View W39V040FBP_509216.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

W39V040FB Data Sheet 512K x 8 CMOS FLASH MEMORY WITH FWH INTERFACE
Table of Contents1. 2. 3. 4. 5. 6. GENERAL DESCRIPTION ......................................................................................................... 3 FEATURES ................................................................................................................................. 3 PIN CONFIGURATIONS............................................................................................................. 4 BLOCK DIAGRAM ...................................................................................................................... 4 PIN DESCRIPTION..................................................................................................................... 4 FUNCTIONAL DESCRIPTION.................................................................................................... 5 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 7. 7.1 7.2 7.3 7.4 7.5 7.6 7.7 7.8 8. 8.1 8.2 8.3 9. 9.1 9.2 9.3 9.4 Interface Mode Selection and Description..................................................................... 5 Read (Write) Mode ........................................................................................................ 5 Reset Operation............................................................................................................. 5 Boot Block Operation and Hardware Protection at Initial- #TBL & #WP ....................... 5 Sector Erase Command ................................................................................................ 6 Program Operation ........................................................................................................ 6 Hardware Data Protection ............................................................................................. 6 WRITE OPERATION STATUS...................................................................................... 6 General Purpose Inputs Register for FWH Mode.......................................................... 8 Product Identification Registers ..................................................................................... 8 Block Locking Registers ................................................................................................ 8 Register Based Block Locking Value Definitions Table................................................. 9 Read Lock.................................................................................................................... 10 Write Lock .................................................................................................................... 10 Lock Down ................................................................................................................... 10 Product Identification Registers ................................................................................... 10 Operating Mode Selection - Programmer Mode.......................................................... 10 Operating Mode Selection - FWH Mode...................................................................... 11 FWH Cycle Definition................................................................................................... 11 Embedded Programming Algorithm ............................................................................ 12 Embedded Erase Algorithm......................................................................................... 13 Embedded #Data Polling Algorithm............................................................................. 14 Embedded Toggle Bit Algorithm.................................................................................. 15
REGISTER FOR FWH MODE .................................................................................................... 8
TABLE OF OPERATING MODES ............................................................................................ 10
TABLE OF COMMAND DEFINITION ....................................................................................... 11
-1-
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
9.5 10. 10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11. 11.1 11.2 11.3 11.4 11.5 11.6 12. 12.1 12.2 12.3 13. 13.1 13.2 13.3 13.4 13.5 13.6 13.7 14. 15. 16. Software Product Identification and Boot Block Lockout Detection Acquisition Flow . 16 Absolute Maximum Ratings ......................................................................................... 17 Programmer interface Mode DC Operating Characteristics........................................ 17 FWH Interface Mode DC Operating Characteristics ................................................... 18 Power-up Timing.......................................................................................................... 18 Capacitance ................................................................................................................. 18 Programmer Interface Mode AC Characteristics......................................................... 19 Read Cycle Timing Parameters................................................................................... 20 Write Cycle Timing Parameters ................................................................................... 20 Data Polling and Toggle Bit Timing Parameters ......................................................... 20 Read Cycle Timing Diagram........................................................................................ 21 Write Cycle Timing Diagram ........................................................................................ 21 Program Cycle Timing Diagram .................................................................................. 22 #DATA Polling Timing Diagram................................................................................... 22 Toggle Bit Timing Diagram .......................................................................................... 23 Sector Erase Timing Diagram ..................................................................................... 23 AC Test Conditions...................................................................................................... 24 Read/Write Cycle Timing Parameters ......................................................................... 24 Reset Timing Parameters ............................................................................................ 24 Read Cycle Timing Diagram........................................................................................ 25 Write Cycle Timing Diagram ........................................................................................ 25 Program Cycle Timing Diagram .................................................................................. 26 #DATA Polling Timing Diagram................................................................................... 27 Toggle Bit Timing Diagram .......................................................................................... 28 FGPI Register/Product ID Readout Timing Diagram................................................... 30 Reset Timing Diagram ................................................................................................. 30
ELECTRICAL CHARACTERISTICS ......................................................................................... 17
TIMING WAVEFORMS FOR PROGRAMMER INTERFACE MODE ....................................... 21
FWH INTERFACE MODE AC CHARACTERISTICS................................................................ 24
TIMING WAVEFORMS FOR FWH INTERFACE MODE.......................................................... 25
ORDERING INFORMATION..................................................................................................... 31 HOW TO READ THE TOP MARKING ...................................................................................... 31 PACKAGE DIMENSIONS ......................................................................................................... 32 16.1 16.2 32L PLCC .................................................................................................................... 32 32L STSOP.................................................................................................................. 32
17.
VERSION HISTORY ................................................................................................................. 33
-2-
W39V040FB
1. GENERAL DESCRIPTION
The W39V040FB is a 4-megabit, 3.3-volt only CMOS flash memory organized as 512K x 8 bits. For flexible erase capability, the 4Mbits of data are divided into 8 uniform sectors of 64 Kbytes. The device can be programmed and erased in-system with a standard 3.3V power supply. A 12-volt VPP is required for accelerated program. The unique cell architecture of the W39V040FB results in fast program/erase operations with extremely low current consumption. This device can operate at two modes, Programmer bus interface mode, Firmware Hub (FWH) bus interface mode. As in the Programmer interface mode, it acts like the traditional flash but with a multiplexed address inputs. But in the FWH interface mode, this device complies with the Intel FWH specification. The device can also be programmed and erased using standard EPROM programmers.
2. FEATURES
*
Single 3.3-volt operations: - 3.3-volt Read - 3.3-volt Erase - 3.3-volt Program
- #TBL supports 64-Kbyte Boot Block hardware protection - #WP supports the whole chip except Boot Block hardware protection
*
*
Fast Program operation: - Byte-by-Byte programming: 9 S (typ.) (VPP = 12V) - Byte-by-Byte programming: 12 S (typ.) (VPP = Vcc)
Low power consumption - Active current: 15 mA (typ. for FWH read mode) Automatic program and erase timing with internal VPP generation End of program or erase detection - Toggle bit - Data polling Latched address and data TTL compatible I/O Available packages: 32L PLCC, 32L STSOP 32L PLCC Lead free, 32L STSOP Lead free
* *
* * * * * *
Fast Erase operation: - Sector erase 0.6 Sec. (typ.) Fast Read access time: Tkq 11 nS Endurance: 10K cycles (typ.) Twenty-year data retention 8 Even sectors with 64K bytes Any individual sector can be erased Hardware protection:
* * *
*
-3-
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
3. PIN CONFIGURATIONS 4. BLOCK DIAGRAM
#WP #TBL CLK FWH[3:0] FWH4 FWH Interface 64K BYTES BLOCK 7 64K BYTES BLOCK 6 64K BYTES BLOCK 5 64K BYTES BLOCK 4 64K BYTES BLOCK 3 Programmer Interface 64K BYTES BLOCK 2 64K BYTES BLOCK 1 64K BYTES BLOCK 0 7FFFF 70000 6FFFF 60000 5FFFF 50000 4FFFF 40000 3FFFF 30000 2FFFF 20000 1FFFF 10000 0FFFF 00000
Firmware Hub (FWH) Mode
IC #INIT #RESET R/#C A[10:0] DQ[7:0] #OE #WE RY/#BY
NC NC NC VSS IC A10(FGPI4) R/#C(CLK) V DD
Vpp
#RESET A9(FGPI3) A8(FGPI2) A7(FGPI1) A6(FGPI0) A5(#WP) A4(#TBL)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
32L STSOP
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
#OE(#INIT) #WE(FWH4) RY/#BY(RSV) DQ7(RSV) DQ6(RSV) DQ5(RSV) DQ4(RSV) DQ3(FWH3) VSS DQ2(FWH2) DQ1(FWH1) DQ0(FWH0) A0(ID0) A1(ID1) A2(ID2) A3(ID3)
5. PIN DESCRIPTION
SYM. IC #RESET #INIT #TBL #WP CLK FGPI[4:0] ID[3:0] FWH[3:0] FWH4 R/#C A[10:0] DQ[7:0] #OE #WE RY/#BY VDD VSS VPP RSV NC * * * * * * * * * * * * * * * * INTERFACE PGM FWH * * * * * * * * * * * * Reset Initialize Top Boot Block Lock Write Protect CLK Input General Purpose Inputs Identification Inputs They Are Internal Pull Down to Vss Address/Data Inputs FWH Cycle Initial Row/Column Select Address Inputs Data Inputs/Outputs Output Enable Write Enable Ready/ Busy Power Supply Ground Accelerate Program Power Supply Reserved Pins No Connection PIN NAME Interface Mode Selection
A 8 ^ F G P I 2 v 4 A7(FGPI1) A6(FGPI0) A5(#WP) A4(#TBL) A3(ID3) A2(ID2) A1(ID1) A0(ID0) DQ0(FWH0) 5 6 7 8 9 10 11 12 13 14 D Q 1 ^ F W H 1 v
A 9 ^ F G P I 3 v 3
# R E S E T 2
V P P 1
V D D 32
R / # C ^ C L K v 31
A 1 0 ^ F G P I 4 v 30 29 28 27 26 IC
V SS
NC NC
32L PLCC
25 24 23 22 21
V DD
#OE(#INIT) #WE(FWH4) RY/#BY(RSV) DQ7(RSV)
15 D Q 2 ^ F W H 2 v
16 V S S
17 D Q 3 ^ F W H 3 v
18 D Q 4 ^ R S V v
19 D Q 5 ^ R S V v
20 D Q 6 ^ R S V v
-4-
W39V040FB
6. FUNCTIONAL DESCRIPTION
6.1 Interface Mode Selection and Description
This device can operate in two interface modes, one is Programmer interface mode, and the other is FWH interface mode. The IC (Mode) pin of the device provides the control between these two interface modes. These interface modes need to be configured before power up or return from #RESET. When IC (Mode) pin is set to VDD, the device will be in the Programmer mode; while the IC (Mode) pin is set to low state (or leaved no connection), it will be in the FWH mode. In Programmer mode, this device just behaves like traditional flash parts with 8 data lines. But the row and column address inputs are multiplexed. The row address are mapped to the higher internal address A[18:11]. And the column address are mapped to the lower internal address A[10:0]. For FWH mode, it complies with the FWH Interface Specification, through the FWH[3:0] to communicate with the system chipset .
6.2 Read (Write) Mode
In Programmer interface mode, the read (write) operation of the W39V040FB is controlled by #OE (#WE). The #OE (#WE) is held low for the host to obtain (write) data from (to) the outputs (inputs). #OE is the output control and is used to gate data from the output pins. The data bus is in high impedance state when #OE is high. As for in the FWH interface mode, the read or write is determined by the "bit 0 & bit 1 of START CYCLE ". Refer to the FWH cycle definition and timing waveforms for further details.
6.3 Reset Operation
The #RESET input pin can be used in some application. When #RESET pin is at high state, the device is in normal operation mode. When #RESET pin is at low state, it will halt the device and all outputs will be at high impedance state. As the high state re-asserted to the #RESET pin, the device will return to read or standby mode, it depends on the control signals.
6.4 Boot Block Operation and Hardware Protection at Initial- #TBL & #WP
There is a hardware method to protect the top boot block and other sectors. Before power on programmer, tie the #TBL pin to low state and then the top boot block will not be programmed/erased. If #WP pin is tied to low state before power on, the other sectors will not be programmed/erased. In order to detect whether the boot block feature is set on or not, users can perform software command sequence: enter the product identification mode (see Command Codes for Identification/Boot Block Lockout Detection for specific code), and then read from address 7FFF2(hex). You can check the DQ2/DQ3 at the address 7FFF2 to see whether the #TBL/#WP pin is in low or high state. If the DQ2 is "0", it means the #TBL pin is tied to high state. In such condition, whether boot block can be programmed/erased or not will depend on software setting. On the other hand, if the DQ2 is "1", it means the #TBL pin is tied to low state, then boot block is locked no matter how the software is set. Like the DQ2, the DQ3 inversely mirrors the #WP state. If the DQ3 is "0", it means the #WP pin is in high state, then all the sectors except the boot block can be programmed/erased. On the other hand, if the DQ3 is "1", then all the sectors except the boot block are programmed/erased inhibited. To return to normal operation, perform a three-byte command sequence (or an alternate single-byte command) to exit the identification mode. For the specific code, see Command Codes for Identification/Boot Block Lockout Detection.
-5-
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
6.5 Sector Erase Command
Sector erase is a six-bus cycles operation. There are two "unlock" write cycles, followed by writing the "set-up" command. Two more "unlock" write cycles then follows by the Sector erase command. The Sector address (any address location within the desired Sector) is latched on the rising edge of R/#C in programmer mode, while the command (30H) is latched on the rising edge of #WE. Sector erase does not require the user to program the device prior to erase. When erasing a Sector, the remaining unselected sectors are not affected. The system is not required to provide any controls or timings during these operations. The automatic Sector erase begins after the erase command is completed, right from the rising edge of the #WE pulse for the last Sector erase command pulse and terminates when the data on DQ7, Data Polling, is "1" at which time the device returns to the read mode. Data Polling must be performed at an address within any of the sectors being erased. Refer to the Erase Command flow Chart using typical command strings and bus operations.
6.6 Program Operation
The W39V040FB is programmed on a byte-by-byte basis. Program operation can only change logical data "1" to logical data "0." The erase operation, which changed entire data in main memory and/or boot block from "0" to "1", is needed before programming. The program operation is initiated by a 4-byte command cycle (see Command Codes for Byte Programming). The device will internally enter the program operation immediately after the byteprogram command is entered. The internal program timer will automatically time-out (12S typ. - TBP) once it is completed and then return to normal read mode. Data polling and/or Toggle Bits can be used to detect end of program cycle.
6.7 Hardware Data Protection
The integrity of the data stored in the W39V040FB is also hardware protected in the following ways: (1) Noise/Glitch Protection: A #WE pulse of less than 5 nS in duration will not initiate a write cycle. (2) VDD Power Up/Down Detection: The programming and read operation are inhibited when VDD is less than 2.0V typical. (3) Write Inhibit Mode: Forcing #OE low or #WE high will inhibit the write operation. This prevents inadvertent writes during power-up or power-down periods.
6.8 WRITE OPERATION STATUS
The device provides several bits to determine the status of a program or erase operation: DQ5, DQ6, and DQ7. Each of DQ7 and DQ6 provides a method for determining whether a program or erase operation is complete or in progress. The device also offers a hardware-based output signal, RY/#BY in programmer mode, to determine whether an Embedded Program or Erase operation is in progress or has been completed.
DQ7: #Data Polling
The #Data Polling bit, DQ7, indicates whether an Embedded Program or Erase algorithm is in progress or completed. Data Polling is valid after the rising edge of the final #WE pulse in the command sequence.
-6-
W39V040FB
During the Embedded Program algorithm, the device outputs on DQ7 and the complement of the data programmed to DQ7. Once the Embedded Program algorithm has completed, the device outputs the data programmed to DQ7. The system must provide the program address to read valid status information on DQ7. If a program address falls within a protected sector, #Data Polling on DQ7 is active for about 1S, and then the device returns to the read mode. During the Embedded Erase algorithm, #Data Polling produces "0" on DQ7. Once the Embedded Erase algorithm has completed, #Data Polling produces "1" on DQ7. An address within any of the sectors selected for erasure must be provided to read valid status information on DQ7. Just before the completion of an Embedded Program or Erase operation, DQ7 may change asynchronously with DQ0-DQ6 while Output Enable (#OE) is set to low. That is, the device may change from providing status information to valid data on DQ7. Depending on when it samples the DQ7 output, the system may read the status or valid data. Even if the device has completed the program or erase operation and DQ7 has valid data, the data outputs on DQ0-DQ6 may be still invalid. Valid data on DQ7-DQ0 will appear on successive read cycles.
RY/#BY: Ready/#Busy
The RY/#BY is a dedicated, open-drain output pin which indicates whether an Embedded Algorithm is in progress or complete. The RY/#BY status is valid after the rising edge of the final #WE pulse in the command sequence. Since RY/#BY is an open-drain output, several RY/#BY pins can be tied together in parallel with a pull-up resistor to VDD. When the output is low (Busy), the device is actively erasing or programming. When the output is high (Ready), the device is in the read mode or standby mode.
DQ6: Toggle Bit
Toggle Bit on DQ6 indicates whether an Embedded Program or Erase algorithm is in progress or complete. Toggle Bit I may be read at any address, and is valid after the rising edge of the final #WE pulse in the command sequence (before the program or erase operation), and during the sector erase time-out. During an Embedded Program or Erase algorithm operation, successive read cycles to any address cause DQ6 to toggle. The system may use either #OE or #CE to control the read cycles. Once the operation has completed, DQ6 stops toggling. The system can use DQ6 to determine whether a sector is actively erasing. If the device is actively erasing (i.e., the Embedded Erase algorithm is in progress), DQ6 toggles. If a program address falls within a protected sector, DQ6 toggles for about 1 s after the program command sequence is written, and then returns to reading array data.
DQ5: Exceeded Timing Limits
DQ5 indicates whether the program or erase time has exceeded a specified internal pulse count limit. DQ5 produces "1" under these conditions which indicates that the program or erase cycle was not successfully completed. The device may output "1" on DQ5 if the system tries to program "1" to a location that was previously programmed to "0." Only the erase operation can change "0" back to "1." Under this condition, the device stops the operation, and while the timing limit has been exceeded, DQ5 produces "1." Under both these conditions, the system must write the reset command to return to the read mode.
-7-
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
7. REGISTER FOR FWH MODE
There are three kinds of registers on this device, the General Purpose Input Registers, the Block Lock Control Registers and Product Identification Registers. Users can access these registers through respective address in the 4Gbytes memory map. There are detail descriptions in the sections below.
7.1 General Purpose Inputs Register for FWH Mode
This register reads the FGPI[4:0] pins on the W39V040FB.This is a pass-through register which can read via memory address FFBC0100(hex). Since it is pass-through register, there is no default value. GPI Register Table
BIT FUNCTION
7-5 4 3 2 1 0
Reserved Read FGPI4 pin status Read FGPI3 pin status Read FGPI2 pin status Read FGPI1 pin status Read FGPI0 pin status
7.2 Product Identification Registers
In the FWH interface mode, a read from FFBC, 0000(hex) can output the manufacturer code, DA(hex). A read from FFBC, 0001(hex) can output the device code 54(hex). There is an alternative software method to read out the Product Identification in both the Programmer interface mode and the FWH interface mode. Thus, the programming equipment can automatically matches the device with its proper erase and programming algorithms. In the software access mode, a or JEDEC 3-byte command sequence can be used to access the product ID for programmer interface mode. A read from address 0000(hex) outputs the manufacturer code, DA(hex). A read from address 0001(hex) outputs the device code, 54(hex). The product ID operation can be terminated by a three-byte command sequence or an alternate one-byte command sequence (see Command Definition table for detail).
7.3 Block Locking Registers
This part provides 8 even 64Kbytes blocks, and each block can be locked by register control. These control registers can be set or clear through memory address. Below is the detail description. Please note that this feature is only can be applied on FWH mode.
-8-
W39V040FB
Block Locking Registers type and access memory map Table
REGISTERS REGISTERS TYPE CONTROL BLOCK DEVICE PHYSICAL ADDRESS 4GBYTES SYSTEM MEMORY ADDRESS
BLR7 BLR6 BLR5 BLR4 BLR3 BLR2 BLR1 BLR0
R/W R/W R/W R/W R/W R/W R/W R/W
7 6 5 4 3 2 1 0
7FFFFh - 70000h 6FFFFh - 60000h 5FFFFh - 50000h 4FFFFh - 40000h 3FFFFh - 30000h 2FFFFh - 20000h 1FFFFh - 10000h 0FFFFh - 00000h
FFBF0002h FFBE0002h FFBD0002h FFBC0002h FFBB0002h FFBA0002h FFB90002h FFB80002h
Block Locking Register Bits Function Table
BIT FUNCTION
7-3 2
1
0
Reserved Read Lock 1: Prohibit to read in the block where set 0: Normal read operation in the block where clear. This is default state. Lock Down 1: Prohibit further to set or clear the Read Lock or Write Lock bits. This Lock Down Bit can only be set not clear. Only the device is reset or re-powered, the Lock Down Bit is cleared. 0: Normal operation for Read Lock or Write Lock. This is the default state. Write Lock 1: Prohibited to write in the block where set. This is default state. 0: Normal programming/erase operation in the block where clear.
7.4 Register Based Block Locking Value Definitions Table
BIT [7:3] BIT 2 BIT 1 BIT 0 RESULT
00000 00000 00000 00000 00000 00000 00000 00000
0 0 0 0 1 1 1 1
0 0 1 1 0 0 1 1
0 1 0 1 0 1 0 1
Full Access. Write Lock. Default State. Locked Open (Full Access, Lock Down). Write Locked, Locked Down. Read Locked. Read & Write Locked. Read Locked, Locked Down. Read & Write Locked, Locked Down.
-9-
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
7.5 Read Lock
Any attempt to read the data of read locked block will result in "00H." The default state of any block is unlocked upon power up. User can clear or set the write lock bit anytime as long as the lock down bit is not set.
7.6 Write Lock
This is the default state of blocks upon power up. Before any program or erase to the specified block, user should clear the write lock bit first. User can clear or set the write lock bit anytime as long as the lock down bit is not set. The write lock function is in conjunction with the hardware protect pins, #WP & TBL. When hardware protect pins are enabled, it will override the register block locking functions and write lock the blocks no matter how the status of the register bits. Reading the register bit will not reflect the status of the #WP or #TBL pins.
7.7 Lock Down
The default state of lock down bit for any block is unlocked. This bit can be set only once; any further attempt to set or clear is ignored. Only the reset from #RESET or #INIT can clear the lock down bit. Once the lock down bit is set for a block, then the write lock bit & read lock bit of that block will not be set or cleared, and keep its current state.
7.8 Product Identification Registers
In the FWH interface mode, a read from FFBC, 0000(hex) can output the manufacturer code, DA(hex). A read from FFBC,0001(hex) can output the device code 54(hex). There is an alternative software method (six commands bytes) to read out the Product Identification in both the Programmer interface mode and the FWH interface mode. Thus, the programming equipment can automatically matches the device with its proper erase and programming algorithms. In the software access mode, a six-byte (or JEDEC 3-byte) command sequence can be used to access the product ID for programmer interface mode. A read from address 0000(hex) outputs the manufacturer code, DA(hex). A read from address 0001(hex) outputs the device code, 54(hex). The product ID operation can be terminated by a three-byte command sequence or an alternate one-byte command sequence (see Command Definition table for detail).
8. TABLE OF OPERATING MODES
8.1 Operating Mode Selection - Programmer Mode
MODE PINS #OE #WE #RESET ADDRESS DQ.
Read Write Standby Write Inhibit Output Disable
VIL VIH X VIL X VIH
VIH VIL X X VIH X
VIH VIH VIL VIH VIH VIH
AIN AIN X X X X
Dout Din High Z High Z/DOUT High Z/DOUT High Z
- 10 -
W39V040FB
8.2 Operating Mode Selection - FWH Mode
Operation modes in FWH interface mode are determined by "START Cycle" when it is selected. When it is not selected, its outputs (FWH[3:0]) will be disable. Please reference to the "FWH Cycle Definition".
8.3 FWH Cycle Definition
FIELD NO. OF CLOCKS DESCRIPTION
START IDSEL MSIZE TAR ADDR
1 1 1 2 7
"1101b" indicates FWH Memory Read cycle; while "1110b" indicates FWH Memory Write cycle. 0000b" appears on FWH bus to indicate the initial This one clock field indicates which FWH component is being selected. Memory Size. There is always show "0000b" for single byte access. Turned Around Time Address Phase for Memory Cycle. FWH supports the 28 bits address protocol. The addresses transfer most significant nibble first and least significant nibble last. (i.e. Address[27:24] on FWH[3:0] first, and Address[3:0] on FWH[3:0] last.) Synchronous to add wait state. "0000b" means Ready, "0101b" means Short Wait, "0110b" means Long Wait, "1001b" for DMA only, "1010b" means error, and other values are reserved. Data Phase for Memory Cycle. The data transfer least significant nibble first and most significant nibble last. (i.e. DQ[3:0] on FWH[3:0] first, then DQ[7:4] on FWH[3:0] last.)
SYNC
N
DATA
2
9. TABLE OF COMMAND DEFINITION
COMMAND DESCRIPTION Read Sector Erase Byte Program Product ID Entry (4) Product ID Exit (4) Product ID Exit NO. OF Cycles (1) 1 6 4 3 3 1 1ST CYCLE Addr. Data AIN DOUT 5555 AA 5555 AA 5555 AA 5555 AA XXXX F0 2ND CYCLE Addr. Data 2AAA 2AAA 2AAA 2AAA 55 55 55 55 3RD CYCLE Addr. Data 5555 5555 5555 5555 80 A0 90 F0 4TH CYCLE Addr. Data 5555 AA AIN DIN 5TH CYCLE Addr. Data 2AAA 55 6TH CYCLE Addr. Data SA
(5)
30
Notes: 1. The cycle means the write command cycle not the FWH clock cycle. 2. The Column Address / Row Address are mapped to the Low / High order Internal Address. i.e. Column Address A[10:0] are mapped to the internal A[10:0], Row Address A[7:0] are mapped to the internal A[18:11] 3. Address Format: A14-A0 (Hex); Data Format: DQ7-DQ0 (Hex) 4. Either one of the two Product ID Exit commands can be used. 5. SA: Sector Address SA = 7XXXXh for Unique Sector7 (Boot Sector) SA = 6XXXXh for Unique Sector6 SA = 5XXXXh for Unique Sector5 SA = 4XXXXh for Unique Sector4 SA = 3XXXXh for Unique Sector3 SA = 2XXXXh for Unique Sector2 SA = 1XXXXh for Unique Sector1 SA = 0XXXXh for Unique Sector0
- 11 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
9.1 Embedded Programming Algorithm
Start
Write Program Command Sequence (see below)
#Data Polling/ Toggle bit
Programming Completed
Program Command Sequence (Address/Command):
5555H/AAH
2AAAH/55H
5555H/A0H
Program Address/Program Data
- 12 -
W39V040FB
9.2 Embedded Erase Algorithm
Start
Write Erase Command Sequence (see below)
#Data Polling or Toggle Bit
Erasure Completed
Individual Sector Erase Command Sequence (Address/Command): 5555H/AAH
2AAAH/55H
5555H/80H
5555H/AAH
2AAAH/55H
Sector Address/30H
- 13 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
9.3 Embedded #Data Polling Algorithm
Start
Read Byte (DQ0 - DQ7) Address = SA
DQ7 = Data ? No No
Yes
DQ5 = 1 Yes Read Byte (DQ0 - DQ7) Address = SA
Yes DQ7 = Data
No Fail Pass
Note: SA = Valid address for programming .During a sector erase operation, a valid address is an address within any sector selected for erasure.
- 14 -
W39V040FB
9.4 Embedded Toggle Bit Algorithm
Start
Read Byte (DQ0-DQ7)
Read Byte (DQ0-DQ7)
No Toggle Bit =Toggle ? Yes No DQ5 = 1 ? Yes Read Byte (DQ0-DQ7) Twin
No Toggle Bit =Toggle ?
Program/Erase Operation Not Complete, Write Reset Command
Program/Erase Operation complete
Note: Recheck toggle bit because it may stop toggling as DQ5 changes to "1".
- 15 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
9.5 Software Product Identification and Boot Block Lockout Detection Acquisition Flow
Product Identification Entry (1)
Load data AA to address 5555
Identification and Boot Block Lockout Detection Mode (3)
Product
Product Identification Exit(6)
Load data AA to address 5555 (2)
Load data 55 to address 2AAA
Read address = 00000 data = DA
Load data 55 to address 2AAA
Load data 90 to address 5555
Read address = 00001 data = 54
(2)
Load data F0 to address 5555
Pause 10 S
Read address = 7FFF2 Check DQ[3:0] of data outputs
(4)
Pause 10 S
(5) Normal Mode
Notes for software product identification/boot block lockout detection: (1) Data Format: DQ7-DQ0 (Hex); Address Format: A14-A0 (Hex) (2) A1-A18 = VIL; manufacture code is read for A0 = VIL; device code is read for A0 = VIH. (3) The device does not remain in identification and boot block lockout detection mode if power down. (4) The DQ[3:2] to indicate the sectors protect status as below: 0 1 DQ2 64Kbytes Boot Block Unlocked by #TBL hardware trapping 64Kbytes Boot Block Locked by #TBL hardware trapping DQ3 Whole Chip Unlocked by #WP hardware trapping Except Boot Block Whole Chip Locked by #WP hardware trapping Except Boot Block
(5) The device returns to standard operation mode. (6) Optional 1-write cycle (write F0 (hex.) at XXXX address) can be used to exit the product identification/boot block lockout detection.
- 16 -
W39V040FB
10. ELECTRICAL CHARACTERISTICS
10.1 Absolute Maximum Ratings
PARAMETER RATING UNIT
Operating Temperature Storage Temperature Power Supply Voltage to VSS Potential D.C. Voltage on Any Pin to Ground Potential VPP Voltage Transient Voltage (<20 nS) on Any Pin to Ground Potential
0 to +70 -65 to +150 -0.5 to +4.0 -0.5 to VDD +0.5 -0.5 to +13 -1.0 to VDD +0.5
C C V V V V
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings May adversely affect the life and reliability of the device.
10.2 Programmer interface Mode DC Operating Characteristics
(VDD = 3.3V 0.3V, VSS= 0V, TA = 0 to 70 C)
PARAMETER
SYM.
TEST CONDITIONS
LIMITS MIN. TYP. MAX.
UNIT
Power Supply Current Input Leakage Current Output Leakage Current Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage
ICC ILI ILO VIL VIH VOL VOH
In Read or Write mode, all DQs open Address inputs = 3.0V/0V, at f = 3 MHz VIN = VSS to VDD VOUT = VSS to VDD IOL = 2.1 mA IOH = -0.1mA
-0.5 2.0 2.4
15 -
30 90 90 0.8 VDD +0.5 0.45 -
mA
A A V V V V
- 17 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
10.3 FWH Interface Mode DC Operating Characteristics
(VDD = 3.3V 0.3V, VSS= 0V, TA = 0 to 70 C)
PARAMETER
SYM.
TEST CONDITIONS
LIMITS MIN. TYP. MAX.
UNIT
Power Supply Current Read Power Supply Current Program/Erase Standby Current 1
ICC ICC
All Iout = 0A, CLK = 33 MHz, in FWH mode operation. CLK = 33 MHz, in FWH mode operation. FWH4 = 0.9 VDD, CLK = 33 MHz, all inputs = 0.9 VDD / 0.1 VDD no internal operation FWH4 = 0.1 VDD, CLK = 33 MHz, all inputs = 0.9 VDD /0.1 VDD no internal operation. IOL = 1.5 mA IOH = -0.5 mA
-
15 18
25 30
mA mA
Isb1
-
20
50
uA
Standby Current 2 Input Low Voltage Input Low Voltage of #INIT Input High Voltage Input High Voltage of #INIT Pin Output Low Voltage Output High Voltage
Isb2 VIL VILI VIH VIHI VOL VOH
-0.5 -0.5 0.5 VDD 1.35 V 0.9 VDD
3 -
10 0.3 VDD 0.2 VDD VDD +0.5 VDD +0.5 0.1 VDD -
mA V V V V V V
10.4 Power-up Timing
PARAMETER SYMBOL TYPICAL UNIT
Power-up to Read Operation Power-up to Write Operation
TPU. READ TPU. WRITE
100 5
S mS
10.5 Capacitance
(VDD = 3.3V, TA = 25 C, f = 1 MHz)
PARAMETER
SYMBOL
CONDITIONS
MAX.
UNIT
I/O Pin Capacitance Input Capacitance
CI/O CIN
VI/O = 0V VIN = 0V
12 6
pf pf
- 18 -
W39V040FB
10.6 Programmer Interface Mode AC Characteristics
AC Test Conditions
PARAMETER CONDITIONS
Input Pulse Levels Input Rise/Fall Time Input/Output Timing Level Output Load
0V to 0.9 VDD < 5 nS 1.5V/1.5V 1 TTL Gate and CL = 30 pF
AC Test Load and Waveform
+3.3V
1.8K
DOUT
Input
30 pF (Including Jig and Scope) 0.9VDD 1.3K 0V Test Point 1.5V
Output
1.5V Test Point
- 19 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
Programmer Interface Mode AC Characteristics, continued
10.7 Read Cycle Timing Parameters
(VDD = 3.3V 0.3V, VSS = 0V, TA = 0 to 70 C)
PARAMETER
SYMBOL
W39V040FB MIN. MAX.
UNIT
Read Cycle Time Row / Column Address Set Up Time Row / Column Address Hold Time Address Access Time Output Enable Access Time #OE Low to Active Output #OE High to High-Z Output Output Hold from Address Change
TRC TAS TAH TAA TOE TOLZ TOHZ TOH
350 50 50 0 0
150 75 35 -
nS nS nS nS nS nS nS nS
10.8 Write Cycle Timing Parameters
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
Reset Time Address Setup Time Address Hold Time R/#C to Write Enable High Time #WE Pulse Width #WE High Width Data Setup Time Data Hold Time #OE Hold Time Byte programming Time Sector Erase Cycle Time (Note 2) Program/Erase Valid to RY/#BY Delay
TRST TAS TAH TCWH TWP TWPH TDS TDH TOEH TBP TPEC TBUSY
1 50 50 50 100 100 50 50 0 90
12 0.6 -
200 6 -
S nS nS nS nS nS nS nS nS S S nS
Notes: 1. All AC timing signals observe the following guidelines for determining setup and hold times: (a) High level signal's reference level is input high and (b) low level signal's reference level is input low. Ref. to the AC testing condition. 2. Exclude 00H pre-program prior to erasure. (In the pre-programming step of the embedded erase algorithm, all bytes are programmed to 00H before erasure
10.9 Data Polling and Toggle Bit Timing Parameters
PARAMETER SYMBOL W39V040FB MIN. MAX. UNIT
#OE to Data Polling Output Delay #OE to Toggle Bit Output Delay Toggle or Polling interval
TOEP TOET
-
50
350 350 -
nS nS mS
- 20 -
W39V040FB
11. TIMING WAVEFORMS FOR PROGRAMMER INTERFACE MODE
11.1 Read Cycle Timing Diagram
#RESET TRST Column Address TAS R/#C VIH #WE #OE TAA TOH TOE High-Z DQ[7:0] TOLZ Data Valid High-Z TOHZ TAH TRC Row Address TAS TAH Column Address Row Address
A[10:0]
11.2 Write Cycle Timing Diagram
TRST #RESET
A[10:0]
Column Address TAS TAH
Row Address TAS TAH
R/ #C TCWH #OE TWP #WE TDS DQ[7:0] Data Valid TDH TWPH TOEH
- 21 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
Timing Waveforms for Programmer Interface Mode, continued
11.3 Program Cycle Timing Diagram
Byte Program Cycle A[10:0] (Internal A[18:0]) DQ[7:0] 5555 AA 2AAA 55 5555 A0
Programmed Address
Data-In
R/#C
#OE #WE TWP
TWPH
TBP
Byte 0 RY/#BY
Byte 1
Byte 2
Byte 3
Internal Write Start
TBUSY Note: The internal address A[18:0] are converted from external Column/Row address. Column/Row Address are mapped to the Low/High order internal address. i.e. Column Address A[10:0] are mapped to the internal A[10:0], Row Address A[7:0] are mapped to the internal A[18:11].
11.4 #DATA Polling Timing Diagram
A[10:0] (Internal A[18:0]) R/ #C An An An An
#WE
#OE TOEP DQ7 X X TBP RY/#BY TBUSY X X
- 22 -
W39V040FB
Timing Waveforms for Programmer Interface Mode, continued
11.5 Toggle Bit Timing Diagram
A[10:0] R/ #C
#WE
#OE TOET DQ6 TBP RY/#BY
11.6 Sector Erase Timing Diagram
Six-byte code for 3.3V-only Sector Erase A[10:0] (Internal A[18:0]) DQ[7:0] 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 SA 30
R/ #C
#OE #WE
TWP TWPH SB0 SB1 SB2 SB3 SB4 SB5
TPEC
Internal Erase starts
RY/#BY
Note: The internal address A[18:0] are converted from external Column/Row addres Column/Row Address are mapped to the Low/High order internal address i.e. Column Address A[10:0] are mapped to the internal A[10:0] Row Address A[7:0] are mapped to the internal A[18:11]. SA = Sector Address, Please ref. to the "Table of Command Definition"
TBUSY
- 23 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
12. FWH INTERFACE MODE AC CHARACTERISTICS
12.1 AC Test Conditions
PARAMETER CONDITIONS
Input Pulse Levels Input Rise/Fall Slew Rate Input/Output Timing Level Output Load
0.6 VDD to 0.2 VDD 1 V/nS 0.4VDD / 0.4VDD 1 TTL Gate and CL = 10 pF
12.2 Read/Write Cycle Timing Parameters
(VDD = 3.3V 0.3V, VSS = 0V, TA = 0 to 70 C)
PARAMETER
SYMBOL
W39V040FB MIN. MAX.
UNIT
Clock Cycle Time Input Set Up Time Input Hold Time Clock to Data Valid
TCYC TSU THD TKQ
30 7 0 2
11
nS nS nS nS
Note: Minimum and Maximum time have different load. Please refer to PCI specification.
12.3 Reset Timing Parameters
PARAMETER SYMBOL MIN. TYP. MAX. UNIT
VDD stable to Reset Active Clock Stable to Reset Active Reset Pulse Width Reset Active to Output Float Reset Inactive to Input Active
TPRST TKRST TRSTP TRSTF TRST
1 100 100 10
-
50 -
mS S nS nS S
Note: All AC timing signals observe the following guidelines for determining setup and hold times: (a) High level signal's reference level is input high and (b) low level signal's reference level is input low. Please refer to the AC testing condition.
- 24 -
W39V040FB
13. TIMING WAVEFORMS FOR FWH INTERFACE MODE
13.1 Read Cycle Timing Diagram
TCYC
CLK
#RESET
TSU THD
FWH4 Start FWH Read FWH[3:0]
IDSEL
TSU THD Address XXXXb XA[22]XXb
A[18:16] M Size
TKQ TAR 1111b Sync Data D[3:0] D[7:4] TAR 1111b Tri-State Next Start
0000b
1101b 0000b
A[15:12] A[11:8]
A[7:4]
A[3:0]
0000b
Tri-State 0000b
1 Clock 1 Clock
Load Address in 7 Clocks
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
Note: When A22 = high, the host will read the BIOS code from the FWH device. While A22 = low, the host will read the GPI (Add = FFBC0100) or Product ID (Add = FFBC0000/FFBC0001) from the FWH device
13.2 Write Cycle Timing Diagram
TCYC
CLK
#RESET
FWH4
Start FWH Write
TSU THD
IDSEL
Address XXXXb XXXXb A[18:16] A[15:12] A[11:8] Load Address in 7 Clocks A[7:4] A[3:0]
M Size
Data D[3:0] D[7:4]
TAR 1111b Tri-State
Sync 0000b 1 Clock
TAR 1111b
Next Start
FWH[3:0]
1110b 0000b
0000b
Tri-State 0000b 1 Clock
1 Clock 1 Clock
Load Data in 2 Clocks
2 Clocks
2 Clocks
- 25 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
Timing Waveforms, for FWH Interface Mode, continued
13.3 Program Cycle Timing Diagram
CLK
#RESET
FWH4
1st Start FWH[3:0 ] 1110b
IDSEL
Address
XXXXb XXXXb XXXXb X101b 0101b 0101b 0101b
M Size
Data
TAR
Sync 0000b 1 Clock
TAR
Start next command Tri-State
0000b
0000b
1010b
1010b
1111b
Tri-State
1111b
1 Clock
1 Clock
Load Address "5555" in 7 Clocks
Load Data "AA" in 2 Clocks
2 Clocks
2 Clocks
1 Clock
Write the 1st command to the device in FWH mode.
CLK
#RESET
FWH4
2nd Start FWH[3:0 ] 1110b
IDSEL
Address
XXXXb 1010b 1010b 1010b
M Size
Data
TAR
Sync 0000b 1 Clock 1111b
TAR
Start next command Tri-State
0000b
XXXXb
XXXXb
X010b
0000b
0101b
0101b
1111b
Tri-State
1 Clock
1 Clock
Load Address "2AAA" in 7 Clocks
Load Data "55" in 2 Clocks
2 Clocks
2 Clocks
1 Clock
Write the 2nd command to the device in FWH mode.
CLK
#RESET
FWH4
3rd Start FWH[3:0 ] 1110b
IDSEL
Address
XXXXb XXXXb XXXXb X101b 0101b 0101b 0101b
M Size
Data
TAR
Sync Tri-State 0000b 1 Clock 1111b
TAR
Start next command Tri-State
0000b
0000b
0000b
1010b
1111b
1 Clock
1 Clock
Load Address "5555" in 7 Clocks
Load Data "A0" in 2 Clocks
2 Clocks
2 Clocks
1 Clock
Write the 3rd command to the device in FWH mode.
CLK
#RESET
FWH4
Internal program start Address Data TAR Sync Tri-State 0000b 1 Clock 1111b TAR
4th Start FWH[3:0 ] 1110b
IDSEL
M Size
0000b
XXXXb
XXXXb
A[18:16]
A[15:12]
A[11:8]
A[7:4]
A[3:0]
0000b
D[3:0]
D[7:4]
1111b
Tri-State
Internal program start
1 Clock
1 Clock
Load Ain in 7 Clocks
Load Din in 2 Clocks
2 Clocks
2 Clocks
Write the 4th command(target location to be programmed) to the device in FWH mode.
- 26 -
W39V040FB
Timing Waveforms for FWH Interface Mode, continued
13.4 #DATA Polling Timing Diagram
CLK
#RESET
FWH4 Start FWH[3:0] 1110b IDSEL 0000b
XXXXb XXXXb
An[18:16]
Address
An[15:12] An[11:8] An[7:4] An[3:0]
M Size
Data Dn[3:0] Dn[7:4] 1111b
TAR Tri-State
Sync 0000b
TAR 1111b Tri-State
Next Start
0000b
1 Clock 1 Clock
Load Address "An" in 7 Clocks
Load Data "Dn" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the last command(program or erase) to the device in FWH mode.
CLK
#RESET XXXXb FWH4 Start FWH[3:0] 1101b IDSEL 0000b
XXXXb XXXXb
An[18:16]
Address
An[15:12] An[11:8] An[7:4] An[3:0]
M Size
TAR 1111b Tri-State
Sync 0000b
Data XXXXb Dn7,xxx
TAR 1111b Tri-State
Next Start
0000b
1 Clock 1 Clock
Load Address in 7 Clocks
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
Read the DQ7 to see if the internal write complete or not.
CLK
#RESET
FWH4 Start FWH[3:0] 1101b IDSEL 0000b
XXXXb XXXXb
An[18:16]
Address
An[15:12] An[11:8] An[7:4] An[3:0]
M Size
TAR 1111b Tri-State
Sync 0000b
Data XXXXb Dn7,xxx
TAR 1111b Tri-State
Next Start
0000b
1 Clock 1 Clock
Load Address in 7 Clocks
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
When internal write complete, the DQ7 will equal to Dn7.
- 27 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
Timing Waveforms for FWH Interface Mode, continued
13.5 Toggle Bit Timing Diagram
CLK
#RESET
FWH4 Start FWH[3:0] IDSEL
XXXXb XXXXb
Address
A[18:16]
A[15:12] A[11:8] A[7:4] A[3:0]
M Size
Data D[3:0] D[7:4] 1111b
TAR Tri-State
Sync 0000b
TAR 1111b Tri-State
Next Start
1110b 0000b
0000b
1 Clock 1 Clock
Load Address "An" in 7 Clocks
Load Data "Dn" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the last command(program or erase) to the device in FWH mode.
CLK
#RESET
FWH4 Start FWH[3:0] 1101b IDSEL 0000b
XXXXb XXXXb XXXXb
Address XXXXb XXXXb XXXXb XXXXb
M Size
TAR 1111b Tri-State
Sync 0000b
Data XXXXb
X,D6,XXb
TAR 1111b Tri-State
Next Start
0000b
1 Clock 1 Clock
Load Address in 7 Clocks
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
Read the DQ6 to see if the internal write complete or not.
CLK
#RESET
FWH4 Start FWH[3:0] IDSEL
XXXXb XXXXb XXXXb
Address XXXXb XXXXb XXXXb XXXXb
M Size
TAR 1111b Tri-State
Sync 0000b
Data XXXXb
X,D6,XXb
TAR 1111b Tri-State
Next Start
1101b 0000b
0000b
1 Clock 1 Clock
Load Address in 7 Clocks
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
When internal write complete, the DQ6 will stop toggle.
- 28 -
W39V040FB
Timing Waveforms for FWH Interface Mode, continued
Sector Erase Timing Diagram
CLK
#RESET
FWH4 Address
XXXXb XXXXb XXXXb
1st Start IDSEL FWH[3:0] 1110b 0000b
M Size
Data 1010b 1010b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State
Start next command
X101b
0101b
0101b
0101b
0000b
1 Clock 1 Clock
Load Address "5555" in 7 Clocks
Load Data "AA" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the 1st command to the device in FWH mode.
CLK
#RESET
FWH4 Address
XXXXb XXXXb XXXXb
2nd Start IDSEL FWH[3:0] 1110b 0000b
M Size
Data 0101b 0101b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State
Start next command
X010b
1010b
1010b
1010b
0000b
1 Clock 1 Clock
Load Address "2AAA" in 7 Clocks
Load Data "55" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the 2nd command to the device in FWH mode.
CLK
#RESET
FWH4
M Size
3rd Start IDSEL FWH[3:0] 1110b 0000b
XXXXb XXXXb XXXXb
Address X101b 0101b 0101b 0101b
Data 0000b 1000b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State
Start next command
0000b
1 Clocks Clocks 1
Load Address "5555" in 7 Clocks
Load Data "80" in 2 Clocks
2 Clocks
1 Clocks
2 Clocks
1 Clocks
Write the 3rd command to the device in FWH mode.
CLK
#RESET
FWH4
FWH[3:0]
4th Start IDSEL 1110b 0000b
XXXXb XXXXb XXXXb
Address X101b 0101b 0101b 0101b
M Size
Data 1010b 1010b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State
Start next command
0000b
1 Clock 1 Clock
Load Address "5555" in 7 Clocks
Load Data "AA" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the 4th command to the device in FWH mode.
CLK
#RESET
FWH4 Start next command
5th Start IDSEL FWH[3:0] 1110b 0000b
XXXXb XXXXb XXXXb
Address X010b 1010b 1010b 1010b
M Size
Data 0101b 0101b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State
0000b
1 Clock 1 Clock
Load Address "2AAA" in 7 Clocks
Load Data "55" in 2 Clocks
2 Clocks
1 Clock
2 Clocks
1 Clock
Write the 5th command to the device in FWH mode.
CLK
#RESET
FWH4
Internal erase start 6th Start IDSEL
XXXXb XXXXb
Address
A[18:16]
M Size
Data 0000b 0011b
TAR 1111b Tri-State
Sync 0000b
TAR 1111b Tri-State Internal erase start
FWH[3:0] 1110b 0000b
XXXXb
XXXXb
XXXXb
XXXXb
0000b
1 Clock 1 Clock
Load Sector Address in 7 Clocks
Load Din in 2 Clocks
2 Clocks
1 Clock
2 Clocks
Write the 6th command(target sector to be erased) to the device in FWH mode.
- 29 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
Timing Waveforms for FWH Interface Mode, continued
13.6 FGPI Register/Product ID Readout Timing Diagram
CLK #RESET
FWH4
Start FWH[3:0] 1101b
IDSEL 0000b A[27:24] A[23:20] A[19:16]
Address 0000b 0001b /0000b 0000b 0000b /0001b
M Size
TAR Tri-State 1111b
Sync 0000b D[3:0]
Data D[7:4]
TAR Tri-State 1111b
Next Sta
0000b
1 Clock 1 Clock
Load Address "FFBC0100(hex)" in 7 Clocks for GPI Register & "FFBC0000(hex)/FFBC0001(hex) for Product ID
2 Clocks
1 Clock Data out 2 Clocks
2 Clocks
1 Clock
Note: During the GPI read out mode, the DQ[4:0] will capture the states(High or Low) of the FGPI[4:0] input pins. The DQ[7:5] are reserved pins
13.7 Reset Timing Diagram
VDD
TPRST
CLK TKRST TRSTP #RESET TRSTF FWH[3:0] TRST
FWH4
- 30 -
W39V040FB
14. ORDERING INFORMATION
PART NO. ACCESS TIME (nS) POWER SUPPLY CURRENT MAX. (mA) STANDBY VDD CURRENT MAX. (mA) PACKAGE
W39V040FBP W39V040FBQ W39V040FBPZ W39V040FBQZ
Notes:
11 11 11 11
30 30 30 30
10 10 10 10
32L PLCC 32L STSOP 32L PLCC Lead free 32L STSOP Lead free
1. Winbond reserves the right to make changes to its products without prior notice. 2. Purchasers are responsible for performing appropriate quality assurance testing on products intended for use in applications where personal injury might occur as a consequence of product failure.
15. HOW TO READ THE TOP MARKING
Example: The top marking of 32-pin STSOP W39V040FBQ
W39V040FBQ 2138977A-A12 345OBFA
1st line: Winbond logo 2nd line: the part number: W39V040FBQ 3rd line: the lot number 4th line: the tracking code: 345 O B FA 149: Packages made in '03, week 45 O: Assembly house ID: A means ASE, O means OSE, ...etc. B: IC revision; A means version A, B means version B, ...etc. FA: Process code
- 31 -
Publication Release Date: April 14, 2005 Revision A3
W39V040FB
16. PACKAGE DIMENSIONS
16.1 32L PLCC
Symbol
HE E
Dimension in Inches
Dimension in mm
Min. Nom. Max.
0.140 0.020 0.105 0.026 0.016 0.008 0.547 0.447 0.044 0.490 0.390 0.585 0.485 0.075 0.110 0.028 0.018 0.010 0.550 0.450 0.050 0.510 0.410 0.590 0.490 0.090 0.115 0.032 0.022 0.014 0.553 0.453 0.056 0.530 0.430 0.595 0.495 0.095 0.004 0 10
Min. Nom. Max.
3.56 0.50 2.67 0.66 0.41 0.20 13.89 11.35 1.12 12.45 9.91 14.86 12.32 1.91 2.80 0.71 0.46 0.25 13.97 11.43 1.27 12.95 10.41 14.99 12.45 2.29 2.93 0.81 0.56 0.35 14.05 11.51 1.42 13.46 10.92 15.11 12.57 2.41 0.10 0 10
4
1
32
30
5
29
GD D HD
13
21
A A1 A2 b1 b c D E e GD GE HD HE L y Notes:
14
20
c
L A2 A
1. Dimensions D & E do not include interlead flash. 2. Dimension b1 does not include dambar protrusion/intrusio 3. Controlling dimension: Inches 4. General appearance spec. should be based on final visual inspection sepc.
Seating Plane
e
b b1 GE
A1 y
16.2 32L STSOP
HD D c
Symbol Dimension in Inches Dimension in mm Min. Nom. Max.
0.047 0.002 0.035 0.007 0.004 0.040 0.009 ----0.488 0.315 0.551 0.020 0.020 0.000 0 3 0.024 0.031 0.004 5 0.00 0 3 0.028 0.50 0.006 0.041 0.010 0.008 0.05 0.95 0.17 0.10 1.00 0.22 ----12.40 8.00 14.00 0.50 0.60 0.80 0.10 5 0.70
e
E A A1 A2 b c D E HD e L L1 Y
Min. Nom. Max.
1.20 0.15 1.05 0.27 0.21
b
L L1
A1 A2 A
Y
- 32 -
W39V040FB
17. VERSION HISTORY
VERSION DATE PAGE DESCRIPTION
A1
August 19, 2004
-
Initial Issued Modify Isb1, Tbp, Tpec, Icc (read) Add Icc (program/erase) and Toggle or polling interval Power supply voltage to Vss potential Add important notice
A2
October 4, 2004
3, 17, 18, 20
A3
April 14 ,2005
33
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Winbond products are not intended for applications wherein failure of Winbond products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Winbond customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Winbond for any damages resulting from such improper use or sales.
Headquarters
No. 4, Creation Rd. III, Science-Based Industrial Park, Hsinchu, Taiwan TEL: 886-3-5770066 FAX: 886-3-5665577 http://www.winbond.com.tw/
Winbond Electronics Corporation America
2727 North First Street, San Jose, CA 95134, U.S.A. TEL: 1-408-9436666 FAX: 1-408-5441798
Winbond Electronics (Shanghai) Ltd.
27F, 2299 Yan An W. Rd. Shanghai, 200336 China TEL: 86-21-62365999 FAX: 86-21-62365998
Taipei Office
9F, No.480, Rueiguang Rd., Neihu District, Taipei, 114, Taiwan, R.O.C. TEL: 886-2-8177-7168 FAX: 886-2-8751-3579
Winbond Electronics Corporation Japan
7F Daini-ueno BLDG, 3-7-18 Shinyokohama Kohoku-ku, Yokohama, 222-0033 TEL: 81-45-4781881 FAX: 81-45-4781800
Winbond Electronics (H.K.) Ltd.
Unit 9-15, 22F, Millennium City, No. 378 Kwun Tong Rd., Kowloon, Hong Kong TEL: 852-27513100 FAX: 852-27552064
Please note that all data and specifications are subject to change without notice. All the trade marks of products and companies mentioned in this data sheet belong to their respective owners.
- 33 -
Publication Release Date: April 14, 2005 Revision A3

▲Up To Search▲

Price & Availability of W39V040FBP

	To Download W39V040FBP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .