Part Number Hot Search : 
SD10195 CZMK20V KDR41208 TDA6190T AT54A ISL976 EGP08A
Product Description
Full Text Search
 

To Download MC3334106 Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 MC33341 Power Supply Battery Charger Regulation Control Circuit
The MC33341 is a monolithic regulation control circuit that is specifically designed to close the voltage and current feedback loops in power supply and battery charger applications. This device features the unique ability to perform source high-side, load high-side, source low-side and load low-side current sensing, each with either an internally fixed or externally adjustable threshold. The various current sensing modes are accomplished by a means of selectively using the internal differential amplifier, inverting amplifier, or a direct input path. Positive voltage sensing is performed by an internal voltage amplifier. The voltage amplifier threshold is internally fixed and can be externally adjusted in all low-side current sensing applications. An active high drive output is provided to directly interface with economical optoisolators for isolated output power systems. This device is available in 8-lead dual-in-line and surface mount packages.
Features http://onsemi.com MARKING DIAGRAMS
8 SOIC-8 D SUFFIX CASE 751 1 33341 ALYW G
1
8 PDIP-8 P SUFFIX CASE 626 1 1 MC33341P AWL YYWWG
* * * * * * * * * *
Differential Amplifier for High-Side Source and Load Current Sensing Inverting Amplifier for Source Return Low-Side Current Sensing Non-Inverting Input Path for Load Low-Side Current Sensing Fixed or Adjustable Current Threshold in All Current Sensing Modes Positive Voltage Sensing in All Current Sensing Modes Fixed Voltage Threshold in All Current Sensing Modes Adjustable Voltage Threshold in All Low-Side Current Sensing Modes Output Driver Directly Interfaces with Economical Optoisolators Operating Voltage Range of 2.3 V to 16 V Pb-Free Packages are Available
Drive Output 8 VCC 7 Current Sense Input B/ Voltage Sense Input Voltage Threshold Adjust 6 5
A = Assembly Location L, WL = Wafer Lot Y, YY = Year W, WW = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location)
PIN CONNECTIONS
Current Sense Input A 1 Current Threshold Adjust 2
8 Drive Output 7 VCC 6 Voltage Threshold Adjust 5 Voltage Sense Input (Top View)
Current Sense Input B/
Differential Amp 1.0
Voltage and Current Transconductance Amp/Driver V 1.2 V
Compensation 3
GND 4
#1.0 0.2 V Inverting/ Noninverting Amp
I Reference
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 17 of this data sheet.
1 Current Sense Input A
2 3 Current Compensation Threshold Adjust This device contains 114 active transistors.
4 GND
Figure 1. Representative Block Diagram
(c) Semiconductor Components Industries, LLC, 2006
1
August, 2006 - Rev. 4
Publication Order Number: MC33341/D
MC33341
MAXIMUM RATINGS
Rating Power Supply Voltage (Pin 7) Symbol VCC VIR Value 16 Unit V V
AAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA A A A A AAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAA A A A A A A A A A A AAAAAAAAAAAAAAAAAAA AAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAA A A A A A AAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A
Voltage Range Current Sense Input A (Pin 1) Current Threshold Adjust (Pin 2) Compensation (Pin 3) Voltage Sense Input (Pin 5) Current Sense Input B / Voltage Threshold Adjust (Pin 6) Drive Output (Pin 8) Drive Output Source Current (Pin 8) -1.0 to VCC ISource RqJA 50 mA Thermal Resistance, Junction-to-Air P Suffix, DIP Plastic Package, Case 626 D Suffix, SO-8 Plastic Package, Case 751 Operating Junction Temperature (Note 1) Storage Temperature C/W 100 178 TJ -25 to +150 -55 to +150 C C Tstg NOTE: ESD data available upon request. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Tested ambient temperature range for the MC33341: Tlow = -25C, Thigh = +85C.
ELECTRICAL CHARACTERISTICS (VCC = 6.0 V, TA = 25C, for min/max values TA is the operating junction temperature range that
applies (Note 1), unless otherwise noted.) Characteristic CURRENT SENSING (Pins 1, 2, 6) Symbol Min Typ Max Unit
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
High-Side Source and Load Sensing Pin 1 to Pin 6 (Pin 1 >1.6 V) Internally Fixed Threshold Voltage (Pin 2 = VCC) TA = 25C TA = Tlow to Thigh Externally Adjusted Threshold Voltage (Pin 2 = 0 V) Externally Adjusted Threshold Voltage (Pin 2 = 200 mV) Low-Side Load Sensing Pin 1 to Pin 4 (Pin 1 = 0 V to 0.8 V) Internally Fixed Threshold Voltage (Pin 2 = VCC) TA = 25C TA = Tlow to Thigh Externally Adjusted Threshold Voltage (Pin 2 = 0 V) Externally Adjusted Threshold Voltage (Pin 2 = 200 mV) Vth(I HS) mV 187 183 - - 197 - 10 180 207 211 - -
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA
Vth(I LS+) mV
AAA A A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAA AAA A A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA
Current Sense Input A (Pin 1) Input Bias Current, High-Side Source and Load Sensing (Pin 2 = 0 V to VPin 6 V) Input Bias Current, Low-Side Load Sensing (Pin 2 = 0 V to 0.8 V) Input Resistance, Low-Side Source Return Sensing (Pin 2 = -0.6 V to 0 V) IIB(A HS) - - - 40 10 10 - - - mA IIB(A LS+) nA Rin(A LS-) IIB(B) kW Current Sense Input B/Voltage Threshold Adjust (Pin 6) Input Bias Current High-Side Source and Load Current Sensing (Pin 6 > 2.0 V) Voltage Threshold Adjust (Pin 6 < 1.2 V) Current Sense Threshold Adjust (Pin 2) Input Bias Current - - - - 20 100 10 - - - - mA nA nA IIB(I th) gm(I) Transconductance, Current Sensing Inputs to Drive Output 6.0 mhos Low-Side Source Return Sensing Pin 1 to 4 (Pin 1 = 0 V to -0.2 V) Internally Fixed Threshold Voltage (Pin 2 = VCC) TA = 25C TA = Tlow to Thigh Externally Adjusted Threshold Voltage (Pin 2 = 0 V) Externally Adjusted Threshold Voltage (Pin 2 = 200 mV) Vth(I LS-) mV -195 -193 - - -201 - -10 -180 -207 -209 - -
194 192 - -
200 - 10 180
206 208 - -
http://onsemi.com
2
MC33341
ELECTRICAL CHARACTERISTICS (VCC = 6.0 V, TA = 25C, for min/max values TA is the operating junction temperature range that
applies (Note 1), unless otherwise noted.)
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
DIFFERENTIAL AMPLIFIER DISABLE LOGIC (Pins 1, 6) Logic Threshold Voltage Pin 1 (Pin 6 = 0 V) Enabled, High-Side Source and Load Current Sensing Disabled, Low-Side Load and Source Return Current Sensing V Vth(I HS) Vth(I LS) Vth(V) - - 1.7 1.3 - - VOLTAGE SENSING (Pins 5, 6) Positive Sensing Pin 5 to Pin 4 Internally Fixed Threshold Voltage TA = 25C TA = Tlow to Thigh Externally Adjusted Threshold Voltage (Pin 6 = 0 V) Externally Adjusted Threshold Voltage (Pin 6 = 1.2 V) Voltage Sense, Input Bias Current (Pin 5) 1.186 1.174 - - - - 1.210 - 40 1.175 10 7.0 1.234 1.246 - - - - V V mV V nA
Characteristic
Symbol
Min
Typ
Max
Unit
AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAA A A AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAA
IIB(V) Transconductance, Voltage Sensing Inputs to Drive Output gm(V) VOH mhos DRIVE OUTPUT (Pin 8) High State Source Voltage (ISource = 10 mA) High State Source Current (Pin 8 = 0 V) - VCC - 0.8 20 - - V ISource VCC ICC 15 mA TOTAL DEVICE (Pin 7) Operating Voltage Range 2.5 to 15 - 2.3 to 15 300 - V Power Supply Current (VCC = 6.0 V) 600 mA
PIN FUNCTION DESCRIPTION
Pin 1 Name
Description
AAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A A AAA AAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAA A A A A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A
Current Sense Input A This multi-mode current sensing input can be used for either source high-side, load high-side, source-return low-side, or load low-side sensing. It is common to a Differential Amplifier, Inverting Amplifier, and a Noninverting input path. Each of these sensing paths indirectly connect to the current sense input of the Transconductance Amplifier. This input is connected to the high potential side of a current sense resistor when used in source high-side, load high-side, or load low-side current sensing modes. In source return low-side current sensing mode, this pin connects to the low potential side of a current sense resistor. The current sense threshold can be externally adjusted over a range of 0 V to 200 mV with respect to Pin 4, or internally fixed at 200 mV by connecting Pin 2 to VCC. 2 3 Current Threshold Adjust Compensation This pin is connected to a high impedance node within the transconductance amplifier and is made available for loop compensation. It can also be used as an input to directly control the Drive Output. An active low at this pin will force the Drive Output into a high state. This pin is the regulation control IC ground. The control threshold voltages are with respect to this pin. This is the voltage sensing input of the Transconductance Amplifier. It is normally connected to the power supply/battery charger output through a resistor divider. The input threshold is controlled by Pin 6. 4 5 Ground Voltage Sense Input 6 Current Sense Input B / Voltage Threshold Adjust This is a dual function input that is used for either high-side current sensing, or as a voltage threshold adjustment for Pin 5. This input is connected to the low potential side of a current sense resistor when used in source high-side or load high-side current sensing modes. In all low-side current sensing modes, Pin 6 is available as a voltage threshold adjustment for Pin 5. The threshold can be externally adjusted over a range of 0 V to 1.2 V with respect to Pin 4, or internally fixed at 1.2 V by connecting Pin 6 to VCC. This is the positive supply voltage for the regulation control IC. The typical operating voltage range is 2.3 V to 15 V with respect to Pin 4. This is a source-only output that normally connects to a linear or switching regulator control circuit. This output is capable of 15 mA, allowing it to directly drive an optoisolator in primary side control applications where galvanic isolation is required. 7 8 VCC Drive Output
http://onsemi.com
3
MC33341
Vth(v) , VOLTAGE SENSING THRESHOLD CHANGE (mV) 4.0 VCC = 6.0 V 0 V th(I HS), CURRENT SENSING THRESHOLD CHANGE (mV) 0 1.0 VCC = 6.0 V
-4.0
-1.0 3 -2.0 1 - Source High-Side and Load High-Side 2 - Source Return Low-Side 3 - Load Low-Side -25 0 25 50 75 100 2 1
-8.0
-12 -50
-25
0
25
50
75
100
125
-3.0 -50
125
TA, AMBIENT TEMPERATURE (C)
TA, AMBIENT TEMPERATURE (C)
Figure 2. Voltage Sensing Threshold Change versus Temperature
Figure 3. Current Sensing Threshold Change versus Temperature
V Pin 6 -V Pin 5 , INPUT DIFFERENCE VOLTAGE (mV)
1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0
VCC = 6.0 V VO = 1.0 V IO = 1.0 mA TA = 25C VPin 5
V Pin 6 , CURRENT SENSE INPUT B (mV)
V Pin 5 , VOLTAGE SENSING INPUT (V)
1.6
16 14 12 10 8.0 6.0 4.0 VPin 6-VPin 5 0.2 0.4 0.6 0.8 1.0 1.2 1.4 2.0 0 1.6
0 -40 -80 -120 -160 -200 -240 -280 0
Differential Amplifier is active for source high-side and load high-side current sensing. Both vertical axis are expressed in millivolts down to VCC.
0 VCC VPin 1-VPin 6 VPin 6 VCC = 6.0 V VO = 1.0 V IO = 1.0 mA Pin 1 = VCC TA = 25C 4.0 6.0 8.0 10 12 160 200 240 14 280 2.0
40
80
120
VPin 6, VOLTAGE THRESHOLD ADJUST (V)
VPin 2, CURRENT THRESHOLD ADJUST (V)
Figure 4. Closed-Loop Voltage Sensing Input versus Voltage Threshold Adjust
Figure 5. Closed-Loop Current Sense Input B versus Current Threshold Adjust
V Pin 1, CURRENT SENSE INPUT A (mV)
240 200 160 120 80
Noninverting input path is active for load low-side current sensing. VCC = 6.0 V VO = 1.0 V IO = 1.0 mA TA = 25C VPin 5 VPin 2-VPin 1
V Pin 1, CURRENT SENSE INPUT A (mV)
280
14 12 10 8.0 6.0 4.0 GND 2.0 0 280
0 -40 -80 -120 -160 -200 -240 -260 0 40 80 120 VPin 2-|VPin 1| VPin 5 GND VCC = 6.0 V VO = 1.0 V IO = 1.0 mA TA = 25C
14 12 10 8.0 6.0 4.0 Inverting Amplifier is 2.0 active for source return low-side current sensing. 0 160 200 240 280
40 0 0 40 80 120 160 200
240
VPin 2, CURRENT THRESHOLD ADJUST (mV)
VPin 2, CURRENT THRESHOLD ADJUST (mV)
Figure 6. Closed-Loop Current Sensing Input A versus Current Threshold Adjust
Figure 7. Closed-Loop Current Sensing Input A versus Current Threshold Adjust
http://onsemi.com
4
V Pin 2 -|V Pin 1 |, INPUT DIFFERENCE VOLTAGE (mV)
V Pin 2 -V Pin 1, INPUT DIFFERENCE VOLTAGE (mV)
V Pin 1 -V Pin 6 , INPUT DIFFERENCE VOLTAGE (mV)
MC33341
A VOL(V) , VOLTAGE SENSING OPEN-LOOP VOLTAGE GAIN (dB) 60 80 50 40 120 30 20 10 0 1.0 k VCC = 6.0 V VO = 1.0 V RL = 1.0 k Pin 3 = 1.0 nF TA = 25C 10 k 100 k Gain 140 160 180 1.0 M 100 , EXCESS PHASE () Phase A VOL(I), CURRENT SENSING OPEN-LOOP VOLTAGE GAIN (dB) 60 80 50 40 120 30 20 10 VCC = 6.0 V VO = 1.0 V RL = 1.0 k Pin 3 = 1.8 nF TA = 25C 10 k 100 k Gain 140 160 180 1.0 M 100 , EXCESS PHASE () Phase Low-Side Sensing Phase High-Side Sensing
0 1.0 k
f, FREQUENCY (Hz)
f, FREQUENCY (Hz)
Figure 8. Bode Plot Voltage Sensing Inputs to Drive Output
g m(v) , VOLTAGE SENSING TRANSCONDUCTANCE (mhos) g m(I), CURRENT SENSING TRANSCONDUCTANCE (mhos)
Figure 9. Bode Plot Current Sensing Inputs to Drive Output
8.0 VCC = 6.0 V VO = 1.0 V TA = 25C
8.0 VCC = 6.0 V VO = 1.0 V TA = 25C
6.0
6.0
4.0
4.0
2.0
2.0
0 0.1
0.2
0.3
0.5
1.0
2.0
3.0
5.0
10
0 0.1
0.2
0.3
0.5
1.0
2.0
3.0
5.0
10
IO, DRIVE OUTPUT LOAD CURRENT (mA)
IO, DRIVE OUTPUT LOAD CURRENT (mA)
Figure 10. Transconductance Voltage Sensing Inputs to Drive Output
I CC, SUPPLY CURRENT, DRIVE OUTPUT LOW STATE (mA)
Figure 11. Transconductance Current Sensing Inputs to Drive Output
V OH , OUTPUT SOURCE SATURATION VOLTAGE (V)
0 VCC -0.4 -0.8 -1.2 -1.6 -2.0 0 VCC = 6.0 V TA = 25C
1.0 Drive Output High State 0.8 0.6 0.4 0.2 0 0 IO = 0 mA TA = 25C Drive Output Low State
4.0
8.0
12
16
20
4.0
8.0 VCC, SUPPLY VOLTAGE (V)
12
16
IL, OUTPUT LOAD CURRENT (mA)
Figure 12. Drive Output High State Source Saturation versus Load Current
Figure 13. Supply Current versus Supply Voltage
http://onsemi.com
5
MC33341
INTRODUCTION Power supplies and battery chargers require precise control of output voltage and current in order to prevent catastrophic damage to the system load. Many present day power sources contain a wide assortment of building blocks and glue devices to perform the required sensing for proper regulation. Typical feedback loop circuits may consist of a voltage and current amplifier, level shifting circuitry, summing circuitry and a reference. The MC33341 contains all of these basic functions in a manner that is easily adaptable to many of the various power source-load configurations. OPERATING DESCRIPTION The MC33341 is an analog regulation control circuit that is specifically designed to simultaneously close the voltage and current feedback loops in power supply and battery charger applications. This device can control the feedback loop in either constant-voltage or constant-current mode with automatic crossover. A concise description of the integrated circuit blocks is given below. Refer to the block diagram in Figure 14.
Transconductance Amplifier
current sensing modes, Pin 6 is available, and can be used to lower the regulation threshold of Pin 5. This threshold can be externally adjusted over a range of 0 V to 1.2 V with respect to the IC ground at Pin 4.
Current Sensing
A quad input transconductance amplifier is used to control the feedback loop. This amplifier has separate voltage and current channels, each with a sense and a threshold input. Within a given channel, if the sense input level exceeds that of the threshold input, the amplifier output is driven high. The channel with the largest difference between the sense and threshold inputs will set the output source current of the amplifier and thus dominate control of the feedback loop. The amplifier output appears at Pin 8 and is a source-only type that is capable of 15 mA. A high impedance node within the transconductance amplifier is made available at Pin 3 for loop compensation. This pin can sink and source up to 10 mA of current. System stability is achieved by connecting a capacitor from Pin 3 to ground. The Compensation Pin signal is out of phase with respect to the Drive Output. By actively clamping Pin 3 low, the Drive Output is forced into a high state. This, in effect, will shutdown the power supply or battery charger, by forcing the output voltage and current regulation threshold down towards zero.
Voltage Sensing
Current sensing is accomplished by monitoring the voltage that appears across sense resistor RS, level shifting it with respect to Pin 4 if required, and applying it to the noninverting Isen input of the transconductance amplifier. In order to allow for maximum circuit flexibility, there are three methods of current sensing, each with different internal paths. In source high-side (Figures 14 and 15) and load high-side (Figures 18 and 19) current sensing, the Differential Amplifier is active with a gain of 1.0. Pin 1 connects to the high potential side of current sense resistor RS while Pin 6 connects to the low side. Logic circuitry is provided to disable the Differential Amplifier output whenever low-side current sensing is required. This circuit clamps the Differential Amplifier output high which disconnects it from the Isen input of the Transconductance Amplifier. This happens if Pin 1 is less than 1.2 V or if Pin 1 is less than Pin 6. With source return low-side current sensing (Figures 16 and 17), the Inverting Amplifier is active with a gain of -1.0. Pin 1 connects to the low potential side of current sense resistor RS while Pin 4 connects to the high side. Note that a negative voltage appears across RS with respect to Pin 4. In load low-side current sensing (Figures 20 and 21) a Noninverting input path is active with a gain of 1.0. Pin 1 connects to the high potential side of current sense resistor RS while Pin 4 connects to the low side. The Noninverting input path lies from Pin 1, through the Inverting Amplifier input and feedback resistors R, to the cathode of the output diode. With load low-side current sensing, Pin 1 will be more positive than Pin 4, forcing the Inverting Amplifier output low. This causes the diode to be reverse biased, thus preventing the output stage of the amplifier from loading the input signal that is flowing through the feedback resistors. The regulation threshold in all of the current sensing modes is internally fixed at 200 mV with Pin 2 connected to VCC. Pin 2 can be used to externally adjust the threshold over a range of 0 to 200 mV with respect to the IC ground at Pin 4.
Reference
The voltage that appears across the load is monitored by the noninverting Vsen input of the transconductance amplifier. This voltage is resistively scaled down and connected to Pin 5. The threshold at which voltage regulation occurs is set by the level present at the inverting Vth input of the transconductance amplifier. This level is controlled by Pin 6. In source high-side and load high-side current sensing modes, Pin 6 must be connected to the low potential side of current sense resistor RS. Under these conditions, the voltage regulation threshold is internally fixed at 1.2 V. In source return low-side and load low-side
An internal band gap reference is used to set the 1.2 V voltage threshold and 200 mV current threshold. The reference is initially trimmed to a 1.0% tolerance at TA = 25C and is guaranteed to be within 2.0% over an ambient operating temperature range of -25 to 85C.
Applications
Each of the application circuits illustrate the flexibility of this device. The circuits shown in Figures 14 through 21 contain an optoisolator connected from the Drive Output at
http://onsemi.com
6
MC33341
Pin 8 to ground. This configuration is shown for ease of understanding and would normally be used to provide an isolated control signal to a primary side switching regulator controller. In non-isolated, primary or secondary side applications, a load resistor can be placed from Pin 8 to ground. This resistor will convert the Drive Output current to a voltage for direct control of a regulator. In applications where excessively high peak currents are possible from the source or load, the load induced voltage
Source RS
drop across RS could exceed 1.6 V. Depending upon the current sensing configuration used, this will result in forward biasing of either the internal VCC clamp diode, Pin 6, or the device substrate, Pin 1. Under these conditions, input series resistor R3 is required. The peak input current should be limited to 20 mA. Excessively large values for R3 will degrade the current sensing accuracy. Figure 22 shows a method of bounding the voltage drop across RS without sacrificing current sensing accuracy.
Load
R3
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2
3
4
Comp Source Return Load
The above figure shows the MC33341 configured for source high-side current sensing allowing a common ground path between Load - and Source Return -. The Differential Amplifier inputs, Pins 1 and 6, are used to sense the load induced voltage drop that appears across resistor RS. The internal voltage and current regulation thresholds are selected by the respective external connections of Pins 2 and 6. Resistor R3 is required in applications where a high peak level of reverse current is possible if the source inputs are shorted. The resistor value should be chosen to limit the input current of the internal VCC clamp diode to less than 20 mA. Excessively large values for R3 will degrade the current sensing accuracy. V reg + V R2 ) 1 th(V) R1 V I reg + th(I HS) R S I R3 + R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
+ 0.2 R S
Figure 14. Source High-Side Current Sensing with Internally Fixed Voltage and Current Thresholds
http://onsemi.com
7
MC33341
Source RS Load
R3
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2
3
4
Current Control Source Return
Comp Load
The above figure shows the MC33341 configured for source high-side current sensing with an externally adjustable current threshold. Operation of this circuit is similar to that of Figure 14. The current regulation threshold can be adjusted over a range of 0 V to 200 mV with respect to Pin 4. V reg + V R2 ) 1 th(V) R1 V I reg + th(Pin 2) R S I R3 + R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
Figure 15. Source High-Side Current Sensing with Externally Adjustable Current and Internally Fixed Voltage Thresholds
http://onsemi.com
8
MC33341
Source Load
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2
3
4
R3 Source Return RS
Comp Load
The above figure shows the MC33341 configured for source return low-side current sensing allowing a common power path between Source + and Load +. This configuration is especially suited for negative output applications where a common ground path, Source + to Load +, is desired. The Inverting Amplifier inputs, Pins 1 and 4, are used to sense the load induced voltage drop that appears across resistor RS. The internal voltage and current regulation thresholds are selected by the respective external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of inrush current are possible. The resistor value should be chosen to limit the negative substrate current to less than 20 mA. Excessively large values for R3 will degrade the current sensing accuracy.
V reg + V
R2 ) 1 th(V) R1
V I reg +
th(I LS-) R S
I R3 +
R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
+ -0.2 R S
Figure 16. Source Return Low-Side Current Sensing with Internally Fixed Current and Voltage Thresholds
http://onsemi.com
9
MC33341
Source Load
Voltage Control
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 Current Control R3 Source Return RS 2
3
4
Comp Load
The above figure shows the MC33341 configured for source return low-side current sensing with externally adjustable voltage and current thresholds. Operation of this circuit is similar to that of Figure 16. The respective voltage and current regulation threshold can be adjusted over a range of 0 to 1.6 V and 0 V to 200 mV with respect to Pin 4. V reg + V R2 ) 1 th(Pin 6) R1 V I reg + - th(Pin 2) R S I R3 + R - 0.6 pk S 0.02
Figure 17. Source Return Low-Side Current Sensing with Externally Adjustable Current and Voltage Thresholds
http://onsemi.com
10
MC33341
Source Load
R3
R2
RS
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2
3
4
Comp Source Return Load
The above figure shows the MC33341 configured for load high-side current sensing allowing common paths for both power and ground, between the source and load. The Differential Amplifier inputs, Pins 1 and 6, are used to sense the load induced voltage drop that appears across resistor RS. The internal voltage and current regulation thresholds are selected by the respective external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of load current are possible from the battery or load bypass capacitor. The resistor value should be chosen to limit the input current of the internal VCC clamp diode to less than 20 mA. Excessively large values for R3 ill degrade the current sensing accuracy. V reg + V R2 ) 1 th(V) R1 V I reg + th(I HS) R S
I R3 +
R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
+ 0.2 R S
Figure 18. Load High-Side Current Sensing with Internally Fixed Current and Voltage Thresholds
http://onsemi.com
11
MC33341
Source Load
R2 R3
RS
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2
3
4
Current Control Source Return
Comp Load
The above figure shows the MC33341 configured for load high-side current sensing with an externally adjustable current threshold. Operation of this circuit is similar to that of Figure 18. The current regulation threshold can be adjusted over a range of 0 V to 200 mV with respect to Pin 4. V reg + V R2 ) 1 th(V) R1 V I reg + th(Pin 2) R S I R3 + R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
Figure 19. Load High-Side Current Sensing with Externally Adjustable Current and Internally Fixed Voltage Thresholds
http://onsemi.com
12
MC33341
Source Load
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2 R3
3
4
Comp Source Return
RS Load
The above figure shows the MC33341 configured for load low-side current sensing allowing common paths for both power and ground, between the source and load. The Noninverting input paths, Pins 1 and 4, are used to sense the load induced voltage drop that appears across resistor RS. The internal voltage and current regulation thresholds are selected by the respective external connections of Pins 2 and 6. Resistor R3 is required in applications where high peak levels of load current are possible from the battery or load bypass capacitor. The resistor value should be chosen to limit the negative substratecurrent to less than 20 mA. Excessively large values for R3 will degrade the current sensing accuracy. V reg + V R2 ) 1 th(V) R1 V I reg + th(I LS)) R S I R3 + R - 0.6 pk S 0.02
+ 1.2 R2 ) 1 R1
+ 0.2 R S
Figure 20. Load Low-Side Current Sensing with Internally Fixed Current and Voltage Thresholds
http://onsemi.com
13
MC33341
Source Load
Voltage Current
R2
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
R1
Opto Isolator R R
VCC Differential Amp R R R R VCC VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
Reference 0.2 V 0.4 V 1.2 V VCC 0.2 V
Battery or Resistive Load
Inverting Amp 1 2 R3 Current Control Source Return
3
4
Comp
RS
Load
The above figure shows the MC33341 configured for load low-side current sensing with an externally adjustable voltage and current threshold. Operation of this circuit is similar to that of Figure 20. The respective voltage and current regulation threshold can be adjusted over a range of 0 to 1.2 V and 0 V to 200 mV, with respect to Pin 4. V reg + V R2 ) 1 th(Pin 6) R1 V I reg + th(Pin 2) R S I R3 + R - 0.6 pk S 0.02
Figure 21. Load Low-Side Current Sensing with Externally Adjustable Current and Voltage Thresholds
http://onsemi.com
14
MC33341
Source RS
Load
8 Input Short 1
7
6
5 Output Short 4
MC33341 2 3
Source Return
Load
NOTE: An excessive load induced voltage across RS can occur if either the source input or load output is shorted. This voltage can easily be bounded with the addition of the diodes shown without degrading the current sensing accuracy. This bounding technique can be used in any of the MC33341 applications where high peak currents are anticipated.
Figure 22. Current Sense Resistor Bounding
Source
Load
Output 2
8
7
6
5
MC33341 1 2 3 4
Source
Load
Output 1
Opto Isolator
8
7
6
5
MC33341 1 2 3 4
Source Return
Load
Output Common
NOTE: Multiple outputs can be controlled by summing the error signal into a common optoisolator. The converter output with the largest voltage or current error will dominate control of the feedback loop.
Figure 23. Multiple Output Current and Voltage Regulation
http://onsemi.com
15
MC33341
Input 12 V to 16 V 0.2 MTP2955 Output 10 V/1.0 A 82.5 k
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
11.1 k
10 Differential Amp R R R R R R VCC
VCC
Vsen Vth Isen Ith I V
Transconductance Amp
10
VCC
VCC VCC
Reference 0.2 V 0.4 V 1.2 V 0.2 V
Variable Resistive Load
Inverting Amp 1 2
3 0.01
4
3.0 k Input Ground Output Ground
Figure 24. 10 V/1.0 A Constant-Voltage Constant-Current Regulator
10 8.0 6.0 4.0 2.0 0 0
V O, OUTPUT VOLTAGE (V)
0.2
04
0.6
0.8
1.0
IO, OUTPUT LOAD CURRENT (A) Figure 24 shows the MC33341 configured as a source high-side constant-voltage constant-current regulator. The regulator is designed for an output voltage of 10 V at 1.0 A. Figure 25 shows the regulator's output characteristics as the load is varied. Source return low-side, load high-side, and load low-side configurations will each exhibit a nearly identical load regulation characteristic. A heatsink is required for the MTP2955 series pass element.
Figure 25. Output Load Regulation
http://onsemi.com
16
MC33341
200 mH Input 12 V MTP2955 1N5821 100 68 k 0.25 Output 5.87 V/800 mA
3.0 k
8
7 VCC
6 VCC VCC 1.2 V
5
VCC 1.2 V Differential Amp Disable Logic 0.4 V
100 Differential Amp R R R R R R VCC
VCC
Vsen Vth Isen Ith I V
Transconductance Amp
VCC
VCC VCC
Reference 0.2 V 0.4 V 1.2 V 0.2 V
Inverting Amp 1 2
3
4
12 k
Input Ground
Output Ground
Figure 26 shows that the MC33341 can be configured as a high-side constant-current constant-voltage switch mode charger. This circuit operates as a step down converter. With a nominal input voltage and output load current as stated above, the switching frequency is approximately 28 kHz with and an associated conversion efficiency of 86 percent. The switching frequency will vary with changes in input voltage and load current.
Figure 26. Constant-Current Constant-Voltage Switch Mode Charger
ORDERING INFORMATION
Device MC33341D MC33341DG MC33341DR2 MC33341DR2G MC33341P MC33341PG TA = -25 to +85C Operating Temperature Range Package SOIC-8 SOIC-8 (Pb-Free) SOIC-8 SOIC-8 (Pb-Free) PDIP-8 PDIP-8 (Pb-Free) Shipping 98 Units / Rail 98 Units / Rail 2500 / Tape & Reel 2500 / Tape & Reel 50 Units / Rail 50 Units / Rail
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
17
MC33341
PACKAGE DIMENSIONS
SOIC-8 NB D SUFFIX PLASTIC PACKAGE CASE 751-07 ISSUE AH
-X- A
8 5
B
1 4
S
0.25 (0.010)
M
Y
M
-Y- G C -Z- H D 0.25 (0.010)
M SEATING PLANE
K
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751-01 THRU 751-06 ARE OBSOLETE. NEW STANDARD IS 751-07. MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244
N
X 45 _
0.10 (0.004)
M
J
ZY
S
X
S
DIM A B C D G H J K M N S
SOLDERING FOOTPRINT*
1.52 0.060
7.0 0.275
4.0 0.155
0.6 0.024
1.270 0.050
SCALE 6:1 mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
18
MC33341
PACKAGE DIMENSIONS
PDIP-8 P SUFFIX PLASTIC PACKAGE CASE 626-05 ISSUE L
NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040
8
5
-B-
1 4
F
NOTE 2
-A- L
C -T-
SEATING PLANE
J N D K
M
M TA B
H
G 0.13 (0.005)
M M
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative
http://onsemi.com
19
MC33341/D


▲Up To Search▲   

 
Price & Availability of MC3334106

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X