View AWT6314R_645788.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AWT6314R
Dual-band CDMA/PCS 3.4 V/28 dBm Linear Power Amplifier Module
PRELIMINARY DATA SHEET - Rev 1.2
FEATURES
* * * * * * * * * Single Mode Operation: POUT +28 dBm High Efficiency: 54 % AMPS, 39 % CDMA Low Quiescent Current: 50 mA 25 % Package Size Reduction Common VMODE Control Line Simplified VCC Bus PCB routing Reduced External Component Count Low Profile Surface Mount Package: 1.1 mm RoHS Compliant Package, 250 oC MSL-3
AW T
631
4
APPLICATIONS
* Dual-band Cellular/PCS CDMA Wireless Handsets
M23 Package 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module
technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, serve to increase handset talk and standby time. The self contained 3 mm x 5 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency and linearity in a 50 system.
GND at slug (pad)
PRODUCT DESCRIPTION
The AWT6314R meets the increasing demands for higher levels of integration in dual-band CDMA/PCS 1X handsets, while reducing board area requirements by 25 %. The package pinout was chosen to enable handset manufacturers to easily route VCC to both power amplifiers and simplify control with a common VMODE pin. The device is manufactured on an advanced InGaP HBT MMIC
VREF_PCS 1
Bias Control
12 RFOUT_PCS
RFIN_PCS 2
11 GND
VCC1 3
10 VCC2
VMODE 4
9
VCC2 A
RFIN_CELL 5
Bias Control
8
RFOUT_CELL
VREF_CELL 6
7
GND
GND
Figure 1: Block Diagram
05/2006
AWT6314R
GND VREF_PCS RFIN_PCS VCC1 VMODE RFIN_CELL VREF_CELL 1 2 3 4 5 6 GND
Figure 2: Pinout
12 11 10 9 8 7
RFOUT_PCS GND VCC2 VCC2A RFOUT_CELL GND
Table 1: Pin Description Table
PIN 1 2 3 4 5 6 7 8 9 10 11 12 NAME VREF_PCS RFIN_PCS V CC1 VMODE RFIN_CELL VREF_CELL GND DESCRIPTION Reference Voltage for PCS Band RF Input for PCS Band Supply Voltage Mode Control Voltage RF Input for Cell Band Reference Voltage for Cell Band Ground
RFOUT_CELL RF Output for Cell Band V C C 2A V CC2 GND Supply Voltage Supply Voltage Ground
RFOUT_PCS RF Output for PCS Band
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
2
AWT6314R
ELECTRICAL CHARACTERISTICS
Table 2: Absolute Minimum and Maximum Ratings PAR AME T E R Supply Voltage (VCC ) Wi th RF Dri ve DC Only Mode Control Voltage (VMODE) Reference Voltage (VREF) RF Input Power (PIN) Storage Temperature (TSTG) MIN 0 0 0 0 -40 M AX +5 +8 +3.5 +3.5 +10 +150 U N IT
V V V dBm C
Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability.
Table 3: Operating Ranges
PARAMETER Operating Frequency (f) Supply Voltage (VCC) Reference Voltage (VREF) Mode Control Voltage (VMODE) RF Output Power (POUT) Case Temperature (TC)
MIN 824 1850 +3.2 +2.75 0 +2.5 0 30.5(1) 27.5(1) -30
TYP +3.4 +2.85 +2.85 31.0 28.0 -
MAX 849 1910 +4.2 +3.1 +0.5 +3.1 +0.5 +85
UNIT MHz V V V dB m C
COMMENTS Cellular PC S
PA "on" PA "shut down" Low Bias Mode High Bias Mode AMPS CDMA
The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB.
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
3
AWT6314R Table 4: Electrical Specifications - AMPS Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, VMODE = 2.85 V, POUT = +31 dBm, 50 system)
PARAMETER Gain Gain Variation Power-Added Efficiency (1) Quiescent Current (Icq) Reference Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance MIN 24 50 TYP 26 0.4 54 50 1.5 <1 -134 -44 -46 MAX 29 1.0 68 3 5 -132 -30 -30 2:1 UNIT dB dB % mA mA A dBm/Hz Low B i as through VREF pin, PA "ON" VCC = +4.3 V, VREF = 0 V, VMODE = 0 V 869 MHz to 894 MHz COMMENTS
dB c
VSWR POUT < +31 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions
Spurious Output Level (all spurious outputs)
-
-
-65
dB c
Load mismatch stress with no permanent degradation or failure
Notes: (1) PAE limit applies at 836.5 MHz.
10:1
-
-
VSWR
4
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
AWT6314R Table 5: Electrical Specifications - Cellular CDMA Operation (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system)
PARAMETER
MIN 25 24 23.5 37 37 8 -
TYP 27.0 26.5 25.5 -50 -50 -49 -62 -60 -65 39 40 9 50 1.5 0.6 <1 -133 -44 -46 -
MAX 30 29 28 -47 -47 -47 -57 -57 -57 68 3 1.0 5 -131 -30 -30 2:1
UNIT
COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V VMODE = +2.85 V, Low Bias through VREF pin, PA "ON" through VMODE pin, VMODE = +2.85 V VCC = +4.3 V, VREF = 0 V, VMODE = 0 V
Gain Adjacent Channel Power at 885 kHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kH Adjacent Channel Power at 1.98 MHz offset (1) Primary Channel BW = 1.23 MHZ Adjacent Channel BW = 30 kHz Power-Added Efficiency (1)
dB
dB c
dB c
%
Quiescent Current (Icq) Reference Current Mode Control Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance
mA mA mA A
dBm/Hz 869 MHz to 894 MHz
dB c
VSWR POUT < +28 dBm In-band Load VSWR < 5:1 Out-of-band Load VSWR < 10:1 Applies over all operating conditions Applies over all operating conditions
Spurious Output Level (all spurious outputs)
-
-
-65
dB c
Load mismatch stress with no permanent degradation or failure
10:1
-
-
VSWR
Notes: (1) PAE and ACP limit applies at 836.5 MHz.
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
5
AWT6314R Table 6: PCS Electrical Specifications (TC = +25 C, VCC = +3.4 V, VREF = +2.85 V, 50 system)
PARAMETER
MIN 24.5 24 23 36 36 7.5 -
TYP 26.5 26.0 25.5 -49 -50 -54 -62 -61 -67 38 39 9 53 2.3 0.6 <1 -133 -47 -55 -
MAX 29 28 27.5 -46.5 -47 -47 -57 -57 -57 70 4 1.0 5 -131 -30 -30 2:1
UNIT
COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V POUT = +28 dBm, VMODE = 0 V POUT = +28 dBm, VMODE = +2.85 V POUT = +16 dBm, VMODE = +2.85 V VMODE = +2.85 V through VREF pin, PA "on" through VMODE pin, VMODE = +2.85 V VCC = +4.3 V, VREF = 0 V, VMODE = 0 V
Gain Adjacent Channel Power at +1.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Adjacent Channel Power at +2.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz Power-Added Efficiency Quiescent Current (Icq) Reference Current Mode Control Current Leakage Current Noise in Receive Band Harmonics 2fo 3fo, 4fo Input Impedance Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure
dB
dB c
dB c
% mA mA mA A
dBm/Hz 1930 MHz to 1990 MHz
dB c VSWR POUT < +28 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges Applies over full operating range
-
-
-65
dB c
8:1
-
-
VSWR
Notes: (1) ACPRs and efficiency limits at mid-band only.
6
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
AWT6314R
APPLICATION INFORMATION
To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications.
Table 7: Bias Control
APPLICATION AMPS CDMA - All power CDMA - All power Shutdown POUT LE V E LS (all) <28 dBm <28 dBm BIAS MODE Low Low High Shutdown V R EF VMODE
+2.85 V +2.85 V +2.85 V +2.85 V +2.85 V 0V 0V 0V
GND at slug (pad)
68 pF
VREF_PCS
0.01 F
1 Bias Control
12
RFIN_PCS
2
11 GND
2.2 F
VCC1
2.2 F 1000 pF
3
10
TRL
Note 1
3.9 nH
VMODE
4
9
1000 pF 68 pF
VCC2
RFIN_CELL
5 Bias Control
8
VREF_CELL
0.01 F
6
7
GND
GND
Note: 1. 3.9 nH Inductor should be rated for >1 Amp.
Figure 3: Application Circuit
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
7
AWT6314R
PACKAGE OUTLINE
Figure 4: Package Outline - 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module
LLLLL
6314R LLLLLNN BBBBCC YYWW
6. Year and Work Week 7. 8.
YY = Year, WW = Work Week
Figure 5: Branding Specification 8
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
AWT6314R
NOTES
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
9
AWT6314R
NOTES
10
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
AWT6314R
NOTES
PRELIMINARY DATA SHEET - Rev 1.2 05/2006
11
AWT6314R
ORDERING INFORMATION
ORDER NUMBER AWT6314RM23Q7 TEMPERATURE RANGE -30 C to +85 C PACKAGE DESCRIPTION RoHS Compliant 12 Pin 3 mm x 5 mm x 1 mm Surface Mount Module COMPONENT PACKAGING
Tape and Reel, 2500 pieces per Reel
ANADIGICS, Inc.
141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE
ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders.
WARNING
ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited.
12
PRELIMINARY DATA SHEET - Rev 1.2 05/2006

▲Up To Search▲

Price & Availability of AWT6314R

	To Download AWT6314R Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .