 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Current Limited Load Switch General Description The AAT4610A SmartSwitchTM is a member of AnalogicTechTM's Application Specific Power MOSFETTM (ASPMTM) product family. It is a Current Limited P-channel MOSFET power switch designed for high-side load-switching applications. This switch operates with inputs ranging from 2.4V to 5.5V, making it ideal for both 3V and 5V systems. An integrated current-limiting circuit protects the input supply against large currents which may cause the supply to fall out of regulation. The AAT4610A is also protected from thermal overload which limits power dissipation and junction temperatures. It can be used to control loads that require up to 1 A. Current limit threshold is programmed with a resistor from SET to ground. The quiescent supply current is typically a low 9A. In shutdown mode, the supply current decreases to less than 1A. The AAT4610A is available in a 5 pin SOT-23 or 8 pin SC70JW specified over -40 to 85C. The AAT4600 Series is a family of adjustable and fixed SmartSwitchTM with a range of current handling capabilities. Available are single versions in adj. current limit (AAT4600, AAT4601) as well as in fixed current limit (AAT4602, AAT4625). Dual versions (AAT4620, AAT4626) are also available. AAT4610A Features * * * * * * * * * * * * SmartSwitchTM 2.4V to 5.5V Input voltage range Programmable over current threshold Fast transient response: * 400ns response to short circuit Low quiescent current * 9A typical * 1A max with Switch off 145m typical RDS(ON) Only 2.5V needed for ON/OFF Control Undervoltage Lockout Thermal shutdown Temp range -40 to 85C 4kV ESD Rating UL Approved--File No. E217765 5 pin SOT-23 or 8-pin SC70JW package Preliminary Information Applications * * * * Peripheral ports Notebook computers Personal communication devices Hot swap supplies UL Recognized Component Typical Application INPUT 5 IN AAT4610A SOT-23 OUT 1 OUTPUT ON (ON) 4 ON/(ON) GND 2 SET 3 1F RSET 0.47F GND GND 4610A.2003.05.0.92 1 Current Limited Load Switch Pin Configuration 5-Pin SOT-23 (Top View) 8-Pin SC70JW (Top View) AAT4610A OUT GND SET 1 2 3 5 IN ON 4 SET ON IN IN 1 2 8 7 3 4 6 5 GND GND GND OUT 1 2 Pin Descriptions Pin # SOT23-5 SC70JW-8 Symbol OUT GND SET ON IN Function P-channel MOSFET drain. Connect 0.47F capacitor from OUT to GND. Ground connection Current-Limit Set Input. A resistor from SET to ground sets the current limit for the switch. Enable Input. Two versions are available, active-high and active-low. See ordering information for details. P-channel MOSFET source. Connect 1F capacitor from IN to GND. 1 2 3 4 5 5 6, 7, 8 1 2 3, 4 2 4610A.2003.05.0.92 Current Limited Load Switch Absolute Maximum Ratings Symbol VIN VON VSET, VOUT IMAX TJ TLEAD VESD AAT4610A (TA=25C unless otherwise noted) Value -0.3 to 6 -0.3 to VIN+0.3 -0.3 to VIN+0.3 2 -40 to 150 300 4000 Description IN to GND ON(ON) to GND SET, OUT to GND Maximum Continuous Switch Current Operating Junction Temperature Range Maximum Soldering Temperature (at Leads) ESD Rating1 - HBM Units V V V A C C V Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5k resistor into each pin. Thermal Characteristics Symbol JA PD Description Thermal Resistance (SOT23-5 or SC70JW-8) Power Dissipation2 (SOT23-5 or SC70JW-8) 2 Value 150 667 Units C/W mW Note 2: Mounted on a demo board. Electrical Characteristics are at TA=25C) Symbol VIN IQ IQ(OFF) ISD(OFF) VUVLO RDS(ON) TCRDS ILIM ILIM(MIN) VON(L) VON(H) ION(SINK) TRESP TOFF TON (VIN = 5V, TA = -40 to 85C unless otherwise noted. Typical values Description Operation Voltage Quiescent Current Off Supply Current Off Switch Current Undervoltage Lockout On-Resistance On-Resistance Temp-co Current Limit Minimum Current Limit ON (ON) Input Low Voltage ON (ON) Input High Voltage ON (ON) Input leakage Current Limit Response Time Turn-Off Time Turn-On Time Conditions VIN = 5V, ON (ON) = active, IOUT = 0 ON (ON) =inactive, VIN = 5.5V ON (ON) = inactive, VIN = 5.5V, VOUT = 0 Rising edge, 1% hysteresis, VIN=5.0V, TA=25C VIN=4.5V, TA=25C VIN=3.0V, TA=25C RSET = 6.8k VIN=2.7V to 5.5V 3 VIN=2.7V to <4.2V 3 VIN4.2V to 5.0V 3 VON = 5.5V VIN=5V VIN=5V, RL=10 VIN=5V, RL=10 Min 2.4 Typ 9 .01 1.8 145 150 190 2800 1 130 Max 5.5 25 1 1 2.4 180 230 1.25 0.8 Units V A A A V m m m ppm/C A mA V V V .75 2.0 2.4 0.01 0.4 4 12 1 12 200 A s s s Note 3: For VIN outside this range consult Typical ON (ON) Threshold curve.. 4610A.2003.05.0.92 3 Current Limited Load Switch Typical Characteristics (Unless otherwise noted, VIN = 5V, TA = 25C) Quiescent Current vs. Temperature 20 20 AAT4610A Quiescent Current vs. Input Voltage Quiescent Current (A) Quiescent Current (mA) 15 15 10 10 5 5 0 -40 0 0 1 2 3 4 5 6 -20 0 20 40 60 80 100 120 Temperature (C) IN (V) Output Current vs VOUT 0.6 RDS(ON) vs. Temperature 240 220 200 180 160 140 120 100 80 60 40 20 0 -40 Output Current ( A) Input = 3V 0.4 RDS(ON) (m) RSET =16 k 0.2 Input = 5V 0 0 1 2 3 4 5 -20 0 20 40 60 80 100 120 Vout ( V ) Temperature (C) Off-Supply Current vs. Temperature Off-Supply Current (A) Off-Switch Current (A) 10 10 Off-Switch Current vs. Temperature 1 1 0.1 0.1 0.01 0.01 -40 -20 0 20 40 60 80 100 120 0.001 -40 -20 0 20 40 60 80 100 120 Temperature (C) Temperature (C) 4 4610A.2003.05.0.92 Current Limited Load Switch (Unless otherwise noted, VIN = 5V, TA = 25C) Turn-On vs. Temperature RLOAD = 10, CLOAD = 0.47F 30 6 5 AAT4610A Turn-Off vs. Temperature RLOAD = 10, CLOAD = 0.47F VIN = 5V VIN = 3V Turn-On Time (S) 20 Turn-Off Time (S) 40 60 80 100 VIN = 3V 4 3 2 1 0 -40 -20 0 20 40 10 VIN = 5V 0 -40 -20 0 20 60 80 100 Temperature (C) Temperature (C) Turn-On RL = 10, CL = 0.47F 6 5 6 Turn-Off RL = 10, CL = 0.47F Voltage (V) 3 2 1 0 -1 -10 -5 0 5 10 15 20 25 30 35 40 45 50 Voltage (V) 4 ON Output 5 4 3 2 1 0 -1 -10 ON Output -5 0 5 10 15 20 25 30 35 40 45 50 Time (s) Time (s) Short Circuit through 0.3 8 12 10 2.20 2.00 V IH and V IL vs. VIN Input and Output (V) 7 6 5 4 3 2 1 0 -0.5 0.0 0.5 1.0 1.5 Input Voltage 8 6 Output (A) 1.80 1.60 1.40 1.20 1.00 0.80 Output Current Output Voltage 2.0 2.5 3.0 4 2 0 -2 -4 VIH VIL 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Time (s) VIN (V) 4610A.2003.05.0.92 5 Current Limited Load Switch (Unless otherwise noted, VIN = 5V, TA = 25C) RSET vs ILIM 100 10 AAT4610A RSET coefficent vs I LIM R SET I LIM Product ( kV ) 9 8 7 6 5 R SET (k ) 10 1 0.1 1 10 0 0.5 1 1.5 2 I LIM (A) I LIM (A) Current Limit v. Temperature 6% Current Limit (%) 4% 2% 0% -2% -4% -6% -50 RSET = 22.1k V IN -VOUT=0.5V - 25 0 25 50 75 100 Temperature (C) 6 4610A.2003.05.0.92 Current Limited Load Switch Functional Block Diagram AAT4610A IN OUT Undervoltage Lockout Over-Temp Protection ON (ON) 1.2V Reference Current Limit SET RSET GND 4610A.2003.05.0.92 7 Current Limited Load Switch Applications Information Setting Current Limit In most applications, the variation in ILIM must be taken into account when determining RSET. The ILIM variation is due to processing variations from part to part, as well as variations in the voltages at IN (pin 5) and OUT (pin 3), plus the operating temperature. See charts "Current Limit vs. Temperature", and "Output Current vs. VOUT". Together these three factors add up to a 25% tolerance (see ILIM specification in Electrical Characteristics section). In the figure below, a cold device with a statistically higher current limit, and a hot device with a statistically lower current limit, both with RSET equal to 10.5k are shown. While the chart, "RSET vs. ILIM" indicates an ILIM of 0.7A with an RSET of 10.5k, this figure shows that the actual current limit will be at least 0.525A, and no greater than 0.880A. Current Limit Using 10.5 k 1.2 AAT4610A that is less than or equal to it. For greater precision, the value of RSET may also be calculated using the ILIM RSET product found in the chart "RSET coefficient vs. ILIM". The maximum current is derived by multiplying the typical current for the chosen RSET in the chart by 1.25. A few standard resistor values are listed in the table "Current Limit RSET Values". Current Limit RSET Values RSET (k) 40.2 30.9 24.9 22.1 19.6 17.8 16.2 14.7 13.0 10.5 8.87 7.50 6.81 6.04 5.49 4.99 4.64 Current Limit typ (mA) 200 250 300 350 400 450 500 550 600 700 800 900 1000 1100 1200 1300 1400 Device will not current limit below: (mA) 150 188 225 263 300 338 375 413 450 525 600 675 750 825 900 975 1050 Device always current limits below: (mA) 250 313 375 438 500 563 625 688 750 875 1000 1125 1250 1375 1500 1625 1750 1 0.88 A Device with high current limit at -40 C 0.8 I LIM (A) 0.6 0.4 0.525 A Device with low current limit at 85 C 0.2 0 0 1 2 3 4 5 Vout (V ) To determine RSET, start with the maximum current drawn by the load, and multiply it by 1.33. (typical_ILIM = minimum_ILIM / 0.75) This is the typical current limit value. Next, refer to "RSET vs. ILIM" and find the RSET that corresponds to the typical current limit value. Choose the largest resistor available Example: A USB port requires 0.5A. 0.5A multiplied by 1.33 is 0.665A. From the chart named "RSET vs. ILIM", RSET should be less than 11k. 10.5 k is a standard value that is a little less than 11k but very close. The chart reads approximately 0.700A as a typical ILIM value for 10.5k. Multiplying 0.700A by 0.75 and 1.25 shows that the AAT4610 will limit the load current to greater than 0.525A but less than 0.875A. 8 4610A.2003.05.0.92 Current Limited Load Switch Overload Operation 1 0.75 0.5 AAT4610A Output ( V ) 0.25 0 5 4 3 2 1 0 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 Output Current 1 load is turned on at time = 0 Output Voltage Tim e ( s ) Operation in Current Limit When a heavy load is applied to the output of the AAT4610A, the load current is limited to the value of ILIM determined by RSET. See the figure "Overload Operation". Since the load is demanding more current than ILIM, the voltage at the output drops. This causes the AAT4610A to dissipate a larger than normal quantity of power, and its die temperature to increase. When the die temperature exceeds an over temperature limit, the AAT4610A will shut down until is has cooled sufficiently, at which point it will startup again. The AAT4610A will continue to cycle on and off until the load is removed, power is removed, or until a logic high level is applied to ON (pin 4). Enable Input In many systems, power planes are controlled by integrated circuits which run at lower voltages than the power plane itself. The enable input ON (pin 4) of the AAT4610A has low and high threshold voltages that accommodate this condition. The threshold voltages are compatible with 5 volt TTL, and 2.5 volt to 5 volt CMOS. Reverse Voltage The AAT4610A is designed to control current flowing from IN to OUT. If a voltage is applied to OUT which is greater than the voltage on IN, large currents may flow. This could cause damage to the AAT4610A. Output (A) 4610A.2003.05.0.92 9 Current Limited Load Switch Ordering Information Package SOT23-5 SOT23-5 SC70JW-8 SC70JW-8 Enable ON (active low) ON (active high) ON (active low) ON (active high) Marking1 ERXYY HXXYY FKXYY HXXYY Part Number (Tape and Reel) AAT4610AIGV-T1 AAT4610AIGV-1-T1 AAT4610AIJS-T1 AAT4610AIJS-1-T1 AAT4610A Note: Sample stock is generally held on all part numbers listed in BOLD. Note 1: XYY = assembly and date code. Package Information SOT23-5 2.85 0.15 1.90 BSC 0.95 BSC 1.575 0.125 1.10 0.20 0.60 REF 2.80 0.20 1.20 0.25 0.15 0.07 4 4 GAUGE PLANE 10 5 0.40 0.10 0.075 0.075 0.60 REF 0.45 0.15 0.10 BSC All dimensions in millimeters. 10 4610A.2003.05.0.92 Current Limited Load Switch SC70JW-8 0.50 BSC 0.50 BSC 0.50 BSC AAT4610A 1.75 0.10 0.225 0.075 2.00 0.20 2.20 0.20 0.048REF 0.15 0.05 0.85 0.15 1.10 MAX 0.100 7 3 0.45 0.10 2.10 0.30 4 4 All dimensions in millimeters. 0.05 0.05 4610A.2003.05.0.92 11 Current Limited Load Switch AAT4610A AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. AnalogicTech warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with AnalogicTech's standard warranty. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. Advanced Analogic Technologies, Inc. 830 E. Arques Avenue, Sunnyvale, CA 94085 Phone (408) 737-4600 Fax (408) 737-4611 12 4610A.2003.05.0.92 |
Price & Availability of AAT4610AIJS-T1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |