 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| a FEATURES Pin-Programmable 2.5 V or 3.0 V Output Ultralow Drift: 3 ppm/ C Max High Accuracy: 2.5 V or 3.0 V 1 mV Max Low Noise: 100 nV/Hz Noise Reduction Capability Low Quiescent Current: 1 mA Max Output Trim Capability Plug-In Upgrade for Present References Temperature Output Pin Series or Shunt Mode Operation ( 2.5 V, 3.0 V) 2.5 V/3.0 V High Precision Reference AD780 FUNCTIONAL BLOCK DIAGRAM +VIN NC AD780 R10 NC VOUT R13 Q6 R5 TEMP R4 R14 R15 Q7 R16 TRIM R11 PRODUCT DESCRIPTION GND NC = NO CONNECT The AD780 is an ultrahigh precision band gap reference voltage that provides a 2.5 V or 3.0 V output from inputs between 4.0 V and 36 V. Low initial error and temperature drift combined with low output noise and the ability to drive any value of capacitance make the AD780 the ideal choice for enhancing the performance of high resolution ADCs and DACs and for any general-purpose precision reference application. A unique low headroom design facilitates a 3.0 V output from a 5.0 V 10% input, providing a 20% boost to the dynamic range of an ADC, over performance with existing 2.5 V references. The AD780 can be used to source or sink up to 10 mA and can be used in series or shunt mode, thus allowing positive or negative output voltages without external components. This makes it suitable for virtually any high-performance reference application. Unlike some competing references, the AD780 has no "region of possible instability." The part is stable under all load conditions when a 1 F bypass capacitor is used on the supply. A temperature output pin is provided on the AD780. This provides an output voltage that varies linearly with temperature, allowing the AD780 to be configured as a temperature transducer while providing a stable 2.5 V or 3.0 V output. The AD780 is a pin-compatible performance upgrade for the LT1019(A)-2.5 and the AD680. The latter is targeted toward low power applications. The AD780 is available in three grades in plastic DIP and SOIC packages. The AD780AN, AD780AR, AD780BN, AD780BR, and AD780CR are specified for operation from -40C to +85C. O/P SELECT 2.5V - NC 3.0V - GND PRODUCT HIGHLIGHTS 1. The AD780 provides a pin-programmable 2.5 V or 3.0 V output from a 4 V to 36 V input. 2. Laser trimming of both initial accuracy and temperature coefficients results in low errors over temperature without the use of external components. The AD780BN has a maximum variation of 0.9 mV from -40 C to +85 C. 3. For applications requiring even higher accuracy, an optional fine-trim connection is provided. 4. The AD780 noise is extremely low, typically 4 mV p-p from 0.1 Hz to 10 Hz and a wideband spectral noise density of typically 100 nV/ Hz. This can be further reduced if desired, by simply using two external capacitors. 5. The temperature output pin enables the AD780 to be configured as a temperature transducer while providing a stable output reference. REV. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2002 AD780-SPECIFICATIONS Parameter OUTPUT VOLTAGE 2.5 V Out 3.0 V Out OUTPUT VOLTAGE DRIFT1 -40C to +85C -55C to +125C LINE REGULATION 2.5 V Output, 4 V +VIN 36 V TMIN to TMAX 3.0 V Output, 4.5 V +VIN 36 V TMIN to TMAX LOAD REGULATION, SERIES MODE Sourcing 0 < IOUT < 10 mA TMIN to TMAX Sinking -10 < IOUT < 0 mA -40C to +85C -55C to +125C LOAD REGULATION, SHUNT MODE I < ISHUNT < 10 mA QUIESCENT CURRENT, 2.5 V SERIES MODE -40C to +85C -55C to +125C MINIMUM SHUNT CURRENT OUTPUT NOISE 0.1 Hz to 10 Hz Spectral Density, 100 Hz LONG TERM STABILITY3 TRIM RANGE TEMPERATURE PIN Voltage Output @ 25C Temperature Sensitivity Output Resistance SHORT-CIRCUIT CURRENT TO GROUND TEMPERATURE RANGE Specified Performance (A, B, C) Operating Performance (A, B, C)4 Specified Performance (S) Operating Performance (S) 2 (TA = 25 C, VIN = 5 V, unless otherwise noted.) AD780AN/AR AD780CR Min 2.4985 2.9950 Typ Max 2.5015 3.0050 7 20 AD780BN/BR Min 2.499 2.999 Typ Max 2.501 3.001 3 Unit Volts Volts ppm/C ppm/C Min 2.495 2.995 Typ Max 2.505 3.005 7 20 10 10 50 75 75 75 150 75 0.75 0.8 0.7 4 100 20 4.0 500 560 1.9 3 30 -40 -55 -55 -55 +85 +125 +125 +125 -40 -55 -55 -55 620 4.0 500 560 1.9 3 30 1.0 1.3 1.0 0.75 0.8 0.7 4 100 20 10 10 50 75 75 75 150 75 1.0 1.3 1.0 0.75 0.8 0.7 4 100 20 4.0 620 500 560 1.9 3 30 +85 +125 +125 +125 -40 -55 -55 -55 10 10 50 75 75 75 150 75 1.0 1.3 1.0 V/V V/V V/mA V/mA V/mA V/mA V/mA V/mA mA mA mA V p-p nV/Hz ppm/ 1000 Hr % 620 mV mV/C k mA +85 +125 +125 +125 C C C C NOTES 1 Maximum output voltage drift is guaranteed for all packages. 2 3.0 V mode typically adds 100 A to the quiescent current. Also, Iq increases by 2 A/V above an input voltage of 5 V. 3 The long term stability specification is noncumulative. The drift in subsequent 1000 hr. periods is significantly lower than in the first 1000 hr. period. 4 The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance outside their specified temperature range. Specifications subject to change without notice. -2- REV. C AD780 ABSOLUTE MAXIMUM RATINGS* DIE LAYOUT GND TEMP +VIN +VIN to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Trim Pin to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Temp Pin to Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 V Power Dissipation (25C) . . . . . . . . . . . . . . . . . . . . . 500 mW Storage Temperature . . . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature (Soldering 10 sec) . . . . . . . . . . . . . . 300C Output Protection: Output safe for indefinite short to ground and momentary short to VIN. ESD Classification . . . . . . . . . . . . . . . . . . . . . Class 1 (1000 V) *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any conditions above those indicated in the operational specification is not implied. Exposure to absolute maximum specifications for extended periods may affect device reliability. GND PIN CONFIGURATION 8-Lead Plastic DIP and SOIC Packages 2.5V/3.0V O/P SELECT (NC OR GND) NC VOUT TRIM TRIM VOUT 2.5V/3.0V O/P SELECT NC +VIN TEMP GND 1 2 3 4 8 AD780 TOP VIEW (NOT TO SCALE) 7 6 5 NC = NO CONNECT NOTES Both VOUT pads should be connected to the output. Die Thickness: The standard thickness of Analog Devices bipolar dice is 24 mil 2 mil. Die Dimensions: The dimensions given have a tolerance of 2 mil. Backing: The standard backside surface is silicon (not plated). Analog Devices does not recommend gold-backed dice for most applications. Edges: A diamond saw is used to separate wafers into dice thus providing perpendicular edges halfway through the die. In contrast to scribed dice, this technique provides a more uniform die shape and size. The perpendicular edges facilitate handling (such as tweezer pickup), while the uniform shape and size simplify substrate design and die attach. Top Surface: The standard top surface of the die is covered by a layer of glassivation. All areas are covered except bonding pads and scribe lines. Surface Metalization: The metalization to Analog Devices bipolar dice is aluminum. Minimum thickness is 10,000 A. Bonding Pads: All bonding pads have a minimum size of 4.0 mil by 6.0 mil. The passivation windows have a 3.6 mil by 5.6 mil minimum size. ORDERING GUIDE Initial Error 5.0 mV 5.0 mV 5.0 mV 1.0 mV 1.0 mV 1.0 mV 1.0 mV 1.5 mV 1.5 mV Model AD780AN AD780AR AD780AR-REEL7 AD780BN AD780BR AD780BR-REEL AD780BR-REEL7 AD780CR AD780CR-REEL7 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C Temperature Coefficient 7 ppm/C 7 ppm/C 7 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 3 ppm/C 7 ppm/C 7 ppm/C Package Options Plastic DIP SOIC SOIC Plastic DIP SOIC SOIC SOIC SOIC SOIC CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD780 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. WARNING! ESD SENSITIVE DEVICE REV. C -3- AD780 THEORY OF OPERATION Band gap references are the high performance solution for low supply voltage and low power voltage reference applications. In this technique, a voltage with a positive temperature coefficient is combined with the negative coefficient of a transistor's Vbe to produce a constant band gap voltage. In the AD780, the band gap cell contains two npn transistors (Q6 and Q7) that differ in emitter area by 12 . The difference in their Vbes produces a PTAT current in R5. This, in turn, produces a PTAT voltage across R4 that, when combined with the Vbe of Q7, produces a voltage Vbg that does not vary with temperature. Precision laser trimming of the resistors and other patented circuit techniques are used to further enhance the drift performance. +VIN NC The AD780's NC (Pin 7) is a 20 k resistor to V+ that is used solely for production test purposes. Users who are currently using the LT1019 self-heater pin (Pin 7) must take into account the different load on the heater supply. APPLYING THE AD780 The AD780 can be used without any external components to achieve specified performance. If power is supplied to Pin 2 and Pin 4 is grounded, Pin 6 provides a 2.5 V or 3.0 V output depending on whether Pin 8 is left unconnected or grounded. A bypass capacitor of 1 F (+VIN to GND) should be used if the load capacitance in the application is expected to be greater than 1 nF. The AD780 in 2.5 V mode typically draws 700 A of Iq at 5 V. This increases by ~2 A/V up to 36 V. AD780 R10 NC VOUT R13 Q6 R5 TEMP R4 R14 R15 Q7 R16 TRIM R11 +VIN NC 1F NC VOUT AD780 RNULL TRIM TEMP O/P SELECT 2.5V - NC 3.0V - GND R POT GND NC = NO CONNECT GND NC = NO CONNECT O/P SELECT 2.5V - NC 3.0V - GND Figure 2. Optional Fine Trim Circuit Figure 1. Schematic Diagram The output voltage of the AD780 is determined by the configuration of resistors R13, R14, and R15 in the amplifier's feedback loop. This sets the output to either 2.5 V or 3.0 V depending on whether R15 (Pin 8) is grounded or not connected. A unique feature of the AD780 is the low headroom design of the high gain amplifier which produces a precision 3 V output from an input voltage as low as 4.5 V (or 2.5 V from a 4.0 V input). The amplifier design also allows the part to work with +VIN = VOUT when current is forced into the output terminal. This allows the AD780 to work as a two terminal shunt regulator providing a -2.5 V or -3.0 V reference voltage output without external components. The PTAT voltage is also used to provide the user with a thermometer output voltage (at Pin 3) that increases at a rate of approximately 2 mV/C. Initial error can be nulled using a single 25 k potentiometer connected between VOUT, TRIM, and GND. This is a coarse trim with an adjustment range of 4% and is only included here for compatibility purposes with other references. A fine trim can be implemented by inserting a large value resistor (e.g., 1-5 M) in series with the wiper of the potentiometer (see Figure 2 above). The trim range, expressed as a fraction of the output, is simply greater than or equal to 2.1 k/RNULL for either the 2.5 V or 3.0 V mode. The external null resistor affects the overall temperature coefficient by a factor equal to the percentage of VOUT nulled. For example, a 1 mV (0.03%) shift in the output caused by the trim circuit, with a 100 ppm/C null resistor, will add less than 0.06 ppm/C to the output drift (0.03% 200 ppm/C, since the resistors internal to the AD780 also have temperature coefficients of less than 100 ppm/C). NOISE PERFORMANCE The impressive noise performance of the AD780 can be further improved if desired by the addition of two capacitors: a load capacitor, C1, between the output and ground, and a compensation capacitor, C2, between the TEMP pin and ground. Suitable values are shown in Figure 3. -4- REV. C AD780 100 NO AMPLIFIER 20 V 100 90 COMPENSATION CAPACITOR, C2 - nF 10ms 10 10 1 0% 10Hz TO 10kHz 0.1 0.1 1 10 100 LOAD CAPACITOR, C1 - F Figure 6. Reduced Noise Performance with C1 = 100 F, C2 = 100 nF TEMPERATURE PERFORMANCE Figure 3. Compensation and Load Capacitor Combinations C1 and C2 also improve the settling performance of the AD780 when subjected to load transients. The improvement in noise performance is shown in Figures 4, 5, and 6. AMPLIFIER GAIN = 100 100 V 100 90 NO AMPLIFIER 1s 100 90 20 V 10ms The AD780 provides superior performance over temperature by means of a combination of patented circuit design techniques, precision thin film resistors, and drift trimming. Temperature performance is specified in terms of ppm/C, but because of nonlinearity in the temperature characteristic, the Box Test Method is used to test and specify the part. The nonlinearity takes the form of the characteristic S-shaped curve shown in Figure 7. The Box Test Method forms a rectangular box around this curve, enclosing the maximum and minimum output voltages over the specified temperature range. The specified drift is equal to the slope of the diagonal of this box. 2.0 10 0% 10 0% 1.6 0.1 TO 10Hz 10Hz TO 10kHz 1.2 ERROR - mV Figure 4. Standalone Noise Performance 0.8 0.4 +VIN NC 1F NC VOUT 0 -0.4 AD780 TRIM TEMP C2 O/P SELECT 2.5V - NC 3.0V - GND C1 -0.8 -60 -40 -20 0 20 40 60 80 100 120 140 GND TEMPERATURE - C Figure 7. Typical AD780BN Temperature Drift NC = NO CONNECT TEMPERATURE OUTPUT PIN Figure 5. Noise Reduction Circuit NOISE COMPARISON The wideband noise performance of the AD780 can also be expressed in ppm. The typical performance with C1 and C2 is 0.6 ppm and without external capacitors is 1.2 ppm. This performance is respectively 7 and 3 specified performance of the LT1019. lower than the The AD780 provides a TEMP output (Pin 3) that varies linearly with temperature. This output can be used to monitor changes in system ambient temperature and to initiate calibration of the system if desired. The voltage VTEMP is 560 mV at 25C, and the temperature coefficient is approximately 2 mV/C. REV. C -5- AD780 Figure 8 shows the typical VTEMP characteristic curve over temperature taken at the output of the op amp with a noninverting gain of five. 4.25 4.00 3.75 VOLTAGE - VOUT To minimize resistance changes with temperature, resistors with low temperature coefficients, such as metal film resistors, should be used. 5V CIRCUIT CALIBRATED AT 25 C REFER TO FIGURE 9 3.50 3.25 10mV PER C 3.00 2.75 2.50 2.25 2.00 -75 1F +VIN TEMP + AD820 10mV/ C - RF AD780 GND 6.04k RB 1.27k (1%) (1%) -50 -25 0 25 50 75 100 125 150 RBP 200 TEMPERATURE - C Figure 8. Temperature Pin Transfer Characteristic Since the TEMP voltage is acquired from the band gap core circuit, current pulled from this pin will have a significant effect on VOUT. Care must be taken to buffer the TEMP output with a suitable op amp, e.g., an OP07, AD820, or AD711 (all of which would result in less than a 100 V change in VOUT). The relationship between ITEMP and VOUT is as follows: Figure 9. Differential Temperature Transducer SUPPLY CURRENT OVER TEMPERATURE VOUT = 5.8 mV/A x ITEMP (2.5 V range) or VOUT = 6.9 mV/A x ITEMP (3.0 V range) Notice how sensitive the current dependent factor on VOUT is. A large amount of current, even in tens of microamp, drawn from the TEMP pin can cause VOUT and TEMP output to fail. The choice of C1 and C2 was dictated primarily by the need for a relatively flat response that rolled off early in the high-frequency noise at the output. But there is considerable margin in the choice of these capacitors. For example, the user can actually put a huge C2 on the TEMP pin with none on the output pin. However, one must either put very little or a lot of capacitance at the TEMP pin. Intermediate values of capacitance can sometimes cause oscillation. In any case, the user should follow the recommendation in Figure 3. TEMPERATURE TRANSDUCER CIRCUIT The AD780's quiescent current will vary slightly over temperature and input supply range. The test limit is 1 mA over the industrial and 1.3 mA over the military temperature range. Typical performance with input voltage and temperature variation is shown in Figure 10. 0.85 -55 C QUIESCENT CURRENT - mA 0.80 +25 C 0.75 +125 C 0.70 0.65 The circuit shown in Figure 9 is a temperature transducer that amplifies the TEMP output voltage by a gain of a little over +5 to provide a wider full-scale output range. The trimpot can be used to adjust the output so it varies exactly by 10 mV/C. 0.60 4 INPUT VOLTAGE - V 36 Figure 10. Typical Supply Current over Temperature -6- REV. C AD780 TURN-ON TIME OUTPUT CHANGE - 50mV/DIV The time required for the output voltage to reach its final value within a specified error band is defined as the turn-on settling time. The two major factors that affect this are the active circuit settling time and the time for the thermal gradients on the chip to stabilize. Typical settling performance is shown in Figure 11. The AD780 settles to within 0.1% of its final value within 10 s. 0mA 10mA ILOAD VOUT (CL = 0pF) VIN 5V 0V 10 s/DIV VOUT 2.500V 2.499V 2.498V Figure 12b. Settling Under Transient Resistive Load The dynamic load may be resistive and capacitive. For example, the load may be connected via a long capacitive cable. Figures 13a and 13b show the performance of the AD780 driving a 1000 pF, 0 mA to 10 mA load. 10 s/DIV +VIN Figure 11. Turn-On Settling Time Performance DYNAMIC PERFORMANCE The output stage of the AD780 has been designed to provide superior static and dynamic load regulation. Figures 12a and 12b show the performance of the AD780 while driving a 0 mA to 10 mA load. +VIN 1F AD780 VOUT CL 1000pF 249 VL VOUT 0V 1F AD780 249 VOUT Figure 13a. Capacitive Load Transient Response Test Circuit 0mA 10mA ILOAD 0V OUTPUT CHANGE - 50mV/DIV VL VOUT VOUT (CL = 1000pF) Figure 12a. Transient Resistive Load Test Circuit 10 s/DIV Figure 13b. Settling Under Dynamic Capacitive Load REV. C -7- AD780 LINE REGULATION Line regulation is a measure of the change in output voltage due to a specified change in input voltage. It is intended to simulate worst-case unregulated supply conditions and is measured in V/V. Figure 14 shows typical performance with 4.0 V < VIN < 15.0 V. 200 T = 25 C The AD780 is also ideal for use with higher resolution converters, such as the AD7710/AD7711/AD7712 (see Figure 16). While these parts are specified with a 2.5 V internal reference, the AD780 in 3 V mode can be used to improve the absolute accuracy, temperature stability, and dynamic range. It is shown below with the two optional noise reduction capacitors. 5V V 100 +VIN VOUT REFIN+ OUTPUT CHANGE - 0 1F AD780 100 F AD7710 -100 100nF 2.5V/3.0V GND O/P SELECT -200 4 10 INPUT VOLTAGE - V 15 REFIN- Figure 14. Output Voltage Change vs. Input Voltage PRECISION REFERENCE FOR HIGH RESOLUTION 5 V DATA CONVERTERS Figure 16. Precision 2.5 V or 3.0 V Reference for the AD7710 High Resolution, Sigma-Delta ADC 4.5 V REFERENCE FROM 5 V SUPPLY The AD780 is ideally suited to be the reference for most 5 V high resolution ADCs. The AD780 is stable under any capacitive load, it has superior dynamic load performance, and the 3.0 V output provides the converter with the maximum dynamic range without requiring an additional and expensive buffer amplifier. One of the many ADCs that the AD780 is suited for is the AD7884, a 16-bit, high-speed sampling ADC (see Figure 15). This part previously needed a precision 5 V reference, resistor divider, and buffer amplifier to do this function. 5V Some 5 V high resolution ADCs can accommodate reference voltages up to 4.5 V. The AD780 can be used to provide a precision 4.5 V reference voltage from a 5 V supply using the circuit shown in Figure 17. This circuit will provide a regulated 4.5 V output from a supply voltage as low as 4.7 V. The high quality tantalum 10 F capacitor in parallel with the ceramic AD780 0.1 F capacitor and the 3.9 resistor ensures a low output impedance around 50 MHz. VSUPPLY AD7884 +VIN VOUT VREF +F 0.1 F 1k 2N2907 + 1F AD780 VREF +S GND 2.5/3.0V SELECT AD780 OP90 - 2.5k 10 F 0.1 F 3.9 VOUT 0.1 F 5k 0.01% 4k 0.01% Figure 15. Precision 3 V Reference for the AD7884 16-Bit, High-Speed ADC Figure 17. 4.5 V Reference from a Single 5 V Supply -8- REV. C AD780 NEGATIVE (-2.5 V) REFERENCE The AD780 can produce a negative output voltage in shunt mode, simply by connecting the input and output to ground connecting the AD780's GND pin to a negative supply via a bias resistor as shown in Figure 18. A precise -2.5 V reference capable of supplying up to 100 mA to a load can be implemented with the AD780 in series mode using the bootstrap circuit shown below. +5V +VIN +VIN NC NC VOUT 1k +5V OUT AD780 CONNECT IF -3V OUTPUT DESIRED AD780 TEMP 1F GND TRIM O/P SELECT 2.5V - NC 3.0V - GND -2.5 VOUT R= VOUT - (V-) IL + IS MIN V- NOTE 1. IL = LOAD CURRENT 2. IS MIN = MINIMUM SHUNT CURRENT 3. NC = NO CONNECT - -2.5V (IL 100mA) OP07 + 2N3906 -5V -5V 1000pF Figure 18. Negative (-2.5 V) Shunt Mode Reference Figure 19. -2.5 V High Load Current Reference REV. C -9- AD780 OUTLINE DIMENSIONS Dimensions shown in millimeters and (inches) 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) 5.00 (0.1968) 4.80 (0.1890) 8 5 4 4.00 (0.1574) 3.80 (0.1497) PIN 1 1 6.20 (0.2440) 5.80 (0.2284) 1.27 (0.0500) BSC COPLANARITY 0.25 (0.0098) 0.10 (0.0040) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) SEATING 0.33 (0.0130) PLANE 8 0.25 (0.0098) 0 0.19 (0.0075) 0.50 (0.0196) 0.25 (0.0099) 45 1.27 (0.0500) 0.40 (0.0157) CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MS-012 AA Dimensions shown in inches and (mm) 8-Lead Plastic Dual-in-Line Package [PDIP] (N-8) 0.430 (10.92) 0.348 (8.84) 8 5 0.280 (7.11) 0.240 (6.10) 1 4 PIN 1 0.100 (2.54) BSC 0.210 (5.33) MAX 0.160 (4.06) 0.115 (2.93) 0.060 (1.52) 0.015 (0.38) 0.130 (3.30) MIN 0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) 0.022 (0.56) 0.070 (1.77) SEATING 0.014 (0.36) 0.045 (1.15) PLANE 0.015 (0.38) 0.008 (0.20) -10- REV. C AD780 Revision History Location 5/02--Data Sheet changed from REV. B to REV. C. Page Updates to packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 REV. C -11- -12- C00841-0-5/02(C) PRINTED IN U.S.A. |
Price & Availability of AD780AN
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |