View LPC2141FBD64_242184.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers; up to 512 kB flash with ISP/IAP, USB 2.0 full-speed device, 10-bit ADC and DAC
Rev. 01 -- 3 October 2005 Preliminary data sheet
1. General description
The LPC2141/42/44/46/48 microcontrollers are based on a 16-bit/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, that combine microcontroller with embedded high-speed flash memory ranging from 32 kB to 512 kB. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 % with minimal performance penalty. Due to their tiny size and low power consumption, LPC2141/42/44/46/48 are ideal for applications where miniaturization is a key requirement, such as access control and point-of-sale. Serial communications interfaces ranging from a USB 2.0 Full-speed device, multiple UARTs, SPI, SSP to I2C-bus and on-chip SRAM of 8 kB up to 40 kB, make these devices very well suited for communication gateways and protocol converters, soft modems, voice recognition and low end imaging, providing both large buffer size and high processing power. Various 32-bit timers, single or dual 10-bit ADC(s), 10-bit DAC, PWM channels and 45 fast GPIO lines with up to nine edge or level sensitive external interrupt pins make these microcontrollers suitable for industrial control and medical systems.
2. Features
2.1 Key features
s 16-bit/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package. s 8 kB to 40 kB of on-chip static RAM and 32 kB to 512 kB of on-chip flash memory. 128-bit wide interface/accelerator enables high-speed 60 MHz operation. s In-System Programming/In-Application Programming (ISP/IAP) via on-chip boot loader software. Single flash sector or full chip erase in 400 ms and programming of 256 bytes in 1 ms. s EmbeddedICE RT and Embedded Trace interfaces offer real-time debugging with the on-chip RealMonitor software and high-speed tracing of instruction execution. s USB 2.0 Full-speed compliant device controller with 2 kB of endpoint RAM. In addition, the LPC2146/48 provides 8 kB of on-chip RAM accessible to USB by DMA. s One or two (LPC2141/42 vs. LPC2144/46/48) 10-bit ADCs provide a total of 6/14 analog inputs, with conversion times as low as 2.44 s per channel. s Single 10-bit DAC provides variable analog output (LPC2142/44/46/48 only). s Two 32-bit timers/external event counters (with four capture and four compare channels each), PWM unit (six outputs) and watchdog. s Low power Real-Time Clock (RTC) with independent power and 32 kHz clock input.
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
s Multiple serial interfaces including two UARTs (16C550), two Fast I2C-bus (400 kbit/s), SPI and SSP with buffering and variable data length capabilities. s Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses. s Up to 45 of 5 V tolerant fast general purpose I/O pins in a tiny LQFP64 package. s Up to 21 external interrupt pins available. s 60 MHz maximum CPU clock available from programmable on-chip PLL with settling time of 100 s. s On-chip integrated oscillator operates with an external crystal from 1 MHz to 25 MHz. s Power saving modes include Idle and Power-down. s Individual enable/disable of peripheral functions as well as peripheral clock scaling for additional power optimization. s Processor wake-up from Power-down mode via external interrupt or BOD. s Single power supply chip with POR and BOD circuits: x CPU operating voltage range of 3.0 V to 3.6 V (3.3 V 10 %) with 5 V tolerant I/O pads.
3. Ordering information
Table 1: Ordering information Package Name LPC2141FBD64 LPC2142FBD64 LPC2144FBD64 LPC2146FBD64 LPC2148FBD64 LQFP64 Description plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm Version SOT314-2 Type number
3.1 Ordering options
Table 2: Ordering options Flash RAM memory 8 kB 16 kB 16 kB Endpoint USB RAM 2 kB 2 kB 2 kB ADC (channels overall) 1 (6 channels) 1 (6 channels) 2 (14 channels) 2 (14 channels) DAC 1 1 1 Temperature range (C) -40 to +85 -40 to +85 -40 to +85 -40 to +85 Type number
LPC2141FBD64 32 kB LPC2142FBD64 64 kB LPC2144FBD64 128 kB LPC2146FBD64 256 kB
32 kB + 8 kB 2 kB shared with USB DMA [1] 32 kB + 8 kB 2 kB shared with USB DMA [1]
LPC2148FBD64 512 kB
2 (14 channels)
1
-40 to +85
[1]
While the USB DMA is the primary user of the additional 8 kB RAM, this RAM is also accessible at any time by the CPU as a general purpose RAM for data and code storage.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
2 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
4. Block diagram
TMS(1) TDI(1) TRST(1) TCK(1) TDO(1) XTAL2 RST XTAL1
EMULATION TRACE MODULE
LPC2141/42/44/46/48
P0[31:28] and P0[25:0] P1[31:16]
TEST/DEBUG INTERFACE
PLL0 system clock PLL1 USB clock VECTORED INTERRUPT CONTROLLER SYSTEM FUNCTIONS
FAST GENERAL PURPOSE I/O
ARM7TDMI-S
AHB BRIDGE
ARM7 local bus
AMBA AHB (Advanced High-performance Bus) INTERNAL SRAM CONTROLLER INTERNAL FLASH CONTROLLER 8 kB RAM SHARED WITH USB DMA(3) AHB DECODER
8 kB/16 kB/ 32 kB SRAM
32 kB/64 kB/128 kB/ 256 kB/512 kB FLASH
AHB TO VPB BRIDGE
VPB DIVIDER
VPB (VLSI peripheral bus) EINT3 to EINT0 EXTERNAL INTERRUPTS
USB 2.0 FULL-SPEED DEVICE CONTROLLER WITH DMA(3)
D+ D- UP_LED CONNECT VBUS SCL0, SCL1
4 x CAP0 4 x CAP1 8 x MAT0 8 x MAT1 AD0[7:6] and AD0[4:1] AD1[7:0](2)
CAPTURE/COMPARE (W/EXTERNAL CLOCK) TIMER 0/TIMER 1
I2C-BUS SERIAL INTERFACES 0 AND 1
SDA0, SDA1
SCK0, SCK1 A/D CONVERTERS 0 AND 1(2) SPI AND SSP SERIAL INTERFACES MOSI0, MOSI1 MISO0, MISO1 SSEL0, SSEL1 TXD0, TXD1
AOUT(4)
D/A CONVERTER
UART0/UART1
RXD0, RXD1
P0[31:28] and P0[25:0] P1[31:16]
GENERAL PURPOSE I/O
REAL-TIME CLOCK
DSR1(2),CTS1(2), RTS1(2), DTR1(2) DCD1(2),RI1(2) RTXC1 RTXC2 VBAT
PWM6 to PWM0
PWM0
WATCHDOG TIMER SYSTEM CONTROL
002aab560
(1) Pins shared with GPIO. (2) LPC2144/46/48 only. (3) USB DMA controller with 8 kB of RAM accessible as general purpose RAM and/or DMA is available in LPC2146/48 only. (4) LPC2142/44/46/48 only.
Fig 1. Block diagram
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
3 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
5. Pinning information
5.1 Pinning
54 P0.19/MAT1.2/MOSI1/CAP1.2 53 P0.18/CAP1.3/MISO1/MAT1.3 55 P0.20/MAT1.3/SSEL1/EINT3
58 P0.23/VBUS
52 P1.30/TMS
64 P1.27/TDO
56 P1.29/TCK
60 P1.28/TDI
57 RESET
62 XTAL1
61 XTAL2
63 VREF
P0.21/PWM5/CAP1.3 P0.22/CAP0.0/MAT0.0 RTXC1 P1.19/TRACEPKT3 RTXC2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4
1 2 3 4 5 6 7 8 9
49 VBAT
59 VSSA
51 VDD
50 VSS
48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/EINT2 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/MAT1.1 38 P0.12/MAT1.0 37 P0.11/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/CAP1.0 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4
LPC2141
D+ 10 D- 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16
P0.31/UP_LED/CONNECT 17
VSS 18
P0.0/TXD0/PWM1 19
P1.31/TRST 20
P0.1/RXD0/PWM3/EINT0 21
P0.2/SCL0/CAP0.0 22
VDD 23
P1.26/RTCK 24
VSS 25
P0.3/SDA0/MAT0.0/EINT1 26
P0.4/SCK0/CAP0.1/AD0.6 27
P1.25/EXTIN0 28
P0.5/MISO0/MAT0.1/AD0.7 29
P0.6/MOSI0/CAP0.2 30
P0.7/SSEL0/PWM2/EINT2 31
P1.24/TRACECLK 32
002aab733
Fig 2. LPC2141 pinning
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
4 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
54 P0.19/MAT1.2/MOSI1/CAP1.2
53 P0.18/CAP1.3/MISO1/MAT1.3
55 P0.20/MAT1.3/SSEL1/EINT3
58 P0.23/VBUS
52 P1.30/TMS
64 P1.27/TDO
56 P1.29/TCK
60 P1.28/TDI
57 RESET
62 XTAL1
61 XTAL2
63 VREF
P0.21/PWM5/CAP1.3 P0.22/CAP0.0/MAT0.0 RTXC1 P1.19/TRACEPKT3 RTXC2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4/AOUT
1 2 3 4 5 6 7 8 9
49 VBAT
59 VSSA
51 VDD
50 VSS
48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/EINT2 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/MAT1.1 38 P0.12/MAT1.0 37 P0.11/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/CAP1.0 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4
LPC2142
D+ 10 D- 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16
P0.31/UP_LED/CONNECT 17
VSS 18
P0.0/TXD0/PWM1 19
P1.31/TRST 20
P0.1/RXD0/PWM3/EINT0 21
P0.2/SCL0/CAP0.0 22
VDD 23
P1.26/RTCK 24
VSS 25
P0.3/SDA0/MAT0.0/EINT1 26
P0.4/SCK0/CAP0.1/AD0.6 27
P1.25/EXTIN0 28
P0.5/MISO0/MAT0.1/AD0.7 29
P0.6/MOSI0/CAP0.2 30
P0.7/SSEL0/PWM2/EINT2 31
P1.24/TRACECLK 32
002aab734
Fig 3. LPC2142 pinning
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
5 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
54 P0.19/MAT1.2/MOSI1/CAP1.2
53 P0.18/CAP1.3/MISO1/MAT1.3
55 P0.20/MAT1.3/SSEL1/EINT3
58 P0.23/VBUS
52 P1.30/TMS
64 P1.27/TDO
56 P1.29/TCK
60 P1.28/TDI
57 RESET
62 XTAL1
61 XTAL2
63 VREF
P0.21/PWM5/AD1.6/CAP1.3 P0.22/AD1.7/CAP0.0/MAT0.0 RTXC1 P1.19/TRACEPKT3 RTXC2 VSS VDDA P1.18/TRACEPKT2 P0.25/AD0.4/AOUT
1 2 3 4 5 6 7 8 9
49 VBAT
59 VSSA
51 VDD
50 VSS
48 P1.20/TRACESYNC 47 P0.17/CAP1.2/SCK1/MAT1.2 46 P0.16/EINT0/MAT0.2/CAP0.2 45 P0.15/RI1/EINT2/AD1.5 44 P1.21/PIPESTAT0 43 VDD 42 VSS 41 P0.14/DCD1/EINT1/SDA1 40 P1.22/PIPESTAT1 39 P0.13/DTR1/MAT1.1/AD1.4 38 P0.12/DSR1/MAT1.0/AD1.3 37 P0.11/CTS1/CAP1.1/SCL1 36 P1.23/PIPESTAT2 35 P0.10/RTS1/CAP1.0/AD1.2 34 P0.9/RXD1/PWM6/EINT3 33 P0.8/TXD1/PWM4/AD1.1
LPC2144/2146/2148
D+ 10 D- 11 P1.17/TRACEPKT1 12 P0.28/AD0.1/CAP0.2/MAT0.2 13 P0.29/AD0.2/CAP0.3/MAT0.3 14 P0.30/AD0.3/EINT3/CAP0.0 15 P1.16/TRACEPKT0 16
P0.31/UP_LED/CONNECT 17
VSS 18
P0.0/TXD0/PWM1 19
P1.31/TRST 20
P0.1/RXD0/PWM3/EINT0 21
P0.2/SCL0/CAP0.0 22
VDD 23
P1.26/RTCK 24
VSS 25
P0.3/SDA0/MAT0.0/EINT1 26
P0.4/SCK0/CAP0.1/AD0.6 27
P1.25/EXTIN0 28
P0.5/MISO0/MAT0.1/AD0.7 29
P0.6/MOSI0/CAP0.2/AD1.0 30
P0.7/SSEL0/PWM2/EINT2 31
P1.24/TRACECLK 32
002aab735
Fig 4. LPC2144/2146/2148 pinning
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
6 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
5.2 Pin description
Table 3: Symbol P0.0 to P0.31 Pin description Pin Type I/O Description Port 0: Port 0 is a 32-bit I/O port with individual direction controls for each bit. Total of 31 pins of the Port 0 can be used as a general purpose bidirectional digital I/Os while P0.31 is output only pin. The operation of port 0 pins depends upon the pin function selected via the pin connect block. Pins P0.24, P0.26 and P0.27 are not available. P0.0/TXD0/ PWM1 19 [1] I/O O O P0.1/RXD0/ PWM3/EINT0 21 [2] I/O I O I P0.2/SCL0/ CAP0.0 22 [3] I/O I/O I P0.3/SDA0/ MAT0.0/EINT1 26 [3] I/O I/O O I P0.4/SCK0/ CAP0.1/AD0.6 27 [4] I/O I/O I I P0.5/MISO0/ MAT0.1/AD0.7 29 [4] I/O I/O O I P0.6/MOSI0/ CAP0.2/AD1.0 30 [4] I/O I/O I I P0.7/SSEL0/ PWM2/EINT2 31 [2] I/O I O I P0.8/TXD1/ PWM4/AD1.1 33 [4] I/O O O I
9397 750 14985
P0.0 -- General purpose input/output digital pin (GPIO). TXD0 -- Transmitter output for UART0. PWM1 -- Pulse Width Modulator output 1. P0.1 -- General purpose input/output digital pin (GPIO). RXD0 -- Receiver input for UART0. PWM3 -- Pulse Width Modulator output 3. EINT0 -- External interrupt 0 input P0.2 -- General purpose input/output digital pin (GPIO). SCL0 -- I2C0 clock input/output. Open-drain output (for I2C-bus compliance). CAP0.0 -- Capture input for Timer 0, channel 0. P0.3 -- General purpose input/output digital pin (GPIO). SDA0 -- I2C0 data input/output. Open-drain output (for I2C-bus compliance). MAT0.0 -- Match output for Timer 0, channel 0. EINT1 -- External interrupt 1 input. P0.4 -- General purpose input/output digital pin (GPIO). SCK0 -- Serial clock for SPI0. SPI clock output from master or input to slave. CAP0.1 -- Capture input for Timer 0, channel 0. AD0.6 -- ADC 0, input 6. P0.5 -- General purpose input/output digital pin (GPIO). MISO0 -- Master In Slave OUT for SPI0. Data input to SPI master or data output from SPI slave. MAT0.1 -- Match output for Timer 0, channel 1. AD0.7 -- ADC 0, input 7. P0.6 -- General purpose input/output digital pin (GPIO). MOSI0 -- Master Out Slave In for SPI0. Data output from SPI master or data input to SPI slave. CAP0.2 -- Capture input for Timer 0, channel 2. AD1.0 -- ADC 1, input 0. Available in LPC2144/46/48 only. P0.7 -- General purpose input/output digital pin (GPIO). SSEL0 -- Slave Select for SPI0. Selects the SPI interface as a slave. PWM2 -- Pulse Width Modulator output 2. EINT2 -- External interrupt 2 input. P0.8 -- General purpose input/output digital pin (GPIO). TXD1 -- Transmitter output for UART1. PWM4 -- Pulse Width Modulator output 4. AD1.1 -- ADC 1, input 1. Available in LPC2144/46/48 only.
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
7 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 3: Symbol
Pin description ...continued Pin 34 [2] Type I/O I O I Description P0.9 -- General purpose input/output digital pin (GPIO). RXD1 -- Receiver input for UART1. PWM6 -- Pulse Width Modulator output 6. EINT3 -- External interrupt 3 input. P0.10 -- General purpose input/output digital pin (GPIO). RTS1 -- Request to Send output for UART1. LPC2144/46/48 only. CAP1.0 -- Capture input for Timer 1, channel 0. AD1.2 -- ADC 1, input 2. Available in LPC2144/46/48 only. P0.11 -- General purpose input/output digital pin (GPIO). CTS1 -- Clear to Send input for UART1. Available in LPC2144/46/48 only. CAP1.1 -- Capture input for Timer 1, channel 1. SCL1 -- I2C1 clock input/output. Open-drain output (for I2C-bus compliance) P0.12 -- General purpose input/output digital pin (GPIO). DSR1 -- Data Set Ready input for UART1. Available in LPC2144/46/48 only. MAT1.0 -- Match output for Timer 1, channel 0. AD1.3 -- ADC input 3. Available in LPC2144/46/48 only. P0.13 -- General purpose input/output digital pin (GPIO). DTR1 -- Data Terminal Ready output for UART1. LPC2144/46/48 only. MAT1.1 -- Match output for Timer 1, channel 1. AD1.4 -- ADC input 4. Available in LPC2144/46/48 only. P0.14 -- General purpose input/output digital pin (GPIO). DCD1 -- Data Carrier Detect input for UART1. LPC2144/46/48 only. EINT1 -- External interrupt 1 input. SDA1 -- I2C1 data input/output. Open-drain output (for I2C-bus compliance) Note: LOW on this pin while RESET is LOW forces on-chip boot loader to take over control of the part after reset.
P0.9/RXD1/ PWM6/EINT3
P0.10/RTS1/ CAP1.0/AD1.2
35 [4]
I/O O I I
P0.11/CTS1/ CAP1.1/SCL1
37 [3]
I/O I I I/O
P0.12/DSR1/ MAT1.0/AD1.3
38 [4]
I/O I O I
P0.13/DTR1/ MAT1.1/AD1.4
39 [4]
I/O O O I
P0.14/DCD1/ EINT1/SDA1
41 [3]
I/O I I I/O
P0.15/RI1/ EINT2/AD1.5
45 [4]
I/O I I I
P0.15 -- General purpose input/output digital pin (GPIO). RI1 -- Ring Indicator input for UART1. Available in LPC2144/46/48 only. EINT2 -- External interrupt 2 input. AD1.5 -- ADC 1, input 5. Available in LPC2144/46/48 only. P0.16 -- General purpose input/output digital pin (GPIO). EINT0 -- External interrupt 0 input. MAT0.2 -- Match output for Timer 0, channel 2. CAP0.2 -- Capture input for Timer 0, channel 2. P0.17 -- General purpose input/output digital pin (GPIO). CAP1.2 -- Capture input for Timer 1, channel 2. SCK1 -- Serial Clock for SSP. Clock output from master or input to slave. MAT1.2 -- Match output for Timer 1, channel 2.
P0.16/EINT0/ MAT0.2/CAP0.2
46 [2]
I/O I O I
P0.17/CAP1.2/ SCK1/MAT1.2
47 [1]
I/O I I/O O
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
8 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 3: Symbol
Pin description ...continued Pin 53 [1] Type I/O I I/O O Description P0.18 -- General purpose input/output digital pin (GPIO). CAP1.3 -- Capture input for Timer 1, channel 3. MISO1 -- Master In Slave Out for SSP. Data input to SPI master or data output from SSP slave. MAT1.3 -- Match output for Timer 1, channel 3. P0.19 -- General purpose input/output digital pin (GPIO). MAT1.2 -- Match output for Timer 1, channel 2. MOSI1 -- Master Out Slave In for SSP. Data output from SSP master or data input to SSP slave. CAP1.2 -- Capture input for Timer 1, channel 2. P0.20 -- General purpose input/output digital pin (GPIO). MAT1.3 -- Match output for Timer 1, channel 3. SSEL1 -- Slave Select for SSP. Selects the SSP interface as a slave. EINT3 -- External interrupt 3 input. P0.21 -- General purpose input/output digital pin (GPIO). PWM5 -- Pulse Width Modulator output 5. AD1.6 -- ADC 1, input 6. Available in LPC2144/46/48 only. CAP1.3 -- Capture input for Timer 1, channel 3. P0.22 -- General purpose input/output digital pin (GPIO). AD1.7 -- ADC 1, input 7. Available in LPC2144/46/48 only. CAP0.0 -- Capture input for Timer 0, channel 0. MAT0.0 -- Match output for Timer 0, channel 0. P0.23 -- General purpose input/output digital pin (GPIO). VBUS -- Indicates the presence of USB bus power. Note: This signal must be HIGH for USB reset to occur. P0.25 -- General purpose input/output digital pin (GPIO). AD0.4 -- ADC 0, input 4. AOUT -- DAC output. Available in LPC2142/44/46/48 only. P0.28 -- General purpose input/output digital pin (GPIO). AD0.1 -- ADC 0, input 1. CAP0.2 -- Capture input for Timer 0, channel 2. MAT0.2 -- Match output for Timer 0, channel 2. P0.29 -- General purpose input/output digital pin (GPIO). AD0.2 -- ADC 0, input 2. CAP0.3 -- Capture input for Timer 0, Channel 3. MAT0.3 -- Match output for Timer 0, channel 3. P0.30 -- General purpose input/output digital pin (GPIO). AD0.3 -- ADC 0, input 3. EINT3 -- External interrupt 3 input. CAP0.0 -- Capture input for Timer 0, channel 0.
P0.18/CAP1.3/ MISO1/MAT1.3
P0.19/MAT1.2/ MOSI1/CAP1.2
54 [1]
I/O O I/O I
P0.20/MAT1.3/ SSEL1/EINT3
55 [2]
I/O O I I
P0.21/PWM5/ AD1.6/CAP1.3
1 [4]
I/O O I I
P0.22/AD1.7/ CAP0.0/MAT0.0
2 [4]
I/O I I O
P0.23/VBUS
58 [1]
I/O I
P0.25/AD0.4/ AOUT
9 [5]
I/O I O
P0.28/AD0.1/ CAP0.2/MAT0.2
13 [4]
I/O I I O
P0.29/AD0.2/ CAP0.3/MAT0.3
14 [4]
I/O I I O
P0.30/AD0.3/ EINT3/CAP0.0
15 [4]
I/O I I I
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
9 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 3: Symbol
Pin description ...continued Pin Type O O Description P0.31 -- General purpose output only digital pin (GPO). UP_LED -- USB GoodLink LED indicator. It is LOW when device is configured (non-control endpoints enabled). It is HIGH when the device is not configured or during global suspend. CONNECT -- Signal used to switch an external 1.5 k resistor under the software control. Used with the SoftConnect USB feature. Important: This is an digital output only pin. This pin MUST NOT be externally pulled LOW when RESET pin is LOW or the JTAG port will be disabled.
P0.31/UP_LED/ 17 [6] CONNECT
O
P1.0 to P1.31
I/O
Port 1: Port 1 is a 32-bit bidirectional I/O port with individual direction controls for each bit. The operation of port 1 pins depends upon the pin function selected via the pin connect block. Pins 0 through 15 of port 1 are not available. P1.16 -- General purpose input/output digital pin (GPIO). TRACEPKT0 -- Trace Packet, bit 0. Standard I/O port with internal pull-up. P1.17 -- General purpose input/output digital pin (GPIO). TRACEPKT1 -- Trace Packet, bit 1. Standard I/O port with internal pull-up. P1.18 -- General purpose input/output digital pin (GPIO). TRACEPKT2 -- Trace Packet, bit 2. Standard I/O port with internal pull-up. P1.19 -- General purpose input/output digital pin (GPIO). TRACEPKT3 -- Trace Packet, bit 3. Standard I/O port with internal pull-up. P1.20 -- General purpose input/output digital pin (GPIO). TRACESYNC -- Trace Synchronization. Standard I/O port with internal pull-up. Note: LOW on this pin while RESET is LOW enables pins P1.25:16 to operate as Trace port after reset.
P1.16/ TRACEPKT0 P1.17/ TRACEPKT1 P1.18/ TRACEPKT2 P1.19/ TRACEPKT3 P1.20/ TRACESYNC
16 [6] 12 [6] 8 [6] 4 [6] 48 [6]
I/O O I/O O I/O O I/O O I/O O
P1.21/ PIPESTAT0 P1.22/ PIPESTAT1 P1.23/ PIPESTAT2 P1.24/ TRACECLK P1.25/EXTIN0 P1.26/RTCK
44 [6] 40 [6] 36 [6] 32 [6] 28 [6] 24 [6]
I/O O I/O O I/O O I/O O I/O I I/O I/O
P1.21 -- General purpose input/output digital pin (GPIO). PIPESTAT0 -- Pipeline Status, bit 0. Standard I/O port with internal pull-up. P1.22 -- General purpose input/output digital pin (GPIO). PIPESTAT1 -- Pipeline Status, bit 1. Standard I/O port with internal pull-up. P1.23 -- General purpose input/output digital pin (GPIO). PIPESTAT2 -- Pipeline Status, bit 2. Standard I/O port with internal pull-up. P1.24 -- General purpose input/output digital pin (GPIO). TRACECLK -- Trace Clock. Standard I/O port with internal pull-up. P1.25 -- General purpose input/output digital pin (GPIO). EXTIN0 -- External Trigger Input. Standard I/O with internal pull-up. P1.26 -- General purpose input/output digital pin (GPIO). RTCK -- Returned Test Clock output. Extra signal added to the JTAG port. Assists debugger synchronization when processor frequency varies. Bidirectional pin with internal pull-up. Note: LOW on RTCK while RESET is LOW enables pins P1.31:26 to operate as Debug port after reset.
P1.27/TDO
64 [6]
I/O O
P1.27 -- General purpose input/output digital pin (GPIO). TDO -- Test Data out for JTAG interface.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
10 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 3: Symbol P1.28/TDI P1.29/TCK P1.30/TMS
Pin description ...continued Pin 60 [6] 56 [6] 52 [6] 20 [6] 10 [7] 11 [7] 57 [8] Type I/O I I/O I I/O I I/O I I/O I/O I Description P1.28 -- General purpose input/output digital pin (GPIO). TDI -- Test Data in for JTAG interface. P1.29 -- General purpose input/output digital pin (GPIO). TCK -- Test Clock for JTAG interface. P1.30 -- General purpose input/output digital pin (GPIO). TMS -- Test Mode Select for JTAG interface. P1.31 -- General purpose input/output digital pin (GPIO). TRST -- Test Reset for JTAG interface. USB bidirectional D+ line. USB bidirectional D- line. External reset input: A LOW on this pin resets the device, causing I/O ports and peripherals to take on their default states, and processor execution to begin at address 0. TTL with hysteresis, 5 V tolerant. Input to the oscillator circuit and internal clock generator circuits. Output from the oscillator amplifier. Input to the RTC oscillator circuit. Output from the RTC oscillator circuit. Ground: 0 V reference. Analog ground: 0 V reference. This should nominally be the same voltage as VSS, but should be isolated to minimize noise and error. 3.3 V power supply: This is the power supply voltage for the core and I/O ports. Analog 3.3 V power supply: This should be nominally the same voltage as VDD but should be isolated to minimize noise and error. This voltage is only used to power the on-chip ADC(s) and DAC. A/D converter reference voltage: This should be nominally less than or equal to the VDD voltage but should be isolated to minimize noise and error. Level on this pin is used as a reference for ADC(s) and DAC. RTC power supply voltage: 3.3 V on this pin supplies the power to the RTC.
P1.31/TRST D+ D- RESET
XTAL1 XTAL2 RTXC1 RTXC2 VSS VSSA VDD VDDA
62 [9] 61 [9] 3 [9] 5 [9]
I O I O
6, 18, 25, 42, I 50 59 23, 43, 51 7 I I I
VREF
63
I
VBAT
[1] [2] [3] [4]
49
I
5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. 5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. If configured for an input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. Open-drain 5 V tolerant digital I/O I2C-bus 400 kHz specification compatible pad. It requires external pull-up to provide an output functionality. 5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog input function. If configured for an input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. When configured as an ADC input, digital section of the pad is disabled. 5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog output function. When configured as the DAC output, digital section of the pad is disabled. 5 V tolerant pad with built-in pull-up resistor providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. The pull-up resistor's value typically ranges from 60 k to 300 k. Pad is designed in accordance with the Universal Serial Bus (USB) specification, revision 2.0 (Full-speed and Low-speed mode only). 5 V tolerant pad providing digital input (with TTL levels and hysteresis) function only. Pad provides special analog functionality.
[5] [6] [7] [8] [9]
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
11 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6. Functional description
6.1 Architectural overview
The ARM7TDMI-S is a general purpose 32-bit microprocessor, which offers high performance and very low power consumption. The ARM architecture is based on Reduced Instruction Set Computer (RISC) principles, and the instruction set and related decode mechanism are much simpler than those of microprogrammed Complex Instruction Set Computers (CISC). This simplicity results in a high instruction throughput and impressive real-time interrupt response from a small and cost-effective processor core. Pipeline techniques are employed so that all parts of the processing and memory systems can operate continuously. Typically, while one instruction is being executed, its successor is being decoded, and a third instruction is being fetched from memory. The ARM7TDMI-S processor also employs a unique architectural strategy known as Thumb, which makes it ideally suited to high-volume applications with memory restrictions, or applications where code density is an issue. The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the ARM7TDMI-S processor has two instruction sets:
* The standard 32-bit ARM set. * A 16-bit Thumb set.
The Thumb set's 16-bit instruction length allows it to approach twice the density of standard ARM code while retaining most of the ARM's performance advantage over a traditional 16-bit processor using 16-bit registers. This is possible because Thumb code operates on the same 32-bit register set as ARM code. Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the performance of an equivalent ARM processor connected to a 16-bit memory system. The particular flash implementation in the LPC2141/42/44/46/48 allows for full speed execution also in ARM mode. It is recommended to program performance critical and short code sections (such as interrupt service routines and DSP algorithms) in ARM mode. The impact on the overall code size will be minimal but the speed can be increased by 30 % over Thumb mode.
6.2 On-chip flash program memory
The LPC2141/42/44/46/48 incorporate a 32 kB, 64 kB, 128 kB, 256 kB and 512 kB flash memory system respectively. This memory may be used for both code and data storage. Programming of the flash memory may be accomplished in several ways. It may be programmed In System via the serial port. The application program may also erase and/or program the flash while the application is running, allowing a great degree of flexibility for data storage field firmware upgrades, etc. Due to the architectural solution chosen for an on-chip boot loader, flash memory available for user's code on LPC2141/42/44/46/48 is 32 kB, 64 kB, 128 kB, 256 kB and 500 kB respectively. The LPC2141/42/44/46/48 flash memory provides a minimum of 100,000 erase/write cycles and 20 years of data-retention.
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
12 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.3 On-chip static RAM
On-chip static RAM may be used for code and/or data storage. The SRAM may be accessed as 8-bit, 16-bit, and 32-bit. The LPC2141, LPC2142/44 and LPC2146/48 provide 8 kB, 16 kB and 32 kB of static RAM respectively. In case of LPC2146/48 only, an 8 kB SRAM block intended to be utilized mainly by the USB can also be used as a general purpose RAM for data storage and code storage and execution.
6.4 Memory map
The LPC2141/42/44/46/48 memory map incorporates several distinct regions, as shown in Figure 5. In addition, the CPU interrupt vectors may be remapped to allow them to reside in either flash memory (the default) or on-chip static RAM. This is described in Section 6.19 "System control".
4.0 GB AHB PERIPHERALS 3.75 GB VPB PERIPHERALS 3.5 GB 3.0 GB 2.0 GB RESERVED ADDRESS SPACE BOOT BLOCK (12 kB REMAPPED FROM ON-CHIP FLASH MEMORY RESERVED ADDRESS SPACE
0xFFFF FFFF 0xF000 0000 0xE000 0000 0xC000 0000 0x8000 0000 0x7FFF FFFF 0x7FFF D000 0x7FFF CFFF 0x7FD0 2000 0x7FD0 1FFF 8 kB ON-CHIP USB DMA RAM (LPC2146/2148) RESERVED ADDRESS SPACE 32 kB ON-CHIP STATIC RAM (LPC2146/2148) 16 kB ON-CHIP STATIC RAM (LPC2142/2144) 8 kB ON-CHIP STATIC RAM (LPC2141) 0x7FD0 0000 0x7FCF FFFF 0x4000 8000 0x4000 7FFF 0x4000 4000 0x4000 3FFF 0x4000 2000 0x4000 1FFF 0x4000 0000 0x3FFF FFFF 0x0008 0000 0x0007 FFFF 0x0004 0000 0x0003 FFFF 0x0002 0000 0x0001 FFFF 0x0001 0000 0x0000 FFFF 0x0000 8000 0x0000 7FFF 0x0000 0000
1.0 GB RESERVED ADDRESS SPACE TOTAL OF 512 kB ON-CHIP NON-VOLATILE MEMORY (LPC2148) TOTAL OF 256 kB ON-CHIP NON-VOLATILE MEMORY (LPC2146) TOTAL OF 128 kB ON-CHIP NON-VOLATILE MEMORY (LPC2144) TOTAL OF 64 kB ON-CHIP NON-VOLATILE MEMORY (LPC2142) TOTAL OF 32 kB ON-CHIP NON-VOLATILE MEMORY (LPC2141) 0.0 GB
002aab558
Fig 5. LPC2141/42/44/46/48 memory map
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
13 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.5 Interrupt controller
The Vectored Interrupt Controller (VIC) accepts all of the interrupt request inputs and categorizes them as Fast Interrupt Request (FIQ), vectored Interrupt Request (IRQ), and non-vectored IRQ as defined by programmable settings. The programmable assignment scheme means that priorities of interrupts from the various peripherals can be dynamically assigned and adjusted. Fast interrupt request (FIQ) has the highest priority. If more than one request is assigned to FIQ, the VIC combines the requests to produce the FIQ signal to the ARM processor. The fastest possible FIQ latency is achieved when only one request is classified as FIQ, because then the FIQ service routine does not need to branch into the interrupt service routine but can run from the interrupt vector location. If more than one request is assigned to the FIQ class, the FIQ service routine will read a word from the VIC that identifies which FIQ source(s) is (are) requesting an interrupt. Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned to this category. Any of the interrupt requests can be assigned to any of the 16 vectored IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest. Non-vectored IRQs have the lowest priority. The VIC combines the requests from all the vectored and non-vectored IRQs to produce the IRQ signal to the ARM processor. The IRQ service routine can start by reading a register from the VIC and jumping there. If any of the vectored IRQs are pending, the VIC provides the address of the highest-priority requesting IRQs service routine, otherwise it provides the address of a default routine that is shared by all the non-vectored IRQs. The default routine can read another VIC register to see what IRQs are active.
6.5.1 Interrupt sources
Each peripheral device has one interrupt line connected to the Vectored Interrupt Controller, but may have several internal interrupt flags. Individual interrupt flags may also represent more than one interrupt source.
6.6 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one function. Configuration registers control the multiplexers to allow connection between the pin and the on chip peripherals. Peripherals should be connected to the appropriate pins prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any enabled peripheral function that is not mapped to a related pin should be considered undefined. The Pin Control Module with its pin select registers defines the functionality of the microcontroller in a given hardware environment. After reset all pins of Port 0 and Port 1 are configured as input with the following exceptions: If debug is enabled, the JTAG pins will assume their JTAG functionality; if trace is enabled, the Trace pins will assume their trace functionality. The pins associated with the I2C0 and I2C1 interface are open drain.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
14 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.7 Fast general purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate registers allow setting or clearing any number of outputs simultaneously. The value of the output register may be read back, as well as the current state of the port pins. LPC2141/42/44/46/48 introduce accelerated GPIO functions over prior LPC2000 devices:
* GPIO registers are relocated to the ARM local bus for the fastest possible I/O timing. * Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
* All GPIO registers are byte addressable. * Entire port value can be written in one instruction.
6.7.1 Features
* Bit-level set and clear registers allow a single instruction set or clear of any number of
bits in one port.
* Direction control of individual bits. * Separate control of output set and clear. * All I/O default to inputs after reset. 6.8 10-bit ADC
The LPC2141/42 contain one and the LPC2144/46/48 contain two analog to digital converters. These converters are single 10-bit successive approximation analog to digital converters. While ADC0 has six channels, ADC1 has eight channels. Therefore, total number of available ADC inputs for LPC2141/42 is 6 and for LPC2144/46/48 is 14.
6.8.1 Features
* * * * * * *
10 bit successive approximation analog to digital converter. Measurement range of 0 V to VREF (2.0 V VREF VDDA). Each converter capable of performing more than 400,000 10-bit samples per second. Every analog input has a dedicated result register to reduce interrupt overhead. Burst conversion mode for single or multiple inputs. Optional conversion on transition on input pin or timer match signal. Global Start command for both converters (LPC2142/44/46/48 only).
6.9 10-bit DAC
The DAC enables the LPC2141/42/44/46/48 to generate a variable analog output. The maximum DAC output voltage is the VREF voltage.
6.9.1 Features
* 10-bit DAC. * Buffered output. * Power-down mode available.
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
15 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
* Selectable speed versus power. 6.10 USB 2.0 device controller
The USB is a 4-wire serial bus that supports communication between a host and a number (127 max) of peripherals. The host controller allocates the USB bandwidth to attached devices through a token based protocol. The bus supports hot plugging, unplugging, and dynamic configuration of the devices. All transactions are initiated by the host controller. The LPC2141/42/44/46/48 is equipped with a USB device controller that enables 12 Mbit/s data exchange with a USB host controller. It consists of a register interface, serial interface engine, endpoint buffer memory and DMA controller. The serial interface engine decodes the USB data stream and writes data to the appropriate end point buffer memory. The status of a completed USB transfer or error condition is indicated via status registers. An interrupt is also generated if enabled. A DMA controller (available in LPC2146/48 only) can transfer data between an endpoint buffer and the USB RAM.
6.10.1 Features
* * * * *
Fully compliant with USB 2.0 Full-speed specification. Supports 32 physical (16 logical) endpoints. Supports control, bulk, interrupt and isochronous endpoints. Scalable realization of endpoints at run time. Endpoint maximum packet size selection (up to USB maximum specification) by software at run time.
* RAM message buffer size based on endpoint realization and maximum packet size. * Supports SoftConnect and GoodLink LED indicator. These two functions are sharing
one pin.
* * * *
Supports bus-powered capability with low suspend current. Supports DMA transfer on all non-control endpoints (LPC2146/48 only). One duplex DMA channel serves all endpoints (LPC2146/48 only). Allows dynamic switching between CPU controlled and DMA modes (only in LPC2146/48).
* Double buffer implementation for bulk and isochronous endpoints. 6.11 UARTs
The LPC2141/42/44/46/48 each contain two UARTs. In addition to standard transmit and receive data lines, the LPC2144/46/48 UART1 also provides a full modem control handshake interface. Compared to previous LPC2000 microcontrollers, UARTs in LPC2141/42/44/46/48 introduce a fractional baud rate generator for both UARTs, enabling these microcontrollers to achieve standard baud rates such as 115200 with any crystal frequency above 2 MHz. In addition, auto-CTS/RTS flow-control functions are fully implemented in hardware (UART1 in LPC2144/46/48 only).
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
16 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.11.1 Features
* * * *
16 byte Receive and Transmit FIFOs. Register locations conform to `550 industry standard. Receiver FIFO trigger points at 1, 4, 8, and 14 bytes Built-in fractional baud rate generator covering wide range of baud rates without a need for external crystals of particular values. control on both UARTs.
* Transmission FIFO control enables implementation of software (XON/XOFF) flow * LPC2144/46/48 UART1 equipped with standard modem interface signals. This
module also provides full support for hardware flow control (auto-CTS/RTS).
6.12 I2C-bus serial I/O controller
The LPC2141/42/44/46/48 each contain two I2C-bus controllers. The I2C-bus is bidirectional, for inter-IC control using only two wires: a serial clock line (SCL), and a serial data line (SDA). Each device is recognized by a unique address and can operate as either a receiver-only device (e.g., an LCD driver or a transmitter with the capability to both receive and send information (such as memory)). Transmitters and/or receivers can operate in either master or slave mode, depending on whether the chip has to initiate a data transfer or is only addressed. The I2C-bus is a multi-master bus, it can be controlled by more than one bus master connected to it. The I2C-bus implemented in LPC2141/42/44/46/48 supports bit rates up to 400 kbit/s (Fast I2C-bus).
6.12.1 Features
* * * * * *
Compliant with standard I2C-bus interface. Easy to configure as master, slave, or master/slave. Programmable clocks allow versatile rate control. Bidirectional data transfer between masters and slaves. Multi-master bus (no central master). Arbitration between simultaneously transmitting masters without corruption of serial data on the bus. one serial bus.
* Serial clock synchronization allows devices with different bit rates to communicate via * Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
* The I2C-bus can be used for test and diagnostic purposes. 6.13 SPI serial I/O controller
The LPC2141/42/44/46/48 each contain one SPI controller. The SPI is a full duplex serial interface, designed to handle multiple masters and slaves connected to a given bus. Only a single master and a single slave can communicate on the interface during a given data transfer. During a data transfer the master always sends a byte of data to the slave, and the slave always sends a byte of data to the master.
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
17 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.13.1 Features
* * * *
Compliant with SPI specification. Synchronous, Serial, Full Duplex, Communication. Combined SPI master and slave. Maximum data bit rate of one eighth of the input clock rate.
6.14 SSP serial I/O controller
The LPC2141/42/44/46/48 each contain one SSP. The SSP controller is capable of operation on a SPI, 4-wire SSI, or Microwire bus. It can interact with multiple masters and slaves on the bus. However, only a single master and a single slave can communicate on the bus during a given data transfer. The SSP supports full duplex transfers, with data frames of 4 bits to 16 bits of data flowing from the master to the slave and from the slave to the master. Often only one of these data flows carries meaningful data.
6.14.1 Features
* Compatible with Motorola's SPI, TI's 4-wire SSI and National Semiconductor's
Microwire buses.
* * * *
Synchronous serial communication. Master or slave operation. 8-frame FIFOs for both transmit and receive. Four bits to 16 bits per frame.
6.15 General purpose timers/external event counters
The Timer/Counter is designed to count cycles of the peripheral clock (PCLK) or an externally supplied clock and optionally generate interrupts or perform other actions at specified timer values, based on four match registers. It also includes four capture inputs to trap the timer value when an input signal transitions, optionally generating an interrupt. Multiple pins can be selected to perform a single capture or match function, providing an application with `or' and `and', as well as `broadcast' functions among them. The LPC2141/42/44/46/48 can count external events on one of the capture inputs if the minimum external pulse is equal or longer than a period of the PCLK. In this configuration, unused capture lines can be selected as regular timer capture inputs, or used as external interrupts.
6.15.1 Features
* A 32-bit timer/counter with a programmable 32-bit prescaler. * External event counter or timer operation. * Four 32-bit capture channels per timer/counter that can take a snapshot of the timer
value when an input signal transitions. A capture event may also optionally generate an interrupt.
* Four 32-bit match registers that allow:
- Continuous operation with optional interrupt generation on match. - Stop timer on match with optional interrupt generation.
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
18 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
- Reset timer on match with optional interrupt generation.
* Four external outputs per timer/counter corresponding to match registers, with the
following capabilities: - Set LOW on match. - Set HIGH on match. - Toggle on match. - Do nothing on match.
6.16 Watchdog timer
The purpose of the watchdog is to reset the microcontroller within a reasonable amount of time if it enters an erroneous state. When enabled, the watchdog will generate a system reset if the user program fails to `feed' (or reload) the watchdog within a predetermined amount of time.
6.16.1 Features
* Internally resets chip if not periodically reloaded. * Debug mode. * Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
* * * *
Incorrect/Incomplete feed sequence causes reset/interrupt if enabled. Flag to indicate watchdog reset. Programmable 32-bit timer with internal pre-scaler. Selectable time period from (TPCLK x 256 x 4) to (TPCLK x 232 x 4) in multiples of TPCLK x 4.
6.17 Real-time clock
The RTC is designed to provide a set of counters to measure time when normal or idle operating mode is selected. The RTC has been designed to use little power, making it suitable for battery powered systems where the CPU is not running continuously (Idle mode).
6.17.1 Features
* Measures the passage of time to maintain a calendar and clock. * Ultra-low power design to support battery powered systems. * Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day
of Year.
* Can use either the RTC dedicated 32 kHz oscillator input or clock derived from the
external crystal/oscillator input at XTAL1. Programmable reference clock divider allows fine adjustment of the RTC.
* Dedicated power supply pin can be connected to a battery or the main 3.3 V.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
19 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.18 Pulse width modulator
The PWM is based on the standard timer block and inherits all of its features, although only the PWM function is pinned out on the LPC2141/42/44/46/48. The timer is designed to count cycles of the peripheral clock (PCLK) and optionally generate interrupts or perform other actions when specified timer values occur, based on seven match registers. The PWM function is also based on match register events. The ability to separately control rising and falling edge locations allows the PWM to be used for more applications. For instance, multi-phase motor control typically requires three non-overlapping PWM outputs with individual control of all three pulse widths and positions. Two match registers can be used to provide a single edge controlled PWM output. One match register (MR0) controls the PWM cycle rate, by resetting the count upon match. The other match register controls the PWM edge position. Additional single edge controlled PWM outputs require only one match register each, since the repetition rate is the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a rising edge at the beginning of each PWM cycle, when an MR0 match occurs. Three match registers can be used to provide a PWM output with both edges controlled. Again, the MR0 match register controls the PWM cycle rate. The other match registers control the two PWM edge positions. Additional double edge controlled PWM outputs require only two match registers each, since the repetition rate is the same for all PWM outputs. With double edge controlled PWM outputs, specific match registers control the rising and falling edge of the output. This allows both positive going PWM pulses (when the rising edge occurs prior to the falling edge), and negative going PWM pulses (when the falling edge occurs prior to the rising edge).
6.18.1 Features
* Seven match registers allow up to six single edge controlled or three double edge
controlled PWM outputs, or a mix of both types.
* The match registers also allow:
- Continuous operation with optional interrupt generation on match. - Stop timer on match with optional interrupt generation. - Reset timer on match with optional interrupt generation.
* Supports single edge controlled and/or double edge controlled PWM outputs. Single
edge controlled PWM outputs all go HIGH at the beginning of each cycle unless the output is a constant LOW. Double edge controlled PWM outputs can have either edge occur at any position within a cycle. This allows for both positive going and negative going pulses.
* Pulse period and width can be any number of timer counts. This allows complete
flexibility in the trade-off between resolution and repetition rate. All PWM outputs will occur at the same repetition rate.
* Double edge controlled PWM outputs can be programmed to be either positive going
or negative going pulses.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
20 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
* Match register updates are synchronized with pulse outputs to prevent generation of
erroneous pulses. Software must `release' new match values before they can become effective.
* May be used as a standard timer if the PWM mode is not enabled. * A 32-bit Timer/Counter with a programmable 32-bit Prescaler. 6.19 System control
6.19.1 Crystal oscillator
On-chip integrated oscillator operates with external crystal in range of 1 MHz to 25 MHz. The oscillator output frequency is called fosc and the ARM processor clock frequency is referred to as CCLK for purposes of rate equations, etc. fosc and CCLK are the same value unless the PLL is running and connected. Refer to Section 6.19.2 "PLL" for additional information.
6.19.2 PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input frequency is multiplied up into the range of 10 MHz to 60 MHz with a Current Controlled Oscillator (CCO). The multiplier can be an integer value from 1 to 32 (in practice, the multiplier value cannot be higher than 6 on this family of microcontrollers due to the upper frequency limit of the CPU). The CCO operates in the range of 156 MHz to 320 MHz, so there is an additional divider in the loop to keep the CCO within its frequency range while the PLL is providing the desired output frequency. The output divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. Since the minimum output divider value is 2, it is insured that the PLL output has a 50 % duty cycle. The PLL is turned off and bypassed following a chip reset and may be enabled by software. The program must configure and activate the PLL, wait for the PLL to Lock, then connect to the PLL as a clock source. The PLL settling time is 100 s.
6.19.3 Reset and wake-up timer
Reset has two sources on the LPC2141/42/44/46/48: the RESET pin and watchdog reset. The RESET pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of chip reset by any source starts the Wake-up Timer (see Wake-up Timer description below), causing the internal chip reset to remain asserted until the external reset is de-asserted, the oscillator is running, a fixed number of clocks have passed, and the on-chip flash controller has completed its initialization. When the internal reset is removed, the processor begins executing at address 0, which is the reset vector. At that point, all of the processor and peripheral registers have been initialized to predetermined values. The Wake-up Timer ensures that the oscillator and other analog functions required for chip operation are fully functional before the processor is allowed to execute instructions. This is important at power on, all types of reset, and whenever any of the aforementioned functions are turned off for any reason. Since the oscillator and other functions are turned off during Power-down mode, any wake-up of the processor from Power-down mode makes use of the Wake-up Timer.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
21 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
The Wake-up Timer monitors the crystal oscillator as the means of checking whether it is safe to begin code execution. When power is applied to the chip, or some event caused the chip to exit Power-down mode, some time is required for the oscillator to produce a signal of sufficient amplitude to drive the clock logic. The amount of time depends on many factors, including the rate of VDD ramp (in the case of power on), the type of crystal and its electrical characteristics (if a quartz crystal is used), as well as any other external circuitry (e.g. capacitors), and the characteristics of the oscillator itself under the existing ambient conditions.
6.19.4 Brownout detector
The LPC2141/42/44/46/48 include 2-stage monitoring of the voltage on the VDD pins. If this voltage falls below 2.9 V, the BOD asserts an interrupt signal to the VIC. This signal can be enabled for interrupt; if not, software can monitor the signal by reading dedicated register. The second stage of low voltage detection asserts reset to inactivate the LPC2141/42/44/46/48 when the voltage on the VDD pins falls below 2.6 V. This reset prevents alteration of the flash as operation of the various elements of the chip would otherwise become unreliable due to low voltage. The BOD circuit maintains this reset down below 1 V, at which point the POR circuitry maintains the overall reset. Both the 2.9 V and 2.6 V thresholds include some hysteresis. In normal operation, this hysteresis allows the 2.9 V detection to reliably interrupt, or a regularly-executed event loop to sense the condition.
6.19.5 Code security
This feature of the LPC2141/42/44/46/48 allow an application to control whether it can be debugged or protected from observation. If after reset on-chip boot loader detects a valid checksum in flash and reads 0x8765 4321 from address 0x1FC in flash, debugging will be disabled and thus the code in flash will be protected from observation. Once debugging is disabled, it can be enabled only by performing a full chip erase using the ISP.
6.19.6 External interrupt inputs
The LPC2141/42/44/46/48 include up to nine edge or level sensitive External Interrupt Inputs as selectable pin functions. When the pins are combined, external events can be processed as four independent interrupt signals. The External Interrupt Inputs can optionally be used to wake-up the processor from Power-down mode. Additionally capture input pins can also be used as external interrupts without the option to wake the device up from Power-down mode.
6.19.7 Memory mapping control
The Memory Mapping Control alters the mapping of the interrupt vectors that appear beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the on-chip flash memory, or to the on-chip static RAM. This allows code running in different memory spaces to have control of the interrupts.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
22 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
6.19.8 Power control
The LPC2141/42/44/46/48 supports two reduced power modes: Idle mode and Power-down mode. In Idle mode, execution of instructions is suspended until either a reset or interrupt occurs. Peripheral functions continue operation during Idle mode and may generate interrupts to cause the processor to resume execution. Idle mode eliminates power used by the processor itself, memory systems and related controllers, and internal buses. In Power-down mode, the oscillator is shut down and the chip receives no internal clocks. The processor state and registers, peripheral registers, and internal SRAM values are preserved throughout Power-down mode and the logic levels of chip output pins remain static. The Power-down mode can be terminated and normal operation resumed by either a reset or certain specific interrupts that are able to function without clocks. Since all dynamic operation of the chip is suspended, Power-down mode reduces chip power consumption to nearly zero. Selecting an external 32 kHz clock instead of the PCLK as a clock-source for the on-chip RTC will enable the microcontroller to have the RTC active during Power-down mode. Power-down current is increased with RTC active. However, it is significantly lower than in Idle mode. A Power Control for Peripherals feature allows individual peripherals to be turned off if they are not needed in the application, resulting in additional power savings during active and Idle mode.
6.19.9 VPB bus
The VPB divider determines the relationship between the processor clock (CCLK) and the clock used by peripheral devices (PCLK). The VPB divider serves two purposes. The first is to provide peripherals with the desired PCLK via VPB bus so that they can operate at the speed chosen for the ARM processor. In order to achieve this, the VPB bus may be slowed down to 12 to 14 of the processor clock rate. Because the VPB bus must work properly at power-up (and its timing cannot be altered if it does not work since the VPB divider control registers reside on the VPB bus), the default condition at reset is for the VPB bus to run at 14 of the processor clock rate. The second purpose of the VPB divider is to allow power savings when an application does not require any peripherals to run at the full processor rate. Because the VPB divider is connected to the PLL output, the PLL remains active (if it was running) during Idle mode.
6.20 Emulation and debugging
The LPC2141/42/44/46/48 support emulation and debugging via a JTAG serial port. A trace port allows tracing program execution. Debugging and trace functions are multiplexed only with GPIOs on Port 1. This means that all communication, timer and interface peripherals residing on Port 0 are available during the development and debugging phase as they are when the application is run in the embedded system itself.
6.20.1 EmbeddedICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of the target system requires a host computer running the debugger software and an EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts the remote debug protocol commands to the JTAG data needed to access the ARM core.
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
23 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
The ARM core has a Debug Communication Channel (DCC) function built-in. The DCC allows a program running on the target to communicate with the host debugger or another separate host without stopping the program flow or even entering the debug state. The DCC is accessed as a co-processor 14 by the program running on the ARM7TDMI-S core. The DCC allows the JTAG port to be used for sending and receiving data without affecting the normal program flow. The DCC data and control registers are mapped in to addresses in the EmbeddedICE logic.
6.20.2 Embedded trace
Since the LPC2141/42/44/46/48 have significant amounts of on-chip memory, it is not possible to determine how the processor core is operating simply by observing the external pins. The Embedded Trace Macrocell (ETM) provides real-time trace capability for deeply embedded processor cores. It outputs information about processor execution to the trace port. The ETM is connected directly to the ARM core and not to the main AMBA system bus. It compresses the trace information and exports it through a narrow trace port. An external trace port analyzer must capture the trace information under software debugger control. Instruction trace (or PC trace) shows the flow of execution of the processor and provides a list of all the instructions that were executed. Instruction trace is significantly compressed by only broadcasting branch addresses as well as a set of status signals that indicate the pipeline status on a cycle by cycle basis. Trace information generation can be controlled by selecting the trigger resource. Trigger resources include address comparators, counters and sequencers. Since trace information is compressed the software debugger requires a static image of the code being executed. Self-modifying code can not be traced because of this restriction.
6.20.3 RealMonitor
RealMonitor is a configurable software module, developed by ARM Inc., which enables real-time debug. It is a lightweight debug monitor that runs in the background while users debug their foreground application. It communicates with the host using the DCC, which is present in the EmbeddedICE logic. The LPC2141/42/44/46/48 contain a specific configuration of RealMonitor software programmed into the on-chip flash memory.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
24 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
7. Limiting values
Table 4: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). [1] Symbol VDD VDDA Vi(VBAT) Vi(VREF) Via VI Parameter supply voltage [2] voltage [3] for the RTC analog supply Conditions Min -0.5 -0.5 -0.5 -0.5 -0.5 5 V tolerant I/O pins other I/O pins IDD ISS Tstg Ptot(pack) DC supply current [8] DC ground current [10] based on package heat transfer, not device power consumption storage temperature [11] package total power dissipation
[5] [6]
Max +3.6 4.6 4.6 4.6 5.1 6.0
Unit V V V V V V
input voltage on pin VBAT input voltage on pin VREF analog input input voltage voltage [4]
-0.5 -0.5 -40 -
[5]
VDD + 0.5 [7] V 100 [9] 100 [9] 125 1.5 mA mA C W
[1]
The following applies to the Limiting values: a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum. b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted. Core and external rail. 3.3 V pad. On ADC related pins. Including voltage on outputs in 3-state mode. Only valid when the VDD supply voltage is present. Not to exceed 4.6 V. Per supply pin. The peak current is limited to 25 times the corresponding maximum current.
[2] [3] [4] [5] [6] [7] [8] [9]
[10] Per ground pin. [11] Dependent on package type.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
25 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
8. Static characteristics
Table 5: Static characteristics Ta = -40 C to +85 C for commercial applications, unless otherwise specified. Symbol VDD VDDA Vi(VBAT) Vi(VREF) IIL IIH IOZ Ilatch VI VO VIH VIL Vhys VOH VOL IOH IOL IOHS IOLS Ipd Ipu IDD(act) Parameter supply voltage [2] 3.3 V pad analog supply voltage input voltage on pin VBAT input voltage on pin VREF LOW-state input current HIGH-state input current OFF-state output current I/O latch-up current input voltage output voltage HIGH-state input voltage LOW-state input voltage hysteresis voltage HIGH-state output voltage [7] LOW-state output voltage [7] HIGH-state output current [7] LOW-state output current [7] HIGH-state short-circuit current [8] LOW-state short-circuit current [8] pull-down current pull-up current [10] IOH = -4 mA IOL = -4 mA VOH = VDD - 0.4 V VOL = 0.4 V VOH = 0 V VOL = VDDA VI = 5 V [9] VI = 0 V VDD < VI < 5 V [9] VI = 0 V; no pull-up VI = VDD; no pull-down VO = 0 V, VO = VDD; no pull-up/down -(0.5VDD) < V < (1.5VDD) Tj < 125 C pin configured to provide a digital function output active
[4] [5] [6]
Conditions
Min 3.0 3.0 2.0 [3] 2.5 0 0 2.0 VDD - 0.4 -4 4 10 -15 0
Typ [1] 3.3 3.3 3.3 3.3 0.4 50 -50 0
Max 3.6 3.6 3.6 VDDA 3 3 3 100 5.5 VDD 0.8 0.4 -45 50 150 -85 0
Unit V V V V A A A mA V V V V V V V mA mA mA mA A A A mA
Standard port pins, RESET, RTCK
active mode supply current VDD = 3.3 V, Ta = 25 C, code
while(1){}
executed from flash, no active peripherals CCLK = 10 MHz CCLK = 60 MHz (other parameters as above) IDD(pd) Power-down mode supply current VDD = 3.3 V, Ta = +25 C VDD = 3.3 V, Ta = +85 C mA A A
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
26 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 5: Static characteristics ...continued Ta = -40 C to +85 C for commercial applications, unless otherwise specified. Symbol IBATpd Parameter Conditions Min Typ [1] Max Unit A Power-down mode battery RTC clock = 32 kHz supply current [11] (from RTXC pins), Ta = +25 C VDD = 3.0 V, Vi(VBAT) = 2.5 V VDD = 3.0 V, Vi(VBAT) = 3.0 V IBATact active mode battery supply CCLK = 60 MHz, current [11] PCLK = 15 MHz, PCLK enabled to RTCK, RTC clock = 32 kHz (from RTXC pins), Ta = +25 C VDD = 3.0 V, Vi(VBAT) = 3.0 V IBATact(opt) optimized active mode battery supply current [11] [12] PCLK disabled to RTCK in the PCONP register, RTC clock = 32 kHz (from RTXC pins), Ta = +25 C, Vi(VBAT) = 3.3 V CCLK = 10 MHz CCLK = 60 MHz I2C-bus VIH VIL Vhys VOL ILI pins HIGH-state input voltage LOW-state input voltage hysteresis voltage LOW-state output voltage [7] input leakage current [13] IOLS = 3 mA VI = VDD VI = 5 V Oscillator pins Vi(XTAL1) Vo(XTAL2) Vi(RTXC1) Vo(RTXC2) USB pins IOZ VBUS VDI VCM Vth(rs)se OFF-state output current VBUS line input voltage on the USB connector differential input sensitivity |(D+) - (D-)| differential common-mode range single-ended receiver switching threshold voltage includes VDI range 0 V < VI < 3.3 V 0.2 0.8 0.8 10 5.25 2.5 2.0 A V V V V input voltage on pin XTAL1 output voltage on pin XTAL2 input voltage on pin RTXC1 output voltage on pin RTXC2 0 0 0 0 1.8 1.8 1.8 1.8 V V V V 0.7VDD(3V3) 2 10 V V V A A 0.3VDD(3V3) V 0.4 4 22 A A A A
0.5VDD(3V3) -
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
27 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
Table 5: Static characteristics ...continued Ta = -40 C to +85 C for commercial applications, unless otherwise specified. Symbol VOL VOH Ctrans ZDRV Parameter LOW output level HIGH output level transceiver capacitance driver output impedance for driver which is not high-speed capable pull-up resistance Conditions RL of 1.5 k to 3.6 V RL of 15 k to GND pin to GND steady state drive
[14]
Min 2.8 29
Typ [1] -
Max 0.3 3.6 20 44
Unit V V pF
Rpu
[1] [2] [3] [4] [5] [6] [7] [8] [9]
SoftConnect = ON
1.1
-
1.9
k
Typical ratings are not guaranteed. The values listed are at room temperature (+25 C), nominal supply voltages. Core and external rail. The RTC typically fails when Vi(VBAT) drops below 1.6 V. Including voltage on outputs in 3-state mode. VDD supply voltages must be present. 3-state outputs go into 3-state mode when VDD is grounded. Accounts for 100 mV voltage drop in all supply lines. Only allowed for a short time period. Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V.
[10] Applies to P1.16 to P1.31. [11] On pin VBAT. [12] Optimized for low battery consumption. [13] To VSS. [14] Includes external resistors of 18 1 % on D+ and D-.
Table 6: ADC static characteristics VDDA = 2.5 V to 3.6 V; Ta = -40 C to +85 C unless otherwise specified. ADC frequency 4.5 MHz. Symbol Via Cia ED EL(adj) EO EG ET Rvsi Parameter analog input voltage analog input capacitance differential linearity error integral non-linearity offset error gain error absolute error voltage source interface resistance
Conditions: VSSA = 0 V, VDDA = 3.3 V. The ADC is monotonic, there are no missing codes. The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 6. The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after appropriate adjustment of gain and offset errors. See Figure 6. The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the ideal curve. See Figure 6. The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset error, and the straight line which fits the ideal transfer curve. See Figure 6.
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Conditions
Min 0 [1] [2] [3] [1] [4] [1] [5] [1] [6] [1] [7] [8]
Typ -
Max VDDA 1 1 2 3 0.5 4 40
Unit V pF LSB LSB LSB % LSB k
-
[1] [2] [3] [4] [5] [6]
9397 750 14985
Preliminary data sheet
Rev. 01 -- 3 October 2005
28 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
[7] [8]
The absolute error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the non-calibrated ADC and the ideal transfer curve. See Figure 6. See Figure 7.
offset error EO 1023
gain error EG
1022
1021
1020
1019
1018
(2)
7 code out 6
(1)
5
(5)
4
(4)
3
(3)
2
1
1 LSB (ideal) 1018 1019 1020 1021 1022 1023 1024
0 1 offset error EO 2 3 4 5 6 7 Via (LSBideal)
1 LSB =
VDDA - VSSA 1024
002aab136
(1) Example of an actual transfer curve. (2) The ideal transfer curve. (3) Differential linearity error (ED). (4) Integral non-linearity (EL(adj)). (5) Center of a step of the actual transfer curve.
Fig 6. ADC characteristics
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
29 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
LPC2141/42/44/46/48
20 k
ADx.ySAMPLE
3 pF 5 pF
ADx.y
Rvsi
VEXT
VSS
002aab834
Fig 7. Suggested ADC interface - LPC2141/42/44/46/48 ADx.y pin
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
30 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
9. Dynamic characteristics
Table 7: Dynamic characteristics of USB pins (full-speed) CL = 50 pF; Rpu = 1.5 k on D+ to VDD,unless otherwise specified Symbol tr tf tFRFM VCRS tFEOPT tFDEOP tJR1 tJR2 tEOPR1 Parameter rise time fall time differential rise and fall time matching output signal crossover voltage source SE0 interval of EOP source jitter for differential transition to SE0 transition receiver jitter to next transition receiver jitter for paired transitions EOP width at receiver [1] 10 % to 90 % must reject as EOP; see Figure 9 must accept as EOP; see Figure 9 see Figure 9 see Figure 9 Conditions 10 % to 90 % 10 % to 90 % (tr/tf) Min 4 4 90 1.3 160 -2 -18.5 -9 40 Typ Max 20 20 110 2.0 175 +5 +18.5 +9 Unit ns ns % V ns ns ns ns ns
tEOPR2
EOP width at receiver [1]
82
-
-
ns
[1]
Characterized but not implemented as production test. Guaranteed by design.
Table 8: Dynamic characteristics Ta = -40 C to +85 C for commercial applications, VDD over specified ranges [1] Symbol External clock fosc Tcy(CLK) tCHCX tCLCX tCLCH tCHCL tr(o) tf(o) I2C-bus tf(o)
[1] [2] [3]
Parameter oscillator frequency clock cycle time clock HIGH time clock LOW time clock rise time clock fall time output rise time output fall time pins (P0.2, P0.3, P0.11, and P0.14) output fall time
Conditions
Min 10 40 Tcy(CLK) x 0.4 Tcy(CLK) x 0.4 -
Typ [2] 10 10 -
Max 25 100 5 5 -
Unit MHz ns ns ns ns ns ns ns ns
Port pins (P0.2, P0.3, P0.11, and P0.14)
VIH to VIL
20 + 0.1 x Cb [3]
Parameters are valid over operating temperature range unless otherwise specified. Typical ratings are not guaranteed. The values listed are at room temperature (+25 C), nominal supply voltages. Bus capacitance Cb in pF, from 10 pF to 400 pF.
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
31 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
9.1 Timing
VDD - 0.5 V 0.45 V
0.2VDD + 0.9 V 0.2VDD - 0.1 V tCHCX tCHCL tCLCX tCLCH Tcy(CLK)
002aaa907
Fig 8. External clock timing
tPERIOD crossover point differential data lines
crossover point extended
source EOP width: tFEOPT differential data to SEO/EOP skew n * tPERIOD + tFDEOP
receiver EOP width: tEOPR1, tEOPR2
002aab561
Fig 9. Differential data-to-EOP transition skew and EOP width
10. Application information
10.1 Suggested USB interface solutions
VDD
CONNECT soft-connect switch
LPC2142/2148
VBUS D+ D- VSS
RS = 33 RS = 33
R1 1.5 k
USB-B connector
002aab563
Fig 10. LPC2141/42/44/46/48 USB interface using the CONNECT function on pin 17
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
32 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
VDD
R2
LPC2141/42/ 44/46/48
UP_LED VBUS D+ D- VSS
RS = 33 RS = 33
R1 1.5 k
USB-B connector
002aab562
Fig 11. LPC2141/42/44/46/48 USB interface using the UP_LED function on pin 17
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
33 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
11. Package outline
LQFP64: plastic low profile quad flat package; 64 leads; body 10 x 10 x 1.4 mm SOT314-2
c
y X A 48 49 33 32 ZE
e E HE wM bp 64 1 pin 1 index 16 ZD bp D HD wM B vM B vM A 17 detail X L Lp A A2 A1 (A 3)
e
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.6 A1 0.20 0.05 A2 1.45 1.35 A3 0.25 bp 0.27 0.17 c 0.18 0.12 D (1) 10.1 9.9 E (1) 10.1 9.9 e 0.5 HD HE L 1 Lp 0.75 0.45 v 0.2 w 0.12 y 0.1 Z D (1) Z E (1) 1.45 1.05 1.45 1.05 7o o 0
12.15 12.15 11.85 11.85
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT314-2 REFERENCES IEC 136E10 JEDEC MS-026 JEITA EUROPEAN PROJECTION
ISSUE DATE 00-01-19 03-02-25
Fig 12. Package outline SOT314-2 (LQFP64)
9397 750 14985 (c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
34 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
12. Abbreviations
Table 9: Acronym ADC BOD CPU DAC DCC DMA FIFO GPIO PLL POR PWM RAM SPI SRAM SSP UART USB VPB Acronym list Description Analog-to-Digital Converter Brown-Out Detection Central Processing Unit Digital-to-Analog Converter Debug Communications Channel Direct Memory Access First In, First Out General Purpose Input/Output Phase-Locked Loop Power-On Reset Pulse Width Modulator Random Access Memory Serial Peripheral Interface Static Random Access Memory Synchronous Serial Port Universal Asynchronous Receiver/Transmitter Universal Serial Bus VLSI Peripheral Bus
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
35 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
13. Revision history
Table 10: Revision history Release date 20051003 Data sheet status Preliminary data sheet Change notice Doc. number 9397 750 14985 Supersedes Document ID LPC2141_42_44_46_48_1
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
36 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
14. Data sheet status
Level I II Data sheet status [1] Objective data Preliminary data Product status [2] [3] Development Qualification Definition This data sheet contains data from the objective specification for product development. Philips Semiconductors reserves the right to change the specification in any manner without notice. This data sheet contains data from the preliminary specification. Supplementary data will be published at a later date. Philips Semiconductors reserves the right to change the specification without notice, in order to improve the design and supply the best possible product. This data sheet contains data from the product specification. Philips Semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. Relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN).
III
Product data
Production
[1] [2] [3]
Please consult the most recently issued data sheet before initiating or completing a design. The product status of the device(s) described in this data sheet may have changed since this data sheet was published. The latest information is available on the Internet at URL http://www.semiconductors.philips.com. For data sheets describing multiple type numbers, the highest-level product status determines the data sheet status.
15. Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification.
customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status `Production'), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
17. Trademarks
Notice -- All referenced brands, product names, service names and trademarks are the property of their respective owners. I2C-bus -- wordmark and logo are trademarks of Koninklijke Philips Electronics N.V. SoftConnect -- is a trademark of Koninklijke Philips Electronics N.V.
16. Disclaimers
Life support -- These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors
18. Contact information
For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com
9397 750 14985
(c) Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Preliminary data sheet
Rev. 01 -- 3 October 2005
37 of 38
Philips Semiconductors
LPC2141/42/44/46/48
Single-chip 16-bit/32-bit microcontrollers
19. Contents
1 2 2.1 3 3.1 4 5 5.1 5.2 6 6.1 6.2 6.3 6.4 6.5 6.5.1 6.6 6.7 6.7.1 6.8 6.8.1 6.9 6.9.1 6.10 6.10.1 6.11 6.11.1 6.12 6.12.1 6.13 6.13.1 6.14 6.14.1 6.15 6.15.1 6.16 6.16.1 6.17 6.17.1 6.18 6.18.1 6.19 6.19.1 6.19.2 6.19.3 6.19.4 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7 Functional description . . . . . . . . . . . . . . . . . . 12 Architectural overview. . . . . . . . . . . . . . . . . . . 12 On-chip flash program memory . . . . . . . . . . . 12 On-chip static RAM. . . . . . . . . . . . . . . . . . . . . 13 Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 13 Interrupt controller . . . . . . . . . . . . . . . . . . . . . 14 Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 14 Pin connect block . . . . . . . . . . . . . . . . . . . . . . 14 Fast general purpose parallel I/O . . . . . . . . . . 15 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10-bit DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 USB 2.0 device controller . . . . . . . . . . . . . . . . 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 I2C-bus serial I/O controller . . . . . . . . . . . . . . 17 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 SPI serial I/O controller. . . . . . . . . . . . . . . . . . 17 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 SSP serial I/O controller . . . . . . . . . . . . . . . . . 18 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 General purpose timers/external event counters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . 19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Real-time clock . . . . . . . . . . . . . . . . . . . . . . . . 19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Pulse width modulator . . . . . . . . . . . . . . . . . . 20 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 System control . . . . . . . . . . . . . . . . . . . . . . . . 21 Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . 21 PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Reset and wake-up timer . . . . . . . . . . . . . . . . 21 Brownout detector. . . . . . . . . . . . . . . . . . . . . . 22 6.19.5 6.19.6 6.19.7 6.19.8 6.19.9 6.20 6.20.1 6.20.2 6.20.3 7 8 9 9.1 10 10.1 11 12 13 14 15 16 17 18 Code security . . . . . . . . . . . . . . . . . . . . . . . . . External interrupt inputs . . . . . . . . . . . . . . . . . Memory mapping control . . . . . . . . . . . . . . . . Power control . . . . . . . . . . . . . . . . . . . . . . . . . VPB bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emulation and debugging. . . . . . . . . . . . . . . . EmbeddedICE . . . . . . . . . . . . . . . . . . . . . . . . Embedded trace. . . . . . . . . . . . . . . . . . . . . . . RealMonitor . . . . . . . . . . . . . . . . . . . . . . . . . . Limiting values . . . . . . . . . . . . . . . . . . . . . . . . Static characteristics . . . . . . . . . . . . . . . . . . . Dynamic characteristics . . . . . . . . . . . . . . . . . Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Suggested USB interface solutions . . . . . . . . Package outline . . . . . . . . . . . . . . . . . . . . . . . . Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Data sheet status. . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . 22 22 22 23 23 23 23 24 24 25 26 31 32 32 32 34 35 36 37 37 37 37 37
(c) Koninklijke Philips Electronics N.V. 2005
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 3 October 2005 Document number: 9397 750 14985
Published in the Netherlands

▲Up To Search▲

Price & Availability of LPC2141FBD64

	To Download LPC2141FBD64 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .