 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Features Ultra Low SSB Phase Noise: -150 dBc/Hz Single-Ended I/O's Output Power: -2 to -3.5 dBm Single DC Supply: +3V @ 53 mA 9 mm2 Ultra Small Package: SOT26 Typical Applications Prescaler for DC to C Band PLL Applications: * UNII, Pt. - Pt. & VSAT Radios * 802.11a & HiperLAN WLAN 10 FREQ. DIVIDER & DETECTORS - SMT * Fiber Optic * Cellular / 3G Infrastructure Functional Diagram General Description The HMC433 is a low noise Divide-by-4 Static Divider utilizing InGaP GaAs HBT technology in an ultra small surface mount SOT26 plastic package. This device operates from DC (with a square wave input) to 8.0 GHz input frequency with a single +3.0V DC supply. Single-ended inputs and outputs reduce component count and cost. The low additive SSB phase noise of -150 dBc/Hz at 100 kHz offset helps the user maintain good system noise performance. Electrical Specifications, TA = +25 C, 50 Ohm System, Vcc= +3V Parameter Maximum Input Frequency Minimum Input Frequency Input Power Range Sine Wave Input. [1] Fin= 1 to 6 GHz Fin= 6 to 8 GHz Fin= 4 GHz Fin= 8 GHz RF Output Terminated, Fin= 4 GHz, Pin= 0 dBm Pin= 0 dBm, Fin= 4 GHz Pin= 0 dBm, Fout= 882 MHz Vcc= +3.0V -12 -3 -5.0 -6.5 Conditions Min. 8 Typ. 8.5 0.2 -15 -7 -2.0 -3.5 -25 -150 120 53 +12 +10 Max. Units GHz GHz dBm dBm dBm dBm dBm dBc/Hz ps mA Output Power Reverse Leakage SSB Phase Noise (100 kHz offset) Output Transition Time Supply Current (Icc) 1. Divider will operate down to DC for square-wave input signal. 10 - 78 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz GaAs MMIC SUB-HARMONICALLY Input Sensitivity Window17 Temperature PUMPED MIXER vs. - 25 GHz Input Sensitivity Window, T= 25 C 20 15 INPUT POWER (dBm) INPUT POWER (dBm) 20 15 10 5 0 -5 -10 -15 -20 Min Pin +25 C Max Pin +25 C Min Pin -40 C Max Pin -40 C Min Pin +85 C Max Pin +85 C 10 5 0 -5 -10 -15 -20 0 1 2 3 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) Recommended Operating Window 10 7 8 9 10 0 1 2 3 4 5 6 INPUT FREQUENCY (GHz) Output Power vs. Temperature 0 SSB Phase Noise Performance, Pin= 0 dBm, T= 25 C 0 -20 OUTPUT POWER (dBm) -2 -40 -60 -80 -100 -120 -140 -160 2 10 -4 -6 +25 C -40 C +85 C -8 -10 0 1 2 3 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) 10 3 10 4 10 5 10 6 10 7 OFFSET FREQUENCY (Hz) Output Harmonic Content, Pin= 0 dBm, T= 25 C 0 Reverse Leakage, Pin= 0 dBm, T= 25 C 0 -10 POWER LEVEL (dBm) -10 OUTPUT LEVEL (dBm) -20 -30 -40 -50 -60 -20 -30 -40 Pfeedthru 2nd Harmonic 3rd Harmonic -50 0 1 2 3 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) 0 1 2 3 4 5 6 7 8 9 10 INPUT FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 10 - 79 FREQ. DIVIDERS & DETECTORS - SMT SSB PHASE NOISE (dBc/Hz) MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Output Voltage Waveform, Pin= 0 dBm, Fout= 882 MHz, T= 25 C 300 250 200 150 AMPLITUDE (mV) Absolute Maximum Ratings RF Input (Vcc= +3.0V) Vcc Maximum Channel Temperature Continuous Pdiss (T=85 C) (derate 5mW/C above 85 C) Storage Temperature Operating Temperature +15 dBm +3.5V 135 C 250mW -65 to +150 C -40 to +85 C 100 50 0 -50 -100 -150 -200 -250 -300 23 23.2 23.4 23.6 23.8 24 24.2 24.4 24.6 24.8 25 10 FREQ. DIVIDER & DETECTORS - SMT DC blocking capacitors are required at RF input and RF output ports. Choose value for lowest frequency of operation. TIME (nS) Typical Supply Current vs. Vcc Vcc (V) 2.70 3.0 3.30 Icc (mA) 42 53 63 Note: Divider will operate over full voltage range shown above Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. 10 - 80 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Pin Description Pin Number Function Description Interface Schematic 1, 4 N/C No Connection 2 GND Pin must connect ro RF/DC ground. 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 81 3 IN RF input must be DC blocked. 5 Vcc Supply voltage 3V 0.3V. 6 OUT Divided output must be DC blocked. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Evaluation PCB 10 FREQ. DIVIDER & DETECTORS - SMT Note: Line lengths on pins 1 & 4 (N/C) are not necessary. List of Materials Item J1 - J2 J3 - J4 C1 - C2 C3 C4 U1 PCB* Description PC Mount SMA RF Connector DC Pin 100 pF Capacitor, 0402 Pkg. 1000 pF Capacitor, 0402 Pkg. 10 F Tantalum Capacitor, 1206 Pkg. HMC433 Divide-by-4 105199 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. * Circuit Board Material: Rogers 4350 10 - 82 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v01.1002 HMC433 SMT GaAs HBT MMIC DIVIDE-BY-4, DC - 8.0 GHz Application Circuit 10 FREQ. DIVIDERS & DETECTORS - SMT 10 - 83 Note: DC blocking capacitor values (C1, C2) and DC decoupling capacitor values (C3, C4) are chosen for lowest frequency of operation. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com |
Price & Availability of HMC433
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |