 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| LM102 LM302 Voltage Followers November 1994 LM102 LM302 Voltage Followers General Description The LM102 series are high-gain operational amplifiers designed specifically for unity-gain voltage follower applications Built on a single silicon chip the devices incorporate advanced processing techniques to obtain very low input current and high input impedance Further the input transistors are operated at zero collector-base voltage to virtually eliminate high temperature leakage currents It can therefore be operated in a temperature stabilized component oven to get extremely low input currents and low offset voltage drift The LM102 which is designed to operate with supply voltages between g12V and g15V also features low input capacitance as well as excellent small signal and large signal frequency response all of which minimize high frequency gain error Because of the low wiring capacitances inherent in monolithic construction this fast operation can be realized without increasing power consumption Features Y Y Y Y Y Y Fast slewing 10V ms Low input current 10 nA (max) High input resistance 10 000 MX No external frequency compensation required Simple offset balancing with optional 1 kX potentiometer Plug-in replacement for both the LM101 and LM709 in voltage follower applications Schematic Diagram TL H 7753 - 1 C1995 National Semiconductor Corporation TL H 7753 RRD-B30M115 Printed in U S A Absolute Maximum Ratings If Military Aerospace specified devices are required please contact the National Semiconductor Sales Office Distributors for availability and specifications (Note 6) g18V Supply Voltage Power Dissipation (Note 1) Input Voltage (Note 2) Output Short Circuit Duration (Note 3) 500 mW g15V Operating Free Air Temperature Range b 55 C to a 125 LM102 LM302 0 C to a 70 b 65 C to a 150 Storage Temperature Range Lead Temperature (Soldering 10 sec ) 300 ESD rating to be determined C C C C Indefinite Electrical Characteristics (Note 4) Parameter Input Offset Voltage Input Bias Current Input Resistance Input Capacitance Large Signal Voltage Gain Output Resistance Supply Current Input Offset Voltage Offset Voltage Temperature Drift Input Bias Current Large Signal Voltage Gain Output Voltage Swing Supply Current Supply Voltage Rejection Ratio TA e TAMAX TA e TAMIN VS e g15V VOUT e g10V RL e 10 kX VS e g15V RL e 10 kX (Note 5) TA e 125 C g12V s VS s g15V Conditions Min TA e 25 C TA e 25 C TA e 25 C 1010 LM102 Typ 2 3 1012 30 Max 5 10 109 Min LM302 Type 5 10 1012 30 0 9985 25 55 75 0 9995 08 35 10 25 55 20 20 10 100 30 20 15 50 Max 15 30 Units mV nA X pF VV X mA mV mV C nA nA TA e 25 C VS g15V VOUT e g10V RL e 8 kX TA e 25 C TA e 25 C 0 999 0 9996 08 35 6 3 30 0 999 g10 g10 V mA 26 60 40 60 dB Note 1 The maximum junction temperature of the LM102 is 150 C while that of the LM302 is 85 C For operating at elevated temperatures devices in the H08 package must be derated based on a thermal resistance of 150 C W junction to ambient or 20 C W junction to case Note 2 For supply voltages less than g15V the absolute maximum input voltage is equal to the supply voltage Note 3 It is necessary to insert a resistor (at least 5k and preferably 10k) in series with the input pin when the amplifier is driven from low impedance sources to prevent damage when the output is shorted and to ensure stability Note 4 These specifications apply for g12V s VS s g15V and b 55 C s TA s 125 C for the LM102 and 0 C s TA s 70 C for the LM302 unless otherwise specified Note 5 Increased output swing under load can be obtained by connecting an external resistor between the booster and V Note 6 Refer to RETS102X for the LM102H military specifications b terminals See curve APPLICATION HINT The input must be driven from a source impedance of typically 10 kX (5 kX Min) to maintain stability The total source impedance will be reduced at high frequencies if there is stray capacitance at the input pin In these cases a 10 kX resistor should be inserted in series with the input physically close to the input pin to minimize the stray capacitance and prevent oscillation 2 Guaranteed Performance Characteristics LM102 Input Current Output Swing Supply Current TL H 7753 - 7 Typical Performance Characteristics LM102 Voltage Gain and Phase Lag Voltage Gain and Phase Lag Output Resistance Positive Output Swing Negative Output Swing Output Swing Large Signal Frequency Response Large Signal Pulse Response Maximum Power Dissipation TL H 7753 - 8 3 Guaranteed Performance Characteristics LM302 Input Current Output Swing Supply Current TL H 7753 - 9 Typical Performance Characteristics LM302 Voltage Gain and Phase Lag Voltage Gain and Phase Lag Output Resistance Positive Output Swing Negative Output Swing Output Swing Large Signal Frequency Response Large Signal Pulse Response Maximum Power Dissipation TL H 7753 - 10 4 Typical Applications Low Pass Active Filter Values are for 10 kHz cutoff Use silvered mica capacitors for good temperature stability TL H 7753 - 3 Sample and Hold with Offset Adjustment Polycarbonate-dielectric capacitor TL H 7753 - 4 High Pass Active Filter Values are for 100 Hz cutoff Use metalized polycarbonate capacitors for good temperature stability TL H 7753 - 5 High Input Impedance AC Amplifier TL H 7753 - 6 5 LM102 LM302 Voltage Followers Connection Diagram Metal Can Package Top View TL H 7753 - 2 Order Number LM102H 883 See NS Package Number H08C Physical Dimensions inches (millimeters) Metal Can Package (H) Order Number LM102H 883 NS Package Number H08C LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION As used herein 1 Life support devices or systems are devices or systems which (a) are intended for surgical implant into the body or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user National Semiconductor Corporation 1111 West Bardin Road Arlington TX 76017 Tel 1(800) 272-9959 Fax 1(800) 737-7018 2 A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor Europe Fax (a49) 0-180-530 85 86 Email cnjwge tevm2 nsc com Deutsch Tel (a49) 0-180-530 85 85 English Tel (a49) 0-180-532 78 32 Fran ais Tel (a49) 0-180-532 93 58 Italiano Tel (a49) 0-180-534 16 80 National Semiconductor Hong Kong Ltd 13th Floor Straight Block Ocean Centre 5 Canton Rd Tsimshatsui Kowloon Hong Kong Tel (852) 2737-1600 Fax (852) 2736-9960 National Semiconductor Japan Ltd Tel 81-043-299-2309 Fax 81-043-299-2408 National does not assume any responsibility for use of any circuitry described no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications |
Price & Availability of LM102
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |