|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ST7L15, ST7L19 8-bit MCU for automotive with single voltage Flash/ROM memory, data EEPROM, ADC, 5 timers, SPI PRELIMINARY DATA Features Memories - 4 Kbytes single voltage extended Flash (XFlash) or ROM with readout protection, InCircuit programming and In-Application Programming (ICP and IAP), 10K write/erase cycles guaranteed, data retention 20 years at 55C - 256 bytes RAM - 128 bytes data E2PROM with readout protection, 300K write/erase cycles guaranteed, data retention 20 years at 55C Clock, Reset and Supply Management - Enhanced reset system - Enhanced low voltage supervisor (LVD) for main supply - Clock sources: Internal 1% RC oscillator, crystal/ceramic resonator or external clock - Optional x4 or x8 PLL for 4 or 8 MHz internal clock (only x8 PLL available for ROM devices) - 5 power saving modes: Halt, Active Halt, Auto Wake-Up from Halt, Wait and Slow I/O Ports - Up to 17 multifunctional bidirectional I/O lines - 7 high sink outputs 5 Timers - Configurable watchdog timer - Two 8-bit Lite timers with prescaler, 1 realtime base and 1 input capture - Two 12-bit autoreload timers with 4 PWM outputs, 1 input capture, 1 pulse and 4 output compare functions SO20 300mil Communication Interface - SPI synchronous serial interface Interrupt Management - 12 interrupt vectors plus TRAP and RESET - 15 external interrupt lines (on 4 vectors) A/D Converter - 7 input channels - 10-bit precision Instruction Set - 8-bit data manipulation - 63 basic instructions with illegal opcode detection - 17 main addressing modes - 8 x 8 unsigned multiply instructions Development Tools - Full hardware/software development package - DM (Debug Module) Device Summary Features Program Memory - bytes RAM (stack) - bytes Data EEPROM - bytes Peripherals Operating Supply CPU Frequency Operating Temperature Packages ST7L15 4K 256 (128) 128 Lite Timer with Watchdog, Autoreload Timer, SPI, 10-bit ADC 3V to 5.5V Up to 8 MHz (w/ext OSC up to 16 MHz and int 1 MHz RC 1%, PLLx8/4 MHz) Up to -40 to +85C / -40 to +125C SO20 300mil ST7L19 Rev. 3 January 2007 1/138 This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice. 1 Table of Contents 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.2 PARAMETRIC DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 DEBUG MODULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 PIN DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 REGISTER AND MEMORY MAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 FLASH PROGRAM MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.3 PROGRAMMING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.4 ICC INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.5 MEMORY PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.6 RELATED DOCUMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.7 REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 DATA EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5.3 MEMORY ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.4 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.5 ACCESS ERROR HANDLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.6 DATA EEPROM READOUT PROTECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5.7 REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 CENTRAL PROCESSING UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.3 CPU REGISTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7 SUPPLY, RESET AND CLOCK MANAGEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.1 INTERNAL RC OSCILLATOR ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 7.2 PHASE LOCKED LOOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.3 REGISTER DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7.4 MULTI-OSCILLATOR (MO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 7.5 RESET SEQUENCE MANAGER (RSM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 7.6 SYSTEM INTEGRITY MANAGEMENT (SI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 8 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8.1 NON MASKABLE SOFTWARE INTERRUPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8.2 EXTERNAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 8.3 PERIPHERAL INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 9 POWER SAVING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9.2 SLOW MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 9.3 WAIT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 9.4 HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 9.5 ACTIVE HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138. 38 ... 9.6 AUTO WAKE-UP FROM HALT MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 10 I/O PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 2/138 1 Table of Contents 10.1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 10.2 FUNCTIONAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 10.3 I/O PORT IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10.4 UNUSED I/O PINS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10.5 LOW-POWER MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10.6 INTERRUPTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 10.7 DEVICE-SPECIFIC I/O PORT CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 10.8 MULTIPLEXED INPUT/OUTPUT PORTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 11 ON-CHIP PERIPHERALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 11.1 WATCHDOG TIMER (WDG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 11.2 DUAL 12-BIT AUTORELOAD TIMER 4 (AT4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 11.3 LITE TIMER 2 (LT2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 11.4 SERIAL PERIPHERAL INTERFACE (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 11.5 10-BIT A/D CONVERTER (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 12 INSTRUCTION SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 12.1 ST7 ADDRESSING MODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 12.2 INSTRUCTION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 13 ELECTRICAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13.1 PARAMETER CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 13.2 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 13.3 OPERATING CONDITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 13.4 SUPPLY CURRENT CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 13.5 CLOCK AND TIMING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 13.6 MEMORY CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 13.7 EMC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 13.8 I/O PORT PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 13.9 CONTROL PIN CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 13.10 COMMUNICATION INTERFACE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . 120 13.11 10-BIT ADC CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 14 PACKAGE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 14.1 PACKAGE MECHANICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 14.2 SOLDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 15 DEVICE CONFIGURATION AND ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . 126 15.1 OPTION BYTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 15.2 DEVICE ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 15.3 DEVELOPMENT TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 15.4 ST7 APPLICATION NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 16 REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 3/138 ST7L15, ST7L19 1 INTRODUCTION 1.1 DESCRIPTION The ST7L1x is a member of the ST7 microcontroller family suitable for automotive applications. All ST7 devices are based on a common industrystandard 8-bit core, featuring an enhanced instruction set. The ST7L1 features Flash memory with byte-bybyte In-Circuit Programming (ICP) and In-Application Programming (IAP) capability. Under software control, the ST7L1 device can be placed in WAIT, SLOW or HALT mode, reducing power consumption when the application is in idle or standby state. The enhanced instruction set and addressing modes of the ST7 offer both power and flexibility to software developers, enabling the design of highly efficient and compact application code. In addition Figure 1. General Block Diagram Int. 1% RC 1 MHz to standard 8-bit data management, all ST7 microcontrollers feature true bit manipulation, 8x8 unsigned multiplication and indirect addressing modes. 1.2 PARAMETRIC DATA For easy reference, all parametric data is located in section 13 on page 98. 1.3 DEBUG MODULE The ST7L1 features an on-chip Debug Module (DM) to support In-Circuit Debugging (ICD). For a description of the DM registers, refer to the ST7 ICC Protocol Reference Manual. PLL x8 or PLL x4* CLKIN /2 OSC1 OSC2 Ext. OSC 1 MHz to 16 MHz 12-bit AUTORELOAD TIMER 4 8-bit LITE TIMER 2 INTERNAL CLOCK LVD ADDRESS AND DATA BUS PORT A PORT B PORT C* VDD VSS RESET POWER SUPPLY CONTROL 8-bit CORE ALU PA7:0 (8 bits) PB6:0 (7 bits) PC1:0 (2 bits) ADC SPI PROGRAM MEMORY (up to 4 Kbytes) DEBUG MODULE RAM (256 bytes) DATA EEPROM (128 bytes) WATCHDOG *Note: Not available on ROM devices. 4/138 1 ST7L15, ST7L19 2 PIN DESCRIPTION Figure 2. 20-Pin SO Package Pinout VSS VDD RESET SS/AIN0/PB0 SCK/AIN1/PB1 MISO/AIN2/PB2 MOSI/AIN3/PB3 CLKIN/AIN4/PB4 AIN5/PB5 AIN6/PB6 1 2 3 4 5 6 7 8 9 10 ei2 ei1 ei3 ei0 20 19 18 17 16 15 14 13 12 11 OSC1/CLKIN/PC02) OSC2/PC12) PA0 (HS)/LTIC1) PA1 (HS)/ATIC PA2 (HS)/ATPWM0 PA3 (HS)/ATPWM1 PA4 (HS)/ATPWM2 PA5 (HS)/ATPWM3/ICCDATA PA6/MCO/ICCCLK/BREAK PA7 (HS) (HS) 20mA High sink capability eix associated external interrupt vector Notes: 1. This pin cannot be configured as external interrupt in ROM devices. 2. OSC1 and OSC2 are not multiplexed in ROM devices and Port C is not present. Legend / Abbreviations for Table 1: Type: I = input, O = output, S = supply In/Output level: CT = CMOS 0.3VDD / 0.7VDD with input trigger Output level: HS = 20mA high sink (on N-buffer only) Port and control configuration: - Input: float = floating, wpu = weak pull-up, int = interrupt, ana = analog - Output: OD = open drain, PP = push-pull The RESET configuration of each pin (shown in bold) is valid as long as the device is in reset state. Table 1. Device Pin Description Pin No. Type Pin Name SO20 1 2 3 VSS VDD RESET Level Output Input Port / Control Input float wpu ana int Output OD PP Main Function (after reset) Ground Main power supply X X Top priority non maskable interrupt (active low) Alternate Function S S I/O CT 5/138 1 ST7L15, ST7L19 Pin No. Type Pin Name SO20 Level Output Input Port / Control Input float wpu ana int Output OD PP Main Function (after reset) Alternate Function 4 PB0/AIN0/SS I/O CT X ei3 X X X Port B0 5 6 7 81) 91) 10 1) PB1/AIN1/SCK PB2/AIN2/MISO PB3/AIN3/MOSI PB4/AIN4/CLKIN/ COMPINPB5/AIN5 PB6/AIN6 PA7 I/O I/O I/O I/O I/O I/O CT CT CT CT CT CT X X X X X X ei1 ei2 X X X X X X X X X X X X X X X X X X X X Port B1 Port B2 Port B3 Port B4 Port B5 Port B6 Port A7 ADC Analog Input 0 or SPI Slave Select (active low) Caution: No negative current injection allowed on this pin. ADC Analog Input 1 or SPI Serial Clock ADC Analog Input 2 or SPI Master In/ Slave Out Data ADC Analog Input 3 or SPI Master Out / Slave In Data ADC Analog Input 4 or External clock input ADC Analog Input 5 ADC Analog Input 6 111) I/O CT HS X Main Clock Output or In-Circuit Communication Clock or External BREAK Caution: During normal operation this pin must be pulled- up, internally or externally (external pull-up of 10k mandatory in noisy environment). This is to avoid entering ICC mode unexpectedly during a reset. In the application, even if the pin is configured as output, any reset puts it back in input pull-up In-Circuit Communication Data or Autoreload Timer PWM3 Autoreload Timer PWM2 Autoreload Timer PWM1 Autoreload Timer PWM0 Autoreload Timer Input Capture Lite Timer Input Capture Resonator oscillator inverter output Resonator oscillator inverter input or External clock input 12 PA6 /MCO/ ICCCLK/BREAK I/O CT X ei1 X X Port A6 13 14 15 16 17 18 1) PA5 /ICCDATA/ ATPWM3 PA4/ATPWM2 PA3/ATPWM1 PA2/ATPWM0 PA1/ATIC PA0/LTIC OSC2/PC1 I/O CT HS X I/O CT HS X I/O CT HS X I/O CT HS X I/O CT HS X I/O CT HS X I/O X X X ei1 X X X ei0 X X X X X X X X X X Port A5 Port A4 Port A3 Port A2 Port A1 Port A0 Port C13) 192) 202) OSC1/CLKIN/PC0 I/O Port C03) Notes: 1. This pin cannot be configured as external interrupt in ROM devices. 2. OSC1 and OSC2 are not multiplexed in ROM devices and Port C is not present. 3. PCOR not implemented but p-transistor always active in output mode (refer to Figure 29 on page 45) 6/138 1 ST7L15, ST7L19 3 REGISTER AND MEMORY MAP As shown in Figure 3, the MCU can address 64 Kbytes of memories and I/O registers. The available memory locations consist of 128 bytes of register locations, 256 bytes of RAM, 128 bytes of data EEPROM and up to 4 Kbytes of Flash program memory. The RAM space includes up to 128 bytes for the stack from 180h to 1FFh. The highest address bytes contain the user reset and interrupt vectors. The Flash memory contains two sectors (see Figure 3) mapped in the upper part of the ST7 adFigure 3. Memory Map 0000h 007Fh 0080h 00FFh 0100h 017Fh 0180h dressing space so the reset and interrupt vectors are located in Sector 0 (F000h-FFFFh). The size of Flash Sector 0 and other device options are configurable by Option byte (refer to section 15.1 on page 126). IMPORTANT: Memory locations marked as "Reserved" must never be accessed. Accessing a reserved area can have unpredictable effects on the device. HW Registers (see Table 2) RAM (128 bytes) Reserved RAM (128 bytes) Reserved 0080h Short Addressing RAM (zero page) 00FFh 0100h 017Fh 0180h 01FFh Reserved DEE0h 128 bytes Stack DEE1h DEE2h RCCRH0 RCCRL0 RCCRH1 01FFh 0200h DEE3h RCCRL1 See section 7.1 on page 21 and note 1. 0FFFh 1000h Data EEPROM (128 bytes) 107Fh 1080h Reserved EFFFh F000h 4K FLASH PROGRAM MEMORY Flash Memory (4K) FFDFh FFE0h F000h FBFFh FC00h FFFFh 3 Kbytes (SECTOR 1) 1 Kbyte (SECTOR 0) Interrupt and Reset Vectors (see Table 5) FFFFh Notes: 1. DEE0h, DEE1h, DEE2h and DEE3h addresses are located in a reserved area but are special bytes containing also the RC calibration values which are read-accessible only in user mode. If all the EEPROM data or Flash space (including the RC calibration values locations) has been erased (after the readout protection removal), then the RC calibration values can still be obtained through these four addresses. 7/138 1 ST7L15, ST7L19 REGISTER AND MEMORY MAP (cont'd) Table 2. Hardware Register Map Address 0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh 0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h to 002Dh 002Eh 0002Fh 00030h WDG FLASH EEPROM WDGCR FCSR EECSR Block Register Label PADR PADDR PAOR PBDR PBDDR PBOR PCDR PCDDR LTCSR2 LTARR LTCNTR LTCSR1 LTICR ATCSR CNTR1H CNTR1L ATRH ATRL PWMCR PWM0CSR PWM1CSR PWM2CSR PWM3CSR DCR0H DCR0L DCR1H DCR1L DCR2H DCR2L DCR3H DCR3L ATICRH ATICRL ATCSR2 BREAKCR ATR2H ATR2L DTGR BREAKEN Register Name Port A Data Register Port A Data Direction Register Port A Option Register Port B Data Register Port B Data Direction Register Port B Option Register Port C Data Register Port C Data Direction Register Lite Timer Control/Status Register 2 Lite Timer Autoreload Register Lite Timer Counter Register Lite Timer Control/Status Register 1 Lite Timer Input Capture Register Timer Control/Status Register Counter Register 1 High Counter Register 1 Low Autoreload Register High Autoreload Register Low PWM Output Control Register PWM 0 Control/Status Register PWM 1 Control/Status Register PWM 2 Control/Status Register PWM 3 Control/Status Register PWM 0 Duty Cycle Register High PWM 0 Duty Cycle Register Low PWM 1 Duty Cycle Register High PWM 1 Duty Cycle Register Low PWM 2 Duty Cycle Register High PWM 2 Duty Cycle Register Low PWM 3 Duty Cycle Register High PWM 3 Duty Cycle Register Low Input Capture Register High Input Capture Register Low Timer Control/Status Register 2 Break Control Register Autoreload Register 2 High Autoreload Register 2 Low Dead Time Generation Register Break Enable Register Reserved area (7 bytes) Watchdog Control Register Flash Control/Status Register Data EEPROM Control/Status Register 7Fh 00h 00h R/W R/W R/W Reset Status FFh1) 00h 40h FFh1) 00h 00h 0xh 00h 00h 00h 00h 0x00 0000b xxh 0x00 0000b 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 03h 00h 00h 00h 00h 03h Remarks R/W R/W R/W R/W R/W R/W2) R/W R/W R/W R/W Read Only R/W Read Only R/W Read Only Read Only R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Read Only Read Only R/W R/W R/W R/W R/W R/W Port A Port B Port C LITE TIMER 2 AUTORELOAD TIMER 4 8/138 1 ST7L15, ST7L19 Address 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah 003Bh 003Ch 003Dh to 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh 0050h 0051h 0052h to 007Fh Block Register Label SPIDR SPICR SPICSR ADCCSR ADCDRH ADCDRL EICR MCCSR RCCR SICSR PLLTST EISR Register Name SPI Data I/O Register SPI Control Register SPI Control Status Register A/D Control Status Register A/D Data Register High Data Low Register External Interrupt Control Register Main Clock Control/Status Register RC oscillator Control Register System Integrity Control/Status Register PLL test register External Interrupt Selection Register Reserved area (12 bytes) Reset Status xxh 0xh 00h 00h xxh 0xh 00h 00h FFh 0110 0xx0b 00h 0Ch Remarks R/W R/W R/W R/W Read Only R/W R/W R/W R/W R/W R/W R/W SPI ADC ITC MCC Clock and Reset PLL clock select ITC AWU AWUPR AWUCSR DMCR DMSR DMBK1H DMBK1L DMBK2H DMBK2L DMCR2 AWU Prescaler Register AWU Control/Status Register DM Control Register DM Status Register DM Breakpoint Register 1 High DM Breakpoint Register 1 Low DM Breakpoint Register 2 High DM Breakpoint Register 2 Low DM Control Register 2 Reserved area (46 bytes) FFh 00h 00h 00h 00h 00h 00h 00h 00h R/W R/W R/W R/W R/W R/W R/W R/W R/W DM3) Legend: x = undefined, R/W = read/write Notes: 1. The contents of the I/O port DR registers are readable only in output configuration. In input configuration, the values of the I/O pins are returned instead of the DR register contents. 2. The bits associated with unavailable pins must always keep their reset value. 3. For a description of the Debug Module registers, see ST7 ICC Protocol Reference Manual. 9/138 1 ST7L15, ST7L19 4 FLASH PROGRAM MEMORY 4.1 INTRODUCTION The ST7 single voltage extended Flash (XFlash) is a non-volatile memory that can be electrically erased and programmed either on a byte-by-byte basis or up to 32 bytes in parallel. The XFlash devices can be programmed off-board (plugged in a programming tool) or on-board using In-Circuit Programming or In-Application Programming. The array matrix organization allows each sector to be erased and reprogrammed without affecting other sectors. 4.2 MAIN FEATURES ICP (In-Circuit Programming) IAP (In-Application Programming) ICT (In-Circuit Testing) for downloading and executing user application test patterns in RAM Sector 0 size configurable by option byte Readout and write protection 4.3 PROGRAMMING MODES The ST7 can be programmed in three different ways: - Insertion in a programming tool. In this mode, Flash sectors 0 and 1, option byte row and data EEPROM (if present) can be programmed or erased. - In-Circuit Programming. In this mode, Flash sectors 0 and 1, option byte row and data EEPROM (if present) can be programmed or erased without removing the device from the application board. - In-Application Programming. In this mode, sector 1 and data EEPROM (if present) can be programmed or erased without removing the device from the application board and while the application is running. 4.3.1 In-Circuit Programming (ICP) ICP uses a protocol called ICC (In-Circuit Communication) which allows an ST7 plugged on a printed circuit board (PCB) to communicate with an external programming device connected via a cable. ICP is performed in three steps: - Switch the ST7 to ICC mode (In-Circuit Communications). This is done by driving a specific signal sequence on the ICCCLK/DATA pins while the RESET pin is pulled low. When the ST7 enters ICC mode, it fetches a specific RESET vector which points to the ST7 System Memory containing the ICC protocol routine. This routine enables the ST7 to receive bytes from the ICC interface. - Download ICP Driver code in RAM from the ICCDATA pin - Execute ICP Driver code in RAM to program the Flash memory Depending on the ICP Driver code downloaded in RAM, Flash memory programming can be fully customized (number of bytes to program, program locations, or selection of the serial communication interface for downloading). 4.3.2 In-Application Programming (IAP) This mode uses an IAP Driver program previously programmed in Sector 0 by the user (in ICP mode). IAP mode is fully controlled by user software, allowing it to be adapted to the user application (such as a user-defined strategy for entering programming mode or a choice of communications protocol used to fetch the data to be stored). This mode can be used to program any memory areas except Sector 0, which is write/erase protected to allow recovery in case errors occur during the programming operation. 10/138 1 ST7L15, ST7L19 FLASH PROGRAM MEMORY (cont'd) 4.4 ICC INTERFACE ICP needs a minimum of four and up to six pins to be connected to the programming tool. These pins are: - RESET: Device reset - VSS: Device power supply ground Figure 4. Typical ICC Interface PROGRAMMING TOOL ICC CONNECTOR ICC Cable ICC CONNECTOR HE10 CONNECTOR TYPE OPTIONAL (See Note 4) APPLICATION BOARD - ICCCLK: ICC output serial clock pin - ICCDATA: ICC input serial data pin - OSC1: Main clock input for external source (not required on devices without OSC1/OSC2 pins) - VDD: Application board power supply (optional, see Note 3) (See Note 3) 9 10 7 8 5 6 3 4 1 2 APPLICATION RESET SOURCE See Note 2 APPLICATION POWER SUPPLY CL2 CL1 See Note 1 and Caution APPLICATION I/O See Note 1 ICCCLK RESET ICCDATA VDD OSC2 OSC1 ST7 Notes: 1. If the ICCCLK or ICCDATA pins are only used as outputs in the application, no signal isolation is necessary. As soon as the Programming Tool is plugged to the board, even if an ICC session is not in progress, the ICCCLK and ICCDATA pins are not available for the application. If they are used as inputs by the application, isolation such as a serial resistor must be implemented in case another device forces the signal. Refer to the Programming Tool documentation for recommended resistor values. 2. During the ICP session, the programming tool must control the RESET pin. This can lead to conflicts between the programming tool and the application reset circuit if it drives more than 5mA at high level (push-pull output or pull-up resistor < 1K). A schottky diode can be used to isolate the application RESET circuit in this case. When using a classical RC network with R > 1K or a reset management IC with open drain output and pull-up resistor > 1K, no additional components are needed. In all cases the user must ensure that no external reset is generated by the application during the ICC session. 3. The use of pin 7 of the ICC connector depends on the Programming Tool architecture. This pin must be connected when using most ST Programming Tools (it is used to monitor the application power supply). Please refer to the Programming Tool Manual. 4. Pin 9 must be connected to the OSC1 pin of the ST7 when the clock is not available in the application or if the selected clock option is not programmed in the option byte. On ST7 devices with multi-oscillator capability, OSC2 must be grounded in this case. 5. In 38-pulse ICC mode, the internal RC oscillator is forced as a clock source, regardless of the selection in the option byte. For ST7L1 devices which do not support the internal RC oscillator, the "option byte disabled" mode must be used (35-pulse ICC mode entry, clock provided by the tool). Caution: During normal operation the ICCCLK pin must be pulled up, internally or externally (external pull-up of 10k mandatory in noisy environment). This is to avoid entering ICC mode unexpectedly during a reset. In the application, even if the pin is configured as output, any reset puts it back in input pull-up. 11/138 1 ST7L15, ST7L19 FLASH PROGRAM MEMORY (cont'd) 4.5 MEMORY PROTECTION There are two different types of memory protection: Readout Protection and Write/Erase Protection, which can be applied individually. 4.5.1 Readout Protection Readout protection, when selected, protects against program memory content extraction and against write access to Flash memory. Even if no protection can be considered as totally unbreakable, the feature provides a very high level of protection for a general purpose microcontroller. Both program and data E2 memory are protected. In Flash devices, this protection is removed by reprogramming the option. In this case, both program and data E2 memory are automatically erased and the device can be reprogrammed. Readout protection selection depends on the device type: - In Flash devices it is enabled and removed through the FMP_R bit in the option byte. - In ROM devices it is enabled by the mask option specified in the Option List. 4.5.2 Flash Write/Erase Protection Write/erase protection, when set, makes it impossible to both overwrite and erase program memory. It does not apply to E2 data. Its purpose is to provide advanced security to applications and prevent any change being made to the memory content. Warning: Once set, Write/erase protection can never be removed. A write-protected Flash device is no longer reprogrammable. Write/erase protection is enabled through the FMP_W bit in the option byte. 4.6 RELATED DOCUMENTATION For details on Flash programming and ICC protocol, refer to the ST7 Flash Programming Reference Manual and to the ST7 ICC Protocol Reference Manual. 4.7 REGISTER DESCRIPTION FLASH CONTROL/STATUS REGISTER (FCSR) Read/Write Reset Value: 000 0000 (00h) 1st RASS Key: 0101 0110 (56h) 2nd RASS Key: 1010 1110 (AEh) 7 0 0 0 0 0 OPT LAT 0 PGM Note: This register is reserved for programming using ICP, IAP or other programming methods. It controls the XFlash programming and erasing operations. When an EPB or another programming tool is used (in socket or ICP mode), the RASS keys are sent automatically. 12/138 1 ST7L15, ST7L19 5 DATA EEPROM 5.1 INTRODUCTION The Electrically Erasable Programmable Read Only Memory can be used as a non volatile backup for storing data. Using the EEPROM requires a basic access protocol described in this chapter. 5.2 MAIN FEATURES Up to 32 bytes programmed in the same cycle EEPROM mono-voltage (charge pump) Chained erase and programming cycles Internal control of the global programming cycle duration WAIT mode management Readout protection Figure 5. EEPROM Block Diagram HIGH VOLTAGE PUMP EECSR 0 0 0 0 0 0 E2LAT E2PGM ADDRESS DECODER 4 ROW DECODER EEPROM MEMORY MATRIX (1 ROW = 32 x 8 BITS) 128 DATA MULTIPLEXER 4 128 32 x 8 BITS DATA LATCHES 4 ADDRESS BUS DATA BUS 13/138 1 ST7L15, ST7L19 DATA EEPROM (cont'd) 5.3 MEMORY ACCESS The Data EEPROM memory read/write access modes are controlled by the E2LAT bit of the EEPROM Control/Status register (EECSR). The flowchart in Figure 6 describes these different memory access modes. Read Operation (E2LAT = 0) The EEPROM can be read as a normal ROM location when the E2LAT bit of the EECSR register is cleared. On this device, Data EEPROM can also be used to execute machine code. Do not write to the Data EEPROM while executing from it. This would result in an unexpected code being executed. Write Operation (E2LAT = 1) To access the write mode, the E2LAT bit must be set by software (the E2PGM bit remains cleared). When a write access to the EEPROM area occurs, the value is latched inside the 32 data latches according to its address. When PGM bit is set by the software, all the previous bytes written in the data latches (up to 32) are programmed in the EEPROM cells. The effective high address (row) is determined by the last EEPROM write sequence. To avoid wrong programming, the user must ensure that all the bytes written between two programming sequences have the same high address: Only the five Least Significant Bits of the address can change. At the end of the programming cycle, the PGM and LAT bits are cleared simultaneously. Note: Care should be taken during the programming cycle. Writing to the same memory location over-programs the memory (logical AND between the two write access data results) because the data latches are only cleared at the end of the programming cycle and by the falling edge of the E2LAT bit. It is not possible to read the latched data. This note is illustrated by the Figure 8 on page 16. Figure 6. Data EEPROM Programming Flowchart READ MODE E2LAT = 0 E2PGM = 0 WRITE MODE E2LAT = 1 E2PGM = 0 READ BYTES IN EEPROM AREA WRITE UP TO 32 BYTES IN EEPROM AREA (with the same 11 MSB of the address) START PROGRAMMING CYCLE E2LAT = 1 E2PGM = 1 (set by software) 0 CLEARED BY HARDWARE E2LAT 1 14/138 1 ST7L15, ST7L19 DATA EEPROM (cont'd) Figure 7. Data EEPROM Write Operation Row / Byte ROW DEFINITION 0 1 ... N Read operation impossible 0 1 2 3 ... 30 31 Physical Address 00h...1Fh 20h...3Fh Nx20h...Nx20h+1Fh Read operation possible Byte 1 Byte 2 PHASE 1 Byte 32 Programming cycle PHASE 2 Writing data latches E2LAT bit Set by USER application Waiting E2PGM and E2LAT to fall Cleared by hardware E2PGM bit Note: If a programming cycle is interrupted (by a reset action), the integrity of the data in memory is not guaranteed. 15/138 1 ST7L15, ST7L19 DATA EEPROM (cont'd) 5.4 POWER SAVING MODES Wait mode The data EEPROM can enter WAIT mode on execution of the WFI instruction of the microcontroller or when the microcontroller enters ACTIVE HALT mode.The data EEPROM immediately enters this mode if there is no programming in progress, otherwise the data EEPROM finishes the cycle and then enters WAIT mode. Active Halt mode Refer to WAIT mode. Halt mode The data EEPROM immediately enters HALT mode if the microcontroller executes the HALT instruction. Therefore, the EEPROM stops the function in progress, and data may be corrupted. 5.5 ACCESS ERROR HANDLING If a read access occurs while E2LAT = 1, then the data bus is not driven. If a write access occurs while E2LAT = 0, then the data on the bus is not latched. If a programming cycle is interrupted (by RESET action), the integrity of the data in memory is not guaranteed. 5.6 DATA EEPROM READOUT PROTECTION The readout protection is enabled through an option bit (see option byte section). When this option is selected, the programs and data stored in the EEPROM memory are protected against readout (including a rewrite protection). In Flash devices, when this protection is removed by reprogramming the Option Byte, the entire Program memory and EEPROM is first automatically erased. Note: Both Program Memory and data EEPROM are protected using the same option bit. Figure 8. Data EEPROM Programming Cycle READ OPERATION NOT POSSIBLE INTERNAL PROGRAMMING VOLTAGE ERASE CYCLE WRITE OF DATA LATCHES WRITE CYCLE READ OPERATION POSSIBLE tPROG LAT PGM 16/138 1 ST7L15, ST7L19 DATA EEPROM (cont'd) 5.7 REGISTER DESCRIPTION EEPROM CONTROL/STATUS REGISTER (EECSR) Read/Write Reset Value: 0000 0000 (00h) 7 0 0 0 0 0 0 0 E2LAT E2PGM Bits 7:2 = Reserved, forced by hardware to 0. Bit 1 = E2LAT Latch Access Transfer This bit is set by software. It is cleared by hardware at the end of the programming cycle. It can only be cleared by software if the E2PGM bit is cleared. 0: Read mode 1: Write mode Bit 0 = E2PGM Programming control and status This bit is set by software to begin the programming cycle. At the end of the programming cycle, this bit is cleared by hardware. 0: Programming finished or not yet started 1: Programming cycle is in progress Note: If the E2PGM bit is cleared during the programming cycle, the memory data is not guaranteed Table 3. Data EEPROM Register Map and Reset Values Address (Hex.) 0030h Register Label EECSR Reset Value 7 6 5 4 3 2 1 E2LAT 0 0 E2PGM 0 0 0 0 0 0 0 17/138 1 ST7L15, ST7L19 6 CENTRAL PROCESSING UNIT 6.1 INTRODUCTION This CPU has a full 8-bit architecture and contains six internal registers allowing efficient 8-bit data manipulation. 6.2 MAIN FEATURES 63 basic instructions Fast 8-bit by 8-bit multiply 17 main addressing modes Two 8-bit index registers 16-bit stack pointer Low power modes Maskable hardware interrupts Non-maskable software interrupt 6.3 CPU REGISTERS The six CPU registers shown in Figure 9 are not present in the memory mapping and are accessed by specific instructions. Figure 9. CPU Registers 7 RESET VALUE = XXh 7 RESET VALUE = XXh 7 RESET VALUE = XXh 15 PCH 87 PCL 0 0 0 0 Accumulator (A) The Accumulator is an 8-bit general purpose register used to hold operands and the results of the arithmetic and logic calculations and to manipulate data. Index Registers (X and Y) In indexed addressing modes, these 8-bit registers are used to create either effective addresses or temporary storage areas for data manipulation. (The Cross-Assembler generates a precede instruction (PRE) to indicate that the following instruction refers to the Y register.) The Y register is not affected by the interrupt automatic procedures (not pushed to and popped from the stack). Program Counter (PC) The program counter is a 16-bit register containing the address of the next instruction to be executed by the CPU. It is made of two 8-bit registers PCL (Program Counter Low which is the LSB) and PCH (Program Counter High which is the MSB). ACCUMULATOR X INDEX REGISTER Y INDEX REGISTER PROGRAM COUNTER RESET VALUE = RESET VECTOR @ FFFEh-FFFFh 7 111HI 0 NZC CONDITION CODE REGISTER RESET VALUE = 1 1 1 X 1 X X X 15 87 0 STACK POINTER RESET VALUE = STACK HIGHER ADDRESS X = Undefined Value 18/138 1 ST7L15, ST7L19 CPU REGISTERS (cont'd) CONDITION CODE REGISTER (CC) Read/Write Reset Value: 111x1xxx 7 1 1 1 H I N Z 0 C because the I bit is set by hardware at the start of the routine and reset by the IRET instruction at the end of the routine. If the I bit is cleared by software in the interrupt routine, pending interrupts are serviced regardless of the priority level of the current interrupt routine. Bit 2 = N Negative This bit is set and cleared by hardware. It is representative of the result sign of the last arithmetic, logical or data manipulation. It is a copy of the 7th bit of the result. 0: The result of the last operation is positive or null. 1: The result of the last operation is negative (that is, the most significant bit is a logic 1). This bit is accessed by the JRMI and JRPL instructions. Bit 1 = Z Zero This bit is set and cleared by hardware. This bit indicates that the result of the last arithmetic, logical or data manipulation is zero. 0: The result of the last operation is different from zero. 1: The result of the last operation is zero. This bit is accessed by the JREQ and JRNE test instructions. The 8-bit Condition Code register contains the interrupt mask and four flags representative of the result of the instruction just executed. This register can also be handled by the PUSH and POP instructions. These bits can be individually tested and/or controlled by specific instructions. Bit 4 = H Half carry This bit is set by hardware when a carry occurs between bits 3 and 4 of the ALU during an ADD or ADC instruction. It is reset by hardware during the same instructions. 0: No half carry has occurred. 1: A half carry has occurred. This bit is tested using the JRH or JRNH instruction. The H bit is useful in BCD arithmetic subroutines. Bit 3 = I Interrupt mask This bit is set by hardware when entering in interrupt or by software to disable all interrupts except the TRAP software interrupt. This bit is cleared by software. 0: Interrupts are enabled. 1: Interrupts are disabled. This bit is controlled by the RIM, SIM and IRET instructions and is tested by the JRM and JRNM instructions. Note: Interrupts requested while I is set are latched and can be processed when I is cleared. By default an interrupt routine is not interruptible Bit 0 = C Carry/borrow This bit is set and cleared by hardware and software. It indicates an overflow or an underflow has occurred during the last arithmetic operation. 0: No overflow or underflow has occurred. 1: An overflow or underflow has occurred. This bit is driven by the SCF and RCF instructions and tested by the JRC and JRNC instructions. It is also affected by the "bit test and branch", shift and rotate instructions. 19/138 1 ST7L15, ST7L19 CPU REGISTERS (cont'd) STACK POINTER (SP) Read/Write Reset Value: 01FFh 15 0 7 1 SP6 SP5 SP4 SP3 SP2 SP1 0 0 0 0 0 0 8 1 0 SP0 The Stack Pointer is a 16-bit register which always points to the next free location in the stack. It is then decremented after data has been pushed onto the stack and incremented before data is popped from the stack (see Figure 10). Since the stack is 128 bytes deep, the 9 most significant bits are forced by hardware. Following an MCU Reset, or after a Reset Stack Pointer instruction (RSP), the Stack Pointer contains its reset value (the SP6 to SP0 bits are set) which is the stack higher address. The least significant byte of the Stack Pointer (called S) can be directly accessed by an LD instruction. Figure 10. Stack Manipulation Example CALL Subroutine @ 0180h Interrupt Event PUSH Y Note: When the lower limit is exceeded, the Stack Pointer wraps around to the stack upper limit, without indicating the stack overflow. The previously stored information is then overwritten and therefore lost. The stack also wraps in case of an underflow. The stack is used to save the return address during a subroutine call and the CPU context during an interrupt. The user may also directly manipulate the stack by means of the PUSH and POP instructions. In the case of an interrupt, the PCL is stored at the first location pointed to by the SP. Then the other registers are stored in the next locations as shown in Figure 10. - When an interrupt is received, the SP is decremented and the context is pushed on the stack. - On return from interrupt, the SP is incremented and the context is popped from the stack. A subroutine call occupies two locations and an interrupt occupies five locations in the stack area. POP Y IRET RET or RSP SP SP CC A X PCH SP PCH @ 01FFh PCL PCL PCH PCL Y CC A X PCH PCL PCH PCL SP CC A X PCH PCL PCH PCL SP PCH PCL SP Stack Higher Address = 01FFh Stack Lower Address = 0180h 20/138 1 ST7L15, ST7L19 7 SUPPLY, RESET AND CLOCK MANAGEMENT The device includes a range of utility features for securing the application in critical situations (for example, in case of a power brown-out) and reducing the number of external components. Main features RCCR RCCRH0 RCCRL0 RCCRH1 RCCRL1 Conditions VDD = 5V TA = 25C fRC = 1 MHz VDD = 3.3V TA = 25C fRC = 1 MHz ST7L1 Address DEE0h1) (CR[9:2]) DEE1h1) (CR[1:0]) DEE2h1) (CR[9:2]) DEE3h1) (CR[1:0]) Clock Management - 1 MHz internal RC oscillator (enabled by option byte - 1 to 16 MHz External crystal/ceramic resonator - External Clock Input (enabled by option byte) - PLL for multiplying the frequency by 8 or 4 (enabled by option byte). Only multiplying by 8 is available for ROM devices. Reset Sequence Manager (RSM) System Integrity Management (SI) - main supply Low Voltage Detection (LVD) with reset generation (enabled by option byte) Note: 1. DEE0h, DEE1h, DEE2h, and DEE3h addresses are located in a reserved area but are special bytes containing also the RC calibration values which are read-accessible only in user mode. If all the EEPROM data or Flash space (including the RC calibration value locations) has been erased (after the readout protection removal), then the RC calibration values can still be obtained through these four addresses. For compatibility reasons with the SICSR register, CR[1:0] bits are stored in the fifth and sixth position of the DEE1 and DEE3 addresses. 7.1 INTERNAL RC OSCILLATOR ADJUSTMENT The device contains an internal RC oscillator with an accuracy of 1% for a given device, temperature and voltage range (4.5V to 5.5V). It must be calibrated to obtain the frequency required in the application. This is done by the software writing a 10bit calibration value in the RCCR (RC Control Register) and in the bits 6:5 in the SICSR (SI Control Status Register). Whenever the microcontroller is reset, the RCCR returns to its default value (FFh), that is, each time the device is reset, the calibration value must be loaded in the RCCR. Predefined calibration values are stored in EEPROM for 3.3V and 5V VDD supply voltages at 25C, as shown in the following table. Notes: - In 38-pulse ICC mode, the internal RC oscillator is forced as a clock source, regardless of the selection in the option byte. For ST7L1 devices which do not support the internal RC oscillator, the "option byte disabled" mode must be used (35-pulse ICC mode entry, clock provided by the tool). - For more information on the frequency and accuracy of the RC oscillator see "ELECTRICAL CHARACTERISTICS" on page 98. - To improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device. - These bytes are systematically programmed by ST, including on FASTROM devices. Caution: If the voltage or temperature conditions change in the application, the frequency may need to be recalibrated. Refer to application note AN1324 for information on how to calibrate the RC frequency using an external reference signal. 21/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) 7.2 PHASE LOCKED LOOP The PLL can be used to multiply a 1 MHz frequency from the RC oscillator or the external clock by 4 or 8 to obtain fOSC of 4 or 8 MHz. The PLL is enabled and the multiplication factor of 4 or 8 is selected by 2 option bits: - The x4 PLL is intended for operation with VDD in the 3V to 3.6V range (available only on Flash devices) - The x8 PLL is intended for operation with VDD in the 3.6V to 5.5V range1) Refer to Section 15.1 for the option byte description. If the PLL is disabled and the RC oscillator is enabled, then fOSC = 1 MHz. If both the RC oscillator and the PLL are disabled, fOSC is driven by the external clock. Figure 11. PLL Output Frequency Timing Diagram LOCKED bit set 4/8 x input freq. tSTAB Output frequency 7.3 REGISTER DESCRIPTION MAIN CLOCK CONTROL/STATUS REGISTER (MCCSR) Read / Write Reset Value: 0000 0000 (00h) 7 0 0 0 0 0 0 MCO 0 SMS Bits 7:2 = Reserved, must be kept cleared. Bit 1 = MCO Main Clock Out enable This bit is read/write by software and cleared by hardware after a reset. This bit enables the MCO output clock. 0: MCO clock disabled, I/O port free for general purpose I/O. 1: MCO clock enabled. Bit 0 = SMS Slow Mode select This bit is read/write by software and cleared by hardware after a reset. This bit selects the input clock fOSC or fOSC/32. 0: Normal mode (fCPU = fOSC) 1: Slow mode (fCPU = fOSC/32) RC CONTROL REGISTER (RCCR) Read / Write Reset Value: 1111 1111 (FFh) 7 CR9 CR8 CR7 CR6 CR5 CR4 CR3 0 CR2 tLOCK tSTARTUP t When the PLL is started, after reset or wake-up from HALT mode or AWUFH mode, it outputs the clock after a delay of tSTARTUP. When the PLL output signal reaches the operating frequency, the LOCKED bit in the SICSCR register is set. Full PLL accuracy (ACCPLL) is reached after a stabilization time of tSTAB (see Figure 11 and section 13.3.3 on page 105) Refer to section 7.6.3 on page 30 for a description of the LOCKED bit in the SICSR register. Note: 1. It is possible to obtain fOSC = 4 MHz in the 3.3V to 5.5V range with internal RC and PLL enabled by selecting 1 MHz RC and x8 PLL and setting the PLLdiv2 bit in the PLLTST register (see section 7.6.3 on page 30). Bits 7:0 = CR[9:2] RC Oscillator Frequency Adjustment Bits These bits must be written immediately after reset to adjust the RC oscillator frequency and to obtain an accuracy of 1%. The application can store the correct value for each voltage range in EEPROM and write it to this register at start-up. 00h = maximum available frequency FFh = lowest available frequency These bits are used with the CR[1:0] bits in the SICSR register. Refer to section 7.6.3 on page 30. Note: To tune the oscillator, write a series of different values in the register until the correct frequency is reached. The fastest method is to use a dichotomy starting with 80h. 22/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) Figure 12. Clock Management Block Diagram 7 PLLDIV2 0 7 CR9 CR8 CR7 CR6 CR5 CR4 CR3 0 CR2 PLLTST RCCR 7 CR1 CR0 0 SICSR Tunable 1% RC Oscillator OSC,PLLOFF, CLKSEL[1:0] Option bits CLKIN CLKIN CLKIN /2 DIVIDER OSC PLL 1 MHz -> 8 MHz PLL 1 MHz -> 4 MHz CLKIN/2 RC OSC ck_pllx4x8 /2 plldiv2 CLKIN/2 /2 DIVIDER OSC/2 fOSC CLKIN /OSC1 OSC2 OSC 1-16 MHz OSC,PLLOFF, CLKSEL[1:0] Option bits 8-bit LITE TIMER 2 COUNTER fOSC /32 DIVIDER fOSC/32 1 fLTIMER (1ms timebase @ 8 MHz fOSC) fCPU TO CPU AND PERIPHERALS fOSC 0 MCO SMS MCCSR fCPU MCO 23/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) 7.4 MULTI-OSCILLATOR (MO) The main clock of the ST7 can be generated by four different source types coming from the multioscillator block (1 to 16 MHz): An external source Crystal or ceramic resonator oscillators An internal high frequency RC oscillator The associated hardware configurations are shown in Table 4. Refer to Section 13 ELECTRICAL CHARACTERISTICS for more details. 7.4.1 External Clock Source In external clock mode, a clock signal (square, sinus or triangle) with ~50% duty cycle must drive the OSC1 pin while the OSC2 pin is tied to ground. Note: When the Multi-Oscillator is not used, PB4 is selected by default as the external clock. 7.4.2 Crystal/Ceramic Oscillators In this mode, with a self-controlled gain feature, an oscillator of any frequency from 1 to 16 MHz can be placed on OSC1 and OSC2 pins. This family of oscillators has the advantage of producing a very accurate rate on the main clock of the ST7. In this mode of the multi-oscillator, the resonator and the load capacitors must be placed as close as possible to the oscillator pins to minimize output distortion and start-up stabilization time. The loading capacitance values must be adjusted according to the selected oscillator. These oscillators are not stopped during the RESET phase to avoid losing time in the oscillator start-up phase. 7.4.3 Internal RC Oscillator In this mode, the tunable 1% RC oscillator is the main clock source. The two oscillator pins must be tied to ground if dedicated to oscillator use, otherwise they are general purpose I/O. The calibration is done through the RCCR[7:0] and SICSR[6:5] registers. Table 4. ST7 Clock Sources Hardware Configuration External Clock ST7 OSC1 OSC2 EXTERNAL SOURCE Crystal/Ceramic Resonators ST7 OSC1 OSC2 CL1 LOAD CAPACITORS CL2 Internal RC Oscillator ST7 OSC1 OSC2 24/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) 7.5 RESET SEQUENCE MANAGER (RSM) 7.5.1 Introduction The reset sequence manager includes three RESET sources as shown in Figure 14: External RESET source pulse Internal LVD RESET (Low Voltage Detection) Internal WATCHDOG RESET Note: A reset can also be triggered following the detection of an illegal opcode or prebyte code. Refer to section 12.2.1 on page 95 for further details. These sources act on the RESET pin which is always kept low during the delay phase. The RESET service routine vector is fixed at addresses FFFEh-FFFFh in the ST7 memory map. The basic RESET sequence consists of three phases as shown in Figure 13: Active Phase depending on the RESET source 256 or 4096 CPU clock cycle delay (see table below) RESET vector fetch Caution: When the ST7 is unprogrammed or fully erased, the Flash is blank and the RESET vector is not programmed. For this reason, it is recommended to keep the RESET pin in low state until programming mode is entered, in order to avoid unwanted behavior. The 256 or 4096 CPU clock cycle delay allows the oscillator to stabilize and ensures that recovery has taken place from the RESET state. The shorter or longer clock cycle delay is automatically selected depending on the clock source chosen by option byte: CPU Clock Cycle Delay Internal RC Oscillator 256 External clock (connected to CLKIN pin) 256 External Crystal/Ceramic Oscillator 4096 (connected to OSC1/OSC2 pins) Clock Source The RESET vector fetch phase duration is two clock cycles. If the PLL is enabled by option byte, it outputs the clock after an additional delay of tSTARTUP (see Figure 11 on page 22). Figure 13. RESET Sequence Phases RESET INTERNAL RESET Active Phase 256 or 4096 CLOCK CYCLES FETCH VECTOR 7.5.2 Asynchronous External RESET Pin The RESET pin is both an input and an open-drain output with integrated RON weak pull-up resistor. This pull-up has no fixed value but varies in accordance with the input voltage. It can be pulled low by external circuitry to reset the device. See Section 13 ELECTRICAL CHARACTERISTICS for more details. A RESET signal originating from an external source must have a duration of at least th(RSTL)in in order to be recognized (see Figure 15). This detection is asynchronous and therefore the MCU can enter the RESET state even in HALT mode. 25/138 1 ST7L15, ST7L19 Figure 14. Reset Block Diagram VDD RON RESET Filter INTERNAL RESET WATCHDOG RESET ILLEGAL OPCODE RESET1) LVD RESET PULSE GENERATOR Note 1: See "Illegal Opcode Reset" on page 95 for more details on illegal opcode reset conditions. 26/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) The RESET pin is an asynchronous signal which plays a major role in EMS performance. In a noisy environment, it is recommended to follow the guidelines mentioned in Section 13 ELECTRICAL CHARACTERISTICS. 7.5.3 External Power-On RESET If the LVD is disabled by the option byte, to start up the microcontroller correctly, the user must use an external reset circuit to ensure that the reset signal is held low until VDD is over the minimum level specified for the selected fOSC frequency. A proper reset signal for a slow rising VDD supply can generally be provided by an external RC network connected to the RESET pin. 7.5.4 Internal Low Voltage Detector (LVD) RESET Two different RESET sequences caused by the internal LVD circuitry can be distinguished: Power-On RESET Voltage Drop RESET The device RESET pin acts as an output that is pulled low when VDD < VIT+ (rising edge) or VDD < VIT- (falling edge) as shown in Figure 15. The LVD filters spikes on VDD larger than tg(VDD) to avoid parasitic resets. 7.5.5 Internal Watchdog RESET The RESET sequence generated by an internal Watchdog counter overflow is shown in Figure 15. Starting from the Watchdog counter underflow, the device RESET pin acts as an output that is pulled low during at least tw(RSTL)out. Figure 15. RESET Sequences VDD VIT+(LVD) VIT-(LVD) LVD RESET EXTERNAL RESET WATCHDOG RESET RUN ACTIVE PHASE RUN ACTIVE PHASE RUN ACTIVE PHASE RUN th(RSTL)in EXTERNAL RESET SOURCE tw(RSTL)out RESET PIN WATCHDOG RESET WATCHDOG UNDERFLOW INTERNAL RESET (256 or 4096 tCPU) VECTOR FETCH 27/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) 7.6 SYSTEM INTEGRITY MANAGEMENT (SI) The System Integrity Management block contains the Low Voltage Detector (LVD) function. It is managed by the SICSR register. Note: A reset can also be triggered following the detection of an illegal opcode or prebyte code. Refer to section 12.2.1 on page 95 for further details. 7.6.1 Low Voltage Detector (LVD) The Low Voltage Detector (LVD) function generates a static reset when the VDD supply voltage is below a VIT-(LVD) reference value. This means that it secures the power-up as well as the powerdown, keeping the ST7 in reset. The VIT-(LVD) reference value for a voltage drop is lower than the VIT+(LVD) reference value for poweron to avoid a parasitic reset when the MCU starts running and sinks current on the supply (hysteresis). The LVD Reset circuitry generates a reset when VDD is below: - VIT+(LVD) when VDD is rising - VIT-(LVD) when VDD is falling The LVD function is illustrated in Figure 16. Provided the minimum VDD value (guaranteed for the oscillator frequency) is above VIT-(LVD), the MCU can only be in two modes: Figure 16. Low Voltage Detector vs Reset VDD Vhys VIT+(LVD) VIT-(LVD) - Under full software control - In static safe reset In these conditions, secure operation is always ensured for the application without the need for external reset hardware. During a Low Voltage Detector Reset, the RESET pin is held low, thus permitting the MCU to reset other devices. Notes: The LVD allows the device to be used without any external RESET circuitry. The LVD is an optional function which can be selected by the option byte. Use of LVD with capacitive power supply: With this type of power supply, if power cuts occur in the application, it is recommended to pull VDD down to 0V to ensure optimum restart conditions. Refer to the circuit example in Figure 95 on page 119 and note 4. For the application to function correctly, it is recommended to make sure that the VDD supply voltage rises monotonously when the device is exiting from RESET. RESET 28/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) Figure 17. Reset and Supply Management Block Diagram WATCHDOG TIMER (WDG) STATUS FLAG SYSTEM INTEGRITY MANAGEMENT RESET SEQUENCE RESET MANAGER (RSM) SICSR 7 WDGRF LOCKED LVDRF 0 LOW VOLTAGE VSS VDD DETECTOR (LVD) 7.6.2 Low-Power Modes Mode WAIT HALT Description No effect on SI. The SICSR register is frozen. 29/138 1 ST7L15, ST7L19 SUPPLY, RESET AND CLOCK MANAGEMENT (cont'd) 7.6.3 Register Description SYSTEM INTEGRITY (SI) CONTROL/STATUS Bit 2 = LVDRF LVD reset flag REGISTER (SICSR) This bit indicates that the last Reset was generated by the LVD block. It is set by hardware (LVD reRead/Write set) and cleared by software (by reading). When Reset Value: 0110 0xx0 (6xh) the LVD is disabled by OPTION BYTE, the LVDRF bit value is undefined. 7 0 Res CR1 CR0 WDG RF LOCKED LVD RF Res Res Bits 1:0 = Reserved (should be 0) Application notes The LVDRF flag is not cleared when another RESET type occurs (external or watchdog), the LVDRF flag remains set to keep trace of the original failure. In this case, a watchdog reset can be detected by software while an external reset can not. PLL TEST REGISTER (PLLTST) Read/Write Reset Value: 0000 0000(00h) 7 PLLdiv2 0 0 0 0 0 0 Bit 7 = Reserved (should be 0) Bits 6:5 = CR[1:0] RC Oscillator Frequency Adjustment bits These bits, as well as CR[9:2] bits in the RCCR register must be written immediately after reset to adjust the RC oscillator frequency and to obtain an accuracy of 1%. Refer to section 7.3 on page 22. Bit 4 = WDGRF Watchdog Reset flag This bit indicates that the last Reset was generated by the Watchdog peripheral. It is set by hardware (watchdog reset) and cleared by software (writing zero) or an LVD Reset (to ensure a stable cleared state of the WDGRF flag when CPU starts). Combined with the LVDRF flag information, the flag description is given in the following table. RESET Sources External RESET pin Watchdog LVD LVDRF 0 0 1 WDGRF 0 1 X 0 0 Bit 3 = LOCKED PLL Locked Flag This bit is set and cleared by hardware. It is set automatically when the PLL reaches its operating frequency. 0: PLL not locked 1: PLL locked Bit 7: PLLdiv2 PLL clock divide by 2 This bit is read or write by software and cleared by hardware after reset. This bit divides the PLL output clock by 2. 0: PLL output clock 1: Divide by 2 of PLL output clock Refer to "Clock Management Block Diagram" on page 23. Note: Write of this bit is effective after two tCPU cycles (if system clock is 8 MHz) or else one cycle (if system clock is 4 MHz), that is, effective time is 250ns. Bits 6:0: Reserved, must always be cleared. 30/138 1 ST7L15, ST7L19 8 INTERRUPTS The ST7 core may be interrupted by one of two different methods: Maskable hardware interrupts as listed in Table 5, "Interrupt Mapping," on page 32 and a non-maskable software interrupt (TRAP). The Interrupt processing flowchart is shown in Figure 18. The maskable interrupts must be enabled by clearing the I bit in order to be serviced. However, disabled interrupts may be latched and processed when they are enabled (see external interrupts subsection). Note: After reset, all interrupts are disabled. When an interrupt has to be serviced: - Normal processing is suspended at the end of the current instruction execution. - The PC, X, A and CC registers are saved onto the stack. - The I bit of the CC register is set to prevent additional interrupts. - The PC is then loaded with the interrupt vector of the interrupt to service and the first instruction of the interrupt service routine is fetched (refer to the Interrupt Mapping table for vector addresses). The interrupt service routine should finish with the IRET instruction which causes the contents of the saved registers to be recovered from the stack. Note: As a consequence of the IRET instruction, the I bit is cleared and the main program resumes. Priority Management By default, a servicing interrupt cannot be interrupted because the I bit is set by hardware entering in interrupt routine. In the case when several interrupts are simultaneously pending, an hardware priority defines which one will be serviced first (see the Interrupt Mapping table). Interrupts and Low Power Mode All interrupts allow the processor to leave the WAIT low power mode. Only external and specifically mentioned interrupts allow the processor to leave the HALT low power mode (refer to the "Exit from HALT" column in the Interrupt Mapping table). 8.1 NON MASKABLE SOFTWARE INTERRUPT This interrupt is entered when the TRAP instruction is executed regardless of the state of the I bit. It is serviced according to the flowchart in Figure 18. 8.2 EXTERNAL INTERRUPTS External interrupt vectors can be loaded into the PC register if the corresponding external interrupt occurred and if the I bit is cleared. These interrupts allow the processor to leave the HALT low power mode. The external interrupt polarity is selected through the miscellaneous register or interrupt register (if available). An external interrupt triggered on edge will be latched and the interrupt request automatically cleared upon entering the interrupt service routine. Caution: The type of sensitivity defined in the Miscellaneous or Interrupt register (if available) applies to the ei source. In case of a NANDed source (as described in the I/O ports section), a low level on an I/O pin, configured as input with interrupt, masks the interrupt request even in case of risingedge sensitivity. 8.3 PERIPHERAL INTERRUPTS Different peripheral interrupt flags in the status register are able to cause an interrupt when they are active if both: - The I bit of the CC register is cleared. - The corresponding enable bit is set in the control register. If any of these two conditions is false, the interrupt is latched and thus remains pending. Clearing an interrupt request is done by: - Writing "0" to the corresponding bit in the status register or - Access to the status register while the flag is set followed by a read or write of an associated register. Note: The clearing sequence resets the internal latch. A pending interrupt (that is, waiting for being enabled) will therefore be lost if the clear sequence is executed. 31/138 1 ST7L15, ST7L19 INTERRUPTS (cont'd) Figure 18. Interrupt Processing Flowchart FROM RESET I BIT SET? Y N N INTERRUPT PENDING? Y FETCH NEXT INSTRUCTION N IRET? Y STACK PC, X, A, CC SET I BIT LOAD PC FROM INTERRUPT VECTOR EXECUTE INSTRUCTION RESTORE PC, X, A, CC FROM STACK THIS CLEARS I BIT BY DEFAULT Table 5. Interrupt Mapping No. Source Block RESET TRAP 0 1 2 3 4 5 6 7 8 9 10 11 12 13 LITE TIMER SPI AT TIMER AT TIMER AWU ei0 ei1 ei2 ei3 LITE TIMER Reset Software Interrupt Auto Wake-Up Interrupt External Interrupt 0 External Interrupt 1 External Interrupt 2 External Interrupt 3 LITE TIMER RTC2 interrupt Not used Not used AT TIMER Output Compare Interrupt or Input Capture Interrupt AT TIMER Overflow Interrupt LITE TIMER Input Capture Interrupt LITE TIMER RTC1 Interrupt SPI Peripheral Interrupts AT TIMER Overflow Interrupt PWMxCSR or ATCSR ATCSR LTCSR LTCSR SPICSR ATCSR2 Lowest Priority no yes2) no yes2) yes no LTCSR2 no yes Description Register Label Priority Order Exit from HALT or AWUFH yes no yes1) Address Vector FFFEh-FFFFh FFFCh-FFFDh FFFAh-FFFBh FFF8h-FFF9h FFF6h-FFF7h FFF4h-FFF5h FFF2h-FFF3h FFF0h-FFF1h FFEEh-FFEFh FFECh-FFEDh FFEAh-FFEBh FFE8h-FFE9h FFE6h-FFE7h FFE4h-FFE5h FFE2h-FFE3h FFE0h-FFE1h AWUCSR Highest Priority Notes: 1. This interrupt exits the MCU from "Auto Wake-Up from Halt" mode only. 2. These interrupts exit the MCU from "ACTIVE HALT" mode only. 32/138 1 ST7L15, ST7L19 INTERRUPTS (cont'd) EXTERNAL INTERRUPT CONTROL REGISTER (EICR) Read/Write Reset Value: 0000 0000 (00h) 7 IS31 IS30 IS21 IS20 IS11 IS10 IS01 0 IS00 EXTERNAL INTERRUPT SELECTION REGISTER (EISR) Read/Write Reset Value: 0000 1100 (0Ch) 7 ei31 ei30 ei21 ei20 ei11 ei10 ei01 0 ei00 Bits 7:6 = IS3[1:0] ei3 sensitivity These bits define the interrupt sensitivity for ei3 (Port B0) according to Table 6. Bits 5:4 = IS2[1:0] ei2 sensitivity These bits define the interrupt sensitivity for ei2 (Port B3) according to Table 6. Bits 3:2 = IS1[1:0] ei1 sensitivity These bits define the interrupt sensitivity for ei1 (Port A7) according to Table 6. Bits 1:0 = IS0[1:0] ei0 sensitivity These bits define the interrupt sensitivity for ei0 (Port A0) according to Table 6. Notes: 1. These 8 bits can be written only when the I bit in the CC register is set. 2. Changing the sensitivity of a particular external interrupt clears this pending interrupt. This can be used to clear unwanted pending interrupts. Refer to section "External Interrupt Function" on page 43 Table 6. Interrupt Sensitivity Bits ISx1 ISx0 0 0 1 1 0 1 0 1 External Interrupt Sensitivity Falling edge and low level Rising edge only Falling edge only Rising and falling edge Bits 7:6 = ei3[1:0] ei3 pin selection These bits are written by software. They select the Port B I/O pin used for the ei3 external interrupt according to the table below. External Interrupt I/O pin selection ei31 0 0 1 ei30 0 1 0 I/O Pin PB0* PB1 PB2 * Reset State Bits 5:4 = ei2[1:0] ei2 pin selection These bits are written by software. They select the Port B I/O pin used for the ei2 external interrupt according to the table below. External Interrupt I/O pin selection ei21 0 0 1 1 ei20 0 1 0 1 I/O Pin PB3* PB41) PB5 PB6 * Reset State Notes: 1. PB4 cannot be used as an external interrupt in HALT mode. . 33/138 1 ST7L15, ST7L19 INTERRUPTS (cont'd) Bits 3:2 = ei1[1:0] ei1 pin selection These bits are written by software. They select the Port A I/O pin used for the ei1 external interrupt according to the table below. External Interrupt I/O pin selection ei11 0 0 1 1 ei10 0 1 0 1 I/O Pin PA4 PA5 PA6 PA7* Bits 1:0 = ei0[1:0] ei0 pin selection These bits are written by software. They select the Port A I/O pin used for the ei0 external interrupt according to the table below. External Interrupt I/O pin selection ei01 0 0 1 1 ei00 0 1 0 1 I/O Pin PA0 * PA1 PA2 PA3 * Reset State * Reset State 34/138 1 ST7L15, ST7L19 9 POWER SAVING MODES 9.1 INTRODUCTION To give a large measure of flexibility to the application in terms of power consumption, five main power saving modes are implemented in the ST7 (see Figure 19): Slow Wait (and Slow-Wait) Active Halt Auto Wake-Up From Halt (AWUFH) Halt After a RESET, the normal operating mode is selected by default (RUN mode). This mode drives the device (CPU and embedded peripherals) by means of a master clock which is based on the main oscillator frequency divided or multiplied by 2 (fOSC2). From RUN mode, the different power saving modes can be selected by setting the relevant register bits or by calling the specific ST7 software instruction whose action depends on the oscillator status. Figure 19. Power Saving Mode Transitions High RUN SLOW WAIT SLOW WAIT ACTIVE HALT AUTO WAKE-UP FROM HALT HALT Low POWER CONSUMPTION SMS 9.2 SLOW MODE This mode has two targets: - To reduce power consumption by decreasing the internal clock in the device, - To adapt the internal clock frequency (fCPU) to the available supply voltage. SLOW mode is controlled by the SMS bit in the MCCSR register which enables or disables SLOW mode. In this mode, the oscillator frequency is divided by 32. The CPU and peripherals are clocked at this lower frequency. Note: SLOW-WAIT mode is activated when entering WAIT mode while the device is already in SLOW mode. Figure 20. SLOW Mode Clock Transition fOSC/32 fCPU fOSC fOSC NORMAL RUN MODE REQUEST 35/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) 9.3 WAIT MODE WAIT mode places the MCU into a low power consumption mode by stopping the CPU. This power saving mode is selected by calling the `WFI' instruction. All peripherals remain active. During WAIT mode, the I bit of the CC register is cleared to enable all interrupts. All other registers and memory remain unchanged. The MCU remains in WAIT mode until an interrupt or reset occurs, whereupon it wakes up and the Program Counter branches to the starting address of the interrupt or reset service routine. Refer to Figure 21. Figure 21. WAIT Mode Flowchart OSCILLATOR PERIPHERALS CPU I BIT ON ON OFF 0 WFI INSTRUCTION N RESET N INTERRUPT Y OSCILLATOR PERIPHERALS CPU I BIT ON OFF ON 0 Y 256 OR 4096 CPU CLOCK CYCLE DELAY OSCILLATOR PERIPHERALS CPU I BIT ON ON ON X1) FETCH RESET VECTOR OR SERVICE INTERRUPT Notes: 1. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped. 36/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) 9.4 HALT MODE The HALT mode is the lowest power consumption mode of the MCU. It is entered by executing the `HALT' instruction when ACTIVE HALT is disabled (see section 9.5 on page 38 for more details) and when the AWUEN bit in the AWUCSR register is cleared. The MCU can exit HALT mode on reception of either a specific interrupt (see Table 5, "Interrupt Mapping," on page 32) or a RESET. When exiting HALT mode by means of a RESET or an interrupt, the oscillator is immediately turned on and the 256 or 4096 CPU cycle delay is used to stabilize the oscillator. After the start-up delay, the CPU resumes operation by servicing the interrupt or by fetching the reset vector which woke it up (see Figure 23). When entering HALT mode, the I bit in the CC register is forced to 0 to enable interrupts. Therefore, if an interrupt is pending, the MCU wakes up immediately. In HALT mode, the main oscillator is turned off, stopping all internal processing, including the operation of the on-chip peripherals. All peripherals are not clocked except those which receive their clock supply from another clock generator (such as an external or auxiliary oscillator). The compatibility of Watchdog operation with HALT mode is configured by the "WDGHALT" option bit of the option byte. The HALT instruction, when executed while the Watchdog system is enabled, can generate a Watchdog RESET (see section 15.1 on page 126 for more details). Figure 22. HALT Timing Overview RUN HALT 256 OR 4096 CPU CYCLE DELAY RESET OR INTERRUPT FETCH VECTOR RUN Figure 23. HALT Mode Flowchart HALT INSTRUCTION (Active Halt disabled) (AWUCSR.AWUEN=0) ENABLE WDGHALT1) 1 WATCHDOG RESET OSCILLATOR OFF PERIPHERALS2) OFF CPU OFF I BIT 0 0 WATCHDOG DISABLE N N RESET Y INTERRUPT3) Y OSCILLATOR PERIPHERALS CPU I BIT ON OFF ON X4) 256 OR 4096 CPU CLOCK CYCLE DELAY5) OSCILLATOR PERIPHERALS CPU I BIT ON ON ON X4) FETCH RESET VECTOR OR SERVICE INTERRUPT Notes: 1. WDGHALT is an option bit. See option byte section for more details. 2. Peripheral clocked with an external clock source can still be active. 3. Only some specific interrupts can exit the MCU from HALT mode (such as external interrupt). Refer to Table 5, "Interrupt Mapping," on page 32 for more details. 4. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped. 5. If the PLL is enabled by option byte, it outputs the clock after a delay of tSTARTUP (see Figure 11 on page 22). HALT INSTRUCTION [Active Halt disabled] 37/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) 9.4.1 Halt Mode Recommendations - Make sure that an external event is available to wake up the microcontroller from HALT mode. - When using an external interrupt to wake up the microcontroller, re-initialize the corresponding I/O as "Input Pull-up with Interrupt" before executing the HALT instruction. The main reason for this is that the I/O may be incorrectly configured due to external interference or by an unforeseen logical condition. - For the same reason, re-initialize the level sensitiveness of each external interrupt as a precautionary measure. - The opcode for the HALT instruction is 0x8E. To avoid an unexpected HALT instruction due to a program counter failure, it is advised to clear all occurrences of the data value 0x8E from memory. For example, avoid defining a constant in program memory with the value 0x8E. - As the HALT instruction clears the interrupt mask in the CC register to allow interrupts, the user may choose to clear all pending interrupt bits before executing the HALT instruction. This avoids entering other peripheral interrupt routines after executing the external interrupt routine corresponding to the wake-up event (reset or external interrupt). 9.5 ACTIVE HALT MODE ACTIVE HALT mode is the lowest power consumption mode of the MCU with a real time clock available. It is entered by executing the `HALT' instruction. The decision to enter either in ACTIVE HALT or HALT mode is given by the LTCSR/ATCSR register status as shown in the following table: ATCSR LTCSR1 ATCSR ATCSR OVFIE TB1IE bit CK1 bit CK0 bit bit 0 0 1 x x 0 x 1 x x x 0 0 x x 1 Meaning ACTIVE HALT mode disabled ACTIVE HALT mode enabled operation by fetching the reset vector which woke it up (see Figure 25). - When exiting ACTIVE HALT mode by means of an interrupt, the CPU immediately resumes operation by servicing the interrupt vector which woke it up (see Figure 25). When entering ACTIVE HALT mode, the I bit in the CC register is cleared to enable interrupts. Therefore, if an interrupt is pending, the MCU wakes up immediately (see Note 3). In ACTIVE HALT mode, only the main oscillator and the selected timer counter (LT/AT) are running to keep a wake-up time base. All other peripherals are not clocked except those which receive their clock supply from another clock generator (such as external or auxiliary oscillator). Note: As soon as ACTIVE HALT is enabled, executing a HALT instruction while the Watchdog is active does not generate a RESET. This means that the device cannot exceed a defined delay in this power saving mode. Figure 24. ACTIVE HALT Timing Overview ACTIVE 256 OR 4096 CPU HALT CYCLE DELAY1) RESET OR INTERRUPT RUN RUN HALT INSTRUCTION [Active Halt Enabled] FETCH VECTOR The MCU exits ACTIVE HALT mode on reception of a specific interrupt (see Table 5, "Interrupt Mapping," on page 32) or a RESET. - When exiting ACTIVE HALT mode by means of a RESET, a 256 or 4096 CPU cycle delay occurs. After the start-up delay, the CPU resumes 38/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) Figure 25. ACTIVE HALT Mode Flowchart HALT INSTRUCTION (Active Halt enabled) (AWUCSR.AWUEN=0) OSCILLATOR ON PERIPHERALS2) OFF CPU OFF I BIT 0 Figure 26. AWUFH Mode Block Diagram AWU RC oscillator fAWU_RC to Timer input capture N RESET N Y INTERRUPT3) Y OSCILLATOR PERIPHERALS2) CPU I BIT ON OFF ON X4) /64 divider AWUFH prescaler/1 .. 255 AWUFH interrupt (ei0 source) 256 OR 4096 CPU CLOCK CYCLE DELAY OSCILLATOR PERIPHERALS CPU I BIT ON ON ON X4) FETCH RESET VECTOR OR SERVICE INTERRUPT Notes: 1. This delay occurs only if the MCU exits ACTIVE HALT mode by means of a RESET. 2. Peripherals clocked with an external clock source can still be active. 3. Only the RTC1 interrupt and some specific interrupts can exit the MCU from ACTIVE HALT mode. Refer to Table 5, "Interrupt Mapping," on page 32 for more details. 4. Before servicing an interrupt, the CC register is pushed on the stack. The I bit of the CC register is set during the interrupt routine and cleared when the CC register is popped. As soon as HALT mode is entered and if the AWUEN bit has been set in the AWUCSR register, the AWU RC oscillator provides a clock signal (fAWU_RC). Its frequency is divided by a fixed divider and a programmable prescaler controlled by the AWUPR register. The output of this prescaler provides the delay time. When the delay has elapsed, the AWUF flag is set by hardware and an interrupt wakes up the MCU from HALT mode. At the same time, the main oscillator is immediately turned on and a 256 or 4096 cycle delay is used to stabilize it. After this start-up delay, the CPU resumes operation by servicing the AWUFH interrupt. The AWU flag and its associated interrupt are cleared by software reading the AWUCSR register. To compensate for any frequency dispersion of the AWU RC oscillator, it can be calibrated by measuring the clock frequency fAWU_RC and then calculating the right prescaler value. Measurement mode is enabled by setting the AWUM bit in the AWUCSR register in Run mode. This connects fAWU_RC to the input capture of the 12-bit Auto-Reload timer, allowing the fAWU_RC to be measured using the main oscillator clock as a reference timebase. 9.6 AUTO WAKE-UP FROM HALT MODE Auto Wake-Up From Halt (AWUFH) mode is similar to HALT mode with the addition of a specific internal RC oscillator for wake-up (Auto Wake-Up from Halt Oscillator). Compared to ACTIVE HALT mode, AWUFH has lower power consumption (the main clock is not kept running but there is no accurate realtime clock available). It is entered by executing the HALT instruction when the AWUEN bit in the AWUCSR register has been set. 39/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) Similarities with Halt mode The following AWUFH mode behavior is the same as normal HALT mode: - The MCU can exit AWUFH mode by means of any interrupt with exit from Halt capability or a reset (see Section 9.4 HALT MODE). - When entering AWUFH mode, the I bit in the CC register is forced to 0 to enable interrupts. Therefore, if an interrupt is pending, the MCU wakes up immediately. - In AWUFH mode, the main oscillator is turned off, stopping all internal processing, including the operation of the on-chip peripherals. None of the peripherals are clocked except those which receive their clock supply from another clock generator (such as an external or auxiliary oscillator like the AWU oscillator). - The compatibility of Watchdog operation with AWUFH mode is configured by the WDGHALT option bit in the option byte. Depending on this setting, the HALT instruction, when executed while the Watchdog system is enabled, can generate a Watchdog RESET. Figure 27. AWUF Halt Timing Diagram tAWU RUN MODE fCPU fAWU_RC Clear by software AWUFH interrupt HALT MODE 256 OR 4096 tCPU RUN MODE 40/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) Figure 28. AWUFH Mode Flowchart HALT INSTRUCTION (Active Halt disabled) (AWUCSR.AWUEN=1) ENABLE WDGHALT1) 1 WATCHDOG RESET AWU RC OSC MAIN OSC PERIPHERALS2) CPU I[1:0] BITS ON OFF OFF OFF 10 0 WATCHDOG DISABLE the current software priority level of the interrupt routine and recovered when the CC register is popped. 5. If the PLL is enabled by the option byte, it outputs the clock after an additional delay of tSTARTUP (see Figure 11). N RESET N Y INTERRUPT3) Y AWU RC OSC MAIN OSC PERIPHERALS CPU I[1:0] BITS OFF ON OFF ON XX4) 256 OR 4096 CPU CLOCK CYCLE DELAY5) AWU RC OSC MAIN OSC PERIPHERALS CPU I[1:0] BITS OFF ON ON ON XX4) FETCH RESET VECTOR OR SERVICE INTERRUPT Notes: 1. WDGHALT is an option bit. See option byte section for more details. 2. Peripheral clocked with an external clock source can still be active. 3. Only an AWUFH interrupt and some specific interrupts can exit the MCU from HALT mode (such as external interrupt). Refer to Table 5, "Interrupt Mapping," on page 32 for more details. 4. Before servicing an interrupt, the CC register is pushed on the stack. The I[1:0] bits of the CC register are set to 41/138 1 ST7L15, ST7L19 POWER SAVING MODES (cont'd) 9.6.0.1 Register Description AWUFH CONTROL/STATUS REGISTER (AWUCSR) Read/Write Reset Value: 0000 0000 (00h) 7 0 0 0 0 0 AWUFH PRESCALER REGISTER (AWUPR) Read/Write Reset Value: 1111 1111 (FFh) 7 0 0 AWUP AWUP AWUP AWUP AWUP AWUP AWUP AWUP R7 R6 R5 R4 R3 R2 R1 R0 AWUF AWUM AWUEN Bits 7:3 = Reserved. Bit 1 = AWUF Auto Wake-Up Flag This bit is set by hardware when the AWU module generates an interrupt and cleared by software on reading AWUCSR. Writing to this bit does not change its value. 0: No AWU interrupt occurred 1: AWU interrupt occurred Bit 1 = AWUM Auto Wake-Up Measurement This bit enables the AWU RC oscillator and connects its output to the input capture of the 12-bit Auto-Reload timer. This allows the timer to measure the AWU RC oscillator dispersion and then compensate this dispersion by providing the right value in the AWUPRE register. 0: Measurement disabled 1: Measurement enabled Bit 0 = AWUEN Auto Wake-Up From Halt Enabled This bit enables the Auto Wake-Up From Halt feature: Once HALT mode is entered, the AWUFH wakes up the microcontroller after a time delay dependent on the AWU prescaler value. It is set and cleared by software. 0: AWUFH (Auto Wake-Up From Halt) mode disabled 1: AWUFH (Auto Wake-Up From Halt) mode enabled Table 7. AWU Register Map and Reset Values Address (Hex.) 0049h 004Ah Register Label AWUPR Reset Value AWUCSR Reset Value 7 6 5 Bits 7:0 = AWUPR[7:0] Auto Wake-Up Prescaler These 8 bits define the AWUPR Dividing factor (as explained below: AWUPR[7:0] 00h 01h ... FEh FFh Dividing factor Forbidden 1 ... 254 255 In AWU mode, the period that the MCU stays in Halt Mode (tAWU in Figure 27 on page 40) is defined by t AWU 1 = 64 x AWUPR x ------------------------- + t RCSTRT f AWURC This prescaler register can be programmed to modify the time that the MCU stays in HALT mode before waking up automatically. Note: If 00h is written to AWUPR, depending on the product, an interrupt is generated immediately after a HALT instruction or the AWUPR remains unchanged. 4 3 2 1 0 AWUPR7 AWUPR6 AWUPR5 AWUPR4 AWUPR3 AWUPR2 AWUPR1 AWUPR0 1 1 1 1 1 1 1 1 0 0 0 0 0 AWUF AWUM AWUEN 42/138 1 ST7L15, ST7L19 10 I/O PORTS 10.1 INTRODUCTION The I/O ports allow data transfer. An I/O port contains up to eight pins. Each pin can be programmed independently either as a digital input or digital output. In addition, specific pins may have several other functions. These functions can include external interrupt, alternate signal input/output for on-chip peripherals or analog input. 10.2 FUNCTIONAL DESCRIPTION A Data Register (DR) and a Data Direction Register (DDR) are always associated with each port. The Option Register (OR), which allows input/output options, may or may not be implemented. The following description takes into account the OR register. Refer to the Port Configuration table for device specific information. An I/O pin is programmed using the corresponding bits in the DDR, DR and OR registers: Bit x corresponding to pin x of the port. Figure 29 shows the generic I/O block diagram. 10.2.1 Input Modes Clearing the DDRx bit selects input mode. In this mode, reading its DR bit returns the digital value from that I/O pin. If an OR bit is available, different input modes can be configured by software: Floating or pull-up. Refer to Section 10.3 I/O PORT IMPLEMENTATION for configuration. Notes: 1. Writing to the DR modifies the latch value but does not change the state of the input pin. 2. Do not use read/modify/write instructions (BSET/BRES) to modify the DR register. 10.2.1.1 External Interrupt Function External interrupt capability is selected using the EISR register. If EISR bits are <> 0, the corresponding pin is used as external interrupt. In this case, the ORx bit can select the pin as either interrupt floating or interrupt pull-up. In this configuration, a signal edge or level input on the I/O generates an interrupt request via the corresponding interrupt vector (eix). Falling or rising edge sensitivity is programmed independently for each interrupt vector. The External Interrupt Control Register (EICR) or the Miscellaneous Register controls this sensitivity, depending on the device. A device may have up to seven external interrupts. Several pins may be tied to one external interrupt vector. Refer to "PIN DESCRIPTION" on page 5 to see which ports have external interrupts. If several I/O interrupt pins on the same interrupt vector are selected simultaneously, they are logically combined. For this reason, if one of the interrupt pins is tied low, it may mask the others. External interrupts are hardware interrupts. Fetching the corresponding interrupt vector automatically clears the request latch. Changing the sensitivity of a particular external interrupt clears this pending interrupt. This can be used to clear unwanted pending interrupts. Spurious interrupts When enabling/disabling an external interrupt by setting/resetting the related OR register bit, a spurious interrupt is generated if the pin level is low and its edge sensitivity includes falling/rising edge. This is due to the edge detector input, which is switched to '1' when the external interrupt is disabled by the OR register. To avoid this unwanted interrupt, a "safe" edge sensitivity (rising edge for enabling and falling edge for disabling) must be selected before changing the OR register bit and configuring the appropriate sensitivity again. Caution: If a pin level change occurs during these operations (asynchronous signal input), as interrupts are generated according to the current sensitivity, it is advised to disable all interrupts before and to re-enable them after the complete previous sequence in order to avoid an external interrupt occurring on the unwanted edge. This corresponds to the following steps: 1. To enable an external interrupt: - Set the interrupt mask with the SIM instruction (in cases where a pin level change could occur) - Select rising edge - Enable the external interrupt through the OR register - Select the desired sensitivity if different from rising edge - Reset the interrupt mask with the RIM instruction (in cases where a pin level change could occur) 2. To disable an external interrupt: 43/138 1 ST7L15, ST7L19 I/O PORTS (cont'd) - Set the interrupt mask with the SIM instruction SIM (in cases where a pin level change could occur) - Select falling edge - Disable the external interrupt through the OR register - Select rising edge - Reset the interrupt mask with the RIM instruction (in cases where a pin level change could occur) 10.2.2 Output Modes Setting the DDRx bit selects output mode. Writing to the DR bits applies a digital value to the I/O through the latch. Reading the DR bits returns the previously stored value. If an OR bit is available, different output modes can be selected by software: Push-pull or opendrain. Refer to "I/O PORT IMPLEMENTATION" on page 47 for configuration. DR Value and Output Pin Status DR 0 1 Push-Pull VOL VOH Open-Drain VOL Floating 10.2.3 Alternate Functions Many ST7 I/Os have one or more alternate functions. These may include output signals from, or input signals to, on-chip peripherals. The Device Pin Description table describes which peripheral signals can be input/output to which ports. A signal coming from an on-chip peripheral can be output on an I/O. To do this, enable the on-chip peripheral as an output (enable bit in the peripheral's control register). The peripheral configures the I/O as an output and takes priority over standard I/ O programming. The I/O's state is readable by addressing the corresponding I/O data register. Configuring an I/O as floating enables alternate function input. It is not recommended to configure an I/O as pull-up as this increases current consumption. Before using an I/O as an alternate input, configure it without interrupt. Otherwise spurious interrupts can occur. Configure an I/O as input floating for an on-chip peripheral signal which can be input and output. Caution: I/Os which can be configured as both an analog and digital alternate function need special attention. The user must control the peripherals so that the signals do not arrive at the same time on the same pin. If an external clock is used, only the clock alternate function should be employed on that I/O pin and not the other alternate function. 44/138 1 ST7L15, ST7L19 I/O PORTS (cont'd) Figure 29. I/O Port General Block Diagram REGISTER ACCESS ALTERNATE OUTPUT From on-chip peripheral 1 0 VDD P-BUFFER (see table below) PULL-UP (see table below) VDD ALTERNATE ENABLE BIT DR DDR PULL-UP CONDITION DATA BUS PAD OR OR SEL If implemented N-BUFFER DDR SEL CMOS SCHMITT TRIGGER DIODES (see table below) ANALOG INPUT DR SEL 1 0 ALTERNATE INPUT Combinational Logic To on-chip peripheral EXTERNAL INTERRUPT REQUEST (eix) SENSITIVITY SELECTION FROM OTHER BITS Note: Refer to the Port Configuration table for device specific information. Table 8. Port Mode Options Configuration Mode Input Output Floating with/without Interrupt Pull-up with/without Interrupt Push-pull Open Drain (logic level) Pull-Up Off On Off P-Buffer Off On Off On On Diodes to VDD to VSS Legend: Off - implemented not activated On - implemented and activated 45/138 1 ST7L15, ST7L19 I/O PORTS (cont'd) Table 9. I/O Configurations Hardware Configuration DR REGISTER ACCESS DR REGISTER PAD W DATA BUS R INPUT 1) FROM OTHER PINS INTERRUPT COMBINATIONAL POLARITY LOGIC SELECTION CONDITION ALTERNATE INPUT To on-chip peripheral EXTERNAL INTERRUPT SOURCE (eix) ANALOG INPUT OPEN-DRAIN OUTPUT 2) DR REGISTER ACCESS PAD DR REGISTER R/W DATA BUS DR REGISTER ACCESS PUSH-PULL OUTPUT 2) PAD DR REGISTER R/W DATA BUS ALTERNATE ENABLE BIT ALTERNATE OUTPUT From on-chip peripheral Notes: 1. When the I/O port is in input configuration and the associated alternate function is enabled as an output, reading the DR register reads the alternate function output status. 2. When the I/O port is in output configuration and the associated alternate function is enabled as an input, the alternate function reads the pin status given by the DR register content. 46/138 1 ST7L15, ST7L19 I/O PORTS (cont'd) Analog alternate function Configure the I/O as floating input to use an ADC input. The analog multiplexer (controlled by the ADC registers) switches the analog voltage present on the selected pin to the common analog rail, connected to the ADC input. Analog Recommendations Do not change the voltage level or loading on any I/O while conversion is in progress. Do not have clocking pins located close to a selected analog pin. WARNING: The analog input voltage level must be within the limits stated in the absolute maximum ratings. 10.3 I/O PORT IMPLEMENTATION The hardware implementation on each I/O port depends on the settings in the DDR and OR registers and specific I/O port features such as ADC input or open drain. Switching these I/O ports from one state to another should be done in a sequence that prevents unwanted side effects. Recommended safe transitions are illustrated in Figure 30. Other transitions are potentially risky and should be avoided, since they may present unwanted side-effects such as spurious interrupt generation. Figure 30. Interrupt I/O Port State Transitions 01 INPUT floating/pull-up interrupt 10.5 LOW-POWER MODES Mode WAIT HALT Description No effect on I/O ports. External interrupts cause the device to exit from WAIT mode. No effect on I/O ports. External interrupts cause the device to exit from HALT mode. 10.6 INTERRUPTS The external interrupt event generates an interrupt if the corresponding configuration is selected with DDR and OR registers and if the I bit in the CC register is cleared (RIM instruction). Interrupt Event External interrupt on selected external event Enable Event Control Flag Bit DDRx ORx Exit from Wait Yes Exit from Halt Yes Related Documentation SPI Communication between ST7 and EEPROM (AN970) S/W implementation of I2C bus master (AN1045) Software LCD driver (AN1048) 00 INPUT floating (reset state) 10 OUTPUT open-drain 11 OUTPUT push-pull XX = DDR, OR 10.4 UNUSED I/O PINS Unused I/O pins must be connected to fixed voltage levels. Refer to section 13.8 on page 113. 47/138 1 ST7L15, ST7L19 I/O PORTS (cont'd) 10.7 DEVICE-SPECIFIC I/O PORT CONFIGURATION The I/O port register configurations are summarized as follows: Standard Ports PA7:0, PB6:0 MODE floating input pull-up input open drain output push-pull output DDR 0 0 1 1 OR 0 1 0 1 Interrupt Ports Ports where the external interrupt capability is selected using the EISR register MODE floating input pull-up interrupt input open drain output push-pull output DDR 0 0 1 1 OR 0 1 0 1 PC1:0 (multiplexed with OSC1,OSC2) MODE floating input push-pull output DDR 0 1 The selection between OSC1 or PC0 and OSC2 or PC1 is done by the option byte (refer to section 15.1 on page 126). Interrupt capability is not available on PC1:0. Port C is not present on ROM devices. Note: PCOR not implemented but p-transistor always active in output mode (refer to Figure 29 on page 45). Table 10. Port Configuration (Standard Ports) Port Port A Port B Pin name PA7:0 PB6:0 Input OR = 0 floating floating Output OR = 1 pull-up pull-up OR = 0 open drain open drain OR = 1 push-pull push-pull Note: On ports where the external interrupt capability is selected using the EISR register, the configuration is as follows: Port Port A Port B Pin name PA7:0 PB6:0 Input OR = 0 floating floating Output OR = 1 pull-up interrupt pull-up interrupt OR = 0 open drain open drain OR = 1 push-pull push-pull Table 11. I/O Port Register Map and Reset Values Address (Hex.) 0000h 0001h Register Label PADR Reset Value PADDR Reset Value 7 MSB 1 MSB 0 0 0 0 0 0 0 1 1 1 1 1 1 6 5 4 3 2 1 0 LSB 1 LSB 0 48/138 1 ST7L15, ST7L19 Address (Hex.) 0002h 0003h 0004h 0005h 0006h 0007h Register Label PAOR Reset Value PBDR Reset Value PBDDR Reset Value PBOR Reset Value PCDR Reset Value PCDDR Reset Value 7 MSB 0 MSB 1 MSB 0 MSB 0 MSB 0 MSB 0 6 5 4 3 2 1 0 LSB 1 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 1 0 0 LSB 1 LSB 0 LSB 0 LSB 1 LSB 0 10.8 MULTIPLEXED INPUT/OUTPUT PORTS OSC1/PC0 are multiplexed on one pin (pin20) and OSC2/PC1 are multiplexed on another pin (pin19). 49/138 1 ST7L15, ST7L19 11 ON-CHIP PERIPHERALS 11.1 WATCHDOG TIMER (WDG) 11.1.1 Introduction The Watchdog timer is used to detect the occurrence of a software fault, usually generated by external interference or by unforeseen logical conditions, which causes the application program to abandon its normal sequence. The Watchdog circuit generates an MCU reset upon expiration of a programmed time period, unless the program refreshes the counter's contents before the T6 bit is cleared. 11.1.2 Main Features Programmable free-running downcounter (64 increments of 16000 CPU cycles) Programmable reset Figure 31. Watchdog Block Diagram RESET Reset (if watchdog activated) when the T6 bit reaches zero Optional reset on HALT instruction (configurable by option byte) Hardware Watchdog selectable by option byte 11.1.3 Functional Description The counter value stored in the CR register (bits T[6:0]) is decremented every 16000 machine cycles and the length of the timeout period can be programmed by the user in 64 increments. If the watchdog is activated (the WDGA bit is set) and when the 7-bit timer (bits T[6:0]) rolls over from 40h to 3Fh (T6 becomes cleared), it initiates a reset cycle pulling low the reset pin for typically 30s. WATCHDOG CONTROL REGISTER (CR) WDGA T6 T5 T4 T3 T2 T1 T0 7-bit DOWNCOUNTER fCPU CLOCK DIVIDER /16000 50/138 1 ST7L15, ST7L19 ON-CHIP PERIPHERALS (cont'd) The application program must write in the CR register at regular intervals during normal operation to prevent an MCU reset. This downcounter is freerunning: It counts down, even if the watchdog is disabled. The value to be stored in the CR register must be between FFh and C0h (see Table 12 .Watchdog Timing): - The WDGA bit is set (watchdog enabled). - The T6 bit is set to prevent generating an immediate reset. - The T[5:0] bits contain the number of increments which represents the time delay before the watchdog produces a reset. Following a reset, the watchdog is disabled. Once activated, it can be disabled only by a reset. The T6 bit can generate a software reset (the WDGA bit is set and the T6 bit is cleared). If the watchdog is activated, the HALT instruction generates a Reset. Table 12.Watchdog Timing WDG Counter Code C0h FFh fCPU = 8 MHz min (ms) 1 127 max (ms) 2 128 11.1.4.1 Using Halt Mode with the WDG (WDGHALT Option) If HALT mode with Watchdog is enabled by the option byte (no watchdog reset on HALT instruction), it is recommended before executing the HALT instruction to refresh the WDG counter, to avoid an unexpected WDG reset immediately after waking up the microcontroller (same behavior in ACTIVE HALT mode). 11.1.5 Interrupts None. 11.1.6 Register Description CONTROL REGISTER (WDGCR) Read/Write Reset Value: 0111 1111 (7Fh) 7 WDGA T6 T5 T4 T3 T2 T1 0 T0 Notes: 1. The timing variation shown in Table 12 is due to the unknown status of the prescaler when writing to the CR register. 2. The number of CPU clock cycles applied during the RESET phase (256 or 4096) must be taken into account in addition to these timings. 11.1.4 Hardware Watchdog Option If Hardware Watchdog is selected by the option byte, the watchdog is always active and the WDGA bit in the CR is not used. Refer to the Option Byte description in section 15 on page 126. Bit 7 = WDGA Activation bit. This bit is set by software and only cleared by hardware after a reset. When WDGA = 1, the watchdog can generate a reset. 0: Watchdog disabled 1: Watchdog enabled Note: This bit is not used if the hardware watchdog option is enabled by option byte. Bits 6:0 = T[6:0] 7-bit timer (MSB to LSB). These bits contain the decremented value. A reset is produced when it rolls over from 40h to 3Fh (T6 becomes cleared). Table 13. Watchdog Timer Register Map and Reset Values Address (Hex.) 002Eh Register Label WDGCR Reset Value 7 WDGA 0 6 T6 1 5 T5 1 4 T4 1 3 T3 1 2 T2 1 1 T1 1 0 T0 1 51/138 1 ST7L15, ST7L19 11.2 DUAL 12-BIT AUTORELOAD TIMER 4 (AT4) 11.2.1 Introduction The 12-bit Autoreload Timer can be used for general-purpose timing functions. It is based on one or two free-running 12-bit upcounters with an input capture register and four PWM output channels. There are seven external pins: - 4 PWM outputs - ATIC/LTIC pins for the Input Capture function - BREAK pin for forcing a break condition on the PWM outputs 11.2.2 Main Features Single Timer or Dual Timer mode with two 12-bit upcounters (CNTR1/CNTR2) and two 12-bit autoreload registers (ATR1/ATR2) Maskable overflow interrupts PWM mode - Generation of four independent PWMx signals Figure 32. Single Timer Mode (ENCNTR2 = 0) - Dead time generation for Half-Bridge driving mode with programmable dead time - Frequency 2 kHz to 4 MHz (@ 8 MHz fCPU) - Programmable duty-cycles - Polarity control - Programmable output modes Output Compare Mode Input Capture Mode - 12-bit input capture register (ATICR) - Triggered by rising and falling edges - Maskable IC interrupt - Long range input capture Break control Flexible Clock control One Pulse mode on PWM2/3 (available only on Flash devices) Force Update (available only on Flash devices) ATIC Edge Detection Circuit 12-bit Input Capture Output Compare CMP Interrupt OE0 Dead Time Generator OE1 Break Function PWM0 Duty Cycle Generator PWM1 Duty Cycle Generator 12-bit Autoreload Register 1 PWM2 Duty Cycle Generator 12-bit Upcounter 1 PWM3 Duty Cycle Generator OVF1 interrupt PWM0 PWM1 DTE bit OE2 PWM2 OE3 PWM3 BPEN bit Clock Control OFF fCPU 1ms from Lite Timer 52/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) Figure 33. Dual Timer Mode (ENCNTR2 = 1) ATIC Edge Detection Circuit 12-bit Input Capture Output Compare CMP Interrupt OE0 Dead Time Generator OE1 Break Function 12-bit Autoreload Register 1 PWM0 Duty Cycle Generator PWM1 Duty Cycle Generator OVF1 interrupt OVF2 interrupt PWM0 PWM1 12-bit Upcounter 1 DTE bit OE2 One Pulse mode OE3 12-bit Upcounter 2 PWM2 Duty Cycle Generator PWM3 Duty Cycle Generator PWM2 PWM3 12-bit Autoreload Register 2 Output Compare OP_EN bit BPEN bit Clock Control OFF fCPU 1ms from Lite Timer CMP Interrupt LTIC 53/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3 Functional Description 11.2.3.1 PWM Mode This mode allows up to four Pulse Width Modulated signals to be generated on the PWMx output pins. PWM Frequency The four PWM signals can have the same frequency (fPWM) or can have two different frequencies. This is selected by the ENCNTR2 bit which enables single timer or dual timer mode (see Figure 32 and Figure 33). The frequency is controlled by the counter period and the ATR register value. In dual timer mode, PWM2 and PWM3 can be generated with a different frequency controlled by CNTR2 and ATR2. fPWM = fCOUNTER / (4096 - ATR) Following the above formula, - If fCOUNTER is 4 MHz, the maximum value of fPWM is 2 MHz (ATR register value = 4094),the minimum value is 1 kHz (ATR register value = 0). - If fCOUNTER is 32 MHz, the maximum value of fPWM is 8 MHz (ATR register value = 4092), the minimum value is 8 kHz (ATR register value = 0). Notes: 1. The maximum value of ATR is 4094 because it must be lower than the DC4R value, which in this case must be 4095. 2. To update the DCRx registers at 32 MHz, the following precautions must be taken: - if the PWM frequency is < 1 MHz and the TRANx bit is set asynchronously, it should be set twice after a write to the DCRx registers. - if the PWM frequency is > 1 MHz, the TRANx bit should be set along with FORCEx bit with the same instruction (use a load instruction and not two bset instructions). Duty Cycle The duty cycle is selected by programming the DCRx registers. These are preload registers. The DCRx values are transferred in Active duty cycle registers after an overflow event if the corresponding transfer bit (TRANx bit) is set. The TRAN1 bit controls the PWMx outputs driven by Counter 1 and the TRAN2 bit controls the PWMx outputs driven by Counter 2. PWM generation and output compare are done by comparing these active DCRx values with the counter. The maximum available resolution for the PWMx duty cycle is: Resolution = 1 / (4096 - ATR) where ATR is equal to 0. With this maximum resolution, 0% and 100% duty cycle can be obtained by changing the polarity. At reset, the counter starts counting from 0. When an upcounter overflow occurs (OVF event), the preloaded Duty cycle values are transferred to the active Duty Cycle registers and the PWMx signals are set to a high level. When the upcounter matches the active DCRx value, the PWMx signals are set to a low level. To obtain a signal on a PWMx pin, the contents of the corresponding active DCRx register must be greater than the contents of the ATR register. Note for ROM devices only: The PWM can be enabled/disabled only in overflow ISR, otherwise the first pulse of PWM can be different from expected one because no force overflow function is present. The maximum value of ATR is 4094 because it must be lower than the DCR value, which in this case must be 4095. Polarity Inversion The polarity bits can be used to invert any of the four output signals. The inversion is synchronized with the counter overflow if the corresponding transfer bit in the ATCSR2 register is set (reset value). See Figure 34. Figure 34. PWM Polarity Inversion inverter PWMx PWMx PIN PWMxCSR Register OPx TRANx ATCSR2 Register counter overflow DFF The Data Flip Flop (DFF) applies the polarity inversion when triggered by the counter overflow input. Output Control The PWMx output signals can be enabled or disabled using the OEx bits in the PWMCR register. 54/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) Figure 35. PWM Function 4095 DUTY CYCLE REGISTER (DCRx) COUNTER AUTO-RELOAD REGISTER (ATR) 000 t PWMx OUTPUT WITH OE=1 AND OPx=0 WITH OE=1 AND OPx=1 Figure 36. PWM Signal from 0% to 100% Duty Cycle fCOUNTER ATR= FFDh COUNTER PWMx OUTPUT WITH MOD00=1 AND OPx=0 FFDh FFEh FFFh FFDh FFEh FFFh FFDh FFEh DCRx=000h DCRx=FFDh DCRx=FFEh PWMx OUTPUT WITH MOD00=1 AND OPx=1 DCRx=000h t 55/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.2 Dead Time Generation A dead time can be inserted between PWM0 and PWM1 using the DTGR register. This is required for half-bridge driving where PWM signals must not be overlapped. The non-overlapping PWM0/ PWM1 signals are generated through a programmable dead time by setting the DTE bit. Dead time value = DT[6:0] x Tcounter1 DTGR[7:0] is buffered inside so as to avoid deforming the current PWM cycle. The DTGR effect will take place only after an overflow. Figure 37. Dead Time Generation Tcounter1 Notes: 1. Dead time is generated only when DTE = 1 and DT[6:0] 0. If DTE is set and DT[6:0] = 0, PWM output signals will be at their reset state. 2. Half-bridge driving is possible only if polarities of PWM0 and PWM1 are not inverted, that is, if OP0 and OP1 are not set. If polarity is inverted, overlapping PWM0/PWM1 signals will be generated. 3. Dead Time generation does not work at 1ms timebase. CK_CNTR1 CNTR1 DCR0 DCR0+1 OVF ATR1 counter = DCR0 if DTE = 0 PWM 0 counter = DCR1 PWM 1 Tdt if DTE = 1 PWM 0 Tdt PWM 1 Tdt = DT[6:0] x Tcounter1 In the above example, when the DTE bit is set: - PWM goes low at DCR0 match and goes high at ATR1 + Tdt - PWM1 goes high at DCR0 + Tdt and goes low at ATR match. With this programmable delay (Tdt), the PWM0 and PWM1 signals which are generated are not overlapped. 56/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.3 Break Function The break function can be used to perform an emergency shutdown of the application being driven by the PWM signals. The break function is activated by the external BREAK pin. In order to use the break function it must be previously enabled by software setting the BPEN bit in the BREAKCR register. The Break active level can be programmed by the BREDGE bit in the BREAKCR register (in ROM devices the active level is not programmable; the break active level is low level). When an active level is detected on the BREAK pin, the BA bit is set and the break function is activated. In this case, the PWM signals are forced to BREAK value if the respective OEx bit is set in the PWMCR register. Software can set the BA bit to activate the break function without using the BREAK pin. The BREN1 and BREN2 bits in the BREAKEN Register are used to enable the break activation on the two counters respectively. In Dual Timer Mode, the break for PWM2 and PWM3 is enabled by the Figure 38. Block Diagram of Break Function BREDGE BREAKCR Register BREN2 bit. In Single Timer Mode, the BREN1 bit enables the break for all PWM channels. In ROM devices, BREN1 and BREN2 are both forced by hardware at high level and all PWMs are enabled. When a break function is activated (BA bit = 1 and BREN1/BREN2 = 1): - The break pattern (PWM[3:0] bits in the BREAKCR is forced directly on the PWMx output pins if respective OEx is set (after the inverter). - The 12-bit PWM counter CNTR1 is put to its reset value, that is 00h (if BREN1 = 1). - The 12-bit PWM counter CNTR2 is put to its reset value, that is 00h (if BREN2 = 1). - ATR1, ATR2, Preload and Active DCRx are put to their reset values. - Counters stop counting. When the break function is deactivated after applying the break (BA bit goes from 1 to 0 by software), the Timer takes the control of the PWM ports. BREAK pin Level Selection BREAKCR Register BA BPEN PWM3 PWM2 PWM1 PWM0 OEx PWM0 PWM1 (Inverters) PWM0 PWM1 PWM2 PWM3 BREAKEN Register PWM2 PWM3 PWM0/1 Break Enable PWM2/3 Break Enable ENCNTR2 bit BREN2 BREN1 57/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.4 Output Compare Mode To use this function, load a 12-bit value in the Preload DCRxH and DCRxL registers. When the 12-bit upcounter CNTR1 reaches the value stored in the Active DCRxH and DCRxL registers, the CMPFx bit in the PWMxCSR register is set and an interrupt request is generated if the CMPIE bit is set. In Single Timer mode the output compare function is performed only on CNTR1. The difference between both the modes is that in Single Timer mode, CNTR1 can be compared with any of the four DCR registers, and in Dual Timer mode, CNTR1 is compared with DCR0 or DCR1 and CNTR2 is compared with DCR2 or DCR3. In ROM devices, the CNTR2 counter is not used for this comparison. Notes: 1. The output compare function is only available for DCRx values other than 0 (reset value). 2. Duty cycle registers are buffered internally. The CPU writes in Preload Duty Cycle Registers and these values are transferred to Active Duty Cycle Registers after an overflow event if the corresponding transfer bit (TRANx bit) is set. Output compare is done by comparing these active DCRx values with the counters. Figure 39. Block Diagram of Output Compare Mode (Single Timer) DCRx PRELOAD DUTY CYCLE REG0/1/2/3 (ATCSR2) TRAN1 (ATCSR) OVF ACTIVE DUTY CYCLE REGx CNTR1 COUNTER 1 OUTPUT COMPARE CIRCUIT CMP INTERRUPT REQUEST CMPFx (PWMxCSR) CMPIE (ATCSR) 58/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.5 Input Capture Mode The 12-bit ATICR register is used to latch the value of the 12-bit free running upcounter CNTR1 after a rising or falling edge is detected on the ATIC pin. When an input capture occurs, the ICF bit is set and the ATICR register contains the value of the free running upcounter. An IC interrupt is genFigure 40. Block Diagram of Input Capture Mode erated if the ICIE bit is set. The ICF bit is reset by reading the ATICRH/ATICRL register when the ICF bit is set. The ATICR is a read only register and always contains the free running upcounter value which corresponds to the most recent input capture. Any further input capture is inhibited while the ICF bit is set. ATIC ATICR ATCSR 12-bit INPUT CAPTURE REGISTER IC INTERRUPT REQUEST ICF ICIE CK1 CK0 fLTIMER (1ms timebase @ 8 MHz) fCPU OFF 12-bit UPCOUNTER1 CNTR1 ATR1 12-bit AUTORELOAD REGISTER Figure 41. Input Capture Timing Diagram fCOUNTER COUNTER1 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah ATIC PIN INTERRUPT ICF FLAG xxh 04h 09h ATICR READ INTERRUPT t 59/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) Long Input Capture Pulses that last more than 8s can be measured with an accuracy of 4s if fOSC = 8 MHz under the following conditions: - The 12-bit AT4 Timer is clocked by the Lite Timer (RTC pulse: CK[1:0] = 01 in the ATCSR register) - The ICS bit in the ATCSR2 register is set so that the LTIC pin is used to trigger the AT4 Timer capture. - The signal to be captured is connected to LTIC pin - Input Capture registers LTICR, ATICRH and ATICRL are read This configuration allows to cascade the Lite Timer and the 12-bit AT4 Timer to get a 20-bit input capture value. Refer to Figure 42. Figure 42. Long Range Input Capture Block Diagram LTICR 8-bit Input Capture Register 8 LSB bits fOSC/32 8-bit Timebase Counter1 LITE TIMER 12-bit ARTIMER ATR1 12-bit AutoReload Register 20 cascaded bits fLTIMER ICS LTIC 1 CNTR1 12-bit Upcounter1 fcpu OFF ATICR 12-bit Input Capture Register ATIC 0 12 MSB bits Notes: 1. Since the input capture flags (ICF) for both timers (AT4 Timer and LT Timer) are set when signal transition occurs, software must mask one interrupt by clearing the corresponding ICIE bit before setting the ICS bit. 2. If the ICS bit changes (from 0 to 1 or from 1 to 0), a spurious transition might occur on the input capture signal because of different values on LTIC and ATIC. To avoid this situation, it is recommended to do the following: - First, reset both ICIE bits. - Then set the ICS bit. - Reset both ICF bits. - Finally, set the ICIE bit of desired interrupt. 3. How to compute a pulse length with long input capture feature: As both timers are used, computing a pulse length is not straight-forward. The procedure is as follows: - At the first input capture on the rising edge of the pulse, we assume that values in the registers are as follows: LTICR = LT1 ATICRH = ATH1 ATICRL = ATL1 Hence ATICR1 [11:0] = ATH1 & ATL1 Refer to Figure 43 on page 61. 60/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) - At the second input capture on the falling edge of the pulse, we assume that the values in the registers are as follows: LTICR = LT2 ATICRH = ATH2 ATICRL = ATL2 Hence ATICR2 [11:0] = ATH2 & ATL2 Now pulse width P between first capture and second capture will be: P = decimal (F9 - LT1 + LT2 + 1) * 0.004ms + decimal ((FFF * N) + N + ATICR2 - ATICR1 - 1) * 1ms where N = No of overflows of 12-bit CNTR1. Figure 43. Long Range Input Capture Timing Diagram fOSC/32 TB Counter1 F9h 00h LT1 F9h 00h ___ ___ ___ LT2 ___ ___ CNTR1 ___ ATH1 & ATL1 ___ ATH2 & ATL2 LTIC LTICR 00h LT1 LT2 ATICRH 0h ATH1 ATH2 ATICRL 00h ATL1 ATL2 ATICR = ATICRH[3:0] & ATICRL[7:0] 61/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.6 One Pulse Mode (available only on Flash devices) One Pulse mode can be used to control PWM2/3 signal with an external LTIC pin. This mode is available only in dual timer mode that is only for CNTR2, when the OP_EN bit in PWM3CSR register is set. One Pulse mode is activated by the external LTIC input. The active edge of the LTIC pin is selected by the OPEDGE bit in the PWM3CSR register. After obtaining the active edge of the LTIC pin, CNTR2 is reset (000h) and PWM3 is set to high. CNTR2 starts counting from 000h and when it reaches the active DCR3 value, PWM3 goes low. Until this time, any further transitions on the LTIC signal will have no effect. If there are LTIC transitions after CNTR2 reaches the DCR3 value, CNTR2 is reset again and PWM3 goes high. If there are no more LTIC active edges after the first active edge, CNTR2 counts until it reaches the ARR2 value, it is then reset and PWM3 is set to high. The counter again starts counting from 000h. When it reaches the active DCR3 value, PWM3 goes low, after which the counter counts until it reaches ARR2, it is reset and PWM3 is set to high again, and the cycle continues in this manner. The same operation applies for PWM2, but in this case the comparison is done on DCR2 OP_EN and OPEDGE bits take effect on the fly and are not synchronized with the Counter 2 overflow. The output bit OP2/3 can be used to invert the polarity of PWM2/3 in One Pulse mode. The update of these bits (OP2/3) is synchronized with the Counter 2 overflow, provided the TRAN2 bit is set. Notes: 1. The time taken from activation of LTIC input and CNTR2 reset is between 1 and 2 tCPU cycles, that is 125n to 250ns (with 8 MHz fCPU). 2. To avoid spurious interrupts, the LiteTimer input capture interrupt should be disabled while 12-bit ARTimer is in One Pulse mode. 3. Priority of various conditions is as follows for PWM3: Break > One Pulse mode with active LTIC edge > Forced overflow by s/w > One Pulse mode without active LTIC edge > normal PWM operation. 4. It is possible to update DCR2/3 and OP2/3 at the Counter 2 reset because the update is synchronized with the counter reset. This is managed by the overflow interrupt which is generated if the counter is reset either due to ARR match or active pulse at LTIC pin. 5. DCR2/3 and OP2/3 update in One Pulse mode is done dynamically using force update in software. 6. DCR3 update in this mode is not synchronized with any event. That may lead to a longer next PWM3 cycle duration than expected just after the change (refer to Figure 46). 7. In One Pulse mode, the ATR2 value must be greater than the DCR2/3 value for PWM2/3 (opposite to normal PWM mode). 8. If there is an active edge on the LTIC pin after the counter has reset due to an ARR2 match, then the timer again is reset and appears as modified Duty cycle, depending on whether the new DCR value is less than or more than the previous value. 9. The TRAN2 bit should be set along with the FORCE2 bit with the same instruction after a write to the DCR register. 10. ARR2 value should be changed after an overflow in One Pulse mode to avoid any irregular PWM cycle. 11. When exiting from One Pulse mode, the OP_EN bit in the PWM3CSR register should be reset first and then the ENCNTR2 bit (if Counter 2 must be stopped). How to enter One Pulse mode: 1. Load ATR2H/ATR2L with required value. 2. Load DCR3H/DCR3L for PWM3. ATR2 value must be greater than DCR3. 3. Set OP3 in PWM3CSR if polarity change is required. 4. Select CNTR2 by setting ENCNTR2 bit in ATCSR2. 5. Set TRAN2 bit in ATCSR2 to enable transfer. 6. "Wait for Overflow" by checking the OVF2 flag in ATCSR2. 7. Select counter clock using CK<1:0> bits in ATCSR. 8. Set OP_EN bit in PWM3CSR to enable One Pulse mode. 9. Enable PWM3 by OE3 bit of PWMCR. The "Wait for Overflow" in step 6 can be replaced by forced update. Follow the same procedure for PWM2 with the bits corresponding to PWM2. Note: When break is applied in One Pulse mode, DUAL 12-BIT AUTORELOAD TIMER 4, CNTR2, DCR2/3 and ATR2 registers are reset. Conse- 62/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) quently, these registers must be initialized again when break is removed. Figure 44. Block Diagram of One Pulse Mode LTIC pin Edge Selection 12-bit Upcounter 2 PWM Generation OPEDGE OP_EN PWM3CSR Register 12-bit AutoReload Register 2 12-bit Active DCR2/3 PWM2/3 OP2/3 Figure 45. One Pulse Mode Timing Diagram OP_EN = 1 fcounter2 CNTR2 LTIC 000 DCR2/3 000 DCR2/3 ATR2 000 PWM2/3 OP_EN = 0 fcounter2 CNTR2 LTIC PWM2/3 OVF ATR2 DCR2/3 OVF ATR2 DCR2/3 OVF ATR2 Figure 46. Dynamic DCR2/3 update in One Pulse Mode fcounter2 CNTR2 LTIC 000 FFF (DCR3)old (DCR3)new ATR2 000 OP_EN = 1 FORCE2 TRAN2 DCR2/3 (DCR2/3)old (DCR2/3)new PWM2/3 extra PWM3 period due to DCR3 update dynamically in One Pulse mode. 63/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.3.7 Force Update (available only on Flash devices) In order not to wait for the counterx overflow to load the value into active DCRx registers, a programmable counterx overflow is provided. For both counters, a separate bit is provided which when set, starts the counters with the overflow value, that is FFFh. After overflow, the counters start counting from their respective autoreload register values. Figure 47. Force Overflow Timing Diagram These bits are FORCE1 and FORCE2 in the ATCSR2 register. FORCE1 is used to force an overflow on Counter 1 and FORCE2 is used for Counter 2. These bits are set by software and reset by hardware after the respective counter overflow event has occurred. This feature can be used at any time. All related features such as PWM generation, Output Compare, Input Capture and One Pulse can be used this way. fCNTRx FORCEx CNTRx E03 E04 FFF ARRx FORCE2 FORCE1 ATCSR2 Register 11.2.4 Low Power Modes Mode WAIT HALT Description No effect on AT timer AT timer halted 11.2.5 Interrupts Interrupt Event Overflow Event AT4 IC Event CMP Event Overflow Event2 Event Flag OVF1 ICF CMPFx OVF2 Enable Control Bit OVFIE1 ICIE Yes CMPIE OVFIE2 No No Exit from Wait Exit from Halt Exit from Active Halt Yes Note: The CMP and AT4 IC events are connected to the same interrupt vector. The OVF event is mapped on a separate vector (see Interrupts chap- ter). They generate an interrupt if the enable bit is set in the ATCSR register and the interrupt mask in the CC register is reset (RIM instruction). 64/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) 11.2.6 Register Description TIMER CONTROL STATUS REGISTER (ATCSR) Read / Write Reset Value: 0x00 0000 (x0h) 7 0 ICF ICIE CK1 CK0 0 OVF1 OVFIE1 CMPIE Bit 1 = OVFIE1 Overflow Interrupt Enable This bit is read/write by software and cleared by hardware after a reset. 0: Overflow interrupt disabled. 1: Overflow interrupt enabled. Bit 7 = Reserved, must be kept cleared Bit 0 = CMPIE Compare Interrupt Enable This bit is read/write by software and cleared by hardware after a reset. It can be used to mask the interrupt generated when any of the CMPFx bit is set. 0: Output compare interrupt disabled. 1: Output Compare interrupt enabled. COUNTER REGISTER 1 HIGH (CNTR1H) Read only Reset Value: 0000 0000 (00h) 15 0 0 0 0 8 CNTR1_ CNTR1_ CNTR1_ CNTR1_ 11 10 9 8 Bit 6 = ICF Input Capture Flag This bit is set by hardware and cleared by software by reading the ATICR register (a read access to ATICRH or ATICRL will clear this flag). Writing to this bit does not change the bit value. 0: No input capture 1: An input capture has occurred Bit 5 = ICIE IC Interrupt Enable This bit is set and cleared by software. 0: Input capture interrupt disabled 1: Input capture interrupt enabled COUNTER REGISTER 1 LOW (CNTR1L) Read only Reset Value: 0000 0000 (00h) 7 0 Bits 4:3 = CK[1:0] Counter Clock Selection These bits are set and cleared by software and cleared by hardware after a reset. They select the clock frequency of the counter. Counter Clock Selection OFF fLTIMER (1ms timebase @ 8 MHz) fCPU CK1 0 0 1 CK0 0 1 0 CNTR1_ CNTR1_ CNTR1_ CNTR1_ CNTR1_ CNTR1_ CNTR1_ CNTR1_ 7 6 5 4 3 2 1 0 Bits 15:12 = Reserved, must be kept cleared Bit 2 = OVF1 Overflow Flag This bit is set by hardware and cleared by software by reading the ATCSR register. It indicates the transition of the counter CNTR1 from FFFh to ATR1 value. 0: No counter overflow occurred 1: Counter overflow occurred Bits 11:0 = CNTR1[11:0] Counter Value This 12-bit register is read by software and cleared by hardware after a reset. The counter CNTR1 increments continuously as soon as a counter clock is selected. To obtain the 12-bit value, software should read the counter value in two consecutive read operations. The CNTRH register can be incremented between the two reads, and in order to be accurate when fTIMER = fCPU, the software should take this into account when CNTRL and CNTRH are read. If CNTRL is close to its highest value, CNTRH could be incremented before it is read. When a counter overflow occurs, the counter restarts from the value specified in the ATR1 register. 65/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) AUTORELOAD REGISTER (ATR1H) Read / Write Reset Value: 0000 0000 (00h) 15 0 0 0 0 ATR11 ATR10 ATR9 8 7 ATR8 0 0 0 0 OP_EN OPEDGE OPx CMPFx 0 PWMx CONTROL STATUS REGISTER (PWMxCSR) Read / Write Reset Value: 0000 0000 (00h) AUTORELOAD REGISTER (ATR1L) Read / Write Reset Value: 0000 0000 (00h) 7 ATR7 ATR6 ATR5 ATR4 ATR3 ATR2 ATR1 0 ATR0 Bits 7:4 = Reserved, must be kept cleared Bit 3 = OP_EN One Pulse Mode Enable (not applicable to ROM devices) This bit is read/write by software and cleared by hardware after a reset. This bit enables the One Pulse feature for PWM2 and PWM3. (Only available for PWM3CSR) 0: One Pulse mode disable for PWM2/3. 1: One Pulse mode enable for PWM2/3. Bits 15:12 = Reserved, must be kept cleared Bits 11:0 = ATR1[11:0] Autoreload Register 1 This is a 12-bit register which is written by software. The ATR1 register value is automatically loaded into the upcounter CNTR1 when an overflow occurs. The register value is used to set the PWM frequency. Bit 2 = OPEDGE One Pulse Edge Selection (not applicable to ROM devices) This bit is read/write by software and cleared by hardware after a reset. This bit selects the polarity of the LTIC signal for One Pulse feature. This bit will be effective only if OP_EN bit is set. (Only available for PWM3CSR) 0: Falling edge of LTIC is selected. 1: Rising edge of LTIC is selected. PWM OUTPUT CONTROL REGISTER (PWMCR) Read/Write Reset Value: 0000 0000 (00h) 7 0 OE3 0 OE2 0 OE1 0 0 OE0 Bits 7:0 = OE[3:0] PWMx Output Enable. These bits are set and cleared by software and cleared by hardware after a reset. 0: PWM mode disabled. PWMx Output Alternate Function disabled (I/O pin free for general purpose I/O) 1: PWM mode enabled Bit 1 = OPx PWMx Output Polarity This bit is read/write by software and cleared by hardware after a reset. This bit selects the polarity of the PWM signal. 0: The PWM signal is not inverted. 1: The PWM signal is inverted. Bit 0 = CMPFx PWMx Compare Flag This bit is set by hardware and cleared by software by reading the PWMxCSR register. It indicates that the upcounter value matches the Active DCRx register value. 0: Upcounter value does not match DCRx value. 1: Upcounter value matches DCRx value. 66/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) BREAK CONTROL REGISTER (BREAKCR) Read/Write Reset Value: 0000 0000 (00h) 7 0 BREDGE BA BPEN PWM3 PWM2 15 0 0 0 0 0 8 DCR11 DCR10 DCR9 DCR8 PWM1 PWM0 PWMx DUTY CYCLE REGISTER LOW (DCRxL) Read / Write Reset Value: 0000 0000 (00h) 7 0 DCR2 DCR1 DCR0 Bit 7 = Reserved, must be kept cleared Bit 6 = BREDGE Break Input Edge Selection (not applicable to ROM devices) This bit is read/write by software and cleared by hardware after reset. It selects the active level of Break signal. 0: Low level of Break selected as active level. 1: High level of Break selected as active level. Bit 5 = BA Break Active This bit is read/write by software, cleared by hardware after reset and set by hardware when the BREAK pin is low. It activates/deactivates the Break function. 0: Break not active 1: Break active Bit 4 = BPEN Break Pin Enable This bit is read/write by software and cleared by hardware after Reset. 0: Break pin disabled 1: Break pin enabled Bits 3:0 = PWM[3:0] Break Pattern These bits are read/write by software and cleared by hardware after a reset. They are used to force the four PWMx output signals into a stable state when the Break function is active and corresponding OEx bit is set. PWMx DUTY CYCLE REGISTER HIGH (DCRxH) Read / Write Reset Value: 0000 0000 (00h) DCR7 DCR6 DCR5 DCR4 DCR3 Bits 15:12 = Reserved, must be kept cleared Bits 11:0 = DCRx[11:0] PWMx Duty Cycle Value This 12-bit value is written by software. It defines the duty cycle of the corresponding PWM output signal (see Figure 35). In PWM mode (OEx = 1 in the PWMCR register) the DCR[11:0] bits define the duty cycle of the PWMx output signal (see Figure 35). In Output Compare mode, they define the value to be compared with the 12-bit upcounter value. INPUT CAPTURE REGISTER HIGH (ATICRH) Read only Reset Value: 0000 0000 (00h) 15 0 0 0 0 ICR11 ICR10 ICR9 8 ICR8 INPUT CAPTURE REGISTER LOW (ATICRL) Read only Reset Value: 0000 0000 (00h) 7 ICR7 ICR6 ICR5 ICR4 ICR3 ICR2 ICR1 0 ICR0 Bits 15:12 = Reserved, must be kept cleared 67/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) Bits 11:0 = ICR[11:0] Input Capture Data This is a 12-bit register which is readable by software and cleared by hardware after a reset. The ATICR register contains the captured value of the 12-bit CNTR1 register when a rising or falling edge occurs on the ATIC or LTIC pin (depending on ICS). Capture will only be performed when the ICF flag is cleared. BREAK ENABLE REGISTER (BREAKEN) Read/Write Reset Value: 0000 0011 (03h) 7 0 0 0 0 0 0 ware one CPU clock cycle after Counter 2 overflow has occurred. 0: No effect on CNTR2 1: Loads FFFh in CNTR2 Note: This bit must not be reset by software Bit 6 = FORCE1 Force Counter 1 Overflow (forced at high level in ROM devices) This bit is read/set by software. When set, it loads FFFh in CNTR1 register. It is reset by hardware one CPU clock cycle after Counter 1 overflow has occurred. 0: No effect on CNTR1 1: Loads FFFh in CNTR1 Note: This bit must not be reset by software 0 BREN2 BREN1 Bits 7:2 = Reserved, must be kept cleared Bit 1 = BREN2 Break Enable for Counter 2 (forced at high level in ROM devices) This bit is read/write by software. It enables the break functionality for Counter 2 if BA bit is set in BREAKCR. It controls PWM2/3 if ENCNTR2 bit is set. 0: No Break applied for CNTR2 1: Break applied for CNTR2 Bit 0 = BREN1 Break Enable for Counter 1 (forced at high level in ROM devices) This bit is read/write by software. It enables the break functionality for Counter 1. If BA bit is set, it controls PWM0/1 by default, and controls PWM2/3 also if ENCNTR2 bit is reset. 0: No Break applied for CNTR1 1: Break applied for CNTR1 TIMER CONTROL REGISTER2 (ATCSR2) Read/Write Reset Value: 0000 0011 (03h) 7 FORCE FORCE 2 1 ICS OVFIE2 OVF2 Bit 5 = ICS Input Capture Shorted This bit is read/write by software. It allows the ATtimer CNTR1 to use the LTIC pin for long input capture. 0: ATIC for CNTR1 input capture 1: LTIC for CNTR1 input capture Bit 4 = OVFIE2 Overflow Interrupt 2 Enable This bit is read/write by software and controls the overflow interrupt of Counter 2. 0: Overflow interrupt disabled 1: Overflow interrupt enabled Bit 3 = OVF2 Overflow Flag This bit is set by hardware and cleared by software by reading the ATCSR2 register. It indicates the transition of the Counter 2 from FFFh to ATR2 value. 0: No counter overflow occurred 1: Counter overflow occurred Bit 2 = ENCNTR2 Enable Counter 2 for PWM2/3 This bit is read/write by software and switches the PWM2/3 operation to the CNTR2 counter. If this bit is set, PWM2/3 will be generated using CNTR2. 0: PWM2/3 is generated using CNTR1. 1: PWM2/3 is generated using CNTR2. Note: Counter 2 becomes frozen when the ENCNTR2 bit is reset. When ENCNTR2 is set again, the counter will restart from the last value. 0 ENCNT TRAN2 TRAN1 R2 Bit 7 = FORCE2 Force Counter 2 Overflow (not applicable to ROM devices) This bit is read/set by software. When set, it loads FFFh in the CNTR2 register. It is reset by hard- 68/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 4 (cont'd) Bit 1 = TRAN2 Transfer Enable 2 This bit is read/write by software, cleared by hardware after each completed transfer and set by hardware after reset. It controls the transfers on CNTR2. It allows the value of the Preload DCRx registers to be transferred to the Active DCRx registers after the next overflow event. The OPx bits are transferred to the shadow OPx bits in the same way. Notes: 1. DCR2/3 transfer is controlled using this bit if ENCNTR2 bit is set. 2. This bit must not be reset by software. Bit 0 = TRAN1 Transfer Enable 1 This bit is read/write by software, cleared by hardware after each completed transfer and set by hardware after reset. It controls the transfers on CNTR1. It allows the value of the Preload DCRx registers to be transferred to the Active DCRx registers after the next overflow event. The OPx bits are transferred to the shadow OPx bits in the same way. Notes: 1. DCR0,1 transfers are always controlled using this bit. 2. DCR2/3 transfer is controlled using this bit if ENCNTR2 is reset. 3.This bit must not be reset by software AUTORELOAD REGISTER2 (ATR2H) Read / Write Reset Value: 0000 0000 (00h) 15 0 0 0 0 ATR11 ATR10 ATR9 8 ATR8 Bits 11:0 = ATR2[11:0] Autoreload Register 2 This is a 12-bit register which is written by software. The ATR2 register value is automatically loaded into the upcounter CNTR2 when an overflow of CNTR2 occurs. The register value is used to set the PWM2/PWM3 frequency when ENCNTR2 is set. DEAD TIME GENERATOR REGISTER (DTGR) Read/Write Reset Value: 0000 0000 (00h) 7 DTE DT6 DT5 DT4 DT3 DT2 DT1 0 DT0 Bit 7 = DTE Dead Time Enable This bit is read/write by software. It enables a dead time generation on PWM0/PWM1. 0: No Dead time insertion. 1: Dead time insertion enabled. Bits 6:0 = DT[6:0] Dead Time Value These bits are read/write by software. They define the dead time inserted between PWM0/PWM1. Dead time is calculated as follows: Dead Time = DT[6:0] x Tcounter1 Note: 1. If DTE is set and DT[6:0] = 0, PWM output signals are at their reset state. AUTORELOAD REGISTER2 (ATR2L) Read / Write Reset Value: 0000 0000 (00h) 7 ATR7 ATR6 ATR5 ATR4 ATR3 ATR2 ATR1 0 ATR0 Bits 15:12 = Reserved, must be kept cleared 69/138 1 ST7L15, ST7L19 DUAL 12-BIT AUTORELOAD TIMER 3 (cont'd) Table 14. Register Map and Reset Values Address (Hex.) 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 Register Label ATCSR Reset Value CNTR1H Reset Value 7 0 0 6 ICF 0 0 5 ICIE 0 0 4 CK1 0 0 3 CK0 0 2 OVF1 0 1 OVFIE1 0 0 CMPIE 0 CNTR1_11 CNTR1_10 CNTR1_9 CNTR1_8 0 0 0 0 CNTR1_2 CNTR1_1 CNTR1_0 0 0 0 ATR10 0 ATR2 0 OE1 0 0 0 0 OPEDGE 0 DCR10 0 DCR2 0 DCR10 0 DCR2 0 DCR10 0 DCR2 0 DCR10 0 DCR2 0 ICR10 0 ICR2 0 ATR9 0 ATR1 0 0 OP0 0 OP1 0 OP2 0 OP3 0 DCR9 0 DCR1 0 DCR9 0 DCR1 0 DCR9 0 DCR1 0 DCR9 0 DCR1 0 ICR9 0 ICR1 0 ATR8 0 ATR0 0 OE0 0 CMPF0 0 CMPF1 0 CMPF2 0 CMPF3 0 DCR8 0 DCR0 0 DCR8 0 DCR0 0 DCR8 0 DCR0 0 DCR8 0 DCR0 0 ICR8 0 ICR0 0 CNTR1L CNTR1_7 CNTR1_8 CNTR1_7 CNTR1_6 CNTR1_3 Reset Value 0 0 0 0 0 ATR1H Reset Value ATR1L Reset Value PWMCR Reset Value PWM0CSR Reset Value PWM1CSR Reset Value PWM2CSR Reset Value PWM3CSR Reset Value DCR0H Reset Value DCR0L Reset Value DCR1H Reset Value DCR1L Reset Value DCR2H Reset Value DCR2L Reset Value DCR3H Reset Value DCR3L Reset Value ATICRH Reset Value ATICRL Reset Value 0 ATR7 0 0 0 0 0 0 0 DCR7 0 0 DCR7 0 0 DCR7 0 0 DCR7 0 0 ICR7 0 0 ATR6 0 OE3 0 0 0 0 0 0 DCR6 0 0 DCR6 0 0 DCR6 0 0 DCR6 0 0 ICR6 0 0 ATR5 0 0 0 0 0 0 0 DCR5 0 0 DCR5 0 0 DCR5 0 0 DCR5 0 0 ICR5 0 0 ATR4 0 OE2 0 0 0 0 0 0 DCR4 0 0 DCR4 0 0 DCR4 0 0 DCR4 0 0 ICR4 0 ATR11 0 ATR3 0 0 0 0 0 OP_EN 0 DCR11 0 DCR3 0 DCR11 0 DCR3 0 DCR11 0 DCR3 0 DCR11 0 DCR3 0 ICR11 0 ICR3 0 70/138 1 ST7L15, ST7L19 Address (Hex.) 21 22 23 24 25 26 Register Label 7 6 5 ICS 0 BA 0 0 ATR5 0 DT5 0 0 4 OVFIE2 0 BPEN 0 0 ATR4 0 DT4 0 0 3 OVF2 0 PWM3 0 ATR11 0 ATR3 0 DT3 0 0 2 ENCNTR2 0 PWM2 0 ATR10 0 ATR2 0 DT2 0 0 1 TRAN2 1 PWM1 0 ATR9 0 ATR1 0 DT1 0 BREN2 1 0 TRAN1 1 PWM0 0 ATR8 0 ATR0 0 DT0 0 BREN1 1 ATCSR2 FORCE2 FORCE1 Reset Value 0 0 BREAKCR Reset Value ATR2H Reset Value ATR2L Reset Value DTGR Reset Value BREAKEN Reset Value BRSEL 0 0 ATR7 0 DTE 0 0 BREDGE 0 0 ATR6 0 DT6 0 0 71/138 1 ST7L15, ST7L19 11.3 LITE TIMER 2 (LT2) 11.3.1 Introduction The Lite Timer can be used for general-purpose timing functions. It is based on two free-running 8bit upcounters and an 8-bit input capture register. 11.3.2 Main Features Realtime Clock - One 8-bit upcounter 1ms or 2ms timebase period (@ 8 MHz fOSC) Figure 48. Lite Timer 2 Block Diagram fOSC/32 LTCNTR 8-bit TIMEBASE COUNTER 2 LTCSR2 0 0 0 0 0 0 TB2IE TB2F - One 8-bit upcounter with autoreload and programmable timebase period from 4s to 1.024ms in 4s increments (@ 8 MHz fOSC) - 2 Maskable timebase interrupts Input Capture - 8-bit input capture register (LTICR) - Maskable interrupt with wake-up from Halt mode capability LTTB2 Interrupt request 8 LTARR 8-bit AUTORELOAD REGISTER fLTIMER To 12-bit AT TImer /2 8-bit TIMEBASE COUNTER 1 fLTIMER 1 0 Timebase 1 or 2 ms (@ 8 MHz fOSC) 8 LTICR LTIC 8-bit INPUT CAPTURE REGISTER LTCSR1 ICIE ICF TB TB1IE TB1F LTTB1 INTERRUPT REQUEST LTIC INTERRUPT REQUEST 72/138 1 ST7L15, ST7L19 LITE TIMER (cont'd) 11.3.3 Functional Description 11.3.3.1 Timebase Counter 1 The 8-bit value of Counter 1 cannot be read or written by software. After an MCU reset, it starts incrementing from 0 at a frequency of fOSC/32. An overflow event occurs when the counter rolls over from F9h to 00h. If fOSC = 8 MHz, then the time period between two counter overflow events is 1 ms. This period can be doubled by setting the TB bit in the LTCSR1 register. When Counter 1 overflows, the TB1F bit is set by hardware and an interrupt request is generated if the TB1IE bit is set. The TB1F bit is cleared by software reading the LTCSR1 register. 11.3.3.2 Input Capture The 8-bit input capture register is used to latch the free-running upcounter (Counter 1) 1 after a rising or falling edge is detected on the LTIC pin. When an input capture occurs, the ICF bit is set and the LTICR1 register contains the MSB of Counter 1. Figure 49. Input Capture Timing Diagram. 4s (@ 8 MHz fOSC) fCPU fOSC/32 CLEARED BY S/W READING LTIC REGISTER An interrupt is generated if the ICIE bit is set. The ICF bit is cleared by reading the LTICR register. The LTICR is a read-only register and always contains the data from the last input capture. Input capture is inhibited if the ICF bit is set. 11.3.3.3 Timebase Counter 2 Counter 2 is an 8-bit autoreload upcounter. It can be read by accessing the LTCNTR register. After an MCU reset, it increments at a frequency of fOSC/32 starting from the value stored in the LTARR register. A counter overflow event occurs when the counter rolls over from FFh to the LTARR reload value. Software can write a new value at any time in the LTARR register, this value will be automatically loaded in the counter when the next overflow occurs. When Counter 2 overflows, the TB2F bit in the LTCSR2 register is set by hardware and an interrupt request is generated if the TB2IE bit is set. The TB2F bit is cleared by software reading the LTCSR2 register. 8-bit COUNTER 1 01h 02h 03h 04h 05h 06h 07h LTIC PIN ICF FLAG LTICR REGISTER xxh 04h 07h t 73/138 1 ST7L15, ST7L19 LITE TIMER (cont'd) 11.3.4 Low Power Modes Mode Description No effect on Lite timer SLOW (this peripheral is driven directly by fOSC/32) WAIT No effect on Lite timer ACTIVE HALT No effect on Lite timer HALT Lite timer stops counting 11.3.5 Interrupts Interrupt Event Enable Event Control Flag Bit TB1IE TB2IE ICIE Yes Exit from Wait Exit from Active Halt Yes No No No Exit from Halt reading the LTCSR register. Writing to this bit has no effect. 0: No Counter 2 overflow 1: A Counter 2 overflow has occurred LITE TIMER AUTORELOAD (LTARR) Read / Write Reset Value: 0000 0000 (00h) 7 AR7 AR7 AR7 AR7 AR3 AR2 AR1 REGISTER 0 AR0 Timebase 1 TB1F Event Timebase 2 TB2F Event IC Event ICF Bits 7:0 = AR[7:0] Counter 2 Reload Value These bits register is read/write by software. The LTARR value is automatically loaded into Counter 2 (LTCNTR) when an overflow occurs. LITE TIMER COUNTER 2 (LTCNTR) Read only Reset Value: 0000 0000 (00h) 7 CNT7 CNT7 CNT7 CNT7 CNT3 CNT2 CNT1 0 CNT0 Note: The TBxF and ICF interrupt events are connected to separate interrupt vectors (see Interrupts chapter). They generate an interrupt if the enable bit is set in the LTCSR1 or LTCSR2 register and the interrupt mask in the CC register is reset (RIM instruction). 11.3.6 Register Description LITE TIMER CONTROL/STATUS REGISTER 2 (LTCSR2) Read / Write Reset Value: 0000 0000 (00h) 7 0 0 0 0 0 0 TB2IE 0 TB2F Bits 7:0 = CNT[7:0] Counter 2 Reload Value This register is read by software. The LTARR value is automatically loaded into Counter 2 (LTCNTR) when an overflow occurs. LITE TIMER CONTROL/STATUS REGISTER (LTCSR1) Read / Write Reset Value: 0x00 0000 (x0h) 7 ICIE ICF TB TB1IE TB1F 0 - Bits 7:2 = Reserved, must be kept cleared. Bit 1 = TB2IE Timebase 2 Interrupt enable This bit is set and cleared by software. 0: Timebase (TB2) interrupt disabled 1: Timebase (TB2) interrupt enabled Bit 0 = TB2F Timebase 2 Interrupt Flag This bit is set by hardware and cleared by software Bit 7 = ICIE Interrupt Enable This bit is set and cleared by software. 0: Input Capture (IC) interrupt disabled 1: Input Capture (IC) interrupt enabled 74/138 1 ST7L15, ST7L19 LITE TIMER (cont'd) Bit 6 = ICF Input Capture Flag This bit is set by hardware and cleared by software by reading the LTICR register. Writing to this bit does not change the bit value. 0: No input capture 1: An input capture has occurred Note: After an MCU reset, software must initialize the ICF bit by reading the LTICR register Bit 5 = TB Timebase period selection This bit is set and cleared by software. 0: Timebase period = tOSC * 8000 (1ms @ 8 MHz) 1: Timebase period = tOSC * 16000 (2ms @ 8 MHz) Bit 4 = TB1IE Timebase Interrupt enable This bit is set and cleared by software. 0: Timebase (TB1) interrupt disabled 1: Timebase (TB1) interrupt enabled Bit 3 = TB1F Timebase Interrupt Flag This bit is set by hardware and cleared by software reading the LTCSR register. Writing to this bit has no effect. 0: No counter overflow 1: A counter overflow has occurred Bits 2:0 = Reserved LITE TIMER INPUT CAPTURE REGISTER (LTICR) Read only Reset Value: 0000 0000 (00h) 7 ICR7 ICR6 ICR5 ICR4 ICR3 ICR2 ICR1 0 ICR0 Bits 7:0 = ICR[7:0] Input Capture Value These bits are read by software and cleared by hardware after a reset. If the ICF bit in the LTCSR is cleared, the value of the 8-bit up-counter will be captured when a rising or falling edge occurs on the LTIC pin. Table 15. Lite Timer Register Map and Reset Values Address (Hex.) 08 09 0A 0B 0C Register Label LTCSR2 Reset Value LTARR Reset Value LTCNTR Reset Value LTCSR1 Reset Value LTICR Reset Value 7 0 AR7 0 CNT7 0 ICIE 0 ICR7 0 6 0 AR6 0 CNT6 0 ICF x ICR6 0 5 0 AR5 0 CNT5 0 TB 0 ICR5 0 4 0 AR4 0 CNT4 0 TB1IE 0 ICR4 0 3 0 AR3 0 CNT3 0 TB1F 0 ICR3 0 2 0 AR2 0 CNT2 0 0 ICR2 0 1 TB2IE 0 AR1 0 CNT1 0 0 ICR1 0 0 TB2F 0 AR0 0 CNT0 0 0 ICR0 0 75/138 1 ST7L15, ST7L19 ON-CHIP PERIPHERALS (cont'd) 11.4 SERIAL PERIPHERAL INTERFACE (SPI) 11.4.1 Introduction The Serial Peripheral Interface (SPI) allows fullduplex, synchronous, serial communication with external devices. An SPI system may consist of a master and one or more slaves or a system in which devices may be either masters or slaves. 11.4.2 Main Features Full duplex synchronous transfers (on three lines) Simplex synchronous transfers (on two lines) Master or slave operation 6 master mode frequencies (fCPU/4 max.) fCPU/2 max. slave mode frequency (see note) SS Management by software or hardware Programmable clock polarity and phase End of transfer interrupt flag Write collision, Master Mode Fault and Overrun flags Note: In slave mode, continuous transmission is not possible at maximum frequency due to the software overhead for clearing status flags and to initiate the next transmission sequence. 11.4.3 General Description Figure 50 on page 77 shows the serial peripheral interface (SPI) block diagram. There are three registers: - SPI Control Register (SPICR) - SPI Control/Status Register (SPICSR) - SPI Data Register (SPIDR) The SPI is connected to external devices through four pins: - MISO: Master In / Slave Out data - MOSI: Master Out / Slave In data - SCK: Serial Clock out by SPI masters and input by SPI slaves - SS: Slave select: This input signal acts as a `chip select' to let the SPI master communicate with slaves individually and to avoid contention on the data lines. Slave SS inputs can be driven by standard I/O ports on the master Device. 76/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (SPI) (cont'd) Figure 50. Serial Peripheral Interface Block Diagram Data/Address Bus SPIDR Read Read Buffer Interrupt request MOSI MISO 8-bit Shift Register 7 SPIF WCOL OVR MODF 0 SPICSR SOD SSM 0 SSI SOD bit Write SS SPI STATE CONTROL 7 SPIE 1 0 SCK SPICR 0 SPE SPR2 MSTR CPOL CPHA SPR1 SPR0 MASTER CONTROL SERIAL CLOCK GENERATOR SS 77/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.3.1 Functional Description A basic example of interconnections between a single master and a single slave is illustrated in Figure 51. The MOSI pins are connected together and the MISO pins are connected together. In this way data is transferred serially between master and slave (most significant bit first). The communication is always initiated by the master. When the master device transmits data to a slave device via MOSI pin, the slave device responds by sending data to the master device via Figure 51. Single Master/ Single Slave Application MASTER MSBit LSBit MISO MISO MSBit SLAVE LSBit the MISO pin. This implies full duplex communication with both data out and data in synchronized with the same clock signal (which is provided by the master device via the SCK pin). To use a single data line, the MISO and MOSI pins must be connected at each node (in this case only simplex communication is possible). Four possible data/clock timing relationships may be chosen (see Figure 54 on page 81) but master and slave must be programmed with the same timing mode. 8-bit SHIFT REGISTER 8-bit SHIFT REGISTER MOSI MOSI SPI CLOCK GENERATOR SCK SS +5V SCK SS Not used if SS is managed by software 78/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.3.2 Slave Select Management As an alternative to using the SS pin to control the Slave Select signal, the application can choose to manage the Slave Select signal by software. This is configured by the SSM bit in the SPICSR register (see Figure 53). In software management, the external SS pin is free for other application uses and the internal SS signal level is driven by writing to the SSI bit in the SPICSR register. In Master mode: - SS internal must be held high continuously In Slave Mode: There are two cases depending on the data/clock timing relationship (see Figure 52): If CPHA = 1 (data latched on second clock edge): - SS internal must be held low during the entire transmission. This implies that in single slave applications the SS pin either can be tied to VSS, or made free for standard I/O by managing the SS function by software (SSM = 1 and SSI = 0 in the in the SPICSR register) If CPHA = 0 (data latched on first clock edge): - SS internal must be held low during byte transmission and pulled high between each byte to allow the slave to write to the shift register. If SS is not pulled high, a Write Collision error will occur when the slave writes to the shift register (see Section 11.4.5.3). Figure 52. Generic SS Timing Diagram MOSI/MISO Master SS Slave SS (if CPHA = 0) Slave SS (if CPHA = 1) Byte 1 Byte 2 Byte 3 Figure 53. Hardware/Software Slave Select Management SSM bit SSI bit SS external pin 1 0 SS internal 79/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.3.3 Master Mode Operation In master mode, the serial clock is output on the SCK pin. The clock frequency, polarity and phase are configured by software (refer to the description of the SPICSR register). Note: The idle state of SCK must correspond to the polarity selected in the SPICSR register (by pulling up SCK if CPOL = 1 or pulling down SCK if CPOL = 0). How to operate the SPI in master mode To operate the SPI in master mode, perform the following steps in order: 1. Write to the SPICR register: - Select the clock frequency by configuring the SPR[2:0] bits. - Select the clock polarity and clock phase by configuring the CPOL and CPHA bits. Figure 54 shows the four possible configurations. Note: The slave must have the same CPOL and CPHA settings as the master. 2. Write to the SPICSR register: - Either set the SSM bit and set the SSI bit or clear the SSM bit and tie the SS pin high for the complete byte transmit sequence. 3. Write to the SPICR register: - Set the MSTR and SPE bits Note: MSTR and SPE bits remain set only if SS is high). Important note: if the SPICSR register is not written first, the SPICR register setting (MSTR bit) may be not taken into account. The transmit sequence begins when software writes a byte in the SPIDR register. 11.4.3.4 Master Mode Transmit Sequence When software writes to the SPIDR register, the data byte is loaded into the 8-bit shift register and then shifted out serially to the MOSI pin most significant bit first. When data transfer is complete: - The SPIF bit is set by hardware. - An interrupt request is generated if the SPIE bit is set and the interrupt mask in the CCR register is cleared. Clearing the SPIF bit is performed by the following software sequence: 1. An access to the SPICSR register while the SPIF bit is set 2. A read to the SPIDR register Note: While the SPIF bit is set, all writes to the SPIDR register are inhibited until the SPICSR register is read. 11.4.3.5 Slave Mode Operation In slave mode, the serial clock is received on the SCK pin from the master device. To operate the SPI in slave mode: 1. Write to the SPICSR register to perform the following actions: - Select the clock polarity and clock phase by configuring the CPOL and CPHA bits (see Figure 54). Note: The slave must have the same CPOL and CPHA settings as the master. - Manage the SS pin as described in Section 11.4.3.2 and Figure 52. If CPHA = 1 SS must be held low continuously. If CPHA = 0 SS must be held low during byte transmission and pulled up between each byte to let the slave write in the shift register. 2. Write to the SPICR register to clear the MSTR bit and set the SPE bit to enable the SPI I/O functions. 11.4.3.6 Slave Mode Transmit Sequence When software writes to the SPIDR register, the data byte is loaded into the 8-bit shift register and then shifted out serially to the MISO pin most significant bit first. The transmit sequence begins when the slave device receives the clock signal and the most significant bit of the data on its MOSI pin. When data transfer is complete: - The SPIF bit is set by hardware. - An interrupt request is generated if SPIE bit is set and interrupt mask in the CCR register is cleared. Clearing the SPIF bit is performed by the following software sequence: 1. An access to the SPICSR register while the SPIF bit is set 2. A write or a read to the SPIDR register Notes: While the SPIF bit is set, all writes to the SPIDR register are inhibited until the SPICSR register is read. The SPIF bit can be cleared during a second transmission; however, it must be cleared before the second SPIF bit in order to prevent an Overrun condition (see Section 11.4.5.2). 80/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.4 Clock Phase and Clock Polarity Four possible timing relationships may be chosen by software, using the CPOL and CPHA bits (See Figure 54). Note: The idle state of SCK must correspond to the polarity selected in the SPICSR register (by pulling up SCK if CPOL = 1 or pulling down SCK if CPOL = 0). The combination of the CPOL clock polarity and CPHA (clock phase) bits selects the data capture clock edge. Figure 54. Data Clock Timing Diagram CPHA = 1 SCK (CPOL = 1) SCK (CPOL = 0) Figure 54 shows an SPI transfer with the four combinations of the CPHA and CPOL bits. The diagram may be interpreted as a master or slave timing diagram where the SCK pin, the MISO pin and the MOSI pin are directly connected between the master and the slave device. Note: If CPOL is changed at the communication byte boundaries, the SPI must be disabled by resetting the SPE bit. MISO (from master) MOSI (from slave) SS (to slave) CAPTURE STROBE MSBit Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 LSBit MSBit Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 LSBit CPHA = 0 SCK (CPOL = 1) SCK (CPOL = 0) MISO (from master) MOSI (from slave) SS (to slave) CAPTURE STROBE MSBit Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 LSBit MSBit Bit 6 Bit 5 Bit 4 Bit3 Bit 2 Bit 1 LSBit Note: This figure should not be used as a replacement for parametric information. Refer to the Electrical Characteristics chapter. 81/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.5 Error Flags 11.4.5.1 Master Mode Fault (MODF) Master mode fault occurs when the master device's SS pin is pulled low. When a Master mode fault occurs: - The MODF bit is set and an SPI interrupt request is generated if the SPIE bit is set. - The SPE bit is reset. This blocks all output from the device and disables the SPI peripheral. - The MSTR bit is reset, thus forcing the device into slave mode. Clearing the MODF bit is done through a software sequence: 1. A read access to the SPICSR register while the MODF bit is set. 2. A write to the SPICR register. Notes: To avoid any conflicts in an application with multiple slaves, the SS pin must be pulled high during the MODF bit clearing sequence. The SPE and MSTR bits may be restored to their original state during or after this clearing sequence. Hardware does not allow the user to set the SPE and MSTR bits while the MODF bit is set except in the MODF bit clearing sequence. In a slave device, the MODF bit can not be set, but in a multimaster configuration the device can be in slave mode with the MODF bit set. The MODF bit indicates that there might have been a multimaster conflict and allows software to handle this using an interrupt routine and either perform a reset or return to an application default state. 11.4.5.2 Overrun Condition (OVR) An overrun condition occurs when the master device has sent a data byte and the slave device has not cleared the SPIF bit issued from the previously transmitted byte. When an Overrun occurs: - The OVR bit is set and an interrupt request is generated if the SPIE bit is set. In this case, the receiver buffer contains the byte sent after the SPIF bit was last cleared. A read to the SPIDR register returns this byte. All other bytes are lost. The OVR bit is cleared by reading the SPICSR register. 11.4.5.3 Write Collision Error (WCOL) A write collision occurs when the software tries to write to the SPIDR register while a data transfer is taking place with an external device. When this happens, the transfer continues uninterrupted and the software write will be unsuccessful. Write collisions can occur both in master and slave mode. See also Section 11.4.3.2 Slave Select Management. Note: A "read collision" will never occur since the received data byte is placed in a buffer in which access is always synchronous with the CPU operation. The WCOL bit in the SPICSR register is set if a write collision occurs. No SPI interrupt is generated when the WCOL bit is set (the WCOL bit is a status flag only). Clearing the WCOL bit is done through a software sequence (see Figure 55). Figure 55. Clearing the WCOL Bit (Write Collision Flag) Software Sequence Clearing sequence after SPIF = 1 (end of a data byte transfer) 1st Step Read SPICSR 2nd Step Read SPIDR RESULT SPIF = 0 WCOL = 0 Clearing sequence before SPIF = 1 (during a data byte transfer) 1st Step Read SPICSR RESULT 2nd Step Read SPIDR WCOL = 0 Note: Writing to the SPIDR register instead of reading it does not reset the WCOL bit. 82/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.5.4 Single Master and Multimaster Configurations There are two types of SPI systems: - Single Master System - Multimaster System Single Master System A typical single master system may be configured using a device as the master and four devices as slaves (see Figure 56). The master device selects the individual slave devices by using four pins of a parallel port to control the four SS pins of the slave devices. The SS pins are pulled high during reset since the master device ports will be forced to be inputs at that time, thus disabling the slave devices. Note: To prevent a bus conflict on the MISO line, the master allows only one active slave device during a transmission. For more security, the slave device may respond to the master with the received data byte. Then the master will receive the previous byte back from the slave device if all MISO and MOSI pins are connected and the slave has not written to its SPIDR register. Other transmission security methods can use ports for handshake lines or data bytes with command fields. Multimaster System A multimaster system may also be configured by the user. Transfer of master control could be implemented using a handshake method through the I/O ports or by an exchange of code messages through the serial peripheral interface system. The multimaster system is principally handled by the MSTR bit in the SPICR register and the MODF bit in the SPICSR register. Figure 56. Single Master / Multiple Slave Configuration SS SCK Slave Device MOSI MISO SCK Slave Device MOSI SS SCK Slave Device MOSI SS SCK Slave Device MOSI SS MISO MISO MISO MOSI MISO Ports SCK Master Device 5V SS 83/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.6 Low Power Modes Mode WAIT Description No effect on SPI. SPI interrupt events cause the device to exit from WAIT mode. SPI registers are frozen. In HALT mode, the SPI is inactive. SPI operation resumes when the device is woken up by an interrupt with "exit from HALT mode" capability. The data received is subsequently read from the SPIDR register when the software is running (interrupt vector fetching). If several data are received before the wakeup event, then an overrun error is generated. This error can be detected after the fetch of the interrupt routine that woke up the Device. HALT the SPI from HALT mode state to normal state. If the SPI exits from Slave mode, it returns to normal state immediately. Caution: The SPI can wake up the device from HALT mode only if the Slave Select signal (external SS pin or the SSI bit in the SPICSR register) is low when the device enters HALT mode. So, if Slave selection is configured as external (see Section 11.4.3.2), make sure the master drives a low level on the SS pin when the slave enters HALT mode. 11.4.7 Interrupts Interrupt Event SPI End of Transfer Event Master Mode Fault Event Overrun Error Event Flag SPIF MODF OVR SPIE Yes No Enable Control Bit Exit from Wait Exit from Halt Yes 11.4.6.1 Using the SPI to wake up the device from Halt mode In slave configuration, the SPI is able to wake up the device from HALT mode through a SPIF interrupt. The data received is subsequently read from the SPIDR register when the software is running (interrupt vector fetch). If multiple data transfers have been performed before software clears the SPIF bit, then the OVR bit is set by hardware. Note: When waking up from HALT mode, if the SPI remains in Slave mode, it is recommended to perform an extra communications cycle to bring Note: The SPI interrupt events are connected to the same interrupt vector (see Interrupts chapter). They generate an interrupt if the corresponding Enable Control Bit is set and the interrupt mask in the CC register is reset (RIM instruction). 84/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) 11.4.8 Register Description SPI CONTROL REGISTER (SPICR) Read/Write Reset Value: 0000 xxxx (0xh) 7 SPIE SPE SPR2 MSTR CPOL CPHA SPR1 0 SPR0 Bit 7 = SPIE Serial Peripheral Interrupt Enable This bit is set and cleared by software. 0: Interrupt is inhibited 1: An SPI interrupt is generated whenever an End of Transfer event, Master Mode Fault or Overrun error occurs (SPIF = 1, MODF = 1 or OVR = 1 in the SPICSR register) Bit 6 = SPE Serial Peripheral Output Enable This bit is set and cleared by software. It is also cleared by hardware when, in master mode, SS = 0 (see Section 11.4.5.1 Master Mode Fault (MODF)). The SPE bit is cleared by reset, so the SPI peripheral is not initially connected to the external pins. 0: I/O pins free for general purpose I/O 1: SPI I/O pin alternate functions enabled Bit 5 = SPR2 Divider Enable This bit is set and cleared by software and is cleared by reset. It is used with the SPR[1:0] bits to set the baud rate. Refer to Table 16 SPI Master Mode SCK Frequency. 0: Divider by 2 enabled 1: Divider by 2 disabled Note: This bit has no effect in slave mode. Bit 4 = MSTR Master Mode This bit is set and cleared by software. It is also cleared by hardware when, in master mode, SS = 0 (see Section 11.4.5.1 Master Mode Fault (MODF)). 0: Slave mode 1: Master mode. The function of the SCK pin changes from an input to an output and the functions of the MISO and MOSI pins are reversed. Bit 3 = CPOL Clock Polarity This bit is set and cleared by software. This bit determines the idle state of the serial Clock. The CPOL bit affects both the master and slave modes. 0: SCK pin has a low level idle state 1: SCK pin has a high level idle state Note: If CPOL is changed at the communication byte boundaries, the SPI must be disabled by resetting the SPE bit. Bit 2 = CPHA Clock Phase This bit is set and cleared by software. 0: The first clock transition is the first data capture edge. 1: The second clock transition is the first capture edge. Note: The slave must have the same CPOL and CPHA settings as the master. Bits 1:0 = SPR[1:0] Serial Clock Frequency These bits are set and cleared by software. Used with the SPR2 bit, they select the baud rate of the SPI serial clock SCK output by the SPI in master mode. Note: These 2 bits have no effect in slave mode. Table 16. SPI Master Mode SCK Frequency Serial Clock fCPU/4 fCPU/8 fCPU/16 fCPU/32 fCPU/64 fCPU/128 SPR2 1 0 1 0 1 0 SPR1 SPR0 0 1 0 1 85/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) SPI CONTROL/STATUS REGISTER (SPICSR) Read/Write (some bits Read Only) Reset Value: 0000 0000 (00h) 7 SPIF WCOL OVR MODF SOD SSM 0 SSI Bit 2 = SOD SPI Output Disable This bit is set and cleared by software. When set, it disables the alternate function of the SPI output (MOSI in master mode / MISO in slave mode) 0: SPI output enabled (if SPE = 1) 1: SPI output disabled Bit 1 = SSM SS Management This bit is set and cleared by software. When set, it disables the alternate function of the SPI SS pin and uses the SSI bit value instead. See Section 11.4.3.2 Slave Select Management. 0: Hardware management (SS managed by external pin) 1: Software management (internal SS signal controlled by SSI bit. External SS pin free for general-purpose I/O) Bit 0 = SSI SS Internal Mode This bit is set and cleared by software. It acts as a `chip select' by controlling the level of the SS slave select signal when the SSM bit is set. 0: Slave selected 1: Slave deselected SPI DATA I/O REGISTER (SPIDR) Read/Write Reset Value: Undefined 7 D7 D6 D5 D4 D3 D2 D1 0 D0 Bit 7 = SPIF Serial Peripheral Data Transfer Flag (Read only) This bit is set by hardware when a transfer has been completed. An interrupt is generated if SPIE = 1 in the SPICR register. It is cleared by a software sequence (an access to the SPICSR register followed by a write or a read to the SPIDR register). 0: Data transfer is in progress or the flag has been cleared. 1: Data transfer between the device and an external device has been completed. Note: While the SPIF bit is set, all writes to the SPIDR register are inhibited until the SPICSR register is read. Bit 6 = WCOL Write Collision status (Read only) This bit is set by hardware when a write to the SPIDR register is done during a transmit sequence. It is cleared by a software sequence (see Figure 55). 0: No write collision occurred 1: A write collision has been detected Bit 5 = OVR SPI Overrun error (Read only) This bit is set by hardware when the byte currently being received in the shift register is ready to be transferred into the SPIDR register while SPIF = 1 (See Section 11.4.5.2). An interrupt is generated if SPIE = 1 in the SPICR register. The OVR bit is cleared by software reading the SPICSR register. 0: No overrun error 1: Overrun error detected Bit 4 = MODF Mode Fault flag (Read only) This bit is set by hardware when the SS pin is pulled low in master mode (see Section 11.4.5.1 Master Mode Fault (MODF)). An SPI interrupt can be generated if SPIE = 1 in the SPICR register. This bit is cleared by a software sequence (An access to the SPICSR register while MODF = 1 followed by a write to the SPICR register). 0: No master mode fault detected 1: A fault in master mode has been detected Bit 3 = Reserved, must be kept cleared. The SPIDR register is used to transmit and receive data on the serial bus. In a master device, a write to this register will initiate transmission/reception of another byte. Notes: During the last clock cycle the SPIF bit is set, a copy of the received data byte in the shift register is moved to a buffer. When the user reads the serial peripheral data I/O register, the buffer is actually being read. While the SPIF bit is set, all writes to the SPIDR register are inhibited until the SPICSR register is read. Warning: A write to the SPIDR register places data directly into the shift register for transmission. A read to the SPIDR register returns the value located in the buffer and not the content of the shift register (see Figure 50). 86/138 1 ST7L15, ST7L19 SERIAL PERIPHERAL INTERFACE (cont'd) Table 17. SPI Register Map and Reset Values Address (Hex.) 0031h 0032h 0033h Register Label SPIDR Reset Value SPICR Reset Value SPICSR Reset Value 7 MSB x SPIE 0 SPIF 0 6 5 4 3 2 1 0 LSB x SPR0 x SSI 0 x SPE 0 WCOL 0 x SPR2 0 OVR 0 x MSTR 0 MODF 0 x CPOL x 0 x CPHA x SOD 0 x SPR1 x SSM 0 87/138 1 ST7L15, ST7L19 ON-CHIP PERIPHERALS (cont'd) 11.5 10-BIT A/D CONVERTER (ADC) 11.5.1 Introduction The on-chip Analog to Digital Converter (ADC) peripheral is a 10-bit, successive approximation converter with internal sample and hold circuitry. This peripheral has up to seven multiplexed analog input channels (refer to device pinout description) that allow the peripheral to convert the analog voltage levels from up to seven different sources. The result of the conversion is stored in a 10-bit Data Register. The A/D converter is controlled through a Control/Status Register. 11.5.2 Main Features 10-bit conversion Up to 7 channels with multiplexed input Linear successive approximation Figure 57. ADC Block Diagram DIV 4 Data register (DR) which contains the results Conversion complete status flag On/off bit (to reduce consumption) The block diagram is shown in Figure 57. 11.5.3 Functional Description 11.5.3.1 Analog Power Supply VDDA and VSSA are the high and low level reference voltage pins. In some devices (refer to device pinout description) they are internally connected to the VDD and VSS pins. Conversion accuracy may therefore be impacted by voltage drops and noise in the event of heavily loaded or badly decoupled power supply lines. fCPU 1 0 DIV 2 fADC 0 1 SLOW bit EOC SPEED ADON 0 0 CH2 CH1 CH0 ADCCSR 3 AIN0 AIN1 ANALOG MUX AIN6 RADC HOLD CONTROL ANALOG TO DIGITAL CONVERTER CADC ADCDRH D9 D8 D7 D6 D5 D4 D3 D2 ADCDRL 0 0 0 AMP AMP SLOW CAL SEL D1 D0 88/138 1 ST7L15, ST7L19 10-BIT A/D CONVERTER (ADC) (cont'd) 11.5.3.2 Digital A/D Conversion Result The conversion is monotonic, meaning that the result never decreases if the analog input does not and never increases if the analog input does not. If the input voltage (VAIN) is greater than VDDA (high-level voltage reference) then the conversion result is FFh in the ADCDRH register and 03h in the ADCDRL register (without overflow indication). If the input voltage (VAIN) is lower than VSSA (lowlevel voltage reference) then the conversion result in the ADCDRH and ADCDRL registers is 00 00h. The A/D converter is linear and the digital result of the conversion is stored in the ADCDRH and ADCDRL registers. The accuracy of the conversion is described in the Electrical Characteristics Section. RAIN is the maximum recommended impedance for an analog input signal. If the impedance is too high, this results in a loss of accuracy due to leakage and sampling not being completed in the alloted time. 11.5.3.3 A/D Conversion The analog input ports must be configured as input, no pull-up, no interrupt. Refer to the "I/O ports" chapter. Using these pins as analog inputs does not affect the ability of the port to be read as a logic input. In the ADCCSR register: - Select the CH[2:0] bits to assign the analog channel to convert. ADC Conversion mode In the ADCCSR register: Set the ADON bit to enable the A/D converter and to start the conversion. From this time on, the ADC performs a continuous conversion of the selected channel. When a conversion is complete: - The EOC bit is set by hardware. - The result is in the ADCDR registers. A read to the ADCDRH resets the EOC bit. To read the 10 bits, perform the following steps: 1. Poll the EOC bit 2. Read ADCDRL 3. Read ADCDRH. This clears EOC automatically. To read only 8 bits, perform the following steps: 1. Poll EOC bit 2. Read ADCDRH. This clears EOC automatically. 11.5.4 Low-Power Modes Note: The A/D converter may be disabled by resetting the ADON bit. This feature allows reduced power consumption when no conversion is needed and between single shot conversions. Mode WAIT Description No effect on A/D converter A/D Converter disabled. After wake-up from HALT mode, the A/D converter requires a stabilization time tSTAB (see Electrical Characteristics) before accurate conversions can be performed. HALT 11.5.5 Interrupts None. 89/138 1 ST7L15, ST7L19 10-BIT A/D CONVERTER (ADC) (cont'd) 11.5.6 Register Description CONTROL/STATUS REGISTER (ADCCSR) Read/Write (Except bit 7 read only) Reset Value: 0000 0000 (00h) 7 EOC SPEED ADON 0 0 CH2 CH1 DATA REGISTER HIGH (ADCDRH) Read Only Reset Value: xxxx xxxx (xxh) 0 CH0 7 D9 D8 D7 D6 D5 D4 D3 0 D2 Bit 7 = EOC End of Conversion This bit is set by hardware. It is cleared by software reading the ADCDRH register. 0: Conversion is not complete 1: Conversion complete Bit 6 = SPEED ADC clock selection This bit is set and cleared by software. It is used together with the SLOW bit to configure the ADC clock speed. Refer to the table in the SLOW bit description (ADCDRL register). Bit 5 = ADON A/D Converter on This bit is set and cleared by software. 0: A/D converter is switched off 1: A/D converter is switched on Bits 4:3 = Reserved (must be kept cleared) Bits 2:0 = CH[2:0] Channel Selection These bits are set and cleared by software. They select the analog input to convert. Channel Pin* AIN0 AIN1 AIN2 AIN3 AIN4 AIN5 AIN6 CH2 0 0 0 0 1 1 1 CH1 0 0 1 1 0 0 1 CH0 0 1 0 1 0 1 0 Bits 7:0 = D[9:2] MSB of Analog Converted Value AMP CONTROL/DATA REGISTER LOW (ADCDRL) Read/Write Reset Value: 0000 00xx (0xh) 7 0 0 0 SLOW D1 0 D0 Bits 7:5 = Reserved (forced by hardware to 0) Bit 4 = Reserved (must be kept cleared) Bit 3 = SLOW Slow mode This bit is set and cleared by software. It is used together with the SPEED bit in the ADCCSR register to configure the ADC clock speed as shown on the table below. fADC fCPU/2 fCPU fCPU/4 SLOW SPEED 0 0 0 1 1 x Note: Max fADC allowed = 4 MHz (see section 13.11 on page 122) Bit 2 = Reserved (must be kept cleared) Bits 1:0 = D[1:0] LSB of Analog Converted Value *The number of channels is device dependent. Refer to the device pinout description. 90/138 1 ST7L15, ST7L19 10-BIT A/D CONVERTER (ADC) (cont'd) Table 18. ADC Register Map and Reset Values Address (Hex.) 0034h 0035h 0036h Register Label ADCCSR Reset Value ADCDRH Reset Value ADCDRL Reset Value 7 EOC 0 D9 x 0 0 6 SPEED 0 D8 x 0 0 5 ADON 0 D7 x 0 0 4 0 0 D6 x AMPCAL 0 3 0 0 D5 x SLOW 0 2 CH2 0 D4 x AMPSEL 0 1 CH1 0 D3 x D1 x 0 CH0 0 D2 x D0 x 91/138 1 ST7L15, ST7L19 12 INSTRUCTION SET 12.1 ST7 ADDRESSING MODES The ST7 Core features 17 different addressing modes which can be classified in seven main groups: Addressing Mode Inherent Immediate Direct Indexed Indirect Relative Bit operation nop ld A,#$55 ld A,$55 ld A,($55,X) ld A,([$55],X) jrne loop bset byte,#5 Example The ST7 Instruction set is designed to minimize the number of bytes required per instruction: To do so, most of the addressing modes may be subdivided in two submodes called long and short: - Long addressing mode is more powerful because it can use the full 64 Kbyte address space, however it uses more bytes and more CPU cycles. - Short addressing mode is less powerful because it can generally only access page zero (0000h 00FFh range), but the instruction size is more compact, and faster. All memory to memory instructions use short addressing modes only (CLR, CPL, NEG, BSET, BRES, BTJT, BTJF, INC, DEC, RLC, RRC, SLL, SRL, SRA, SWAP) The ST7 Assembler optimizes the use of long and short addressing modes. Table 19. ST7 Addressing Mode Overview Mode Inherent Immediate Short Long No Offset Short Long Short Long Short Long Relative Relative Bit Bit Bit Direct Direct Direct Direct Direct Indirect Indirect Indirect Indirect Direct Indirect Direct Indirect Direct Relative Indexed Indexed Indexed Indexed Indexed nop ld A,#$55 ld A,$10 ld A,$1000 ld A,(X) ld A,($10,X) ld A,($1000,X) ld A,[$10] ld A,[$10.w] ld A,([$10],X) ld A,([$10.w],X) jrne loop jrne [$10] bset $10,#7 bset [$10],#7 btjt $10,#7,skip 00..FF 0000..FFFF 00..FF 00..1FE 0000..FFFF 00..FF 0000..FFFF 00..1FE 0000..FFFF PC-128/PC+1271) PC-128/PC+127 00..FF 00..FF 00..FF 00..FF byte 1) Syntax Destination/ Source Pointer Address (Hex.) Pointer Size (Hex.) +0 +1 +1 +2 Length (Bytes) + 0 (with X register) + 1 (with Y register) +1 +2 00..FF 00..FF 00..FF 00..FF 00..FF byte word byte word byte +2 +2 +2 +2 +1 +2 +1 +2 +2 Bit Indirect Relative btjt [$10],#7,skip 00..FF 00..FF byte +3 Note: 1. At the time the instruction is executed, the Program Counter (PC) points to the instruction following JRxx. 92/138 1 ST7L15, ST7L19 ST7 ADDRESSING MODES (cont'd) 12.1.1 Inherent All Inherent instructions consist of a single byte. The opcode fully specifies all the required information for the CPU to process the operation. Inherent Instruction NOP TRAP WFI HALT RET IRET SIM RIM SCF RCF RSP LD CLR PUSH/POP INC/DEC TNZ CPL, NEG MUL SLL, SRL, SRA, RLC, RRC SWAP Function No operation S/W Interrupt Wait For Interrupt (Low Power Mode) Halt Oscillator (Lowest Power Mode) Subroutine Return Interrupt Subroutine Return Set Interrupt Mask Reset Interrupt Mask Set Carry Flag Reset Carry Flag Reset Stack Pointer Load Clear Push/Pop to/from the stack Increment/Decrement Test Negative or Zero 1 or 2 Complement Byte Multiplication Shift and Rotate Operations Swap Nibbles 12.1.2 Immediate Immediate instructions have 2 bytes, the first byte contains the opcode, the second byte contains the operand value. Immediate Instruction LD CP BCP AND, OR, XOR ADC, ADD, SUB, SBC Load Compare Bit Compare Logical Operations Arithmetic Operations Function 12.1.3 Direct In Direct instructions, the operands are referenced by their memory address. The direct addressing mode consists of two submodes: Direct (Short) The address is a byte, thus requires only 1 byte after the opcode, but only allows 00 - FF addressing space. Direct (Long) The address is a word, thus allowing 64 Kbyte addressing space, but requires 2 bytes after the opcode. 12.1.4 Indexed (No Offset, Short, Long) In this mode, the operand is referenced by its memory address, which is defined by the unsigned addition of an index register (X or Y) with an offset. The indirect addressing mode consists of three submodes: Indexed (No Offset) There is no offset (no extra byte after the opcode), and allows 00 - FF addressing space. Indexed (Short) The offset is a byte, thus requires only 1 byte after the opcode and allows 00 - 1FE addressing space. Indexed (Long) The offset is a word, thus allowing 64 Kbyte addressing space and requires 2 bytes after the opcode. 12.1.5 Indirect (Short, Long) The required data byte to do the operation is found by its memory address, located in memory (pointer). The pointer address follows the opcode. The indirect addressing mode consists of two submodes: Indirect (Short) The pointer address is a byte, the pointer size is a byte, thus allowing 00 - FF addressing space, and requires 1 byte after the opcode. Indirect (Long) The pointer address is a byte, the pointer size is a word, thus allowing 64 Kbyte addressing space, and requires 1 byte after the opcode. 93/138 1 ST7L15, ST7L19 ST7 ADDRESSING MODES (cont'd) 12.1.6 Indirect Indexed (Short, Long) This is a combination of indirect and short indexed addressing modes. The operand is referenced by its memory address, which is defined by the unsigned addition of an index register value (X or Y) with a pointer value located in memory. The pointer address follows the opcode. The indirect indexed addressing mode consists of two submodes: Indirect Indexed (Short) The pointer address is a byte, the pointer size is a byte, thus allowing 00 - 1FE addressing space, and requires 1 byte after the opcode. Indirect Indexed (Long) The pointer address is a byte, the pointer size is a word, thus allowing 64 Kbyte addressing space, and requires 1 byte after the opcode. Table 20. Instructions Supporting Direct, Indexed, Indirect and Indirect Indexed Addressing Modes Long and Short Instructions LD CP AND, OR, XOR ADC, ADD, SUB, SBC BCP Load Compare Logical Operations Arithmetic Addition/subtraction operations Bit Compare Function 12.1.7 Relative Mode (Direct, Indirect) This addressing mode is used to modify the PC register value by adding an 8-bit signed offset to it. Available Relative Direct/ Indirect Instructions JRxx CALLR Function Conditional Jump Call Relative The relative addressing mode consists of two submodes: Relative (Direct) The offset follows the opcode. Relative (Indirect) The offset is defined in memory, of which the address follows the opcode. Short Instructions Only CLR INC, DEC TNZ CPL, NEG BSET, BRES BTJT, BTJF SLL, SRL, SRA, RLC, RRC SWAP CALL, JP Clear Function Increment/Decrement Test Negative or Zero 1 or 2 Complement Bit Operations Bit Test and Jump Operations Shift and Rotate Operations Swap Nibbles Call or Jump subroutine 94/138 1 ST7L15, ST7L19 12.2 INSTRUCTION GROUPS The ST7 family devices use an Instruction Set consisting of 63 instructions. The instructions may Load and Transfer Stack operation Increment/Decrement Compare and Tests Logical operations Bit Operation Conditional Bit Test and Branch Arithmetic operations Shift and Rotates Unconditional Jump or Call Conditional Branch Interruption management Condition Code Flag modification LD PUSH INC CP AND BSET BTJT ADC SLL JRA JRxx TRAP SIM WFI RIM HALT SCF IRET RCF CLR POP DEC TNZ OR BRES BTJF ADD SRL JRT SUB SRA JRF SBC RLC JP MUL RRC CALL SWAP CALLR SLA NOP RET BCP XOR CPL NEG RSP be subdivided into 13 main groups as illustrated in the following table: Using a prebyte The instructions are described with 1 to 4 bytes. In order to extend the number of available opcodes for an 8-bit CPU (256 opcodes), three different prebyte opcodes are defined. These prebytes modify the meaning of the instruction they precede. The whole instruction becomes: PC-2 End of previous instruction PC-1 Prebyte PC Opcode PC+1 Additional word (0 to 2) according to the number of bytes required to compute the effective address These prebytes enable instruction in Y as well as indirect addressing modes to be implemented. They precede the opcode of the instruction in X or the instruction using direct addressing mode. The prebytes are: PDY 90 Replace an X based instruction using immediate, direct, indexed, or inherent addressing mode by a Y one. PIX 92 Replace an instruction using direct, direct bit or direct relative addressing mode to an instruction using the corresponding indirect addressing mode. It also changes an instruction using X indexed addressing mode to an instruction using indirect X indexed addressing mode. PIY 91 Replace an instruction using X indirect indexed addressing mode by a Y one. 12.2.1 Illegal Opcode Reset In order to provide enhanced robustness to the device against unexpected behavior, a system of illegal opcode detection is implemented. If a code to be executed does not correspond to any opcode or prebyte value, a reset is generated. This, combined with the Watchdog, allows the detection and recovery from an unexpected fault or interference. Note: A valid prebyte associated with a valid opcode forming an unauthorized combination does not generate a reset. 95/138 1 ST7L15, ST7L19 INSTRUCTION GROUPS (cont'd) Mnemo ADC ADD AND BCP BRES BSET BTJF BTJT CALL CALLR CLR CP CPL DEC HALT IRET INC JP JRA JRT JRF JRIH JRIL JRH JRNH JRM JRNM JRMI JRPL JREQ JRNE JRC JRNC JRULT JRUGE JRUGT Description Add with Carry Addition Logical And Bit compare A, Memory Bit Reset Bit Set Jump if bit is false (0) Jump if bit is true (1) Call subroutine Call subroutine relative Clear Arithmetic Compare One Complement Decrement Halt Interrupt routine return Increment Absolute Jump Jump relative always Jump relative Never jump Jump if ext. interrupt = 1 Jump if ext. interrupt = 0 Jump if H = 1 Jump if H = 0 Jump if I = 1 Jump if I = 0 Jump if N = 1 (minus) Jump if N = 0 (plus) Jump if Z = 1 (equal) Jump if Z = 0 (not equal) Jump if C = 1 Jump if C = 0 Jump if C = 1 Jump if C = 0 Jump if (C + Z = 0) H=1? H=0? I=1? I=0? N=1? N=0? Z=1? Z=0? C=1? C=0? Unsigned < Jmp if unsigned >= Unsigned > jrf * Pop CC, A, X, PC inc X jp [TBL.w] reg, M H tst(Reg - M) A = FFH-A dec Y reg, M reg reg, M reg, M 0 I N N Z Z C M 0 N N N 1 Z Z Z C 1 Function/Example A=A+M+C A=A+M A=A.M tst (A . M) bres Byte, #3 bset Byte, #3 btjf Byte, #3, Jmp1 btjt Byte, #3, Jmp1 A A A A M M M M C C Dst M M M M Src H H H I N N N N N Z Z Z Z Z C C C 96/138 1 ST7L15, ST7L19 INSTRUCTION GROUPS (cont'd) Mnemo JRULE LD MUL NEG NOP OR POP Description Jump if (C + Z = 1) Load Multiply Negate (2's compl) No Operation OR operation Pop from the Stack A=A+M pop reg pop CC PUSH RCF RET RIM RLC RRC RSP SBC SCF SIM SLA SLL SRL SRA SUB SWAP TNZ TRAP WFI XOR Push onto the Stack Reset carry flag Subroutine Return Enable Interrupts Rotate left true C Rotate right true C Reset Stack Pointer Subtract with Carry Set carry flag Disable Interrupts Shift left Arithmetic Shift left Logic Shift right Logic Shift right Arithmetic Subtraction SWAP nibbles Test for Neg & Zero S/W trap Wait for Interrupt Exclusive OR A = A XOR M A M I=0 C <= Dst <= C C => Dst => C S = Max allowed A=A-M-C C=1 I=1 C <= Dst <= 0 C <= Dst <= 0 0 => Dst => C Dst7 => Dst => C A=A-M reg, M reg, M reg, M reg, M A M 1 N N 0 N N N N 1 0 N Z Z Z Z Z Z Z Z C C C C C A M N Z C 1 reg, M reg, M 0 N N Z Z C C push Y C=0 A reg CC M M M M reg, CC 0 H I N Z C N Z Function/Example Unsigned <= dst <= src X,A = X * A neg $10 reg, M A, X, Y reg, M M, reg X, Y, A 0 N Z N Z 0 C Dst Src H I N Z C Dst[7..4] <=> Dst[3..0] reg, M tnz lbl1 S/W interrupt 97/138 ST7L15, ST7L19 13 ELECTRICAL CHARACTERISTICS 13.1 PARAMETER CONDITIONS Unless otherwise specified, all voltages are referred to VSS. 13.1.1 Minimum and Maximum Values Unless otherwise specified, the minimum and maximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and frequencies by tests in production on 100% of the devices with an ambient temperature at TA = 25C and TA = TAmax (given by the selected temperature range). Data based on characterization results, design simulation and/or technology characteristics is indicated in the table footnotes and is not tested in production. Based on characterization, the minimum and maximum values refer to sample tests and represent the mean value plus or minus three times the standard deviation (mean3). 13.1.2 Typical Values Unless otherwise specified, typical data is based VDD = 5V (for the on TA = 25C, 4.5V VDD 5.5V voltage range) and VDD = 3.3V (for the 3V VDD 3.6V voltage range). They are given only as design guidelines and are not tested. 13.1.3 Typical Curves Unless otherwise specified, all typical curves are given only as design guidelines and are not tested. 13.1.4 Loading Capacitor The loading conditions used for pin parameter measurement are shown in Figure 58. Figure 58. Pin Loading Conditions 13.1.5 Pin Input Voltage The input voltage measurement on a pin of the device is described in Figure 59. Figure 59. Pin Input Voltage ST7 PIN VIN ST7 PIN CL 98/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.2 ABSOLUTE MAXIMUM RATINGS Stresses above those listed as "absolute maximum ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device under these condi13.2.1 Voltage Characteristics Symbol VDD - VSS VIN VESD(HBM) VESD(MM) Supply voltage Input voltage on any pin1) 2) Electrostatic discharge voltage (Human Body Model) Electrostatic discharge voltage (Machine Model) Ratings tions is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Maximum value 7.0 VSS - 0.3 to VDD + 0.3 Unit V See section 13.7.3 on page 112 13.2.2 Current Characteristics Symbol IVDD IVSS IIO Ratings Total current into VDD power lines (source)3) Total current out of VSS ground lines (sink)3) Output current sunk by any standard I/O and control pin Output current sunk by any high sink I/O pin Output current source by any I/Os and control pin Injected current on ISPSEL pin Injected current on RESET pin IINJ(PIN)2)4) Injected current on OSC1 and OSC2 pins Injected current on PB0 pin5) Injected current on any other pin6) IINJ(PIN) 2) Maximum value 75 150 20 40 - 25 5 5 5 +5 5 20 Unit mA Total injected current (sum of all I/O and control pins)6) 13.2.3 Thermal Characteristics Symbol TSTG TJ Ratings Storage temperature range Value -65 to +150 Unit C Maximum junction temperature (see Table 23, "Thermal Characteristics," on page 124) Notes: 1. Directly connecting the RESET and I/O pins to VDD or VSS could damage the device if an unintentional internal reset is generated or an unexpected change of the I/O configuration occurs (for example, due to a corrupted program counter). To guarantee safe operation, this connection must be made through a pull-up or pull-down resistor (typical: 4.7k for RESET, 10k for I/Os). Unused I/O pins must be tied in the same way to VDD or VSS according to their reset configuration. 2. IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS. 3. All power (VDD) and ground (VSS) lines must always be connected to the external supply. 4. Negative injection disturbs the analog performance of the device. In particular, it induces leakage currents throughout the device including the analog inputs. To avoid undesirable effects on the analog functions, care must be taken: - Analog input pins must have a negative injection less than 0.8 mA (assuming that the impedance of the analog voltage is lower than the specified limits) - Pure digital pins must have a negative injection less than 1.6mA. In addition, it is recommended to inject the current as far as possible from the analog input pins. 5. No negative current injection allowed on PB0 pin. 6. When several inputs are submitted to a current injection, the maximum IINJ(PIN) is the absolute sum of the positive and negative injected currents (instantaneous values). These results are based on characterization with IINJ(PIN) maximum current injection on four I/O port pins of the device. 99/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.3 OPERATING CONDITIONS 13.3.1 General Operating Conditions TA = -40 to +125C, unless otherwise specified. Symbol VDD fCLKIN TA Supply voltage External clock frequency on CLKIN pin Ambient temperature range Parameter Conditions fOSC = 16 MHz max TA = -40C to TA max VDD 3V A Suffix version C Suffix version Min 3.0 0 -40 -40 Max 5.5 16 +85 +125 Unit V MHz C Figure 60. fCLKIN Maximum Operating Frequency vs VDD Supply Voltage fCLKIN [MHz] FUNCTIONALITY GUARANTEED IN THIS AREA (UNLESS OTHERWISE STATED IN THE TABLES OF PARAMETRIC DATA). REFER TO section 13.3.3 on page 105 FOR PLL OPERATING RANGE 16 FUNCTIONALITY NOT GUARANTEED IN THIS AREA 8 4 1 0 2.0 2.7 3.0 3.3 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE [V] Note: For further information on clock management block diagram for fCLKIN description, refer to Figure 12 in section 7 on page 21. 100/138 ST7L15, ST7L19 OPERATING CONDITIONS (cont'd) The RC oscillator and PLL characteristics are temperature-dependent. 13.3.1.1 Operating Conditions (tested for TA = -40 to +125C) @ VDD = 4.5 to 5.5V Symbol Conditions RCCR = FF (reset value), TA = 25C, VDD = 5V fRC1) Internal RC oscillator frequency RCCR = RCCR02 ), TA = 25C, VDD = 5V TA = 25C, VDD = 5V Accuracy of Internal RC oscillator TA = 25C, VDD = 4.5 to 5.5V4) ACCRC with RCCR = RCCR02)3) TA = -40 to +125C, VDD = 4.5 to 5.5V4) IDD(RC) RC oscillator current consumption TA = 25C, VDD = 5V RC oscillator setup time tsu(RC) x8 PLL input clock fPLL PLL Lock time8) tLOCK tSTAB PLL Stabilization time8) fRC = 1 MHz @ TA = 25C, VDD = 4.5 to 5.5V4) ACCPLL x8 PLL Accuracy fRC = 1 MHz @ TA = -40 to +125C, VDD = 5V JITPLL PLL jitter (fCPU/fCPU) IDD(PLL) PLL current consumption TA = 25C Parameter Min 992 -0.8 -1 -3.5 Typ 700 1000 Max Unit 1008 +0.8 +1 +7 102) 1 2 4 0.17) 0.17) 16) 6004) kHz % A s MHz ms 6004)5) % A Notes: 1. If the RC oscillator clock is selected, to improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device. 2. See "INTERNAL RC OSCILLATOR ADJUSTMENT" on page 21. 3. Minimum value is obtained for hot temperature and max value is obtained for cold temperature. 4. Data based on characterization results, not tested in production 5. Measurement made with RC calibrated at 1 MHz. 6. Guaranteed by design. 7. Averaged over a 4ms period. After the LOCKED bit is set, a period of tSTAB is required to reach ACCPLL accuracy. 8. After the LOCKED bit is set ACCPLL is maximum 10% until tSTAB has elapsed. See Figure 11 on page 22. Figure 61. Typical Accuracy with RCCR = RCCR0 vs VDD = 4.5 to 5.5V and Temperature 3.50% 3.00% 2.50% 2.00% Accuracy (%) -45 -10 0 25 90 110 130 1.50% 1.00% 0.50% 0.00% -0.50% -1.00% 4.5 4.6 4.7 4.8 4.9 5 Vdd (V) 5.1 5.2 5.3 5.4 5.5 101/138 ST7L15, ST7L19 OPERATING CONDITIONS (cont'd) Figure 62. fRC vs VDD and Temperature for Calibrated RCCR0 1.025 1.02 1.015 1.01 -45 -10 0 25 90 110 130 Frequency (MHz) 1.005 1 0.995 0.99 0.985 0.98 4.5 4.6 4.7 4.8 4.9 5 Vdd (V) 5.1 5.2 5.3 5.4 5.5 13.3.1.2 Operating Conditions (tested for TA = -40 to +125C) @ VDD = 3.0 to 3.6V1) Symbol fRC2) Parameter1) Conditions Min 992 -0.8 -1 -5 4005) 103) 0.7 2 4 fRC = 1 MHz @ TA = -40 to +125C, VDD = 3.3V fRC = 1 MHz @ TA = 25C, VDD = 3 to 3.6V 0.17) 0.17) 16) 190 A % Typ 700 1000 1008 +0.8 +1 +6.5 A s MHz ms % Max Unit kHz Internal RC oscillator fre- RCCR = FF (reset value), TA = 25C, VDD = 3.3V quency RCCR = RCCR13), TA = 25C, VDD = 3.3V Accuracy of Internal RC TA = 25C, VDD = 3.3V oscillator when calibrated TA = 25C, VDD = 3 to 3.6V with RCCR = RCCR13)4) T = -40 to +125C, V = 3 to 3.6V A DD RC oscillator current conTA = 25C, VDD = 3.3V sumption RC oscillator setup time x4 PLL input clock PLL lock time8) PLL stabilization time8) x4 PLL accuracy PLL jitter (fCPU/fCPU) PLL current consumption TA = 25C TA = 25C, VDD = 3.3V ACCRC IDD(RC) tsu(RC) fPLL tLOCK tSTAB ACCPLL JITPLL IDD(PLL) Notes: 1. Data based on characterization results, not tested in production. 2. If the RC oscillator clock is selected, to improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device. 3. See "INTERNAL RC OSCILLATOR ADJUSTMENT" on page 21. 4. Minimum value is obtained for hot temperature and maximum value is obtained for cold temperature. 5. Measurement made with RC calibrated at 1 MHz. 6. Guaranteed by design. 7. Averaged over a 4ms period. After the LOCKED bit is set, a period of tSTAB is required to reach ACCPLL accuracy. 8. After the LOCKED bit is set, ACCPLL is maximum 10% until tSTAB has elapsed. See Figure 11 on page 22. 102/138 ST7L15, ST7L19 OPERATING CONDITIONS (cont'd) Figure 63. Typical Accuracy with RCCR = RCCR1 vs VDD = 3 to 3.6V and Temperature 1.50% 1.00% -45 Accuracy (%) 0.50% -10 0 25 90 0.00% 110 130 -0.50% -1.00% 3 3.1 3.2 3.3 Vdd (V) 3.4 3.5 3.6 Figure 64. fRC vs VDD and Temperature for Calibrated RCCR1 1.01 1.005 1 Frequency (MHz) -45 -10 0.995 0 25 90 110 0.99 130 0.985 0.98 3 3.1 3.2 3.3 Vdd (V) 3.4 3.5 3.6 103/138 ST7L15, ST7L19 OPERATING CONDITIONS (cont'd) Figure 65. PLLx4 Output vs CLKIN Frequency 7.00 11.00 Output Frequency (MHz) Output Frequency (MHz) 6.00 5.00 4.00 3.00 2.00 1.00 1 1.5 2 2.5 3 3.3 3 2.7 9.00 7.00 5.00 3.00 1.00 0.85 0.9 1 1.5 2 2.5 5.5 5 4.5 4 Figure 66. PLLx8 Output vs CLKIN Frequency External Input Clock Frequency (MHz) External Input Clock Frequency (MHz) Note: fOSC = fCLKIN/2*PLL4 Note: fOSC = fCLKIN/2*PLL8 104/138 ST7L15, ST7L19 OPERATING CONDITONS (cont'd) 13.3.2 Operating Conditions with Low Voltage Detector (LVD) TA = -40 to +125C, unless otherwise specified. Symbol VIT+(LVD) VIT-(LVD) Vhys VtPOR tg(VDD) IDD(LVD) Parameter Reset release threshold (VDD rise) Reset generation threshold (VDD fall) LVD voltage threshold hysteresis VDD rise time rate 3)5) Not detected by the LVD 200 Filtered glitch delay on VDD LVD current consumption VIT+(LVD)-VIT-(LVD) 0.022) Conditions1) Min 3.80 2) Typ 4.20 4.00 200 Max 4.60 4.352) 1002) 1504) Unit V mV ms/V ns A 3.70 Notes: 1. LVD functionality guaranteed only within the VDD operating range specified in section 13.3.1 on page 100. 2. Not tested in production. 3. Not tested in production. The VDD rise time rate condition is needed to insure a correct device power-on and LVD reset. When the VDD slope is outside these values, the LVD may not ensure a proper reset of the MCU. 4. Based on design simulation. 5. Use of LVD with capacitive power supply: With this type of power supply, if power cuts occur in the application, it is recommended to pull VDD down to 0V to ensure optimum restart conditions. Refer to circuit example in Figure 95 on page 119 and note 4. 13.3.3 Internal RC Oscillator and PLL The ST7 internal clock can be supplied by an internal RC oscillator and PLL (selectable by option byte). Symbol VDD(RC) VDD(x4PLL) VDD(x8PLL) Parameter Internal RC oscillator operating voltage x4 PLL operating voltage1) x8 PLL operating voltage Conditions Refer to operating range of VDD with TA, section 13.3.1 on page 100 Min 3.0 3.0 3.6 Typ Max 5.5 3.6 5.5 PLL input clock (fPLL) cycles V Unit tSTARTUP PLL Start-up time 60 Notes: 1. x4 PLL option only applicable on Flash devices. 105/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.4 SUPPLY CURRENT CHARACTERISTICS The following current consumption specified for the ST7 functional operating modes over temperature range does not take into account the clock source current consumption. To obtain the total device consumption, the two current values must be added (except for HALT mode for which the clock is stopped). 13.4.1 Supply Current TA = -40 to +125C, unless otherwise specified. Symbol Parameter Supply current in RUN mode Supply current in WAIT mode Supply current in SLOW mode Supply current in SLOW WAIT mode Supply current in HALT mode5) Supply current in AWUFH mode6)7) Supply current in ACTIVE HALT mode Conditions fCPU = 8 MHz1) fCPU = 8 MHz2) fCPU = 250 kHz3) VDD = 5.5V fCPU = 250 kHz4) -40C TA +125C -40C TA +125C -40C TA +125C Typ 7 3 0.7 0.5 1 60 TBD Max 9 3.6 0.9 0.8 6 TBD Unit mA IDD A mA Notes: 1. CPU running with memory access, all I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (CLKIN) driven by external square wave, LVD disabled. 2. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (CLKIN) driven by external square wave, LVD disabled. 3. SLOW mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (CLKIN) driven by external square wave, LVD disabled. 4. SLOW-WAIT mode selected with fCPU based on fOSC divided by 32. All I/O pins in input mode with a static value at VDD or VSS (no load), all peripherals in reset state; clock input (CLKIN) driven by external square wave, LVD disabled. 5. All I/O pins in output mode with a static value at VSS (no load), LVD disabled. Data based on characterization results, tested in production at VDD max and fCPU max. 6. All I/O pins in input mode with a static value at VDD or VSS (no load). Data tested in production at VDD max. and fCPU max. 7. This consumption refers to the Halt period only and not the associated run period which is software dependent. Figure 67. Typical IDD in RUN vs fCPU 9 .5 8 7 IDD run (mA) vs Freq (MHz) 1 2 4 6 5 6 8 Figure 68. Typical IDD in RUN at fCPU = 8 MHz 9 8 7 IDD run (mA) at fCPU=8MHz 6 140C 5 90C 4 25C 3 -5C 2 -45C 1 0 4 3 2 1 0 2 2.5 3 3.5 4 Vdd (V) 4.5 5 5.5 6 6.5 2 2.5 3 4 4.5 5 5.5 6 6.5 Note: Graph displays data 3.5 beyond the normal operating range of 3V - 5.5V Vdd (V) Note: Graph displays data beyond the normal operating range of 3V - 5.5V Note: Graph displays data beyond the normal operating range of 3V - 5.5V 106/138 ST7L15, ST7L19 SUPPLY CURRENT CHARACTERISTICS (cont'd) Figure 69. Typical IDD in SLOW vs fCPU 0.90 0.80 0.70 0.60 0.50 0.40 0.30 0.20 0.10 0.00 250KHz 125KHz 62KHz Figure 72. Typical IDD in SLOW-WAIT vs fCPU 0.60 250KHz 0.50 IDD (mA) 0.40 0.30 0.20 0.10 125KHz IDD (mA) TB D 2.7 3.3 4 5 6 0.00 2.7 3.3 4 5 6 VDD (V) Note: Graph displays data beyond the normal operating range of 3V - 5.5V VDD (V) Note: Graph displays data beyond the normal operating range of 3V - 5.5V Figure 70. Typical IDD in WAIT vs fCPU 4 3.5 0.5 1 3 IDD wfi (mA) vs Fcpu (MHz) 2 4 2.5 Figure 73. Typical IDD vs Temperature at VDD = 5V and fCPU = 8 MHz 6.00 5.00 RUN 4.00 Idd (mA) 3.00 2.00 1.00 0.00 -45 WAIT SLOW SLOW-WAIT 6 2 8 1.5 1 0.5 TB D 25 TB D 90 110 Temperature (C) 62KHz 0 2 2.5 3 3.5 4 Vdd (V) 4.5 5 5.5 6 6.5 Note: Graph displays data beyond the normal operating range of 3V - 5.5V Figure 71. Typical IDD in WAIT at fCPU = 8 MHz 4 3.5 0.5 1 3 IDD wfi (mA) vs Fcpu (MHz) 2 4 2.5 6 2 8 1.5 1 0.5 0 2 2.5 3 3.5 4 Vdd (V) 4.5 5 5.5 6 6.5 Note: Graph displays data beyond the normal operating range of 3V - 5.5V 107/138 ST7L15, ST7L19 SUPPLY CURRENT CHARACTERISTICS (cont'd) 13.4.2 On-chip Peripherals Symbol IDD(AT) IDD(SPI) IDD(ADC) Parameter 12-bit Auto-Reload Timer supply current1) SPI supply current2) ADC supply current when converting3) Conditions fCPU = 4 MHz VDD = 3.3V VDD = 5V fCPU = 8 MHz fCPU = 4 MHz VDD = 3.3V VDD = 5V fCPU = 8 MHz VDD = 3.3V fADC = 4 MHz VDD = 5V Typ 150 1000 50 200 250 1100 Unit A Notes: 1. Data based on a differential IDD measurement between reset configuration (timer stopped) and a timer running in PWM mode at fCPU = 8 MHz. 2. Data based on a differential IDD measurement between reset configuration and a permanent SPI master communication (data sent equal to 55h). 3. Data based on a differential IDD measurement between reset configuration and continuous A/D conversions. 13.5 CLOCK AND TIMING CHARACTERISTICS Subject to general operating conditions for VDD, fOSC and TA. 13.5.1 General Timings Symbol tc(INST) tv(IT) Parameter1) Instruction cycle time Interrupt reaction time3) tv(IT) = tc(INST) + 10 fCPU = 8 MHz Conditions Min 2 250 10 1.25 Typ2) 3 375 Max 12 1500 22 2.75 Unit tCPU ns tCPU s Notes: 1. Guaranteed by Design. Not tested in production. 2. Data based on typical application software. 3. Time measured between interrupt event and interrupt vector fetch. Dtc(INST) is the number of tCPU cycles needed to finish the current instruction execution. 13.5.2 Auto Wake-Up from Halt Oscillator (AWU)1) Symbol fAWU tRCSRT Parameter AWU oscillator frequency AWU oscillator start-up time Conditions Min 50 Typ 125 Max 250 50 Unit kHz s Notes: 1. Guaranteed by Design. Not tested in production. 108/138 ST7L15, ST7L19 CLOCK AND TIMING CHARACTERISTICS (cont'd) 13.5.3 Crystal and Ceramic Resonator Oscillators The ST7 internal clock can be supplied with ten different Crystal/Ceramic resonator oscillators. All the information given in this paragraph are based on characterization results with specified typical external components. In the application, the resonator and the load capacitors must be placed as Symbol fCrOSC CL1 CL2 Parameter Crystal oscillator frequency1) Recommended load capacitance versus equivalent serial resistance of the crystal or ceramic resonator (RS) fCrOSC (MHz) 1 2 4 Murata 8 12 16 Typical Ceramic Resonators2) Type3) Reference SMD CSBFB1M00J58-R0 LEAD CSBLA1M00J58-B0 SMD CSTCC2M00G56Z-R0 SMD CSTCR4M00G53Z-R0 LEAD CSTLS4M00G53Z-B0 SMD CSTCE8M00G52Z-R0 LEAD CSTLS8M00G53Z-B0 SMD CSTCE12M0G52Z-R0 SMD CSTCE16M0V51Z-R0 LEAD CSTLS16M0X51Z-B0 CL14) (pF) 220 (47) (15) (10) (15) (10) (5) CL24) (pF) 220 (47) (15) (10) (15) (10) (5) close as possible to the oscillator pins in order to minimize output distortion and start-up stabilization time. Refer to the crystal/ceramic resonator manufacturer for more details (frequency, package, accuracy...). Min 2 See table below Typ Max 16 Unit MHz pF Conditions Supplier Rd Supply Voltage Temperature () Range (V) Range (C) 2.2k 0 0 0 0 0 0 3.6V to 5.5V 3.0V to 5.5V 3.6V to 5.5V -40 to +125 Notes: 1. When PLL is used, please refer to the PLL characteristics chapter and to "SUPPLY, RESET AND CLOCK MANAGEMENT" on page 21 chapter (fCrOSC min. is 8 MHz with PLL). 2. Resonator characteristics given by the ceramic resonator manufacturer. For more information on these resonators, please consult www.murata.com 3. SMD = [-R0: Plastic tape package ( =180mm)] LEAD = [-B0: Bulk] 4. () means load capacitor built in resonator Figure 74. Typical Application with a Crystal or Ceramic Resonator WHEN RESONATOR WITH INTEGRATED CAPACITORS CL1 OSC1 i2 fOSC RESONATOR CL2 Rd OSC2 ST7 109/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.6 MEMORY CHARACTERISTICS 13.6.1 RAM and Hardware Registers TA = -40 to +125C, unless otherwise specified. Symbol VRM Parameter Data retention mode 1) Conditions HALT mode (or RESET) Min 1.6 Typ Max Unit V 13.6.2 Flash Program Memory TA = -40 to +85C, unless otherwise specified Symbol VDD tprog tRET4) NRW Parameter Operating voltage for Flash write/erase Programming time for 1~32 bytes2) Programming time for 1.5 Kbytes Data retention Write erase cycles Conditions Refer to operating range of VDD with TA, section 13.3.1 on page 100 TA = -40 to +85C TA = 25C TA = 55C3) TPROG = 25C TPROG = 85C Read / Write / Erase modes fCPU = 8 MHz, VDD = 5.5V No Read/No Write Mode Power down mode / HALT Min 3.0 5 0.24 20 1K 300 2.65) 100 0.1 Typ Max 5.5 10 0.48 Unit V ms s years cycles mA A IDD Supply current 0 13.6.3 EEPROM Data Memory TA = -40 to +125C, unless otherwise specified Symbol VDD tprog Parameter Operating voltage for EEPROM write/ erase Programming time for 1~32 bytes Data retention with 1k cycling (TPROG = -40 to +125C tRET4) Data retention with 10k cycling (TPROG = -40 to +125C) Data retention with 100k cycling (TPROG = -40 to +125C) TA = 55C3) Conditions Refer to operating range of VDD with TA, section 13.3.1 on page 100 TA = -40 to +125C Min 3.0 5 20 10 1 years Typ Max 5.5 10 Unit V ms Notes: 1. Minimum VDD supply voltage without losing data stored in RAM (in HALT mode or under RESET) or in hardware registers (only in HALT mode). Guaranteed by construction, not tested in production. 2. Up to 32 bytes can be programmed at a time. 3. The data retention time increases when the TA decreases. 4. Data based on reliability test results and monitored in production. 5. Guaranteed by Design. Not tested in production. 110/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.7 EMC CHARACTERISTICS Susceptibility tests are performed on a sample basis during product characterization. 13.7.1 Functional EMS (Electro Magnetic Susceptibility) Based on a simple running application on the product (toggling two LEDs through I/O ports), the product is stressed by two electro magnetic events until a failure occurs (indicated by the LEDs). ESD: Electro-Static Discharge (positive and negative) is applied on all pins of the device until a functional disturbance occurs. This test conforms with the IEC 1000-4-2 standard. FTB: A Burst of Fast Transient voltage (positive and negative) is applied to VDD and VSS through a 100pF capacitor, until a functional disturbance occurs. This test conforms with the IEC 1000-44 standard. A device reset allows normal operations to resume. The test results are given in the table below based on the EMS levels and classes defined in application note AN1709. 13.7.1.1 Designing Hardened Software to Avoid Noise Problems EMC characterization and optimization are performed at component level with a typical applicaSymbol VFESD VFFTB Parameter Voltage limits to be applied on any I/O pin to induce a functional disturbance Fast transient voltage burst limits to be applied through 100pF on VDD and VDD pins to induce a functional disturbance tion environment and simplified MCU software. It should be noted that good EMC performance is highly dependent on the user application and the software in particular. Therefore, it is recommended that EMC software optimization and prequalification tests are made relative to the EMC level requested for the user's application. Software recommendations: The software flowchart must include the management of runaway conditions such as: - Corrupted program counter - Unexpected reset - Critical data corruption (control registers...) Prequalification trials: Most of the common failures (unexpected reset and program counter corruption) can be reproduced by manually forcing a low state on the RESET pin or the Oscillator pins for 1 second. To complete these trials, ESD stress can be applied directly on the device, over the range of specification values. When unexpected behavior is detected, the software can be hardened to prevent unrecoverable errors occurring (see application note AN1015). Conditions VDD = 5V, TA = 25C, fOSC = 8 MHz, conforms to IEC 1000-4-2 VDD = 5V, TA = 25C, fOSC = 8 MHz, conforms to IEC 1000-4-4 Level/ Class 2B 3B 13.7.2 Electro Magnetic Interference (EMI) Based on a simple application running on the product (toggling two LEDs through the I/O ports), the product is monitored in terms of emission. This emission test is in line with the norm SAE J 1752/ 3 which specifies the board and the loading of each pin. Symbol Parameter Max vs [fOSC/fCPU] 8/4 MHz 16/8 MHz 0.1 MHz to 30 MHz 15 20 VDD = 5V, TA = 25C, 30 MHz to 130 MHz 17 21 SO20 package, 130 MHz to 1 GHz 12 15 conforming to SAE J 1752/3 SAE EMI Level 3 Conditions Monitored Frequency Band Unit SEMI Peak level1) dBV - Notes: 1. Data based on characterization results, not tested in production. 111/138 ST7L15, ST7L19 EMC CHARACTERISTICS (cont'd) 13.7.3 Absolute Maximum Ratings (Electrical Sensitivity) Based on two different tests (ESD and LU) using specific measurement methods, the product is stressed in order to determine its performance in terms of electrical sensitivity. For more details, refer to application note AN1181. 13.7.3.1 Electro-Static Discharge (ESD) Electro-Static Discharges (a positive then a negative pulse separated by 1 second) are applied to the pins of each sample according to each pin combination. The sample size depends on the number of supply pins in the device (3 parts*(n+1) supply pin). Two models can be simulated: Human Body Model and Machine Model. This test conforms to the JESD22-A114A/A115A standard. Maximum value1) 8000 TA = 25C 400 1000 V Absolute Maximum Ratings Symbol VESD(HBM) VESD(MM) VESD(CDM) Ratings Electro-static discharge voltage (Human Body Model) Electro-static discharge voltage (Machine Model) Electro-static discharge voltage (Charge Device Model) Conditions Unit Notes: 1. Data based on characterization results, not tested in production. 13.7.3.2 Static and Dynamic Latch-Up (LU) Three complementary static tests are required on six parts to assess the latch-up performance. A supply overvoltage (applied to each power supply pin) and a current injection (applied to each input, Electrical Sensitivities Symbol LU DLU Parameter Static latch-up class Dynamic latch-up class TA = 25C TA = 125C output and configurable I/O pin) are performed on each sample. This test conforms to the EIA/JESD 78 IC latch-up standard. For more details, refer to application note AN1181. Conditions Class1) A A VDD = 5.5V, fOSC = 4 MHz, TA = 25C Notes: 1. Class description: A Class is an STMicroelectronics internal specification. All its limits are higher than the JEDEC specifications, which means when a device belongs to Class A it exceeds the JEDEC standard. Class B strictly covers all the JEDEC criteria (international standard). 112/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.8 I/O PORT PIN CHARACTERISTICS 13.8.1 General Characteristics Subject to general operating conditions for VDD, fOSC, and TA, unless otherwise specified. Symbol VIL VIH Vhys IL IS RPU CIO tf(IO)out tr(IO)out tw(IT)in Parameter Input low level voltage Input high level voltage Schmitt trigger voltage hysteresis1) Input leakage current Static current consumption induced by each floating input pin2) Weak pull-up equivalent resistor3) I/O pin capacitance Output high to low level fall time1) Output low to high level rise time1) External interrupt pulse time4) CL = 50pF Between 10% and 90% 1 VSS VIN VDD Floating input mode VIN = VSS VDD = 5V VDD = 3V 50 400 120 160 5 25 25 250 Conditions Min VSS - 0.3 0.7xVDD 400 1 A Typ Max 0.3xVDD VDD + 0.3 Unit V mV k pF ns tCPU Notes: 1. Data based on validation/design results. 2. Configuration not recommended, all unused pins must be kept at a fixed voltage: Using the output mode of the I/O for example or an external pull-up or pull-down resistor (see Figure 75). Static peak current value taken at a fixed VIN value, based on design simulation and technology characteristics, not tested in production. This value depends on VDD and temperature values. 3. The RPU pull-up equivalent resistor is based on a resistive transistor (corresponding IPU current characteristics described in Figure 76 on page 115). 4. To generate an external interrupt, a minimum pulse width must be applied on an I/O port pin configured as an external interrupt source. Figure 75. Two Typical Applications with Unused I/O Pin VDD 10k ST7 10k UNUSED I/O PORT UNUSED I/O PORT ST7 Caution: During normal operation the ICCCLK pin must be pulled up, internally or externally (external pull-up of 10k mandatory in noisy environment). This is to avoid entering ICC mode unexpectedly during a reset. Note: I/O can be left unconnected if it is configured as output (0 or 1) by the software. This has the advantage of greater EMC robustness and lower cost. 113/138 ST7L15, ST7L19 I/O PORT PIN CHARACTERISTICS (cont'd) 13.8.2 Output Driving Current Subject to general operating conditions for VDD, fCPU and TA (-40 to +125C), unless otherwise specified. Symbol Parameter Output low level voltage for a standard I/O pin when eight pins are sunk at same time (see Figure 77) Output low level voltage for a high sink I/O pin when four pins are sunk at same time (see Figure 80) Output high level voltage for an I/O pin when four pins are sourced at same time (see Figure 86) Output low level voltage for a standard I/O pin when eight pins are sunk at same time (see Figure 76) VDD = 5V Conditions IIO = +5mA IIO = +2mA IIO = +20mA IIO = +8mA IIO = -5mA IIO = -2mA IIO = +2mA, TA +85C VDD - 1.5 VDD - 0.8 V Min Typ Max 1.0 0.4 1.3 0.75 Unit VOL1) VOH2) VOL1)3) 0.5 VOH2)3) Output low level voltage for a high sink I/O I = +8mA, VDD = 3.3V IO pin when four pins are sunk at same time TA +85C Output high level voltage for an I/O pin IIO = -2mA, when four pins are sourced at same time TA +85C (Figure 85) VDD - 0.8 Notes: 1. The IIO current sunk must always respect the absolute maximum rating specified in section 13.2.2 on page 99 and the sum of IIO (I/O ports and control pins) must not exceed IVSS. 2. The IIO current sourced must always respect the absolute maximum rating specified in section 13.2.2 on page 99 and the sum of IIO (I/O ports and control pins) must not exceed IVDD. 3. Not tested in production, based on characterization results. 114/138 ST7L15, ST7L19 I/O PORT PIN CHARACTERISTICS (cont'd) Figure 76. Typical VOL at VDD = 3.3V (Standard) 0.6 140C 90C 0.5 90C 25C 0.4 -5C 0.3 -45C 1 25C Vol std i/o (V) at VDD=3.3V Vol Port C (V) at VDD=5V 0.8 -5C -45C Figure 79. Typical VOL at VDD = 5V (Port C) 1.2 140C 0.6 0.2 0.4 0.1 0.2 0 0 0.5 1 1.5 Iol (mA) 2 2.5 3 3.5 0 0 1 2 3 4 Iol (mA) 5 6 7 8 Figure 77. Typical VOL at VDD = 5V (Standard) 140C 1.2 90C 1 25C -5C -45C 0.6 Figure 80. Typical VOL at VDD = 3.3V (High-sink) 0.6 140C 90C 25C 0.5 Vol High sink (V) at VDD=3.3V Vol std i/o (V) at VDD=5V 0.8 0.4 -5C -45C 0.3 0.4 0.2 0.2 0.1 0 0 1 2 3 4 Iol (mA) 5 6 7 8 0 0 2 4 6 Iol (mA) 8 10 12 Figure 78. Typical VOL at VDD = 3.3V (Port C) 0.7 140C 90C 0.6 25C Vol Port C (V) at VDD=3.3V 0.5 -5C 0.4 -45C 0.3 Figure 81. Typical VOL at VDD = 5V (High-sink) 1.6 1.4 140C 90C 25C -5C -45C 0.8 0.6 Vol High sink (V) at VDD=5V 1.2 1 0.2 0.4 0.1 0.2 0 0 0.5 1 1.5 Iol (mA) 2 2.5 3 3.5 0 5 10 15 Iol (mA) 20 25 30 35 0 115/138 ST7L15, ST7L19 I/O PORT PIN CHARACTERISTICS (cont'd) Figure 82. Typical VOL vs VDD (Standard I/Os) 0.6 140C 90C 25C Vol std i/o (V) at Iio=2mA 0.4 -5C -45C 0.3 |vdd-voh| std i/o (V) at VDD=3.3V Figure 85. Typical VDD - VOH at VDD = 3.3V 0.9 140C 0.8 90C 0.7 25C 0.6 -5C 0.5 -45C 0.4 0.3 0.2 0.5 0.2 0.1 0.1 0 0 2 2.5 3 3.5 4 VDD (V) 4.5 5 5.5 6 6.5 0 0.5 1 1.5 Iol (mA) 2 2.5 3 3.5 Figure 83. Typical VOL vs VDD (High-sink) 140C 0.7 90C 0.6 25C -5C -45C Figure 86. Typical VDD - VOH at VDD = 5V 1.6 140C 1.4 90C |vdd-voh| std i/o (V) at VDD=5V 1.2 25C 1 -5C -45C Vol High sink (V) at Iio=8mA 0.5 0.4 0.8 0.6 0.4 0.3 0.2 0.2 0.1 0 0 1 2 3 4 Iol (mA) 5 6 7 8 0 2 2.5 3 3.5 4 Vdd (V) 4.5 5 5.5 6 6.5 Figure 84. Typical VOL vs VDD (Port C) 140C 0.6 90C 25C -5C -45C 0.3 Figure 87. Typical VDD - VOH at VDD = 3.3V (HS) 0.9 0.8 |vdd-voh| high sink i/o (V) at VDD=3.3V 0.7 25C 0.6 -5C 0.5 -45C 0.4 0.3 0.2 0.1 0 140C 90C 0.5 Vol Port C (V) at lio=2mA 0.4 0.2 0.1 0 2 2.5 3 3.5 4 Vdd (V) 4.5 5 5.5 6 6.5 0 0.5 1 1.5 Iol (mA) 2 2.5 3 3.5 116/138 ST7L15, ST7L19 I/O PORT PIN CHARACTERISTICS (cont'd) Figure 88. Typical VDD - VOH at VDD = 5V (HS) 1.6 140C 0.8 1.4 90C |vdd-voh| high sink i/o (V) at VDD=5V 0.7 1.2 1 25C -5C -45C |vdd-voh| std i/o (V) at loh=2mA 0.6 -5C 0.5 -45C 0.4 0.3 0.2 0.1 0 0 1 2 3 4 Iol (mA) 5 6 7 8 2 2.5 3 3.5 4 vdd (V) 4.5 5 5.5 6 6.5 25C 90C Figure 91. Typical VDD - VOH vs VDD (Standard) 0.9 140C 0.8 0.6 0.4 0.2 0 Figure 89. Typical VDD - VOH at VDD = 3.3V (Port C) 1.2 140C Figure 92. Typical VDD-VOH vs VDD (High Sink) 0.9 0.8 0.7 25C 0.6 -5C 0.5 -45C 0.4 0.3 0.2 0.1 0 140C 90C |vdd-voh| high sink i/o (V) at loh=2mA vs VDD 1 |vdd-voh| Port C (V) at VDD=3.3V 90C 25C 0.8 -5C 0.6 -45C 0.4 0.2 0 0 0.5 1 1.5 2 Iol (mA) 2.5 3 3.5 4 4.5 2 2.5 3 3.5 4 vdd (V) 4.5 5 5.5 6 6.5 Figure 90. Typical VDD-VOH at VDD = 5V (Port C) 1.4 140C 90C Figure 93. Typical VDD-VOH vs VDD (Port C) 140C 0.9 90C 0.8 |vdd-voh| Port C (V) at Iio=2mA vs VDD 25C 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 -5C -45C 1.2 |vdd-voh| Port C (V) at VDD=5V 25C 1 -5C 0.8 -45C 0.6 0.4 0.2 0 0 1 2 3 4 Iol (mA) 5 6 7 8 2 2.5 3 3.5 4 vdd (V) 4.5 5 5.5 6 6.5 117/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.9 CONTROL PIN CHARACTERISTICS 13.9.1 Asynchronous RESET Pin TA = -40 to +125C, unless otherwise specified. Symbol VIL 1) Parameter Input low-level voltage Input high-level voltage Schmitt trigger voltage hysteresis1) Output low-level voltage2) Conditions Min Vss - 0.3 0.7xVDD Typ Max 0.3xVDD VDD + 0.3 Unit VIH1) Vhys VOL1) 2 IIO = +5mA, TA +125C IIO = +2mA, TA +125C 20 40 0.5 0.2 40 70 30 20 200 ns 1.0 0.4 80 120 k V VDD = 5V VDD = 5V RON tw(RSTL)ou t Pull-up equivalent resistor1)3) Generated reset pulse duration External reset pulse hold time Filtered glitch duration 4) VDD = 3.3V1) Internal reset sources s th(RSTL)in tg(RSTL)in Notes: 1. Data based on characterization results, not tested in production. 2. The IIO current sunk must always respect the absolute maximum rating specified in section 13.2.2 on page 99 and the sum of IIO (I/O ports and control pins) must not exceed IVSS. 3. The RON pull-up equivalent resistor is based on a resistive transistor. Specified for voltages on RESET pin between VILmax and VDD. 4. To guarantee the reset of the device, a minimum pulse must be applied to the RESET pin. All short pulses applied on RESET pin with a duration below th(RSTL)in can be ignored. 118/138 ST7L15, ST7L19 CONTROL PIN CHARACTERISTICS (cont'd) Figure 94. RESET Pin Protection When LVD Is Enabled1)2)3)4) VDD ST7 Required EXTERNAL RESET 0.01F Optional (note 3) RON Filter INTERNAL RESET 1M PULSE GENERATOR WATCHDOG ILLEGAL OPCODE5) LVD RESET Figure 95. RESET Pin Protection When LVD Is Disabled1) VDD ST7 USER EXTERNAL RESET CIRCUIT 0.01F RON Filter INTERNAL RESET PULSE GENERATOR WATCHDOG ILLEGAL OPCODE5) Required Note 1: - The reset network protects the device against parasitic resets. - The output of the external reset circuit must have an open-drain output to drive the ST7 reset pad. Otherwise the device can be damaged when the ST7 generates an internal reset (LVD or watchdog). - Whatever the reset source is (internal or external), the user must ensure that the level on the RESET pin can go below the VIL maximum level specified in section 13.9.1 on page 118. Otherwise the reset is not taken into account internally. - Because the reset circuit is designed to allow the internal RESET to be output in the RESET pin, the user must ensure that the current sunk on the RESET pin is less than the absolute maximum value specified for IINJ(RESET) in section 13.2.2 on page 99. Note 2: When the LVD is enabled, it is recommended not to connect a pull-up resistor or capacitor. A 10nF pull-down capacitor is required to filter noise on the reset line. Note 3: If a capacitive power supply is used, it is recommended to connect a 1M pull-down resistor to the RESET pin to discharge any residual voltage induced by the capacitive effect of the power supply (this adds 5A to the power consumption of the MCU). Note 4: Tips when using the LVD: - 1. Check that all recommendations related to ICCCLK and reset circuit have been applied (see caution in Table 1 on page 5 and notes above) - 2. Check that the power supply is properly decoupled (100nF + 10F close to the MCU). Refer to AN1709 and AN2017. If this cannot be done, it is recommended to put a 100nF + 1M pull-down on the RESET pin. - 3. The capacitors connected on the RESET pin and also the power supply are key to avoid any start-up marginality. In most cases, steps 1 and 2 above are sufficient for a robust solution. Otherwise: Replace 10nF pull-down on the RESET pin with a 5F to 20F capacitor." Note 5: Please refer to section 12.2.1 on page 95 for more details on illegal opcode reset conditions. 119/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.10 COMMUNICATION INTERFACE CHARACTERISTICS 13.10.1 SPI - Serial Peripheral Interface Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified. Symbol fSCK = 1 / tc(SCK) tr(SCK) tf(SCK) tsu(SS)1) th(SS)1) tw(SCKH)1) tw(SCKL)1) tsu(MI)1) tsu(SI)1) th(MI)1) th(SI)1) ta(SO)1) tdis(SO)1) tv(SO)1) th(SO)1) tv(MO)1) th(MO)1) Parameter SPI clock frequency SPI clock rise and fall time SS setup time4) SS hold time SCK high and low time Data input setup time Data input hold time Data output access time Data output disable time Data output valid time Data output hold time Data output valid time Data output hold time Slave Master Slave Master Slave Master Slave Slave Slave (after enable edge) Master (after enable edge) Refer to I/O port characteristics for more details on the input/output alternate function characteristics (SS, SCK, MOSI, MISO). Min fCPU / 128 = 0.0625 0 Max fCPU / 4 = 2 fCPU / 2 = 4 Unit MHz Conditions Master, fCPU = 8 MHz Slave, fCPU = 8 MHz See I/O port pin description (4 x TCPU) + 50 120 100 90 100 ns 0 120 240 120 120 0 0 Figure 96. SPI Slave Timing Diagram with CPHA = 03) SS INPUT tsu(SS) SCK INPUT CPHA = 0 CPOL = 0 CPHA = 0 CPOL = 1 ta(SO) MISO OUTPUT tw(SCKH) tw(SCKL) tv(SO) th(SO) tr(SCK) tf(SCK) LSB OUT tc(SCK) th(SS) tdis(SO) See note 2 See note 2 MSB OUT BIT6 OUT tsu(SI) th(SI) MOSI INPUT MSB IN BIT1 IN LSB IN Notes: 1. Data based on design simulation, not tested in production. 2. When no communication is on-going, the data output line of the SPI (MOSI in master mode, MISO in slave mode) has its alternate function capability released. In this case, the pin status depends on the I/O port configuration. 3. Measurement points are done at CMOS levels: 0.3 x VDD and 0.7 x VDD. 4. Depends on fCPU. For example, if fCPU = 8 MHz, then tCPU = 1 / fCPU = 125ns and tsu(SS) = 550ns. 120/138 ST7L15, ST7L19 COMMUNICATION INTERFACE CHARACTERISTICS (cont'd) Figure 97. SPI Slave Timing Diagram with CPHA = 11) SS INPUT tsu(SS) SCK INPUT CPHA = 1 CPOL = 0 CPHA = 1 CPOL = 1 ta(SO) tw(SCKH) tw(SCKL) tv(SO) th(SO) tr(SCK) tf(SCK) LSB OUT tc(SCK) th(SS) tdis(SO) MISO OUTPUT See note 2 HZ MSB OUT BIT6 OUT See note 2 tsu(SI) th(SI) MOSI INPUT MSB IN BIT1 IN LSB IN Figure 98. SPI Master Timing Diagram1) SS INPUT tc(SCK) CPHA = 0 CPOL = 0 SCK INPUT CPHA = 0 CPOL = 1 CPHA = 1 CPOL = 0 CPHA = 1 CPOL = 1 tw(SCKH) tw(SCKL) tsu(MI) MISO INPUT th(MI) tr(SCK) tf(SCK) MSB IN BIT6 IN LSB IN tv(MO) th(MO) MOSI OUTPUT See note 2 MSB OUT BIT6 OUT LSB OUT See note 2 Notes: 1. Measurement points are done at CMOS levels: 0.3 x VDD and 0.7 x VDD. 2. When no communication is on-going, the alternate function capability of the SPI's data output line (MOSI in master mode, MISO in slave mode) is released. In this case, the pin status depends on the I/O port configuration. 121/138 ST7L15, ST7L19 ELECTRICAL CHARACTERISTICS (cont'd) 13.11 10-BIT ADC CHARACTERISTICS Subject to general operating conditions for VDD, fOSC and TA unless otherwise specified. Symbol fADC VAIN RAIN CADC tSTAB tADC Parameter ADC clock frequency Conversion voltage range2) External input resistor Internal sample and hold capacitor Stabilization time after ADC enable Conversion time (Sample+Hold) - Sample capacitor loading time - Hold conversion time Analog part Digital part fCPU = 8 MHz, fADC = 4 MHz 6 04) 3.5 4 10 1 0.2 VSSA Conditions Min Typ1) Max 4 VDDA 103) Unit MHz V k pF s 1 / fADC mA IADC Figure 99. Typical Application with ADC VDD VT 0.6V RAIN VAIN VT 0.6V IL 1A AINx 10-bit A/D conversion CADC 6pF ST7 Notes: 1. Unless otherwise specified, typical data is based on TA = 25C and VDD - VSS = 5V. They are given only as design guidelines and are not tested. 2. When VDDA and VSSA pins are not available on the pinout, the ADC refers to VDD and VSS. 3. Any added external serial resistor downgrades the ADC accuracy (especially for resistance greater than 10k). Data based on characterization results, not tested in production. 4. The stabilization time of the AD converter is masked by the first tLOAD. The first conversion after the enable is then always valid. Related application notes Understanding and minimizing ADC conversion errors (AN1636) Software techniques for compensating ST7 ADC errors (AN1711) 122/138 ST7L15, ST7L19 10-BIT ADC CHARACTERISTICS (cont'd) Table 21. ADC Accuracy with 3V < VDD < 3.6V Symbol |ET| |EO| |EG| |ED| |EL| Parameter Total unadjusted error Offset error Gain error Differential linearity error Integral linearity error fCPU = 4 MHz, fADC = 2 MHz 1)2) Conditions Typ 2.8 0.25 0.6 2.9 2.6 Max3) 5.7 1.2 2.3 5.6 5.3 Unit LSB Table 22. ADC Accuracy with 4.5V < VDD < 5.5V Symbol |ET| |EO| |EG| |ED| |EL| Parameter Total unadjusted error Offset error Gain error Differential linearity error Integral linearity error fCPU = 8 MHz, fADC = 4 MHz1)2) Conditions Typ 4 3 1 1.5 Max3) 6 5 4 3 LSB Unit Notes: 1. Data based on characterization results over the whole temperature range, monitored in production. 2. ADC accuracy vs negative injection current: Injecting negative current on any of the analog input pins may reduce the accuracy of the conversion being performed on another analog input. The effect of negative injection current on robust pins is specified in section 13.11 on page 122 Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in section 13.8 on page 113 does not affect the ADC accuracy. 3. Data based on characterization results, monitored in production to guarantee 99.73% within max value from -40C to +125C ( 3 distribution limits). Figure 100. ADC Accuracy Characteristics Digital Result ADCDR 1023 1022 1021 1LSB IDEAL V -V DD SS = ------------------------------EG (1) Example of an actual transfer curve (2) The ideal transfer curve (3) End point correlation line 1024 (2) ET 7 6 5 4 3 2 1 0 VSS 1 2 3 4 1 LSBIDEAL EO EL ED (3) (1) ET = Total Unadjusted Error: maximum deviation between the actual and the ideal transfer curves. EO = Offset Error: deviation between the first actual transition and the first ideal one. EG = Gain Error: deviation between the last ideal transition and the last actual one. ED = Differential Linearity Error: maximum deviation between actual steps and the ideal one. EL = Integral Linearity Error: maximum deviation between any actual transition and the end point correlation line. Vin (LSBIDEAL) 5 6 7 1021 1022 1023 1024 VDD 123/138 ST7L15, ST7L19 14 PACKAGE CHARACTERISTICS In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard 14.1 PACKAGE MECHANICAL DATA Figure 101. 20-Pin Plastic Small Outline Package, 300-mil Width JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at www.st.com. D L A1 A a B e h x 45x Dim. c mm Min 2.35 0.10 0.33 0.23 12.60 7.40 1.27 10.00 0.25 0 0.40 10.65 0.394 0.75 0.010 8 0 1.27 0.016 Typ Max Min 2.65 0.093 0.30 0.004 0.51 0.013 0.32 0.009 13.00 0.496 7.60 0.291 inches Typ Max 0.104 0.012 0.020 0.013 0.512 0.299 0.050 0.419 0.030 8 0.050 A A1 B C D E e H h L N EH Number of Pins 20 Table 23. Thermal Characteristics Symbol RthJA TJmax PDmax Ratings Package thermal resistance (junction to ambient) Maximum junction temperature1) Power dissipation 2) Value 70 150 < 350 Unit C/W C mW Notes: 1. The maximum chip-junction temperature is based on technology characteristics. 2. The maximum power dissipation is obtained from the formula PD = (TJ -TA) / RthJA. The power dissipation of an application can be defined by the user with the formula: PD = PINT + PPORT, where PINT is the chip internal power (IDD x VDD) and PPORT is the port power dissipation depending on the ports used in the application. 124/138 ST7L15, ST7L19 PACKAGE CHARACTERISTICS (cont'd 14.2 SOLDERING INFORMATION In accordance with the RoHS European directive, all STMicroelectronics packages have been converted to lead-free technology, named ECOPACKTM. ECOPACKTM packages are qualified according to the JEDEC STD-020C compliant soldering profile. Detailed information on the STMicroelectronics ECOPACKTM transition program is available on www.st.com/stonline/leadfree/, with specific technical application notes covering the main technical aspects related to lead-free conversion (AN2033, AN2034, AN2035, AN2036). Forward compatibility: ECOPACKTM SO packages are fully compatible with a lead (Pb) containing soldering process (see application note AN2034). Table 24. Soldering Compatibility (wave and reflow soldering process) Package SO Plating Material NiPdAu (Nickel-Palladium-Gold) Pb Solder Paste Yes Pb-free Solder Paste Yes 125/138 ST7L15, ST7L19 15 DEVICE CONFIGURATION AND ORDERING INFORMATION Each device is available for production in user programmable versions (Flash) as well as in factory coded versions (ROM). ST7L1x devices are ROM versions. ST7PL1x devices are Factory Advanced Service Technique ROM (FASTROM) versions: They are factory programmed Flash devices. 15.1 OPTION BYTES The option bytes have no address in the memory map and are accessed only in programming mode (for example using a standard ST7 programming tool). Difference in option byte configuration beOPTION BYTE 0 4 3 2 ST7FL1x Flash devices are shipped to customers with a default program memory content (FFh), while ROM/FASTROM factory coded parts contain the code supplied by the customer. This implies that Flash devices have to be configured by the customer using the Option Bytes while the ROM/ FASTROM devices are factory-configured. tween Flash and ROM devices are presented in the following table and are described in Section 15.1.1 Flash Option Bytes and Section 15.1.2 ROM Option Bytes. OPTION BYTE 1 4 3 2 7 6 5 1 0 7 6 5 1 WDG SW 0 WDGHALT 1 WDGHALT 1 Name Flash Default value Reserved CLKSEL SEC SEC FMP FMP PLL PLL Res OSC 1 0 R W x4x8 OFF LVD 1:0 0 1 1 1 0 1 0 0 1 1 1 0 1 1 1 AWUCK Name ROM Default value OSCRANGE 2:0 Reserved ROP ROP PLL Res Res OSC _R _D OFF LVD 1:0 WDG SW 1 1 1 1 1 1 0 0 1 1 0 0 1 1 1 126/138 ST7L15, ST7L19 OPTION BYTES (cont'd) 15.1.1 Flash Option Bytes The 2 option bytes allow the hardware configuration of the microcontroller to be selected. OPTION BYTE 0 OPT7 = Reserved (must be set to 0) OPT6 = Reserved (must be set to 1) OPT5:4 = CLKSEL Clock Source Selection When the internal RC oscillator is not selected (Option OSC = 1), these option bits select the clock source: Resonator oscillator or external clock. CLKSEL Clock Source Resonator External clock source: CLKIN Reserved Port C 2 Ext. Osc Enabled/ Port C Disabled on PB4 Ext. Osc Disabled/ on PC0 Port C Enabled 0 0 1 1 1 0 1 1 0 Refer to the ST7 Flash Programming Reference Manual and section 4.5 on page 12 for more details. 0: Readout protection off 1: Readout protection on OPT 0 = FMP_W Flash write protection This option indicates if the Flash program memory is write protected. Warning: When this option is selected, the program memory (and the option bit itself) can never be erased or programmed again. 0: Write protection off 1: Write protection on OPTION BYTE 1 OPT7 = PLLx4x8 PLL Factor selection 0: PLLx4 1: PLLx8 OPT 6 = PLLOFF PLL Disable This option bit enables or disables the PLL. 0: PLL enabled 1: PLL disabled (bypassed) OPT 5 = Reserved (must be set to 1) OPT 4 = OSC RC Oscillator Selection This option bit enables to select the internal RC oscillator. 0: RC oscillator on 1: RC oscillator off Note: If the RC oscillator is selected, then to improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device. OPT 3:2 = LVD[1:0] Low Voltage Selection These option bits enable the voltage detection block (LVD) with a selected threshold to the LVD. Configuration LVD Off LVD High Threshold VD1 1 VD0 1 0 Note: When the internal RC oscillator is selected, the CLKSEL option bits must be kept at their default value in order to select the 256 clock cycle delay (see Section 7.5). OPT 3:2 = SEC[1:0] Sector 0 size definition These option bits indicate the size of sector 0 according to the following table. Sector 0 Size 0.5 Kbyte 0 1 Kbyte 2 Kbytes 1 4 Kbytes 1 1 0 SEC1 SEC0 0 OPT1 = FMP_R Readout protection Readout protection, when selected provides a protection against program memory content extraction and against write access to Flash memory. Erasing the option bytes when the FMP_R option is selected will cause the whole memory to be erased first and the device can be reprogrammed. 127/138 ST7L15, ST7L19 FLASH OPTION BYTES (cont'd) OPT 1 = WDGSW Hardware or Software Watchdog 0: Hardware (watchdog always enabled) 1: Software (watchdog to be enabled by software) OPT 0 = WDG HALT Watchdog Reset on Halt This option bit determines if a RESET is generated when entering HALT mode while the Watchdog is active. 0: No reset generation when entering HALT mode 1: Reset generation when entering HALT mode Table 25. List of Valid Option Combinations VDD range Operating conditions Clock Source Internal RC 1% 3.0 to 3.6V External clock or resonator (depending on OPT5:4 selection) PLL off x4 x8 off x4 x8 off x4 x8 off x4 x8 Typ fCPU 1 MHz @ 3.3V 4 MHz @ 3.3V 0 to 4 MHz 4 MHz 1 MHz @ 5V 8 MHz @ 5V 0 to 8 MHz 8 MHz OSC 0 1 0 0 1 1 Option Bits PLLOFF PLLx4x8 1 1 0 0 1 1 0 0 1 1 0 1 1 1 0 1 Internal RC 1% 4.5 to 5.5V External clock or resonator (depending on OPT5:4 selection) 128/138 ST7L15, ST7L19 OPTION BYTES (cont'd) 15.1.2 ROM Option Bytes The 2 option bytes allow the hardware configuration of the microcontroller to be selected. OPTION BYTE 0 OPT7 = AWUCK Auto Wake Up Clock Selection 0: 32 kHz oscillator (VLP) selected as AWU clock 1: AWU RC oscillator selected as AWU clock. Note: If this bit is reset, internal RC oscillator must be selected (Option OSC = 0). OPT6:4 = OSCRANGE[2:0] Oscillator Range When the internal RC oscillator is not selected (Option OSC = 1), these option bits select the range of the resonator oscillator current source or the external clock source. Note: OSCRANGE[2:0] has no effect when AWUCK option is set to 0. In this case, the VLP oscillator range is automatically selected as AWU clock. OSCRANGE 2 LP MP Typ. frequency range with MS resonator HS 1~2 MHz 2~4 MHz 4~8 MHz 8~16 MHz 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 0 0 1 0 1 0 1 0 OPTION BYTE 1 OPT 7 = Reserved (must be set to 1) OPT 6 = PLLOFF PLL Disable This option bit enables or disables the PLL. 0: PLL enabled 1: PLL disabled (bypassed) OPT 5 = Reserved (must be set to 0) OPT 4 = OSC RC Oscillator Selection This option bit is used to select the internal RC oscillator. 0: RC oscillator on 1: RC oscillator off Note: If the RC oscillator is selected, then to improve clock stability and frequency accuracy, it is recommended to place a decoupling capacitor, typically 100nF, between the VDD and VSS pins as close as possible to the ST7 device. OPT 3:2 = LVD[1:0] Low Voltage Selection These option bits enable the voltage detection block (LVD) with a selected threshold to the LVD. Configuration LVD Off LVD High Threshold VD1 1 VD0 1 0 VLP 32.768~ kHz External clock on OSC1 Reserved OPT 3:2 = Reserved (must be set to 1:1) OPT1 = ROP_R Readout protection for ROM This option is for read protection of ROM 0: Readout protection off 1: Readout protection on OPT 0 = ROP_D Readout protection for Data EEPROM This option is for read protection of EEPROM memory. 0: Readout protection off 1: Readout protection on OPT 1 = WDGSW Hardware or Software Watchdog 0: Hardware (watchdog always enabled) 1: Software (watchdog to be enabled by software) OPT 0 = WDG HALT Watchdog Reset on Halt This option bit determines if a RESET is generated when entering HALT mode while the Watchdog is active. 0: No reset generation when entering HALT mode 1: Reset generation when entering HALT mode 129/138 ST7L15, ST7L19 DEVICE CONFIGURATION AND ORDERING INFORMATION (cont'd) 15.2 DEVICE ORDERING INFORMATION Figure 102. Flash Commercial Product Code Structure DEVICE E2DATA PINOUT PROG MEM PACKAGE VERSION TR E E = Leadfree (ECOPACKTM option) Conditioning options: TR = Tape and Reel (left blank if Tube) A = -40 to +85C C = -40 to +125C M = Plastic Small Outline 1 = 4 Kbytes F = 20 pins 5 = No E2 data 9 = E2 data (128 bytes) ST7FL1 Table 26. Flash User Programmable Device Types Part Number ST7FL15F1MAE ST7FL19F1MAE ST7FL15F1MCE ST7FL19F1MCE 4K Flash 256 Program Memory (bytes) RAM (bytes) Data EEPROM (bytes) 128 128 Temperature Range -40 to +85C SO20 -40 to +125C Package 130/138 ST7L15, ST7L19 DEVICE CONFIGURATION AND ORDERING INFORMATION (cont'd) Figure 103. FASTROM Commercial Product Code Structure DEVICE E2DATA PINOUT PROG MEM PACKAGE VERSION / XXX R E E = Leadfree (ECOPACKTM option) Conditioning options: R = Tape and Reel (left blank if Tube) Code name (defined by STMicrolectronics) Not present if Tape and Reel A = -40 to +85C C = -40 to +125C M = Plastic Small Outline 1 = 4 Kbytes F = 20 pins 5 = No E2 data 9 = E2 data (128 bytes) ST7PL1 Table 27. FASTROM Factory Coded Device Types Part Number ST7PL15F1MAE ST7PL19F1MAE ST7PL15F1MCE ST7PL19F1MCE 4K FASTROM 256 Program Memory (bytes) RAM (bytes) Data EEPROM (bytes) 128 128 Temperature Range -40 to +85C SO20 -40 to +125C Package 131/138 ST7L15, ST7L19 DEVICE CONFIGURATION AND ORDERING INFORMATION (cont'd) Figure 104. ROM Commercial Product Code Structure DEVICE E2DATA PINOUT PROG MEM PACKAGE / XXX R E E = Leadfree (ECOPACKTM option) Conditioning options: R = Tape and Reel (left blank if Tray) Code name (defined by STMicroelectronics) M = Plastic Small Outline 1 = 4 Kbytes F = 20 pins 5 = No E2 data 9 = E2 data (128 bytes) ST7L1 Table 28. ROM Factory Coded Device Types Part Number ST7L15F1MAE ST7L19F1MAE ST7L15F1MCE ST7L19F1MCE 4K ROM 256 Program Memory (bytes) RAM (bytes) Data EEPROM (bytes) 128 128 Temperature Range -40 to +85C SO20 -40 to +125C Package 132/138 ST7L15, ST7L19 ST7L1 FASTROM & ROM MICROCONTROLLER OPTION LIST (Last update: December 2006) Customer Address .......................................................................... .......................................................................... .......................................................................... Contact .......................................................................... Phone No .......................................................................... Reference FASTROM Code*:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . *FASTROM code name is assigned by STMicroelectronics. FASTROM code must be sent in .S19 format. .Hex extension cannot be processed. Device Type/Memory Size/Package (check only one option): -----------------------------------------------------------------------------FASTROM / 4 Kbytes / SO20 ROM / 4 Kbytes / SO20 ----------------------------------------------------------------------------[ ] ST7PL15F1M [ ] ST7L15F1M [ ] ST7PL19F1M [ ] ST7L19F1M Conditioning (check only one option):[ ] Tape & Reel [ ] Tube Special Marking: [ ] No [ ] Yes "_ _ _ _ _ _ _ _ " (8 char. max) Authorized characters are letters, digits, '.', '-', '/' and spaces only. Temperature range: PLL: LVD Reset: Watchdog Selection: Watchdog Reset on Halt: Flash Devices only Clock Source Selection: [ ] A (-40C to +85C) [ ] Disabled [ ] Disabled [ ] Software Activation [ ] Disabled [ ] Resonator [ ] External clock [ ] on PB4 [ ] on OSC1 [ ] Internal RC oscillator [ ] 0.5 Kbyte [ ] Disabled [ ] Disabled [ ] 1 Kbyte [ ] Enabled [ ] Enabled [ ] 2 Kbytes [ ] 4 Kbytes [ ] C (-40C to +125C) [ ] Enabled [ ] Enabled (highest voltage threshold) [ ] Hardware Activation [ ] Enabled Sector 0 size: Readout Protection: Flash Write Protection: ROM Devices only Clock Source Selection: [ ] Resonator [ ] VLP: Very Low power resonator (32 to 100 kHz) [ ] LP: Low power resonator (1 to 2 MHz) [ ] MP: Medium power resonator (2 to 4 MHz) [ ] MS: Medium speed resonator (4 to 8 MHz) [ ] HS: High speed resonator (8 to 16 MHz) [ ] External clock [ ] on PB4 [ ] on OSC1 [ ] Internal RC oscillator [ ] 32 kHz oscillator [ ] Disabled [ ] Disabled [ ] AWU RC oscillator [ ] Enabled [ ] Enabled AWUCK Selection Readout Protection for ROM: Readout Protection for E2data: Comments: Supply operating range in the application: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Notes: .......................................................................... Date: .......................................................................... Signature: ....................................................................................... Important note: Not all configurations are available. See section 15.1 on page 126 for authorized option byte combinations. 133/138 1 ST7L15, ST7L19 DEVICE CONFIGURATION AND ORDERING INFORMATION (cont'd) 15.3 DEVELOPMENT TOOLS Development tools for the ST7 microcontrollers include a complete range of hardware systems and software tools from STMicroelectronics and thirdparty tool suppliers. The range of tools includes solutions to help you evaluate microcontroller peripherals, develop and debug your application, and program your microcontrollers. 15.3.1 Evaluation Tools and Starter Kits ST offers complete, affordable starter kits and full-featured evaluation boards that allow you to evaluate microcontroller features and quickly start developing ST7 applications. Starter kits are complete, affordable hardware/software tool packages that include features and samples to help you quickly start developing your application. ST evaluation boards are open-design, embedded systems, which are developed and documented to serve as references for your application design. They include sample application software to help you demonstrate, learn about and implement your ST7's features. 15.3.2 Development and Debugging Tools Application development for ST7 is supported by fully optimizing C Compilers and the ST7 Assembler-Linker toolchain, which are all seamlessly integrated in the ST7 integrated development environments in order to facilitate the debugging and fine-tuning of your application. The Cosmic C Compiler is available in a free version that outputs up to 16 Kbytes of code. The range of hardware tools includes full-featured ST7-EMU3 series emulators, cost effective ST7DVP3 series emulators and the low-cost RLink in-circuit debugger/programmer. These tools are supported by the ST7 Toolset from STMicroelectronics, which includes the STVD7 integrated development environment (IDE) with high-level language debugger, editor, project manager and integrated programming interface. 15.3.3 Programming Tools During the development cycle, the ST7-DVP3 and ST7-EMU3 series emulators and the RLink provide in-circuit programming capability for programming the Flash microcontroller on your application board. ST also provides dedicated a low-cost dedicated in-circuit programmer, the ST7-STICK, as well as ST7 Socket Boards which provide all the sockets required for programming any of the devices in a specific ST7 sub-family on a platform that can be used with any tool with in-circuit programming capability for ST7. For production programming of ST7 devices, ST's third-party tool partners also provide a complete range of gang and automated programming solutions, which are ready to integrate into your production environment. 15.3.4 Order Codes for Development and Programming Tools Table 29 below lists the ordering codes for the ST7L1 development and programming tools. For additional ordering codes for spare parts and accessories, refer to the online product selector at www.st.com/mcu. Table 29. ST7L1 Development and Programming Tools Supported Products In-circuit Debugger, RLink Series1) Starter Kit without Demo Board STX-RLINK2)6) Emulator DVP Series EMU Series Programming Tool In-circuit Programmer ST7-STICK3)5) STX-RLINK6) ST Socket Boards and EPBs ST7SB10-1233) ST7FL15 ST7FL19 ST7MDT10-DVP34) ST7MDT10-EMU3 Notes: 1. Available from ST or from Raisonance, www.raisonance.com 2. USB connection to PC 3. Add suffix /EU, /UK or /US for the power supply for your region 4. Includes connection kit for DIP16/SO16 only. See "How to order an EMU or DVP" in ST product and tool selection guide for connection kit ordering information 5. Parallel port connection to PC 6. RLink with ST7 tool set 134/138 ST7L15, ST7L19 15.4 ST7 APPLICATION NOTES All relevant ST7 application notes can be found on www.st.com. 135/138 ST7L15, ST7L19 16 REVISION HISTORY Table 30. Revision History Date 16-Aug-2006 Revision 1 Initial release Replaced "ST7L1" with "ST7L15, ST7L19" in document name on page 1 Added "Features" heading above list of features on page 1 "Clock, Reset and Supply Management" on page 1: Removed AVD feature Changed section 1 on page 4 Figure 1 on page 4: - removed AVD - replaced Autoreload Timer 2 with Autoreload Timer 4 - referenced Port C to figure footnote Table 2 on page 8: - replaced Autoreload Timer 2 with Autoreload Timer 4 - added "1" to register name and register label of AT4 counter register Section 7 SUPPLY, RESET AND CLOCK MANAGEMENT features: - changed Clock Management feature - removed AVD from SI Management feature Changed Section 7.4 MULTI-OSCILLATOR (MO) Section 7.6 SYSTEM INTEGRITY MANAGEMENT (SI): Removed mention of AVD function from first paragraph Added caution about avoiding unwanted behavior during Reset sequence in section 7.5.1 on page 25 Figure 12 on page 23: Removed lock32 from bit 7 in SICSR Figure 17 on page 29: Removed AVD from bits 1:0 in SICSR Removed Section 7.6.2 Auxiliary Voltage Detector (AVD) Removed Section 7.6.2.1 Monitoring the VDD Main Supply Removed Figure 18. Using the AVD to Monitor VDD from Section 7 Section 7.6.2 Low-Power Modes: Removed AVD references Removed Section 7.6.3.1 Interrupts Section 7.6.3 Register Description: Changed bits 1:0 to reserved in SICSR Changed section 11.2 on page 52: Replaced AT3 with AT4 Changed description of bits 11:0 of CNTR register in section 11.2.6 on page 65 Table 5, "Interrupt Mapping," on page 32: Changed description of interrupt No. 7 Section 13.3.2 Operating Conditions with Low Voltage Detector (LVD): Removed AVD from current consumption Removed Section 13.3.3 Auxiliary Voltage Detector (AVD) Thresholds Section 13.4.1 Supply Current: Changed typical and max values for AWUFH Section 13.4.1 Supply Current: Changed typical value for ACTIVE HALT Table 21, "ADC Accuracy with 3V < VDD < 3.6V," on page 123: Changed typical and maximum values Table 22, "ADC Accuracy with 4.5V < VDD < 5.5V," on page 123: Redistributed max value footnote links Table 23, "Thermal Characteristics," on page 124: Changed package thermal resistance and power dissapation values Removed text concerning Pb-containing packages from section 14.2 on page 125 Table 24 on page 125: - changed title of "Plating Material" column - removed note concerning Pb-package temperature for leadfree soldering compatibility Changed Section 15 DEVICE CONFIGURATION AND ORDERING INFORMATION Main changes 20-Dec-2006 2 136/138 ST7L15, ST7L19 Table 30. Revision History Date Revision Main changes Section 15.2 DEVICE ORDERING INFORMATION: - removed Table 26, "Supported Part Numbers" - added Figure 102. Flash Commercial Product Code Structure - added Table 26, "Flash User Programmable Device Types," on page 130 - added Figure 103. FASTROM Commercial Product Code Structure - added Table 27, "FASTROM Factory Coded Device Types," on page 131 - added Figure 104. ROM Commercial Product Code Structure - added Table 28, "ROM Factory Coded Device Types," on page 132 Updated option list on page 133 Changed section 15.4 on page 135: Removed Table 28 ST7 Application Notes and added a statement to indicate that application notes can be found on the ST website Corrected revision number on page 1 (previous revision 2 inadvertently stated Rev. 1 at bottom of cover page) 20-Dec-2006 2 15-Jan-2007 3 137/138 ST7L15, ST7L19 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 138/138 |
Price & Availability of ST7FL15F1MATRE |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |