 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SLIM POLARIZED RELAY TN-RELAYS * Surge voltage withstand: 1500 V FCC Part 68 * Sealed construction allows automatic cleaning * Self-clinching terminal also available 14 .551 5.6 .220 9.8 .386 FEATURES * Small size for minimal PC board mounting requirements * Small header area makes higher density mounting possible * High sensitivity: 140 mW nominal operating power (single side stable 3-12 V type) mm inch SPECIFICATIONS Contact Arrangement Initial contact resistance, max. (By voltage drop 6 V DC 1A) Contact material Nominal switching capacity (resistive load) Max. switching power (resistive load) Rating Max. switching voltage Max. switching current Min. switching capacity f1 Single side stable Nominal operating power 1 coil latching 2 coil latching Mechanical (at 180 cpm) 1 A 30 V DC resistive load Electrical (at 20 cpm) 0.5 A 125 V AC resistive load 2 Form C 60 m Gold-clad silver 1 A 30 V DC, 0.5 A 125 V AC 30 W, 62.5 VA 110 V DC,125 V AC 1A 10 A 10 mV DC 140 mW (3 to 12 V DC) 200 mW (24 V DC) 300 mW (48 V DC) 100 mW (3 to 12 V DC) 150 mW (24 V DC) 200 mW (3 to 12 V DC) 300 mW (24 V DC) 108 2 x 105 105 Characteristics Initial insulation resistance*1 Between open contacts Initial Between contact and breakdown coil voltage Between contact sets FCC surge voltage between open contacts Temperature rise*2 (at 20C) Operate time [Set time]*3 (at 20C) Release time [Reset time]*4 (at 20C) Functional*5 Shock resistance Destructive*6 Functional*7 Vibration resistance Destructive Conditions for operation, transport and storage*8 (Not freezing and condensing at low temperature) Unit weight Ambient temperature Humidity Max. 3 [Max. 3 Max. 3 [Max. 3 Min. 1,000 M (at 500 V DC) 750 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,000 Vrms for 1 min. (Detection current: 10 mA) 1,500 V Max. 50C ms (Approx. 2 ms (Approx. 2 ms (Approx. 1 ms (Approx. 2 ms) ms)] ms) ms)] Expected life (min. operations) Note: Min. 490 m/s2 {50G} Min. 980 m/s2 {100G} 176.4 m/s2 {18G}, 10 to 55 Hz at double amplitude of 3 mm 294 m/s2 {30G}, 10 to 55 Hz at double amplitude of 5 mm -40C to +70C -40F to +158F 5 to 85% R.H. Approx. 1.5 g .053 oz f1This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the actual load. Remarks * Specifications will vary with foreign standards certification ratings. *1 Measurement at same location as "Initial breakdown voltage" section. *2 By resistive method, nominal voltage applied to the coil; contact carrying current: 1 A. *3 Nominal voltage applied to the coil, excluding contact bounce time. 4 Nominal voltage applied to the coil, excluding contact bounce time without diode. * *5 Half-wave pulse of sine wave: 11 ms; detection time: 10 s. *6 Half-wave pulse of sine wave: 6 ms. *7 Detection time: 10 s. *8 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions for use (Page 178). ORDERING INFORMATION Ex. TN 2 L2 H 12V Contact arrangement 2: 2 Form C Operating function Nil: Single side stable L: 1 coil latching L2: 2 coil latching Terminal shape Nil: Standard PC board terminal H: Self-clinching terminal Coil voltage(DC) 3,4.5,5,6,9,12, 24,48*V *48 V coil type: Single side stable only Note: AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "-3" like TN2-12V-3. 150 TN TYPES AND COIL DATA (at 20C 68F) 1. Single side stable Part No. Standard PC board terminal TN2-3 V TN2-4.5 V TN2-5 V TN2-6 V TN2-9 V TN2-12 V TN2-24 V TN2-48 V Self-clinching terminal TN2-H-3 V TN2-H-4.5 V TN2-H-5 V TN2-H-6 V TN2-H-9 V TN2-H-12 V TN2-H-24 V TN2-H-48 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 48 Pick-up voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 36 Drop-out voltage, V DC (min.) 0.3 0.45 0.5 0.6 0.9 1.2 2.4 4.8 Nominal operating current, mA (10%) 46.7 31.1 28.1 23.3 15.5 11.7 8.3 6.25 Coil resistance, (10%) 64.3 145 178 257 579 1,028 2,880 7,680 Nominal operating power, mW 140 140 140 140 140 140 200 300 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 36 57.6 2. 1 Coil latching Part No. Standard PC board terminal TN2-L-3 V TN2-L-4.5 V TN2-L-5 V TN2-L-6 V TN2-L-9 V TN2-L-12 V TN2-L-24 V Self-clinching terminal TN2-L-H-3 V TN2-L-H-4.5 V TN2-L-H-5 V TN2-L-H-6 V TN2-L-H-9 V TN2-L-H-12 V TN2-L-H-24 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 Set voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Reset voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Nominal operating current, mA (10%) 33.3 22.2 20 16.7 11.1 8.3 6.3 Coil resistance, (10%) 90 202.5 250 360 810 1,440 3,840 Nominal operating power, mW 100 100 100 100 100 100 150 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 36 3. 2 Coil latching Part No. Standard PC board terminal TN2-L2-3 V TN2-L2-4.5 V TN2-L2-5 V TN2-L2-6 V TN2-L2-9 V TN2-L2-12 V TN2-L2-24 V Notes: 1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse. 2. Standard packing: Tube: 50 pcs.; Case: 1,000 pcs. 3. In case of 5 V drive circuit, it is recommended to use 4.5 V type relay. 4. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "-3" like TN2-12V-3. Self-clinching terminal TN2-L2-H-3 V TN2-L2-H-4.5 V TN2-L2-H-5 V TN2-L2-H-6 V TN2-L2-H-9 V TN2-L2-H-12 V TN2-L2-H-24 V Nominal voltage, V DC 3 4.5 5 6 9 12 24 Set voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Reset voltage, V DC (max.) 2.25 3.38 3.75 4.5 6.75 9 18 Nominal operating current, mA (10%) 66.7 44.4 40 33.3 22.2 16.7 12.5 Coil resistance, (10%) 45 101.2 125 180 405 720 1,920 Nominal operating power, mW 200 200 200 200 200 200 300 Max. allowable voltage, V DC 4.5 6.7 7.5 9 13.5 18 28.8 DIMENSIONS Standard PC board terminal 14 551 9.5 9.8.374 .386 3.5 .138 2.54 .100 0.5 .020 1.385 .055 0.25 .010 2.54 .100 5.6 .220 mm inch PC board pattern (Copper-side view) 10.16 .400 2.54 .100 2.54 .100 10-1.0 dia. hole 10-.039 dia. hole Tolerance: 0.1 .004 Self-clinching terminal 14 551 9.5 9.8.374 .386 3.5 .138 2.54 .100 0.5 .020 1.385 .055 0.25 .010 2.54 .100 5.6 .220 Schematic (Bottom view) * Single side stable * 1-coil latching (Deenergized condition) (Reset condition) 12345 12345 * 2-coil latching (Reset condition) 12345 10 9 8 7 6 Direction indication* 10 9 8 7 6 Direction indication* 10 9 8 7 6 Direction indication* General tolerance: 0.3 .012 *Orientation stripe located on top of relay 151 TN REFERENCE DATA 1. Maximum switching capacity 2. Life curve 3. Mechanical life Tested sample: TN2-12V, 10 pcs. Ratio against the rated voltage, %V 100 90 80 70 60 50 40 30 20 10 30 100 Switching voltage,V 200 0 1.0 0.5 Switching current, A 0 10 100 1,000 No. of operations, x104 Drop-out voltage Max. Min. Pick-up voltage Max. Min. 1.0 0.5 0.4 0.3 0.2 No. of operations, x104 Switching current, A DC load (cos=1) AC load (cos=1) 30 V DC resistive load 100 125 V AC resistive load 10 10,000 4. Electrical life (DC load) Tested sample: TN2-12V, 10 pcs. Condition: 1 A 30 V DC resistive load, 20 cpm 5. Coil temperature rise Tested sample: TN2-12V Point measured: Inside the coil Ambient temperature: Room temperature (25 to 26C), 70C (77 to 79F), 158F 70 60 Temperature rise, C 50 40 30 20 10 0 Carrying current 0 A (Room temp.) 1 A (Room temp.) 0 A (70C) 1 A (70C) Change of pick-up and drop-out voltage Ratio against the rated voltage %V 100 90 80 70 60 50 40 30 20 10 0 5 10 15 No. of operations, x104 20 Min. Drop-out voltage Max. Change of contact resistance 100 90 Contact resistance,m Pick-up voltage 80 70 60 50 40 30 20 10 0 5 10 15 No.of operations, x104 20 Terminal No.2-3-4 Terminal No.7-8-9 Max. Min. 80 90 100 110 120 130 140 150 Coil applied voltage, %V 6. Operate/release time characteristics Tested sample: TN2-12V, 5 pcs. 6 Operate and release time, ms 7. Set/reset time characteristics Tested sample: TN2-L2-12V, 5 pcs. 6 Set time Set and reset time, ms Reset time 8. Distribution of pick-up and drop-out voltages Tested sample: TN2-12V, 40 pcs. 30 5 5 Pick-up voltage Quantity 20 4 4 Drop-out voltage 3 Operate time Max. Min. Max. Min. 3 2 2 Max. Min. 10 1 Release time 0 80 1 0 90 100 110 120 Coil applied voltage, %V 80 90 100 110 120 Coil applied voltage, %V 0 10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V 9. Distribution of set and reset voltage Tested sample: TN2-L2-12V, 32 pcs. 30 10. Ambient temperature characteristics Tested sample: TN2-12V, 5 pcs. x Variation ratio, % 40 30 Drop-out voltage 11. Distribution of contact resistance Tested sample: TN2-12V, 38 pcs. (38x4 contacts) 40 12345 ,,,, ,, ,, ,,, , ,, ,, , , Set voltage Reset voltage 30 20 Quantity x Quantity 20 Terminal No. 7,8,9 Side 6 7 8 9 10 Terminal No. 2,3,4 side 10 Pick-up voltage -40 -20 -10 0 Ambient 20 40 60 80 temperature, C -10 -20 -30 -40 20 10 10 0 10 20 30 40 50 60 70 80 90 100 Ratio against the rated voltage, %V 0 30 40 50 Contact resistance,m 152 TN 12-(1). Malfunctional shock (single side stable) Tested sample: TN2-12V, 6 pcs. , Z Z 12-(2). Malfunctional shock (latching) Tested sample: TN2-L2-12V, 6 pcs. , Z Z Y Y, Y X X , Y 980m/s2 Deenergized condition Energized condition Y, X X , 980m/s2 Y Deenergized condition Energized condition X 980m/s2 Z 980m/s2 X 980m/s2 Z 980m/s2 , Z 980m/s2 980m/s2 , Y , X 980m/s2 , Z 980m/s2 980m/s2 , Y , X 980m/s2 13-(1). Influence of adjacent mounting Rate of change, % 10 Pick-up voltage 0 -10 ON 13-(2). Influence of adjacent mounting Rate of change, % 10 Pick-up voltage 0 -10 ON ON ON ON ON Rate of change, % OFF OFF Rate of change, % OFF OFF 10 Drop-out voltage 0 -10 0 5 .197 Inter-relay distance OFF 20 Drop-out voltage 10 0 0 5 .197 Inter-relay distance OFF , mm inch , mm inch 14. Actual load test (35 mA 48 V DC wire spring relay load) Change of pick-up and drop-out voltage 100 Ratio against the rated voltage, %V 90 Contact resistance, m 80 70 60 50 40 30 20 10 0 10 20 30 40 No. of operations,x104 50 Drop-out voltage Max. Min. Pick-up voltage Max. Min. Change of contact resistance 100 90 80 70 60 50 40 30 20 10 0 10 20 30 40 No. of operations, x104 50 Terminal No. 2-3 Max. Min. Circuit 500 48 V DC 0.1 F 0.1 F 500 3 2 Wire spring relay Circuit diagram 15-(1). High-frequency characteristics Tested sample: TN2-xxV Isolation characteristics 15-(2). High-frequency characteristics Tested sample: TN2-xxV Insertion loss characteristics 1.6 15-(3). High-frequency characteristics Tested sample: TN2-xxV V.S.W.R. 2.2 2.1 2.0 V.S.W.R. 1.9 1.8 1.7 1.6 1.5 1.4 1.3 Insertion loss, dB 1.4 1.2 1.0 Terminal No. 2-3-4 0.8 0.6 Isolation, dB 100 Terminal No. 7-8-9 50 Terminal No. 2-3-4 Terminal No. 2-3-4 Terminal No. 7-8-9 0.4 Terminal No. 7-8-9 0.2 1.2 1.1 1.0 10 100 Frequency, MHz 1000 10 100 Frequency, MHz 1000 10 100 Frequency, MHz 1000 For Cautions for Use, see Page 178 and 179. 9/1/2000 All Rights Reserved, (c) Copyright Matsushita Electric Works, 153 Ltd. Go To Online Catalog |
Price & Availability of TN2-L2-H-9
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |