View ON1724_996380.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Order this document by MC74VHC4051/D
Advance Information
Demultiplexers
Analog Multiplexers/
MC74VHC4051 MC74VHC4052 MC74VHC4053
High-Performance Silicon-Gate CMOS
The MC74VHC4051, MC74VHC4052 and MC74VHC4053 utilize silicon- gate CMOS technology to achieve fast propagation delays, low ON resistances, and low OFF leakage currents. These analog multiplexers/ demultiplexers control analog voltages that may vary across the complete power supply range (from VCC to VEE). The VHC4051, VHC4052 and VHC4053 are identical in pinout to the high-speed HC4051A, HC4052A and HC4053A, and the metal-gate MC14051B, MC14052B and MC14053B. The Channel-Select inputs determine which one of the Analog Inputs/Outputs is to be connected, by means of an analog switch, to the Common Output/Input. When the Enable pin is HIGH, all analog switches are turned off. The Channel-Select and Enable inputs are compatible with standard CMOS outputs; with pullup resistors they are compatible with LSTTL outputs. These devices have been designed so that the ON resistance (Ron) is more linear over input voltage than R on of metal-gate CMOS analog switches. For a multiplexer/demultiplexer with channel-select latches, see VHC4351. * Fast Switching and Propagation Speeds * Low Crosstalk Between Switches * Diode Protection on All Inputs/Outputs * Analog Power Supply Range (VCC - VEE) = 2.0 to 12.0 V * Digital (Control) Power Supply Range (VCC - GND) = 2.0 to 6.0 V * Improved Linearity and Lower ON Resistance Than Metal-Gate Counterparts * Low Noise * In Compliance With the Requirements of JEDEC Standard No. 7A * Chip Complexity: VHC4051 -- 184 FETs or 46 Equivalent Gates VHC4052 -- 168 FETs or 42 Equivalent Gates VHC4053 -- 156 FETs or 39 Equivalent Gates LOGIC DIAGRAM MC74VHC4051 Single-Pole, 8-Position Plus Common Off
X0 14 X1 15 X2 ANALOG 12 MULTIPLEXER/ INPUTS/ X3 DEMULTIPLEXER OUTPUTS X4 1 5 X5 2 X6 4 X7 11 A CHANNEL 10 B SELECT 9 INPUTS C 6 ENABLE PIN 16 = VCC PIN 7 = VEE PIN 8 = GND
13
D SUFFIX 16-LEAD SOIC PACKAGE CASE 751B-05
DT SUFFIX 16-LEAD TSSOP PACKAGE CASE 948F-01
ORDERING INFORMATION MC74VHCXXXXD MC74VHCXXXXDT SOIC TSSOP
FUNCTION TABLE - MC74VHC4051
Control Inputs Enable L L L L L L L L H C L L L L H H H H X Select B A L L H H L L H H X L H L H L H L H X ON Channels X0 X1 X2 X3 X4 X5 X6 X7 NONE X = Don't Care
3
X
COMMON OUTPUT/ INPUT
Pinout: MC74VHC4051 (Top View)
VCC 16 X2 15 X1 14 X0 13 X3 12 A 11 B 10 C 9
1 X4
2 X6
3 X
4 X7
5 X5
6
7
Enable VEE
8 GND
This document contains information on a new product. Specifications and information herein are subject to change without notice. 07/99
(c) Motorola, Inc. 1999
1
REV 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
FUNCTION TABLE - MC74VHC4052 LOGIC DIAGRAM MC74VHC4052 Double-Pole, 4-Position Plus Common Off
X0 14 X1 15 X2 11 X3 Y0 Y1 Y2 Y3 A B
1 5 2 4 10 9 6 12
Control Inputs Select Enable L L L L H X = Don't Care B L L H H X A L H L H X ON Channels Y0 Y1 Y2 Y3 NONE X0 X1 X2 X3
X SWITCH
13
X COMMON OUTPUTS/INPUTS
ANALOG INPUTS/OUTPUTS
Y SWITCH
3
Y
Pinout: MC74VHC4052 (Top View)
PIN 16 = VCC PIN 7 = VEE PIN 8 = GND VCC 16 X2 15 X1 14 X 13 X0 12 X3 11 A 10 B 9
CHANNEL-SELECT INPUTS
ENABLE
1 Y0
2 Y2
3 Y
4 Y3
5 Y1
6
7
Enable VEE
8 GND
FUNCTION TABLE - MC74VHC4053 LOGIC DIAGRAM MC74VHC4053 Triple Single-Pole, Double-Position Plus Common Off
X0 13 X1 Y0 1 Y1 Z0 3 Z1 A 10 CHANNEL-SELECT B INPUTS 9 C 6 ENABLE
11 5 2 12 14
Control Inputs Enable L L L L L L L L H C L L L L H H H H X Select B A L L H H L L H H X L H L H L H L H X ON Channels Z0 Z0 Z0 Z0 Z1 Z1 Z1 Z1 Y0 Y0 Y1 Y1 Y0 Y0 Y1 Y1 NONE X0 X1 X0 X1 X0 X1 X0 X1
X SWITCH
X
ANALOG INPUTS/OUTPUTS
Y SWITCH
15
Y
COMMON OUTPUTS/INPUTS
Z SWITCH
4
Z
X = Don't Care
PIN 16 = VCC PIN 7 = VEE PIN 8 = GND
Pinout: MC74VHC4053 (Top View)
VCC 16 Y 15 X 14 X1 13 X0 12 A 11 B 10 C 9
NOTE: This device allows independent control of each switch. Channel-Select Input A controls the X-Switch, Input B controls the Y-Switch and Input C controls the Z-Switch
1 Y1
2 Y0
3 Z1
4 Z
5 Z0
6
7
Enable VEE
8 GND
MOTOROLA
2
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
III I I I IIIIIIIIIIIIIIIIIIIIIII I I II I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I I I I I IIIIIIIIIIIIIIIIIIIIIII I I II I I I I I I IIIIIIIIIIIIIIIIIIIIIII I I III I I I I II I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIII II I I I I II I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII I I I I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII I I III I I I IIIIIIIIIIIIIIIIIIIIIII I IIIIIIII I I I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIII
MAXIMUM RATINGS*
Symbol VCC VEE VIS Vin I Parameter Value Unit V V V V Positive DC Supply Voltage (Referenced to GND) (Referenced to VEE) - 0.5 to + 7.0 - 0.5 to + 14.0 - 7.0 to + 5.0 VEE - 0.5 to VCC + 0.5 25 500 450 Negative DC Supply Voltage (Referenced to GND) Analog Input Voltage Digital Input Voltage (Referenced to GND) DC Current, Into or Out of Any Pin Power Dissipation in Still Air, Storage Temperature Range - 0.5 to VCC + 0.5 mA PD SOIC Package TSSOP Package mW Tstg TL - 65 to + 150 260
_C _C
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, Vin and Vout should be constrained to the range GND (Vin or Vout) VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or V CC ). Unused outputs must be left open.
v
v
Lead Temperature, 1 mm from Case for 10 Seconds
* Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Derating -- SOIC Package: - 7 mW/_C from 65_ to 125_C TSSOP Package: - 6.1 mW/_C from 65_ to 125_C
RECOMMENDED OPERATING CONDITIONS
III I I I I IIIIIIIIIIIIIIIIIIIII II IIII I IIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIII IIII I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII II I I III III I I IIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII III I IIIIIIIIIIIIIIIIIIIIIII III III I I II I IIIIIIIIIIIIIIIIIIIIIII III I I IIIIIIIIIIIIIIIIIIIIIII III II I IIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIII I I
Symbol VCC VEE VIS Vin Parameter Min 2.0 2.0 Max Unit V V V V V Positive DC Supply Voltage (Referenced to GND) (Referenced to VEE) 6.0 12.0 Negative DC Supply Voltage, Output (Referenced to GND) Analog Input Voltage - 6.0 VEE GND VCC VCC 1.2 Digital Input Voltage (Referenced to GND) Static or Dynamic Voltage Across Switch GND VIO* TA Operating Temperature Range, All Package Types Input Rise/Fall Time (Channel Select or Enable Inputs) - 55 0 0 0 0 + 125 1000 800 500 400
_C
ns
tr, tf
VCC = 2.0 V VCC = 3.0 V VCC = 4.5 V VCC = 6.0 V
* For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may be drawn; i.e., the current out of the switch may contain both VCC and switch input components. The reliability of the device will be unaffected unless the Maximum Ratings are exceeded.
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
3
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
DC CHARACTERISTICS -- Digital Section (Voltages Referenced to GND) VEE = GND, Except Where Noted
Symbol S bl VIH Parameter P Minimum High-Level Input Voltage, Channel-Select or Enable Inputs Condition C di i Ron = Per Spec VCC V 2.0 3.0 4.5 6.0 2.0 3.0 4.5 6.0 6.0 Guaranteed Limit -55 to 25C 1.50 2.10 3.15 4.20 0.5 0.9 1.35 1.8 0.1 85C 1.50 2.10 3.15 4.20 0.5 0.9 1.35 1.8 1.0 125C 1.50 2.10 3.15 4.20 0.5 0.9 1.35 1.8 1.0 Unit Ui V
VIL
Maximum Low-Level Input Voltage, Channel-Select or Enable Inputs
Ron = Per Spec
V
Iin ICC
Maximum Input Leakage Current, Channel-Select or Enable Inputs Maximum Quiescent Supply Current (per Package)
Vin = VCC or GND, VEE = - 6.0 V Channel Select, Enable and VIS = VCC or GND; VEE = GND VIO = 0 V VEE = - 6.0
A A
6.0 6.0
1 4
10 40
40 160
DC ELECTRICAL CHARACTERISTICS Analog Section
II I I III I I I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I III I I I III I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I I I III I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I III I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I III I I I I I I I I III I I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I I I III I I III I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I III I I I I I I I I III I I I III I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I III III I IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII I I I III I I
Guaranteed Limit S bl Symbol Ron P Parameter T Test C di i Conditions VCC V 3.0 4.5 4.5 6.0 3.0 4.5 4.5 6.0 3.0 4.5 4.5 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 VEE V - 55 to 25_C TBD 190 120 100 TBD 150 100 80 TBD 30 12 10 0.1 0.2 0.1 0.1 0.2 0.1 0.1
v 85_C v 125_C
TBD 240 150 125 TBD 190 125 100 TBD 35 15 12 0.5 2.0 1.0 1.0 2.0 1.0 1.0 TBD 280 170 140 TBD 230 140 115 TBD 40 18 14 1.0 4.0 2.0 2.0 4.0 2.0 2.0
Ui Unit
Maximum "ON" Resistance
Vin = VIL or VIH VIS = VCC to VEE IS 2.0 mA (Figures 1, 2)
v
0.0 0.0 - 4.5 - 6.0 0.0 0.0 - 4.5 - 6.0 0.0 0.0 - 4.5 - 6.0
Vin = VIL or VIH VIS = VCC or VEE (Endpoints) IS 2.0 mA (Figures 1, 2)
v
Ron
Maximum Difference in "ON" Resistance Between Any Two Channels in the Same Package
Vin = VIL or VIH VIS = 1/2 (VCC - VEE) IS 2.0 mA
v
Ioff
Maximum Off-Channel Leakage Current, Any One Channel
Vin = VIL or VIH; VIO = VCC - VEE; Switch Off (Figure 3) Vin = VIL or VIH; VIO = VCC - VEE; Switch Off (Figure 4)
A
- 6.0 - 6.0 - 6.0 - 6.0 - 6.0 - 6.0 - 6.0
Maximum Off-Channel VHC4051 Leakage Current, VHC4052 Common Channel VHC4053 Ion Maximum On-Channel VHC4051 Leakage Current, VHC4052 Channel-to-Channel VHC4053
Vin = VIL or VIH; Switch-to-Switch = VCC - VEE; (Figure 5)
A
MOTOROLA
4
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
AC CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)
Symbol S bl tPLH, tPHL Parameter P Maximum Propagation Delay, Channel-Select to Analog Output (Figure 9) VCC V 2.0 3.0 4.5 6.0 2.0 3.0 4.5 6.0 2.0 3.0 4.5 6.0 2.0 3.0 4.5 6.0 Guaranteed Limit -55 to 25C 370 TBD 74 63 60 TBD 12 10 290 TBD 58 49 345 TBD 69 59 10 35 130 80 50 1.0 85C 465 TBD 93 79 75 TBD 15 13 364 TBD 73 62 435 TBD 87 74 10 35 130 80 50 1.0 125C 550 TBD 110 94 90 TBD 18 15 430 TBD 86 73 515 TBD 103 87 10 35 130 80 50 1.0 Unit Ui ns
tPLH, tPHL
Maximum Propagation Delay, Analog Input to Analog Output (Figure 10)
ns
tPLZ, tPHZ
Maximum Propagation Delay, Enable to Analog Output (Figure 11)
ns
tPZL, tPZH
Maximum Propagation Delay, Enable to Analog Output (Figure 11)
ns
Cin CI/O
Maximum Input Capacitance, Channel-Select or Enable Inputs Maximum Capacitance (All Switches Off) Analog I/O Common O/I: VHC4051 VHC4052 VHC4053 Feedthrough
pF pF
Typical @ 25C, VCC = 5.0 V, VEE = 0 V CPD Power Dissipation C P Di i i Capacitance (Fi i (Figure 13)* VHC4051 VHC4052 VHC4053 45 80 45 pF F
* Used to determine the no-load dynamic power consumption: P D = C PD V CC 2 f + I CC V CC .
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
5
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
ADDITIONAL APPLICATION CHARACTERISTICS (GND = 0 V)
VCC V VEE V `51 2.25 2 25 4.50 6.00 2.25 4.50 6.00 2.25 4.50 6.00 2.25 4.50 6.00 2.25 4.50 6.00 2.25 4.50 6.00 2.25 4.50 6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 -2.25 -4.50 -6.00 80 80 80 Limit* 25C `52 95 95 95 -50 -50 -50 -40 -40 -40 25 105 135 35 145 190 -50 -50 -50 -60 -60 -60 % 2.25 4.50 6.00 -2.25 -4.50 -6.00 0.10 0.08 0.05 dB mVPP `53 120 120 120 dB Unit Ui MHz
Symbol S bl BW
Parameter P Maximum On-Channel Bandwidth or Minimum Frequency Response (Figure 6)
Condition C di i fin = 1MHz Sine Wave; Adjust fin Voltage to Obtain 0dBm at VOS; Increase fi Frequency in Until dB Meter Reads -3dB; RL = 50, CL = 10pF fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600, CL = 50pF
--
Off-Channel Feedthrough Isolation (Figure 7)
fin = 1.0MHz, RL = 50, CL = 10pF -- Feedthrough Noise. Channel-Select Input to Common I/O (Figure 8) Vin 1MHz Square Wave (tr = tf = 6ns); Adjust RL at Setup so that IS = 0A; Enable = GND RL = 600, CL = 50pF
RL = 10k, CL = 10pF -- Crosstalk Between Any Two Switches (Figure 12) (Test does not apply to VHC4051) fin = Sine Wave; Adjust fin Voltage to Obtain 0dBm at VIS fin = 10kHz, RL = 600, CL = 50pF
fin = 1.0MHz, RL = 50, CL = 10pF THD Total Harmonic Distortion (Figure 14) fin = 1kHz, RL = 10k, CL = 50pF THD = THDmeasured - THDsource VIS = 4.0VPP sine wave VIS = 8.0VPP sine wave VIS = 11.0VPP sine wave
* Limits not tested. Determined by design and verified by qualification.
Ron , ON RESISTANCE (OHMS)
200 125C 150
Ron , ON RESISTANCE (OHMS)
250
100 80 60
125C 25C
TBD
100
25C
TBD
40 20 - 55C
- 55C 50
0
0.25
0.50
0.75
1.0
1.25
1.5
1.75
2.0
2.25
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1a. Typical On Resistance, VCC - VEE = 2.0 V
Figure 1b. Typical On Resistance, VCC - VEE = 3.0 V
MOTOROLA
6
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
105 Ron , ON RESISTANCE (OHMS) Ron , ON RESISTANCE (OHMS) 90 75 60 45 30 15 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 125C 25C
75 60 45
125C 25C
TBD
- 55C
TBD
30 15
- 55C
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1c. Typical On Resistance, VCC - VEE = 4.5 V
Figure 1d. Typical On Resistance, VCC - VEE = 6.0 V
70 Ron , ON RESISTANCE (OHMS) 60 50 40 30 20 10 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 125C 25C Ron , ON RESISTANCE (OHMS)
70 60 50 40 30 20 10 0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 125C 25C
TBD
- 55C
TBD
- 55C
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
VIS, INPUT VOLTAGE (VOLTS), REFERENCED TO VEE
Figure 1e. Typical On Resistance, VCC - VEE = 9.0 V
Figure 1f. Typical On Resistance, VCC - VEE = 12.0 V
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
7
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
PLOTTER
PROGRAMMABLE POWER SUPPLY - +
MINI COMPUTER
DC ANALYZER
VCC DEVICE UNDER TEST
ANALOG IN
COMMON OUT
GND
VEE
Figure 2. On Resistance Test Set-Up
MOTOROLA
8
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
VCC VCC
VEE OFF VCC A NC OFF
16
VCC
VEE VCC
16 ANALOG I/O OFF OFF
VCC
COMMON O/I
COMMON O/I
VIH
6 7 8
VIH
6 7 8
VEE
VEE
Figure 3. Maximum Off Channel Leakage Current, Any One Channel, Test Set-Up
Figure 4. Maximum Off Channel Leakage Current, Common Channel, Test Set-Up
VCC A ON VEE VCC ANALOG I/O VIL 6 7 8 OFF
16
VCC fin COMMON O/I N/C
0.1F ON
VCC 16
VOS dB METER CL* RL
6 7 8 VEE *Includes all probe and jig capacitance
VEE
Figure 5. Maximum On Channel Leakage Current, Channel to Channel, Test Set-Up
Figure 6. Maximum On Channel Bandwidth, Test Set-Up
VIS 0.1F fin RL OFF
VCC 16
VOS dB METER CL* RL RL ON/OFF ANALOG I/O OFF/ON RL
VCC 16 COMMON O/I RL CL* TEST POINT
6 7 8 VEE VIL or VIH CHANNEL SELECT *Includes all probe and jig capacitance
Vin 1 MHz tr = tf = 6 ns VEE VCC GND
6 7 8
VCC 11
CHANNEL SELECT *Includes all probe and jig capacitance
Figure 7. Off Channel Feedthrough Isolation, Test Set-Up
Figure 8. Feedthrough Noise, Channel Select to Common Out, Test Set-Up
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
9
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
VCC VCC CHANNEL SELECT tPLH ANALOG OUT 50% GND tPHL 6 7 8 CHANNEL SELECT *Includes all probe and jig capacitance ON/OFF ANALOG I/O OFF/ON CL* VCC 16 COMMON O/I TEST POINT
50%
Figure 9a. Propagation Delays, Channel Select to Analog Out
Figure 9b. Propagation Delay, Test Set-Up Channel Select to Analog Out
VCC 16 VCC 50% GND tPLH ANALOG OUT 50% tPHL 6 7 8 ANALOG I/O ON CL* COMMON O/I TEST POINT
ANALOG IN
*Includes all probe and jig capacitance
Figure 10a. Propagation Delays, Analog In to Analog Out
Figure 10b. Propagation Delay, Test Set-Up Analog In to Analog Out
tf ENABLE tPZL ANALOG OUT 50%
tr 90% 50% 10% tPLZ VCC GND HIGH IMPEDANCE 10% tPZH tPHZ VOL VCC 1 2 1 2
POSITION 1 WHEN TESTING tPHZ AND tPZH POSITION 2 WHEN TESTING tPLZ AND tPZL VCC 16 ANALOG I/O ON/OFF CL* ENABLE
1k TEST POINT
ANALOG OUT
90% 50%
VOH HIGH IMPEDANCE
6 7 8
Figure 11a. Propagation Delays, Enable to Analog Out
Figure 11b. Propagation Delay, Test Set-Up Enable to Analog Out
MOTOROLA
10
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
VCC VIS VCC RL fin 0.1F OFF VEE RL 6 7 8 *Includes all probe and jig capacitance RL CL* RL CL* VEE 6 7 8 VCC 11 ON 16 VOS ANALOG I/O OFF/ON ON/OFF 16 COMMON O/I NC A
CHANNEL SELECT
Figure 12. Crosstalk Between Any Two Switches, Test Set-Up
0 VCC 16 ON RL CL* VOS TO DISTORTION METER dB - 10 - 20 - 30 - 40 - 50 - 60 6 7 8 VEE *Includes all probe and jig capacitance - 70 - 80 - 90 - 100
Figure 13. Power Dissipation Capacitance, Test Set-Up
VIS 0.1F fin
FUNDAMENTAL FREQUENCY
DEVICE SOURCE
1.0
2.0 FREQUENCY (kHz)
3.125
Figure 14a. Total Harmonic Distortion, Test Set-Up
Figure 14b. Plot, Harmonic Distortion
APPLICATIONS INFORMATION
The Channel Select and Enable control pins should be at VCC or GND logic levels. VCC being recognized as a logic high and GND being recognized as a logic low. In this example: VCC = +5V = logic high GND = 0V = logic low The maximum analog voltage swings are determined by the supply voltages VCC and VEE. The positive peak analog voltage should not exceed VCC. Similarly, the negative peak analog voltage should not go below VEE. In this example, the difference between VCC and VEE is ten volts. Therefore, using the configuration of Figure 15, a maximum analog signal of ten volts peak-to-peak can be controlled. Unused analog inputs/outputs may be left floating (i.e., not connected). However, tying unused analog inputs and outputs to VCC or GND through a low value resistor helps minimize crosstalk and feedthrough noise that may be picked up by an unused switch. Although used here, balanced supplies are not a requirement. The only constraints on the power supplies are that: VCC - GND = 2 to 6 volts VEE - GND = 0 to -6 volts VCC - VEE = 2 to 12 volts and VEE GND When voltage transients above VCC and/or below VEE are anticipated on the analog channels, external Germanium or Schottky diodes (Dx) are recommended as shown in Figure 16. These diodes should be able to absorb the maximum anticipated current surges during clipping.
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
11
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
VCC +5V -5V Dx Dx VEE 6 7 8 -5V 11 10 9 TO EXTERNAL CMOS CIRCUITRY 0 to 5V DIGITAL SIGNALS VEE VCC Dx Dx VEE
+5V +5V -5V 16 ANALOG SIGNAL ON ANALOG SIGNAL
VCC 16 ON/OFF
7 8
Figure 15. Application Example
Figure 16. External Germanium or Schottky Clipping Diodes
+5V +5V VEE 16 ANALOG SIGNAL ON/OFF ANALOG SIGNAL +5V * R R +5V VEE R LSTTL/NMOS CIRCUITRY VEE 6 7 8 11 10 9 +5V VEE 16 ANALOG SIGNAL ON/OFF
+5V ANALOG SIGNAL +5V VEE +5V LSTTL/NMOS CIRCUITRY HCT BUFFER
6 7 8 VEE
11 10 9 * 2K R 10K
a. Using Pull-Up Resistors
b. Using HCT Interface
Figure 17. Interfacing LSTTL/NMOS to CMOS Inputs
11 LEVEL SHIFTER 13
A
X0
14
X1
B
10
LEVEL SHIFTER
15
X2
12
X3
C
9
LEVEL SHIFTER
1
X4
5
X5
ENABLE
6
LEVEL SHIFTER
2
X6
4
X7
3
Figure 18. Function Diagram, VHC4051
X
MOTOROLA
12
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
10 LEVEL SHIFTER 12
A
X0
14
X1
B
9
LEVEL SHIFTER
15
X2
11 13 ENABLE 6 LEVEL SHIFTER 1
X3 X Y0
5
Y1
2
Y2
4
Y3
3
Y
Figure 19. Function Diagram, VHC4052
A
11
LEVEL SHIFTER
13
X1
12 14 B 10 LEVEL SHIFTER 1
X0 X Y1
2 15 C 9 LEVEL SHIFTER 3
Y0 Y Z1
5 4 ENABLE 6 LEVEL SHIFTER
Z0 Z
Figure 20. Function Diagram, VHC4053
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
13
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
OUTLINE DIMENSIONS
D SUFFIX PLASTIC SOIC PACKAGE CASE 751B-05 ISSUE J
9
-A -
16
-B -
1 8
P 8 PL 0.25 (0.010)
M
B
M
G F
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 9.80 10.00 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 BSC 0.25 0.19 0.25 0.10 7 0 6.20 5.80 0.50 0.25 INCHES MIN MAX 0.386 0.393 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0 7 0.229 0.244 0.010 0.019
K C -T SEATING -
PLANE
R X 45
M D 16 PL 0.25 (0.010)
M
J
T
B
S
A
S
MOTOROLA
14
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
MC74VHC4051 MC74VHC4052 MC74VHC4053
OUTLINE DIMENSIONS
DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948F-01 ISSUE O
M
16X K REF
0.10 (0.004) 0.15 (0.006) T U
S
TU
S
V
S
K K1
16
2X
L/2
9
J1 B -U-
L
PIN 1 IDENT. 1 8
SECTION N-N J
N 0.25 (0.010) 0.15 (0.006) T U
S
A -V- N F DETAIL E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.18 0.28 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.007 0.011 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_
M
DIM A B C D F G H J J1 K K1 L M
C 0.10 (0.004) -T- SEATING
PLANE
H D G
DETAIL E
VHC Data - Advanced CMOS Logic DL203 -- Rev 2
15
EE CC EE CC
-W-
MOTOROLA
MC74VHC4051 MC74VHC4052 MC74VHC4053
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140 or 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com - TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, Motorola Fax Back System - US & Canada ONLY 1-800-774-1848 2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. - http://sps.motorola.com/mfax/ 852-26668334 HOME PAGE: http://motorola.com/sps/ JAPAN: Motorola Japan Ltd.; SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan. 81-3-5487-8488
MOTOROLA 16
MC74VHC4051/D VHC Data - Advanced CMOS Logic DL203 -- Rev 2

▲Up To Search▲

Price & Availability of ON1724

	To Download ON1724 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .