 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| (R) 74V1T07 SINGLE BUFFER (OPEN DRAIN) s s s s s s HIGH SPEED: tPD = 4.7 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 1 A (MAX.) at TA = 25 oC COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUT OPERATING VOLTAGE RANGE: VCC (OPR) = 4.5V to 5.5V IMPROVED LATCH-UP IMMUNITY S (SOT23-5L) C (SC-70) ORDER CODE: 74V1T07S 74V1T07C to 7V can be accepted on input with no regard to the supply voltage. This device can be used to interface 5V to 3V. DESCRIPTION The 74V1T07 is an advanced high-speed CMOS SINGLE BUFFER (OPEN DRAIN) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. It has similar high speed performance of equivalent Bipolar Schottky TTL combined with true CMOS low power dissipation. The internal circuit is composed of 2 stages including buffer output, which provide high noise immunity and stable output. Power down protection is provided on input and 0 PIN CONNECTION AND IEC LOGIC SYMBOLS September 1999 1/7 74V1T07 INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No 1 2 4 3 5 SYMBOL N.C. 1A 1Y GND VCC NAME AND FUNCT ION Not Connected Data Input Data Output Ground (0V) Positive Supply Voltage TRUTH TABLE A L H Z = High impedance Y L Z ABSOLUTE MAXIMUM RATINGS Symbol VCC VI VO IIK IOK IO Tstg TL Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Storage Temperature Lead Temperature (10 sec) Parameter Value -0.5 to +7.0 -0.5 to +7.0 -0.5 to VCC + 0.5 - 20 20 25 50 -65 to +150 260 Unit V V V mA mA mA mA o o ICC or IGND DC VCC or Ground Current C C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition is not implied. RECOMMENDED OPERATING CONDITIONS Symbol VCC VI VO Top dt/dv Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time (see note 3) (V CC = 5.0 0.5V) Parameter Valu e 4.5 to 5.5 0 to 5.5 0 to VCC -40 to +85 0 to 20 Unit V V V o C ns/V 1)VIN from0.8V to 2 V 2/7 74V1T07 DC SPECIFICATIONS Symb ol Parameter T est Cond ition s V CC (V) VIH VIL VOL IOZ II ICC ICC High Level Input Voltage Low Level Input Voltage Low Level Output Voltage 3 State Output Leakage Current Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current 4.5 to 5.5 4.5 to 5.5 4.5 4.5 5.5 0 to 5.5 5.5 5.5 VI = VI L IO=50 A IO=8 mA 0.0 Min. 2 0.8 0.1 0.36 0.25 0.1 1 1.35 Typ . Value T A = 25 o C Max. -40 to 85 o C Min . 2 0.8 0.1 0.44 2.5 1.0 10 1.5 Max. V V Un it V A A A mA VI = VIH or VIL VO = VCC or GND VI = 5.5V or GND VI = VCC or GND One Input at 3.4V, other input at VCC or GND AC ELECTRICAL CHARACTERISTICS (Input tr = tf =3 ns) Symb ol Parameter Test Co ndition V CC (*) (V) tPLZ tPZL Propagation Delay Time 5.0 5.0 CL (pF ) 15 50 o Value T A = 25 C Min. Typ . Max. 3.3 4.7 4.5 6.1 -40 to 85 C Min . Max. 1.0 1.0 5.4 7.1 o Un it ns (*) Voltage range is 5V 0.5V CAPACITIVE CHARACTERISTICS Symb ol Parameter T est Cond ition s Min. C IN CPD Input Capacitance Power Dissipation Capacitance (note 1) Typ . 4 9 Value T A = 25 o C Max. 10 -40 to 85 o C Min . Max. 10 pF pF Un it 1) CPD isdefined as the value of the IC'sinternal equivalent capacitance which is calculated fromthe operating current consumption without load. (Referto Test Circuit).Average operating current can be obtained by the following equation. ICC(opr) = CPD * VCC * fIN + ICC 3/7 74V1T07 TEST CIRCUIT CL = 15/50 pF or equivalent (includes jig and probe capacitance) RL = R1 = 1K or equivalent RT = ZOUT of pulse generator (typically 50) WAVEFORM: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 4/7 74V1T07 SOT23-5L MECHANICAL DATA mm MIN. A A1 A2 b C D E E1 L e e1 0.90 0.00 0.90 0.35 0.09 2.80 2.60 1.50 0.35 0.95 1.9 TYP. MAX. 1.45 0.15 1.30 0.50 0.20 3.00 3.00 1.75 0.55 MIN. 35.4 0.0 35.4 13.7 3.5 110.2 102.3 59.0 13.7 37.4 74.8 mils TYP. MAX. 57.1 5.9 51.2 19.7 7.8 118.1 118.1 68.8 21.6 DIM. 5/7 74V1T07 SC-70 MECHANICAL DATA mm MIN. A A1 A2 b C D E E1 L e e1 0.80 0.00 0.80 0.15 0.10 1.80 1.80 1.15 0.10 0.65 1.3 TYP. MAX. 1.10 0.10 1.00 0.30 0.18 2.20 2.40 1.35 0.30 MIN. 31.5 0.0 31.5 5.9 3.9 70.9 70.9 45.3 3.9 25.6 51.2 mils TYP. MAX. 43.3 3.9 39.4 11.8 7.1 86.6 94.5 53.1 11.8 DIM. 6/7 74V1T07 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics (c) 1999 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. http://www.st.com . 7/7 |
Price & Availability of 6574
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |