View MP7616_344126.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MP7616
15 V CMOS 16-Bit Multiplying Digital-to-Analog Converter
FEATURES
* * * * * Monolithic CMOS Construction Full Four-Quadrant Multiplication Excellent Stability Over Temperature and Time TTL/5 V CMOS Compatible Guaranteed Monotonic * * * * Low Sensitivity to Output Amplifier Vos Low Glitch Energy Buffered Version: MP7626 5 V Version: MP7616B
GENERAL DESCRIPTION
The MP7616 is a high density 16-bit CMOS multiplying Digital-to-Analog Converter. Silicon nitride passivation and untrimmed silicon chromium resistors have been combined to provide long term stability and reliability. Using the most significant bit (MSB) segmentation technique, the MP7616 features 13-bit (0.012%) differential and 12-bit (0.01%) integral linearity. To achieve 13-bit linearity without laser trim, the MP7616 digitally decodes the four MSB's into 15 equal current sources,
rather than the standard binary-weighted sources. Each resistor contributes only 1/16 full scale output thus reducing the matching accuracy requirement of the resistor and CMOS switches from 0.0015% to 0.024%. The decoding technique achieves an eightfold improvement in differential linearity stability over temperature, an eightfold improvement in relative accuracy due to aging effects (long term stability), a fourfold improvement in glitch amplitude, and a tenfold reduction in sensitivity to output amplifier offset voltage.
SIMPLIFIED BLOCK DIAGRAM
VDD
VREF R R R R R R R R R R R R R R R 12-Bit DAC IOUT2 IOUT1 To Switches To 12-Bit DAC RFB
4 to 15 Decoder
1 MSB
4
5
16 LSB
GND
Rev. 2.00 1
MP7616
ORDERING INFORMATION
Package Type
Plastic Dip Plastic Dip SOIC SOIC Ceramic Dip Ceramic Dip Ceramic Dip
Temperature Range
-40 to +85C -40 to +85C -40 to +85C -40 to +85C -40 to +85C -40 to +85C -55 to +125C
Part No.
MP7616JN MP7616KN MP7616JS MP7616KS MP7616JD MP7616KD MP7616TD*
INL (LSB)
+14 +7 +14 +7 +14 +7 +7
DNL (LSB)
+16 +8 +16 +8 +16 +8 +8
Gain Error (% FSR)
+0.8 +0.8 +0.8 +0.8 +0.8 +0.8 +0.8
*Contact factory for non-compliant military processing
PIN CONFIGURATION
BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT 10 BIT 11 BIT 12 BIT 13
1 2 3 4 5 6 7 8 9 10 11
See Packaging Section for Package Dimensions
N/C BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT 10 BIT 11 BIT 12 BIT 13
1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13
22 21 20 19 18 17 16 15 14 13 12
BIT 2 BIT 1 (MSB) GND IOUT2 IOUT1 RFB VREF VDD BIT 16 (LSB) BIT 15 BIT 14
BIT 2 BIT 1 (MSB) GND IOUT2 IOUT1 RFB VREF VDD BIT 16 (LSB) BIT 15 BIT 14 N/C
22 Pin CDIP, PDIP (0.400") D22, N22
24 Pin SOIC (Jedec, 0.300") S24
PIN OUT DEFINITIONS
DIP SOIC 1 2 3 4 5 6 7 8 9 10 11 12 NAME N/C BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 BIT 8 BIT 9 BIT 10 BIT 11 BIT 12 BIT 13 DESCRIPTION No Connection Data Input Bit 3 Data Input Bit 4 Data Input Bit 5 Data Input Bit 6 Data Input Bit 7 Data Input Bit 8 Data Input Bit 9 Data Input Bit 10 Data Input Bit 11 Data Input Bit 12 Data Input Bit 13 DIP SOIC 13 14 15 16 17 18 19 20 21 22 23 24 NAME N/C BIT 14 BIT 15 BIT 16 VDD VREF RFB IOUT1 IOUT2 GND BIT 1 BIT 2 DESCRIPTION No Connection Data Input Bit 14 Data Input Bit 15 Data Input Bit 16 (LSB) Positive Power Supply Reference Input Voltage Internal Feedback Resistor Current Output 1 Current Output 2 Ground Data Input Bit 1 (MSB) Data Input Bit 2
1 2 3 4 5 6 7 8 9 10 11
12 13 14 15 16 17 18 19 20 21 22
Rev. 2.00 2
MP7616
ELECTRICAL CHARACTERISTICS
(VDD = + 15 V, VREF = +10 V unless otherwise noted)
25C Typ Tmin to Tmax Min Max
Parameter STATIC PERFORMANCE1 Resolution (All Grades) Integral Non-Linearity5 (Relative Accuracy) J K, T Differential Non-Linearity5 J K, T Gain Error Gain Temperature Coefficient2
Symbol
Min
Max
Units
Test Conditions/Comments FSR = Full Scale Range
N INL
16
16
Bits LSB Best Fit Straight Line Spec. (Max INL - Min INL) / 2
+14 +7 DNL +16 +8 GE TCGE +0.8
+14 +7 LSB +16 +8 % FSR +2.0 +0.5 +0.5 ppm/C ppm/C ppm/C ppm/% nA |Gain/VDD| VDD = + 5% Using Internal RFB Gain/Temperature
Non-Linearity Tempco2 Differential Linearity Tempco2 Power Supply Rejection Ratio Output Leakage Current6 DYNAMIC PERFORMANCE2 Current Settling Time Feedthrough at IOUT1 REFERENCE INPUT Input Resistance DIGITAL INPUTS3 Logical "1" Voltage Logical "0" Voltage Input Leakage Current ANALOG OUTPUTS2 Output Capacitance COUT1 COUT1 COUT2 COUT2 POWER SUPPLY4 Functional Voltage Range2 Supply Current VDD IDD 4.5 15 0.4 16 4 4.5 100 50 50 100 VIH VIL ILKG 3.0 2.4 0.8 +1.0 3.0 RIN 1 3 10 1 tS FT 2 1 2 PSRR IOUT +5 +1 +50 +10
+50 +200
s mV p-p
To 0.01% of FSR; all digital inputs low to high and high to low VREF = 10kHz, 20 Vp-p
10
k
0.8 +1.0
V V A
pF pF pF pF
DAC Inputs all 1's DAC Inputs all 0's DAC Inputs all 1's DAC Inputs all 0's
16 4
V mA
All digital inputs = 0 V or all = 5 V
Rev. 2.00 3
MP7616
ELECTRICAL CHARACTERISTICS (CONT'D)
NOTES: 1 Full Scale Range (FSR) is 10V for unipolar mode. 2 Guaranteed but not production tested. 3 Digital input levels should not go below ground or exceed the positive supply voltage, otherwise damage may occur. 4 Specified values guarantee functionality. Refer to other parameters for accuracy. 5 Linearity error is degraded by 65V for every mV of voltage offset at output amplifier. 6 Output leakage current refers to IOUT1. One LSB of current constantly flows into IOUT2 (30nA at 5k input impedance, VREF = +10 V) due to ladder termination into IOUT2.
Specifications are subject to change without notice
ABSOLUTE MAXIMUM RATINGS (TA = +25C unless otherwise noted)1, 2
VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to +17 V Digital Input Voltage to GND . . . . GND -0.5 to VDD +0.5 V IOUT1, IOUT2 to GND . . . . . . . . . . . GND -0.5 to VDD +0.5 V VREF to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +25 V VRFB to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +25 V Storage Temperature . . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature (Soldering, 10 seconds) . . . . . . +300C Package Power Dissipation Rating to 75C CDIP, PDIP, SOIC . . . . . . . . . . . . . . . . . . . . . . . . 1000mW Derates above 75C . . . . . . . . . . . . . . . . . . . . . 13mW/C
NOTES: 1 Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation at or above this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2 Any input pin which can see a value outside the absolute maximum ratings should be protected by Schottky diode clamps (HP5082-2835) from input pin to the supplies.
APPLICATION NOTES Refer to Section 8 for Applications Information
Rev. 2.00 4
MP7616
22 LEAD CERAMIC DUAL-IN-LINE (400 MIL CDIP) D22
S1
22
S
12
See Note 1
1 11
E1 D Base Plane Seating Plane L e b b1 c L1 Q A E
INCHES SYMBOL A b b1 c D E E1 e L L1 Q S S1 MIN -- 0.014 0.038 0.008 -- 0.350 0.390 MAX .225 0.023 0.065 0.015 1.111 0.410 0.420
MILLIMETERS MIN -- 0.356 0.965 0.203 -- 8.89 9.91 MAX 5.72 0.584 1.65 0.381 28.22 10.41 10.67 NOTES -- -- 2 -- 4 4 7 5 -- -- 3 6 6 --
NOTES 1. Index area; a notch or a lead one identification mark is located adjacent to lead one and is within the shaded area shown. 2. The minimum limit for dimension b1 may be 0.023 (0.58 mm) for all four corner leads only. 3. Dimension Q shall be measured from the seating plane to the base plane. 4. This dimension allows for off-center lid, meniscus and glass overrun. 5. The basic lead spacing is 0.100 inch (2.54 mm) between centerlines. 6. Applies to all four corners. 7. This is measured to outside of lead, not center.
0.100 BSC 0.125 0.150 0.015 -- 0.005 0 0.200 -- 0.070 0.080 -- 15
2.54 BSC 3.18 3.81 0.381 -- 0.13 0 5.08 -- 1.78 2.03 -- 15
Rev. 2.00 5
MP7616
22 LEAD PLASTIC DUAL-IN-LINE (400 MIL PDIP) N22
S
22 1 Q1 D
12 E1 11 E A1
Seating Plane
A L B e B1
C
INCHES SYMBOL A A1 B B1 (1) C D E E1 e L MIN -- 0.015 0.014 0.038 0.008 1.050 0.385 0.330 MAX 0.225 -- 0.023 0.065 0.015 1.110 0.425 0.380
MILLIMETERS MIN -- 0.38 0.356 0.965 0.203 26.67 9.78 8.38 MAX 5.72 -- 0.584 1.65 0.381 28.19 10.80 9.65
0.100 BSC 0.115 0 0.055 0.040 (1) 0.150 15 0.070 0.080
2.54 BSC 2.92 0 1.40 1.02 3.81 15 1.78 2.03
Q1 S Note:
The minimum limit for dimensions B1 may be 0.023" (0.58 mm) for all four corner leads only.
Rev. 2.00 6
MP7616
24 LEAD SMALL OUTLINE (300 MIL JEDEC SOIC) S24
D
24
13
E
H
12
h x 45 C Seating Plane e B A1 L A
INCHES SYMBOL A A1 B C D E e H h L MIN 0.097 0.0050 0.014 0.0091 0.602 0.292 MAX 0.104 0.0115 0.019 0.0125 0.612 0.299
MILLIMETERS MIN 2.464 0.127 0.356 0.231 15.29 7.42 MAX 2.642 0.292 0.483 0.318 15.54 7.59
0.050 BSC 0.400 0.010 0.016 0 0.410 0.016 0.035 8
1.27 BSC 10.16 0.254 0.406 0 10.41 0.406 0.889 8
Rev. 2.00 7
MP7616
NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contains here in are only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright EXAR Corporation Datasheet April 1995 Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
Rev. 2.00 8

▲Up To Search▲

Price & Availability of MP7616

	To Download MP7616 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .