View SP319CF_153606.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

(R)
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
s s s s s s s s s
20Mbps V.35 Data Throughput +5V-Only, Single Supply Operation 3 Drivers, 3 Receivers - V.35 4 Drivers, 4 Receivers - RS-232 Improved V.35 Receiver Propagation Delays No External V.35 Termination Resistors Required Termination Disable for V.35 80-pin QFP Surface Mount Packaging Pin Compatible with SP320
DESCRIPTION The SP319 is a complete V.35 interface transceiver offering 3 drivers and 3 receivers for V.35, and 4 drivers and 4 receivers for RS-232 (V.28). A Sipex patented charge pump allows +5V only low power operation. RS-232 drivers and receivers are specified to operate at 120kbps, all V.35 drivers and receivers operate up to 10Mbps. Typical Applications Circuit
+5V
Pinout
80 R1OUT 79 RCOUT3 78 R2OUT 77 RCB3 76 RCA3 75 NC 74 NC 73 VCC 72 GND 71 RCB1 70 RCA1 69 NC 68 R2IN 67 NC 66 R1IN 65 DRB3 64 GND 63 DRA3 62 VCC 61 DRA1
25, 33, 41, 62, 73 26 + 0.1F + 0.1F C1+ VCC VDD 27 32 + 0.1F
30 C128 C2+ 31 C2-
SP319
VSS
0.1F +
+5V
3 TS000 9 ENV35 75 ENT
Vcc 400k 100
RCA1 70 RCOUT 1 RCB1 71 RCA2 37 RCOUT2 20 RCB2 38 R1IN 66 R1OUT 80 R2IN 68 R2OUT 78 R3IN 35
5k 5k 100
14 DRIN1 61 DRA1
Vcc
400k
59 DRB1 13 T1IN
Vcc
58 T1OUT 16 T2IN
400k
Vcc
54 T2OUT 17 T3IN
400k
Vcc 400k
47 T3OUT 24 T4IN
RCOUT1 1 NC 2 TS000 3 NC 4 NC 5 TTEN 6 RTEN 7 NC 8 ENV35 9 NC 10 NC 11 NC 12 T1IN 13 DRIN1 14 DRIN3 15 T2IN 16 T3IN 17 NC 18 R3OUT 19 RCOUT2 20
SP319
60 GND 59 DRB1 58 T1OUT 57 NC 56 NC 55 NC 54 T2OUT 53 NC 52 NC 51 T4OUT 50 NC 49 NC 48 NC 47 T3OUT 46 NC 45 NC 44 DRB2 43 GND 42 DRA2 41 VCC
Vcc
51 T4OUT
R3OUT 19 R4IN 39 R4OUT 21 RCA3 76
5k 400k
42 DRA2
5k Vcc 400k
44 DRB2 23 STEN 15 DRIN3 63 DRA3 65 DRB3 6 TTEN
RCOUT3 79 RTEN 7 RCB3 77
100
29, 34, 43, 60, 64, 72
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
1
ROUT4 21 DRIN2 22 STEN 23 T4IN 24 VCC 25 C1+ 26 VDD 27 C2+ 28 GND 29 C1- 30 C2- 31 VSS 32 VCC 33 GND 34 R3IN 35 NC 36 RCA2 37 RCB2 38 R4IN 39 NC 40
22 DRIN2
(c) Copyright 2000 Sipex Corporation
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. VCC.....................................................................................................+7V Input Voltages Logic........................................................-0.3V to (VCC+0.5V) Drivers..................................................-0.3V to (VCC+0.5V) Receivers..................................................30V at 100mA Output Voltages Logic........................................................-0.3V to (VCC+0.5V) Drivers.......................................................................14V Receivers..............................................-0.3V to (VCC+0.5V) Storage Temperature.......................................................-65C to +150C Power Dissipation per Package 80-pin QFP (derate 18.3mW/oC above +70oC)..........................1500mW
SPECIFICATIONS
TAMB = TMIN to TMAX and VCC = 5V5% unless otherwise noted.
PARAMETER V.35 DRIVER TTL Input Levels VIL VIH Voltage Outputs Open Circuit Voltage Differential Outputs Source Impedance Short Circuit Impedance Voltage Output Offset AC Characteristics Transition Time Maximum Transmission Rate Propagation Delay tPHL tPLH V.35 RECEIVER TTL Output Levels VOL VOH Receiver Inputs Differential Input Threshold Input Impedance Short Circuit Impedance AC Characteristics Maximum Transmission Rate Propagation Delay tPHL tPLH
MIN.
TYP.
MAX.
UNITS
CONDITIONS
0.8 2.0 +1.2 +0.66 150 165 +0.6 40 10 80 80 100 100
Volts Volts Volts Volts Ohms Ohms Volts ns Mbps ns ns Refer to Figure 1 RL=100 from A to B; Figure 2 Figure 4 Measured from A=B to Gnd, VOUT=-2V to +2V; Figure 5; TAMB = +25oC VOffset={[|VA|+|VB|]/2}; Figure 3 TAMB = +25oC for all AC parameters 10% to 90%; Figure 6 VDIFF OUT= 0.55V+20% ; Figure 9 Measured from 1.5V of VIN to 50% of VOUT; Figure 9, 10 Measured from 1.5V of VIN to 50% of VOUT; Figure 9, 10
+0.44 50 135 -0.6
+0.55 100 150
0.4 2.4 -0.3 90 135 +0.3 110 165
Volts Volts Volts Ohms Ohms
IOUT=-3.2mA IOUT=1.0mA
100 150
Figure 7 Measured from A=B to Gnd VIN=-2V to +2V; Figure 8; TAMB = +25oC
TAMB = +25oC for all AC parameters VIN = +0.55V +20%; Figure 9 Measured from 50% of VIN to 1.5V of ROUT; Figure 9, 11 Measured from 50% of VIN to 1.5V of ROUT; Figure 9, 11
10 60 60 80 80
Mbps ns ns
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
2
SPECIFICATIONS (CONTINUED)
TAMB = TMIN to TMAX and VCC = 5V5% unless otherwise noted.
PARAMETER RS-232 DRIVER TTL Input Levels VIL VIH Voltage Outputs High Level Output Low Level Output Open Circuit Output Short Circuit Current Power Off Impedance AC Characteristics Slew Rate Maximum Transmission Rate Transition Time Propagation Delay tPHL tPLH RS-232 RECEIVER TTL Output Levels VOL VOH Receiver Input Input Voltage Range High Threshold Low Threshold Hysteresis Receiver Input Circuit Bias Input Impedance AC Characteristics Maximum Transmission Rate Propagation Delay tPHL tPLH POWER REQUIREMENTS No Load VCC Supply Current Full Load VCC Supply Current
MIN.
TYP.
MAX.
UNITS
CONDITIONS
0.8 2.0 +5.0 -15.0 -15 -100 300 +15.0 -5.0 +15 +100
Volts Volts Volts Volts Volts mA Ohms V/s kbps RL= 3k to Gnd; Figure 13 RL= 3k to Gnd; Figure 13 RL= ; Figure 12 RL= Gnd; Figure 15 VCC= 0V; VOUT= +2V; Figure 16
30 120 1.56 2 2 8 8
Figure 14
RL= 3k, CL= 2500pF Rise/fall time, between +3V RL= 3k, CL= 2500pF; Figure 17 RL= 3k, CL= 2500pF; From 1.5V of TIN to 50% of VOUT RL= 3k, CL= 2500pF; From 1.5V of TIN to 50% of VOUT
s s s
0.4 2.4 -15 0.8 0.2 3 120 0.1 0.1 40 60 1 1 70 80 1.7 1.2 0.5 5 +15 3.0 1 +2.0 7
Volts Volts Volts Volts Volts Volts Volts k kbps s s mA mA
IOUT = -3.2mA IOUT = 1.0mA
VCC= 5V; TA= +25C Figure 19 VIN= +15V; Figure 18
From 50% of RIN to 1.5V of ROUT From 50% of RIN to 1.5V of ROUT No load; VCC= 5.0V; TA= 25C RS-232 drivers RL= 3k to Gnd; DC Input V.35 drivers RL= 100 from A to B; DC Input TS000 = ENV35 = 0V
Shutdown Current
1.5
10
mA
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
3
A
A
50
V
OCA
3.9k
VOC
VOCB
VT 50 VOS
B
B
C
C
Figure 1. V.11 and V.35 Driver Output Open-Circuit Voltage
Figure 2. V.35 Driver Output Test Terminated Voltage
V1 A
A
50
50 VT 50 VOS
24kHz, 550mVp-p Sine Wave
V2
B
B
C
C
Figure 3. V.35 Driver Output Offset Voltage
Figure 4. V.35 Driver Output Source Impedance
A
A 50
Oscilloscope
B
ISC
50 B
2V
50
C
C
Figure 5. V.35 Driver Output Short-Circuit Impedance
SP319DS/08
Figure 6. V.35 Driver Output Rise/Fall Time
(c) Copyright 2000 Sipex Corporation
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
4
A
V1 A 50
24kHz, 550mVp-p Sine Wave
V2
B
Isc
B
2V
C
C
Figure 7. V.35 Receiver Input Source Impedance
Figure 8. V.35 Receiver Input Short-Circuit Impedance
CL1 TIN A B CL2
fIN (50% Duty Cycle, 2.5VP-P)
A ROUT B 15pF
Figure 9. Driver/Receiver Timing Test Circuit
f > 10MHz; tR < 10ns; tF < 10ns DRIVER INPUT +3V 1.5V 0V A B tDPLH DIFFERENTIAL OUTPUT VB - VA VO+ 0V VO- tDPHL VO 1/2VO tPLH tPHL 1/2VO 1.5V
DRIVER OUTPUT
tR
tF
tSKEW = | tDPLH - tDPHL |
Figure 10. Driver Propagation Delays
SP319DS/08 SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines (c) Copyright 2000 Sipex Corporation
5
f > 10MHz; tR < 10ns; tF < 10ns V0D2+ A-B V0D2- VOH RECEIVER OUT VOL tSKEW = | tPHL - tPLH | tPLH (VOH - VOL)/2 tPHL 0V INPUT OUTPUT (VOH - VOL)/2 0V
Figure 11. Receiver Propagation Delays
A
A
VOC
3k
VT
C
C
Figure 12. V.28 Driver Output Open Circuit Voltage
Figure 13. V.28 Driver Output Loaded Voltage
A
A
7k
VT
Oscilloscope
Isc
C
Scope used for slew rate measurement.
C
Figure 14. V.28 Driver Output Slew Rate
SP319DS/08
Figure 15. V.28 Driver Output Short-Circuit Current
(c) Copyright 2000 Sipex Corporation
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
6
VCC = 0V
A
A Ix
3k
2V
2500pF
Oscilloscope
C
C
Figure 16. V.28 Driver Output Power-Off Impedance
Figure 17. V.28 Driver Output Rise/Fall Times
A Iia
15V
A
Voc
C
C
Figure 18. V.28 Receiver Input Impedance
Figure 19. V.28 Receiver Input Open Circuit Bias
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
7
THEORY OF OPERATION The SP319 is a single chip +5V-only serial transceiver that supports all the signals necessary to implement a full V.35 interface. Three V.35 drivers and three V.35 receivers make up the clock and data signals. Four RS-232 (V.28) drivers and four RS-232 (V.28) receivers are used for control line signals for the interface. V.35 Drivers The V.35 drivers are +5V-only, low power voltage output transmitters. The drivers do not require any external resistor networks, and will meet the following requirements: 1. Source impedance in the range of 50 to 150. 2. Resistance between short-circuited terminals and ground is 150 +15. 3. When terminated with a 100 resistive load the terminal to terminal voltage will be 0.55 Volts 20% so that the A terminal is positive to the B terminal when binary 0 is transmitted, and the conditions are reversed to transmit binary 1. 4. The arithmetic mean of the voltage of the A terminal with respect to ground, and the B terminal with respect to ground will not exceed 0.6 Volts when terminated as in 3 above. The V.35 drivers can operate at data rates as high as 5Mbps. The driver outputs are protected against short-circuits between the A and B outputs and short circuits to ground. Two of the V.35 drivers, DRIN2 and DRIN3 are equipped with enable control lines. When the enable pins are high the driver outputs are disabled, the output impedance of a disabled driver will nominally be 300. When the enable pins are low, the drivers are active. V.35 Receivers The V.35 receivers are +5V only, low power differential receivers which meet the following requirements: 1. Input impedance in the range of 100 +10. 2. Resistance to ground of 150 +15, measured from short-circuited terminals.
SP319DS/08
All of the V.35 receivers can operate at data rates as high as 5Mbps. The sensitivity of the V.35 receiver inputs is +300mV. RS-232 (V.28) Drivers The RS-232 drivers are inverting transmitters, which accept either TTL or CMOS inputs and output the RS-232 signals with an inverted sense relative to the input logic levels. Typically, the RS-232 output voltage swing is +9V with no load, and +5V minimum with full load. The transmitter outputs are protected against infinite short-circuits to ground without degradation in reliability. In the power off state, the output impedance of the RS-232 drivers will be greater than 300 over a +2V range. Should the input of a driver be left open, an internal 400k pullup resistor to VCC forces the input high, thus committing the output to a low state. The slew rate of the transmitter output is internally limited to a maximum of 30V/s in order to meet the EIA standards. The RS-232 drivers are rated for 120kbps data rates. RS-232 (V.28) Receivers The RS-232 receivers convert RS-232 input signals to inverted TTL signals. Each of the four receivers features 500mV of hysteresis margin to minimize the effects of noisy transmission lines. The inputs also have a 5k resistor to ground; in an open circuit situation the input of the receiver will be forced low, committing the output to a logic high state. The input resistance will maintain 3k-7k over a +15V range. The maximum operating voltage range for the receiver is +30V, under these conditions the input current to the receiver must be limited to less than 100mA. The RS-232 receivers can operate to beyond 120kbps. CHARGE PUMP The charge pump is a Sipex patented design (U.S. 5,306,954) that uses an innovative approach. The charge pump, with four external capacitors, uses a four-phase voltage shifting technique to attain a symmetrical +10V power supply. The capacitors can be as low as 0.1F with a 16 Volt rating. Either polarized or non-polarized capacitors can be used.
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
8
+10V a) C2+ GND GND b) C2- -10V
Since both V+ and V- are separately generated from Vcc in a no load condition, V+and V- will be symmetrical. Older charge pump approaches that generate V- from V+ will show a decrease in the magnitude of V- compared to V+ due to the inherent inefficiencies in design. The clock rate for the charge pump typically operates at 15kHz with 0.1F, 16V external capacitors. Shutdown Mode The SP319 can be put into a low power shutdown mode by bringing both TS000 (pin 3) and ENV35 (pin 9) low. In shutdown mode, SP319 draws less than 2mA. For normal operation, both pins should be connected to +5V. Termination Enable The SP319 includes a termination enable pin that connects or disconnects the receiver input termination circuitry. A TTL logic LOW at ENT (pin 75) will connect the "Y" termination network to the V.35 receiver inputs. A TTL logic HIGH at ENT (pin 75) will disconnect the "Y" termination network and the receivers will operate as V.11 compliant receivers. The ENT pin has an internal pull-down resistor so that a floating input will enable the termination network. The SP319 is compatible with the SP320 since pin 75 on the SP320 is designated as a no connect. External Power Supplies For applications where separate external supplies can be applied at the V+ and V- pins. The value of the external supply voltages should not exceed +10V. It is critical the external power supplies provide a power supply sequence of : +10V, +5V, and then -10V. Applications Information The SP319 is a single chip device that can implement a complete V.35 interface. Three (3) V.35 drivers and three (3) V.35 receivers are used for clock and data signals and four (4) RS-232 (V.28) drivers and four (4) RS-232 (V.28) receivers can be used for the control signals of the interface. Figures 25 and 28 show the SP319 configured in DTE and DCE applications along with an ISO-2593 pin out.
Figure 20. Charge Pump Waveforms
Figure 20 shows the waveforms on the positive and negative sides of capacitor C2 respectively. A free-running oscillator controls the four phases of the voltage shifting. A description of each phase follows. Phase 1: VSS Charge Storage (Figure 21) During this phase of the clock cycle, the positive side of capacitors C1 and C2 are charged to +5V. C1+ is switched to ground and the charge on C1- is transferred to C2-. Since C2+ is connected to +5V, the voltage potential across capacitor C2 becomes 10V. Phase 2: VSS Transfer (Figure 22) Phase two of the clock connects the negative terminal of C2 to the Vss storage capacitor and the positive terminal of C2 to ground, and transfers the generated -10V to C3. Simultaneously, the positive side of capacitor C1 is switched to +5V and the negative side is connected to ground. Phase 3: VDD Charge Storage (Figure 23) The third phase of the clock is identical to the first phase - the transferred charge on C1 produces -5V on the negative terminal of C1, which is applied to the negative side of capacitor C2. Since C2+ is at +5V, the voltage potential across C2 is +10V. Phase 4: VDD Transfer (Figure 24) The fourth phase of the clock connects the negative terminal of C2 to ground and transfers the generated +10V across C2 to C4, the Vdd storage capacitor. The positive side of capacitor C1 is switched to +5V and the negative side is connected to ground, and the cycle begins again.
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
9
VCC = +5V
VCC = +5V
+10V C1
+ -
C4
+ - +
+5V
C4
+ - +
C2
+ - -
VDD Storage Capacitor VSS Storage Capacitor
C1
+ -
C2
+ - -
VDD Storage Capacitor VSS Storage Capacitor
C3
-5V
-5V
C3
Figure 21. Charge Pump Phase 1
Figure 22. Charge Pump Phase 2
VCC = +5V
VCC = +5V
C4
+ - +
+5V VDD Storage Capacitor C1 VSS Storage Capacitor
+ -
C4
+ - +
C1
+ -
C2
+ - -
C2
+ - -
VDD Storage Capacitor VSS Storage Capacitor
-10V
C3
-5V
-5V
C3
Figure 23. Charge Pump Phase 3
Figure 24. Charge Pump Phase 4
+5V 0.1F 1N5819 0.1F 0.1F
+5V 1N5819 0.1F
0.1F 31
C2-
0.1F 31
C2-
28
C2+
25
VCC
27 26 30
VDD C1+ C1- 32 VSS
28 0.1F
C2+
25
VCC
27 26 30
VDD C1+ C1- 32 VSS
0.1F
SP319CF
DRIN1 14
SP319CF
P S U W A A
RCOUT3 79
TxD (103)
P S U W
RCOUT1 14
TxC (113)
DRIN3 15 DRIN2 22 RCOUT3 79 RCOUT2 20 RCOUT1 1 T2IN 16 T1IN 13 T3IN 17 T4IN 24 R2OUT 78
RCOUT2 20
Y AA X V T R H
TxCC (114) RxC (115) RxD (104)
Y AA X V T R
DRIN3 15 DRIN1 14 R2OUT 78 R1OUT 80 R4OUT 21 R3OUT 19 T2IN 16 T1IN 13 T3IN 17 T4IN 24 DRIN2 22
DTR (108) RTS (105) RL (140) LL (141) DSR (107) CTS (106) DCD (109) TM (142)
B B
H
C
C
N
N
L
L
E
E
R1OUT 80 R3OUT 19 R4OUT 21
D
D
F
F
NN
NN
29, 34, 43, 60, 64, 72
ISO2593 34-PIN DTE/DCE INTERFACE CONNECTOR
ISO2593 34-PIN DTE/DCE INTERFACE CONNECTOR
29, 34, 43, 60, 64, 72
Figure 25. Typical DTE-DCE V.35 Connection using the SP319
SP319DS/08 SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines (c) Copyright 2000 Sipex Corporation
10
Signal Ground Clear to Send Data Carrier Detect Ring Indicator Local Loopback Remote Loopback Receive Data (A) Receive Data (B) Receive Timing (A) Receive Timing (B) Unassigned--Unassigned--Unassigned--Unassigned--Unassigned--Unassigned--Test Mode
B D F J L N R T V X Z BB DD FF JJ LL NN
A C E H K M P S U W Y AA CC EE HH KK MM
Chasis Ground Request to Send DCE Ready (DSR) DTE Ready (DTR) Unassigned--Unassigned--Transmitted Data (A) Transmitted Data (B) Terminal Timing (A) } 113(A) Terminal Timing (B) } 113(B) Transmit Timing (A) } 114(A) Transmit Timing (B) } 114(B) Unassigned--Unassigned--Unassigned--Unassigned--Unassigned---
Figure 26. ISO-2593 Connector Pin Out
+5V
25, 33, 41, 62, 73 26 + 0.1F + 0.1F 30 C1+ VCC VDD 27 32 + 0.1F
C128 C2+ 31 C23 TS000 9 ENV35
SP319
VSS
0.1F +
+5V
75 ENT
Vcc 400K 100
103(A) TXD 103(B) 113(A) TXC 113(B) 105 RTS 108 DTR 140 RLPBK 141 LLPBK SPARE SPARE SPARE
RCA1 70 RCOUT 1 RCB1 71 RCA2 37 RCOUT2 20 RCB2 38 R1IN 66 R1OUT 80 R2IN 68 R2OUT 78 R3IN 35
5k 5k 100
14 DRIN1 61 DRA1 59 DRB1 13 T1IN
RXD 104(A) 104(B) CTS 106 DSR 107 DCD 109 RI 125 TXCC 114(A) 114(B) RXC 115(A) 115(B)
Vcc 400k
Vcc 400k
58 T1OUT 16 T2IN
Vcc
54 T2OUT 17 T3IN
400k
Vcc 400k
47 T3OUT 24 T4IN 51 T4OUT
Vcc
R3OUT 19 R4IN 39 R4OUT 21 RCA3 76
5k 400k
22 DRIN2 42 DRA2 44 DRB2 23 STEN 15 DRIN3 63 DRA3 65 DRB3 6 TTEN
5k Vcc 400k
RCOUT3 79 RTEN 7 RCB3 77
100
29, 34, 43, 60, 64, 72
Figure 27. Typical DCE V.35 Interface
SP319DS/08 SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines (c) Copyright 2000 Sipex Corporation
11
+5V
25, 33, 41, 62, 73 26 + 0.1F + 0.1F 30 C1+ VCC VDD 27 32 + 0.1F
C128 C2+ 31 C23 TS000 9 ENV35
SP319
VSS
0.1F +
+5V
75 ENT
Vcc 400k 100
104(A) RXD 104(B) 114(A) TXCC 114(B) 106 CTS 107 DSR 109 DCD 125 RI 115(A) RXC 115(B)
RCA1 70 RCOUT 1 RCB1 71 RCA2 37 RCOUT2 20 RCB2 38 R1IN 66 R1OUT 80 R2IN 68 R2OUT 78 R3IN 35
5k 5k 100
14 DRIN1
Vcc
TXD 103(A) 103(B) RTS 105 DTR 108 RLPBK 140 LLPBK 141 TXCT 113(A) 113(B) SPARE SPARE SPARE
61 DRA1 59 DRB1 13 T1IN
400k
Vcc 400k
58 T1OUT 16 T2IN
Vcc 400k
54 T2OUT 17 T3IN
Vcc 400k
47 T3OUT 24 T4IN 51 T4OUT
Vcc
R3OUT 19 R4IN 39 R4OUT 21 RCA3 76
5k 400k
22 DRIN2 42 DRA2 44 DRB2 23 STEN 15 DRIN3 63 DRA3 65 DRB3 6 TTEN
5k Vcc 400k
RCOUT3 79 RTEN 7 RCB3 77
100
29, 34, 43, 60, 64, 72
Figure 28. Typical DTE V.35 Interface
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
12
PACKAGE:
D D1
QUAD FLATPACK JEDEC "BE-2" OUTLINE
0.3" RAD. TYP. PIN 1 0.2" RAD. TYP.
C L
E1 E 64
10-16
0-7 0.005/0.009" (0.13/0.23) C L A 0.009"/0.015" (0.220/0.380) 0.02559"/- (0.65/-) A1 Seating Plane L 10-16
DIMENSIONS in Inches JEDEC BE-2 Outline Minimum/Maximum 80-PIN (mm) A A1 D D1 E E1 L -/0.0925 (-/2.350) -/0.010 (-/0.250) 0.667/0.687 (16.950/17.450) 0.547/0.555 (13.900/14.100) 0.667/0.687 (16.950/17.450) 0.547/0.555 (13.900/14.100) 0.0255/0.0375 (0.650/0.950)
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
13
ORDERING INFORMATION
Model Temperature Range Package Types SP319CF ..................................................... 0C to +70C ......................... 80-pin JEDEC (BE-2 Outline) QFP
Please consult the factory for pricing and availability on a Tape-On-Reel option.
Corporation
SIGNAL PROCESSING EXCELLENCE
Sipex Corporation Headquarters and Sales Office 22 Linnell Circle Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: sales@sipex.com Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others.
SP319DS/08
SP319 20Mbps, +5V-Only V.35 Interface with RS-232 (V.28) Control Lines
(c) Copyright 2000 Sipex Corporation
14

▲Up To Search▲

Price & Availability of SP319CF

	To Download SP319CF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .