View MAX1284EVSYSTEM_990027.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

19-1738; Rev 0; 6/00
MAX1284 Evaluation System
General Description
The MAX1284 evaluation system (EV system) is a complete data-acquisition system consisting of a MAX1284 evaluation kit (EV kit) and a Maxim 68HC16MODULEDIP microcontroller (C) module. The MAX1284 is a high-speed, 12-bit data acquisition system. Windows 95/98 (R) software provides a handy user interface to exercise the MAX1284's features. Order the complete EV system (MAX1284EVC16) for comprehensive evaluation of the MAX1284 using a PC. You can order the EV kit (MAX1284EVKIT) if the 68HC16MODULE-DIP module has already been purchased with a previous Maxim EV system, or for custom use in other C-based systems. o Proven PC Board Layout o Convenient On-Board Test Points o Data-Logging Software o Fully Assembled and Tested
Features
Evaluates: MAX1284
Ordering Information
PART MAX1284EVKIT MAX1284EVC16 TEMP. RANGE 0C to +70C 0C to +70C INTERFACE TYPE User supplied Windows software
EV System Component List
PART MAX1284EVKIT 68HC16MODULE-DIP QTY 1 1 DESCRIPTION MAX1284 EV kit 68HC16 C module
Note: The MAX1284 software is designed for use with the complete MAX1284EVC16 EV system (includes 68HC16MODULEDIP module together with MAX1284EVKIT). If the MAX1284 evaluation software will not be used, the MAX1284EVKIT board can be purchased by itself, without the C.
EV Kit Component List
DESIGNATION QTY C1 C2, C3 C4 C5 J1 JU1 JU2 R1 TP1 U1 None None None None 1 2 1 1 1 1 1 1 1 1 1 1 1 1 DESCRIPTION 0.01F ceramic capacitor 0.1F ceramic capacitors 4.7F tantalum capacitor 10F, 10V tantalum capacitor 2x20 right-angle socket 2-pin header 3-pin header 1k 5% resistor 6-pin header MAX1284BCSA MAX1284 EV kit PC board 3-1/2in software disk, MAX1284 EV kit MAX1284 EV kit data sheet MAX1284 data sheet FILE INSTALL.EXE MAX1284.EXE KIT1284.C16
EV Kit Component List
DESCRIPTION Installs the EV kit files on your computer Application program Software loaded into 68HC16 C
Recommended Equipment
Before you begin, you will need the following equipment: * Maxim MAX1284EVC16 (contains MAX1284EVKIT board and 68HC16MODULE-DIP) * A small DC power supply, such as a 12VDC 0.25A plug-in transformer or a 9V battery * An IBM PC-compatible computer running Windows 95/98 * A spare serial communications port, preferably a 9-pin plug * A serial cable to connect the computer's serial port to the 68HC16MODULE-DIP
Windows 95/98 is a registered trademark of Microsoft Corp. ________________________________________________________________ Maxim Integrated Products 1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.
MAX1284 Evaluation System Evaluates: MAX1284
Quick Start
1) Carefully connect the boards by aligning the 40-pin header of the MAX1284 EV kit with the 40-pin connector of the 68HC16MODULE-DIP module, both boards component-side up. Gently press them together. The two boards should be flush against one another. 2) Ensure that JU1 is open and JU2 is in the 1-2 position. 3) Connect a +7VDC to +20VDC power source to the C module at the terminal block located next to the on/off switch, along the top edge of the C module. Observe the polarity marked on the board. 4) Connect a cable from the computer's serial port to the C module. If using a 9-pin serial port, use a straight-through, 9-pin female-to-male cable. If the only available serial port uses a 25-pin connector, a standard 25-pin-to-9-pin adapter will be required. The EV kit software checks the modem status lines (CTS, DSR, DCD) to confirm that the correct port has been selected. 5) Install the MAX1284 EV kit software on your computer by running the INSTALL.EXE program on the floppy disk. The program files are copied and icons are created for them in the Windows Start menu. 6) Start the MAX1284 program by opening its icon in the Start menu. 7) The program will prompt you to connect the C module and turn its power on. Slide SW1 to the ON position. Select the correct serial port and press OK. The program will automatically download KIT1284.C16 to the module. 8) Apply an input signal between AIN and GND. Observe the readout on the screen.
Software Description
The evaluation software's main window controls the serial-clock speed and sample rate. It displays the voltage and output code as well as some statistics of the input signal. A separate graph window shows the data changing in real time. The update rate is limited to about 10 samples per second, due to COM port bandwidth limitations.
Statistics
The Minimum and Maximum fields show the highest and lowest readings acquired. The Average field shows a running mean based on the equation ai = (k)(xi) + (1 - k)(ai - 1). The Clear button resets the statistics. To remove offset errors, first apply 0V to the active input channel, clear statistics, acquire some samples, and then check Tare. This average offset voltage will now be subtracted from all subsequent measurements.
Sampling
Choose the desired sampling rate (QSPITM Clock), sampling size (Sample! menu item), and press Begin Sampling! (in Sample! pop-up window). Sample size is restricted to a power of 2 to permit FFT processing once the data is saved to a file. After the samples have been collected, the data is automatically uploaded to the host and graphed. Once displayed, the data can be saved optionally to a file.
Saving Graphs to Disk
Data in the real-time graph and in sampled data graphs may be saved to a file. Only the raw output codes are saved, but voltages may be inferred, based on the reference voltage and the maximum code value.
Evaluating Shutdown
The evaluation software configures the 68HC16's QSPI submodule to continuously read data from the MAX1284 into the 68HC16. The sample rate is controlled by the QSPI clock. To evaluate power-saving modes, these automatic updates must be stopped. First, set the QSPI clock control to STOP. This reconfigures the 68HC16's QSPI submodule to stop driving the serial clock. Second, in the evaluation software's main window, uncheck the "Read Every...msec" checkbox. If evaluating the hardware shutdown, move jumper JU2 to the 2-3 position.
Detailed Description
MAX1284 Stand-Alone EV Kit
The MAX1284EVKIT provides a proven PC board layout to evaluate the MAX1284. It must be interfaced to appropriate timing signals for proper operation. Connect +5V to VDD, and connect the ground return to GND (Figure 1). Refer to the MAX1284 data sheet for timing requirements.
MAX1284 EV System
The MAX1284EVC16 EV system operates from a usersupplied +7VDC to +20VDC power supply. Windows 95/98 software running on an IBM PC interfaces to the EV system board through the computer's serial communications port. See the Quick Start section for setup and operating instructions.
2
Reference Voltage
The evaluation software assumes a 2.5V reference voltage, unless otherwise specified. Refer to the MAX1284 data sheet for more information. To override this value, type the new reference voltage into the Vref edit box and press the Set Vref button.
QSPI is a trademark of Motorola, Inc.
_______________________________________________________________________________________
MAX1284 Evaluation System Evaluates: MAX1284
GND J1-1 J1-2 J1-3 J1-4 VDD VDD C2 0.1F JU1 SHDN 3 6 J1-33 J1-34 J1-35 J1-37 J1-38 CS DOUT DOUT SCLK CS C3 0.1F C4 4.7F VREF (2.5V NOMINAL) 8 7 SHDN DOUT SCLK CS VDD 1 2 4 5 C1 0.01F R1 1k AIN 3 JU2 2 1 GND C5 10F
J1-7 J1-8 J1-28 J1-30
SCLK UPSHDN
U1 MAX1284
AIN REF GND
TP1-1 TP1-2 TP1-3 TP1-4 TP1-5 TP1-6
GND VDD SCLK CS DOUT SHDN J1-25 J1-26 J1-27 J1-29 J1-31 J1-32 J1-36 J1-19 J1-20 J1-21 J1-22 J1-23 J1-24 J1-40 J1-13 J1-14 J1-15 J1-16 J1-17 J1-18 J1-39 J1-5 J1-6 J1-9 J1-10 J1-11 J1-12
Figure 1. MAX1284 EV Kit Schematic Diagram
Detailed Hardware Description
The MAX1284, U1, is a high-speed, 12-bit data-acquisition system. Resistor R1 (1k) and capacitor C1 (0.01F) form a single-pole, low-pass anti-aliasing filter with a nominal 10s time constant and a corner frequency of approximately 16kHz. C3 and C4 bypass the analog-to-digital converter's (ADC's) voltage reference. When plugged into the 68HC16MODULE, the VDD circuit is powered by +5V (Figure 1; refer to the MAX1284 data sheet).
Problem: Measurements are erratic, unstable; poor accuracy. Check the reference voltage using a DVM. Use an oscilloscope to check for noise. When probing for noise, keep the oscilloscope ground return lead as short as possible, preferably less than 1/2in (10mm).
Table 1. Jumper JU1 Functions
JUMPER POSITION Closed JU1 Open* 1-2* JU2 2-3 Shutdown FUNCTION SHDN driven by C; JU2 must be open SHDN set by JU2 Operate
Troubleshooting
Problem: No output measurement. System seems to report zero voltage or fails to make a measurement. Check the VDD supply voltage. Check the reference voltage using a DVM. Use an oscilloscope to verify that the conversion-start signal is being strobed. Verify that SHDN is being driven high.
*Default configuration
_______________________________________________________________________________________
3
MAX1284 Evaluation System Evaluates: MAX1284
1.0"
Figure 2. MAX1284 EV Kit Component Placement Guide-- Component Side
1.0"
1.0"
Figure 3. MAX1284 EV Kit PC Board Layout--Component Side
Figure 4. MAX1284 EV Kit PC Board Layout--Solder Side
4
_______________________________________________________________________________________
19-1322; Rev 0; 12/97
68HC16 Module
_____________________________________________68HC16 Module Component List
DESIGNATION C1, C2, C3 C4, C5 C6, C7 C8 C9 C10-C14 D1 J1 J2 J3 J4 JU1 JU2 JU3 JU4 JU5 L1 L2 LED1 R1 QTY 3 2 2 1 0 5 1 1 1 1 0 0 0 0 0 0 0 0 1 1 DESCRIPTION 1F ceramic capacitors 22F, 25V radial-lead electrolytic capacitors 22pF capacitors 0.01F capacitor Reference designator, not used 0.1F capacitors 1N4001 diode 40-pin right-angle male connector 2-circuit terminal block Right-angle printed circuit board mount, DB9 female socket Open Open Reference designator, not used Open Open Open Open Open Light-emitting diode 10M, 5% resistor DESIGNATION R2 R3, R4 R5 R6 SW1 SW2 U1 U2 U3 U4 U5 U6 U7 Y1 None None None None None QTY 1 2 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 1 DESCRIPTION 330k, 5% resistor 10k, 5% resistors 470, 5% resistor 10k SIP resistor Slide switch Momentary pushbutton switch 68HC16 C MC68HC16Z1CFC16 (132-pin plastic quad flat pack) Maxim MAX233CPP 27C256 EPROM containing monitor program 7805 regulator, TO-220 size 62256 (32K x 8) static RAM 74HCT245 bidirectional buffer Maxim MAX707CPA 32.768kHz watch crystal Rubber feet 28-pin socket for U3 20-pin socket for U6 3" x 5" printed circuit board Heatsink for U4, thermalloy # 6078
68HC16 Module
68HC16 Module ________________General Description
The 68HC16 module is an assembled and tested printed-circuit board intended for use with Maxim's highspeed serial-interface evaluation kits (EV kits). The module uses an inexpensive 8-bit implementation of Motorola's MC68HC16Z1 microcontroller (C) to collect data samples at high speed using the QSPITM interface. It requires an IBM-compatible personal computer and an external DC power supply, typically 12V DC or as specified in EV kit manual. Maxim's 68HC16 module is provided to allow customers to evaluate selected Maxim products. It is not intended to be used as a microprocessor development platform, and such use is not supported by Maxim.
68HC16 Module ________________Detailed Description
Power Input Connector J2
The 68HC16 module draws its power from a user-supplied power source connected to terminal block J2. Be sure to note the positive and negative markings on the board. A three-terminal 5V regulator allows input voltages between 8V and an absolute maximum of 20V. The 68HC16 module typically requires 200mA of input current.
68HC16 Microcontroller
U1 is Motorola's 68HC16Z1 C. Contact Motorola for C information, development, and support. Maxim EV kits use the high-speed queued serial peripheral interface (QSPI) and the internal chip-select generation. A MAX707 on the module monitors the 5V logic supply, generates the power-on reset, and produces a reset pulse whenever the reset button is pressed.
QSPI is a trademark of Motorola Corp.
________________________________________________________________ Maxim Integrated Products
1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800. For small orders, phone 1-800-835-8769.
68HC16 Module 68HC16 Module
The 68HC16 uses a phase-locked loop (PLL) to set its bus speed. Crystal Y1 is a 32.768kHz frequency reference. The internal oscillator runs 256 times faster than the external crystal. When the 68HC16 is reset, it waits for the PLL to lock before it executes any software. After the PLL locks onto the reference frequency, the software doubles the clock speed by writing to the clock synthesizer control register, selecting a bus speed of 16.78MHz. U5, the user RAM area, is a 32kbyte CMOS static RAM. The 74HCT245 octal buffer lets the 68HC16 module access an 8-bit port on the 40-pin interface connector. This memory-mapped port consists of separate read and write strobes, four chip selects, four address LSBs, and eight data bits.
Table 1. Serial Communications Port J3
PIN 1 2 3 4 5 6 7 8 9 NAME DCD RXD TXD DTR GND DSR RTS CTS None FUNCTION Handshake; hard-wired to DTR and DSR RS-232-compatible data output from 68HC16 module RS-232-compatible data input to 68HC16 module Handshake; hard-wired to DCD and DSR Signal ground connection Handshake; hard-wired to DCD and DTR Handshake; hard-wired to CTS Handshake; hard-wired to RTS Unused
Serial Communications
J3 is an RS-232 serial port, designed to be compatible with the IBM PC 9-pin serial port. Use a straightthrough DB9 male-to-female cable to connect J3 to this port. If the only available serial port has a 25-pin connector, you may use a standard 25-pin to 9-pin adapter. Table 1 shows the pinout of J3. The MAX233 is an RS-232 interface voltage level shifter with two transmitters and two receivers. It includes a built-in charge pump with internal capacitors that generates the output voltages necessary to drive RS-232 lines.
Table 2. 40-Pin Data-Connector Signals
PIN 1-4 5, 6 7, 8 9 10 11 12 13 14 15 16 17 18 19 20-26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 NAME GND VPREREG VCC RD WR 7E000 7E800 7F000 7F800 A00 A01 A02 A03 EXTD0 EXTD1-7 IC1 IC2 IC3 OC1 OC2 OC3 OC4 IC4 MISO MOSI SCK PCS0/SS CLKOUT PWMA FUNCTION Ground Unregulated input voltage +5V from on-board regulator Read strobe Write strobe Chip select for 7E000-7E7FF Chip select for 7E800-7EFFF Chip select for 7F000-7F7FF Chip select for 7F800-7FFFF Address bit 0 (LSB) Address bit 1 Address bit 2 Address bit 3 Buffered data bus 0 (LSB) Buffered data bus bits 1-7 General I/O port bit 0 (LSB) General I/O port bit 1 General I/O port bit 2 General I/O port bit 3 General I/O port bit 4 General I/O port bit 5 General I/O port bit 6 General I/O port bit 7 QSPI master-in, slave-out QSPI master-out, slave-in QSPI serial clock QSPI chip-select output System clock output Pulse-width-modulator output
40-Pin Data Connector J1
The 20 x 2 pin header connects the 68HC16 module to a Maxim EV kit. Table 2 lists the function of each pin. Note that 68HC16 object code is not compatible with 68HC11 object code. Use the 68HC16 module only with those modules that are designed to support it, and only download code that is targeted for the 68HC16 module. Downloading incorrect object code into the 68HC16 module will have unpredictable results.
Address Ranges
The 68HC16 C generates various enable signals for different address ranges. The ROM and RAM enable signals are fed directly to the respective chips. Several additional signals (J1.11-J1.14) are available on the data connector to be used by Maxim EV kits. Table 3 outlines the address ranges for each of the elements found on the 68HC16 module, and Table 4 is a truth table that describes the logic for each of the 68HC16's chip-select outputs. Because the addresses are not completely decoded, the boot ROM and user RAM have shadows.
2
_______________________________________________________________________________________
68HC16 Module
Table 3. 68HC16 Module Memory Map (all address values are in 20-bit hex)
PIN 00000-07FFF 08000-0FFFF 10000-17FFF 18000-1FFFF 20000-203FF 20400-7DFFF 7E000-7E7FF 7E800-7EFFF 7F000-7F7FF 7F800-7FFFF 80000-F7FFF F8000-FF6FF FF700-FF73F FF740-FF8FF FF900-FF93F FF940-FF9FF FFA00-FFA7F FFA80-FFAFF FFB00-FFB07 FFB08-FFBFF FFC00-FFDFF FFE00-FFFFF FUNCTION Boot ROM (U3, strobed by CSBOOT) Shadow of boot ROM User RAM (U5, strobed by CS0 and CS2) Shadow of user RAM Internal standby RAM; 1kbyte Unused External chip select (J1 pin 11) (CS7) External chip select (J1 pin 12) (CS8) External chip select (J1 pin 13) (CS9) External chip select (J1 pin 14) (CS10) Not accessed by the 68HC16 Unused 68HC16's built-in ADC (not used) Unused General-purpose timer module (GPT) Unused System integration module (SIM) Unused Internal standby RAM (SRAM) control registers Unused Queued serial module (QSM) Unused
Boot ROM
The boot ROM, U3, is configured as an 8-bit memory device. Resistor R4 pulls data bit 0 low during system reset, forcing the C to fetch instructions using only the upper eight data bits. The boot ROM checks the system and waits for commands from the host. Refer to the EV kit manual for specific start-up procedures.
68HC16 Module
Software
All software is supplied on a disk with the EV kit. Instructions for operating the software are included in the EV kit manual. Refer to the EV kit manual for more information.
68HC16 Module Self Check
To test the 68HC16 module's integrity, connect the power supply to the power terminals (J2). Do not connect anything to J1 or J3. Slide the power switch SW1 to the "ON" position. The LED will light up, and will flash within 5 seconds. If the LED flashes with a 50%-on/50%-off duty cycle, then it passed its self check. Note that this test does not exercise the RS-232 port or the EV kit 40-pin interface, but it does confirm that the power supply, microprocessor, ROM, and RAM passed the self test. If the LED flashes with a 10%-on/90%-off duty cycle, then it failed its self check. Most likely, the RAM chip (U5) is bad. If the LED remains on and does not flash, then the problem is either U3 (the EPROM), U1 (the microprocessor), U4 (the regulator), the MAX707 reset generator, or the power supply. Use a voltmeter to verify that the power supplies are good. Check the power-supply input and the +5V output from the regulator. Use an oscilloscope to see if the 32.768kHz reference oscillator is running.
_______________________________________________________________________________________
3
68HC16 Module 68HC16 Module
Table 4. 68HC16 Chip-Select Outputs Truth Table
ADDRESS RANGE 0xxxx read 1xxxx read 1xxxx write 7E0xx read 7E0xx write 7E8xx read 7E8xx write 7F0xx read 7F0xx write 7F8xx read 7F8xx write CSBOOT L H H H H H H H H H H CS0 H H L H H H H H H H H CS1 H H H L H L H L H L H CS2 H L H H H H H H H H H CS5 H H H H L H L H L H L CS6 H H H L L L L L L L L CS7 H H H L L H H H H H H CS8 H H H H H L L H H H H CS9 H H H H H H H L L H H CS10 H H H H H H H H H L L
VCC
R5 470
LED1 PWMB
GROUND UNREGULATED 7V TO 20V REGULATED +5V INTEL COMPATIBLE READ/WRITE STROBES CHIP SELECTS LOW ADDRESS BITS
VCC
C13 0.1F GND
CS6/IOBUFFER CS1/RDIO D08 D09 D10 D11 D12 D13 D14 D15
19 OE 1 2 3 4 5 6 7 8 9
DIR A1 A2 A3 A4 A5 A6 A7 A8
U6 74HCT245
B1 B2 B3 B4 B5 B6 B7 B8
18 17 16 15 14 13 12 11
EXTD0 EXTD1 EXTD2 EXTD3 EXTD4 EXTD5 EXTD6 EXTD7
8-BIT BUFFERED BIDIRECTIONAL DATA BUS
8-BIT GENERAL I/O PORT
HIGH-SPEED SERIAL INTERFACE (QSM/QSPI) VCC
1 2 3 4
GND GND VPREREG VCC CS1/RDIO CS7/7E000 CS9/7F000 A00 A02 EXTD0 EXTD2 EXTD4 EXTD6 IC1 IC3 OC2 OC4 MISO SCK CLKOUT
J1-1 J1-3 J1-5 J1-7 J1-9 J1-11 J1-13 J1-15 J1-17 J1-19 J1-21 J1-23 J1-25 J1-27 J1-29 J1-31 J1-33 J1-35 J1-37 J1-39
J1-2 J1-4 J1-6 J1-8 J1-10 J1-12 J1-14 J1-16 J1-18 J1-20 J1-22 J1-24 J1-26 J1-28 J1-30 J1-32 J1-34 J1-36 J1-38 J1-40
GND GND VPREREG VCC CS5/WRIO CS8/7E800 CS10/7F800 A01 A03 EXTD1 EXTD3 EXTD5 EXTD7 IC2 OC1 OC3 IC4 MOSI PCSO/SS PWMA
TSTME BKPT/DSCLK BKPT/DSCLK HALT BERR MODCLK DSACK1 DSACK0 IRQ7 DS GND GND RESET VCC J4-1 J4-3 J4-5 J4-7 J4-9 J4-2 J4-4 J4-6 J4-8 J4-10 BERR BKPT/DSCLK FREEZE IPIPE1/DSI IPIPE0/DS0
R6 10k SIP RESISTOR
5 6 7 8 9 10
Figure 1. 68HC16 Module Schematic 4 _______________________________________________________________________________________
68HC16 Module 68HC16 Module
C14 0.1F C8 0.01F MISO MOSI SCK PCSO/SS PWMA PWMB VSSE VCC IC1 IC2 IC3 OC1 OC2 VSSI VDDI OC3 OC4 IC4 VCC CS10/7F800 CS9/7F000 CS8/7E800 CS7/7E000 CS6/IOBUFFER CS2/RDRAM CS1/RDIO VSSE
A01 A02 VCC VSSE A03 A04 A05 A06 A07 A08 VSSI A09 A10 A11 A12 A13 A14
VCC
VSSE
VRL ADA6 ADA7 VSTBY XTAL VDDSYN EXTAL VSSI VDDI XFC VDDE VSSE CLKOUT FREEZE/QUOT TSTME/TSC BKPT/DSCLK IPIPE0/DS0 IPIPE1/DS1 RESET HALT BERR IRQ7 IRQ6 IRQ5 IRQ4 IRQ3 IRQ2 IRQ1 MODCLK R/W SIZ1 SIZ0 VSSE
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
RXD PCS3 PCS2 PCS1 PCS0/SS SCK MOSI MISO VSSE VDDE IC1 IC2 IC3 OC1 OC2 VSSI VDDI OC3 OC4 IC4/OC5 PAI PWMA PWMB PCLK VSSE VDDE ADDR23 ADDR22 ADDR21 ADDR20 ADDR19 BGACK BG TXD ADDR1 ADDR2 VDDE VSSE ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 VSSI ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 VDDE VSSE VDDA VSSA ADA0 ADA1 ADA2 ADA3 ADA4 ADA5 VRH
116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117
RXD TXD
U1 MOTOROLA MC68HC16Z1CFC16
BR FC2 FC1 VDDE VSSE FCO CSBOOT DATA0 DATA1 DATA2 DATA3 VSSI DATA4 DATA5 DATA6 DATA7 DATA8 DATA9 VDDE VSSE DATA10 DATA11 DATA12 DATA13 DATA14 DATA15 ADDRO DSACK0 DSACK1 AVEC DS AS VDDE
CSO/WRRAM CS5/WRIO VCC VSSE CSBOOT/RDROM DOO
VSSI
DO8 DO9 VCC VSSE D10 D11 D12 D13 D14 D15 AOO DSACKO DSACK1 DS VCC
JU4 VSSE VCC
1 2
VCC VSSE CLKOUT FREEZE TSTME BKPT/DSCLK IPIPEO/DS0 IPIPE1/DSI RESET HALT BERR IRQ7
MODCLK
EXTAL VSSI VDDI
1
2 1
L2 10H OPTIONAL
C3 1F 2 20V VSSI
C10 0.1F
Figure 1. 68HC16 Module Schematic (continued) _______________________________________________________________________________________ 5
VSSE
XTAL
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83
VSTBY
68HC16 Module 68HC16 Module
R2 330k VCC
2 2
2
1 1 2
1
C7 22pF
XTAL R1 10M
7
J3-8 CTS J3-7 RTS T1OUT 5 T2OUT 18 R1IN 4 R2IN 19 C2+ 15 C2+ C216 C210 11
VCC TXD VCC GND
2 2
Y1 32.768kHz
1
T1IN T2IN R1OUT R2OUT C1+ C1-
2
1
C6 22pF
EXTAL
J3-2 RXD
1
VCC SW2 RESET
1 2 1
RXD
5
3
U7 MAX707
PFO 6 N.C. MR 8 RESET 4 7 RESET PFI GND
3
J3-3 TXD GND J3-4 DTR J3-6 DSR J3-1 DCD J3-5 GND
20 8 13
J2 + -
1 2
RESET
12
V17 V14
U2 MAX233
GND
9
V+
GND
6
SW1 POWER
1 2
D1 1N4001 VPREREG
2
JU5
1
GND L1 10H
VSSE
J3-9 RI
1 1
U4 78M05
IN OUT GND
2
3 1
VCC VCC C4 2 22F 25V
1 1 2
2 1 2
C1 OPTIONAL 1F 20V JU3
C2 1F 20V
VDDI
C5 2 22F 20V GND
VSSI
VSSE
1
2
D00
1
R4 10k
2
RESET A(00:18)
D09
1
R3 10k
2
RESET
A00 A01 A02 A03 A04 A05 A06 A07 A08 A09 A10 A11 A12 A13 A14
10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 20 22 27
A0 A1 U5 A2 62256 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 CS OE WE
VCC
A(00:18)
I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7
11 12 13 15 16 17 18 19
D08 D09 D10 D11 D12 D13 D14 D15
A00 A01 A02 A03 A04 A05 A06 A07 A08 A09 A10 A11 A12 A13
10 9 8 7 6 5 4 3 25 24 21 23 2 26 27 1 22 20
C12 0.1F GND
2
A0 A1 U3 A2 27C256 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 VPP OE CE
DQ0 DQ1 DQ2 DQ3 DQ4 DQ5 DQ6 DQ7
11 12 13 15 16 17 18 19
D08 D09 D10 D11 D12 D13 D14 D15
D(00:15)
VCC
C11 0.1F GND
GND CS2/RDRAM CS0/WRRAM
VCC CSBOOT/RDROM A14
1 3
VCC 32k x 8-BIT CMOS EPROM
32k x 8-BIT HIGH-SPEED CMOS STATIC RAM
Figure 1. 68HC16 Module Schematic (continued) 6 _______________________________________________________________________________________
D(00:15)
68HC16 Module 68HC16 Module
Figure 2. 68HC16 Module Component Placement Guide
_______________________________________________________________________________________
7
68HC16 Module 68HC16 Module
Figure 3. 68HC16 Module PC Board Layout--Component Side Figure 4. 68HC16 Module PC Board Layout--Solder Side
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2000 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.

▲Up To Search▲

Price & Availability of MAX1284EVSYSTEM

	To Download MAX1284EVSYSTEM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .