View M5M29GB_213722.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY DESCRIPTION
The MITSUBISHI Mobile FLASH M5M29GB/T161BWG are 3.3V-only high speed 16,777,216-bit CMOS boot block Flash Memories with alternating BGO (Back Ground Operation) feature. The BGO feature of the device allows Program or Erase operations to be performed in one bank while the device simultaneously allows Read operations to be performed on the other bank. This BGO feature is suitable for mobile and personal computing, and communication products. The M5M29GB/T161BWG are fabricated by CMOS technology for the peripheral circuits and DINOR(Divided bit line NOR) architecture for the memory cells, and are available in 6x8-balls CSP (0.75mm ball pitch) .
FEATURES
Organization
.................................1048,576 word x 16bit
(M5M29GB/T161BWG)
Boot Block M5M29GB161BWG ........................ Bottom Boot M5M29GT161BWG ........................ Top Boot Other Functions Soft Ware Command Control Selective Block Lock Erase Suspend/Resume Program Suspend/Resume Status Register Read Alternating Back Ground Program/Erase Operation Between Bank(I) and Bank(II) Package 7mm x 8.5mm CSP (Chip Scale Package) - 6 x 8 balls, 0.75mm ball pitch
............................. VCC = 2.7~3.6V Supply voltage ................................
Access time
.............................. 90ns (Max.)
Power Dissipation ................................. 54 mW (Max. at 5MHz) Read (After Automatic Power saving) .......... 0.33W (typ.) .......................126 mW (Max.) Program/Erase ................................. 0.33W (typ.) Standby ....................... 0.33W (typ.) Deep power down mode Auto program for Bank(I) ................................. 4ms (typ.) Program Time Program Unit (Byte Program) .........................1word (Page Program) ......................... 128word Auto program for Bank(II) ................................. 4ms (typ.) Program Time ................................. 128word Program Unit Auto Erase ................................. 40 ms (typ.) Erase time Erase Unit Bank(I) Boot Block ..................... 16Kword x 1 .............. 16Kword x 7 Parameter Block ...................... 32Kword x 28 Bank(II) Main Block Program/Erase cycles .........................................100Kcycles
APPLICATION
Digital Cellular Phone Telecommunication Mobile Computing Machine PDA (Personal Digital Assistance) Car Navigation System Video Game Machine
PIN CONFIGURATION (TOP VIEW)
8.5mm
6 5 4 3 2 1
A13 A14 A15
A11 A10
A8 WE# A9
WP2# WP1# RP# NC A18
A19 A17 A6
A7 A5 A3
A4 A2
7.0mm
A12
NC
A1
A16
D14
D5
D11
D2
D8
CE#
A0
NC
D15 D7
D6
D12 D4
D3
D9 D10
D0 D1
GND
GND
D13
VCC
OE#
INDEX
A
B
CD
E
F
G
H
M5M29GB/T161BWG CSP(0.75mm ball pitch):48FJA 16-bit version NC : NO CONNECTION
1 Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
BLOCK DIAGRAM
ADDRESS INPUTS
A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
CE# OE# WE# WP1# WP2# RP#
128 WORD PAGE BUFFER Main Block 32KW
VCC (3.3V)
28
Bank(II)
GND (0V)
Main Block
Parameter Block7 Parameter Block6 Parameter Block5 Parameter Block4 Parameter Block3 Parameter Block2 Parameter Block1 Boot Block
X-DECODER Bank(I)
32KW
16KW 16KW 16KW 16KW 16KW 16KW 16KW 16KW
Y-DECODER
Y-GATE / SENSE AMP.
STATUS / ID REGISTER
CHIP ENABLE INPUT OUTPUT ENABLE INPUT WRITE ENABLE INPUT WRITE PROTECT INPUT WRITE PROTECT INPUT RESET/POWER DOWN INPUT
MULTIPLEXER
CUI
WSM INPUT/OUTPUT BUFFERS
DQ15 DQ14DQ13DQ12
DQ3DQ2DQ1DQ0
DATA INPUTS/OUTPUTS
M5M29GB/T161BWG (16 bit version)
2
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY FUNCTION
The M5M29GB/T161BWG includes on-chip program/erase control circuitry. The Write State Machine (WSM) controls block erase and byte/page program operations. Operational modes are selected by the commands written to the Command User Interface (CUI). The Status Register indicates the status of the WSM and when the WSM successfully completes the desired program or block erase operation. A Deep Powerdown mode is enabled when the RP# pin is at GND, minimizing power consumption. Read The M5M29GB/T161BWG has three read modes, which accesses to the memory array, the Device Identifier and the Status Register. The appropriate read command are required to be written to the CUI. Upon initial device powerup or after exit from deep powerdown, the M5M29GB/T161BWG automatically resets to read array mode. In the read array mode, low level input to CE# and OE#, high level input to WE# and RP#, and address signals to the address inputs (A19-A0:M5M29GB/T161BWG) output the data of the addressed location to the data input/output (D15-D0:M5M29GB/T161BWG). Write Writes to the CUI enables reading of memory array data, device identifiers and reading and clearing of the Status Register. They also enable block erase and program. The CUI is written by bringing WE# to low level, while CE# is at low level and OE# is at high level. Address and data are latched on the earlier rising edge of WE# and CE#. Standard micro-processor write timings are used. Alternating Background Operation (BGO) The M5M29GB/T161BWG allows to read array from one bank while the other bank operates in software command write cycling or the erasing / programming operation in the background. Read array operation with the other bank in BGO is performed by changing the bank address without any additional command. When the bank address points the bank in software command write cycling or the erasing / programming operation, the data is read out from the status register. The access time with BGO is the same as the normal read operation. Output Disable When OE# is at VIH, output from the devices is disabled. Data input/output are in a high-impedance(High-Z) state. Standby When CE# is at VIH, the device is in the standby mode and its power consumption is reduced. Data input/output are in a high-impedance(High-Z) state. If the memory is deselected during block erase or program, the internal control circuits remain active and the device consume normal active power until the operation completes. Deep Power-Down When RP# is at VIL, the device is in the deep powerdown mode and its power consumption is substantially low. During read modes, the memory is deselected and the data input/output are in a high-impedance(High-Z) state. After return from powerdown, the CUI is reset to Read Array , and the Status Register is cleared to value 80H. During block erase or program modes, RP# low will abort either operation. Memory array data of the block being altered become invalid. Automatic Power-Saving (APS) The Automatic Power-Saving minimizes the power consumption during read mode. The device automatically turns to this mode when any addresses or CE# isn't changed more than 200ns after the last alternation. The power consumption becomes the same as the stand-by mode. While in this mode, the output data is latched and can be read out. New data is read out correctly when addresses are changed.
3
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
SOFTWARE COMMAND DEFINITIONS The device operations are selected by writing specific software command into the Command User Interface. Read Array Command (FFH) The device is in Read Array mode on initial device power up and after exit from deep powerdown, or by writing FFH to the Command User Interface. After starting the internal operation the device is set to the read status register mode automatically. Read Device Identifier Command (90H) It can normally read device identifier codes when Read Device Identifier Code Command(90H) is written to the command latch. Following the command write, the manufacturer code and the device code can be read from address 0000H and 0001H, respectively. Read Status Register Command (70H) The Status Register is read after writing the Read Status Register command of 70H to the Command User Interface. Also, after starting the internal operation the device is set to the Read Status Register mode automatically. The contents of Status Register are latched on the later falling edge of OE# or CE#. So CE# or OE# must be toggled every status read. Clear Status Register Command (50H) The Erase Status, Program Status and Block Status bits are set to "1"s by the Write State Machine and can only be reset by the Clear Status Register command of 50H. These bits indicates various failure conditions. C)Single Data Load to Page Buffer (74H) / Page Buffer to Flash (0EH/D0H) Single data load to the page buffer is performed by writing 74H followed by a second write specifying the column address and data. Distinct data up to 128word can be loaded to the page buffer by this two-command sequence. On the other hand, all of the loaded data to the page buffer is programed simultaneously by writing Page Buffer to Flash command of 0EH followed by the confirm command of D0H. After completion of programing the data on the page buffer is cleared automatically. This command is valid for only Bank(I) alike Word Program. Clear Page Buffer Command (55H) Loaded data to the page buffer is cleared by writing the Clear Page Buffer command of 55H followed by the Confirm command of D0H. This command is valid for clearing data loaded by Single Data Load to Page Buffer command. Suspend/Resume Command (B0H/D0H) Writing the Suspend command of B0H during block erase operation interrupts the block erase operation and allows read out from another block of memory. Writing the Suspend command of B0H during program operation interrupts the program operation and allows read out from another block of memory. The Bank address is required when writing the Suspend/Resume Command. The device continues to output Status Register data when read, after the Suspend command is written to it. Polling the WSM Status and Suspend Status bits will determine when the erase operation or program operation has been suspended. At this point, writing of the Read Array command to the CUI enables reading data from blocks other than that which is suspended. When the Resume command of D0H is written to the CUI, the WSM will continue with the erase or program processes.
DATA PROTECTION Block Erase / Confirm Command (20H/D0H) Automated block erase is initiated by writing the Block Erase command of 20H followed by the Confirm command of D0H. An address within the block to be erased is required. The WSM executes iterative erase pulse application and erase verify operation. Program Commands A)Word Program (40H) Word program is executed by a two-command sequence. The Word Program Setup command of 40H is written to the Command Interface, followed by a second write specifying the address and data to be written. The WSM controls the program pulse application and verify operation. The Word Program Command is Valid for only Bank(I). B)Page Program for Data Blocks (41H) Page Program for Bank(I) and Bank(II) allows fast programming of 128words of data. Writing of 41H initiates the page program operation for the Data area. From 2nd cycle to 129th cycle , write data must be serially inputted. Address A6-A0 have to be incremented from 00H to 7FH. After completion of data loading, the WSM controls the program pulse application and verify operation. The M5M29GB/T161BWG provides selectable block locking of memory blocks. Each block has an associated nonvolatile lock-bit which determines the lock status of the block. In addition, the M5M29GB/T161BWG have a master Write Protect pin (WP1# & WP2#) which prevents any modifications to memory blocks whose lock-bits are set to "0", when WP1# or WP2# is low. When WP1# & WP2# are high , all blocks can be programmed or erased regardless of the state of the lock-bits, and the lock-bits are cleared to "1" by erase. See the BLOCK LOCKING table on P.9 for details. Power Supply Voltage When the power supply voltage (Vcc) is less than VLKO, Low VCC Lock-Out voltage, the device is set to the Read-only mode. Regarding DC electrical characteristics of VLKO, see P.9 A delay time of 2 us is required before any device operation is initiated. The delay time is measured from the time Vcc reaches Vccmin (2.7V). During power up, RP#=GND is recommended. Falling in Busy status is not recommended for possibility of damaging the device. MEMORY ORGANIZATION The M5M29GB/T161BWG has one 16Kword boot block, seven 16Kword parameter blocks, for Bank(I) and twenty-eight 32Kword main blocks for Bank(II). A block is erased independently of other blocks in the array.
4
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
Mitsubishi 16M Flash Memory Type name
M 5 M 29G T 160B WG
Operating Voltage : 29G : 2.7 - 3.6V Standard / BGO Type 29W : 1.65 - 2.2V Standard / BGO Type Boot Block : T : Top Boot B : Bottom Boot Density/Write Protect/ Word Organizetion: 160B : 16M WP1#, x8/x16 161B : 16M WP1# & WP2#, x16
Package : VP : 48pin TSOP(I) 12mm x 20mm (Nomal Pinout) WG: CSP Ball Pitch 0.75mm,6x8 array, 7mm x 8.5mm
5
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
MEMORY ORGANIZATION
x16 ( Wordmode) F8000H-FFFFFH F0000H-F7FFFH E8000H-EFFFFH E0000H-E7FFFH D8000H-DFFFFH D0000H-D7FFFH C8000H-CFFFFH C0000H-C7FFFH B8000H-BFFFFH B0000H-B7FFFH A8000H-AFFFFH A0000H-A7FFFH 98000H-9FFFFH 90000H-97FFFH 88000H-8FFFFH 80000H-87FFFH 78000H-7FFFFH 70000H-77FFFH 68000H-6FFFFH 60000H-67FFFH 58000H-5FFFFH 50000H-57FFFH 48000H-4FFFFH 40000H-47FFFH 38000H-3FFFFH 30000H-37FFFH 28000H-2FFFFH 20000H-27FFFH 1C000H-1FFFFH 18000H-1BFFFH 14000H-17FFFH 10000H-13FFFH 0C000H-0FFFFH 08000H-0BFFFH 04000H-07FFFH 00000H-03FFFH A19-A0 (M5M29GB161BWG) x16 ( Wordmode)
32Kword MAIN BLOCK 35 32Kword MAIN BLOCK 34 32Kword MAIN BLOCK 33 32Kword MAIN BLOCK 32 32Kword MAIN BLOCK 31 32Kword MAIN BLOCK 30 32Kword MAIN BLOCK 29 32Kword MAIN BLOCK 28 32Kword MAIN BLOCK 27 32Kword MAIN BLOCK 26 32Kword MAIN BLOCK 25 32Kword MAIN BLOCK 24 32Kword MAIN BLOCK 23 BANK(II) BANK(I) 32Kword MAIN BLOCK 22 32Kword MAIN BLOCK 21 32Kword MAIN BLOCK 20 32Kword MAIN BLOCK 19 32Kword MAIN BLOCK 18 32Kword MAIN BLOCK 17 32Kword MAIN BLOCK 16 32Kword MAIN BLOCK 15 32Kword MAIN BLOCK 14 32Kword MAIN BLOCK 13 32Kword MAIN BLOCK 12 32Kword MAIN BLOCK 11 32Kword MAIN BLOCK 10 32Kword MAIN BLOCK 9 32Kword MAIN BLOCK 8
16Kword PARAMETER BLOCK 7 16Kword PARAMETER BLOCK 6 16Kword PARAMETER BLOCK 5 16Kword PARAMETER BLOCK 4 16Kword PARAMETER BLOCK 3 16Kword PARAMETER BLOCK 2 16Kword PARAMETER BLOCK 1
FC000H-FFFFFH
16Kword BOOT BLOCK 35
F8000H-FBFFFH 16Kword PARAMETER BLOCK 34 F4000H-F7FFFH 16Kword PARAMETER BLOCK 33
BANK(I)
F0000H-F3FFFH 16Kword PARAMETER BLOCK 32 EC000H-EFFFFH 16Kword PARAMETER BLOCK 31 E8000H-EBFFFH 16Kword PARAMETER BLOCK 30 E4000H-E7FFFH 16Kword PARAMETER BLOCK 29 E0000H-E3FFFH 16Kword PARAMETER BLOCK 28 D8000H-DFFFFH D0000H-D7FFFH C8000H-CFFFFH C0000H-C7FFFH B8000H-BFFFFH B0000H-B7FFFH A8000H-AFFFFH A0000H-A7FFFH 98000H-9FFFFH 90000H-97FFFH 88000H-8FFFFH 80000H-87FFFH 78000H-7FFFFH 70000H-77FFFH 68000H-6FFFFH 60000H-67FFFH 58000H-5FFFFH 50000H-57FFFH 48000H-4FFFFH 40000H-47FFFH 38000H-3FFFFH 30000H-37FFFH 28000H-2FFFFH 20000H-27FFFH 18000H-1FFFFH 10000H-17FFFH 08000H-0FFFFH 00000H-07FFFH A19-A0 (M5M29GT161BWG)
32Kword MAIN BLOCK 27 32Kword MAIN BLOCK 26 32Kword MAIN BLOCK 25 32Kword MAIN BLOCK 24 32Kword MAIN BLOCK 23 32Kword MAIN BLOCK 22 32Kword MAIN BLOCK 21 32Kword MAIN BLOCK 20 32Kword MAIN BLOCK 19 32Kword MAIN BLOCK 18 32Kword MAIN BLOCK 17 32Kword MAIN BLOCK 16 BANK(II) 32Kword MAIN BLOCK 15 32Kword MAIN BLOCK 14 32Kword MAIN BLOCK 13 32Kword MAIN BLOCK 12 32Kword MAIN BLOCK 11 32Kword MAIN BLOCK 10 32Kword MAIN BLOCK 9 32Kword MAIN BLOCK 8 32Kword MAIN BLOCK 7 32Kword MAIN BLOCK 6 32Kword MAIN BLOCK 5 32Kword MAIN BLOCK 4 32Kword MAIN BLOCK 3 32Kword MAIN BLOCK 2 32Kword MAIN BLOCK 1 32Kword MAIN BLOCK 0
16Kword BOOT BLOCK 0
M5M29GB161BWG Memory Map
M5M29GT161BWG Memory Map
6
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
BUS OPERATIONS Bus Operations for Word-Wide Mode (M5M29GB/T161BWG)
Mode Read Pins CE# VIL VIL VIL VIL VIL VIH VIL VIL VIL X OE# VIL VIL VIL VIL VIH X 1) VIH VIH VIH X WE# VIH VIH VIH VIH VIH X VIL VIL VIL X RP# VIH VIH VIH VIH VIH VIH VIH VIH VIH VIL DQ0-15 Data out Status Register Data Lock Bit Data (DQ6) Identifier Code Hi-Z Hi-Z Command/Data in Command Command Hi-Z
Array Status Register Lock Bit Status Identifier Code Output disable Stand by Program Write Erase Others Deep Power Down
1) X can be VIH or VIL for control pins.
7
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
SOFTWARE COMMAND DEFINITION Command List
1st bus cycle Command Mode Read Array Device Identifier Read Status Register Clear Status Register Clear Page Buffer Word Program 5) Page Program 7) Single Data Load to Page Buffer 5) Page Buffer to Flash 5) Block Erase / Confirm Suspend Resume Read Lock Bit Status Lock Bit Program / Confirm Erase All Unlocked Blocks Write Write Write Write Write Write Write Write Write Write Write Write Write Write Write Address X X Bank3) X X Bank(I) 5) Bank Bank(I) 5) Bank(I) 5) Bank Bank Bank X Bank X Data
(DQ15-0) 1)
2nd bus cycle Data Mode Address IA 2) Bank X WA 6) WA0 7) WA WA 8) BA 9)
(DQ15-0)
3rd ~129th bus cycles (M5M29GB/T161BWG)
Data Mode Address
(DQ15-0)
FFH 90H 70H 50H 55H 40H 41H 74H 0EH 20H B0H D0H 71H 77H A7H
Read Read Write Write Write Write Write Write
ID 2) SRD4) D0H 1) WD 6) WD0 7) WD D0H 1) D0H 1)
Write
WAn 7)
WDn 7)
Read Write Write
BA BA X
DQ6 10) D0H 1) D0H 1)
1) Upper byte data (DQ8-DQ15) is ignored. 2) IA=ID Code Address : A0=VIL (Manufacturer's Code) : A0=VIH (Device Code), ID=ID Code 3) Bank = Bank Address (Bank(I) or Bank(II)). A19-A17. 4) SRD = Status Register Data 5) Word Program, Single Data Load and Page Buffer to Flash Command is valid for only Bank(I). 6) WA = Write Address,WD = Write Data 7) WA0,WAn=Write Address, WD0,WDn=Write Data. : Write Address and Write Data must be provided sequentially from 00H to 7FH for A6-A0. Page size is 128word (128word x 16bit). and also A19-A7(Block Address, Page Address) must be valid. 8) WA = Write Address : Upper page address, A19-A7(Block Address, Page Address) must be valid. 9) BA = Block Address : Bank1: A19-A14 Bank2: A19-A15 10) DQ6 provides Block Lock Status, DQ6 = 1 : Block Unlock, DQ6 = 0 : Block Locked.
8
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY BLOCK LOCKING
161BWG RP# VIL WP1# X VIL VIH VIH VIL VIH Lock Bit WP2# (Internally) X VIH VIH VIL VIL X 0 1 X X 0 1 Write Protection Provided BANK(I) BANK(II) Lock Bit Boot Parameter Data Locked Locked Locked Locked Locked Locked Locked Locked Locked Locked Unlocked Unlocked Unlocked Unlocked Unlocked Unlocked Locked Locked Locked Locked Locked Locked Locked Locked Locked Locked Locked Unlocked
Note Deep Power Down Mode
All Blocks Unlocked All Blocks Locked
Only Parameter Block is Unlocked
1) DQ6 provides Lock Status of each block after writing the Read Lock Status command (71H). WP1# & WP2# pins must not be switched during performing Erase / Write operations or WSM Busy (WSMS = 0). 2) Erase/Write command for locked blocks is aborted. At this time read mode is not array read mode but status read mode and 00B0H is read. Please issue Clear Status Register command plus Read Array command to change the mode from status read mode to array read mode.
STATUS REGISTER
Symbol SR.7 SR.6 SR.5 SR.4 SR.3 SR.2 SR.1 SR.0 (DQ7) (DQ6) (DQ5) (DQ4) (DQ3) (DQ2) (DQ1) (DQ0) Status Write State Machine Status Suspend Status Erase Status Program Status Block Status after Program Reserved Reserved Reserved Definition "1" Ready Suspended Error Error Error "0" Busy Operation in Progress / Completed Successful Successful Successful -
*DQ3 indicates the block status after the page programming, byte/word programming and page buffer to flash. When DQ3 is "1", the page has the over-programed cell . If over-program occurs, the device is block fail. However if DQ3 is "1", please try the block erase to the block. The block may revive.
9
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY DEVICE IDENTIFIER CODE
Code Manufacturer Code Device Code (-T161BWG) Device Code (-B161BWG)
The upper data(D15-8) is "0".
Pins
A0 VIL VIH VIH
DQ7 0 1 1
DQ6 0 0 0
DQ5 0 1 1
DQ4 1 0 0
DQ3 1 0 0
DQ2 1 0 0
DQ1 0 0 0
DQ0 0 0 1
Hex. Data 1CH A0H A1H
ABSOLUTE MAXIMUM RATINGS
Symbol Vcc VI1 Ta Tbs Tstg I OUT Parameter Vcc voltage All input or output voltage except Vcc,A9,RP# Ambient temperature Temperature under bias Storage temperature Output short circuit current Conditions
1)
Min -0.2 -0.6 -40 -50 -65
Max 4.6 4.6 85 95 125 100
Unit V V C C C mA
With respect to Ground
1) Minimum DC voltage is -0.5V on input/output pins. During transitions, this level may undershoot to -2.0V for periods <20ns. Maximum DC voltage on input/output pins is VCC+0.5V which, during transitions, may overshoot to VCC+1.5V for periods <20ns.
CAPACITANCE
Symbol CIN COUT Parameter Input capacitance (Address, Control Pins) Output capacitance Test conditions Ta = 25C, f = 1MHz, Vin = Vout = 0V Min Limits Typ Max 8 12 Unit pF pF
DC ELECTRICAL CHARACTERISTICS (Ta = -40~ 85C, Vcc = 2.7V ~ 3.6V, unless otherwise noted)
Symbol ILI ILO ISB1 ISB2 ISB3 ISB4 ICC1 ICC2 ICC3 ICC4 ICC5 VIL VIH VOL VOH1 VOH2 VLKO Parameter Input leakage current Output leakage current VCC standby current Test conditions 0VVINVCC 0VVOUTVCC VCC = 3.6V, VIN=VIL/VIH, CE# = RP# =WP# = VIH VCC = 3.6V, VIN=GND or VCC, CE# = RP# = WP# = VCC0.3V VCC = 3.6V, VIN=VIL/VIH, RP# = VIL VCC = 3.6V, VIN=GND or VCC, RP# =GND0.3V VCC = 3.6V, VIN=VIL/VIH, CE# = VIL, 5MHz RP#=OE#=VIH, IOUT = 0mA 1MHz VCC = 3.6V,VIN=VIL/VIH, CE# =WE#= VIL, RP#=OE#=VIH VCC = 3.6V, VIN=VIL/VIH, CE# = RP# =WP# = VIH VCC = 3.6V, VIN=VIL/VIH, CE# = RP# =WP# = VIH VCC = 3.6V, VIN=VIL/VIH, CE# = RP# =WP# = VIH - 0.5 2.0 IOL = 4.0mA IOH = -2.0mA IOH = -100A 0.85Vcc
Vcc-0.4
Min
Limits Typ1)
50 0.1 5 0.1 8 2
Max 1.0 10 200 5 15 5 15 4 15 35 35 200 0.8
Vcc+0.5
Unit A A A A A A mA mA mA mA A V V V V V V
VCC deep powerdown current VCC read current for Word or Byte VCC Write current for Word or Byte VCC program current VCC erase current VCC suspend current Input low voltage Input high voltage Output low voltage Output high voltage Low VCC Lock-Out voltage 2)
0.45
1.5
2.2
All currents are in RMS unless otherwise noted. 1) Typical values at Vcc=3.3V, Ta=25C 2) To protect against initiation of write cycle during Vcc power-up/ down, a write cycle is locked out for Vcc less than VLKO. If Vcc is less than VLKO, Write State Machine is reset to read mode. When the Write State Machine is in Busy state, if Vcc is less than VLKO, the alteration of memory contents
may occur.
10
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
AC ELECTRICAL CHARACTERISTICS (Ta = -40 ~85C, Vcc = 2.7V ~3.6V) Read-Only Mode
Limits
Symbol
Parameter Min 90
Vcc=2.7-3.6V 90ns Typ Max 90 90 30 0 25 0 25 150 0 150
Unit
tRC ta (AD) ta (CE) ta (OE) tCLZ tDF(CE) tOLZ tDF(OE) tPHZ tOH tPS
tAVAV tAVQV tELQV tGLQV tELQX tEHQZ tGLQX tGHQZ tPLQZ tOH tPHEL
Read cycle time Address access time Chip enable access time Output enable access time Chip enable to output in low-Z Chip enable high to output in high Z Output enable to output in low-Z Output enable high to output in high Z RP# low to output high-Z Output hold from CE#, OE#, addresses RP# recovery to CE# low
ns ns ns ns ns ns ns ns ns ns ns
Timing measurements are made under AC waveforms for read operations.
AC ELECTRICAL CHARACTERISTICS (Ta = -40 ~85C, Vcc = 2.7V ~3.6V) Write Mode (WE# control)
Limits Vcc=2.7-3.6V Min 90 50 0 50 0 10 30 0 0 60 30 0 90 0 4 40 150 80 600 90 90ns Typ Max ns ns ns ns ns ns ns ns ns ns ns ns ns ns ms ms ns ns
Symbol
Parameter
Unit
tWC tAS tAH tDS tDH tOEH tRE tCS tCH tWP tWPH tGHWL tBLS tBLH
tAVAV tAVWH tWHAX tDVWH tWHDX tWHGL tELWL tWHEH tWLWH tWHWL tGHWL tPHHWH tQVPH
Write cycle time Address set-up time Address hold time Data set-up time Data hold time OE# hold from WE# high Latency between Read and Write FFH or 71H Chip enable set-up time Chip enable hold time
Write pulse width Write pulse width high OE# hold to WE# Low Block Lock set-up to write enable high Block Lockhold from valid SRD tDAP tWHRH1 Duration of auto-program operation tDAE tWHRH2 Duration of auto-block erase operation tWHRL tWHRL Write enable high to F-RY/BY# low tPS tPHWL RP# high recovery to write enable low
Read timing parameters during command write operations mode are the same as during read-only operations mode. Typical values at Vcc=3.3V, Ta=25C
11
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY AC ELECTRICAL CHARACTERISTICS (Ta = -40 ~ 85C, Vcc = 2.7V ~ 3.6V) Write Mode (F-CE# control)
Limits Vcc=2.7-3.6V 90ns Typ
Symbol
Parameter Min 90 50 0 50 0 10 30 0 0 60 30 90 90 0
Unit Max ns ns ns ns ns ns ns ns ns ns ns ns ns ns
tWC tAS tAH tDS tDH tOEH tRE tWS tWH tCEP tCEPH tGHEL tBLS tBLH
tAVAV tAVWH tEHAX tDVWH tEHDX tEHGL tWLEL tEHWH tELEH tEHEL tGHEL tPHHEH tQVPH
Write cycle time Address set-up time Address hold time Data set-up time Data hold time OE# hold from CE# high Latency between Read and Write FFH or 71H Write enable set-up time Write enable hold time CE# pulse width CE# pulse width high OE# hold to CE# Low
Block Lock set-up to chip enable high Block Lockhold from valid SRD tDAP tEHRH1 Duration of auto-program operation tDAE tEHRH2 Duration of auto-block erase operation tEHRL tEHRL CE# high to F-RY/BY# low tPS tPHWL RP# high recovery to write enable low
4 40 150
80 600 90
ms ms ns ns
Read timing parameters during command write operation mode are the same as during read-only operation mode. Typical values at Vcc=3.3V, Ta=25C
Erase and Program Performance
Parameter Block Erase Time Main Block Write Time (Page Mode) Page Write Time Min Typ 40 1.0 4 Max 600 1.8 80 Unit ms sec ms
Program Suspend Latency / Erase Suspend Time
Parameter Program Suspend Latency Erase Suspend Time
Please see page 19.
Min
Typ
Max 15 15
Unit s s
Vcc Power Up / Down Timing
Symbol tVCS
Please see page 12.
Parameter RP# =VIH set-up time from Vccmin
Min 2
Typ
Max
Unit s
During power up/down, by the noise pulses on control pins, the device has possibility of accidental erasure or programming. The device must be protected against initiation of write cycle for memory contents during power up/down. The delay time of min.2sec is always required before read operation or write operation is initiated from the time Vcc reaches Vccmin during power up/down. By holding RP# VIL, the contents of memory is protected during Vcc power up/down. During power up, RP# must be held VIL for min.2s from the time Vcc reaches Vccmin. During power down, RP# must be held VIL until Vcc reaches GND. RP# doesn't have latch mode ,therefore RP# must be held VIH during read operation or erase/program operation.
12
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
Vcc POWER UP / DOWN TIMING
Read /Write Inhibit Read /Write Inhibit Read /Write Inhibit
VCC
3.3V GND tVCS VIH VIL
RP#
CE#
VIH VIL tPS tPS
WE#
VIH VIL
AC WAVEFORMS FOR READ OPERATION AND TEST CONDITIONS
ADDRESSES
VIH VIL
ADDRESS VALID
TEST CONDITIONS FOR AC CHARACTERISTICS Input voltage : VIL = 0V, VIH = 3.0V Input rise and fall times : 5ns Reference voltage at timing measurement : 1.5V Output load : 1TTL gate +CL(30pF)
tRC ta (AD) ta (CE) tDF(CE)
CE#
VIH VIL
OE#
VIH VIL tOEH ta (OE) tOLZ HIGH-Z tPS tCLZ tDF(OE) or tOH HIGH-Z
1.3V 1N914 3.3k DUT CL
WE#
VIH VIL
DATA
VOH VOL
OUTPUT VALID
RP#
VIH VIL
tPHZ
AC WAVEFORMS FOR WRITE FFH or 71H AND READ OPERATION
VIH
ADDRESSES ADDRESS VALID
VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL DATA VOH HIGH-Z VOL tPS RP# VIH VIL
FFH or 71H
tRC ta (AD) ta (CE) tDF(CE)
tRE ta (OE) tOLZ tCLZ
tDF(OE) tOH
HIGH-Z
Valid
OUTPUT VALID
tPHZ
In the case of use CE# is Low fixed, it is allowed to define a timming specification of tRE from rising edge of WE# to falling edge of OE#, and valid data is read after spec of tRE+ta(CE). (This is only for FFH,71H program and read)
13
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY AC WAVEFORMS FOR PAGE PROGRAM OPERATION (WE# control)
VIH
A19~A7 VALID The other bank address VALID ADDRESS VALID
PROGRAM READ STATUS WRITE READ REGISTER ARRAY COMMAND
BANK ADDRESS VALID
VIL
A6~A0
VIH VIL tWC VIH VIL tCS tCH tWPH tOEH tGHWL ta(OE) tOEH tDAP VIH VIL
00H VALID 01H~7EH 7FH
tAS
tAH
ta(CE)
CE# OE#
ta(CE) ta(OE)
WE#
VIH VIL tWP
41H
DATA
VIH VIL tPS
tDS
DIN
tDH
DOUT DIN DIN SRD FFH
RP#
VIH VIL VIH VIL tBLS tBLH
WP1#, WP2#
AC WAVEFORMS FOR PAGE PROGRAM OPERATION (CE# control)
The other bank address VALID VALID ADDRESS VALID
PROGRAM READ STATUS WRITE READ REGISTER ARRAY COMMAND
VIH
A19~A7
BANK ADDRESS VALID
VIL VIH VIL tWC VIH VIL VIH VIL tCEP tWS tWH tOEH tGHEL
00H VALID 01H~7EH 7FH
A6~A0
tAS tCEPH
tAH ta(CE) ta(OE) tOEH tDAP
CE# OE#
ta(CE) ta(OE)
WE#
VIH VIL tDS
41H DIN
tDH
DOUT DIN DIN SRD FFH
DATA
VIH VIL tPS
RP# WP1#, WP2#
VIH VIL VIH VIL tBLS tBLH
14
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY AC WAVEFORMS FOR BYTE / WORD PROGRAM OPERATION (WE# control) (to only BANK(I))
PROGRAM ADDRESS VALID READ STATUS REGISTER WRITE READ ARRAY COMMAND
VIH ADDR VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL VIH RST# VIL
40H
BANK(I) ADDRESS VALID
tWC tCS
tAS
tAH
ta(CE) ta(OE) tOEH
tCH tWP tWPH tDS
DIN
SRD
FFH
tPS tBLS
tDH tDAP tBLH
WP1#, VIH WP2# VIL
AC WAVEFORMS FOR BYTE / WORD PROGRAM OPERATION (CE# control)
PROGRAM ADDRESS VALID
(to only BANK(I))
WRITE READ ARRAY COMMAND
VIH ADDR VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL VIH RP# VIL WP1#, VIH WP2# VIL
40H
READ STATUS REGISTER
BANK(I) ADDRESS VALID
tWC
tAS
tAH
ta(CE) ta(OE)
tCEP tWS tWH tDS
DIN
tOEH
SRD
FFH
tPS tBLS
tDH tDAP tBLH
15
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
AC WAVEFORMS FOR ERASE OPERATIONS (WE# control)
VIH
ADDRESSES
ERASE READ STATUS REGISTER WRITE READ ARRAY COMMAND
VIL tWC VIH CE# VIL tCS VIH OE# VIL VIH WE# VIL tWP VIH DATA
20H
ADDRESS VALID
BANK ADDRESS VALID
tAS
tAH
ta(CE)
tCH tOEH tDAE tDH
D0H
ta(OE)
tWPH
tDS
SRD
FFH
VIL tPS VIH VIL tBLS tBLH
RP# WP1#, WP2#
VIH VIL
AC WAVEFORMS FOR ERASE OPERATIONS (CE# control)
VIH
ADDRESSES
ERASE READ STATUS REGISTER WRITE READ ARRAY COMMAND
VIL tWC VIH CE# VIL tCEP VIH OE# VIL tWS VIH WE# VIL VIH DATA
20H
ADDRESS VALID
BANK ADDRESS VALID
tAS
tAH
ta(CE)
tCEPH tOEH
ta(OE)
tWH tDS
D0H
tDAE tDH
SRD FFH
VIL tPS VIH VIL tBLS tBLH
RP# WP1#, WP2#
VIH VIL
16
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
AC WAVEFORMS FOR PAGE PROGRAM OPERATION WITH BGO (WE# control)
Change Bank Address PROGRAM DATA TO ONE BANK
VIH
A19~A7 ADDRESS VALID
ARRAY READ FROM THE OTHER BANK WITH BGO
VALID
VALID
VIL VIH
00H 01H~7EH
~~ ~~
A6~A0
7FH
VALID
VALID
VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL
tWC tCS
tAS tCH tWP tWPH
tAH
ta(CE) ta(OE) tOEH
tDS
41H DIN
~ ~
~ ~
DIN
~~ ~~
DIN
SRD
DOUT
DOUT
tDH
AC WAVEFORMS FOR PAGE PROGRAM OPERATION WITH BGO (CE# control)
Change Bank Address PROGRAM DATA TO ONE BANK ARRAY READ FROM THE OTHER BANK WITH BGO
VIH
A19~A7 ADDRESS VALID
VALID
VALID
VIL VIH
A6~A0 00H 01H~7EH
~~ ~~
7FH
VALID
VALID
VIL VIH VIL
tWC
tAS tCEPH
tAH
ta(CE) ta(OE) tOEH
OE#
VIH VIL
tCEP tWS
VIL DATA VIH
41H DIN
tDS
DIN DIN SRD DOUT DOUT
VIL
tDH
17
~ ~
WE#
VIH
tCH
~ ~
CE#
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
AC WAVEFORMS FOR BYTE / WORD PROGRAM OPERATION WITH BGO (WE# control)
Change Bank Address PROGRAM DATA TO BANK(I) READ STATUS REGISTER ARRAY READ FROM BANK(II) WITH BGO
VIH
A19~A7
ADDRESS VALID
VALID
VALID
VIL VIH
A6~A0 VALID VALID VALID
VIL VIH VIL
tWC tCS
tAS tCH tWP tWPH
tAH
ta(CE) ta(OE)
CE#
OE#
VIH VIL
tOEH
WE#
VIH VIL VIH
tDS
40H DIN SRD DOUT DOUT
DATA VIL
tDH
AC WAVEFORMS FOR BYTE / WORD PROGRAM OPERATION WITH BGO (CE# control)
PROGRAM DATA TO BANK(I) READ STATUS REGISTER Change Bank Address ARRAY READ FROM BANK(II) WITH BGO
VIH
A19~A7
ADDRESS VALID
VALID
VALID
VIL VIH
A6~A0 VALID VALID VALID
VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL
tWC
tAS tCEPH
ta(CE) ta(OE) tOEH
tCEP tWS
tCH tDS
40H DIN SRD DOUT DOUT
tDH
18
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY AC WAVEFORMS FOR BLOCK ERASE OPERATION WITH BGO (WE# control)
Change Bank Address BLOCK ERASE IN ONE BANK READ STATUS REGISTER ARRAY READ FROM THE OTHER BANK WITH BGO
VIH ADDRESSES VIL
ADDRESS VALID
VALID
VALID
tWC
CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL
20H
tAS tCH tWP tWPH tOEH
tAH
ta(CE) ta(OE)
tCS
tDS
D0H SRD DOUT DOUT
tDH
AC WAVEFORMS FOR BLOCK ERASE OPERATION WITH BGO (CE# control)
Change Bank Address BLOCK ERASE IN ONE BANK READ STATUS REGISTER READ DATA FROM THE OTHER BANK WITH BGO
VIH ADDRESSES VIL CE# VIH VIL OE# VIH VIL WE# VIH VIL VIH DATA VIL
20H
ADDRESS VALID
VALID
VALID
tWC
tAS tCEPH
tAH
ta(CE) ta(OE)
tCEP tWS
tOEH tCH tDS
D0H SRD DOUT DOUT
tDH
19
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY AC WAVEFORMS FOR SUSPEND OPERATION (WE# control)
VIH
ADDRESSES
READ STATUS REGISTER
VIL VIH CE# VIL
BANK ADDRESS VALID
BANK ADDRESS VALID
tAS
tAH
ta(CE)
tCS VIH OE# VIL VIH WE# VIL tWP VIH DATA RP# WP1#, WP2#
B0H
tCH tOEH Program Suspend Latency
ta(OE)
S.R.6,7=1
VALID SRD
VIL VIH VIL VIH VIL tBLS tBLH
AC WAVEFORMS FOR SUSPEND OPERATION (CE# control)
VIH
ADDRESSES
READ STATUS REGISTER
VIL VIH CE# VIL VIH OE# VIL VIH WE# VIL VIH DATA
BANK ADDRESS VALID
BANK ADDRESS VALID
tAS tCEP
tAH
ta(CE)
ta(OE) tOEH Program Suspend Latency tWS tWH S.R.6,7=1
B0H VALID SRD
VIL VIH VIL tBLS tBLH
RP# WP1#, WP2#
VIH VIL
20
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY FULL STATUS CHECK PROCEDURE
STATUS REGISTER READ
LOCK BIT PROGRAM FLOW CHART
START
SR.4 =1 and SR.5 =1 ? NO
WRITE 77H YES COMMAND SEQUENCE ERROR WRITE D0H BLOCK ADDRESS
SR.5 = 0 ? NO YES
BLOCK ERASE ERROR SR.7 = 1 ? NO YES
SR.4 = 0 ? NO YES
PROGRAM ERROR (PAGE, LOCK BIT) SR.4 = 0 ? NO YES
LOCK BIT PROGRAM FAILED
SR.3 = 0 ? NO YES SUCCESSFUL (BLOCK ERASE, PROGRAM)
PROGRAM ERROR (BLOCK)
LOCK BIT PROGRAM SUCCESSFUL
BYTE PROGRAM FLOW CHART
START
PAGE PROGRAM FLOW CHART
START
WRITE 40H WRITE 41H
WRITE ADDRESS , DATA
n=0
STATUS REGISTER READ
WRITE ADDRESS n, DATA n
n = n+1
SR.7 = 1 ?
NO
WRITE B0H ?
NO
n = FFH ? or n = 7FH ? YES
NO
YES
YES
STATUS REGISTER READ
FULL STATUS CHECK IF DESIRED
SUSPEND LOOP WRITE D0H
YES SR.7 = 1 ? NO WRITE B0H ? NO
PAGE PROGRAM COMPLETED
* Word program is admitted to only BANK(I).
YES
YES
FULL STATUS CHECK IF DESIRED
SUSPEND LOOP WRITE D0H
YES
PAGE PROGRAM COMPLETED
21
Sep.1999. Rev4.0
MITSUBISHI LSIs
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY CLEAR PAGE BUFFER
START
SUSPEND / RESUME FLOW CHART
START
WRITE B0H WRITE 55H STATUS REGISTER READ WRITE D0H SR.7 = 1? NO PAGE BUFFER CLEAR COMPLETED YES
SUSPEND
SR.6 =1?
SINGLE DATA LOAD TO PAGE BUFFER
YES START WRITE FFH
NO
PROGRAM / ERASE COMPLETED
WRITE 74H
READ ARRAY DATA
WRITE ADDRESS , DATA
DONE READING ? YES
NO
DONE LOADING?
NO
WRITE D0H
RESUME
YES SINGLE DATA LOAD TO PAGE BUFFER COMPLETED
OPERATION RESUMED
* The bank address is required when writing this command. Also, there is no need to suspend the erase or program operation when reading data from the other bank. Please use BGO function.
PAGE BUFFER TO FLASH
START
BLOCK ERASE FLOW CHART
START
WRITE 20H WRITE 0EH WRITE D0H BLOCK ADDRESS WRITE D0H PAGE ADDRESS STATUS REGISTER READ STATUS REGISTER READ
NO NO SR.7 = 1 ? WRITE B0H ? NO SR.7 = 1 ?
WRITE B0H ?
NO
YES FULL STATUS CHECK IF DESIRED
YES FULL STATUS CHECK IF DESIRED
YES
SUSPEND LOOP WRITE D0H
YES
SUSPEND LOOP WRITE D0H
PAGE BUFFER TO FLASH COMPLETED YES
BLOCK ERASE COMPLETED
22
Sep.1999. Rev4.0
OPERATION STATUS and EFFECTIVE COMMAND
23 Clear Status Register
50H
Read/Standby State Read Status Register
90H 70H 70H 90H 71H 71H FFH FFH 70H 71H
Read Device Identifier
90H FFH
Read Lock Status
Read Array
Setup State Clear Page Buffer Setup
D0H 55H 74H
WD 0EH 41H 40H 77H
20H
A7H
Single Data Load to Page Buffer Setup
Page Buffer to Flash Setup
Page Program Setup
Byte Program Setup
WD D0H
Lock Bit Program Setup
Block Erase Setup
D0H
Erase All Unlocked Blocks Setup
OTHER
OTHER
D0H
Internal State
WDi i=0-127
OTHER
OTHER D0H
CMOS 3.3V-ONLY, BLOCK ERASE FLASH MEMORY
Program & Verify
Ready
Erase & Verify Read Status Register
D0H B0H B0H D0H
M5M29GB/T161BWG
16,777,216-BIT (1048,576-WORD BY16-BIT)
Read Status Register
Suspend State
Change Bank Address
Read Status Register
Change Bank Address
FFH 70H
70H
MITSUBISHI LSIs
Read State with BGO Read Array
(From The Other Bank)
Sep.1999. Rev4.0
Read Array

▲Up To Search▲

Price & Availability of M5M29GB

	To Download M5M29GB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .