|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
14-Bit, 200 MSPS/500 MSPS TxDAC+(R) with 2x/4x/8x Interpolation and Signal Processing Preliminary Technical Data FEATURES 14-bit resolution, 200 MSPS input data rate Selectable 2x/4x/8x interpolation filters Selectable fDAC/2, fDAC/4, fDAC/8 modulation modes Single or dual-channel signal processing Selectable image rejection Hilbert transform Flexible calibration engine Direct IF transmission features Serial control interface Versatile clock and data interface SFDR: 90 dBc @10 MHz WCDMA ACLR = 80 dBc @ 40 MHz IF DNL = 0.75 LSB INL = 1.5 LSB 3.3 V compatible digital Interface On-chip 1.2 V reference 80-lead thermally enhanced TQFP package APPLICATIONS Digital quadrature modulation architectures Multicarrier WCDMA, GSM, TDMA, DCS, PCS, CDMA Systems AD9784 PRODUCT DESCRIPTION The AD9784 is a 14-bit, high speed, CMOS DAC with 2x/4x/8x interpolation and signal processing features tuned for communications applications. It offers state of the art distortion and noise performance. The AD9784 was developed to meet the demanding performance requirements of multicarrier and third generation base stations. The selectable interpolation filters simplify interfacing to a variety of input data rates while also taking advantage of oversampling performance gains. The modulation modes allow convenient bandwidth placement and selectable sideband suppression. The flexible clock interface accepts a variety of input types such as 1 V p-p sine wave, CMOS, and LVPECL in single ended or differential mode. Internal dividers generate the required data rate interface clocks. The AD9784 provides a differential current output, supporting single-ended or differential applications; it provides a nominal full-scale current from 10 mA to 20 mA. The AD9784 is manufactured on an advanced low cost 0.25 m CMOS process. FUNCTIONAL BLOCK DIAGRAM LATCH 2x 2x 2x CALIBRATION I 0 t REFERENCE CIRCUITS FSADJ REFIO DATA ASSEMBLER 90 fDAC/2 fDAC/4 fDAC/8 0 90 0 90 P1B[15:0] P2B[15:0] Re()/Im() ZERO STUFF 16-BIT DAC IOUTA IOUTB SDIO HILBERT SDO SPI DATA PORT SYNCHRONIZER CSB SCLK RESET x1 LATCH 2x x2 2x x4 2x x8 DATACLK/ PLL_LOCK CLK- LPF CLOCK DISTRIBUTION AND CONTROL Figure 1. Rev. PrC Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 (c) 2004 Analog Devices, Inc. All rights reserved. 03152-PrD-001 CLK+ CLOCK MULTIPLIER x1/x2/x4/x8/x16 Q x2/x4/x8/x16 AD9784 TABLE OF CONTENTS Product Highlights ........................................................................... 3 AD9784-Specifications.................................................................... 4 DC Specifications ......................................................................... 4 Dynamic Specifications ............................................................... 5 Digital Specifications ................................................................... 6 Pin Configuration and Function Descriptions............................. 7 Clock .............................................................................................. 7 Analog............................................................................................ 8 Data ................................................................................................ 8 Serial Interface .............................................................................. 9 Definitions of Specifications ......................................................... 10 Typical Performance Charatceristics ........................................... 12 Serial Control Interface.................................................................. 17 General Operation of the Serial Interface ............................... 17 Instruction Byte .......................................................................... 17 Serial Interface Port Pin Descriptions ..................................... 17 MSB/LSB Transfers..................................................................... 18 Notes on Serial Port Operation ................................................ 18 Mode Control (via SPI Port) ......................................................... 19 Preliminary Technical Data Digital Filter Specifications ........................................................... 23 Digital Interpolation Filter Coefficients.................................. 23 AD9784 Clock/Data Timing..................................................... 24 Interpolation Modes .................................................................. 27 Real and Complex Signals......................................................... 28 Modulation Modes..................................................................... 29 Power Dissipation ...................................................................... 34 Dual Channel Complex Modulation with Hilbert ................ 35 Hilbert Transform Implementation......................................... 36 Operating the AD9784 Rev E Evaluation Board........................ 40 Power Supplies............................................................................ 40 PECL Clock Driver .................................................................... 40 Data Inputs.................................................................................. 41 SPI Port ........................................................................................ 41 Operating with PLL Disabled ................................................... 41 Operating with PLL Enabled .................................................... 42 Analog Output ............................................................................ 42 Outline Dimensions ....................................................................... 52 ESD Caution................................................................................ 52 REVISION HISTORY Revision PrC: Preliminary Version Rev. PrC | Page 2 of 52 Preliminary Technical Data PRODUCT HIGHLIGHTS 1. 2. 3. 4. 5. The AD9784 is a member of a high speed interpolating TxDAC+ family with 16-/14-/12-bit resolutions. 2x/4x/8x user selectable interpolating filter eases data rate and output signal reconstruction filter requirements. 200 MSPS input data rate. Ultrahigh speed 500 MSPS DAC conversion rate. Internal PLL/clock divider provides data rate clock for easy interfacing. 8. 6. 7. AD9784 Flexible clock with single-ended or differential input: CMOS, 1 V p-p sine wave and LVPECL capability. Complete CMOS DAC function operates from a 2.7 V to 3.6 V single analog (AVDD) supply and a 2.5 V (DVDD) digital supply. The DAC full-scale current can be reduced for lower power operation, and a sleep mode is provided for low-power idle periods. On-chip voltage reference: The AD9784 includes a 1.20 V temperature-compensated band gap voltage reference. Rev. PrC | Page 3 of 52 AD9784 AD9784-SPECIFICATIONS DC SPECIFICATIONS Preliminary Technical Data Table 1. TMIN to TMAX, AVDD1, AVDD2 = 3.3 V, ACVDD, ADVDD, CLKVDD, DVDD, DRVDD = 2.5 V, IOUTFS = 20 mA, unless otherwise noted Parameter RESOLUTION DC Accuracy1 Integral Nonlinearity Differential Nonlinearity ANALOG OUTPUT Offset Error Gain Error (Without Internal Reference) Gain Error (With Internal Reference) Full-Scale Output Current2 Output Compliance Range Output Resistance Output Capacitance REFERENCE OUTPUT Reference Voltage Reference Output Current3 REFERENCE INPUT Input Compliance Range Reference Input Resistance (Ext Reference Mode) Small Signal Bandwith TEMPERATURE COEFFICIENTS Unipolar Offset Drift Gain Drift (Without Internal Reference) Gain Drift (With Internal Reference) Reference Voltage Drift POWER SUPPLY AVDD1, AVDD2 Voltage Range Analog Supply Current (IAVDD1) Analog Supply Current (IAVDD2) IAVDD1 in SLEEP Mode ACVDD, ADVDD Voltage Range Analog Supply Current (IACVDD) Analog Supply Current (IADVDD) CLKVDD Voltage Range Clock Supply Current (ICLKVDD) DVDD Voltage Range Digital Supply Current (IDVDD) DRVDD Voltage Range Digital Supply Current (IDRVDD) Nominal Power Dissipation4 OPERATING RANGE Min Typ 14 1.5 0.75 Max Unit Bits LSB LSB % of FSR % of FSR % of FSR mA V k pF V A V M MHz ppm of FSR/C ppm of FSR/C ppm of FSR/C ppm /C 10 -1.0 TBD 3 1.14 1.20 1 20 +1.0 1.26 0.1 10 0.5 1.25 3.1 3.3 3.5 V mA mA mA V mA mA V mA V mA V mA W C 2.35 2.5 2.65 2.35 2.5 2.65 2.35 2.5 2.65 2.35 2.5/3.3 1.25 3.5 -40 +85 1 2 Measured at IOUTA driving a virtual ground. Nominal full-scale current, IOUTFS, is 32x the IREF current. 3 Use an external amplifier to drive any external load. 4 Measured under the following conditions: fDATA = 125 MSPS, fDAC = 500 MSPS, 4x Interpolation, fDAC/4 Modulation, Hilbert Off. Rev. PrC | Page 4 of 52 Preliminary Technical Data DYNAMIC SPECIFICATIONS Table 2. TMIN to TMAX, AVDD1, AVDD2 = 3.3 V, ACVDD, ADVDD, CLKVDD, DVDD, DRVDD = 2.5 V, IOUTFS = 20 mA, Differential Transformer Coupled Output, 50 Doubly Terminated, unless otherwise noted Parameter DYNAMIC PERFORMANCE Maximum DAC Output Update Rate (fDAC) Output Settling Time (tST) (to 0.025%) Output Propogation Delay5 (tPD) Output Rise Time (10%-90%)6 Output Fall Time (90%-10%)6 Output Noise (IOUTFS = 20 mA) AC LINEARITY--BASEBAND MODE Spurious-Free Dynamic Range (SFDR) to Nyquist (fOUT = 0 dBFS) fDATA = 160 MSPS; fOUT= 1 MHz fDATA = MSPS; fOUT = MHz fDATA = MSPS; fOUT = MHz fDATA = MSPS; fOUT = MHz fDATA = MSPS; fOUT = MHz fDATA = MSPS; fOUT = MHz Two-Tone Intermodulation (IMD) to Nyquist (fOUT1 = fOUT2 = -6 dBFS) fDATA = 160 MSPS; fOUT1 = 25 MHz; fOUT2 = 31 MHz fDATA = MSPS; fOUT1 = MHz; fOUT2 = MHz fDATA = MSPS; fOUT1 = MHz; fOUT2 = MHz fDATA = MSPS; fOUT1 = MHz; fOUT2 = MHz fDATA = MSPS; fOUT1 = MHz; fOUT2 = MHz fDATA = MSPS; fOUT1 = MHz; fOUT2 = MHz Total Harmonic Distortion (THD) fDATA = MSPS; fOUT = MHz; 0 dBFS fDATA = MSPS; fOUT = MHz; 0 dBFS Signal-to-Noise Ratio (SNR) fDATA = MSPS; fOUT = MHz; 0 dBFS fDATA = MSPS; fOUT = MHz; 0 dBFS Adjacent Channel Power Ratio (ACPR) WCDMA with MHz BW, MHz Channel Spacing IF = 16 MHz, fDATA = 65.536 MSPS IF = 32 MHz, fDATA = 131.072 MSPS Four-Tone Intermodulation MHz, MHz, MHz and MHz at -12 dBFS (fDATA = MSPS, Missing Center) AC LINEARITY--IF MODE Four-Tone Intermodulation at IF = MHz MHz, MHz, MHz and MHz at dBFS fDATA = MSPS, fDAC = MHz Min 500 Typ Max AD9784 Unit MSPS ns ns ns ns pAHz 95 dBc dBc dBc dBc dBc 80 dBc dBc dBc dBc dBc dBc dB dB dBFS dBFS dBc dBc dBFS dBFS 5 6 Propagation delay is delay from CLK input to DAC update. Measured single-ended into 50 load. Rev. PrC | Page 5 of 52 AD9784 DIGITAL SPECIFICATIONS Preliminary Technical Data Table 3. TMIN to TMAX, AVDD1, AVDD2 = 3.3 V, ACVDD, ADVDD, CLKVDD, DVDD = 2.5 V, IOUTFS = 20 mA, unless otherwise noted Parameter DIGITAL INPUTS Logic 1 Voltage Logic 0 Voltage Logic 1 Current Logic 0 Current Input Capacitance LOCK INPUTS Input Voltage Range Common-Mode Voltage Differential Voltage PLL CLOCK ENABLED Input Setup Time (ts) Input Hold Time (tH) Latch Pulse Width (tLPW) PLL CLOCK DISABLED Input Setup Time (ts) Input Hold Time (tH) Latch Pulse Width (tLPW) CLK to PLLLOCK Delay (tOD) Min DRVDD - 0.9 -10 -10 5 0 0.75 0.5 2.65 2.25 Typ DRVDD 0 Max Unit V V A A pF V V V ns ns ns ns ns ns ns 0.9 +10 +10 1.5 1.5 Rev. PrC | Page 6 of 52 Preliminary Technical Data PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADGND ACVDD ACGND ACGND ADGND ADVDD ACVDD ADVDD AGND2 AGND1 AGND1 AVDD1 AGND2 AVDD2 AVDD1 AVDD2 IOUTA IOUTB 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 AD9784 DNC NC CLKVDD 1 LPF 2 CLKVDD 3 CLKGND 4 CLK+ 5 CLK- 6 CLKGND 7 DGND 8 DVDD 9 P1B15 10 P1B14 11 P1B13 12 P1B12 13 P1B11 14 P1B10 15 DGND 16 DVDD 17 P1B9 18 P1B8 19 P1B7 20 PIN 1 IDENTIFIER 60 59 58 57 56 55 54 53 FSADJ REFIO RESET CSB SCLK SDIO SDO DGND DVDD P2B0 P2B1 P2B2 P2B3 P2B4 P2B5 DGND DVDD P2B6 P2B7 P2B8 AD9784 TOP VIEW (Not to Scale) 52 51 50 49 48 47 46 45 44 43 42 41 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 DRVDD DATACLK/PLL_LOCK IQSEL/P2B15 ONEPORTCLOCK/P2B14 P2B13 P2B12 P2B11 NC = NO CONNECT P2B10 P2B9 P1B6 P1B5 P1B4 P1B3 P1B2 P1B1 DVDD P1B0 DGND DVDD DGND Figure 2. Pin Configuration CLOCK Table 4. Clock Pin Function Descriptions Pin No. 5, 6 2 31 Mnemonic CLK+, CLK- LPF DATACLK/PLL_LOCK Direction I I/O I/O Description Differential Clock Input. PLL Loop Filter. PLOCKEXT DCLKEXT 04h[0] 02h[3] 0 0 0 1 1 X Mode Pin configured for input of channel data rate or synchronizer clock. Internal clock synchronizer may be turned on or off with DCLKCRC (02h[2]). Pin configured for output of channel data rate or synchronizer clock Internal Clock PLL Status Output: 0: Internal clock PLL is not locked. 1: Internal clock PLL is locked. 1, 3 4, 7 CLKVDD CLKGND Clock Domain 2.5 V. Clock Domain 0 V. Rev. PrC | Page 7 of 52 03151-PrD-001 AD9784 ANALOG Table 5. Analog Pin Function Descriptions Pin No. 59 60 70, 71 61 62, 79 63, 78 64, 77 65, 76 66, 75 67, 74 68, 73 69, 72 Mnemonic REFIO FSADJ IOUTB, IOUTA DNC ADVDD ADGND ACVDD ACGND AVDD2 AGND2 AVDD1 AGND1 Direction A A A Preliminary Technical Data Description Reference. Full-Scale Adjust. Differential DAC Output Currents. Do not connect. Analog Domain Digital Content 2.5 V. Analog Domain Digital Content 0 V. Analog Domain Clock Content 2.5 V. Analog Domain Clock Content 0 V. Analog Domain Clock Switching 3.3 V. Analog Domain Switching 0 V. Analog Domain Quiet 3.3 V. Analog Domain Quiet 0 V. DATA Table 6. Data Pin Function Descriptions Pin No. 10-15, 18-24, 27-29 Mnemonic P1B15-P1B0 Direction I Description Input Data Port One. ONEPORT 02h[6] Mode 0 Latched Data Routed for 1 Channel Processing. 1 Latched Data Demultiplexed by IQSEL and Routed for Interleaved I/Q Processing. ONEPORT IQPOL IQSEL/ 02h[6] 02h[1] P2B15 Mode (IQPOL == 0) 0 X X Latched data routed to Q channel bit 15(MSB) processing. 1 0 0 Latched data on data port one routed to Q channel processing. 1 0 1 Latched data on data port one routed to I channel processing. 1 1 0 Latched data on data port one routed to I channel processing. 1 1 1 Latched data on data port one routed to Q channel processing. ONEPORT 02h[6] 0 Latched data routed for Q channel Bit 14 processing. 1 Pin configured for output of clock at twice the channel data route. Input Data Port Two Bits 13-0. Digital Output Pin Supply, 2.5 V or 3.3 V. Digital Domain 2.5 V. Digital Domain 0 V. 32 IQSEL/P2B15 I 33 ONEPORTCLK/P2B14 I/O 34, 37-43, 46-51 30 9, 17, 26, 36, 44, 52 8, 16, 25, 35, 45, 53 P2B13-P2B0 DRVDD DVDD DGND I Rev. PrC | Page 8 of 52 Preliminary Technical Data SERIAL INTERFACE Table 7. Serial Interface Pin Function Descriptions Pin No. 54 Mnemonic SDO Direction O AD9784 55 SDIO I/O 56 57 58 SCLK CSB RESET I I I Description SDIODIR CSB 00h[7] Mode 1 X High Impedance. 0 0 Serial Data Output. 0 1 High Impedance. SDIODIR CSB 00h[7] Mode 1 X High Impedance. 0 0 Serial Data Output. 0 1 Serial Data Input/Output Depending on Bit 7 of the Serial Instruction Byte. Serial interface clock. Serial interface chip select. Resets entire chip to default state. Rev. PrC | Page 9 of 52 AD9784 DEFINITIONS OF SPECIFICATIONS Linearity Error (Integral Nonlinearity or INL) Linearity error is defined as the maximum deviation of the actual analog output from the ideal output, determined by a straight line drawn from zero to full scale. Differential Nonlinearity (or DNL) DNL is the measure of the variation in analog value, normalized to full scale, associated with a 1 LSB change in digital input code. Monotonicity A D/A converter is monotonic if the output either increases or remains constant as the digital input increases. Offset Error The deviation of the output current from the ideal of zero is called offset error. For IOUTA, 0 mA output is expected when the inputs are all 0s. For IOUTB, 0 mA output is expected when all inputs are set to 1s. Gain Error The difference between the actual and ideal output span. The actual span is determined by the output when all inputs are set to 1s, minus the output when all inputs are set to 0s. Output Compliance Range The range of allowable voltage at the output of a current-output DAC. Operation beyond the maximum compliance limits may cause either output stage saturation or breakdown, resulting in nonlinear performance. Temperature Drift Temperature drift is specified as the maximum change from the ambient (+25C) value to the value at either TMIN or TMAX. For offset and gain drift, the drift is reported in ppm of full-scale range (FSR) per degree C. For reference drift, the drift is reported in ppm per degree C. Power Supply Rejection The maximum change in the full-scale output as the supplies are varied from minimum to maximum specified voltages. Settling Time The time required for the output to reach and remain within a specified error band about its final value, measured from the start of the output transition. Stop-Band Rejection Interpolation Filter Glitch Impulse Preliminary Technical Data Asymmetrical switching times in a DAC give rise to undesired output transients that are quantified by a glitch impulse. It is specified as the net area of the glitch in pV-s. Spurious-Free Dynamic Range The difference, in dB, between the rms amplitude of the output signal and the peak spurious signal over the specified bandwidth. Total Harmonic Distortion THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured fundamental. It is expressed as a percentage or in decibels (dB). Signal-to-Noise Ratio (SNR) S/N is the ratio of the rms value of the measured output signal to the rms sum of all other spectral components below the Nyquist frequency, excluding the first six harmonics and dc. The value for SNR is expressed in decibels. If the digital inputs to the DAC are sampled at a multiple rate of fDATA (interpolation rate), a digital filter can be constructed which has a sharp transition band near fDATA/2. Images which would typically appear around fDAC (output data rate) can be greatly suppressed. Pass-Band Frequency band in which any input applied therein passes unattenuated to the DAC output. The amount of attenuation of a frequency outside the passband applied to the DAC, relative to a full-scale signal applied at the DAC input within the pass-band. Group Delay Number of input clocks between an impulse applied at the device input and peak DAC output current. A half-band FIR filter has constant group delay over its entire frequency range Impulse Response Response of the device to an impulse applied to the input. Rev. PrC | Page 10 of 52 Preliminary Technical Data Adjacent Channel Power Ratio (or ACPR) A ratio in dBc between the measured power within a channel relative to its adjacent channel. Complex Modulation The process of passing the real and imaginary components of a signal through a complex modulator (transfer function = ejwt = coswt + jsinwt) and realizing real and imaginary components on the modulator output. Complex Image Rejection AD9784 In a traditional two part upconversion, two images are created around the second IF frequency. These images are redundant and have the effect of wasting transmitter power and system bandwidth. By placing the real part of a second complex modulator in series with the first complex modulator, either the upper or lower frequency image near the second IF can be rejected. Rev. PrC | Page 11 of 52 AD9784 TYPICAL PERFORMANCE CHARATCERISTICS Preliminary Technical Data (TMIN to TMAX, AVDD1, AVDD2 = 3.3 V, ACVDD, ADVDD, CLKVDD, DVDD, DRVDD = 2.5 V, IOUTFS = 20 mA, Differential Transformer Coupled Output, 50 Doubly Terminated, unless otherwise noted) -000 -000 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 3 Single-Tone Spectrum@ FDATA = 65 MSPS With FOUT = FDATA/3 -000 Figure 6. Single-Tone Spectrum @ FDATA = 78 MSPS with FOUT = FDATA/3 -000 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 4. In-Band SFDR vs. FOUT @ FDATA = 65 MSPS -000 -000 Figure 7. In-Band SFDR Vs. FOUT @ FDATA = 78 MSPS ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 5. Out-of-Band SFDR vs. FOUT @ FDATA = 65 MSPS Figure 8. Out-of-Band SFDR vs. FOUT @ FDATA = 78 MSPS Rev. PrC | Page 12 of 52 Preliminary Technical Data -000 -000 AD9784 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 9. Single-Tone Spectrum @ FDATA = 160 MSPS with FOUT = FDATA/3 -000 Figure 12. Third Order IMD Products vs. FOUT @ FDATA = 65 MSPS -000 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 10. In-Band SFDR vs. FOUT @ FDATA = 160 MSPS -000 Figure 13. Third Order IMD Products vs. FOUT @ FDATA = 78 MSPS -000 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 11. Out-of-Band SFDR vs. FOUT @ FDATA = 160 MSPS Figure 14. Third Order IMD Products vs. FOUT @ FDATA = 160 MSPS Rev. PrC | Page 13 of 52 AD9784 -000 Preliminary Technical Data -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 15. TPC 13. Third Order IMD Products vs. FOUT and Interpolation Rate 1x - FDATA = 160 MSPS 2x - FDATA = 160 MSPS 4x - FDATA = 80 MSPS 8x - FDATA = 50 MSPS -000 Figure 18. 3rd Order IMD Products vs. AVDD @ FOUT = 10 MHz, FDAC = 320 MSPS, FDATA = 160 MSPS -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 19. SNR vs. Data Rate for fOUT = 5 MHz Figure 16. Third Order IMD Products vs. AOUT and Interpolation Rate FDATA = 50 MSPS for All Cases 1x - FDAC = 50 MSPS 2x - FDAC = 100 MSPS 4x - FDAC = 200 MSPS 8x - FDAC = 400 MSPS -000 -000 ALL CAPS (Initial caps) ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 17. SFDR vs. AVDD @ FOUT = 10 MHz; FDAC = 320 MSPS FDATA = 160 MSPS Figure 20. SFDR vs. Temperature @ fOUT = fDATA/11 Rev. PrC | Page 14 of 52 Preliminary Technical Data -000 -000 AD9784 ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 21. Single Tone Spurious Performance, fOUT = 10 MHz, fDATA = 150 MSPS, No Interpolation -000 Figure 24. Two Tone IMD Performance, FDATA = 90 MSPS, Interpolation = 4x -000 ALL CAPS (Initial caps) ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 22. Two Tone IMD Performance, FDATA = 150 MSPS, No Interpolation Figure 25. Single Tone Spurious Performance, FOUT = 10 MHz, FDATA = 80 MSPS, Interpolation = 4x -000 -000 ALL CAPS (Initial caps) ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 23. Single Tone Spurious Performance, FOUT = 10 MHz, FDATA = 150 MSPS, Interpolation = 2x Figure 26. Two Tone IMD Performance, FOUT = 10 MHz, FDATA = 50 MSPS, Interpolation = 8x Rev. PrC | Page 15 of 52 AD9784 -000 -000 Preliminary Technical Data ALL CAPS (Initial caps) -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 ALL CAPS (Initial caps) -000 -000 -000 TBD -000 -000 -000 ALL CAPS (Initial caps) -000 -000 -000 -000 -000 -000 -000 Figure 27. Single Tone Spurious Performance, FOUT = 10 MHz, FDATA = 50 MSPS, Interpolation = 8x Figure 28. Eight Tone IMD Performance, FDATA = 160 MSPS, Interpolation = 8x Rev. PrC | Page 16 of 52 Preliminary Technical Data SERIAL CONTROL INTERFACE SDO (PIN 54) SDIO (PIN 55) SCLK (PIN 56) CSB (PIN 57) 03151-PrD-002 AD9784 INSTRUCTION BYTE AD9784 SPI PORT INTERFACE The instruction byte contains the following information: Table 8. N1 0 0 1 1 N2 0 1 0 1 Description Transfer 1 Byte Transfer 2 Bytes Transfer 3 Bytes Transfer 4 Bytes Figure 29. AD9784 SPI Port Interface The AD9784 serial port is a flexible, synchronous serial communications port allowing easy interface to many industrystandard microcontrollers and microprocessors. The serial I/O is compatible with most synchronous transfer formats, including both the Motorola SPI(R) and Intel(R) SSR protocols. The interface allows read/write access to all registers that configure the AD9784. Single or multiple byte transfers are supported as well as MSB first or LSB first transfer formats. The AD9784's serial interface port can be configured as a single pin I/O (SDIO) or two unidirectional pins for in/out (SDIO/SDO). R/W, Bit 7 of the instruction byte, determines whether a read or a write data transfer will occur after the instruction byte write. Logic high indicates read operation. Logic 0 indicates a write operation. N1, N0, Bits 6 and 5 of the instruction byte, determine the number of bytes to be transferred during the data transfer cycle. The bit decodes are shown in the following table: Table 9. MSB 17 R/W 16 N1 15 N0 14 A4 13 A3 12 A2 11 A1 LSB 10 A0 GENERAL OPERATION OF THE SERIAL INTERFACE There are two phases to a communication cycle with the AD9784. Phase 1 is the instruction cycle, which is the writing of an instruction byte into the AD9784, coincident with the first eight SCLK rising edges. The instruction byte provides the AD9784 serial port controller with information regarding the data transfer cycle, which is Phase 2 of the communication cycle. The Phase 1 instruction byte defines whether the upcoming data transfer is read or write, the number of bytes in the data transfer, and the starting register address for the first byte of the data transfer. The first eight SCLK rising edges of each communication cycle are used to write the instruction byte into the AD9784. A logic high on the CS pin, followed by a logic low, will reset the SPI port timing to the initial state of the instruction cycle. This is true regardless of the present state of the internal registers or the other signal levels present at the inputs to the SPI port. If the SPI port is in the midst of an instruction cycle or a data transfer cycle, none of the present data will be written. The remaining SCLK edges are for Phase 2 of the communication cycle. Phase 2 is the actual data transfer between the AD9784 and the system controller. Phase 2 of the communication cycle is a transfer of 1, 2, 3, or 4 data bytes as determined by the instruction byte. Normally, using one multibyte transfer is the preferred method. However, single byte data transfers are useful to reduce CPU overhead when register access requires one byte only. Registers change immediately upon writing to the last bit of each transfer byte. A4, A3, A2, A1, A0, Bits 4, 3, 2, 1, 0 of the instruction byte, determine which register is accessed during the data transfer portion of the communications cycle. For multibyte transfers, this address is the starting byte address. The remaining register addresses are generated by the AD9784. SERIAL INTERFACE PORT PIN DESCRIPTIONS SCLK--Serial Clock. The serial clock pin is used to synchronize data to and from the AD9784 and to run the internal state machines. SCLK's maximum frequency is 15 MHz. All data input to the AD9784 is registered on the rising edge of SCLK. All data is driven out of the AD9784 on the falling edge of SCLK. CSB--Chip Select. Active low input starts and gates a communication cycle. It allows more than one device to be used on the same serial communications lines. The SDO and SDIO pins will go to a high impedance state when this input is high. Chip select should stay low during the entire communication cycle. SDIO--Serial Data I/O. Data is always written into the AD9784 on this pin. However, this pin can be used as a bidirectional data line. The configuration of this pin is controlled by Bit 7 of register address 00h. The default is Logic 0, which configures the SDIO pin as unidirectional. SDO--Serial Data Out. Data is read from this pin for protocols that use separate lines for transmitting and receiving data. In the case where the AD9784 operates in a single bidirectional I/O mode, this pin does not output data and is set to a high impedance state. Rev. PrC | Page 17 of 52 AD9784 MSB/LSB TRANSFERS The AD9784 serial port can support both most significant bit (MSB) first or least significant bit (LSB) first data formats. This functionality is controlled by register address DATADIR (00h[6]). The default is MSB first. When this bit is set active high, the AD9784 serial port is in LSB first format. That is, if the AD9784 is in LSB first mode, the instruction byte must be written from least significant bit to most significant bit. Multibyte data transfers in MSB format can be completed by writing an instruction byte that includes the register address of the most significant byte. In MSB first mode, the serial port internal byte address generator decrements for each byte required of the multibyte communication cycle. Multibyte data transfers in LSB first format can be completed by writing an instruction byte that includes the register address of the least significant byte. In LSB first mode, the serial port internal byte address generator increments for each byte required of the multibyte communication cycle. The AD9784 serial port controller address will increment from 1Fh to 00h for multibyte I/O operations if the MSB first mode is active. The serial port controller address will decrement from 00h to 1Fh for multibyte I/O operations if the LSB first mode is active. CSB SCLK Preliminary Technical Data INSTRUCTION CYCLE DATA TRANSFER CYCLE SDO D7 D6N D5N D30 D20 D10 D00 Figure 30. Serial Register Interface Timing MSB First INSTRUCTION CYCLE CSB DATA TRANSFER CYCLE SCLK SDO D00 D10 D20 D4N D5N D6N D7N Figure 31. Serial Register Interface Timing LSB First tDS CSB tSCLK NOTES ON SERIAL PORT OPERATION The AD9784 serial port configuration bits reside in Bits 6 and 7 of register address 00h. It is important to note that the configuration changes immediately upon writing to the last bit of the register. For multibyte transfers, writing to this register may occur during the middle of communication cycle. Care must be taken to compensate for this new configuration for the remaining bytes of the current communication cycle. The same considerations apply to setting the software reset, SWRST (00h[5]) bit. All other registers are set to their default values but the software reset doesn't affect the bits in register address 00h and 04h. It is recommended to use only single byte transfers when changing serial port configurations or initiating a software reset. SCLK tPWH tPWL tDH INSTRUCTION BIT 6 SDIO INSTRUCTION BIT 7 Figure 32. Timing Diagram for Register Write CSB SCLK tDV SDIO SDO DATA BIT n DATA BIT n -1 Figure 33. Timing Diagram for Register Read Rev. PrC | Page 18 of 52 03152-PrD-007 03152-PrD-006 tDS 03152-PrD-005 SDIO A0 A1 A2 A3 A4 N0 N1 R/W D00 D10 D20 D4N D5N D6N D7N 03152-PrD-004 SDIO R/W N1 N0 A4A 3A 2A 1A 0 D7 D6N D5N D30 D20 D10 D00 Preliminary Technical Data MODE CONTROL (VIA SPI PORT) Table 10. Address COMMS FILTER DATA MODULATE PLL DCLKCRC 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 Bit 7 SDIODIR INTERP[1] DATAFMT CHANNEL PLLON DATADJ[3] Bit 6 DATADIR INTERP[0] ONEPORT HILBERT PLLMULT[1] DATADJ[2] Bit 5 SWRST DCLKSTR MODDUAL PLLMULT[0] DATADJ[1] Bit 4 SLEEP Bit 3 PDN ZSTUFF DCLKPOL DCLKEXT SIDEBAND MOD[1] PLLDIV[1] PLLDIV[0] DATADJ[0] MODSYNC Reserved Reserved Reserved Reserved Reserved Reserved Reserved VERSION[3] CALMEN[0] XFEREN SMEMWR MEMADDR[4] MEMADDR[3] MEMDATA[4] MEMDATA[3] Bit 2 HPFX8 DCLKCRC MOD[0] PLLAZ[1] MODADJ[2] Bit 1 PLLLOCK HPFX4 IQPOL PLLAZ[0] MODADJ[1] AD9784 Bit 0 EXREF HPFX2 CRAYDIN PLOCKEXT MODADJ[0] VERSION CALMEMCK MEMRDWR MEMADDR MEMDATA DCRSTAT RESERVED CALSTAT MEMADDR[7] RESERVED CALEN MEMADDR[6] CALMEM[1] XFERSTAT MEMADDR[5] MEMDATA[5] VERSION[3] CALCKDIV[2] SMEMRD MEMADDR[2] MEMDATA[2] DCRSTAT[2] VERSION[3] CALCKDIV[2] FMEMRD MEMADDR[1] MEMDATA[1] DCRSTAT[1] VERSION[3] CALCKDIV[2] UNCAL MEMADDR[0] MEMDATA[0] DCRSTAT[0] Table 11. COMMS(00) SDIODIR DATADIR SWRST SLEEP PDN PLLOCK EXREF Bit 7 6 5 4 3 1 0 Direction I I I I I O I Default 0 0 0 0 0 0 0 Description 0: SDIO pin configured for input only during data transfer 1: SDIO configured for input or output during data transfer 0: Serial data uses MSB first format 1: Serial data uses LSB first format 1: Default all serial register bits, except addresses 00h and 04h 1: DAC output current off 1: All analog and digital circuitry, except serial interface, off 0: With PLL on, indicates that PLL is not locked 1: With PLL on, indicates that PLL is locked 0: Internal band gap reference 1: External reference Table 12. FILTER(01) INTERP[1:0] Bit [7:6] Direction I Default 00 Description 00: No interpolation 01: Interpolation 2x 10: Interpolation 4x 11: Interpolation 8x 1: Zero Stuffing on 0: x8 interpolation filter configured for low pass 1: x8 interpolation filter configured for high pass 0: x4 interpolation filter configured for low pass 1: x4 interpolation filter configured for high pass 0: x2 interpolation filter configured for low pass 1: x2 interpolation filter configured for high pass ZSTUFF HPFX8 HPFX4 HPFX2 3 2 1 0 I I I I 0 0 0 0 Rev. PrC | Page 19 of 52 AD9784 Table 13. DATA(02) DATAFMT ONEPORT DCLKSTR DCLKPOL DCLKEXT DCLKCRC IQPOL GRAYDIN Bit 7 6 5 4 3 2 1 0 Direction I I I I I I I I Default 0 0 0 0 0 0 0 0 Preliminary Technical Data Description 0: Twos complement data format 1: Unsigned binary input data format 0: I and Q input data onto ports one and two respectively 1: I and Q input data interleaved onto port one 0: DATACLK pin 12 mA drive strength 1: DATACLK pin 24 mA drive strength 0: Input data latched on DATACLK rising edge 1: Input data latched on DATACLK falling edge 0: With PLOCKEXT off, DATACLK pin inputs channel data rate or modulator synchronizer clock 1: With PLOCKEXT off, DATACLK pin outputs channel data rate or modulator synchronizer clock 0: With PLOCKEXT off, and DATACLK pin as input, DATACLK clock recovery off 1: With PLOCKEXT off, and DATACLK pin as input, DATACLK clock recovery on 0: In one port mode, IQSEL = 1 latches data into I channel, IQSEL = 0 latches data into Q channel 1: In one port mode, IQSEL = 0 latches data into I channel, IQSEL = 1 latches data into Q channel 0: Gray decoder off 1: Gray decoder on Table 14. MODULATE(03) CHANNEL Bit 7 Direction I Default 0 Description MODDUAL CHANNEL 03h [5] 03h[7] 0 0 I channel processing routed to DAC 0 1 Q channel processing routed to DAC 1 0 Modulator real output routed to DAC 1 1 Modulator imaginary output routed to DAC 1: With MODDUAL on, Hilbert transform on 0: Modulator uses a single channel 1: Modulator uses both I and Q channels 0: With MODDUAL on, lower sideband rejected 1: With MODDUAL on, upper sideband rejected 00: No modulation 01: fS/2 modulation 10: fS /4 modulation 11: fS /8 modulation HILBERT MODDUAL SIDEBAND MOD[1:0] 6 5 4 [3:2] I I I I 0 0 0 00 Rev. PrC | Page 20 of 52 Preliminary Technical Data Table 15. PLL(04) PLLON PLLMULTI[1:0] Bit 7 [6:5] Direction I I Default 0 00 AD9784 Description 0: PLL off 1: PLL on PLL MULTIPLY FACTOR 00: x2 00: x4 00: x8 00: x16 PLLMULT rate divide factor 00:/1 00:/2 00:/4 00:/8 PLL Autozero settling bandwidth as fraction of CLK rate 00: /8 (lowest) 01: /4 10: /2 (highest) 0: With PLL on, DATACLK/PLL_LOCK pin configured for DATACLK input/output 1: With PLL on, DATACLK/PLL_LOCK pin configured for output of PLLLOCK PLLDIV[1:0] [4:3] I 00 PLLAZBW[1:0] [2:1] I 00 PLOCKEXT 0 I 0 Table 16. DCLKCRC(05) DATADJ[3:0] Bit [7:4] Direction I Default 0000 Description DATACLK offset. Twos complement respresentation 0111: +7 : 0000: 0 : 1000: -8 0: With PLOCKEXT off, channel data rate clock synchronizer mode 1: With PLOCKEXT off, state machine clock synchronizer mode Modulator coefficient offset fS/8 fS/4 fS/2 000 1 1 1 001 1/2 0 -1 010 0 -1 1 011 -1/2 0 -1 100 -1 1 1 101 -1/2 0 -1 110 0 -1 1 111 1/2 0 -1 MODSYNC MODADJ[2:0] 3 [2:0] I I 00 000 Table 17. VERSION(0D) VERSION[3:0] Bit [3:0] Direction O Default - Description Hardware version identifier Rev. PrC | Page 21 of 52 AD9784 Table 18. CALMEMCK(OE) CALMEM Bit [5:4] Direction O Default 00 Preliminary Technical Data Description Calibration memory 00: Uncalibrated 01: Self Calibration 10: Factory calibration 11: User input Calibration clock divide ratio from channel data rate 000: /32 001: /64 : 110: /2048 111: /4096 CALCKDIV[2:0] [2:0] I 00 Table 19. MEMRDWR(OF) CALSTAT CALEN XFERSTAT XFEREN SMEMWR SMEMRD FMEMRD UNCAL Bit 7 6 5 4 3 2 1 0 Direction O I O I I I I I Default 0 0 0 0 0 0 0 0 Description 0: Self Calibration cycle not complete 1: Self Calibration cycle complete 1: Self Calibration in progress 0: Factory memory transfer not complete 1: Factory memory transfer complete 1: Factory memory transfer in progress 1: Write static memory data from external port 1: Read static memory to external port 1: Read factory memory data to external port 1: Use uncalibrated Table 20. MEMADDR(10) MEMADDR [7:0] Bit [7:0] Direction I/O Default 00000000 Description Address of factory or static memory to be accessed Table 21. MEMDATA(11) MEMDATA [5:0] Bit [5:0] Direction I/O Default 000000 Description Data or factory or static memory access Table 22. DCRCSTAT(12) DCRCSTAT (2) DCRCSTAT(1) DCRCSTAT(0) Bit 2 1 0 Direction O O O Default 0 0 0 Description 0: With DATACLK CRC on, lock has never been achieved 1: With DATACLK CRC on, lock has been achieved at least once 0: With DATACLK CRC on, system is currently not locked 1: With DATACLK CRC on, system is currently locked 0: With DATACLK CRC on, system is currently locked 1: With DATACLK CRC on, system lost lock due to jitter Rev. PrC | Page 22 of 52 Preliminary Technical Data DIGITAL FILTER SPECIFICATIONS DIGITAL INTERPOLATION FILTER COEFFICIENTS Table 23. Stage 1 Interpolation Filter Coefficients Lower Coefficient H(1) H(2) H(3) H(4) H(5) H(6) H(7) H(8) H(9) H(10) H(11) H(12) H(13) H(14) H(15) H(16) H(17) H(18) H(19) H(20) H(21) H(22) Upper Coefficient H(43) H(42) H(41) H(40) H(39) H(38) H(37) H(36) H(35) H(34) H(33) H(32) H(31) H(30) H(29) H(28) H(27) H(26) H(25) H(24) H(23) Integer Value 9 0 -27 0 65 0 -131 0 239 0 -407 0 665 0 -1070 0 1764 0 -3273 0 10358 16384 0 -20 -40 -60 -80 -100 -120 -140 -0.5 AD9784 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 34. x2 Interpolation Filter Response 0 -20 -40 -60 -80 -100 -120 Table 24. Stage 2 Interpolation Filter Coefficients Lower Coefficient H(1) H(2) H(3) H(4) H(5) H(6) H(7) H(8) H(9) H(10) Upper Coefficient H(19) H(18) H(17) H(16) H(15) H(14) H(13) H(12) H(11) Integer Value 19 0 -120 0 436 0 -1284 0 5045 8192 -140 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 35. x4 Interpolation Filter Response 0 -20 -40 -60 -80 Table 25. Stage 3 Interpolation Filter Coefficients Lower Coefficient H(1) H(2) H(3) H(4) H(5) H(6) Upper Coefficient H(11) H(10) H(9) H(8) H(7) Integer Value 7 0 -53 0 302 512 -100 -120 -140 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 36. x8 Interpolation Filter Response Rev. PrC | Page 23 of 52 03152-PrD-010 03152-PrD-009 03152-PrD-008 AD9784 AD9784 CLOCK/DATA TIMING DLL Disabled, Two-Port Data Mode, DATACLK as Output With the interpolation set to 1x, the DATACLK output is a delayed and inverted version of DACCLK at the same frequency. Note that DACCLK refers to the differential clock inputs applied at Pins 5 and 6. As Figure 37 shows, there is a constant delay between the rising edge of DACCLK and the falling edge of DATACLK. Preliminary Technical Data The DCLKPOL bit (Reg 02 Bit 4) allows the data to be latched into the AD9784 on either the rising or falling edge of DACCLK. With DCLKPOL = 1, the data is latched in on the rising edge of Diff Clk, as shown in Figure 37. With DCLKPOL = 0, as shown in Figure 38, data is latched in on the falling edge of DACCLK. The setup and hold times are always with respect to the latched edge of DACCLK. DACCLKIN DATACLKOUT tD = 5ns TYP tS = -0.5ns TYP t12 tH = 2.9ns TYP DATA 03152-PrD-066 03152-PrD-067 Figure 37. Data Timing, DLL Off, 1x Interpolation, DCLKPOL = 1 DACCLKIN DATACLKOUT tD = 6ns TYP tS = -0.5ns TYP tH = 2.9ns TYP DATA Figure 38. Data Timing, DLL Off, 1x Interpolation, DCLKPOL = 0 Rev. PrC | Page 24 of 52 Preliminary Technical Data With the interpolation set to 2x, the DACCLK input runs at twice the speed of the DATACLK. Data is latched into the AD9784's inputs on every other rising edge of DACCLK, as shown in Figure 40 and Figure 41. With DCLKPOL = 1, as shown in Figure 40, the latching edge of DACCLK is the rising edge that occurs just before the falling edge of DATACLK. With DCLKPOL = 0, as in Figure 41, the latching edge of DACCLK is the rising edge of DACCLK that occurs just before the rising edge of DATACLK. The setup and hold time values are identical to those in Figure 37 and Figure 38. Note that there is a slight difference in the delay from the rising edge of DACCLK to the falling edge of DATACLK, and the delay from the rising edge of DACCLK to the rising edge of DATACLK. As Figure 39 shows, the DATACLK duty cycle is slightly less than 50%. This is true in all modes. With the interpolation set to 4x or 8x, the DACCLK input runs at 4x or 8x the speed of the DATACLK output. The data is latched in on a rising edge of DACCLK, similar to the 2x interpolation mode. However, the latching edge is every fourth edge in 4x interpolation mode and every eighth edge in the 8x AD9784 interpolation mode. Again, similar to operation in the 2x interpolation mode, with DCLKPOL = 1, the latching edge of DACCLK is the rising edge that occurs just before the falling edge of DATACLK. With DCLKPOL = 0, the latching edge of DACCLK is the rising edge that occurs just before the rising edge of DATACLK. The setup and hold time values are identical to those in 1x and 2x interpolation Figure 39 DACCLKIN DATACLKOUT tD = 5ns TYP tS = -0.5ns TYP tH = 2.9ns TYP DATA 03152-PrD-069 Figure 40. Data Timing, DLL Off, 2x Interpolation, DCLKPOL = 1 DACCLKIN DATACLKOUT tD = 6ns TYP tS = -0.5ns TYP tH = 2.9ns TYP DATA 03152-PrD-070 Figure 41. Data Timing, DLL Off, 2x Interpolation, DCLKPOL = 0 Rev. PrC | Page 25 of 52 03152-PrD-068 AD9784 DATAADJUST Synchronization When designing the digital interface for high speed DACs, care must be taken to ensure that the DAC input data meets setupand-hold requirements. Often, compensation must be used in the clock delay path to the digital engine driving the DAC. The AD9784 has the on chip capability to vary the DACCLK's latching edge. With the interpolation function enabled, this allows the user the choice of multiple edges upon which to latch the data. For instance, if the AD9784 is using 8x interpolation, the user may latch from one of eight edges before the rising edge of DATACLK, or seven edges after this rising edge. The specific edge upon which data is latched is controlled by SPI Register 05h, Bits 7:4. Table 26 shows the relationship of the latching edge of DACCLK and DATACLK with the various settings of the DATAADJ bits. Table 26. Bit 7 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 SPI Reg 05h Bit 6 Bit 5 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 0 0 0 0 0 1 0 1 1 0 1 0 1 1 1 1 Bit 4 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Latching Edge wrt DATACLK 0 +1 +2 +3 +4 +5 +6 +7 -8 -7 -6 -5 -4 -3 -2 -1 Preliminary Technical Data Figure 42, Figure 43, and Figure 44 show the alignment for the latching edge of DACCLK with 4x interpolation and different settings for DATAADJ. In Figure 42, DATAADJ is set to 0000, with DCLKPOL set to 0 so that the latching edge of DACCLK is immediately before the rising edge of DATACLK. The data transitions shown in Figure 42 are synchronous with the DACCLK, so that DACCLK and data are constant with respect to each other. The only visible change when DATAADJ is altered is that DATACLK moves, indicating the latching edge has moved as well. Note that when DATAADJ is altered, the latching edge with respect to DATACLK remains the same, but the latching edge of DACCLK follows the edge of DATACLK. RISING EDGE OF DATACLK CONCURRENT WITH LATCHING EDGE OF DACCLK DACCLK LATCHING EDGE DATA TRANSITION Figure 42. DATAADJ = 0000 Figure 43 shows the same conditions, but now DATAADJ is set to 1111. This moves DATACLK to the left in the plot, indicating that it occurs one DACCLK cycle before it did in Figure 42. As explained previously, the latching edge of DACCLK also moves one cycle back in time. RISING EDGE OF DATACLK CONCURRENT WITH LATCHING EDGE OF DACCLK Note that the data in Figure 40 and Figure 41 was taken with the DATAADJ default of 0000. With DCLKPOL = 0, the latching edge of DACCLK is just previous to the rising edge of DATACLK; with DCLKPOL = 1, the latching edge of DACCLK is just previous to the falling edge of DATACLK. With 8x interpolation, the user has the capability of using one of 16 edges to latch the data. This is due to the fact that there are eight DAC clock edges before and after the DATACLK until the next DATACLK latching edge. With 4x interpolation, there are only four latching edges of DACCLK available before and after each DATACLK edge. Therefore, in 4x interpolation, only the even numbered values for DATAADJ are available, and the options are changed from +3 cycles to -4 cycles. With 2x interpolation, there are only two edges available before and after DATACLK, so the choices for DATAADJ are diminished to +1 cycle to -2 cycles. Rev. PrC | Page 26 of 52 DACCLK LATCHING EDGE DATA TRANSITION Figure 43. DATAADJ = 1111 03152-PrD-072 03152-PrD-071 Preliminary Technical Data Figure 44 shows the same conditions, with DATAADJ now set to 0001, thus moving DATACLK to the right in the plot. This indicates that it occurs one DACCLK cycle after it did in Figure 42. Now the latching edge of DACCLK moves forward in time one cycle. RISING EDGE OF DATACLK CONCURRENT WITH LATCHING EDGE OF DACCLK AD9784 The digital filter's frequency domain response exhibits symmetry about half the output data rate and dc. It will cause images of the input data to be shaped by the interpolation filter's frequency response. This has the advantage of causing input data images, which fall in the stop band of the digital filter to be rejected by the stop-band attenuation of the interpolation filter; input data images falling in the interpolation filter's passband will be passed. In band-limited applications, the images at the output of the DAC must be limited by an analog reconstruction filter. The complexity of the analog reconstruction filter is determined by the proximity of the closest image to the required signal band. Higher interpolation rates yield larger stop-band regions, suppressing more input images and resulting in a much relaxed analog reconstruction filter. A DAC shapes its output with a sinc function, having a null at the sampling frequency of the DAC. The higher the DAC sampling rate compared to the input signal bandwidth, the less the DAC sinc function will shape the output. Figure 45 shows the interpolation filters of the AD9784 under different interpolation rates, normalized to the input data rate, fSIN. The higher the interpolation rate the more input data images fall in the interpolation filter stop band and are rejected; the band-width between passed images is larger with higher interpolation factors. The sinc function shaping is also reduced with a higher interpolation factor. Table 28. Mode No Interpolation x2 Interpolation x4 Interpolation x8 Interpolation Sinc Shaping at 0.43fSIN (dB) -2.8241 -0.6708 -0.1657 -0.0413 Bandwidth to First Image fSIN 2fSIN 4fSIN 8fSIN DACCLK LATCHING EDGE DATA TRANSITION Figure 44. DATAADJ = 0001 INTERPOLATION MODES Table 27. INTERP[1] 0 0 1 1 INTERP[0] 0 1 0 1 Mode No Interpolation x2 Interpolation x4 Interpolation x8 Interpolation Interpolation is the process of increasing the number of points in a time domain waveform by approximating points between the input data points; on a uniform time grid, this produces a higher output data rate. Applied to an interpolation DAC, a digital interpolation filter is used to approximate the interpolated points, having an output data rate increased by the interpolation factor. Interpolation filter responses are achieved by cascading individual digital filter banks, whose filter coefficients are given in Table 1; filter responses are shown in Figure 34. 03152-PrD-073 Rev. PrC | Page 27 of 52 AD9784 SINC RESPONSE 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 -6 -4 -2 -0 2 4 Preliminary Technical Data NO INTERPOLATION INTERP[1] = 0 INTERP[0] = 0 6 8 fSIN x2 INTERPOLATION INTERP[1] = 0 INTERP[0] = 1 6 8 fSIN x4 INTERPOLATION INTERP[1] = 1 INTERP[0] = 0 6 8 fSIN x8 INTERPOLATION INTERP[1] = 1 INTERP[0] = 1 03152-PrD-011 8 fSIN Figure 45. Interpolation Modes REAL AND COMPLEX SIGNALS A complex signal contains both magnitude and phase information. Given two signals at the same frequency, if a point in time can be taken such that the signal leading in phase is cosinusoidal and the lagging signal is sinusoidal, then information pertaining to the magnitude and phase of a combination of the two signals can be derived; the combination of the two signals can be considered a complex signal. The cosine and sine can be represented as a series of exponentials; recalling that a multiplication by j is a counter clockwise rotation about the Re/Im plane, the phasor representation of a complex signal, with frequency f, can be shown Figure 46. Im Im Re C A/2 A/2 2ft A Re -f 0 +f FREQUENCY A/2 C = Ae2ft = Acos(2ft) + jAsin(2ft) 2 e+j2ft + e-j2ft 2j 2 A 2 03152-PrD-012 The cosine term represents a signal on the real plane with mirror symmetry about dc; this is referred to as the real, inphase or I component of a complex signal. The sine term represents a signal on the imaginary plane with mirror asymmetry about dc; this term is referred to as the imaginary, quadrature or Q complex signal component. The AD9784 has two channels of interpolation filters, allowing both I and Q components to be shaped by the same filter transfer function. The interpolation filters' frequency response is a real transfer function. Two DACs are required to represent a complex signal. A single DAC can only synthesize a real signal. When a DAC synthesizes a real signal, negative frequency components fold onto the positive frequency axis. If the input to the DAC is mirror symmetrical about dc, the folded negative frequency components fold directly onto the positive frequency components in phase producing constructive signal summation. If the input to the DAC is not mirror symmetric about dc, negative frequency components may not be in phase with positive frequency components and will cause destructive signal summation. Different applications may or may not benefit from either type of signal summation. A/2 Acos(2ft) = A Asin(2ft) = A e+j2ft + e-j2ft = = A [e+j2ft + e-j2ft] [je+j2ft + e-j2ft] Figure 46. Complex Phasor Representation Rev. PrC | Page 28 of 52 Preliminary Technical Data MODULATION MODES Table 29. Single Channel Modulation MODDUAL 0 0 0 0 0 0 0 0 CHANNEL 0 0 0 0 1 1 1 1 MOD[1] 0 0 1 1 0 0 1 1 MOD[0] 0 1 0 1 0 1 0 1 Mode I Channel, no modulation I Channel, modulation by fDAC/2 I Channel, modulation by fDAC/4 I Channel, modulation by fDAC/8 Q Channel, no modulation Q Channel, modulation by fDAC/2 Q Channel, modulation by fDAC/4 Q Channel, modulation by fDAC/8 AD9784 Either channel of the AD9784's interpolation filter channels can be routed to the DAC and modulated. In single channel operation the input data may be modulated by a real sinusoid; the input data and the modulating sinusoid will contain both positive and negative frequency components. A double sideband output results when modulating two real signals. At the DAC output the positive and negative frequency components will add in phase resulting in constructive signal summation. As the modulating sinusoidal frequency becomes a larger fraction of the DAC update rate, fDAC, the more the sinc function of the DAC shapes the modulated signal bandwidth, and the closer the first image moves. As the AD9784 interpolation filter's pass band represents a large portion of the input data's Nyquist band, under certain modulation and interpolation modes it is possible for modulated signal bands to touch or overlap images if sufficient interpolation is not used. Figure 48 shows the effect of real modulation under all interpolation modes. The sinc shaping at the corners of the modulated signal band and the bandwidth to the first image for those cases whose pass bands do not touch or overlap are tabulated. Table 30. Modulation none fDAC/2 fDAC/4 fDAC/8 None fSIN fSIN Overlap Overlap Interpolation x2 x4 2 fSIN 4 fSIN 2 fSIN 4 fSIN Touching 2 fSIN Overlap Touching x8 8 fSIN 8 fSIN 4 fSIN 6 fSIN Table 31. Modulation None fDAC/2 fDAC/4 fDAC/8 None 0 -2.8241 -0.0701 -22.5378 Overlap Overlap Interpolation x2 x4 0 0 -0.6708 -0.1657 -1.1932 -2.3248 -9.1824 -6.1190 Touching -0.2921 -1.9096 Overlap Touching x8 0 -0.0413 -3.0590 -4.9337 -0.5974 -1.3607 -0.0727 -0.4614 Modulated pass band edges sinc shaping(lower/upper). Rev. PrC | Page 29 of 52 AD9784 FILTERED INTERPOLATION IMAGES Preliminary Technical Data -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 0 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC fS/8 MODULATION fDAC 03152-PrD-014 -7fDAC/8 -3fDAC/4 -5fDAC/8 -3fDAC/8 Figure 47. Double Sideband Modulation 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 NO INTERPOLATION INTERP[1] = 0 INTERP[0] = 0 MOD[1] = 0 MOD[0] = 1 6 8 fSIN INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 0 MOD[0] = 1 x2 INTERPOLATION 6 8 fSIN INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 0 MOD[0] = 1 x4 INTERPOLATION 6 8 fSIN INTERP[1] = 1 INTERP[0] = 1 MOD[1] = 0 MOD[0] = 1 x8 INTERPOLATION 6 8 fSIN Figure 48. Real Modulation by fDAC/2 under all Interpolation Modes Rev. PrC | Page 30 of 52 03152-PrD-013 -fDAC/2 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC fDAC Preliminary Technical Data 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 6 NO INTERPOLATION AD9784 INTERP[1] = 0 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 0 8 fSIN INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 0 8 fSIN INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 0 x2 INTERPOLATION x4 INTERPOLATION -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 6 8 fSIN INTERP[1] = 1 INTERP[0] = 1 MOD[0] = 0 8 fSIN 03215-PrD-015 03152-PrD-017 x8 INTERPOLATION MOD[1] = 1 Figure 49. Real Modulation by fDAC/4 under all Interpolation Modes 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 8- -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 NO INTERPOLATION INTERP[1] = 0 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 0 6 8 fSIN INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 0 8 fSIN 6 x4 INTERPOLATION INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 0 8 fSIN 6 x8 INTERPOLATION INTERP[1] = 1 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 0 6 8 fSIN x2 INTERPOLATION Figure 50. Real Modulation by fDAC/8 under all Interpolation Modes Rev. PrC | Page 31 of 52 AD9784 Table 32. Dual Channel Complex Modulation MODSING 0 0 0 0 0 0 0 0 REALIMAG 0 0 0 0 1 1 1 1 MOD[1] 0 0 1 1 0 0 1 1 MOD[0] 0 1 0 1 0 1 0 1 Preliminary Technical Data Mode Real output, no modulation Real output, modulation by fDAC/2 Real output, modulation fDAC/4 Real output, modulation fDAC/8 Image output, no modulation Imag output, modulation by fDAC/2 Imag output, modulation by fDAC/4 Imag output, modulation by fDAC/8 In dual channel mode, the two channels may be modulated by a complex signal, with either the real or imaginary modulation result directed to the DAC. Assume initially that the complex modulating signal is defined for a positive frequency only; this causes the output spectrum to be translated in frequency by the modulation factor only. No additional sidebands are created as a result of the modulation process, and therefore the bandwidth to the first image from the baseband bandwidth is the same as the output of the interpolation filters. Furthermore, pass bands will not overlap or touch. The sinc shaping at the corners of the modulated signal band are tabulated. Figure 52 shows the complex modulations. Table 33. Modulation None fDAC/2 fDAC/4 fDAC/8 None 0 -2.8241 -0.0701 -22.5378 -0.4680 -6.0630 -1.3723 -4.9592 Interpolation x2 x4 0 0 -0.6708 -0.1657 -1.1932 -2.3248 -9.1824 -6.1190 -0.0175 -0.2921 -3.3447 -1.9096 -0.1160 -0.0044 -1.7195 -0.7866 x8 0 -0.0413 -3.0590 -4.9337 -0.5974 -1.3607 -0.0727 -0.4614 Modulated passband edges sinc shaping(lower/upper). FILTERED INTERPOLATION IMAGES -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC 0 fS/8 MODULATION NO NEGATIVE SIDEBAND fDAC 03152-PrD-018 -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC 0 Figure 51. Complex Modulation Rev. PrC | Page 32 of 52 fDAC Preliminary Technical Data 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 x2 INTERPOLATION AD9784 INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 0 MOD[0] = 1 6 8f SIN x4 INTERPOLATION INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 0 MOD[0] = 1 6 8f SIN x8 INTERPOLATION INTERP[1] = 1 INTERP[0] = 1 MOD[1] = 0 MOD[0] = 1 8f 03152-PrD-019 SIN Figure 52. Complex Modulation by fDAC/2 under all Interpolation Modes 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 x2 INTERPOLATION INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 0 6 8 fSIN x4 INTERPOLATION INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 0 6 8 fSIN x8 INTERPOLATION INTERP[1] = 1 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 0 8 fSIN 03152-PrD-020 03152-PrD-021 Figure 53. Complex Modulation by fDAC/4 under all Interpolation Modes 0 -50 -100 -150 -8 0 -50 -100 -150 -8 0 -50 -100 -150 -8 -6 -4 -2 0 2 4 6 -6 -4 -2 0 2 4 -6 -4 -2 0 2 4 x2 INTERPOLATION INTERP[1] = 0 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 1 6 8 fSIN x4 INTERPOLATION INTERP[1] = 1 INTERP[0] = 0 MOD[1] = 1 MOD[0] = 1 6 8 fSIN x8 INTERPOLATION INTERP[1] = 1 INTERP[0] = 1 MOD[1] = 1 MOD[0] = 1 8 fSIN Figure 54. Complex Modulation by fDAC/8 under all Interpolation Modes Rev. PrC | Page 33 of 52 AD9784 POWER DISSIPATION The AD9784 has seven power supply domains: two 3.3 V analog domains (AVDD1 and AVDD2), two 2.5 V analog domains (ADVDD and ACVDD), one 2.5 V clock domain (CLKVDD), and two digital domains (DVDD, which runs from 2.5 V, and DRVDD, which can run from 2.5 V or 3.3 V). The current needed for the 3.3 V analog supplies, AVDD1 and AVDD2, is consistent across speed and varying modes of the AD9784. Nominally, the current for AVDD1 is 29 mA across all speeds and modes, while the current for AVDD2 is 20 mA. The current for the 2.5 V analog supplies and the digital supplies varies depending on speed and mode of operation. Figure 55, Figure 56, and Figure 57 show this variation. Note that CLKVDD, ADVDD, and ACVDD vary with clock speed and interpolation rate, but not with modulation rate. IDVDD (mA) 60 Preliminary Technical Data 50 8x 4x 2x 40 30 1x 20 10 03152-PrD-078 03152-PrD-079 0 0 25 50 75 100 125 150 FDATA (MSPS) 175 200 225 250 Figure 56. CLKVDD Supply Current vs. Clock Speed and Interpolation Rates 03152-PrD-077 425 400 375 350 325 300 275 250 225 200 175 150 125 100 75 50 25 0 0 25 50 30 4x fs/8 8x fs/8 8x fs/4 4x 4x fs/4 2x fs/4 20 2x fs/8 25 8x 4x 2x IDVDD (mA) IDVDD (mA) 8x 2x 15 1x 10 1x 5 0 0 25 50 75 100 125 150 FDATA (MSPS) 175 200 225 250 75 100 125 150 FDATA (MSPS) 175 200 225 250 Figure 55. DVDD Supply Current vs. Clock Speed, Interpolation, and Modulation Rates Figure 57. ADVDD and ACVDD Supply Current vs. Clock Speed and Interpolation Rates Rev. PrC | Page 34 of 52 Preliminary Technical Data FILTERED INTERPOLATION IMAGES AD9784 -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC 0 fS/8 MODULATION -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC 0 fS/4 MODULATION fDAC 03152-PrD-022 -7fDAC/8 -3fDAC/4 -5fDAC/8 -fDAC/2 -3fDAC/8 -fDAC/4 -fDAC/8 fDAC/8 fDAC/4 3fDAC/8 fDAC/2 5fDAC/8 3fDAC/4 7fDAC/8 -fDAC 0 Figure 58. Complex Modulation with Negative Frequency Aliasing DUAL CHANNEL COMPLEX MODULATION WITH HILBERT Table 34. HILBERT 0 1 Mode Hilbert transform off Hilbert transform on When complex modulation is performed, the entire spectrum is translated by the modulation factor. If the resulting modulated spectrum is not mirror symmetric about dc, when the DAC synthesizes the modulated signal, negative frequency components will fall on the positive frequency axis and can cause destructive summation of the signals. For some applications, this can be seen as distorting the modulated output signal. Y = Ae j2(f + fm)t - /2 Im Re A/2 A/2 A/2 A/2 00 A/2 A/2 A/2 f f A Re By performing a second complex modulation with a modulating signal having a fixed /2 phase difference, Figure 59 (Y), relative to the original complex modulation signal, Figure 59 (X), taking the Hilbert transform of the new resulting complex modulation, and subtracting it from the original complex modulation output all negative frequency components can be folded in phase to the positive frequency axis before being synthesized by the DAC. When the DAC synthesizes the modulated output there are no negative frequency components to fold onto the positive frequency axis out of phase; consequently no distortion is produced as a result of the modulation process. 0 ALIASED NEGATIVE FREQUENCY INTERPOLATION IMAGES X = Ae j2(f + fm)t Im Z = HILBERT(Y) Im Re A/2 A/2 A/2 C=X-Z Re Im -50 dBFS A 00 03152-PrD-023 -100 f A/2 A/2 f fDAC fDAC Figure 59. Negative Frequency Image Rejection -150 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 60. Negative Frequency Aliasing Distortion Rev. PrC | Page 35 of 52 03152-PrD-024 AD9784 Figure 60 shows this effect at the DAC output for a mirror asymmetic signal about dc produced by complex modulation without a Hilbert transform. The signal bandwidth was narrowed to show the aliased negative frequency interpolation images. In contrast, Figure 61 shows the same waveform with the Hilbert transform applied. Clearly, the aliased interpolation images are not present. 0 Preliminary Technical Data The transfer function of an ideal Hilbert transform has a +90 phase shift for negative frequencies, and a -90 phase shift for positive frequencies. Because of the discontinuities that occur at 0 Hz and at 0.5 x Sample Rate, any real implementation of the Hilbert Transform trades off bandwidth versus ripple. Figure 62 and Figure 63 show the gain of the Hilbert transform versus frequency. Gain is essentially flat, with a pass-band ripple of 0.1dB over the frequency range 0.07 x Sample Rate to 0.43 x Sample Rate. Figure 64 shows the phase response of the Hilbert transform implemented in the AD9784. The phase response for positive frequencies begins at -90 at 0 Hz, followed by a linear phase response (pure time delay) equal to nine filter taps (nine clock cycles). For negative frequencies, the phase response at 0 Hz is +90, again followed by a linear phase delay of nine filter taps. To compensate for the unwanted 9-cycle delay, an equal delay of nine taps is used in the AD9784 digital signal path opposite to the Hilbert transform. This delay block is noted as t on the data sheet. 10 0 -10 -20 -50 dBFS -100 -150 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 61. Effects of Hilbert Transform If the output of the AD9784 is to be used with a quadrature modulator, negative frequency images are cancelled without the need of a Hilbert transform. 03152-PrD-025 -30 -40 -50 HILBERT TRANSFORM IMPLEMENTATION The Hilbert transform on the AD9784 is implemented as a 19coefficient FIR. The coefficients are given in Table 35 Table 35. Coefficient H(1) H(2) H(3) H(4) H(5) H(6) H(7) H(8) H(9) H(10) H(11) H(12) H(13) H(14) H(15) H(16) H(17) H(18) H(19) Integer Value -6 0 -17 0 -40 0 -91 0 -318 0 318 0 91 0 40 0 17 0 6 Rev. PrC | Page 36 of 52 -60 -70 -80 -90 -100 100 200 300 400 500 600 700 800 900 1000 03152-PrD-074 03152-PrD-075 Figure 62. Hilbert Transform Gain 1.0 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 100 200 300 400 500 600 700 800 900 1000 Figure 63. Hilbert Transform Ripple Preliminary Technical Data 4 3 2 1 0 -1 -2 03152-PrD-076 AD9784 A baseband double sideband signal modulated to IF increases IF filter complexity and reduces power efficiency. If the baseband signal is complex, a single sideband IF modulation can be used, relaxing IF filter complexity and increasing power efficiency. The AD9784 has the ability to place the baseband single sideband complex signal either above the IF frequency or below it. Figure 66 illustrates the baseband selection. -3 -4 100 0 200 400 600 800 1000 1200 Figure 64. Phase Response of Hilbert Transform dBFS -50 Table 36. Dual Channel Complex Modulation Sideband Selection Sideband 0 1 Mode Lower IF sideband rejected Upper IF sideband rejected -100 -150 -0.5 I Re() 0 03151-PrD-003 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 AD9784 Figure 66. Upper IF Sideband Rejected LO 90 0 Q AD9784 Im() Figure 65. AD9784 Driving Quadrature Modulator -50 The AD9784 can be configured to drive a quadrature modulator, representatively as in Figure 65. Where two AD9784s are used with one AD9784 producing the real output, the second AD9784 produces the imaginary output. By configuring the AD9784 as a complex modulator coupled to a quadrature modulator, IF image rejection is possible. The quadrature modulator acts as the real part of a complex modulation producing a double sideband spectrum at the local oscillator (LO) frequency, with mirror symmetry about dc. dBFS -100 -150 -0.5 -0.4 -0.3 -0.2 -0.1 0 0.1 0.2 0.3 0.4 0.5 Figure 67. Lower IF Sideband Rejected Rev. PrC | Page 37 of 52 03152-PrD-028 03152-PrD-027 AD9784 BASEBAND IF Preliminary Technical Data -fIF fIF 0 SIDEBAND = 0 -fIF 0 fIF SIDEBAND = 1 03152-PrD-029 -fIF Figure 68. IF Quadrature Modulation of Real and Complex Baseband Signals Table 37. Data Port Synchronization PLOCKEXT 1 0 0 0 0 0 0 DCLKEXT X 0 0 1 1 1 1 MODSYNC X 0 1 0 0 1 1 DCLKCRC X X X 0 1 0 1 Mode PLL output Dataclk Master Modulator Master Dataclk Slave Dataclk Slave Modulator Slave Modulator Slave Function PLL locked flag output, synchronizer disabled Channel data rate clock output Modulator synchronization clock output Input channel data rate clock, DLL off Input channel data rate clock, DLL on Input modulator synchronizer clock, DLL off Input modulator synchronizer clock, DLL on In applications where two or more AD9784s are used to synthesize several digital data paths, it may be necessary to ensure that the digital inputs to each device are latched synchronously. In complex data processing applications, digital modulator phase alignment may be required between two AD9784s. In order to allow data synchronization and phase alignment, only one AD9784 should be configured as a master device, providing a reference clock for another slave-configured AD9784. With synchronization enabled, a reference clock signal is generated on the DATACLK/PLL_LOCK pin of the master. The DATACLK/PLL_LOCK pins on the slave devices act as inputs for the reference clock generated by the master. The DATACLK/ PLL_LOCK pin on the master and all slaves must be directly connected. All master and slave devices must have the same clock source connected to their respective CLK+/CLK- pins. When configured as a master, the reference clock generated may take one of two forms. In modulator master mode, the reference clock will be a square wave with a period equal to 16 cycles of the DAC update clock. Internal to the AD9784 is a 16-state finite state machine, running at the DAC update rate. This state machine generates all internal and external synchronization clocks and modulator phasings. The rising edge of the master reference clock is time aligned to the internal state machine's state zero. Slave devices use the master's reference clock to synchronize their data latching and align their modulator's phase by aligning their local state machine state zero to the master. The second master mode, DATACLK master mode, generates a reference clock that is at the channel data rate. In this mode, the slave devices align their internal channel data rate clock to the master. If modulator phase alignment is needed, a concurrent serial write to all slave devices is necessary. To achieve this, the CSB pin on all slaves must be connected together and a group serial write to the MODADJ register bits must be performed; the modulator coefficient alignment is updated on the next rising edge of the internal state machine following a successful serial write, Figure 69. Modulator master mode does not need a concurrent serial write as slaves lock to the master phase automatically. In a slave device, the local channel data rate clock and the digital modulator clock are created from the internal state machine. The local channel data rate clock is used by the slave to latch digital input data. At high data rates, the delay inherent in the signal path from master to slave may cause the slave to lag the master when acquiring synchronization. To account for this, an integer number of the DAC update clock cycles may be programmed into the slave device as an offset. The value in DATADJ allows the local channel data rate clock in the slave device to advance by up to eight cycles of the DAC clock or delayed by up to seven cycles, Figure 70. The digital modulator coefficients are updated at the DAC clock rate and decoded in sequential order from the state machine according to Figure 71. The MODADJ bits can be used to align a different coefficient to the finite state machine's zero state as shown in Figure 72. Rev. PrC | Page 38 of 52 fIF 0 Preliminary Technical Data DAC CLOCK STATE MACHINE MODULATOR COEFFICIENT AD9784 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 -1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 -1 0 1 0 MODADJ STATE MACHINE CYCLE CLOCK CHANNEL DATA RATE CLOCK 000 000 Figure 69. Synchronous Serial Modulator Phase Alignment DATADJ[3:0] 0000 1111 0001 DAC CLOCK RECEIVED CHANNEL DATA RATE CLOCK LOCAL CHANNEL DATA RATE CLOCK -1 +1 03152-PrD-031 Figure 70. Local Channel Data Rate Clock Synchronized with Offset STATE DECODE fs/8 fs/4 fs/2 0 1 0 0 0 1 0 2 1/ 2 1 3 0 4 0 2 1 5 0 6 -1/ 2 3 7 0 8 -1 4 2 1 9 0 10 -1/ 2 5 11 0 12 0 6 3 13 0 14 -1/ 2 7 15 0 03152-PrD-032 Figure 71. Digital Modulator State Machine Decode MODADJ[2:0] 000 010 101 DAC CLOCK STATE MACHINE MODULATOR COEFFICIENT STATE MACHINE CYCLE CLOCK 14 15 0 1 2 3 15 0 1 15 0 1 2 -1 0 1 0 -1 0 0 -1 0 1 0 -1 0 03152-PrD-033 Figure 72. Local Modulator Coefficient Synchronized with Offset Rev. PrC | Page 39 of 52 03152-PrD-030 AD9784 OPERATING THE AD9784 REV E EVALUATION BOARD This section helps the user get started with the AD9784 evaluation board. Because it is intended to provide starter information to power up the board and verify correct operation, a description of some of the more advanced modes of operation has been omitted. For a description of the various SPI registers and the effect they have on the operating modes of the AD9784, see the Mode Control (via SPI Port) section. Preliminary Technical Data PECL CLOCK DRIVER The AD9784 system clock is driven from an external source via connector S1. The AD9784 Evaluation Board includes an OnSemiconductor MC100EPT22 PECL clock driver. In the factory, the evaluation board is set to use this PECL driver as a single-ended-to-differential clock receiver. The PECL driver can be set to run from 2.5 V from the CVDIN power connector, or 3.3 V from the VDD3IN power connector. This setting is done via jumper, JP2, situated next to the CVDIN power connector, and by setting input bias resistors R23 and R4 on the evaluation board. The factory default is for the PECL driver to be powered from CVDIN at 2.5 V (R23 = 90.9 , R4 = 115 ). To operate the PECL driver with a 3.3 V supply, R23 must be replaced with a 115 resistor and R4 must be replaced with a 115 resistor, as well as changing the position of JP2. The schematic of the PECL driver section of the evaluation board is shown below in Figure 73. A low jitter sine wave can be used as the clock source. Care must be taken to make sure the clock amplitude does not exceed the power supply rails for the PECL driver. POWER SUPPLIES The AD9784 Rev E Evaluation Board has five power supply connectors, labeled VDDIN, CVDIN, VDD2IN, VDD3IN, and AVDIN. The AD9784 itself actually has seven power supply domains. To reconcile the power supply domains on the chip with the power supply connectors on the evaluation board, use Table 38. Additionally, the DRVDD power supply on the AD9784 is used to supply power for the digital input bus. DRVDD can be run from 2.5 V or 3.3 V. On the evaluation board, DRVDD is jumper selectable by JP1, just to the left of the chip on the evaluation board. With the jumper set to the 3.3 V position, DRVDD chip receives its power from VDD3IN. With the jumper set to the 2.5 V position, DRVDD receives its power from AVDIN. CLKVDDS CLKVDDS CLK+ C32 0.1F ACLKX R23 115 7 MC100EPT22 1 COND;5 U2 CLKVDDS;8 2 R5 50 CLK- Figure 73. PECL Driver on AD9784 Rev E Evaluation Board Table 38. Evaluation Board Label VDDIN CVDIN VDD2IN VDD3IN AVDIN PS Domain on Chip DVDD CLKVDD ACVDD and ADVDD AVDD2 AVDD1 Nominal Power Supply Voltage (V) 2.5 2.5 2.5 3.3 3.3 Description SPI port Clock circuitry Analog circuitry containing clock and digital interface circuitry Switching analog circuitry Analog output circuitry Rev. PrC | Page 40 of 52 03152-PrD-080 R4 90.9 R6 50 R7 50 Preliminary Technical Data DATA INPUTS Digital data inputs to the AD9784 are accessed on the evaluation board through connectors J1 and J2. These are 40 pin right angle connectors that are intended to be used with standard ribbon cable connectors. The input levels should be either 3.3 V or 2.5 V CMOS, depending on the setting of the DRVDD jumper JP1. The data format is selectable through Register 02h, Bit 7 (DATAFMT). With this bit set to a default 0, the AD9784 assumes that the input data is in twos complement format. With this bit set to 1, data should be input in offset binary format. When the evaluation board is first powered up and the clock and data are running, it is recommended that the proper operating current is verified. Depress reset switch SW1 to ensure that the AD9784 is in the default mode. The default mode for the AD9784 is for the internal PLL to be disabled, and the interpolation set to 1x. The modulator is turned off in the default mode. The nominal operating currents for the evaluation board in the power-up default mode are shown in Table 39. Additionally, the DRVDD power supply on the AD9784 is used to supply power for the digital input bus. DRVDD can be run from 2.5 V or 3.3 V. On the evaluation board, DRVDD is jumper selectable by JP1, just to the left of the chip on the evaluation board. With the jumper set to the 3.3 V position, DRVDD chip receives its power from VDD3IN. With the jumper set to the 2.5 V position, DRVDD receives its power from AVDIN. Table 39. Nominal Operating Currents in Power-Up Default Mode Evaluation Board Power Supply VDDIN CVDIN VDD2IN VDD3IN AVDIN 50 MSPS 24 79 1 30 27 Nominal Current @ Speed (mA) 100 MSPS 150 MSPS 49 74 83 87 4 6 30 30 27 27 AD9784 SPI PORT SW1 is a hard reset switch that sets the AD9784 to its default state. It should be used every time the AD9784 power supply is cycled or the clock is interrupted, or if new data is to be written via the SPI port. For a description of the various SPI registers and the effect they have on the operating modes of the AD9784, see the Mode Control (via SPI Port) section. Set the SPI software to read back data from the AD9784 and verify that when the software is run, the expected values are read back. OPERATING WITH PLL DISABLED The SPI registers referenced in this section are shown in Table 40. With the PLL disabled, the evaluation board clock input must be run at the intended DAC sample rate, up to the specified limit of 500 MSPS. At the same time, the interpolation rate should be set so the input data rate does not exceed the 200 MSPS limit. In the default mode with the PLL disabled, the DATACLK signal from the AD9784 is available at connector S2. The rate of this clock is the system clock applied at S1, divided by the interpolation rate. DATACLK can be used to synchronize the external data into the AD9784. 200 MSPS 99 92 8 30 27 Table 40. SPI Registers Register 01h 04h Bit 7 INTERP[1] PLLON Bit 6 INTERP[0] PLLMULT[1] Bit 5 PLLMULT[0] PLL Multiplier Bit 5 0 1 0 1 Bit 4 PLLDIV[1] Bit 3 PLLDIV[0] Bit 0 PLOCKEXT PLL Divider Bit 3 0 1 0 1 Bit 7 0 0 1 1 Interpolation Rate Bit 6 Rate 0 1x 1 2x 0 4x 1 8x Bit 6 0 0 1 1 Mult 2x 4x 8x 16x Bit 4 0 0 1 1 Div /1 /2 /4 /8 Rev. PrC | Page 41 of 52 AD9784 OPERATING WITH PLL ENABLED Note that a specific revision of the AD9784 on the Rev E Evaluation Board has a nonfunctioning PLL. This revision can be identified by the xxx. With the AD9784 PLL enabled, the evaluation board clock input must be run at the data input rate, up to the specified 200 MSPS limit. The PLL controls the internal clock multiplication and drives the interpolation filters and digital modulator. The internal PLL has a VCO in the control loop that is designed to operate optimally over the 200 MHz to 500 MHz range. The VCO speed can be calculated as follows: VCO Speed = Input Data Rate x PLLMULT[1,0] The interpolation rate is set by Bits 6 and 7. With the PLL enabled, the settings for the interpolation rate, the PLL multiplier, and the PLL divide are interrelated. The interpolation rate must meet the following criteria: Interpolation Rate = [Settings of Bits 6, 7] = [PLLMULT / PLLDIVIDER] Therefore, assuming the input data rate is constant and the VCO is at optimal speed, if the interpolation rate is increased by a factor of M, the PLLMULT setting must be decreased by the same factor M. With the PLL enabled, DATACLK connector S2 indicates the lock state of the PLL. A Logic 1 from S2 indicates lock; a Logic 0 indicates the PLL is not currently locked. Preliminary Technical Data ANALOG OUTPUT The analog output of the AD9784 is accessed via connector S3. Once all settings are selected and current levels, PLL lock state, and SPI port functionality are verified, the analog signal at S3 can be viewed. For most of the AD9784's applications, a spectrum analyzer is the instrument of choice to verify proper performance. A typical spectral plot is shown in Figure 74, with the AD9784 synthesizing a two-tone signal in the default mode with a 200 MSPS sample rate. A single tone CW signal should provide output power of approximately +0.5 dBm to the spectrum analyzer. If the spectrum does not look correct at this point, the data input may be violating setup and hold times with respect to the input clock. To correct this, the user should vary the input data timing. If this is not possible, SPI Register 02h, Bit 4 can be inverted. This bit controls the clock edge upon which the data is latched. If these methods do not correct the spectrum, it is unlikely that the issue is timing related. This note should then be reread to verify that all instructions have been followed. 10 0 -10 -20 -30 -40 -50 -60 -60 -70 -80 -90 -100 START 100 kHz 19.9 MHz/ STOP 200 MHz 03152-PrD-081 Figure 74. Typical Spectral Plot Rev. PrC | Page 42 of 52 ADVDD2_IN L8 JP30 ADVDD JP33 ACVDD TP12 FERRITE BLK C75 0.1F CLKVDDS C76 0.1F FERRITE L12 TP1 RED L11 AVD3 SMAEDGE S7 FERRITE + C45 22F 16V C47 0.1F AGND2; 3,4,5 2.5V DVDD_IN L9 JP34 DVDD VDD DVDD AVDD2 ACLKX TP16 BLK JP36 DVDDS DRVDD R4 90.9 7 C48 0.1F TP18 BLK JP1 2 1 3 AB C32 0.1F R23 115 TP13 RED CLK+ Preliminary Technical Data SMAEDGE S5 FERRITE + C46 22F 16V TP17 BLK DGND; 3,4,5 2.5VN MC100EPT22 1 CGND; 5 U2 CLKVDDS; 8 2 R5 50 R7 50 R6 50 CLK- ADVDD3_IN L3 JP9 AVDD2 AVD2 JP1 2 A FERRITE C34 0.1F C29 22F 16V TP3 BLK 1 B CLKVDDS L6 3 C67 0.1F C35 0.1F TP2 RED CLKVDDS + C28 4.7F 6.3V SMAEDGE S9 FERRITE C65 + 22F 16V MC100EPT22 3 6 U2 4 CLKVDDS; 8 CGND; 5 AUX CLOCK AGND2; 3,4,5 3.3V Figure 75. Power Supply Distribution Rev. PrC | Page 43 of 52 L2 JP10 AVDD C68 0.1F TP5 BLK JP7 JP8 JP6 TP4 RED AVD1 FERRITE + C64 22F 16V L1 JP5 C69 0.1F TP7 BLK BLK BLK BLK BLK BLK TP6 RED CVD CLKVDD TP30 TP31 TP32 TP33 TP34 FERRITE C63 + 22F 16V POWER INPUT FILTERS AVDD_IN S10 SMAEDGE 1 2 AGND; 3,4,5 3.3VQ L14 VAL L13 VAL L10 VAL TP36 L7 VAL BLK TP35 BLK CLKVDD_IN SMAEDGE S11 CGND;3,4,5 2.5VQ 03152-PrD-082 AD9784 AD9784 R2 10k AVDD2 CLKVDD CLKVDD C12 0.1F C11 0.1F C49 0.1F DNC2 80 ADVDDP1 79 ADVDD C14 0.1F + C2 10F 6.3V R10 49.9 R9 49.9 ACCOMP1 78 ACVDDP1 77 ACOM2P1 76 AVDD2P1 75 ACOM2P12 74 AVDD1P2 73 ACOM1P11 72 IOUTA 71 IOUTB 70 ACOM1P21 69 AVDD1P1 68 ACOM2P2 67 AVDD2P2 66 ACCOM2P2 65 ACVDDP2 64 ADCOMP2 63 ADVDDP2 62 DNC1 61 FSADJ 60 REFIO 59 RESET 58 SPI_CSB 57 SP-CLK 56 SP-SDI 55 SP-SDO 54 DCOM6 53 DVDD6 52 P2B0LSB 51 P2B1 50 31 DCLK-PLLL 32 P2B15MSB-IQSEL 33 P2B14-OPCLK R3 10k AVDD C62 0.1F C4 0.1F C18 0.001F C61 0.001F C13 0.1F T2A JP22 1 2 3 4 CLKCOM1 5 CLK+ 6 CLK- 7 CLKCOM2 2 LPF 1 CLKVDD1 TP15 WHT +C1 10F 6.3V C42 0.1F C20 0.001F C55 0.001F C49 1pF 6 R1 50 JP23 C19 0.1F 3 CLKVDD2 5 4 T1 T1-1T ACLKX CLK- DVDD 8 DCOM1 9 DVDD1 S1 CGND; 3,4,5 CLK+ 3 P + ACVDD C17 0.1F + C15 0.1F + C10 10F 6.3V C26 0.001F AD14 AD13 AD12 AD11 AD10 DVDD 17 DVDD2 16 DCOM2 15 P1B10 14 P1B11 13 P1B12 12 P1B13 11 P1B14 C40 0.1F C66 10F 6.3V AD15 10 P1B15MSB 1 T3 S 4 6 3 2 1 6 T2A NC = 5 4 AGND; 3,4,5 S3 OUT1 R42 49.9 DRVDD + C31 10F 6.3V C54 0.001F AD08 AD07 AD06 AD05 AD04 AD03 DVDD 26 DVDD3 25 DCOM3 24 P1B3 23 P1B4 22 P1B5 21 P1B6 20 P1B7 19 P1B8 C33 0.1F C25 0.001F TP11 WHT C41 0.1F + C9 10F 6.3V AD09 18 P1B9 ADTL1-12 C3 10F 6.3V S P TC1-1T T2B NC = 5 TP8 WHT TP10 WHT 4 5 Figure 76. Local Circuitry Rev. PrC | Page 44 of 52 RESET SPCSB SPCLK SPSDI SPSDO S2 C24 0.001F AD01 AD00 28 P1B1 29 P1B0LSB 30 DRVDD1 3 + C30 10V 10F R8 C16 2.000k 0.1F 0.01% 6 S P 1 TTWB-1-B TP14 WHT + C8 10F 6.3V C39 0.1F AD02 27 P1B2 AGND; 3,4,5 S3 TP29 BLK DVDD BD00 BD01 P2B2 49 P2B3 48 BD02 BD03 C38 0.1F C21 0.001F + C5 10F 6.3V DGND; 3,4,5 DATACLK BD15 BD14 BD13 DVDD JP27 BD12 C36 0.1F BD11 BD10 BD09 OPCLK 3 JP28 2 A B 34 P2B13 35 DCOM4 36 DVDD4 37 P2B12 38 P2B11 39 P2B10 40 P2B9 P2B4 47 P2B5 46 DCOM5 45 DVDD5 44 P2B6 43 P2B7 42 U1 P2B8 41 BD04 BD05 RESET BD06 BD07 BD08 C37 0.1F 4 3 C22 0.001F DVDD + C6 10F 6.3V SW1 2 1 FLOAT; 5 DRVDD OPCLK_3 1 S6 S4 OPCLK + C7 10F 6.3V C23 0.001F IQ DGND; 3,4,5 Preliminary Technical Data 03152-PrD-083 AD9786BTSP Preliminary Technical Data AX15 R26 100 R30 100 R31 100 R32 100 R33 100 AX08 AD9784 AX14 R27 100 R28 100 R29 100 AX09 JP3 AX10 JP12 AX11 AX13 AX12 RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 2 3 4 5 6 7 8 9 10 RP5 DNP RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 2 3 4 5 6 7 8 9 10 RP7 DNP DATA-A 1 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 AX15 AX14 AX13 AX12 AX11 AX10 AX09 AX08 AX07 AX06 AX05 AX04 AX03 AX02 AX01 AX00 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 RP1 22 RP1 22 RP1 22 RP1 22 RP1 22 RP1 22 RP1 22 RP1 22 RP2 22 RP2 22 RP2 22 RP2 22 RP2 22 RP2 22 RP2 22 RP2 22 16 15 14 13 12 11 10 9 16 15 14 13 12 11 10 9 AD15 AD14 AD13 AD12 AD11 AD10 AD09 AD08 AD07 AD06 AD05 AD04 AD03 AD02 AD01 AD00 39 RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 AX00 RCOM 37 1 2 3 4 5 6 7 8 9 10 RP6 DNP 1 2 3 4 5 6 7 8 9 10 RP8 DNP R1 R2 R3 R4 R5 R6 R7 R8 R9 RIBBON J1 AX07 R38 100 AX06 R39 100 R40 100 R34 100 R44 100 R43 100 R41 100 R46 100 AX01 JP21 JP19 AX02 AX05 AX04 Figure 77. Digital Data Port A Input Terminations Rev. PrC | Page 45 of 52 03152-PrD-084 AX03 AD9784 BX15 R62 100 R57 100 R58 100 R59 100 R63 100 BX08 Preliminary Technical Data BX14 R61 100 R60 100 R64 100 BX09 JP26 BX10 JP31 BX11 BX13 BX12 RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 2 3 4 5 6 7 8 9 RP12 10 DNP RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 2 3 4 5 6 7 8 9 10 RP9 DNP DATA-B 1 1 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 BX15 BX14 BX13 BX12 BX11 BX10 BX09 BX08 BX07 BX06 BX05 BX04 BX03 BX02 BX01 BX00 SDO CLK 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 RP3 22 RP3 22 RP3 22 RP3 22 RP3 22 RP3 22 RP3 22 RP3 22 RP4 22 RP4 22 RP4 22 RP4 22 RP4 22 RP4 22 RP4 22 RP4 22 16 15 14 13 12 11 10 9 16 15 14 13 12 11 10 9 BD15 BD14 BD13 BD12 BD11 BD10 BD09 BD08 BD07 BD06 BD05 BD04 BD03 BD02 BD01 BD00 CSB RCOM R1 R2 R3 R4 R5 R6 R7 R8 R9 BX00 RCOM SDI 1 2 3 4 5 6 7 8 9 10 RP11 DNP 1 2 3 4 5 6 7 8 9 10 RP10 DNP R1 R2 R3 R4 R5 R6 R7 R8 R9 RIBBON J2 BX07 R55 100 BX06 R54 100 R53 100 R56 100 R51 100 R49 100 R47 100 R52 100 BX01 JP25 JP24 BX02 BX05 BX04 Figure 78. Digital Data Port B Input Terminations Rev. PrC | Page 46 of 52 03152-PrD-085 BX03 Preliminary Technical Data DVDDS 4 PRE + C52 4.7F 6.3V C53 0.1F AD9784 OPCLK 6 Q_ CLR 15 DGND;8 74LCX112 DVDDS;16 U7 3 J 1 CLK 2 K Q 5 OPCLK_3 SDO SDI 10 PRE 11 9 J Q 13 CLK 12 7 K Q_ CLR 14 74LCX112 DGND;8 U7 DVDDS;16 U5 U5 CLK CSB SW2 A 3 2 B1 R50 9k R48 9k R45 9k 2 B1 SW3 A 3 2 B1 SW4 A 3 2 B1 SPI PORT P1 1 2 3 4 5 6 SW5 A 3 SPCSB 2 1 12 13 74AC14 SPCLK 4 U5 3 74AC14 10 U5 11 74AC14 SPSDI 6 U5 5 74AC14 8 U5 9 74AC14 SPSDO 1 U6 2 74AC14 13 U6 12 DVDDS 74AC14 R21 10k R20 10k 3 U6 4 11 74AC14 U6 10 74AC14 5 U6 6 9 74AC14 U6 8 74AC14 74AC14 Figure 79. SPI and One-Port Clock Circuitry Rev. PrC | Page 47 of 52 03152-PrD-086 + C43 4.7F 6.3V C50 0.1F + C44 4.7F 6.3V C51 0.1F AD9784 Preliminary Technical Data Figure 80. PCB Assembly, Primary Side 03152-PrD-087 Figure 81. PCB Assembly, Secondary Side Rev. PrC | Page 48 of 52 03152-PrD-088 Preliminary Technical Data AD9784 Figure 82. PCB Assembly, Layer 1 Metal Figure 83. PCB Assembly, Layer 6 Metal Rev. PrC | Page 49 of 52 03152-PrD-090 03152-PrD-089 AD9784 Preliminary Technical Data Figure 84. PCB Assembly, Layer 2 Metal (Ground Plane) Figure 85. PCB Assembly, Layer 3 Metal (Power Plane) Rev. PrC | Page 50 of 52 03152-PrD-092 03152-PrD-091 Preliminary Technical Data AD9784 Figure 86. PCB Assembly, Layer 4 Metal (Power Plane) Figure 87. PCB Assembly, Layer 5 Metal (Ground Plane) Rev. PrC | Page 51 of 52 03152-PrD-094 03152-PrD-093 AD9784 OUTLINE DIMENSIONS 0.75 0.60 0.45 SEATING PLANE 1.20 MAX 80 1 Preliminary Technical Data 14.00 SQ 12.00 SQ 61 60 60 61 80 1 PIN 1 TOP VIEW (PINS DOWN) BOTTOM VIEW 6.00 SQ 20 21 40 41 41 40 21 20 0.15 0.05 1.05 1.00 0.95 0.20 0.09 COPLANARITY 0.08 0.50 BSC 0.27 0.22 0.17 7 3.5 0 GAGE PLANE 0.25 COMPLIANT TO JEDEC STANDARDS MS-026-ADD-HD Figure 88. 80-Lead Thermally Enhanced TQFP (SV-80) Dimensions shown in millimeters) ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. (c) 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. PR03151-0-3/04(PrC) Rev. PrC | Page 52 of 52 |
Price & Availability of AD9784 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |