View STQ-1016_232672.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Product Description
The Sirenza Microdevices' STQ-1016 is a direct quadrature modulator targeted for use in a wide range of communications systems, including cellular/PCS, GSM, CDMA, TETRA, and ISM datacom. This device features a wide 250 - 1000 MHz operating frequency band, excellent carrier and sideband suppression, and a low broadband noise floor. The STQ-1016 uses silicon germanium (SiGe) device technology and delivers a typical output power of -9 dBm with greater than 60dB IM3 suppression. A digital input shut-down feature is included that, when enabled, attenuates the output by 60dB. The device is packaged in an industry standard 16 pin TSSOP with exposed paddle for superb RF and thermal ground.
STQ-1016
250 - 1000 MHz Direct Quadrature Modulator
16 pin TSSOP with Exposed Ground Pad
Package Footprint: 0.197 x 0.252 inches, (5.0 x 6.4 mm) Package Height: 0.039 inches (1.0 mm)
Product Features
* * * * * * * * *
Excellent carrier feedthrough, -38 dBm constant over output power Output P1dB +5dBm Very low noise floor, -154 dBm/Hz typical Wide baseband input, DC - 500 MHz Superb phase accuracy and amplitude balance, 0.5 deg./0.2 dB Low LO drive requirement, -5 dBm Cellular/PCS/GSM/CDMA transceivers TETRA GMSK, QPSK, QAM, SSB modulators
Units MHz dBm dB dBm dBm dB 34 58 -2 -0.2 +4.75 +3 Min. 250 -12.0 -9 >10, 250 to 1000 MHz >15, 275 to 500 MHz +6 -38 42 62 -154 0.5 0.05 +5 80 25 +2 +0.2 +5.25 86 -30 Typ. Max. 1000 -7
Functional Block Diagram
BBQP VCC VEE LOP LON VEE SD BBIP 1 2 3 4 5 6 7 8 LO QUADRATURE GENERATOR 16 15 14 13 12 11 10 9 BBQN VCC VEE RFP RFN VEE VCC BBIN
Applications
Product Specifications - RF Output: TA = 25C
Parameters RF Frequency Range Output Power RF Port Return Loss Output P1dB Carrier Feedthrough Sideband Suppression IM3 Suppression Broadband Noise Floor Quadrature Phase Error I/Q Amplitude Balance Supply Voltage (Vcc) Supply Current Device Thermal Resistance junction-case
Test Conditions (see page 2) (baseband input level 600 mVp-p differential) matched to 50 using schematic shown on page 5 (baseband input level 3.8Vp-p differential typical)
2-tone BB input @ 600mVp-p diff. per tone, 20kHz spacing baseband inputs tied to 1.9VDC, -20MHz offset from carrier
dB dBm/Hz deg dB V mA C/W
Performance tests and ratings for Sirenza Microdevices' products were performed internally by Sirenza and measured using specific computer systems and/or components and reflect the approximate performance of the products as measured by those tests. Any difference in circuit implementation, test software, or test equipment may affect actual performance. The information provided herein is believed to be reliable at press time and Sirenza Microdevices assumes no responsibility for the use of this information. All such use shall be entirely at the user's own risk. Prices and specifications for Sirenza Microdevices' products are subject to change without notice. Buyers should consult Sirenza Microdevices' standard terms and conditions of sale for Sirenza's limited warranty with regard to its products. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. Sirenza Microdevices does not authorize or warrant any product for use in life-support devices and/or systems. Copyright 2004 Sirenza Microdevices, Inc. All worldwide rights reserved.
303 South Technology Court Broomfield, CO 80021
Phone: (800) SMI-MMIC 1
http://www.sirenza.com EDS-102531 Rev A
STQ-1016 Direct Quadrature Modulator
Test Conditions
VCC (pins 2,10,15) TA Baseband Input (Pins 1, 8, 9, 16) LO Input (Pins 4, 5)
(for all product specification tables unless otherwise noted) +5V +25C 1.9V DC bias, 200kHz frequency, 300mVp-p per pin = 600mVp-p differential drive, I and Q signals in quadrature -5dBm @ 250 to 1000 MHz
Product Specifications - Baseband Modulation Input: TA = 25C
Parameters Baseband Frequency Input Baseband Input Resistance Baseband Input Capacitance Additional Test Conditions -3dB bandwidth, baseband inputs terminated in 50 ohms per pin per pin Unit MHz kohms pF Min. DC 4.4 0.5 Typ. Max. 500
Product Specifications - LO Input: TA = 25C
Parameters LO Frequency LO Drive Level LO Port Return Loss matched to 50 using schematic shown on page 5 Additional Test Conditions Unit MHz dBm dB Min. 250 -8 -5 >10, 250 to 1000 MHz >15, 275 to 500 MHz Typ. Max. 1000 -2
Product Specifications - Miscellaneous: TA = 25C
Parameters Shut-Down Supply Current Shut-Down Attenuation Shut-Down Pin Resistance Shut-Down Pin Capacitance Shut-down Control Voltage Thresholds Shut-Down Settling Time @ 1MHz @ 1MHz Shut-down disabled (normal operation) Shut-down enabled Additional Test Conditions Shut-down enabled Unit mA dB kohm pF V V ns 3.75 0.0 <450 Min. Typ. 45 60 11.9 5.2 Vcc 1.5 Max. 60
303 South Technology Court Broomfield, CO 80021
Phone: (800) SMI-MMIC 2
http://www.sirenza.com EDS-102531 Rev A
STQ-1016 Direct Quadrature Modulator 250 - 1000 MHz Typical Device Performance
SSB Power vs. LO Frequency
-8 -8.5 -9
Output P1dB [dBm] 5 4 3 2 1 0 -40C 25C +85C 6
Output P1dB v s. LO Frequency
SSB Power [dBm]
-9.5 -10 -10.5 -11 -11.5 -12 -12.5 -13 200 300 400 500 600 700 800 900 1000 LO Frequency [MHz] -40C 25C +85C
200
300
400
500
600
700
800
900
1000
LO Frequency [MHz ]
Carrier Feedthrough v s. LO Frequency
-30 -32
Sideband Suppression vs. LO Frequency
50 48 Sideband Suppression [dB] 46 44 42 40 38 36 34 32 30 -40C 25C +85C 200 300 400 500 600 700 800 900 1000
Carrier Feedthrough [dBm]
-34 -36 -38 -40 -42 -44 -46 -48 -50 200 -40C 25C +85C 300 400 500 600 700 800 900 1000
LO Frequency [MHz]
LO Frequency [MHz]
0 -10 SSB Output Power[dBm] -20 -30
Intermodulation Distortion vs. BB Input Level @ 380MHz
0 -5 -10 |S11| [dB] -15 -20 -25 -30 200 300
RF & LO Port Match (for schematic show n on page 5)
RF Port LO Port
-40 -50 -60 -70 -80 -90 -100 -12.0 -10.0 -8.0 -6.0 -4.0 -2.0 0.0 2.0 4.0
fundamental (each tone) IM3 (each tone)
BB Input Level [dBVp-p diff.]
400
500
600
700
800
900
1000
Frequency [MHz]
303 South Technology Court Broomfield, CO 80021
Phone: (800) SMI-MMIC 3
http://www.sirenza.com EDS-102531 Rev A
Package Dimensions ("16" Package)
Dimensions in inches (mm)
STQ-1016 Direct Quadrature Modulator
STQ STQ 1016 2016 LOT ID XZZZZ
Suggested PCB Pad Layout
Part # Lot #
0.012 (0.30) 0.024 (0.63) 0.049 (1.25) 0.118 (3.0)
0.014 (0.35)
NOTES: 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH PROTRUSIONS OR GATE BURRS. 2. TOLERANCE .004" (0.1mm) UNLESS OTHERWISE SPECIFIED. 3. COPLANARITY: .004" (0.1mm) 4. CONTROLLING DIMENSION IS MILLIMETER, CONVERTED INCH DIMENSIONS ARE NOT NECESSARILY EXACT. 5. FOLLOWED FROM JEDEC MO-153.
0 8
0.118 (3.0) 0.010 (0.25) via 0.028 (0.7)
0.035 (0.9) 0.272 (6.9) all units are in inches (mm) - vias connect pad to underlying ground plane
- Indicates metalization
Pin Out Description
Pin # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Function BBQP VCC VEE LOP LON VEE SD BBIP BBIN VCC VEE RFN RFP VEE VCC BBQN Parameters Supply Voltage (VCC) LO, RF Input (LOP, LON, RFP, RFN) Baseband Min Input Voltage (BBIP, BBIN, BBQP, BBQN) Baseband Max Input Voltage (BBIP, BBIN, BBQP, BBQN) Operating Temperature Storage Temperature Description Q-channel baseband input, positive terminal Positive supply (+5V) Ground Local oscillator input, positive terminal Local oscillator input, negative terminal Ground Shut-down control I-channel baseband input, positive terminal I-channel baseband input, negative terminal Positive supply (+5V) Ground RF output, negative terminal RF output, positive terminal Ground Positive supply (+5V) Q-channel baseband input, negative terminal Value 6.0 +10 0 3 -40 to +85 -65 to +150 Unit VDC dBm VDC VDC C C Nominal DC bias voltage is 1.9V (biased internally) Nominal DC voltage is 2.4V. Output should be AC-coupled. Nominal DC voltage is 2.4V. Output should be AC-coupled. Logic high = normal operation; logic low = shut-down enabled. Nominal DC bias voltage is 1.9V (biased internally) Nominal DC bias voltage is 1.9V (biased internally) Nominal DC voltage is 2.0V. Input should be AC-coupled. Nominal DC voltage is 2.0V. Input should be AC-coupled. Additional Comments Nominal DC bias voltage is 1.9V (biased internally)
Absolute Maximum Ratings
Part Number Ordering Information
Devices/Reel Part Number STQ-1016 Reel Size 7" Min. 500 Max. 1000
Moisture Sensitivity Level 1 - no special handling required.
Operation of this device beyond any one of these limits may cause permanent damage. For reliable continuous operation the device voltage and current must not exceed the maximum operating values specified in the table on page one. 303 South Technology Court Broomfield, CO 80021 Phone: (800) SMI-MMIC 4
Caution: ESD Sensitive
Appropriate precaution in handling, packaging and testing devices must be observed.
http://www.sirenza.com EDS-102531 Rev A
250 - 1000 MHz Application Schematic
STQ-1016 Direct Quadrature Modulator
BBQP
P8
P9
BBQN
V CC
H1
1 2
L1 V CC V CC C3 1 C6 P10 2 3 4 T3 1 5 C5 C17 C4 BBQP V CC V EE U1 BBQN V CC V EE 16 15 14 C9 C10 5 T4 4 C1 6 C18 V CC Connec t bac kside expos ed paddle to RF/DC ground. R8 R9 R10 3 1 P11 V CC R1 R7
LOin
3
4
13 LOP RFP STQ-1016 5 12 LON RFN 6 11 V EE V EE 7 10 V CC SD 8 9 BBIP BBIN
R Fout
Shut-dow n H2
1 2
SH1
V CC
BBIP
P12
P13
BBIN
Bill of Materials (for 250 - 1000 MHz Evaluation Board P/N STQ1016EVB)
Component Designator U1 P8, P9, P10, P11, P12, P13 H1, H2 T3, T4 L1 R1, R7, R9, R10 R8 C6, C18 C9, C17 C3 C4, C5, C10, C16 SH1 303 South Technology Court Broomfield, CO 80021 1:1 1uH 200 ohm 1 kohm 33pF 1nF 2.2uF 22pF Value Qty 1 6 2 2 1 4 1 2 2 1 4 1 Vendor SMDI Johnson Components AMP M/A COM Panasonic Venkel Venkel Venkel Venkel Venkel Venkel 3M Part Number STQ-1016 142-0701-851 640453-2 ETC1-1-13 ELJ-FA1R0KF2 CR1206-8W-2000T CR0603-16W-1001FT C0603COG500-330JNE C0603COG500-102JNE C1206Y5V160-225ZNE C0603COG500-220JNE 929950-00 Description SiGe Direct Quadrature Modulator SMA connector, end launch with tab, for .062" thick board 2-pin header, right angle RF transformer, 4.5 - 3000MHz Inductor, 1210 footprint, 10% tolerance Resistor, 1206 footprint, 1% tolerance Resistor, 0603 footprint, 1% tolerance Capacitor, 0603 footprint, COG dielectric, 5% tolerance Capacitor, 0603 footprint, COG dielectric, 5% tolerance Capacitor, 1206 footprint, Y5V dielectric, 16V rating Capacitor, 0603 footprint, COG dielectric, 5% tolerance Shunt for 2-pin header http://www.sirenza.com EDS-102531 Rev A
Phone: (800) SMI-MMIC 5
STQ-1016 Direct Quadrature Modulator
Direct Quadrature Modulator: General Test Set-Up
499 50 5.11K 10K 5.11K VC C 2K AD 8138 VC C 1K + VOC M 50 50 600m V p-p differential D C levels for BBIN , BBIP, BBQN , BBQP are 1.9V nom inal. The offset required to null carrier feedthrough is typically < 20m V.
200kH z sine 145m V am plitude 0 degree phase BBI 90 BBQ
24.9
499
STQ-1016
2K B B I+ B B ILO+ LOB B Q+ B B Q-
0
-4dBm LO
LO M atch
0 90
R F+ R F-
RF M atch
R F out
200kH z sine 145m V am plitude + 90 degree phase 50 5.11K 10K - for interm odulation tests, synthesizer set for 200kH z and 220kH z sine outputs on I and Q channels 5.11K VC C
499
2K
VC C 1K
AD 8138 + VOC M -
50
+ 5V
50
600m V p-p differential
24.9
499
2K
303 South Technology Court Broomfield, CO 80021
Phone: (800) SMI-MMIC 6
http://www.sirenza.com EDS-102531 Rev A

▲Up To Search▲

Price & Availability of STQ-1016

	To Download STQ-1016 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .