View MC100E214_289782.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
8 Bit Scannable Register
The MC10E/100E241 is an 8-bit shiftable register. Unlike a standard universal shift register such as the E141, the E241 features internal data feedback organized so that the SHIFT control overrides the HOLD/LOAD control. This enables the normal operations of HOLD and LOAD to be toggled with a single control line without the need for external gating. It also enables switching to scan mode with the single SHIFT control line. The eight inputs D0 - D7 accept parallel input data, while S-IN accepts serial input data when in shift mode. Data is accepted a set-up time before the positive-going edge of CLK; shifting is also accomplished on the positive clock edge. A HIGH on the Master Reset pin (MR) asynchronously resets all the registers to zero.
MC10E241 MC100E241
8-BIT SCANNABLE REGISTER
* * * * * *
SHIFT overrides HOLD/LOAD Control 1000ps Max. CLK to Q Asynchronous Master Reset Pin-Compatible with E141 Extended 100E VEE Range of - 4.2V to - 5.46V 75k Input Pulldown Resistors
FN SUFFIX PLASTIC PACKAGE CASE 776-02
Pinout: 28-Lead PLCC (Top View)
SEL0 25 SEL1 CLK MR VEE S-IN D0 D1 26 27 28 1 2 3 4 5 D2 6 D3 7 D4 8 VCCO 9 Q0 10 Q1 11 Q2 D1 - D6 BITS 1-6 NC 24 D7 23 D6 22 D5 21 VCCO 20 Q7 19 18 17 16 15 14 13 12 Q6 Q5 VCC NC VCCO Q4 Q3 D0 S-IN
LOGIC DIAGRAM
DQ R
Q0
DQ R
Q1 - Q6
* All VCC and VCCO pins are tied together on the die.
PIN NAMES
Pin D0 - D7 S-IN SEL0 SEL1 CLK MR Q0 - Q7 Function Parallel Date Inputs Serial Data Inputs SHIFT Control HOLD/LOAD Control Clock Master Reset Data Outputs DQ D7 HOLD/LOAD SHIFT CLK MR R Q7
7/96
(c) Motorola, Inc. 1996
2-1
REV 3
MC10E241 MC100E241
DC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol IIH IEE Characteristic Input HIGH Current Power Supply Current 10E 100E 125 125 min typ max 150 150 150 125 125 min 25C typ max 150 150 150 125 144 min 85C typ max 150 150 173 Unit A MA Condition
AC CHARACTERISTICS (VEE = VEE(min) to VEE(max); VCC = VCCO = GND)
0C Symbol fSHIFT tPLH tPHL ts Characteristic Max. Shift Frequency Propagation Delay to Output Clk MR Setup Time D SEL0 (SHIFT) SEL1 (HOLD/LOAD) S-IN Hold Time D SEL0 (SHIFT) SEL1 (HOLD/LOAD) S-IN Reset Recovery Time Minimum Pulse Width Clk, MR Within-Device Skew Rise/Fall Times 20 - 80% 300 min 700 625 600 175 350 400 125 200 100 50 300 900 400 60 525 800 300 typ 900 750 725 25 200 250 -100 - 25 - 200 - 250 100 600 975 975 max min 700 625 600 175 350 400 125 200 100 50 300 900 400 60 525 800 300 25C typ 900 750 725 25 200 250 -100 - 25 - 200 - 250 100 600 975 975 max min 700 625 600 175 350 400 125 200 100 50 300 900 400 60 525 800 ps ps 1 85C typ 900 750 725 25 200 250 -100 ps - 25 - 200 - 250 100 600 ps ps 975 975 ps max Unit MHz ps Condition
th
tRR tPW tSKEW tr tf
1. Within-device skew is defined as identical transitions on similar paths through a device.
FUNCTION TABLE
MR 1 0 0 0 SEL0 X 1 0 0 SEL1 X X 1 0 Function Outputs LOW Shift Data Hold Data Load Data
MOTOROLA
2-2
ECLinPS and ECLinPS Lite DL140 -- Rev 4
MC10E241 MC100E241
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
0.007 (0.180) U T L -M
M
B -NY BRK
M
S
N
S S
0.007 (0.180)
T L -M
N
S
D Z -L-M-
W
28 1
D X VIEW D-D G1 0.010 (0.250)
S
V
T L -M
S
N
S
A Z R
0.007 (0.180) 0.007 (0.180)
M
T L -M T L -M
S
N N
S
H
S
0.007 (0.180)
M
T L -M
S
N
S
M
S
C
E G G1 0.010 (0.250)
S
K1 0.004 (0.100) J -TSEATING PLANE
K F VIEW S 0.007 (0.180)
M
VIEW S T L -M
S
T L -M
S
N
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIM G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIM R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 -- 0.025 -- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 -- 0.020 2 10 0.410 0.430 0.040 --
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 -- 0.64 -- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 -- 0.50 2 10 10.42 10.92 1.02 --
ECLinPS and ECLinPS Lite DL140 -- Rev 4
2-3
MOTOROLA
MC10E241 MC100E241
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-4
*MC10E241/D*
MC10E241/D ECLinPS and ECLinPS Lite DL140 -- Rev 4

▲Up To Search▲

Price & Availability of MC100E214

	To Download MC100E214 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .