View LQ104S1DG21_593223.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRODUCT SPECIFICATIONS
(R)
Liquid Crystal Displays Group
LQ104S1DG21
TFT-LCD Module
(Model No.: LQ104S1DG21)
Spec No.: LD-14304 Issue Date: April 4, 2002
1.
Application This specifications applies to color TFT-LCD module, LQ104S1DG21. These specifications sheets are the proprietary product of SHARP CORPORATION("SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP . The device listed in these specifications sheets was designed and manufactured for use in general electronic equipment. In case of using the device for applications such as control and safety equipment for transportation(aircraft, trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which require higher reliability and safety, take into consideration that appropriate measures such as fail-safe functions and redundant system design should be taken . Do not use the device for equipment that requires an extreme level of reliability, such as aerospace applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or other equipment for life support . SHARP assumes no responsibility for any damage resulting from the use of the device which does not comply with the instructions and the precautions specified in these specifications sheets . Contact and consult with a SHARP sales representative for any questions about this device .
2.
Overview This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control circuit and power supply circuit and a backlight unit. Graphics and texts can be displayed on a 800 3 600 dots panel with 262,144 colors by supplying 18 bit data signal (6bit/color), four timing signals, +3.3V or +5V DC supply voltage for TFT-LCD panel driving and supply voltage for backlight. The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation type. Therefore, this module is also suitable for the multimedia use. Optimum viewing direction is 6 o'clock. Backlight-driving DC/AC inverter is not built in this module.
3. Mechanical Specifications Parameter Display size Active area Pixel format 26 (10.4") 211.2(H) 800(H) (1 pixel Pixel pitch Pixel configuration Display mode Unit outline dimensions *1 (excluding backlight cables) Mass Surface treatment 0.264(H) Specifications Diagonal 158.4(V) 600(V) R G B dots) 0.264(V) mm Unit cm mm pixel
R,G,B vertical stripe Normally white 246.5(W) 179.4(H) 15.5max(D) Outline dimensions is shown in Fig.1 620 max Anti-glare and hard-coating g mm
4. Input Terminals 4-1. TFT-LCD panel driving Connector name :CN1 Used connector:DF9MA-41P-1V (Hirose Electric Co., Ltd.) Corresponding connector: DF9-41S-1V,DF9A-41S-1V,DF9B-41S-1V,DF9M-41S-1V
Pin
Rear side
CN1(I/F connector)
41
2
40
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41
Symbol GND CK GND Hsync Vsync GND GND GND R0 R1 R2 GND R3 R4 R5 GND GND GND G0 G1 G2 GND G3 G4 G5 GND GND GND B0 B1 B2 GND B3 B4 B5 GND ENAB R/L Vcc Vcc U/D
Function Clock signal for sampling each data signal Horizontal synchronous signal Vertical synchronous signal
Remark
Note1 Note1
data signal(LSB data signal data signal data signal data signal data signal(MSB)
data signal(LSB) data signal data signal data signal data signal data signal(MSB)
data signal(LSB) data signal data signal data signal data signal data signal(MSB) Signal to settle the horizontal display position Horizontal display mode select signal power supply (+3.3Vor+5.0V) power supply (+3.3Vor+5.0V) Vertical display mode select signal Note2
The shielding case is connected with GND. Note1 The polarity of both synchronous signals are negative. Note2 The horizontal display start timing is settled in accordance with a rising timing of ENAB
signal. In case ENAB is fixed "Low", the horizontal start timing is determined as described in 7-2. Don't keep ENAB High" during operation.
Note3 R/L=High U/D=Low
R/L=Low U/D=Low
Please do not use this terminal by "open".
Note4 R/L=High U/D=High Please do not use this terminal by "open".
R/L=Low U/D=High
4-2. Backlight driving Connector name :CN2 CN3 Used connector : BHR-03VS-1(JST) Corresponding connector :SM02(8.0)B-BHS(JST) Pin no. 1 2 3 Symbol
HIGH
Function Power supply for lamp (High voltage side)
Cable color Pink
NC
LOW
This is electrically opened. Power supply for lamp (Low voltage side) White
5. Absolute Maximum Ratings Parameter Input voltage +5V supply voltage Storage temperature Operating temperature (Ambient) Symbol VI Vcc Tstg Topa Condition Ta=25 Ta=25 Ratings 0.3 0 -35 -10 +5.5 6 70 65 Note2 Unit Remark Note1
Note1 CK,R0 R5,G0 G5,B0 B5,Hsync,Vsync,ENAB, R/L, U/L Note2 Humidity 95%RH Max. at Ta 50 . Maximum wet-bulb temperature at 39 Note3 Humidity 95%RH Max. at Ta 40 . Maximum wet-bulb temperature at 39 or less at Ta>40 . No condensation. or less at Ta>50 . No condensation.
6. Electrical Characteristics 6-1.TFT-LCDpaneldriving Ta 25 Power Supply Current dissipation Permissive input ripple voltage Input voltage (Low) Input voltage (High) Input current (low) Input current (High) NOTE 1 Vcc-turn-on conditions
VCC 2.8V 0.3V T T 0.3V T1 T 2.8V VCC
Parameter Supply voltage
Symbol Vcc Icc Icc VRF VIL VIH IOL1 IOL2 IOH1 IOH2
Min. Typ. Max. +3.0 +3.3 +5.0 +5.5 310 330 450 470 100 0.9 2.4 1.0 60.0 1.0 60.0
Unit V
Remark Note1 Vcc=3.3V Note2 Vcc=5.0V Note2
mVp-p
Vcc=5.0V Note3 VI=0V VI=0V VI=Vcc VI=Vcc Note4 Note5 Note6 Note7
Vcc-dip conditions
VCC
3.0V 2.7V
Vcc-dip condition should also follow The Vcc-turn-on conditions Note2 Note3 Note4 Note5 Note6 Note7 Typical current situation : 16-gray-bar pattern. Vcc=+3.3V/+5.0V CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,R/L,U/D CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB R/L CK,R0~R5,G0~G5,B0~B5,Hsnc,Vsync ENAB,U/D
6-2. Backlight driving The backlight system is an edge-lighting type with twin CCFT (Cold Cathode Fluorescent Tube). The characteristics of single lamp are shown in the following table. Parameter Lamp current Lamp power consumption Lamp frequency Kick-off voltage Symbol IL PL FL Vs Min. 3.5 40 Typ. 6.0 2.8 60 Max. 7.0 70 1000 1300 1450 Unit mArms KHz Vrms Vrms Vrms hour hour Ta=25 Remark Note1 Note2 Note3 Ta=25 Ta =0 Note4 Ta =-10 Note5 IL=6.0mA Note5 IL=7.0mA
Lamp life time Note1
LL LL
50000 30000
Lamp current is measured with current meter for high frequency as shown below.
Note2
At the condition of YL =350cd/m2 beat on the display. Therefore lamp frequency shall be detached as much as possible from the horizontal synchronous frequency and from the harmonics of horizontal synchronous to avoid interference.
Note3 Lamp frequency may produce interference with horizontal synchronous frequency, and this may cause
Note4 The open output voltage of the inverter shall be maintained for more than 1sec; otherwise the lamp may not be turned on. Note5 Since lamp is consumables, the life time written above is referential value and it is not guaranteed in this specification sheet by SHARP. Lamp life time is defined that it applied either or under this condition. (Continuous turning on at Ta=25 , IL=6 or 7mArms) Brightness becomes 50% of the original value under standard condition. Kick-off voltage at Ta= -10 becomes lower. (Continuous operating under for around 1 month under lower temp condition may reduce the brightness to half of the original brightness.) In case of such usage under lower temp environment, periodical lamp exchange is recommended. Note6 The performance of the backlight, for example life time or brightness, is much influenced by the characteristics of the DC-AC inverter for the lamp. When you design or order the inverter, please make sure that a poor lighting caused by the mismatch of the backlight and the inverter (miss-lighting, flicker, etc.) never occur. when you confirm it, the module should be operated in the same condition as it is installed in your instrument. Note7 It is required to have the inverter designed so that to allow the impedance deviation of the two CCFT lamps and the capacity deviation of barast capacitor. exceeds maximum value, 1450 Vrms. In case of operating under lower temp environment, the lamp exhaustion is accelerated and the brightness
7. Timing Characteristics of input signals Timing diagrams of input signal are shown in Fig.2. 7-1. Timing characteristics Parameter Clock Frequency High time Low time Duty ratio Data Horizontal sync. signal Pulse width Vertical Cycle sync. signal Pulse width Horizontal display period Hsync-Clock phase difference Hsync-Vsync phase difference Vertical data start position THp TV TVp THd THc TVh TVs Setup time Hold time Cycle Symbol 1/Tc Tch Tcl Th/T Tds Tdh TH 6 6 40 3 5 20.8 832 2 628 2 800 0 0 23 23 26.4 1056 128 666 4 800 200 798 6 800 Tc-10 TH-THp 23 50 60 Min. Typ. 40.0 Max. 42.0 Unit MHz ns ns % ns ns s clock clock line line clock ns ns line Remark
Note) In case of lower frequency, the deterioration of display quality, flicker etc.,may be occurred. 7-2. Horizontal display position The horizontal display position is determined by ENAB signal and the input data corresponding to the rising edge of ENAB signal is displayed at the left end of the active area. Parameter Enable signal Setup time Pulse width Hsync-Enable signal phase difference symbol Tes Tep THe Min. 5 2 58 800 88 Typ. Max. Tc-10 TH-10 170 Unit ns clock clock Remark
Note) When ENAB is fixed "Low", the display starts from the data of C88(clock) as shown in Fig.2. 7-3. Vertical display position The vertical display position, TVs is fixed "23" (line). 7-4. Input Data Signals and Display Position on the screen
Display position of input data
D1,D H1 D1,DH2 D1,DH 3 D2,DH1 D2,D H2 D 3,DH1 D800,DH1
UP
R
GB
D1,DH600
D 800,D H 600
"
"
8. Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale
Gray Scale
Data signal
R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5
Black Blue Green Cyan Red Magenta Yellow White Black
x
0 0 0 0 1 1 1 1 GS0 GS1 GS2
E E
0 0 0 0 1 1 1 1 0 0 1
0 0 0 0 1 1 1 1 0 0 0
E E
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 0 0 1 1 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
E E
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 0 1 1 0 0 1 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
E E
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 1 0 1 0 1 0 1 0 0 0
0 :Low level voltage, 1 : High level voltage Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit data signals, the 262,144-color display can be achieved on the screen.
Basic Color Gray Scale of Red Gray Scale of Red Gray Scale of Red Gray Scale of Red Gray Scale of Green Gray Scale of Blue Scale
0 1 0
Darker
x O
Brighter
O
GS61 GS62 GS63 GS0 GS1 GS2
E E
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
E E
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
E E
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
E E
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Red Black
x
Darker
x O
Brighter
O
GS61 GS62 GS63 GS0 GS1 GS2
E E
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
E E
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
1 0 1 0 0 0
0 1 1 0 0 0
1 1 1 0 0 0
E E
1 1 1 0 0 0
1 1 1 0 0 0
1 1 1 0 0 0
0 0 0 0 1 0
0 0 0 0 0 1
0 0 0 0 0 0
E E
0 0 0 0 0 0
0 0 0 0 0 0
0 0 0 0 0 0
Green Black
x
Darker
x O
Brighter
O
GS61 GS62 GS63
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
0 0 0
1 0 1
0 1 1
1 1 1
1 1 1
1 1 1
1 1 1
Blue
9. Optical Characteristics Parameter Viewing Angle Range Contrast ratio Horizontal Vertical Symbol 21, 22 11 12 CR =0
Best Viewing
Ta=25 , Vcc=+3.3V or +5V Condition CR 10 Min 60 35 55 150 300 Typ 70 40 70 Max Unit Deg. Deg. Deg. Note2,4 Remark Note1,4
Angle Response Time Rise Decay r d =0 20 40 0.313 0.329 Luminance of white White Unifomity Viewing Angle Horizontal range as a Vertical Brightness Definition 21, 22 50% of the maximum 11 brightness 12 280 350 1.45 35 25 30 Deg. Deg. Deg. cd/m2 Note5 Note1 (Reference value Note4
Note3,4
Chromaticity of White
The measurement shall be executed 30 minutes after lighting at rating. (typical condition:IL=6.0mArms)
The optical characteristics shall be measured in a dark room or equivalent state with the method shown in Fig.3 below.
Note1 Definitions of viewing angle range:
Note2 Definition of contrast ratio: The contrast ratio is defined as the following.
Luminance (brightness) with all pixels white
Contrast Ratio (CR)
Luminance (brightness) with all pixels black
Note3 Definition of response time: The response time is defined as the following figure and shall be measured by switching the input signal for "black" and "white" .
Note4 This shall be measured at center of the screen. Note5 Definition of white uniformity: White uniformity is defined as the following with five measurements (A E).
A D
2 00
4 00
6 00 p ixel
1 50 3 00
C
B
E
4 50 p ixe
Maximum Luminance of five points (brightness) Minimum Luminance of five points (brightness)
10. Display Quantity The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. 11 Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable. b) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. c) Since the front polarizer is easily damaged, pay attention not to scratch it. d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with care. g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth when handling. h) Observe all other precautionary requirements in handling components. i) This module has its circuitry PCBs on the rear side and should be carefully handled in order not to be stressed. j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching protective board over the LCD. Be careful about the optical interface fringe etc. Which degrades display quality. k) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise. l) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to electrical shock. When exchange lamps or service. Turn off the power without tail. m) Be sure not to apply tensile stress to the lamp lead cable. n)Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local ordinances or regulations for disposal.
12.Packing form Piling number of cartons Packing quantity in one carton Carton size [mm] 5 Max 20 494(W)x326(D)x433(H)
Total mass of one carton filled 15.6kg with full modules
13 Reliability test items No. 1 Test item High temperature & high humidity storage test 2 3 4 High temperature storage test Low temperature storage test High temperature & high humidity operation test 5 6 7 High temperature operation test Low temperature operation test Vibration test (non- operating) Conditions Ta= 50 ; 95%RH 240h
(No condensation) Ta= 70 Ta= -35 Ta= 40 240h 240h ; 95%RH 240h
(No condensation) Ta= 65 Ta= -10 240h 240h : 58 500Hz/Gravity:9.8m/s2 Sweep time : 11 minutes Test period : 3 hours (1 hour for each direction of X,Y,Z) Max. gravity : 490m/s2 Pulse width : 11ms, half sine wave Direction : X, Y, Z
Frequency: 10 57Hz/Vibration width (one side):0.075mm
8
Shock test (non- operating)
once for each direction. Result Evaluation Criteria Under the display quality test conditions with normal operation state, these shall be no change which may affect practical display function. 14 Others 1) Lot No Label:
2) Adjusting volume have been set optimally before shipment, so do not change any adjusted value. If adjusted value is changed, the specification may not be satisfied. 3) Disassembling the module can cause permanent damage and should be strictly avoided. 4) Please be careful since image retention may occur when a fixed pattern is displayed for a long time. 5) Do not use LCD module in the atmosphere of corrosive gases, such as sulfide gas or chlorine gases. Polarizer may deteriorated or cause chemical reaction that can lead to short circuits at the terminal Points. Do not use the material, which compounds contain sulfide or chlorine articles in the vicinity of LCD module. At high temperature, these compounds produce corrosive gases. 6) If any problem occurs in relation to the description of this specification , it shall be resolved through discussion with spirit of cooperation.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com
SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com
SINGAPORE
SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com
TAIWAN
KOREA
SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855
SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735

▲Up To Search▲

Price & Availability of LQ104S1DG21

	To Download LQ104S1DG21 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .