pin to request Output pin for external interruption. HSYNC counter Active when falling matching signal. edge. PWM output pins. (2 pins) DA gate pulse output pins. (4 pins) Analog input pins to A/D converter. (12 pins) (Port F) Lower 4 bits are input port and upper 4 bits are output port. Lower 4 bits also serve as standby release input pins. (8 pins) Serial clock (CH0) I/O pin. Serial data (CH0) output pin. Serial data (CH0) input pin. Serial chip select (CH0) input pin. -5- Output/Input I/O Output Input Input CXP872P48A Symbol PG0/CFG PG1/DFG PG2/DPG PG3/PBCTL PG4/SYNC0 PG5/SYNC1 PG6/EXI0 PG7/EXI1 I/O Input/Input Input/Input Input/Input Input/Input Input/Input Input/Input Input/Input Input/Input (Port G) 8-bit input port. (8 pins) Description Capstan FG input pin. Drum FG input pin. Drum PG input pin. Playback CTL pulse input pin. External event input pin of timer/counter. Composite sync signal input pin. External input pin to FRC capture unit. (Port H) 8-bit output port; Medium withstand voltage (12V) and high current (12 mA), N-ch open drain output. (8 pins) Remote control receiving circuit input pin. 14-bit PWM output pin. (Port I) 7-bit I/O port. Enables to specify I/O by bit unit. (7 pins) Timer/counter, CTL duty detection, 32kHz oscillation adjustment output pin. Input pin to request external interruption and non-maskable interruption. Active when falling edge. Serial clock (CH1) I/O pin. Serial data (CH1) output pin. Serial data (CH1) input pin. (Port J) 8-bit I/O port. Function as standby release input can be specified by bit unit. Enables to specify I/O by bit unit. Connection pin of crystal oscillator for system clock. When supplying the external clock, input the external clock to EXTAL pin and input opposite phase clock to XTAL pin. Connection pin of crystal oscillator for 32kHz timer clock. When used as event counter, input to TEX pin and leave TX pin open. (Feedback resistor is not removed.) System reset pin of active "L" level. Microprocessor mode input pin. Always connect to GND. Positive power supply pin of A/D converter. PH0 to PH7 Output PI1/RMC PI2/PWM PI3/TO/ DDO/ADJ PI4/INT1/ NMI PI5/SCK1 PI6/SO1 PI7/SI1 PJ0 to PJ7 EXTAL XTAL TEX TX RST MP AVDD AVREF AVss VDD Vpp Vss I/O/Input I/O/Output I/O/Output/Output /Output I/O/Input/Input I/O/I/O I/O/Output I/O/Input I/O Input Output Input Output Input Input Input Reference voltage input pin of A/D converter. GND pin of A/D converter. Positive power supply pin. Positive power supply pin used for writing incorporated PROM. Connect to VDD during normal operation. GND pin. Connect both VSS pins to GND. -6- CXP872P48A Input/Output Circuit Formats for Pins Pin Port A Port B PA0/PPO0 to PA7/PPO7 PB4/PPO12 to PB7/PPO15 PPO data Circuit format When reset Port A or Port B Hi-Z Data bus RD (Port A or Port B) Output becomes active from high impedance by data writing to port register. 12 pins PPO8 or PPO10 PB0/PPO8 PB2/PPO10 Data bus PB0 or PB2 data RD (Port B) Hi-Z Output becomes active from high impedance by data writing to port register. PPO9 or PPO11 2 pins PPG control status register bit 0 3-state control selection PPO9 or PPO11 PB1 or PB3 data PB1/PPO9 PB3/PPO11 Data bus RD (Port B) Output becomes active from high impedance by data writing to port register. Hi-Z 2 pins -7- CXP872P48A Pin Port C Circuit format When reset PC0/PPO16 to PC2/PPO18 PC5/RTO5 to PC7/RTO7 PPO, RTO data Port C data IP (Every bit) Data bus RD (Port C) Data bus Input protection circuit Port C direction Hi-Z 6 pins RD (Port C direction) RTO3 PC3 data PC3 direction PC3/RTO3 Data bus RD (Port C) Data bus RTO4 RD (Port C direction) IP Hi-Z 1 pin RTG interruption control register bit 7 3-state control selection RTO4 PC4 data PC4/RTO4 Data bus PC4 direction Hi-Z IP RD (Port C) Data bus RD (Port C direction) RTO data is OR-gate data of ch0 and ch1. 1 pin -8- CXP872P48A Pin Port D Circuit format When reset PD0 to PD7 Port D data IP (Every 4 bits) PD0 to 3 PD4 to 7 RD (Port D) High current 12mA Hi-Z Port D direction Data bus 8 pins Port E Port E/PWM selection register bit 0, 1 PE0/INT0 /CKOUT PS1 PS2 PS3 MPX Hi-Z IP Input protection circuit Data bus RD (Port E) Interruption circuit 1 pin Port E Hi-Z control From HSYNC counter HCOUT PE1/EC/INT2 /HCOUT Data bus RD (Port E) To interruption circuit/event counter IP Input protection circuit Hi-Z 1 pin -9- CXP872P48A Pin Port E DA gate output or PWM output Circuit format When reset PE2/PWM0 PE3/PWM1 PE4/DAA0 PE5/DAA1 Hi-Z control Port E data MPX Hi-Z Port/DA output select Data bus 4 pins Port E RD (Port E) DA gate output Hi-Z control MPX PE6/DAB0 PE7/DAB1 Port E data H level Port/DA output select Data bus 2 pins RD (Port E) AN0 to AN3 4 pins Port F PF0/AN4 to PF3/AN7 Input multiplexer Hi-Z IP A/D converter Input multiplexer IP A/D converter Hi-Z Data bus 4 pins RD (Port F) - 10 - CXP872P48A Pin Port F Circuit format When reset PF4/AN8 to PF7/AN11 Port F data Data bus RD (Port F) Port/AD select Input multiplexer IP A/D converter Hi-Z 4 pins PG0/CFG PG1/DFG PG2/DPG PG3/PBCTL PG4/SYNC0 PG5/SYNC1 PG6/EXI0 PG7/EXI1 8 pins Port G Schmitt input IP Servo input Data bus RD (Port G) Note) For PG4/SYNC0, PG5/SYNC1, there are CMOS schmitt input and TTL schmitt input. Hi-Z Port H PH0 to PH7 Medium withstand voltage 12V Port H data Hi-Z High current 12mA Data bus 8 pins RD (Port H) Port I Port I function select PI2: From 14-bit PWM From timer/counter, PI3: CTL duty detection circuit, 32kHz timer Port I data Port I direction PI2/PWM PI3/TO/ DDO/ADJ MPX Hi-Z IP Data bus 2 pins RD (Port I) - 11 - CXP872P48A Pin Port I Port I data Circuit format When reset PI1/RMC PI4/INT1/NMI PI7/SI1 Data bus Port I direction IP RD (Port I) PI1: To remote control circuit PI4: To interruption circuit PI7: To serial CH1 Schmitt input Hi-Z 3 pins Port I Port I function select From serial CH1 Port I data Port I direction Data bus MPX Note) PI5 is schmitt input PI6 is inverter input PI5/SCK1 PI6/SO1 MPX Hi-Z IP 2 pins Port J RD (Port I) To serial CH1 Port J data PJ0 to PJ7 Port J direction IP Data bus RD (Port J) Standby release Data bus RD Edge detection Hi-Z 8 pins CS0 SI0 IP Schmitt input To SIO Hi-Z 2 pins SO0 SO0 from SIO Hi-Z 1 pin SO0 output enable - 12 - CXP872P48A Pin Circuit format When reset SCK0 Internal serial clock from SIO IP SCK0 output enable External serial clock to SIO Hi-Z 1 pin Schmitt input EXTAL XTAL EXTAL * Shows the circuit composition during oscillation. IP * Feedback resistor is removed during stop. Oscillation 2 pins XTAL TEX TX To 32kHz timer counter TEX IP * Shows the circuit composition during oscillation. * Feedback resistor is removed during 32kHz oscillation circuit stop by software. At this time TEX pin outputs "L" level and TX pin outputs "H" level. Oscillation 2 pins TX RST Mask option Pull-up resistor Schmitt input OP IP L level 1 pin MP IP CPU mode Hi-Z 1 pin - 13 - CXP872P48A Absolute Maximum Ratings Item Symbol VDD Vpp Supply voltage AVDD AVSS Input voltage Output voltage Medium withstand output voltage High level output current High level total output current Low level output current Low level total output current Operating temperature Storage temperature Allowable power dissipation VIN VOUT VOUTP IOH IOH IOL IOLC IOL Topr Tstg PD Rating -0.3 to +7.0 -0.3 to +13 AVss to +7.01 -0.3 to +0.3 -0.3 to +7.02 -0.3 to +7.02 -0.3 to +15.0 -5 -50 15 20 130 -10 to +75 -55 to +150 600 380 mW Unit V V V V V V V mA mA mA mA mA C C QFP package type LQFP package type Total of output pins PH pin Remarks (Vss = 0V) Unique to version with incorporated PROM Other than high current output pins: per pin High current port output pin3: per pin Total of output pins 1 AVDD and VDD should be set to a same voltage. 2 VIN and VOUT should not exceed VDD + 0.3V. 3 The high current operation transistors are the N-ch transistors of the PD and PH ports. Note) Usage exceeding absolute maximum ratings may permanently impair the LSI. Normal operation should better take place under the recommended operating conditions. Exceeding those conditions may adversely affect the reliability of the LSI. - 14 - CXP872P48A Recommended Operating Conditions Item Symbol Min. 3.0 VDD Supply voltage 2.7 2.5 Vpp Analog supply voltage AVDD VIH VIHS High level input voltage VIHTS VIHEX 5.5 5.5 V V V V V V V V V V V V V C 2.7 Max. 5.5 5.5 V Unit Remarks (Vss = 0V) High-speed mode guaranteed operation range (1/2 dividing clock) Low-speed mode guaranteed operation range (1/16 dividing clock) Guaranteed operation range by TEX clock Guaranteed data hold range during STOP 10 1 2 CMOS schmitt input3 and PE0/INT0 pin CMOS schmitt input7 TTL schmitt input4 EXTAL pin5, 8 TEX pin6, 8 EXTAL pin5, 9 TEX pin6, 9 2, 8 2, 9 CMOS schmitt input3 and PE0/INT0 pin TTL schmitt input4 EXTAL pin5, 8 TEX pin6, 8 EXTAL pin5, 9 TEX pin6, 9 Vpp = VDD 3.0 0.7VDD 0.8VDD 2.2 5.5 VDD VDD 5.5 5.5 VDD - 0.4 VDD + 0.3 VDD - 0.2 VDD + 0.2 0.3VDD VIL Low level input voltage VILS VILTS VILEX Operating temperature 1 2 3 4 5 6 7 8 9 10 Topr 0 0 0 -0.3 -0.3 -10 0.2VDD 0.2VDD 0.8 0.4 0.2 +75 AVDD and VDD should be set to a same voltage. Normal input port (each pin of PC, PD, PF0 to PF3, PG, PI and PJ), MP pin. Each pin of SCK0, RST, PE1/EC/INT2, PI1/RMC, PI4/INT1/NMI, PI5/SCK1 and PI7/SI1. Each pin of PG4 and PG5 (When TLL schmitt input is selected for the product) It specifies only when the external clock is input. It specifies only when the external event count is input. Each pin of CS0, SI0, and PG (When CMOS schmitt input is selected for the product) When the supply voltage (VDD) is within a range from 4.5 to 5.5V. When the supply voltage (VDD) is within a range from 3.0 to 3.6V. Vpp should be the same voltage as VDD. - 15 - CXP872P48A DC Characteristics Supply Voltage (VDD) 4.5 to 5.5V Item Symbol Pins PA to PD, PE2 to PE7, PF4 to PF7, PH (VOL only) PI1 to PI7 PJ, SO0, SCK0 PD, PH IIHE IILE Input current IIHT IILT IILR TEX RST1 PA to PG, PI, PJ, MP AN0 to AN3, CS0, SI0, SO0 SCK0, RST1 VDD = 5.5V, VIL = 0.4V EXTAL Conditions VDD = 4.5V, IOH = -0.5mA VDD = 4.5V, IOH = -1.2mA VDD = 4.5V, IOL = 1.8mA VDD = 4.5V, IOL = 3.6mA VDD = 4.5V, IOL = 12.0mA VDD = 5.5V, VIH = 5.5V VDD = 5.5V, VIL = 0.4V VDD = 5.5V, VIH = 5.5V 0.5 -0.5 0.1 -0.1 -1.5 (Ta = -10 to +75C, Vss = 0V) Min. 4.0 3.5 0.4 0.6 1.5 40 -40 10 -10 -400 Typ. Max. Unit V V V V V A A A A A High level VOH output voltage Low level output voltage VOL I/O leakage current Open drain output leakage current (N-ch Tr OFF in state) IIZ VDD = 5.5V, VI = 0, 5.5V 10 A ILOH PH VDD = 5.5V VOH = 12V 16MHz crystal oscillation (C1 = C2 = 15pF) VDD = 5V 0.5V3 SLEEP mode VDD = 5V 0.5V 50 A IDD1 27 45 mA IDDS1 2 8 mA Supply current2 IDD2 32kHz crystal oscillation (C1 = C2 = 47pF) VDD VDD = 3V 0.3V SLEEP mode 500 1000 A IDDS2 VDD = 3V 0.3V IDDS3 Input capacitance Other than VDD, Vss, AVDD, and AVss 10 30 A STOP mode (EXTAL and TEX pins oscillation stop) VDD = 5V 0.5V 30 A CIN Clock 1MHz 0V other than the measured pins 10 20 pF 1 RST pin specifies the input current when the pull-up resistor is selected, and specifies leakage current when non-resistor is selected. 2 When entire output pins are open. 3 When setting upper 2 bits (CPU clock selection) of clock control register CLC (address: 00FEH) to "00" and operating in high speed mode (1/2 dividing clock). - 16 - CXP872P48A Supply Voltage (VDD) 3.0 to 3.6V Item Symbol Pins PA to PD, PE2 to PE7, PF4 to PF7, PH (VOL only) PI1 to PI7 PJ, SO0, SCK0 PD, PH IIHE IILE Input current IIHT IILT IILR TEX RST1 PA to PG, PI, PJ, MP AN0 to AN3, CS0, SI0, SO0 SCK0, RST1 PH VDD = 3.6V, VIL = 0.3V EXTAL Conditions VDD = 3.0V, IOH = -0.15mA VDD = 3.0V, IOH = -0.5mA VDD = 3.0V, IOL = 1.2mA VDD = 3.0V, IOL = 1.6mA VDD = 3.0V, IOL = 5mA VDD = 3.6V, VIH = 3.6V VDD = 3.6V, VIL = 0.3V VDD = 3.6V, VIH = 3.6V (Ta = -10 to +75C, Vss = 0V) Min. 2.7 2.3 0.3 0.5 1.0 0.3 -0.3 0.1 -0.1 -0.9 20 -20 10 -10 -200 Typ. Max. Unit V V V V V A A A A A High level VOH output voltage Low level output voltage VOL I/O leakage current IIZ VDD = 3.6V, VI = 0, 3.6V 10 A Open drain output leakage current ILOH VDD = 3.6V, VOH = 12V 12MHz crystal oscillation (C1 = C2 = 15pF) VDD = 3.3V 0.3V3 SLEEP mode 12 50 A IDD1 25 mA Supply current2 IDDS1 VDD VDD = 3.3V 0.3V STOP mode (EXTAL and TEX pins oscillation stop) VDD = 3.3V 0.3V 0.8 2.5 mA IDDS3 30 A Input capacitance CIN Other than VDD, Vss, AVDD, and AVss Clock 1MHz 0V other than the measured pins 10 20 pF 1 RST pin specifies the input current when the pull-up resistor is selected, and specifies leakage current when non-resistor is selected. 2 When entire output pins are open. 3 When setting upper 2 bits (CPU clock selection) of clock control register CLC (address: 00FEH) to "00" and operating in high speed mode (1/2 dividing clock). - 17 - CXP872P48A AC Characteristics (1) Clock timing Item System clock frequency Symbol fC Pins XTAL EXTAL XTAL EXTAL XTAL EXTAL EC EC TEX TX TEX TEX (Ta = -10 to +75C, VDD = 3.0 to 5.5V, VSS = 0V) Conditions Fig. 1, Fig. 2 VDD = 4.5 to 5.5V Min. 1 1 Fig. 1, Fig. 2 VDD = 4.5 to 5.5V (External clock drive) Fig. 1, Fig. 2 (External clock drive) Fig. 3 Fig. 3 Fig. 2 VDD = 2.7 to 5.5V 32.768 (32kHz clock applied condition) Fig. 3 Fig. 3 10 20 28 37.5 200 ns ns 20 ns kHz s ms Max. 16 12 ns Unit MHz System clock input pulse width System clock input rise and fall times Event count clock input pulse width Event count clock input rise and fall times System clock frequency Event count clock input pulse width Event count clock input rise and fall times tXL, tXH tCR, tCF tEH, tEL tER, tEF fC tsys x 4 tTL, tTH tTR, tTF tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Fig. 1. Clock timing 1/fc VDD - 0.4V EXTAL 0.4V tXH tCF tXL tCR Fig. 2. Clock applied condition Crystal oscillation Ceramic oscillation External clock 32kHz clock applied condition Crystal oscillation EXTAL XTAL EXTAL XTAL TEX TX C1 C2 74HC04 C1 C2 Fig. 3. Event count clock timing 0.8VDD 0.2VDD TEX EC tEH tTH tEF tTF tEL tTL tER tTR - 18 - CXP872P48A (2) Serial transfer (CH0) Item CS SCK delay time CS SCK floating delay time CS SO delay time CS SO floating delay time CS high level width SCK cycle time SCK high and low level widths SI input set-up time (against SCK ) SI input hold time (against SCK ) SCK SO delay time Note 1) Symbol Pins SCK0 (Ta = -10 to +75C, VDD = 4.5 to 5.5V, VSS = 0V) Conditions Chip select transfer mode (SCK = output mode) Chip select transfer mode (SCK = output mode) Chip select transfer mode Chip select transfer mode Chip select transfer mode Input mode Output mode Input mode Output mode SCK input mode SCK output mode SCK input mode SCK output mode SCK input mode SCK output mode Min. Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns 2tsys + 200 100 ns ns tDCSK tsys + 200 tsys + 200 tsys + 200 tsys + 200 tsys + 200 2tsys + 200 8000/fc tDCSKF SCK0 tDCSO SO0 tDCSOF SO0 tWHCS CS0 tKCY tKH tKL tSIK tKSI tKSO SCK0 SCK0 tsys + 100 8000/fc - 100 -tsys + 100 200 2tsys + 100 100 SI0 SI0 SO0 tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) CS, SCK, SI and SO mean each pin of CS CS0, SCK SCK0, SI SI0, and SO SO0 respectively. Note 3) The load of SCK output mode and SO output delay time is 50pF + 1 TTL. - 19 - CXP872P48A (2) Serial transfer (CH0) Item CS SCK delay time CS SCK floating delay time CS SO delay time CS SO floating delay time CS high level width SCK cycle time SCK high and low level widths SI input set-up time (against SCK ) SI input hold time (against SCK ) SCK SO delay time Note 1) Symbol Pins SCK0 (Ta = -10 to +75C, VDD = 3.0 to 3.6V, VSS = 0V) Conditions Chip select transfer mode (SCK = output mode) Chip select transfer mode (SCK = output mode) Chip select transfer mode Chip select transfer mode Chip select transfer mode Input mode Output mode Input mode Output mode SCK input mode SCK output mode SCK input mode SCK output mode SCK input mode SCK output mode Min. Max. Unit ns ns ns ns ns ns ns ns ns ns ns ns ns 2tsys + 250 125 ns ns tDCSK tsys + 250 tsys + 200 tsys + 250 tsys + 200 tsys + 200 2tsys + 200 8000/fc tDCSKF SCK0 tDCSO SO0 tDCSOF SO0 tWHCS CS0 tKCY tKH tKL tSIK tKSI tKSO SCK0 SCK0 tsys + 100 8000/fc - 150 -tsys + 100 200 2tsys + 100 100 SI0 SI0 SO0 tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) CS, SCK, SI and SO mean each pin of CS CS0, SCK SCK0, SI SI0, and SO SO0 respectively. Note 3) The load of SCK output mode and SO output delay time is 50pF. - 20 - CXP872P48A Fig. 4. Serial transfer timing (CH0) tWHCS CS0 0.8VDD 0.2VDD tKCY tDCSK tKL tKH tDCSKF 0.8VDD SCK0 0.2VDD 0.8VDD tSIK tKSI 0.8VDD SI0 Input data 0.2VDD tDCSO tKSO tDCSOF 0.8VDD SO0 Output data 0.2VDD - 21 - CXP872P48A Serial transfer (CH1) (SIO mode) Item SCK1 cycle time Symbol Pins (Ta = -10 to +75C, VDD = 4.5 to 5.5V, VSS = 0V) Conditions Input mode Output mode SCK1 Input mode Output mode SI1 SCK1 input mode SCK1 output mode SI1 SCK1 input mode SCK1 output mode SO1 SCK1 input mode SCK1 output mode Min. 2tsys + 200 16000/fc Max. Unit ns ns ns ns ns ns ns ns tKCY tKH tKL tSIK tKSI tKSO SCK1 SCK1 high and low level widths SI1 input set-up time (against SCK1 ) SI1 input hold time (against SCK1 ) SCK1 SO1 delay time Note 1) tsys + 100 8000/fc - 50 100 200 tsys + 200 100 tsys + 200 100 ns ns tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) The load of SCK1 output mode and SO1 output delay time is 50pF + 1 TTL. Serial transfer (CH1) (SIO mode) Item SCK1 cycle time Symbol Pins (Ta = -10 to +75C, VDD = 3.0 to 3.6V, VSS = 0V) Conditions Input mode Output mode SCK1 Input mode Output mode SCK1 input mode SCK1 output mode SI1 SCK1 input mode SCK1 output mode SCK1 input mode SCK1 output mode Min. 2tsys + 200 16000/fc Max. Unit ns ns ns ns ns ns ns ns tKCY tKH tKL tSIK tKSI tKSO SCK1 SCK1 high and low level widths SI1 input set-up time (against SCK1 ) SI1 input hold time (against SCK1 ) SCK1 SO1 delay time Note 1) tsys + 100 8000/fc - 150 100 200 SI1 tsys + 200 100 SO1 tsys + 250 125 ns ns tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) The load of SCK1 output mode and SO1 output delay time is 50pF. - 22 - CXP872P48A Fig. 5. Serial transfer CH1 timing (SIO mode) tKCY tKL tKH SCK1 0.8VDD 0.2VDD tSIK tKSI 0.8VDD SI1 Input data 0.2VDD tKSO 0.8VDD SO1 0.2VDD Output data - 23 - CXP872P48A Serial transfer (CH1) (Special mode) Item SO1 cycle time SI1 data set-up time SI1 data hold time Symbol Pins SO1 SI1 SI1 SI1 (Ta = -10 to +75C, VDD = 4.5 to 5.5V, VSS = 0V) Conditions Note 1) 2 2 Min. Typ. 104 Max. unit s s s tLCY tLSU tLHD Note 1) tLCY specifies only serial mode register (CH1) (SIOM1: address 01FAH) lower 2 bits (SO1 clock selection) has been set at 104s. Note 2) The load of SO1 pin is 50pF + 1 TTL. Serial transfer (CH1) (Special mode) Item SO1 cycle time SI1 data set-up time SI1 data hold time Symbol Pins SO1 SI1 SI1 SI1 (Ta = -10 to +75C, VDD = 3.0 to 3.6V, VSS = 0V) Conditions Note 1) 2 2 Min. Typ. 104 Max. unit s s s tLCY tLSU tLHD Note 1) tLCY specifies only serial mode register (CH1) (SIOM1: address 01FAH) lower 2 bits (SO1 clock selection) has been set at 104s. Note 2) The load of SO1 pin is 50pF. Fig. 6. Serial transfer CH1 timing (Special mode) tLCY tLCY SO1 Start bit Output data bit 0.5VDD tLCY/2 tLSU tLHD 0.8VDD 0.2VDD SI1 Input data bit - 24 - CXP872P48A (3) General purpose prescaler Item External clock input frequency External clock input pulse width External clock input rise and fall times Symbol fPCK Pins SYNC1 SYNC1 SYNC1 (Ta = -10 to +75C, VDD = 3.0 to 5.5V, VSS = 0V) Conditions Min. Typ. Max. 12 33 200 Unit MHz ns ns tWH, tWL tR tF Fig. 7. General purpose prescaler timing 1/fPCK tWH tF 0.8VDD SYNC1 0.5VDD 0.2VDD tWL tR - 25 - CXP872P48A (4) HSYNC counter Item External clock input frequency External clock input pulse width External clock input rise and fall times HCOUT output delay time (against SYNC1 ) HCOUT output rise and fall times Note 1) Symbol fHCK Pins SYNC1 SYNC1 SYNC1 (Ta = -10 to + 75C, VDD = 3.0 to 5.5V, VSS = 0V) Conditions Min. Typ. Max. unit tWH, tWL tR tF tHLH tHHL tTLH tTHL 33 HCOUT External clock input SYNC1 tR = tF = 6ns External clock input SYNC1 tR = tF = 6ns tsys + 130 tsys + 90 100 30 HCOUT tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") Note 2) The load of HCOUT pin is 50pF. Fig. 8. HSYNC counter timing 1/fHCK tWH SYNC1 tF 0.8VDD 0.5VDD 0.2VDD tR tWL tHLH 0.8VDD HCOUT 0.5VDD 0.2VDD tHHL tTLH tTHL - 26 - CXP872P48A (5) A/D converter characteristics Item Resolution Linearity error Absolute error Conversion time Sampling time Symbol (Ta = -10 to +75C, VDD = AVDD = 4.5 to 5.5V, AVREF = 4.0 to AVDD, Vss = AVSS = 0V) Pins Conditions Ta = 25C VDD = AVDD = AVREF = 5.0V VSS = AVSS = 0V Min. Typ. Max. 8 1 2 160/fADC 12/fADC Unit Bits LSB LSB s s AVDD V V 0.6 1.0 10 mA A tCONV tSAMP AVREF AN0 to AN11 Operating mode AVREF IREFS SLEEP mode STOP mode 32kHz operating mode VDD = AVDD = 4.5 to 5.5V VIAN IREF Reference input voltage VREF Analog input voltage AVDD - 0.5 0 AVREF current (Ta = -10 to +75C, VDD = AVDD = 3.0 to 3.6V, AVREF = 2.7 to AVDD, Vss = AVSS = 0V) Item Resolution Linearity error Absolute error Conversion time Sampling time Ta = 25C VDD = AVDD = AVREF = 5.0V VSS = AVSS = 0V Symbol Pins Conditions Min. Typ. Max. 8 1 2 160/fADC 12/fADC AVREF AN0 to AN11 Operating mode AVREF IREFS SLEEP mode STOP mode 32kHz operating mode VDD = AVDD = 3.0 to 3.6V AVDD - 0.3 0 0.4 0.7 10 AVDD Unit Bits LSB LSB s s V V mA A tCONV tSAMP VIAN IREF Reference input voltage VREF Analog input voltage AVREF current Fig. 9. Definitions of A/D converter terms FFH FEH Digital conversion value The value of fADC is as follows by selecting ADC operation clock (MSC: address 01FFH bit 0). When PS2 is selected, fADC = fc/2 When PS1 is selected, fADC = fc Linearity error 01H 00H VZT Analog input VFT - 27 - CXP872P48A (6) Interruption, reset input Item Symbol (Ta = -10 to +75C, VDD = 3.0 to 5.5V, Vss = 0V) Pins INT0 INT1 INT2 NMI PJ0 to PJ7 RST Conditions Min. Max. Unit External interruption high and low level widths tIH tIL tRSL 1 s Reset input low level width 32/fc s Fig. 10. Interruption input timing INT0 INT1 INT2 NMI PJ0 to PJ7 (During standby release input) (Falling edge) tIH tIL 0.8VDD 0.2VDD Fig. 11. Reset input timing tRSL RST 0.2VDD (7) Others Item CFG input high and low level widths Symbol Pins CFG DFG DPG DPG PBCTL EXI0 EXI1 (Ta = -10 to +75C, VDD = 3.0 to 5.5V, Vss = 0V) Conditions Min. Max. Unit ns ns ns ns ns ns tCFH tCFL DFG input high and low tDFH tDFL level widths DPG minimum pulse width tDPW DPG minimum removal time PBCTL input high and low level widths EXI input high and low level widths Note) tFRC x 24 + 200 tFRC x 16 + 200 tFRC x 8 + 200 tFRC x 16 + 200 tsys = 2000/fc tsys = 2000/fc tFRC x 8 + 200 + tsys tFRC x 8 + 200 + tsys trem tCTH tCTL tEIH tEIL tsys indicates three values according to the contents of the clock control register (address; 00FEH) upper 2 bits (CPU clock selection). tsys [ns] = 2000/fc (Upper 2 bits = "00"), 4000/fc (Upper 2 bits = "01"), 16000/fc (Upper 2 bits = "11") tFRC = 1000/fc [ns] - 28 - CXP872P48A Fig. 12. Other timings tCFH tCFL CFG 0.8VDD 0.2VDD tDFH tDFL 0.8VDD DFG 0.2VDD tDPW trem trem 0.8VDD DPG tCTH tCTL 0.8VDD PBCTL 0.2VDD tEIH tEIL EXI0 EXI1 0.8VDD 0.2VDD - 29 - CXP872P48A Appendix Fig. 13. Recommended oscillation circuit (i) (ii) EXTAL XTAL Rd TEX TX Rd C1 C2 C1 C2 Manufacturer Model fc (MHz) 8.00 C1 (pF) 10 C2 (pF) 10 Rd () Circuit example RIVER ELETEC CO., LTD. HC-49/U03 10.00 12.00 16.00 8.00 16 (12) 16 (12) 12 12 30 16 (12) 16 (12) 12 12 18 5 5 0 (i) 0 0 0 470K (ii) (i) HC-49/U (-S) KINSEKI LTD. 10.00 12.00 16.00 P3 32.768kHz Product List Optional item Package ROM capacity Reset pin pullup resistor Input circuit format Mask product 100-pin plastic QFP/LQFP 40K bytes /48K bytes Existent /non-existent CMOS schmitt /TTL schmitt CXP872P48AQ-1 CXP872P48AR-1 CXP872P48AQ-2 CXP872P48AR-2 100-pin plastic QFP 100-pin plastic LQFP 100-pin plastic QFP 100-pin plastic LQFP PROM 48K bytes PROM 48K bytes PROM 48K bytes PROM 48K bytes Existent TTL schmitt Existent TTL schmitt Existent CMOS schmitt Existent CMOS schmitt PG4/SYNC0 pin and PG5/SYNC1 pin only - 30 - CXP872P48A Characteristics Curve IDD vs. V DD (fc = 16MHz, Ta = 25C, Typical) IDD vs. V DD (fc = 12MHz, Ta = 25C, Typical) 1/2 dividing mode 1/4 dividing mode 10 1/16 dividing mode 32kHz oscillation (instruction) SLEEP mode 10 1/2 dividing mode 1/4 dividing mode 1/16 dividing mode IDD [mA] IDD [mA] SLEEP mode 1 1 0.1 32kHz SLEEP mode 0.1 3 4 VDD [V] 5 6 3 4 VDD [V] 5 6 IDD vs. fc (VDD = 5.0V, Ta = 25C, Typical) IDD vs. fc (VDD = 3.3V, Ta = 25C, Typical) 25 1/2 dividing mode 20 25 20 IDD [mA] 15 1/4 dividing mode 10 IDD [mA] 15 1/2 dividing mode 10 1/4 dividing mode 5 1/16 dividing mode 5 1/16 dividing mode SLEEP mode 0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 SLEEP mode 12 14 16 System clock (MHz) System clock (MHz) - 31 - CXP872P48A Package Outline Unit: mm 100PIN QFP (PLASTIC) + 0.1 0.15 - 0.05 23.9 0.4 + 0.4 20.0 - 0.1 + 0.4 14.0 - 0.01 17.9 0.4 15.8 0.4 A 0.65 0.12 M + 0.35 2.75 - 0.15 0.15 0 to 15 DETAIL A 0.8 0.2 (16.3) PACKAGE STRUCTURE PACKAGE MATERIAL SONY CODE EIAJ CODE JEDEC CODE QFP-100P-L01 QFP100-P-1420-A LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT EPOXY RESIN SOLDER PLATING COPPER / 42 ALLOY 1.4g 100PIN LQFP (PLASTIC) 16.0 0.2 75 76 14.0 0.1 51 50 100 1 0.5 0.08 + 0.08 0.18 - 0.03 25 26 (0.22) + 0.2 1.5 - 0.1 + 0.05 0.127 - 0.02 0.1 0.1 0.1 0 to 10 DETAIL A 0.5 0.2 NOTE: Dimension "" does not include mold protrusion. PACKAGE STRUCTURE PACKAGE MATERIAL EPOXY/PHENOL RESIN SOLDER PLATING 42 ALLOY LEAD TREATMENT LEAD MATERIAL PACKAGE WEIGHT SONY CODE EIAJ CODE JEDEC CODE LQFP-100P-L01 QFP100-P-1414-A - 32 - 0.5 0.2 A (15.0) |
Price & Availability of CXP872P48A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |