View NSC05228_994198.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MILITARY DATA SHEET MNCOPCG-XXX/V-MRP REV 0B0
Original Creation Date: 07/28/94 Last Update Date: 08/04/94 Last Major Revision Date: 07/28/94
SINGLE-CHIP microCMOS MICROCONTROLLER
General Description
The COP888 family of microcontrollers uses an 8-bit single chip core architecture fabricated with National Semiconductor's M2-CMOS(TM) process technology. The COP888CG is a member of this expandable 8-bit core processor family of microcontrollers. They are fully static parts, fabricated using double-metal silicon gate microCMOS technology. Features include an 8-bit memory mapped architecture, MICROWIRE/PLUS serial I/O, three 16-bit timer/counters supporting three modes (Processor Independent PWM generation, External Event counter, and Input Capture mode capabilities), full duplex UART, two comparators, and two power savings modes (HALT and IDLE), both with a multi-sourced wakeup/interrupt capability. This multi-sourced interrupt capability may also be used independent of the HALT or IDLE modes. Each I/O pin has software selectable configurations. The devices operate over a voltage range of 2.5V to 6V. High throughput is achieved with an efficient, regular instruction set operating at a maximum of 1uS per instruction rate.
Industry Part Number
COP888CG
NS Part Numbers
COPCG-XXX/V-MPC
Prime Die
COP8CG88
Processing
HERMETIC - MIL-STD-883, Method 5004 PLASTIC - SOP-5-264
Subgrp Description
1 2 3 4 5 6 7 8A 8B 9 10 11 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at
Temp ( oC)
+25 +85 -55 +25 +85 -55 +25 +85 -55 +25 +85 -55
Quality Conformance Inspection
HERMETIC - MIL-STD-883, Method 5005 PLASTIC - SOP-5-264
1
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
Features
Fully static CMOS, with low current drain Two power saving modes: HALT and IDLE 1uS instruction cycle time 4096 bytes on-board ROM (COP888CG) 192 bytes on-board RAM (COP888CG) Single supply operation: 2.5V-6V Full duplex UART Two analog comparators MICROWIRE/PLUS(TM) serial I/O WATCHDOG(TM) and Clock Monitor logic Idle Timer Multi-Input Wakeup (MIWU) with optional interrupts (8) Three 16-bit timers, each with two 16-bit registers supporting: - Processor Independent PWM mode - External Event counter mode - Input Capture mode 8-bit Stack Pointer SP (stack in RAM) Two 8-bit Register Indirect Data Memory Pointers (B and X) Fourteen multi-source vectored interrupts servicing - External Interrupt - Idle Timer T0 - Three Timers (Each with 2 Interrupts) - MIRCOWIRE/PLUS - Multi-Input Wake Up - Software Trap - UART (2) - Default VIS Versatile instruction set True bit manipulation Memory mapped I/O BCD arithmetic instructions Package: - 44 PLCC with 39 I/O pins Software selectable I/O options - TRI-STATE(R) Output - Push-Pull Output - Weak Pull Up Input - High Impedance Input Schmitt trigger inputs on ports G and L Temperature range: -55 C to +85 C Form factor emulation devices Real time emulation and full program debug offered by National's Development Systems
-
-
-
2
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
(Absolute Maximum Ratings)
(Note 1) Supply Voltage (Vcc) 7V Voltage at Any Pin -0.3V to Vcc + 0.3V Total Current into Vcc Pin (Source) 100mA Total Current out of GND Pin (Sink) 110mA Storage Temperature Range -65 C to +140 C Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings.
3
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
Electrical Characteristics
DC PARAMETERS
SYMBOL PARAMETER Operating Voltage Supply Current CKI = 10MHz, Vcc = 6.0V, tC = 1uS CKI = 4MHz, Vcc = 6.0V, tC = 2.5uS CKI = 4MHz, Vcc = 4.0V, tC = 2.5uS CKI = 1MHz, Vcc = 4.0V, tC = 10uS HALT Current CKI = 0MHz, Vcc = 6.0V CKI = 0MHz, Vcc = 4.0V Idle Current CKI = 10MHz, Vcc = 6.0V, tC = 1uS CKI = 4MHz, Vcc = 6.0V, tC = 2.5uS CKI = 1MHz, Vcc = 4.0V, tC = 10uS Vih Vil Vih Vil Input Levels RESET Input Levels RESET Input Levels CKI, All Other Inputs Input Levels CKI, All Other Inputs Hi-Z Input Leakage Input Pullup Current Output Current D Outputs Logic High Logic Low Logic High Logic Low Vcc = 6.0V, Vin = 0V Vcc = 6.0V, Vin = 0V Source, Vcc = 4.0V, Voh = 3.3V Source, Vcc = 2.5V, Voh = 1.8V Sink, Vcc = 4.0V, Vol = 1.0V Sink, Vcc = 2.5V, Vol = 0.4V -2 40 .4 .2 10 2 0.7Vcc 0.8Vcc 1 1 1 1 2 2 CONDITIONS NOTES PINNAME MIN 2.5 6 12.5 5.5 2.5 1.4 10 6 3.5 2.5 0.7 MAX UNIT V mA mA mA mA uA uA mA mA mA V 0.2Vcc V V 0.2Vcc V 2 250 uA uA mA mA mA mA SUBGROUPS 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3
4
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
Electrical Characteristics
DC PARAMETERS(Continued)
SYMBOL PARAMETER Output Current All Others CONDITIONS Source (Weak Pull-Up) Vcc=4.0V, Voh=2.7V Source (Weak Pull-Up) Vcc=2.5V, Voh=1.8V Source (Push-Pull Mode) Vcc = 4.0V, Voh = 3.3V Source (Push-Pull Mode) Vcc = 2.5V, Voh = 1.8V Sink (Push-Pull Mode) Vcc=4.0V, Vol=0.4V Sink (Push-Pull Mode) Vcc=2.5V, Vol=0.4V Tri-State Leakage Vr RAM Retention Voltage Vcc = 6V 500nS Rise and Fall Time (min) NOTES PINNAME MIN 10 2.5 .4 .2 1.6 .7 -2 2 2 MAX 110 33 UNIT uA uA mA mA mA mA uA V SUBGROUPS 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3
5
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
Electrical Characteristics
AC PARAMETERS
SYMBOL tC PARAMETER Instruction Cycle Time Crystal/Resonator CONDITIONS 4V <= Vcc =< 6V 2.5 = Vcc =< 4V tC Instruction Cycle Time R/C Oscillator Mode Output Propagation Delay 4V <= Vcc =< 6V 2.5 <= Vcc =< 4V SO, SK, RL = 2.2K, CL = 100pF, 4V <= Vcc =< 6V SO, SK, RL = 2.2K, CL = 100pF, 2.5V <= Vcc =< 4V All Others, RL = 2.2K, CL = 100pF, 4V <= Vcc =< 6V All Others, RL = 2.2K, CL = 100pF, 2.5V <= Vcc =< 4V Input Pulse Width Interrupt Input High Time Input Pulse Width Interrupt Input Low Time Input Pulse Width Timer Input High Time Input Pulse Width Timer Input Low Time RESET Pulse Width Input Offset Voltage Input Common Mode Voltage Range Low Level Output Current High Level Output Current Note 1: Note 2: Vol = 0.4V Voh = 4.6V .4V <= Vin =< Vcc -1.5V .4 1.6 1.6 3 3 3 3 4 1 NOTES PINNAME 1 2.5 3 7.5 MIN MAX DC DC DC DC .7 1.75 1 2.5 UNIT uS uS uS uS uS uS uS uS tC SUBGROUPS 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11 9, 10, 11
tPD1, tPD0
4
1
tC
4
1
tC
4
1
tC
1 +25 Vcc -1.5
uS mV V mA mA
Supply current measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open. The HALT mode will stop CKI from oscillating in the RC and the Crystal configurations. Measurement of IDD HALT is done with device neither sourcing or sinking current; with L, C, and G0-G5 programmed as low outputs and not driving a load; all inputs tied to Vcc; clock monitor and comparators disabled. Parameter refers to HALT mode entered via setting bit 7 of the G Port data register. Part will pull up CKI during HALT in crystal clock mode.
6
MNCOPCG-XXX/V-MRP REV 0B0
MILITARY DATA SHEET
(Continued)
Note 3: Note 4: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs. tC = Instruction Cycle Time.
7
MNCOPCG-XXX/V-MRP REV 0B0
Burn-in/QCI Electrical End-Point Tests
OP# 01 02 03 04 05 06 07 08 Operation description MRP, B4 - Must be performed within 48 hours of moisture MRP, C1 - Must be performed within 96 hours of burn-in MRP, C1 MRP, C2 - Must be performed within 48 hours of moisture MRP, D2 MRP, D3 MRP, D4 - Test between precondition and Temp. Cycle MRP, D4 1,9 1,9 2,3,10,11 1,9 1,9 1,2,9,10 1,9 1,2,9,10 Sub-Groups
Graphics and Diagrams
GRAPHICS# V44ARK DESCRIPTION PLASTIC CHIP CARRIER,SQ,.050LD PITCH,44LD(P/P DWG)
See attached graphics following this page.
8

▲Up To Search▲

Price & Availability of NSC05228

	To Download NSC05228 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .