Part Number Hot Search : 
SD4017 X935Z 2N517 SP233 ALDL190G FR202GP T125A 2060CT
Product Description
Full Text Search
 

To Download EL4332 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 (R)
EL4332
Data Sheet October 4, 2004 FN7163.2
Triple 2:1 300MHz Mux-Amp AV = 2
The EL4332 is a triple very high speed 2:1 MultiplexerAmplifier. It is intended primarily for component video multiplexing and is especially suited for pixel switching. The amplifiers have their gain set to 2 internally, which reduces the need for many external components. The gain-of-2 facilitates driving back terminated cables. All three amplifiers are switched simultaneously from their A to B inputs by the TTL/CMOS compatible, common A/B control pin. A -3dB bandwidth of 300MHz together with 3ns multiplexing time enable the full performance of the fastest component video systems to be realized. The EL4332 runs from standard 5V supplies, and is available in the narrow 16-pin small outline package.
Features
* 3ns A-B switching * 300MHz bandwidth * Fixed gain of 2, for cable driving * > 650V/s slew rate * TTL/CMOS compatible switch * Pb-free available
Applications
* RGB multiplexing * Picture-in-picture * Cable driving * HDTV processing * Switched gain amplifiers
Pinout
EL4332 [16-PIN SO (0.150")] TOP VIEW
* ADC input multiplexer
Ordering Information
PART NUMBER EL4332CS EL4332CS-T7 EL4332CS-T13 EL4332CSZ (Note) EL4332CSZ-T7 (Note) EL4332CSZ-T13 (Note) PACKAGE 16-Pin SO (0.150") 16-Pin SO (0.150") 16-Pin SO (0.150") 16-Pin SO (0.150") (Pb-Free) 16-Pin SO (0.150") (Pb-Free) 16-Pin SO (0.150") (Pb-Free) TAPE & REEL 7" 13" 7" 13" PKG. DWG. # MDP0027 MDP0027 MDP0027 MDP0027 MDP0027 MDP0027
NOTE: Intersil Pb-free products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which is compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J Std-020B.
Demo Board
A demo PCB is available for this product.
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2002-2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners.
EL4332
Absolute Maximum Ratings (TA = 25C)
VCC to VEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14V VCC to any GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V VEE to any GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 45mA Any Input . . . . . . . . . . . . . . . . . . . . . . . . . . VEE -0.3V to VCC +0.3V Input Current, Any Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Ambient Operating Temperature . . . . . . . . . . . . . . . . . -40C to 85C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-60C to +150C
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER VOS dVOS RIN IB dIB AV dAV CIN PSRR VO
VCC = +5V, VEE = -5V, Temperature = 25C, RL = DESCRIPTION MIN TYP 8 2 30 -7 0.5 1.94 2.00 0.5 3.3 50 2.7 70 3.6 +3/-2.7 30 -70 -70 2.0 0.8 -0.3 -3 38 -40 0 48 -80 3 60 40 -100 -100 -30 4.0 2.06 2.5 MAX 20 8 UNITS mV mV k A A V/V % pF dB V V mA dB dB V V A A mA
Input Referred Offset Voltage Input Referred Offset Voltage Delta (Note 1) Input Resistance Input Bias Current Input Bias Current Delta (Note 1) Gain Gain Delta (Note 1) Input Capacitance Power Supply Rejection Ratio Output Voltage Swing into 500 load Output Voltage Swing into 150 load
IOUT XtalkAB XtalkCH-CH VIH VIL IIL IIH IS NOTES:
Current Output, Measured with 75 Load (Note 2) Crosstalk from Non-selected Input (at DC) Crosstalk from one Amplifier to another Amplifier Input Logic High Level Input Logic Low Level Logic Low Input Current (VIN = 0V) Logic High Input Current (VIN = 0V) Total Supply Current
1. Each channel's A-input to its B-input. 2. There is no short circuit protection on any output.
AC Electrical Specifications
PARAMETER BW BW 0.1dB DG DP Pkg SR
VCC = +5V, VEE = -5V, Temperature = 25C, RL = 150, CL = 3pF. DESCRIPTION MIN TYP 300 105 0.04 0.08 0.2 650 MAX UNITS MHz MHz % dB V/s
-3dB Bandwidth 0.1dB Bandwidth Differential Gain at 3.58MHz Differential Phase at 3.58MHz Peaking with Nominal Load Slew Rate (4V Square Wave, Measured 25%-75%)
2
EL4332
AC Electrical Specifications
PARAMETER tS TSW OS ISOab 10M 100M ISOch-ch 10M 100M VCC = +5V, VEE = -5V, Temperature = 25C, RL = 150, CL = 3pF. (Continued) DESCRIPTION Settling Time to 0.1% of Final Value Time to Switch Inputs Overshoot, VOUT = 4VP-P Input to Input Isolation at 10MHz Input to Input Isolation at 100MHz Channel to Channel Isolation at 10MHz Channel to Channel Isolation at 100MHz MIN TYP 13 3 8 60 40 61 50 MAX UNITS ns ns % dB dB dB dB
Pin Descriptions
PIN NAME A1, A2, A3 B1, B2, B3 GND1, GND2, GND3 Out1, Out2, Out3 VCC VEE A/B "A" inputs to amplifiers 1, 2 and 3 respectively. "B" inputs to amplifiers 1, 2 and 3 respectively. These are the individual ground pins for each channel. Amplifier outputs. Note: there is no short circuit protection on any output. Positive power supply. Typically +5V. Negative power supply. Typically -5V. Common input select pin, a logic high selects the "A" inputs, logic low selects the "B" inputs. CMOS/TTL compatible. FUNCTION
Burn In Schematic
3
EL4332 Typical Performance Curves
FIGURE 1. SMALL SIGNAL TRANSIENT RESPONSE
FIGURE 2. LARGE SIGNAL TRANSIENT RESPONSE
FIGURE 3. SWITCHING TO GROUND FROM A LARGE SIGNAL UNCORRELATED SINE WAVE
FIGURE 4. SWITCHING FROM GROUND TO A LARGE SIGNAL UNCORRELATED SINE WAVE
FIGURE 5. SWITCHING TO GROUND FROM A SMALL SIGNAL UNCORRELATED SINE WAVE
FIGURE 6. SWITCHING FROM GROUND TO A SMALL SIGNAL UNCORRELATED SINE WAVE
FIGURE 7. SWITCHING GLITCH (INPUTS AT GROUND)
FIGURE 8. SWITCHING FROM A FAMILY OF DC LEVELS TO GROUND
4
EL4332 Typical Performance Curves
(Continued)
FIGURE 9. SWITCHING FROM GROUND TO A FAMILY OF DC LEVELS
FIGURE 10. CHANNEL A/B SWITCHING DELAY
FIGURE 11. GAIN vs FREQUENCY
FIGURE 12. GAIN vs FREQUENCY
FIGURE 13. -3dB BW vs SUPPLY VOLTAGE
FIGURE 14. BANDWIDTH vs DIE TEMPERATURE
5
EL4332 Typical Performance Curves
(Continued)
FIGURE 15. FREQUENCY RESPONSE WITH CAPACITIVE LOADS
FIGURE 16. INPUT VOLTAGE NOISE OVER FREQUENCY
FIGURE 17. A-INPUT TO B-INPUT ISOLATION
FIGURE 18. CHANNEL-CHANNEL ISOLATION
FIGURE 19. OUTPUT SWING vs SUPPLY VOLTAGE
FIGURE 20. OUTPUT SWING vs FREQUENCY
6
EL4332 Typical Performance Curves
(Continued)
FIGURE 21. SLEW RATE vs SUPPLY VOLTAGE
FIGURE 22. SLEW RATE vs DIE TEMPERATURE
JEDEC JESD51-3 LOW EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD
SO
1.2 POWER DISSIPATION (W)
1 1.136W 0.8 0.6 0.4 0.2 0 0 25
JA
16 ( =1 0 . 1 10 50 C ") /W
50
75 85 100
125
150
FIGURE 23. SUPPLY CURRENT vs SUPPLY VOLTAGE
AMBIENT TEMPERATURE (C)
FIGURE 24. POWER DISSIPATION vs AMBIENT TEMPERATURE
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL CONDUCTIVITY TEST BOARD
1.8 POWER DISSIPATION (W) 1.6
1.4 1.563W 1.2 1 0.8 0.6 0.4 0.2 0 0 25
SO
JA
16
=8
(0
0
.1 50 C/ " ) W
50
75 85 100
125
150
AMBIENT TEMPERATURE (C)
FIGURE 25. POWER DISSIPATION vs AMBIENT TEMPERATURE
7
EL4332
FIGURE 26. TYPICAL CONNECTION FOR A 2:1 COMPONENT VIDEO MULTIPLEXER
Applications Information
Figure 26 shows a typical use for the EL4332. The circuit is a component video (R,G, B or Y,U,V) multiplexer. Since the gain of the internal amplifiers has been set to 2, the only extra components needed are the supply decoupling capacitors and the back terminating resistors, if transmission lines are to be driven. The EL4332 can drive backmatched 50 or 75 loads.
Further notes and recommended practices for high speed printed circuit board layout can be found in the tutorials in the Elantec databooks.
Supplies
Supply bypassing should be as physically near the power pins as possible. Chip capacitors should be used to minimize lead inductance. Note that larger values of capacitor tend to have larger internal inductances. So when designing for 3 transmission lines or similar moderate loads, a 0.1F ceramic capacitor right next to the power pin in parallel with a 22F tantalum capacitor placed as close to the 0.1F is recommended. For lighter loadings, or if not all the channels are being used, a single 4.7F capacitor has been found quite adequate. Note that component video signals do tend to have a high level of signal correlation. This is especially true if the video signal has been derived from 3 synchronously clocked DACs. This corresponds to all three channels drawing large slew currents simultaneously from the supplies. Thus, proper bypassing is critical.
Grounds
It will be noticed that each mux-amp channel has its own separate ground pin. These ground pins have been kept separate to keep the channel separation inside the chip as large as possible. The feedback resistors use these ground pins as their reference. The resistors total 400, so there is a significant signal current flowing from these pins to ground. The ground pins should all be connected together, to a ground plane underneath the chip. 1 oz. copper for the ground plane is highly recommended.
8
EL4332
Logic Inputs
The A/B select, logic input, is internally referenced to ground. It is set at 2 diode drops above ground, to give a threshold of about 1.4V (see Figure 27). The PNP input transistor requires that the driving gate be able to sink current, typically < 30A, for a logic "low". If left to float, it will be a logic "high".
FIGURE 27. SIMPLIFIED LOGIC INPUT STAGE
The input PNP transistors have sufficient gain that a simple level shift circuit (see Figure 28) can be used to provide a simple interface with Emitter Coupled Logic. Typically, 200mV is enough to switch from a solid logic "low" to a "high."
FIGURE 28. ADAPTING THE SELECT PIN FOR ECL LOGIC LEVELS
The capacitor CFF is only in the network to prevent the A/B pin's capacitance from slowing the control signal. The network shown level shifts the ECL levels, -0.7V to -1.5V to +1.6V and +1.1V respectively. The terminating resistor, RTT, is required since the open emitter of the ECL gate can not sink current. If a -2V rail is not being used, a 220 to 330 resistor to the -5.2V rail would have the same effect.
9
EL4332
Expanding the Multiplexer
In Figure 29, a 3:1 multiplexer circuit is shown. The expansion to more inputs is very straight forward. Since the EL4332 has a fixed gain of 2, interstage attenuators may be required as shown in Figure 28. The truth table for the 3:1 multiplexer select lines is:
TABLE 1. X 0 0 1 Y 0 1 X MUX OUTPUT R3, G3, B3 R2, G2, B2 R1, G1, B1
When interstage attenuators are used, the values should be kept down in the region of 50-300. This is to prevent a combination of circuit board stray capacitance and the EL4332's input capacitance forming a significant pole. For example, if instead of 100 as shown, resistors of 1k had been used, and assuming 3pF of stray and 3pF of input capacitance, a pole would be formed at about 53MHz.
FIGURE 29. TYPICAL CONNECTION FOR A 3:1 COMPONENT VIDEO MULTIPLEXER
10
EL4332
A Bandwidth Selectable Circuit
In Figure 30, a circuit is shown that allows three signals to be either low pass filtered or full bandwidth. This could be useful where an input signal is frequently noisy. The component values shown give a Butterworth LPF response, with a -3dB frequency of 50MHz. Note again, the resistor values are low, so that stray capacitance does not affect the desired cut-off frequency.
FIGURE 30. SWITCHED 50MHz LOW PASS FILTER FOR HIGH/LOW RESOLUTION MONITORS
11
EL4332 EL4332 Macromodel
* EL4332 Macromodel * Revision A, April 1996 **************************************************************************** *Applications Hints. The EL4332 has two VCC pins, one VEE pin, and three ground *pins. The VCC pins (pins 14 and 15 are internally shorted together in the model, *but the ground pins (GND1, GND2, and GND3 (nodes 2, 7, and 10, respectively) *must be connected to ground (node 0) using a le-6W resistor. Alternatively, * nodes 2, 7, and 10 may be connected to ground through a 25 resistor in parallel * with a 4nH inductor to simulate package and PCB parasitics. **************************************************************************** * Connections: * OUT1 * | GND1 *| | A1 *| | | B1 *| | || B2 *| | || | A2 *| | || | | GND2 *| | || | | | OUT2 *| | || | | | | *| | || | | | | *1 2 3 4 5 6 7 8 * * OUT3 *| GND3 *| | B3 *| | | A3 *| | | | VEE *| | | | | VCC *| | | | | | VCC *| | | | | | | A/B *| | | | | | | | *| | | | | | | | * 9 10 11 12 13 14 15 16 ************A B Switch *************** Rshort 14 15 le-12 rshort1 15 0 100 Meg Isw 14 110 1.5 mA vref 111 0 1.6V q1 101 16 110 qp q2 102 111 110 qp R1 101 13 500 R2 102 13 500 Rd1 107 0 100 Esw 107 0 table {v(102, 101)*100} (0,0) (1,1) * ************Amplifier #1 ************* q131 103 3 112 qp q141 104 114 113 qp q151 105 4 115 qp q161 106 117 116 qp Ia11 14 112 1 mA Ia21 14 113 1 mA Ib11 14 115 1 mA Ib21 14 116 1 mA Rga1 112 113 275 Rgb1 115 116 275 R31 103 13 275 R41 104 13 275
12
EL4332
R51 105 13 275 R61 106 13 275 R71 1 114 400 R81 114 2 400 R911 117 400 R110 117 2 400 Ediff1 108 0 value {(v(104,103)*v(107))+(v(106,105)*(1-v(107)))} rdiff1 108 0 1K * *Compensation Section * ga1 0 134 108 0 1m rh1 134 0 5 Meg cc1 134 0 0.6 pF * *Poles * ep1 141 0 134 0 1.0 rpa1 141 142 200 cpa1 142 0 0.75 pF rpb1 142 143 200 cpb1 143 0 0.75 pF * *Output Stage * i011 15 150 1.0 mA i021 151 13 1.0 mA q71 13 143 150 qp q81 15 143 151 qn q91 15 150 152 qn q101 13 151 153 qp ros11 152 1 2 ros21 153 1 2 * ************Amplifier #2*********** q231 203 6 212 qp q241 204 214 213 qp q251 205 5 215 qp q261 206 217 216 qp Ia12 14 212 1 mA Ia22 14 213 1 mA Ib12 14 215 1 mA Ib22 14 216 1 mA Rga2 212 213 275 Rgb2 215 216 275 R231 203 13 275 R241 204 13 275 R251 205 13 275 R261 206 13 275 R271 8 214 400 R281 214 7 400 R291 8 217 400 R210 217 7 400 Ediff2 208 0 value {(v(204,203)*v(107))+(v(206,205)*(1-v(107)))} rdiff2 208 0 1K * * Compensation Section * ga2 0 234 208 0 1m rh2 234 0 5 Meg cc2 234 0 0.6 pF 13
EL4332
* * Poles * ep2 241 0 234 0 1.0 rpa2 241 242 200 cpa2 242 0 0.75 pF rpb2 242 243 200 cpb2 243 0 0.75 pF * *Output Stage * i0 12 15 250 1.0 mA i022 251 13 1.0 mA q271 13 243 250 qp q281 15 243 251 qn q291 15 250 252 qn q201 13 251 253 qp ros12 252 8 2 ros22 253 8 2 * ************Amplifier #3 ************ q331 303 12 312 qp q341 304 314 313 qp q351 305 11 315 qp q361 306 317 316 qp Ia13 14 312 1 mA Ia23 14 313 1 mA Ib13 14 315 1 mA Ib23 14 316 1 mA Rga3 312 313 275 Rgb3 315 316 275 R331 303 13 275 R341 304 13 275 R351 305 13 275 R361 306 13 275 R371 9 314 400 R381 314 10 400 R391 9 317 400 R310 317 10 400 Ediff3 308 0 value {( v(304,303)*(v(107))+(v(306,305)*(1-v(107)))} rdiff3 308 0 1K * * Compensation * ga3 0 334 308 01m rh3 334 0 5 Meg cc3 334 0 0.6 pF * * Poles * ep3 341 0 3340 1.0 rpa3 341 342 200 cpa3 342 0 0.75 pF rpb3 342 343 200 cpb3 343 0 0.75 pF * * Output Stage * i013 15 350 1.0 mA i023 351 13 1.0 mA q371 13 343 350 qp 14
EL4332
q381 15 343 351 qn q391 15 350 352 qn q301 13 351 353 qp ros13 352 9 2 ros23 353 9 2 * * Power Supply Current * ips 15 13 22 mA * *Models * .model qp pnp(is=1.5e-16 bf=300 tf=0.01 ns) .model qn npn(is=0.8e-18 bf=300 tf=0.01 ns) .ends
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com 15


▲Up To Search▲   

 
Price & Availability of EL4332

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X