 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| NJG1560PB1 Feb.28,2002 Ver.0 PDC Dual Band MIXER GaAs MMIC GENERAL DESCRIPTION The NJG1560PB1 is a mixer GaAs MMIC includes local amplifier targeted to dual band (800MHz, 1.5GHz) application. The band switching between 800MHz and 1500MHz is made by 1bit control signal by using inverter circuit included in this IC. The ultra small and thin FFP12-B1 is applied. PACKAGE OUTLINE NJG1560PB1 FEATURES Low voltage operation Low current consumption Low Inverter current High conversion gain High input IP3 Low noise figure Ultra small & thin package +2.8V typ. 5.9mA typ. 100uA typ. 11dB typ. @VCTL=0V, fRF1=820MHz 11dB typ. @VCTL=2.4V, fRF2=1489MHz @VCTL=0V, fRF1=820MHz +3dBm typ. +3dBm typ. @VCTL=2.4V, fRF2=1489MHz @VCTL=0V, fRF1=820MHz 5.5dB typ. 5.0dB typ. @VCTL=2.4V, fRF2=1489MHz FFP12-B1 (Package size: 2.0mmx2.0mmx0.85mm) PIN CONFIGURATION (Top View) 9 8 7 10 6 11 5 12 4 1 2 3 Pin Connection 1. GND 2. LOIN1 (800MHz) 3. VCTL 4. IFOUT 5. VLO1 (800MHz) 6. VLO2 (1.5GHz) 7. VINV 8. GND 9. LOIN2 (1.5GHz) 10. GND 11. RFIN2 (1.5GHz) 12. RFIN1 (800MHz) Note: The specifications and description listed in this catalog are subject to change without prior notice. -1- NJG1560PB1 ABSOLUTE MAXIMUM RATINGS (Ta=25C, Zs=Zl=50) PARAMETERS Operating voltage Control voltage Input power Power dissipation Operating temperature Storage temperature SYMBOL VDD VCTL Pin PD Topr Tstg CONDITIONS IFOUT, VLO 1, VLO2, VINV ports VCTL port RFIN1, RFIN2, LOIN1, LOIN2 ports RATINGS 5.0 VINV +10 300 -40~+85 -55~+125 UNITS V V dBm mW C C ELECTRICAL CHARACTERISTICS 1 (DC) GENERAL CONDITIONS: Ta=25C, VMIX=VLO1=VLO2=VINV=2.8V PARAMETERS Mixer supply voltage Local Amplifier supply voltage 1 Local Amplifier supply voltage 2 Inverter supply voltage Mixer current Local Amplifier current1 Local Amplifier current2 Inverter current Control voltage (LOW) Control voltage (HIGH) Control current SYMBOL VMIX VLO1 VLO2 VINV IMIX ILO1 ILO2 IINV VCTL(L) VCTL(H) ICTL CONDITIONS IFOUT port VLO1 ports VLO2 ports VINV port IFOUT port, PRF=PLO=OFF, VCTL=0V or 2.4V VLO1 port, PRF=PLO=OFF, VCTL=0V VLO2port, PRF=PLO=OFF, VCTL=2.4V VINV port VCTL port VCTL port VCTL port, VCTL=2.4V MIN 2.5 2.5 2.5 2.5 0 2.0 TYP 2.8 2.8 2.8 2.8 4.9 1.0 1.0 100 0 2.4 20 MAX 4.5 4.5 4.5 4.5 6.1 1.2 1.2 150 0.8 VINV 40 UNITS V V V V mA mA mA uA V V uA -2- NJG1560PB1 ELECTRICAL CHARACTERISTICS 2 (800MHz RF) GENERAL CONDITIONS: Ta=+25C, VMIX=VLO1=VINV=2.8V, VCTL=0V, fRF1=820MHz, PRF1=-30dBm, fLO1=689.95MHz, PLO1=-15dBm, fIF=130.05MHz, Zs=Zl=50, with application circuit PARAMETERS Operating frequency Conversion gain Noise figure Input 3rd order intercept point Pout at 1dB gain compression point RF IN1 port VSWR LOCAL IN1 port VSWR IF OUT port VSWR SYMBOL freq Gc NF IIP3 P-1dB(IN) VSWRRF VSWRLO VSWRIF SSB NF 2 tone offset frequency=100kHz CONDITIONS RFIN1 port MIN 810 10.0 0 -11.0 TYP 820 11.0 5.5 +3.0 -9.0 1.5 1.5 1.5 MAX 885 12.0 6.5 2.0 2.0 2.0 UNITS MHz dB dB dBm dBm ELECTRICAL CHARACTERISTICS 3 (1.5GHz RF) GENERAL CONDITIONS: Ta=+25C, VMIX=VLO2=VINV=2.8V, VCTL=2.4V, fRF2=1489MHz, PRF2=-30dBm, fLO2=1358.95MHz, PLO2=-15dBm, fIF=130.05MHz, Zs=Zl=50, with application circuit PARAMETERS Operating frequency Conversion gain Noise figure Input 3rd order intercept point Pout at 1dB gain compression point RF IN2 port VSWR LOCAL IN2 port VSWR IF OUT port VSWR SYMBOL freq Gc NF IIP3 P-1dB(IN) VSWRRF VSWRLO VSWRIF SSB NF 2 tone offset frequency=100kHz CONDITIONS RFIN2 port MIN 1477 10.0 0 -11.0 TYP 1489 11.0 5.0 +3.0 -9.0 1.5 1.5 1.5 MAX 1501 12.0 6.0 2.0 2.0 2.0 UNITS MHz dB dB dBm dBm -3- NJG1560PB1 TERMINAL INFORMATION Pin 1 2 3 4 5 6 7 8 9 10 11 12 Symbol GND LOIN1 VCTL IFOUT VLO1 VLO2 VINV GND LOIN2 GND RFIN2 RFIN1 Ground terminal(0V). Local power input terminal of 800MHz band local amplifier. External matching circuit is required. Description Control voltage input terminal. This terminal is set to 800MHz band or 1.5GHz band to select. IF signal output terminal for mixer external matching circuit is required. Please connect mixer power supply through choke inductor (L7) as shown in test circuit. 800MHz band local amplifier supply terminal. Please place L6 close to this terminal as shown in test circuit. 1.5GHz band local amplifier supply terminal. Please place L5 close to this terminal as shown in test circuit. Power supply terminal of the inverter circuit. Ground terminal(0V). Local power input terminal of 1.5GHz local amplifier. External matching circuit is required. Ground terminal(0V). RF input terminal of 1.5GHz band mixer. External matching circuit is required. RF input terminal of 800MHz band mixer. External matching circuit is required. NOTE: 1) Ground terminal (1, 8, 10pin) should be connected to ground plane by multiple via holes for good grounding. -4- NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) Gc , NF vs. RF Frequency 13 12 12 14 11 Gc, NF vs. LO Power 14 Gc 12 Gc 12 Conversion Gain (dB) Noise Figure (dB) 10 9 8 7 6 5 800 9 8 10 10 8 8 NF 7 6 5 4 900 6 6 4 NF 4 820 840 860 880 2 -40 2 -30 -20 -10 0 10 RF Frequency (MHz) Condition fIF=130.05MHz fRF=800~900MHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V LO Power (dBm) Condition fIF=130.05MHz fRF=820MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V OIP3 , IIP3 vs. RF Frequency 16 15 14 8 16 OIP3, IIP3 vs. LO Power 10 7 6 OIP3 14 OIP3 8 OIP3 (dBm) 12 11 10 9 8 800 4 3 IIP3 (dBm) 10 4 IIP3 8 2 2 1 0 900 6 IIP3 0 820 840 860 880 4 -40 -2 -30 -20 -10 0 10 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V -5- IIP3 (dBm) 13 5 OIP3 (dBm) 12 6 Noise Figure (dB) 11 10 Conversion Gain (dB) NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) IF Output Power vs. RF Power 5 0 20 IF, IM3 vs. RF Power IF Output Power (dBm) 0 IF , IM3 (dBm) -5 -10 -15 -20 -25 P-1dB(IN)=-7.8dBm IF -20 -40 -60 -80 IM3 -30 -40 -30 -20 -10 0 10 -100 -40 -30 -20 -10 0 10 RF Power (dBm) Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V RF Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V LOCAL Leak Level vs. LO Frequency -12 -14 LOCAL Leak Level (dBm) Plk-IF -16 -18 -20 -22 Plk-RF -24 -26 -28 660 680 700 720 740 760 780 LO Frequency (MHz) -6- NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) Gc, NF vs. Ambient Temperature 14 14 OIP3, IIP3 vs. Ambient Temperature 18 16 14 Conversion Gain (dB) 12 10 8 6 4 2 0 -40 Gc 12 OIP3 fRF=810MHz fRF=820MHz fRF=885MHz 12 10 8 6 4 OIP3 (dBm) 10 Noise Figure (dB) 14 12 10 8 6 4 -40 NF 8 6 fRF=810MHz fRF=820MHz fRF=885MHz 4 2 0 IIP3 2 0 -20 0 20 40 o 60 80 -20 0 20 40 o 60 80 Ambient Temperature ( C) Condition fIF=130.05MHz fRF=810~885MHz, PRF=-30dBm fLO=679.95~754.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V Ambient Temperature ( C) Condition fIF=130.05MHz fRF1=810~885MHz, fRF2=fRF1+100kHz, PRF=-30dBm fLO==679.95~754.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V P-1dB(IN) vs. Ambient Temperature -4 -6 P-1dB(IN) (dBm) -8 -10 fRF=820MHz -12 -14 -16 -50 0 50 o 100 Ambient Temperature ( C) Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V -7- IIP3 (dBm) NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) Conversion Gain vs. Frequency 14 10 8 Noise Figure vs. Frequency Conversion Gain (dB) 12 Noise Figure (dB) 6 4 -40 C o o 10 8 -40 C -25 C 0C o o o 2 0 -2 800 -25 C 0C 25 C 50 C 80 C o o o o 6 25 C 50 C 80 C o o o 4 800 820 840 860 880 900 820 840 860 880 900 RF Frequency (MHz) Condition fIF=130.05MHz fRF=800~900MHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V RF Frequency (MHz) Condition fIF=130.05MHz fRF=800~900MHz fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V OIP3 vs. Frequency 18 16 14 10 8 6 IIP3 vs. Frequency OIP3 (dBm) 12 10 8 6 4 800 -40 C -25 C 0C 25 C 50 C 80 C o o o o o o IIP3 (dBm) 4 2 -40 C o o 0 -2 -4 800 -25 C 0C 25 C 50 C 80 C o o o o 820 840 860 880 900 820 840 860 880 900 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V RF Frequency (MHz) Condition fIF=130.05MHz fRF1=800~900MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=669.95~769.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=0V -8- NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) Conversion Gain vs. LO Power 14 12 14 Noise Figure vs. LO Power -40 C o o Conversion Gain (dB) 12 -25 C 0C 25 C o o o o Noise Figure (dB) 10 8 6 4 2 -40 o 10 8 6 4 2 -40 50 C 80 C -40 C -25 C 0C 25 C 50 C 80 C o o o o o -30 -20 -10 0 10 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=820MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V LO Power (dBm) Condition fIF=130.05MHz fRF=820MHz fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V OIP3 vs. LO Power 16 14 12 10 -40 C o o IIP3 vs. LO Power 10 -40 C o o 8 6 4 2 0 -2 -40 -25 C 0C 25 C o o o o OIP3 (dBm) IIP3 (dBm) 50 C 80 C 8 6 4 -40 -25 C 0C 25 C 50 C 80 C o o o o -30 -20 -10 0 10 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V LO Power (dBm) Condition fIF=130.05MHz fRF=820.0+820.1MHz, PRF=-30dBm fLO=689.95MHz VMIX=VLO=VINV=2.8V VCTL=0V -9- NJG1560PB1 TYPICAL CHARACTERISTICS (800MHz Band) RF IN1 Port Impedance (LOCAL IN1 Port, IF OUT Port: 50 term.) LOCAL IN1 Port Impedance (RF IN1 Port, IF OUT Port: 50 term.) IF OUT Port Impedance (RF IN1 Port, LOCAL IN1 Port: 50 term.) - 10 - NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) Gc , NF vs. RF Frequency 12 11 11 14 12 Gc , NF vs. LO Power 18 Gc Gc 10 16 Conversion Gain (dB) Conversion Gain (dB) 10 9 8 9 8 7 Noise Figure (dB) 8 6 4 2 0 -2 -40 12 10 8 6 NF 7 6 6 5 NF -30 -20 -10 0 10 4 2 5 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) Condition fIF=130.05MHz fRF=1470~1510MHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V LO Power (dBm) Condition fIF=130.05MHz fRF=1489MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 , IIP3 vs. RF Frequency 18 16 14 14 12 18 16 14 OIP3 , IIP3 vs. LO Power 14 OIP3 12 10 8 6 4 2 OIP3 10 OIP3 (dBm) OIP3 (dBm) IIP3 (dBm) 12 10 8 6 4 2 -40 12 10 8 6 8 6 IIP3 4 2 IIP3 0 -2 4 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 -30 -20 -10 0 10 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V - 11 - IIP3 (dBm) Noise Figure (dB) 10 14 NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) IF Output Power vs. RF Power 5 0 20 0 IF , IM3 vs. RF Power IF Output Power (dBm) IF , IM3 (dBm) -5 -10 -15 -20 -25 P-1dB(IN)=-8.2dBm IF -20 -40 -60 -80 IM3 -30 -40 -30 -20 -10 0 10 -100 -40 -30 -20 -10 0 10 RF Power (dBm) Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V RF Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V LOCAL Leak Level vs. LO Frequency -15 LOCAL Leak Level (dBm) -20 Plk-RF -25 -30 Plk-IF -35 -40 1340 1345 1350 1355 1360 1365 1370 1375 1380 LO Frequency (MHz) - 12 - NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) Gc, NF vs. Ambient Temperature 14 14 12 10 8 OIP3, IIP3 vs. Ambient Temperature 18 16 14 Gc OIP3 Conversion Gain (dB) 12 12 10 8 Noise Figure (dB) OIP3 (dBm) 10 8 14 12 NF 6 4 fRF=1477MHz IIP3 10 8 fRF=1477MHz 6 4 fRF=1489MHz fRF=1501MHz 6 4 fRF=1489MHz fRF=1501MHz 2 0 -40 2 0 6 4 -40 2 0 -20 0 20 40 o 60 80 -20 0 20 40 o 60 80 Ambient Temperature ( C) Condition fIF=130.05MHz fRF=1477~1501MHz, PRF=-30dBm fLO=1346.95~1470.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V Ambient Temperature ( C) Condition fIF=130.05MHz fRF1=1477~1501MHz, fRF2=fRF1+100kHz, PRF=-30dBm fLO=1346.95~1470.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V P-1dB(IN) vs. Ambient Temperature -4 -6 P-1dB(IN) (dBm) -8 -10 -12 fRF=1489MHz -14 -16 -40 -20 0 20 40 o 60 80 Ambient Temperature ( C) Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V - 13 - IIP3 (dBm) NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) Conversion Gain vs. Frequency 14 12 10 Noise Figure vs. Frequency -40 C -25 C 0C o o o Conversion Gain (dB) 12 Noise Figure (dB) 8 6 4 2 25 C 50 C 80 C o o o 10 8 -40 C -25 C 0C o o o 6 25 C 50 C 80 C o o o 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) Condition fIF=130.05MHz fRF=1470~1510MHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V RF Frequency (MHz) Condition fIF=130.05MHz fRF=1470~1510MHz fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 vs. Frequency 18 16 14 14 12 10 IIP3 vs. Frequency o o -40 C -25 C 0C 25 C 50 C o o o o OIP3 (dBm) IIP3 (dBm) 12 10 8 6 4 1470 1475 1480 1485 1490 1495 1500 1505 1510 -40 C -25 C 0C 25 C 50 C 80 C o o o o o o 8 6 4 2 80 C 0 1470 1475 1480 1485 1490 1495 1500 1505 1510 RF Frequency (MHz) Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V RF Frequency (MHz) Condition fIF=130.05MHz fRF1=1470~1510MHz fRF2=fRF1+100kHz, PRF=-30dBm fLO=1339.95~1379.95MHz, PLO=-15dBm VMIX=VLO=VINV=2.8V VCTL=2.4V - 14 - NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) Conversion Gain vs. LO Power 14 12 18 16 Noise Figure vs. LO Power Conversion Gain (dB) -40 C o o Noise Figure (dB) 10 8 6 4 2 0 -2 -40 -40 C -25 C 0C 25 C 50 C 80 C o o o o o o 14 12 10 8 6 4 2 -40 -25 C 0C 25 C 50 C 80 C o o o o -30 -20 -10 0 10 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=1489MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V LO Power (dBm) Condition fIF=130.05MHz fRF=1489MHz fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V OIP3 vs. LO Power 18 16 14 14 12 10 IIP3 vs. LO Power -40 C -25 C 0C 25 C 50 C o o o o o o OIP3 (dBm) 12 10 8 6 4 2 -40 o IIP3 (dBm) 8 6 4 2 0 -2 -40 80 C -40 C -25 C 0C 25 C 50 C 80 C o o o o o -30 -20 -10 0 10 -30 -20 -10 0 10 LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V LO Power (dBm) Condition fIF=130.05MHz fRF=1489.0+1489.1MHz, PRF=-30dBm fLO=1358.95MHz VMIX=VLO=VINV=2.8V VCTL=2.4V - 15 - NJG1560PB1 TYPICAL CHARACTERISTICS (1.5GHz Band) RF IN2 Port Impedance (LOCAL IN2 Port, IF OUT Port: 50 term.) LOCAL IN2 Port Impedance (RF IN2 Port, IF OUT Port: 50 term.) IF OUT Port Impedance (RF IN2 Port, LOCAL IN2 Port: 50 term.) - 16 - NJG1560PB1 APPLICATION CIRCUIT (Top View) LOCAL IN2 (1.5GHz) L4 15nH VLO=2.8V 9 8 7 L5 12nH L3 RF IN2 2.2nH (1.5GHz) L1 33nH RF IN1 (800MHz) R1 3.9k L2 6.8nH 10 11 12 6 L6 39nH 5 4 L7 180nH 1 2 3 L8 47nH C4 0.01uF VMIX=2.8V LOCAL IN1 (800MHz) VCTL=0 or 2.4V VCTL=0V :800MHz ON VCTL=2.4V :1.5GHz ON C3 9pF C2 18pF IF OUT C1 0.01uF VINV=2.8V Parts list PARTS ID L1 L2 L3 L4 L5 L6 L7 L8 C1 C2 C3 C4 R1 COMMENT TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1005, 1005size) TAIYO-YUDEN (HK1608, 1608size) TAIYO-YUDEN (HK1005, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) MURATA (GRM36, 1005size) 1005 Size - 17 - NJG1560PB1 RECOMMENDED PCB DESIGN (Top View) LOCAL IN2 (1.5GHz) VINV RF IN2 (1.5GHz) VLO L4 L3 L5 L2 R1 L1 C3 L7 L8 C4 C2 L6 C1 IF OUT VMIX RF IN1 (800MHz) VCTL LOCAL IN1 1pin INDEX PCB(FR-4), t=0.2mm MICROSTRIP LINE WIDTH=0.4mm (Zo=50) PCB SIZE=33.6x26.6mm PRECAUTIONS 1. Please locate L6 close to VLO1 terminal (5). 2. Please locate L5 close to VLO2 terminal (6). 3. Please locate C1 close to L5 and L6. 4. Please locate C4 close to L7. - 18 - NJG1560PB1 MEASURING BLOCK DIAGRAM VCTL= 0 or 2.4V LOCAL IN1 or 2 SG (LOCAL) D.U.T. PCB VMIX= VLO= VINV =2.8V VCTL= 0 or 2.4V LOCAL IN1 or 2 VMIX= VLO= VINV =2.8V IF OUT Spectrum Analyzer SG (LOCAL) IF OUT D.U.T. PCB NF Meter BPF RF IN1 or 2 SG (RF) BPF RF IN1 or 2 6dB ATT Noise Source BPF Conversion Gain Measuring Block Diagram Noise Figure Measuring Block Diagram VCTL= 0 or 2.4V LOCAL IN1 or 2 SG (LOCAL) D.U.T. PCB VMIX= VLO= VINV =2.8V IF OUT Spectrum Analyzer RF IN1 or 2 SG (RF1) Power Comb. ATT SG (RF2) OIP3, IIP3 Measuring Block Diagram - 19 - NJG1560PB1 PACKAGE OUTLINE (FFP12-B1) 1pin INDEX 12pin (TOP VIEW) 1pin 0.35 2pin INDEX 0. 35 0.2540.1 0.850.15 0.103 0.303 0.17 0.30 (SIDE VIEW) 2.00.1 0.50 0.20 (BOTTOM VIEW) 0.365 2.00.1 0.27 UNIT PCB OVER COAT TERMINAL TREAT WEIGHT : mm : Ceramic : Epoxy resin : Au : 10mg Cautions on using this product This product contains Gallium-Arsenide (GaAs) which is a harmful material. * Do NOT eat or put into mouth. * Do NOT dispose in fire or break up this product. * Do NOT chemically make gas or powder with this product. * To waste this product, please obey the relating law of your country. This product may be damaged with electric static discharge (ESD) or spike voltage. Please handle with care to avoid these damages. [CAUTION] The specifications on this databook are only given for information , without any guarantee as regards either mistakes or omissions. The application circuits in this databook are described only to show representative usages of the product and not intended for the guarantee or permission of any right including the industrial rights. - 20 - |
Price & Availability of NJG1560PB1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |