View HN27C101APAFPATTSERIES_210682.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HN27C101AP/AFP/ATT Series HN27C301AP/AFP Series
131072-word x 8-bit CMOS One Time Electrically Programmable ROM
Description
The HN27C101AP/AFP/ATT series are 131072-word x 8-bit one time electrically programmable ROM. Initially, all bits of the HN27C101AP/AFP/ATT, HN27C301AP /AFP series are in the "1" state (output high). Data is introduced by selectively programming "0" into the desired bit location. This device is packaged in 32-pin plastic package, therefore, this device cannot be rewritten and erased. The packages of the HN27C101ATT series are surface mount thin and small outline packages. They are suitable for hand-held equipment such as a memory card.
Features
* Single power supply: +5 V 10% * Fast high-reliability programming mode and fast high-reliability page programming mode Programming voltage: +12.5 V DC Fast high-reliability page programming: 14 sec typ * High speed inputs and outputs TTL compatible during both read and program modes * Low power dissipation: 50 mW/MHz typ (active) 5 W typ (standby) * Pin arrangement: 32-pin JEDEC standard except HN27C301A series replaceable 32 pin Mask ROM (HN27C301AP/AFP Series) * Package Surface mount thin and small outline package (TSOP) type II: HN27C101ATT series * Device identifier mode: manufacturer code and device code * Fully compatible with HN27C101P/FP, 301P/FP series
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Ordering Information
Type No. HN27C101AP-12 HN27C101AP-15 HN27C101AP-20 HN27C101AP-25 HN27C301AP-12 HN27C301AP-15 HN27C301AP-20 HN27C301AP-25 HN27C101AFP-12 HN27C101AFP-15 HN27C101AFP-20 HN27C101AFP-25 HN27C301AFP-12 HN27C301AFP-15 HN27C301AFP-20 HN27C301AFP-25 HN27C101ATT-12 HN27C101ATT-15 Access Time 120 ns 150 ns 200 ns 250 ns 120 ns 150 ns 200 ns 250 ns 120 ns 150 ns 200 ns 250 ns 120 ns 150 ns 200 ns 250 ns 120 ns 150ns 32-pin plastic TSOP-(II) (TTP-32D) 32-pin plastic SOP (FP-32D) Package 600-mil 32-pin plastic DIP (DP-32)
2
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Pin Arrangement
HN27C101AP/AFP Series V PP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (Top view) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V CC PGM NC A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3 V PP OE A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS HN27C301AP/AFP Series 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (Top view) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V CC PGM NC A14 A13 A8 A9 A11 A16 A10 CE I/O7 I/O6 I/O5 I/O4 I/O3
HN27C101ATT Series V PP A16 A15 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O0 I/O1 I/O2 VSS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 (Top view) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 V CC PGM NC A14 A13 A8 A9 A11 OE A10 CE I/O7 I/O6 I/O5 I/O4 I/O3
3
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Pin Description
Pin Name A0 - A16 I/O0 - I/O7 CE OE VCC VPP VSS PGM NC Function Address Input/output Chip enable Output enable Power supply Programming power supply Ground Programming enable No connection
4
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Block Diagram
A5 A9 A12 A16 X-Decoder 1024 x 1024 Memory Matrix
I/O0 I/O7
Input Data Control
Y-Gating Y-Decoder
CE OE PGM VCC VPP VSS H H : High Threshold Inverter A0 - A4 A10, A11
5
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Mode Selection
Mode HN27C101A HN27C301A Read Output disable Standby Program Program verify Page data latch Page program Program inhibit CE (22) (22) VIL VIL VIH VIL VIL VIH VIH VIL VIL VIH VIH Identifier VIL Notes: 1. X: Don't care 2. VH : 12.0 V 0.5 V OE (24) (2) VIL VIH X VIH VIL VIL VIH VIL VIH VIL VIH VIL PGM (31) (31) VIH VIH X VIL VIH VIH VIL VIL VIH VIL VIH VIH VH VCC VCC Code A9 (26) (26) X X X X X X X X VPP (1) (1) VCC VCC VCC VPP VPP VPP VPP VPP VCC (32) (32) VCC VCC VCC VCC VCC VCC VCC VCC I/O (13 - 15, 17 - 21) (13 - 15, 17 - 21) Dout High-Z High-Z Din Dout Din High-Z High-Z
Absolute Maximum Ratings
Parameter A11 input and output voltages* A9 input voltage* VPP voltage*
1 1 1 1
Symbol Vin, Vout VID VPP VCC Topr Tstg Tbias
Value -0.6* to +7.0 -0.6* to +13.5 -0.6 to +13.5 -0.6 to +7.0 0 to +70 -55 to +125 -10 to +80
2 2
Unit V V V V C C C
VCC voltage*
Operating temperature range Storage temperature range Storage temperature range under bias
Notes: 1. Relative to VSS 2. Vin, Vout and VID min = -1.0 V for pulse width 50 ns
6
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Capacitance (Ta = 25C, f = 1 MHz)
Parameter Input capacitance Output capacitance Symbol Cin Cout Min -- -- Typ -- -- Max 10 15 Unit pF pF Test Conditions Vin = 0 V Vout = 0 V
Read Operation
DC Characteristics (VCC = 5 V 10%, VPP = VCC, Ta = 0 to +70C)
Parameter Input leakage current Output leakage current VPP current Standby V CC current Symbol I LI I LO I PP1 I SB1 I SB2 Operating VCC current I CC1 I CC2 Min -- -- -- -- -- -- -- -- Input low voltage Input high voltage Output low voltage Output high voltage VIL VIH VOL VOH -0.3* 2.2 -- 2.4 VCC - 0.7
1
Typ -- -- 1 -- 1 -- -- -- -- -- -- -- --
Max 2 2 20 1 20 30 30 45 0.8 VCC + 1.0*2 0.45 -- --
Unit A A A mA mA mA mA mA V V V V V
Test Conditions Vin = 0 V to VCC Vout = 0 V to VCC VPP = 5.5 V CE = VIH CE = VCC 0.3 V CE = VIL, Iout = 0 mA f = 5 MHz, Iout = 0 mA f = 8.4 MHz, Iout = 0 mA
I OL = 2.1 mA I OH = -1 mA I OH = -0.1 mA
Notes: 1. VIL min = -1.0 V for pulse width 50 ns. 2. VIH max = VCC +1.5 V for pulse width 20 ns. If V IH is over the specified maximum value, read operation cannot be guaranteed.
7
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
AC Characteristics (VCC = 5 V 10%, VPP = VCC, Ta = 0 to +70C) Test Conditions * * * * Input pulse levels: 0.45 V to 2.4 V Input rise and fall time: 20 ns Output load: 1 TTL Gate +100 pF Reference levels for measuring timing: Inputs; 0.8 V and 2.0 V Outputs; 0.8 V and 2.0 V
HN27C101AP/AFP/ATT HN27C101AP/AFP HN27C301AP/AFP HN27C301AP/AFP -12 Parameter Symbol Min -- -- -- 0 0 -15 Max Min 120 120 60 50 -- -- -- -- 0 0 -20 -25
Max Min Max Min Max Unit Test Conditions 150 150 70 50 -- -- -- -- 0 0 200 -- 200 -- 70 50 -- -- 0 0 250 ns 250 ns 100 ns 60 -- ns ns CE = OE = VIL OE = VIL CE = VIL CE = VIL CE = OE = VIL
Address to output delay t ACC CE to output delay OE to output delay OE high to output float Address to output hold t CE t OE t DF t OH
Note: t DF is defined as the time at which the output achieves the open circuit condition and data is no longer driven.
Read Timing Waveform
Address
CE
Standby Mode tCE
Active Mode
Standby Mode
OE tOE tACC Data Out Data Out Valid tOH tDF
8
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Fast High-Reliability Programming
This device can be applied the programming algorithm shown in following flowchart. This algorithm allows to obtain faster programming time without any voltage stress to the device nor deterioration in reliability of programmed data.
START SET PROG./VERIFY MODE VPP = 12.5 0.3 V, VCC = 6.0 0.25 V Address = 0 n=0 n+1 n
Program tPW = 0.2 ms 5% Address + 1 Address VERIFY NOGO NO
GO Program tOPW = 0.2n ms NO LAST Address?
n = 25 YES
YES SET READ MODE VCC = 5.0 V 0.25 V, VPP = VCC READ All Address GO END FAIL NOGO
Fast High-Reliability Programming Flowchart
9
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
DC Characteristics (Ta = 25C 5C, VCC = 6 V 0.25 V, VPP = 12.5 V 0.3 V)
Parameter Input leakage current VPP supply current Operating VCC current Input low level Input high level Output low voltage during verify Output high voltage during verify Symbol I LI I PP I CC VIL VIH VOL VOH Min -- -- -- -0.1* 2.2 -- 2.4
5
Typ -- -- -- -- -- -- --
Max 2 40 30 0.8
6
Unit A mA mA V
Test Conditions Vin = 0 V to VCC CE = PGM = VIL
VCC + 0.5* V 0.45 -- V V I OL = 2.1 mA I OH = -400 A
Notes: 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after V PP . 2. VPP must not exceed 13.5 V including overshoot. 3. An influence may be had upon device reliability if the device is installed or removed while VPP = 12.5 V. 4. Do not alter VPP either V IL to 12.5 V or 12.5 V to VIL when CE = Low. 5. VIL min = -0.6 V for pulse width 20 ns. 6. If V IH is over the specified maximum value, programming operation cannot be guaranteed.
10
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
AC Characteristics (Ta = 25C 5C, VCC = 6 V 0.25 V, VPP = 12.5 V 0.3 V) Test Conditions * Input pulse levels: 0.45 V to 2.4 V * Input rise and fall time: 20 ns * Reference levels for measuring timing: Inputs; 0.8 V and 2.0 V Outputs; 0.8 V and 2.0 V
Parameter Address setup time OE setup time Data setup time Address hold time Data hold time OE to output float delay VPP setup time VCC setup time PGM initial programming pulse width PGM overprogramming pulse width CE setup time Data valid from OE Symbol Min t AS t OES t DS t AH t DH t DF * t VPS t VCS t PW t OPW* t CES t OE
2 1
Typ -- -- -- -- -- -- -- -- 0.2 -- -- --
Max -- -- -- -- -- 130 -- -- 0.21 5.25 -- 150
Unit s s s s s ns s s ms ms s ns
Test Conditions
2 2 2 0 2 0 2 2 0.19 0.19 2 0
Notes: 1. t DF is defined as the time at which the output achieves the open circuit condition and data is no longer driven. 2. Refer to the programming flowchart for tOPW.
11
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Fast High-Reliability Programming Timing Waveform
Program Address tAS tAH Program Verify
Data tDS VPP VCC tVPS VCC+1 VCC tVCS
Data In Stable tDH
Data Out Valid tDF
VPP
VCC
CE
tCES
PGM tPW OE tOES tOE
12
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Fast High-Reliability Page Programming
This device can be applied the high performance page programming algorithm shown in following flowchart. This algorithm allows to obtain faster programming time without any voltage stress to the device nor deterioration in reliability of programmed data.
START SET PAGE PROG. LATCH MODE VPP = 12.5 0.3 V, VCC = 6.0 0.25 V Address = 0 A n=0 Latch Address + 1 Address Address + 1 Address Latch Address + 1 Address B Latch Address + 1 Address Latch A NO B n+1 n NO n = 25 YES
SET PAGE PROG./ VERIFY MODE VPP = 12.5 0.3 V, VCC = 6.0 0.25 V Program tPW = 0.2 ms 5% VERIFY NOGO
GO Program tOPW = 0.2n ms LAST Address?
YES SET READ MODE VCC = 5.0 V 0.25 V, VPP = VCC READ All Address GO END FAIL NOGO
Fast High-Reliability Page Programming Flowchart
13
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
DC Characteristics (Ta = 25C 5C, VCC = 6 V 0.25 V, VPP = 12.5 V 0.3 V)
Parameter Input leakage current VPP supply current Operating VCC current Input low level Input high level Output low voltage during verify Symbol Min I LI I PP I CC VIL VIH VOL -- -- -- -0.1* 2.2 -- 2.4
5
Typ -- -- -- -- -- -- --
Max 2 50 30 0.8 VCC + 0.5*6 0.45 --
Unit A mA mA V V V V
Test Conditions Vin = 0 V to VCC CE = OE= VIH, PGM = VIL
I OL = 2.1 mA I OH = -400 A
Output high voltage during verify VOH
Notes: 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after V PP . 2. VPP must not exceed 13.5 V including overshoot. 3. An influence may be had upon device reliability if the device is installed or removed while VPP = 12.5 V. 4. Do not alter VPP either V IL to 12.5 V or 12.5 V to VIL when CE = Low. 5. VIL min = -0.6 V for pulse width 20 ns 6. If V IH is over the specified maximum value, programming operation cannot be guaranteed.
14
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
AC Characteristics (Ta = 25C 5C, VCC = 6 V 0.25 V, VPP = 12.5 V 0.3 V) Test Conditions * Input pulse levels: 0.45 V to 2.4 V * Input rise and fall time: 20 ns * Reference levels for measuring timing: Inputs; 0.8 V and 2.0 V Outputs; 0.8 V and 2.0 V
Parameter Address setup time OE setup time Data setup time Address hold time Symbol t AS t OES t DS t AH t AHL Data hold time OE to output float delay VPP setup time VCC setup time PGM initial programming pulse width PGM overprogramming pulse width CE setup time Data valid from OE OE pulse width during data latch PGM setup time CE hold time OE hold time t DH t DF * t VPS t VCS t PW t OPW* t CES t OE t LW t PGMS t CEH t OEH
2 1
Min 2 2 2 0 2 2 0 2 2 0.19 0.19 2 0 1 2 2 2
Typ -- -- -- -- -- -- -- -- -- 0.2 -- -- -- -- -- -- --
Max -- -- -- -- -- -- 130 -- -- 0.21 5.25 -- 150 -- -- -- --
Unit s s s s s s ns s s ms ms s ns s s s s
Notes: 1. t DF is defined as the time at which the output achieves the open circuit condition and data is no longer driven. 2. Refer to the programming flowchart for tOPW.
15
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Fast High-Reliability Page Programming Timing Waveform
Page data latch A2 to A16 tAS A0, A1 tDS Data Data in stable VPP VCC VPP VCC VCC+1 VCC tVPS tVCS tCES tOEH Data out valid tDH tPGMS tOE tDF tAHL tAH Page program program verify
CE tCEH tPW PGM tOES OE tLW
16
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Mode Description
Device Identifier Mode The device identifier mode allows the reading out of binary codes that identify manufacturer and type of device, from outputs of OTPROM. By this mode, the device will be automatically matched its own corresponding programming algorithm, using programming equipment. HN27C101AP/AFP/ATT Identifier Code
A0 (12) VIL VIH A9 (26) VH VH I/O7 (21) 0 0 I/O6 (20) 0 0 I/O5 (19) 0 1 I/O4 (18) 0 1 I/O3 (17) 0 1 I/O2 (15) 1 0 I/O1 (14) 1 0 I/O0 (13) 1 0
Identifier Manufacturer code Device code
Hex Data 07 38
HN27C301AP/AFP Identifier Code
A0 (12) VIL VIH A9 (26) VH VH I/O7 (21) 0 1 I/O6 (20) 0 0 I/O5 (19) 0 1 I/O4 (18) 0 1 I/O3 (17) 0 1 I/O2 (15) 1 0 I/O1 (14) 1 0 I/O0 (13) 1 1
Identifier Manufacturer code Device code
Hex Data 07 B9
Notes: 1. VH = 12.0 V 0.5 V 2. A1 - A8, A10 - A16, CE, OE = VIL, PGM = VIH
17
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Recommended Screening Conditions Before mounting, please make the screening (baking without bias) shown in the right.
Program and verify by programmer
Baking at 125 to 150C for 24 to 48 hrs
Ensuring read-out
Mounting Recommended Screening Conditions
18
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
Package Dimensions
HN27C101AP/HN27C301AP Series (DP-32)
41.90 42.50 Max Unit: mm
32
17 13.40 13.70 Max
1 2.30 Max
5.08 Max
1.20
16 15.24
0.51 Min 2.54 Min
2.54 0.25
0.48 0.10
0.25 - 0.05 0 - 15
+ 0.11
HN27C101AFP/HN27C301AFP Series (FP-32D)
20.45 20.95 Max 32 17
Unit: mm
1 1.00 Max
16 3.00 Max 14.14 0.30
+ 0.13 - 0.07
11.30
1.42
0.22
1.27
0.10 0.40 + 0.05 -
0.10 0.15 M
+ 0.12 - 0.10
0-8 0.80 0.20
0.15
19
HN27C101AP/AFP/ATT HN27C301AP/AFP Series
HN27C101ATT Series (TTP-32D)
20.95 21.35 Max 32 17 Unit: mm
1 0.40 0.10 1.15 Max
1.27 0.21
M
16
10.16
11.76 0.20 0 - 5 0.80
0.10
0.17 0.05
0.13 0.05
1.20 Max
0.50 0.10
20

▲Up To Search▲

Price & Availability of HN27C101APAFPATTSERIES

	To Download HN27C101APAFPATTSERIES Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .