View AN8016_189995.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Voltage Regulators
AN8016NSH
Single-channel 1.8-volt step-up DC-DC converter control IC
s Overview
The AN8016NSH is a single-channel PWM DC-DC converter control IC that supports low-voltage operation. This IC allows a stepped-up voltage output to be provided with a minimal number of external components. It features a low minimum operating voltage of 1.8 V, and due to being provided in a 10-pin surface mount package with a 0.5 mm lead pitch, is optimal for use in miniature high-efficiency power supplies for portable equipment.
Unit: mm
0.5
5
6
0.10.1
0.6250.10
0.50.2 4.30.30
* Wide operating supply voltage range: 1.8 V to 14 V 6.30.30 * High-precision reference voltage circuit: 1.27 V (allowance: 3%) SSOP010-P-0225 * Supports control over a wide output frequency range: 20 kHz to 1 MHz * Provides a fixed output current with minimal supply voltage fluctuations by using an external resistor to set the output current with a totem pole structure in the output block. * Large maximum output current of 50 mA * Timer latch short-circuit protection circuit (charge current: 1.3 A typical) * Low input voltage malfunction prevention circuit (U.V.L.O.) (circuit operation start voltage: 1.6 V typical) * On/off control function (active-high, standby current: 5 A maximum) * Fixed maximum duty ratio with small sample-to-sample variations (80% 5%) * Adjustable soft start time provided by using separate DTC and S.C.P. pins. * Adopts a 0.5 mm lead pitch 10 pin SO flat package (SSONF-10D) * Adopts techniques for reducing noise, increasing the light load efficiency, and suppressing the maximum base current when turning on the npn transistor used as the external switching element.
s Applications
* LCD displays, digital still cameras, PDAs
0.15-0.05
s Features
0.6250.10
+0.1
1.50.2
3.00.30
1
10
0.20.1
1
AN8016NSH
s Block Diagram
OSC VCC
Voltage Regulators
Active-high
5
9
Off FB IN-
4 10 1
On/off control
Reference voltage supply 1.27 V
Triangular wave generator
0.7 V 0.2 V VCC 8 RB
SS pin
U.V.L.O. Error amp. 1.27 V VCC 1 A
Latch
PWM 6 0.6 V 30 k Out
Low level detector comp. Low level clamp
R S 1.27 V
Q VCC
High level detector comp.
0.23 V
5 A
Low level clamp
Unlatch comp. 0.23 V 1.27 V S.C.P. comp.
7
GND
2
s Pin Descriptions
Pin No. 1 2 3 4 5 6 7 8 9 10 Symbol IN- S.C.P. SS Off VCC Out GND RB OSC FB Description Error amplifier inverting input Time constant capacitor connection for short-circuit protection Soft-start time-constant capacitor connection On/off control Supply voltage Push-pull output Ground Output-current setting resistor connection pin Oscillator circuit timing resistor/capacitor connection pin Error amplifier output
3
S.C.P.
SS
3
Voltage Regulators
s Absolute Maximum Ratings
Parameter Supply voltage Off pin allowable application voltage IN- pin allowable application voltage Out pin allowable application voltage Supply current Output source current Output sink current Power dissipation
*
AN8016NSH
Symbol VCC VOFF VIN- VOUT ICC ISO(OUT) ISI(OUT) PD Topr Tstg
Rating 15 15 VCC 15 -50 +50 115 -30 to +85 -55 to +150
Unit V V V V mA mA mA mW C C
Operating temperature Storage temperature
Note) 1. Currents or voltages may not be applied to any pins not stipulated above. For circuit currents, a positive (+) value indicates current flowing into the IC, and a negative (-) value indicates current flowing out of the IC. 2. Items other than the storage temperature, operating temperature, and power dissipation are all stipulated at Ta = 25C. 3. *: Ta = 85C. For the independent IC without a heat sink. Note that the relationship between IC power dissipation and the ambient temperature must follow the derating curve.
s Recommended Operating Range
Parameter Supply voltage Off control pin voltage Output source current Output sink current Timing resistance Timing capacitance Oscillator frequency Short-circuit protection time constant setting capacitance Output current setting resistance RB 0 to 10k Symbol VCC VOFF ISO(OUT) ISI(OUT) RT CT fOUT CSCP Conditions 1.8 to 14 0 to 14 -40 (min.) 40 (max.) 3 to 30 100 to 10 000 20 to 1 000 1 000 (min.) Unit V V mA mA k pF kHz pF
3
AN8016NSH
s Electrical Characteristics at VCC = 2.4 V, Ta = 25C
Parameter U.V.L.O. block Circuit operation start voltage Error amplifier block Input threshold voltage Line regulation with input fluctuation Input bias current High-level output voltage Low-level output voltage PWM comparator block Output source current Output block Oscillator frequency Maximum duty High-level output voltage Low-level output voltage Output source current Output sink current Pull-down resistor Unlatch circuit block Input threshold voltage VTHUL fOUT Dumax VOH VOL ISO(OUT) ISI(OUT) RO IO = -15 mA, RB = 390 IO = 10 mA, RB = 390 VO = 0.9 V, RB = 390 VO = 0.3 V, RB = 390 RT = 12 k, CT = 330 pF ISS VSS = 0.5 V VTH VdV IB VEH VEL Voltage follower VCC = 1.8 V to 14 V VUON Symbol Conditions
Voltage Regulators
Min
Typ
Max
Unit
1.45
1.6
1.75
V
1.23 1.85 -3.5
1.27 1.0 0.2 2.0 -5
1.31 10 1.0 2.15 0.2 -6.5
V mV A V V A
170 75 1.4 -45 20 20
190 80 -32 30
210 85 0.2 -20 40
kHz % V V mA mA k
0.13
0.20
0.27
V
Short-circuit protection circuit block Input threshold voltage Input standby voltage Input latch voltage Charge current On/off control block Input threshold voltage Off mode SS pin voltage Off mode S.C.P. pin voltage Whole device Average consumption current ICC(AV) RB = 390 , Duty = 50% RB = 390 3.4 1.8 5.0 2.4 5 mA mA A VON(TH) VOFF(SS) VOFF(SCP) 0.8 0.13 0.13 1.0 1.3 0.27 0.27 V V V VTHPC VSTBY VIN ICHG VSCP = 0.5 V 1.17 -1.65 1.27 60 40 1.37 120 120 V mV mV A
-1.3 - 0.95
Latch mode consumption current ICC(LA) Standby mode current ICC(SB)
5
Voltage Regulators
s Electrical Characteristics at VCC = 2.4 V, Ta = 25C (continued)
* Design reference data
AN8016NSH
Note) The characteristics listed below are theoretical values based on the IC design and are not guaranteed.
Parameter U.V.L.O. block Reset voltage Error amplifier block VTH temperature characteristics Output source current Output sink current Open-loop gain PWM comparator block SS pin voltage Output block RB pin voltage Oscillator frequency supply voltage characteristics Oscillator frequency temperature characteristics
Symbol
Conditions
Min
Typ
Max
Unit
VR Ta = -30C to +85C VFB = 0.5 V VFB = 0.5 V - 0.5
0.8 + 0.5 -40 2 80
V
VTHdT ISO(FB) ISI(FB) AV
% A mA dB
VSS RB = 390 VCC = 1.8 V to 14 V Ta = -30C to 85C -1 -3
1.22
V
VB fdV fdT
0.13 +1 +3
V % %
Short-circuit protection circuit block Comparator threshold voltage On/off control block On/Off pin current IOFF VOFF = 1.5 V 23 A VTHL 1.27 V
5
AN8016NSH
s Terminal Equivalent Circuits
Pin No. 1 Equivalent Circuit Description IN-: Error amplifier inverting input.
Voltage Regulators
I/O I
VCC
1
300 1.26 V
2
VCC
Latch
0.23 V 3 k 3 k 2 1.27 V
S R
Q
Output cutoff To the on/off control circuit
0.23 V
Low level detection comp.
S.C.P.: Connection for the capacitor that sets the timer latch short-circuit protection circuit time constant. Use a capacitor with a value of 1 000 pF or higher. The charge current ICHG is 1.3 A (typical). However, the capacitor is charged with a time constant determined by 0.23 V and a resistance of 6 k until the pin voltage reaches 0.23 V. SS: Connection pin for the capacitor that determines the PWM output soft start period. Note that the the short-circuit protection circuit does not supply charge current to S.C.P. pin until this pin voltage reaches about 0.2 V. The source current ISS is 5 A (typical). However, the capacitor is charged with a time constant determined by 0.23 V and a resistor of 6 k until the pin voltage reaches 0.23 V. Off: This pin controls the on/off for the IC. High-level input: normal operation (VOFF > 1.3 V) Low-level input: standby mode (VOFF < 0.8 V) In the standby state, the total IC current consumption is decreased to 5 A or under. VCC: Power supply connection. Provide an operating supply voltage of 1.8 V to 14 V.
O
3
VCC CT PWM Unlatch comp.
To the on/off control circuit
I
0.23 V 3 k 3 k 3
0.23 V
S.C.P. pin
4
Internal circuit start/stop
I
30 k 4 60 k
5 5
7
Voltage Regulators
s Terminal Equivalent Circuits (continued)
Pin No. 6 Equivalent Circuit
VCC RB IO(SO) 6 30 k
AN8016NSH
Description Out: This is a push-pull output. The absolute maximum rating for the output current is 50 mA. A constant-current output with excellent line regulation and minimal sample-to-sample variations can be acquired by connected an external resistor to the RB pin.
I/O O
7
7
GND: IC ground.
8
VCC
Out R1 8
9
VCC
Latch
RB: Connection for the resistor that sets the output current. Use a resistor in the range 0 to 10 k. Note that the internal resistor R1 has a value of 1.0 k. Thus the pin voltage will be 0.13 V when RB is 390 . OSC: Connection for the capacitor and resistor that determines the oscillator frequency. Use a capacitor in the range 100 pF to 10 000 pF and a resistor in the range 3 k to 30 k. Use an oscillator frequency in the range 20 kHz to 1 MHz. FB: Error amplifier output. A source current is about -40 A and a sink current is about 2 mA. Correct the gain and the phase frequency characteristics by inserting a capacitor and a resistor between this pin and IN- pin.
I
O
S R 0.23 V 9
Q
10
VCC 40 A C 2 mA 10 PWM
O
7
AN8016NSH
s Usage Notes
Voltage Regulators
* Notes on IC power dissipation Since the power dissipation in this IC increases proportionally with the supply voltage, applications must be careful to operate so that the actual power dissipation does not exceed the power dissipation. Since the output current set by the application circuit flows in the IC during the period corresponding to the output on duty factor (Du, where Dumax is 0.85), the IC power dissipation P is given by the following formula. P = (VCC - VBEQ1) x IOUT x Du + VCC x ICC < PD
s Application Notes
[1] Power dissipation for the SSOP010-P-0225 package PD T a
400 386 Glass epoxy printed circuit board (50 x 50 x t0.8 mm3) Rth(j-a) = 259C/W
300 287
Power dissipation PD (mW)
Independent IC without a heat sink
Rth(j-a) = 348C/W 200
154 115 100
0 0 25 50 75 85 100 125 150
Ambient temperature Ta (C)
9
Voltage Regulators
s Application Notes (continued)
[2] Main characteristics Timing capacitance Oscillator frequency
1 000
95
AN8016NSH
Maximum duty Oscillator frequency
RT = 3 k
90
Oscillator frequency (kHz)
Maximum duty (%)
RT = 6.2 k
RT = 3 k RT = 6.2 k
85 RT = 12 k 80 RT = 30 k 75
100
RT = 12 k RT = 30 k 10 100 1 000 10 000
70 10 100 1 000
Timing capacitance (pF)
Oscillator frequency (kHz)
Error amplifier VTH temperature characteristics
1.28
Oscillator frequency temperature characteristics
192
190
Oscillator frequency (kHz)
-30 -10
1.278
188
Voltage (V)
1.276
186
184
1.274
182
1.272
180 10 30 50 70 90
-30
-10
10
30
50
70
90
Ambient temperature Ta (C)
Ambient temperature Ta (C)
Maximum duty temperature characteristics
81
80
Maximum duty (%)
79
78
77
76
-30
-10
10
30
50
70
90
Ambient temperature Ta (C)
9
AN8016NSH
s Application Notes (continued)
[3] Timing charts (internal waveforms)
Voltage Regulators
High Off pin voltage Low 2.4 V Supply voltage (VCC) Error amplifier output (FB) S.C.P. pin voltage Power on SS pin voltage Triangular wave (CT) 2.0 V 1.27 V 1.22 V 0.7 V 0.6 V 0.4 V 0.2 V High Out pin waveform Low Soft start operation Maximum duty: 80%
Figure 1. PWM comparator operating waveforms
2.0 V Short-circuit protection comparator threshold level Dead time voltage (VDT) Error amplifier output (FB) Triangular wave (CT) Out pin waveform Low 1.27 V S.C.P. pin voltage Short-circuit protection comparator output tPE 0.06 V High Low Figure 2. Short-circuit protection operating waveforms High 1.27 V
0.6 V
11
Voltage Regulators
s Application Notes (continued)
[4] Functional descriptions
AN8016NSH
1. Reference voltage block This circuit is composed of a band gap circuit, and outputs a 1.26-volt temperature compensated reference voltage. This reference voltage is stabilized when the supply voltage is 1.8 V or higher. 2. Triangular wave generator This circuit generates a triangular wave like sawtooth with a peak of 0.75 V and a trough of 0.2 V using a capacitor (for the time constant) and resistor connected to the OSC pin (pin 9). The oscillator frequency can be set to any value by selecting appropriate values for the external capacitor and resistor, CT and RT. This oscillator can provide a frequency in the range 20 kHz to 1 MHz. The triangular wave signal is provided to the inverting input of the PWM comparator internally to the IC. Use the formulas below for rough calculation of the oscillator frequency. 1 CT x RT x ln VOSCL VOSCH 1 [Hz] CT x RT
VOSCH 0.75 V
VOSCL 0.2 V t1 Rapid charge t2 Discharge T
Figure 1. Triangular oscillator waveform
fOSC -
0.75 x
Note, however, that the above formulas do not take the rapid charge time, overshoot, and undershoot into account. See the experimentally determined graph of the oscillator frequency vs. timing capacitance value provided in the main characteristics section. 3. Error amplifier This circuit is an npn-transistor input error amplifier that detects and amplifies the DC-DC converter output voltage, and inputs that signal to a PWM comparator. The 1.27 V internal reference voltage is applied to the noninverting input. Arbitrary gain and phase compensation can be set up by inserting a resistor and capacitor in series between the error amplifier output pin (pin 10) and the inverting input pin (pin 1). The output voltage VOUT can be set by resistor-dividing the output as shown in figure 2.
VOUT = 1.27 x VOUT R1 R2 FB 10
R1 + R2 R2
IN- 1
Error amplifier 1.27 V To the PWM comparator input
Figure 2. Connection method of error amplifier
11
AN8016NSH
s Application Notes (continued)
[4] Function descriptions (continued)
Voltage Regulators
4. Timer latch short-circuit protection circuit This circuit protects the external main switching element, flywheel diode, choke coil, and other components against degradation or destruction if an excessive load or a short circuit of the power supply output continues for longer than a certain fixed period. The timer latch short-circuit protection circuit detects the output of the error amplifiers. If the DC-DC converter output voltage drops and an error amplifier output level exceeds 1.27 V, this circuit outputs a low level and the timer circuit starts. This starts charging the external protection circuit delay time capacitor. If the error amplifier output does not return to the normal voltage range before that capacitor reaches 1.27 V, the latch circuit latches, the output drive transistors are turned off, and the off-period is set to 100%. 5. Low input voltage malfunction prevention circuit (U.V.L.O.) This circuit protects the system against degradation or destruction due to incorrect control operation when the power supply voltage falls during power on or power off. The low input voltage malfunction prevention circuit detects the internal reference voltage that changes with the supply voltage level. While the supply voltage is rising, this circuit cuts off the output drive transistor until the reference voltage reaches 1.6 V. It also sets the off-period to 100%, and at the same time holds the S.C.P. pin (pin 2) and the SS pin (pin 3) at the low level. 6. PWM comparator The PWM comparator controls the on-period of the output pulse according to its input voltage. The output transistors are turned on during periods when the OSC pin (pin 9) triangular waveform is lower than the error amplifier output pin (pin 10), the SS pin (pin 3), and the IC internally fixed dead-time voltage (about 0.6 V). The maximum duty is fixed at 80% (typical). The SS pin provides a constant-current source output of 5 A (typical), and can be used to implement soft start operation in which the output pulse on period is gradually increased by connecting an external capacitor to that pin. Note that the SS pin charge operation completes when the SS pin voltage reaches 1.22 V (typical). 7. Unlatch block The unlatch circuit holds the S.C.P. fixed at the low level while the SS pin voltage reaches the soft start operation start-level (about 0.23 V) when power is first applied. This suppresses increases in the short-circuit protection detection time associated with longer startup times. 8. Output block The output circuit has a totem pole structure. A constant-current source output with good line regulation can be set up at an arbitrary voltage by connecting a current setting resistor to the RB pin. This circuit can provide an output current of up to 50 mA. The output pin has a breakdown voltage of 15 V. 9. On/off control block The IC can be turned on or off externally. When the Off pin (pin 4) voltage is set by the application of about 1.3 V or higher, the internal reference voltage is turned on, and control operation starts. If the Off pin voltage is dropped to about 0.8 V or lower, after the S.C.P. pin and SS pin external capacitors discharge, the internal reference voltage is turned off and IC control operation is stopped. This reduces IC current consumption to 5 A or under.
13
Voltage Regulators
s Application Notes (continued)
AN8016NSH
[5] Time constant setup for the timer latch short-circuit protection circuit Figure 4 shows the structure of the timer latch short-circuit protection circuit. The short-circuit protection comparator continuously compares a 1.27 V reference voltage with the error amplifier output VFB. When the DC-DC converter output load conditions are stable, the short-circuit protection comparator holds its average value, since there are no fluctuations in the error amplifier outputs. At this time, the output transistor Q1 will be in the conducting state, and the S.C.P. pin will be held at about 60 mV. If the output load conditions change rapidly and a high-level signal (1.27 V or higher) is input to the shortcircuit protection comparator's non-inverting input from the error amplifier, the short-circuit protection comparator will output a low level and the output transistor Q1 will shut off. Then, the external capacitor CS connected to the S.C.P. pin will start to charge. When the external capacitor CS is charged to about 1.27 V, the latch circuit will latch and the off-period will be set to 100% with the output held fixed at the low level. Once the latch circuit has latched, the S.C.P. pin capacitor will be discharged to about 40 mV, but the latch circuit will not reset unless either power is turned off or the power supply is restarted using on/off control. The capacitor CS is charged from 60 mV to about 230 mV with a time constant determined by a resistor of 6 k, and is charged from 230 mV to 1.26 V by a constant current of about 1.3 A. 1) 0.06 VSCP [V] 0.23 VSCP = (0.23 - 0.06) x {1 - exp( - tPE1 [s] 0.017 x CS [mF] 2) 0.23 VSCP [V] 1.26 1.27 V = 0.23 V + ICHG x tPE2 [s] 0.80 x CS [F] tPE2 CS
0.23 0.06 tPE1 tPE2 t [s]
tPE1 )} [V] 6k * CS
VSCP [V] Short-circuit detection time tPE
1.27
tPE [s] tPE1 + tPE2 0.817 x CS [F]
Figure 3. S.C.P. pin charging waveform
On/off control
Internal reference VCC 1 A 0.23 V 3 k Latch R S Q Output shutoff U.V.L.O.
FB 10 IN- 1 3 k Error amp. S.C.P. comp. 1.27 V 1.27 V
High level detection comparator 1.27 V
Q1 S.C.P. 2
CS
Figure 4. Short-circuit protection circuit
At power supply startup, the output appears to be in the shorted state, the error amplifier output goes to the high level, and the IC starts to charge the S.C.P. pin capacitor. Therefore, users must select an external capacitor that allows the DC-DC converter output voltage to rise before the latch circuit in the later stage latches. In particular, care is required if the soft start function is used, since that function makes the startup time longer. 13
AN8016NSH
s Application Notes (continued)
Voltage Regulators
[6] Setting the soft start time A soft start function, which gradually increases the width of the output pulses at power on, will be applied if a capacitor is connected to the SS pin. This can prevent rush currents and overshoot when the power supply is turned on. The capacitor CSS is charged from 60 mV to about 230 mV with a time constant determined by a resistor of 6 k, and is charged from 230 mV to 1.22 V by a constant current of about 5 A. The following formulas express the soft start time for the duty of up to 50%. 1) 0.06 VSCP [V] 0.23 VSCP = (0.23 - 0.06) x {1 - exp( - tPE1 [s] 0.017 x CS [mF] 2) 0.23 VSCP [V] 1.26 0.52 V = 0.23 V + ICHG x tPE2 [s] 0.058 x CS [F] tSS2 CS tSS1 )} [V] 6k * CS
tSS [s] tSS1 + tSS2 0.075 x CS [F]
FB (V) 1.22 OSC SS
0.75 0.52 0.23 0.06
tSS1
tSS2
t (s) Duty: 50%
Soft start time DC-DC converter output voltage
Figure 5. Soft start operating waveforms
15
Voltage Regulators
s Application Notes (continued)
AN8016NSH
[7] Parallel synchronous operation of multiple ICs Multiple instances of this IC can be operated in parallel. All the ICs will operate at the same frequency if the master and slave IC OSC pins (pin 9) are connected directly. 1. Notes on S.C.P. operation during parallel operation In the circuit in figure 6, if either the IC operating in master mode or the IC in slave mode detects a short circuit, the IC that detected the short circuit will enter latched mode. The latched mode state is a state in which the output is shut off and both the RB pin and the SS pin are set to the low level. However in this mode, this IC has an added function that holds the OSC pin at the high level (about 0.8 V). When OSC pin of the IC that did not enter latched mode goes to the high level, the internally fixed dead- time voltage (about 0.6 V) will then be lower than the OSC pin voltage, and internal PWM circuit output will stop. That will cause this IC to go to the output shorted state, and then, this IC will also switch to latched mode. Therefore, applications that require parallel synchronous operation should adopt the basic circuit structure shown in figure 6. 2. Usage notes 1) If capacitors are shared as shown in figure 7 to reduce the number of external components: * The charge current will be doubled. * The short-circuit protection circuit will not operate if the S.C.P. pin capacitor is shared. In this circuit, even if the master IC detects a short circuit, the slave IC will not detect that state, so the S.C.P. pin will remain fixed at the low level state. Note that as a result, the short-circuit protection circuit will not operate and the IC will continue to operate at the maximum duty drive.
OSC
OSC
10
10
10
10
9
8
7
6
9
8
7
6
9
8
7
6
9
8 3
7 4
SS
AN8016NSH Master
AN8016NSH Slave
AN8016NSH Master
AN8016NSH Slave
1
1
1
2
3
4
5
2
3
4
5
2
3
4
5
1
2
S.C.P.
SS
S.C.P.
SS
S.C.P. NG
Figure 6. Slave operation circuit example
Figure 7. Slave operation circuit example
2)
Note that it is not possible to operate this IC (the AN8016NSH) with the two-channel AN8017SA/AN8018SA together in parallel synchronous mode.
5
6
15
AN8016NSH
s Application Circuit Examples
[1] Application circuit (Step-up circuit) VIN 3V
Voltage Regulators
SBD 47 H MA2Q738 (MA738)
VOUT 5V 200 mA
330 pF 0.1 F
12 k 390
Q1 7 GND 9 OSC 6 Out 8 RB
10 F
1 k 10 FB
2SD2408
AN8016NSH
S.C.P. 2
IN- 1
SS 3
Off 4
333 pF 103 pF 1.5 V
VCC 5 1 F
6.8 k 20 k Note) : Former part number The figure shows a step-up circuit that converts a 3 V input to a 5 V output. The AN8016NSH output stage has a totem pole circuit configuration, and can directly drive an n-channel MOSFET while minimizes switching loss and increasing efficiency. In this case, replace the npn transistor with an n-channel MOSFET in above circuit.
[2] Notes on direct n-channel MOSFET drive
1. Select an n-channel MOSFET with a low input capacitance. The AN8016NSH was designed to drive bipolar transistors, and adopts a circuit structure that can provide a constant-current (50 mA maximum) output source current. Furthermore, it has a sink current capacity of about 50 mA. This means that designs must be concerned about increased power dissipation due to increased rise and fall times. If problems occur, an inverter may be inserted as shown in figure 1 to provide amplification. 2. Use an n-channel MOSFET of a low gate threshold voltage. Since the AN8016NSH Out pin high-level output voltage is VCC - 1.0 V (minimum), a low VT MOSFET with an adequately low on-resistance must be used. Also, if a large VGS is required, one solution is to use a transformer as shown in figure 2, and apply a voltage of twice the input voltage to the IC's VCC pin.
VIN 6 Out SBD VOUT
Figure 1. Output boosting circuit
VIN
SBD
VOUT
VCC 5 6 Out
SBD
VCC 2 x VIN - VD Figure 2. Gate drive voltage boosting technique
17
Voltage Regulators
s Application Circuit Examples (continued)
[2] Notes on direct n-channel MOSFET drive (continued)
AN8016NSH
3. Notes on printed circuit board pattern layout Observe the following recommendations on printed circuit board pattern layout to achieve low noise and high efficiency. 1) Use extremely wide lines for the ground lines, and isolate the IC ground from the power system ground. 2) 3) 4) 5) Make the lines in the high-current system as wide as possible. Position the input filter capacitor C3 as close as possible to the VCC and ground pins, and assure that there are no other paths for switching noise to enter the IC. Keep the length of the line between the Out pin and the switching device (either a MOSFET or other transistor) as short as possible to provide a clean switching waveform to the switching device. Use a relatively long line for the low-impedance side of the output voltage detection resistor R2.
(2) VIN SBD VOUT
Q1 7 GND 9 OSC 10 FB 6 Out 8 RB (4) GND (1)
AN8016NSH
IN- 1
SS 3
Off 4
S.C.P. 2
24 k R2
C3
VCC 5
(3)
(5)
[3] Evaluation board
SBD
Off
VIN
VOUT +
L1
Q1 BCE
C6
C3
+
GND R6
R4 C2 C1 R1 R2 R3
C4 C5 R5
AN8016NSH DC-DC CONVERTER BOARD
17

▲Up To Search▲

Price & Availability of AN8016

	To Download AN8016 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .