View SLWU003C_1003768.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLV320AIC10/11 EVM
User's Guide
July 2000
AAP Data Converter Group
SLWU003C
IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Customers are responsible for their applications using TI components. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof.
Copyright (c) 2000, Texas Instruments Incorporated
How to Use This Manual
Preface
Read This First
About This Manual
This document presents a description of the TLV320AIC10/11 EVM.
How to Use This Manual
This document contains the following chapters:
- Chapter 1 - Introduction - Chapter 2 - Analog Interface - Chapter 3 - Digital Interface - Chapter 4 - Software Driver - Chapter 5 - PC Board and Bill of Materials - Appendix A - Schematics
Read This First
iii
Running Title--Attribute Reference
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Analog Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Single-Ended to Differential Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 DAA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Microphone Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Speaker Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Digital Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1 Master/Slave Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 C5402 DSK McBSP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Master Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 Frame Sync Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7......AIC10/11EVMJumperPositionSetup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . 2-1 2-2 2-2 2-2 2-2 2-3 3-1 3-2 3-2 3-2 3-2 3-2 3-3 3-4
2
3
4
Software Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 4.1 AIC10-EVM Test Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 4.2 TLV320AIC10/11 Plug-In for Code Composer Studio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 PC Board and Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 5.1 Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.2 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
5
A
Chapter Title--Attribute Reference
v
Running Title--Attribute Reference
Figures
1-1 2-1 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Microphone Interface With TLV320AIC10/11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board (Top) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board (Bottom) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printed-Circuit Board Layer 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2-2 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9
vi
Chapter 1
Introduction
The TLV320AIC10/11 EVM is designed to be a daughterboard that plugs directly into the peripheral connector of the TMS320VC5402 DSK board. For more information about the C5402 DSK, go to http://www.ti.com/sc/docs/tools/dsp/tmdx320005402.htm. The AIC10/ 11-EVM is populated with two TLV320AIC10/11 devices and has footprints for six more to provide full capability of cascading eight TLV320AIC10/11s (one master and seven slaves) to one single DSP's McBSP. The two populated TLV320AIC10/11s (U1 and U2) can be configured as either two separate masters (or slaves) to connect to two McBSPs, or as a master/slave cascade to connect to one McBSP. For analog input/output, U1 is interfaced with DAA, normal analog input, and speaker, and U2 is interfaced with microphone, normal analog input, and speaker. The EVM is powered by either a 3.3-V or a 5-V power supply. For more information about the C5402 DSK, go to http://www.ti.com/sc/docs/ tools/dsp/tmdx320005402.htm
Topic
1.1
Page
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Introduction
1-1
System Block Diagram
1.1 System Block Diagram
The TLV320AIC10/11 EVM provides a practical platform for evaluating the TLV320AIC10/11 voiceband codec. The system block diagram is shown in Figure 1-1. This illustration provides a general idea of the system configuration. It is not meant to replace the circuit diagram, but to give a brief indication of the features and functions available. It should be read in combination with the circuit diagram supplied.
Figure 1-1. Block Diagram
J10 J7 J1 J5 Analog Input AIC10/11 DAA Speaker Driver Analog Input Microphone Input Speaker Driver AIC10/11 AIC10/11 AIC10/11 AIC10/11 w C54xx DSK AIC10/11 AIC10/11 AIC10/11
Crystal
J8 J12 J6
J2
DVDD 3.3 V-5 V DGND DVDD 1.1 V (AIC11 Only) DGND
J3
AVDD 3.3 V-5 V AGND 5VS AGND
J9
J3
1-2
Chapter 2
Analog Interface
This chapter presents the system analog interface.
Topic
2.1 2.2 2.3 2.4 2.5
Page
Single-Ended-to-Differential Converter . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 DAA Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Microphone Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Speaker Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Analog Interface
2-1
Single-Ended to Differential Converter
2.1 Single-Ended to Differential Converter
There are two single-ended-to-differential converter circuits on the AIC10/11-EVM board connected through J7 and J8. These circuits provide differential analog signals to the INP/INM input of U1 and the AURXP and AURXM inputs to U2. The design of these converters uses the TI TLV2462 (U12, U13), a low-power rail-to-rail input/output operational amplifier designed for single-supply portable applications.
2.2 DAA Interface
By setting the jumpers W2, W3, W35, and W36, the codec U1 can be connected to interface with the DAA U11 for communication with the PSTN. The phone line is plugged to J1. The TLV320AIC10/11 controls the DAA's OH (offhook) and RING (ring detection) by programming the ALTIN and FLAG pins. The operational amplifier (U18) is low-voltage logic translation that provides the logic level to be used by the OH and CIO pins of the DAA.
2.3 Microphone Interface
The user can program the codec U2s built-in MIC preamp to interface the TLV320AIC10/11 with a microphone plugged to J12. The common mode of this on-chip preamp is referenced by VMID that also is used to bias the microphone.
Figure 2-1. Microphone Interface With TLV320AIC10/11
AURXFP 0.1 F 10 k 10 k AURXM AURXCP - +
S2D
TLV320AIC10
Electret Microphone
20 k 1 k MIC_BIAS VMID
AntiAliasing Filter
PGA
SigmaDelta ADC
Vref
Microphone Interface
2.4 Speaker Interface
The U1 and U2 codecs can be configured to interface to the speaker drivers. The speaker driver is a TI TPA4861 audio power amplifier capable of delivering 1 W of continuous average power into an 8- load. Two jumpers, W2 and W3, select between the DAA transmitter and the speaker driver U9 as the U1's differential output load. Jumpers W39 and W60 connects the analog output of U2 to the speaker driver U10. External speakers are connected to J5 and J6.
2-2
Power Supply
2.5 Power Supply
The AIC10/11-EVM requires 3 separate external power supplies. The 5-V to 3.3-V supply from J2 is used for the digital circuits on the board. The AIC11 requires 1.8 V digital supply for its digital I/O, which comes from J9 instead of J2, and the jumper W61 to short pins 1 and 2. The 5-V supply from J4 is used for the DAA and speaker drivers. The 5-V to 3.3-V supply from J3 is used for all analog circuits.
Analog Interface
2-3
Chapter 3
Digital Interface
This chapter describes the TLV320AIC10/11-EVM's digital interface.
Topic
3.1 3.2 3.3 3.4 3.5 3.6 3.7
Page
Master/Slave Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 C5402 DSK McBSP Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Host Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Master Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Frame Sync Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 AIC10/11-EVM Jumper Position Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Digital Interface
3-1
Master/Slave Selection
3.1 Master/Slave Selection
Both U1 and U2 codecs can be individually configured to function as either a master or a slave by selecting the proper jumper position on W1 and W11.
3.2 C5402 DSK McBSP Interface
The codec U1 is designed to gluelessly connect to the C5402's McBSP0 via the common connector on the C5402 DSK board. Jumpers W13, W15, W16, and W17 are intended to connect U2 to the same McBSP0 as a slave of U1, or to the McBPS1 as a separate master/slave.
3.3 Host Interface
The host interface on the AIC10/11-EVM is primarily designed for the master/ slave cascade configuration. In this configuration the DCSI (direct configuration) uses jumper W20 to select the serial data input source from either the DSK's McBSP1 or from an external source.
3.4 Master Clock
The AIC10/11-EVM contains an onboard crystal that generates a clock frequency of 8.2 MHz. Jumper W14 selects the master clock source for all TLV320AIC10/11 devices from either the onboard crystal, or from an external source (such as the CLOCKOUT from C5402).
3.5 Frame Sync Mode
Input pins M0 and M1 select frame sync modes, as described in section 2.8 of the TLV320AIC10/11 data manual. Jumpers W4 and W5 configure M0 and M1 of codec U1, respectively. Jumpers W9 and W10 configure M0 and M1 of codec U2, respectively.
3.6 LED
The two LEDs of D2 and D3 are controlled by the FLAG pins on two AIC10/11 of U1 and U2 which are programmed by the software driver to make LEDs flash. This indicates good communication between the AIC10/11 and the DSP.
3-2
AIC10/11-EVM Jumper Position Setup
3.7 AIC10/11-EVM Jumper Position Setup
Jumper W1 W2 W3 W4 W5 W6 W7 W9 W10 W11 W12 W13 Position 1 * * * Vdd Vdd * * Vdd Vdd * * * * W14 W15 * * * W16 W17 W18 W19 W20 W21 W22 W35 W36 W37 W38 W39 W60 W61 W40 W41 * * * * * * * * * * * * * * * * 2 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * GND GND * * GND GND * * 3 Set U1 as a master codec Set U1 as a slave codec Connect OUTP of U1 to TX+ of U11 Connect OUTP of U1 to IN+ of U9 (speaker driver) Connect OUTM of U1 to TX- of U11 Connect OUTM of U1 to IN- of U9 (speaker driver) These two pins are used to set frame sync mode (M0, M1) of U1 (set both jumpers to y ( ) ( j position 2-3 to work with C54xx driver) Use external supply via J2 for DVDD (digital supply) Use C54xx DSK supply for DVDD (digital supply) Use external supply via J3 for AVDD (analog supply) Use C54xx DSK supply for AVDD (analog supply) These two pins are used to set frame sync mode (M0, M1) of U2 (set both jumpers to y ( ) ( j position 2-3 to work with C54xx SW driver) Set U2 as a master codec Set U2 as a slave codec To connect to the input CID of U11 Connect FS of U2 to FSX of C54x's McBSP1 Connect FS of U2 to FSD of U1 (U1 = master, U2 = slave) Short all 3 positions together for using DCSI with C54 SW driver Connect MS_CLOCK on the EVM to C54 DSK's CLKOUT Connect MS_CLOCK on the EVM to onboard oscillator U16 Connect SCLK of U2 to C54 McBSP1's CLKX Connect SCLK of U2 to C54 McBSP0's CLKX Short all 3 positions together for using DCSI with C54 SW driver Connect DIN of U2 to C54 McBSP1's DX Connect DIN of U2 to C54 McBSP0's DX Connect DOUT of U2 to C54 McBSP1's DR Connect DOUT of U2 to C54 McBSP0's DR Connect DVDB of AIC10EVM to motherboard's 5-V supply Connect DVDB of AIC10EVM to motherboard's 3.3-V supply Connect AVDB of AIC10EVM to motherboard's 5-V supply Connect AVDB of AIC10EVM to motherboard's 3.3-V supply Use C54 McBSP1's DX to send data to DCSI of both U1 and U2 For C54 DSK motherboard to detect AIC10EVM To power down the AIC10 on the EVM To connect RX+ and RX_ of U11 to INP and INM of U1, respectively RX U1 To connect the output of op amp input buffer to INP and INM of U2 op-amp To connect OUTP and OUTM of U2 to IN+ and IN- of U10 (speaker driver) IN To connect DVDD1 to 1.8-V external supply J9 To connect DVDD1 to 3.3-V/5-V external supply J2 To disable FC pin of U1 To disable FC pin of U2 Description
Digital Interface
3-3
Interface Signals
3.7.1
Default Jumper Positions of AIC10/11-EVM
W3 1-2 W11 2-3 W22 2-3 W36 SHORT W4 2-3 W16 2-3 W60 SHORT W35 SHORT W12 1-2 W5 2-3 W17 2-3 W39 SHORT W13 1-2-3 W40 SHORT W1 1-2 W14 2-3 W38 SHORT W15 1-2-3 W41 SHORT W9 2-3 W6 1-2 W37 SHORT W20 1-2-3 W61 2-3
W2 1-2 W10 2-3 W7 1-2 W21 SHORT
All other jumpers are open.
3.8 Interface Signals
The following table shows the AIC10/11-EVM interface signals.
Pin Number 21 23 24 27 29 30 33 35 36 39 41 42 Pin Name X_CLKX0 X_FSX0 X_DX0 X_CLKR0 X_FSR0 X_DR0 X_CLKX1 X_FSX1 X_DX1 X_CLKR1 X_FSR1 X_DR1 I/O/Z I/O I/O I I/O I/O O/Z I/O I/O I I/O I/O O/Z DSP McBSPx 0 0 0 0 0 0 1 1 1 1 1 1 Description Transmit clock Transmit frame sync Transmit serial data Receive clock Receive frame sync Receive serial data Transmit clock Transmit frame sync Transmit serial data Receive clock Receive frame sync Receive serial data
Note: Other signals are coming from the DSP and are not used by the AIC10/11-EVM
3-4
Chapter 4
Software Driver
There are two AIC10/11 software versions available for downloading from the TLV320AIC10/11 development tool web site. AIC10-EVM test software and CCS software driver plug-in AIC10/11-EVM test software. (The software drivers can be downloaded from https://www-a.ti.com/apps/dc_plugins/aic10/11_register.asp)
Topic
4.1 4.2
Page
AIC10-EVM Test Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 TLV320AIC10/11 Plug-In for Code Composer Studio . . . . . . . . . . . . . 4-3
Software Driver
4-1
AIC10-EVM Test Software
4.1 AIC10-EVM Test Software
Software drivers aic10sw_m and aic10sw_ms contain code for a single master codec and a master/slave cascade, respectively. The following C54xx software subroutines are included. They have been tested with the TI code composer, and they demonstrate how to program the C54xx DSK to control a cascade of master U1 and slave U2 on the AIC10/11-EVM.
- AIC10_DTMF.C
This C-code serves as the main program and generates DTMF for phone number 972-480-1094 based on a sampling rate of 16 KSPS. It also contains two ISRs (interrupt service routines) for McBSP0 and McBSP1 in which McBSP0 services the master/slave cascading of the two TLV320AIC10/11s on the board, and McBSP1 programs both U1 and U2's FLAG pins using DCSI via jumper W20 to make the two LED D1 and D2 flash.
- C5402VEC.ASM
This code defines the vector table for C54xx software.
- DCSI_COMM.ASM
This code controls McBSP1 data transfer for TLV320AIC10/11's direct configuration (DCSI).
- INIT5402.ASM
This code initializes the C5402 registers.
- MCBSP.ASM
This code initializes the C5402's McBSP registers.
- INITAIC10.ASM
This code detects master and slave codecs and initializes their four control registers:
J J J
Set sampling rate at 16 KSPS. Turn on OFF-HOOK for DAA interface with the master codec. Enable the MIC preamp to receive input from the microphone.
- MS_COMM.ASM
This code controls McBSP0 data transfer to/from the master TLV320AIC10/11 codec.
- SL_COMM.ASM
This code controls McBSP0 TLV320AIC10/11 codec.
data
transfer
to/from
the
slave
4-2
TLV320AIC10/11 Plug-In for Code Composer Studio
4.2 TLV320AIC10/11 Plug-In for Code Composer Studio
There are two examples for the AIC10/11 in this zip-file:
- Dial tone - Sample
Dial tone demonstrates the write-block function of the AIC10/11 driver. It generates a sequence of dial tones based on a telephone number and puts it out on the master output. Sample demonstrates the read-block function of the AIC10/11 driver. It reads a block of samples from the master and slave AIC10/11 and stores it in the DSP memory. Unzip the file to the original folders and load the project file (AIC10/11_CCS.mak for both examples). Dial Tone:
- Hook up a speaker to the master speaker port. - Load the program to the DSP DSK and start it with F5.
Sample:
- Set a breakpoint at the dc_rblock function (line 38), load the program to
the DSK and start the program with F5.
- After each cycle (F5), the data contains the samples from the AIC10/11
chain.
- Open a graph window to see the samples as a wave-form.
Note: These subroutines have been tested using the C54xx C/ASM compiler Ver 3.1. If a different compiler version is used, the user may have to adjust the pipeline delay (that is, NOP) associated with McBSP code to meet the McBSP timing requirement. The DSK is bundled with a special version of Code Composer Studio, allowing new designers to experiment with code composer features like real-time analysis and data visualization. Code Composer Studio's unrivaled feature set makes DSP development easy. The DSK's special 32-K object code generation tool set allows users to experiment with sample code, test algorithms, and write their own application. Users have the flexibility of writing their application in C, making getting started easier than ever before. For more information about the C5402 DSK, go to http://www.ti.com/sc/docs/ tools/dsp/tmdx320005402.htm New Code Composer Studio Free Evaluation Tools (FETs) from TI are a full featured, full-function 30-day time-limited version of the C5000 DSPs software development tools, and are now available for download at http://www.ti.com/ sc/docs/tools/dsp/5ccsfreetool.htm
Software Driver
4-3
Chapter 5
PC Board and Bill of Materials
This chapter presents and introduction to the power supplies used with the AIC10/11-EVM, and a listing of the parts required to build this evaluation module.
Topic
5.1 5.2
Page
Printed-Circuit Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
PC Board and Bill of Materials
5-1
Printed-Circuit Board
5.1 Printed-Circuit Board
This section presents the printed-circuit board for the TLV230AIC10/11 EVM.
Figure 5-1. Printed-Circuit Board (Top)
5-2
Printed-Circuit Board
Figure 5-2. Printed-Circuit Board (Bottom)
PC Board and Bill of Materials
5-3
Printed-Circuit Board
Figure 5-3. Printed-Circuit Board Layer 1
5-4
Printed-Circuit Board
Figure 5-4. Printed-Circuit Board Layer 2
PC Board and Bill of Materials
5-5
Printed-Circuit Board
Figure 5-5. Printed-Circuit Board Layer 3
5-6
Printed-Circuit Board
Figure 5-6. Printed-Circuit Board Layer 4
PC Board and Bill of Materials
5-7
Printed-Circuit Board
Figure 5-7. Printed-Circuit Board Layer 5
5-8
Printed-Circuit Board
Figure 5-8. Printed-Circuit Board Layer 6
PC Board and Bill of Materials
5-9
Bill of Materials
5.2 Bill of Materials
Ref Des
B1
Used Part Type
1 SMT_BRIDGE
Footprint
SAI_F27_1N
Description
SHINDENGEN S1NB60 or Digikey DF06SGICT-ND Ceramic multilayer capacitor
Population Status
C1 C100 C102 C104 C2 C20 C21 C23 C24 C3 C4 C5 C6 C76 C77 C78 C79 C80 C81 C82 C83 C84 C85 C86 C87 C88 C89 C90 C91 C92 C93 C94 C95 C96 C9 C98 C99 C10 C11 C8 C9 C12 C13 C15 C19 C22 C29 C30 C31 C32 C33 C34 C35 C36 C27 C38 C39 C40 C41 C42 C43 C44 C45 C46 C47 C48 C68 C69 C70 C14 C18 C16 C17 C25 C49 C50 C51 C52 C53 C54 C56 C57 C58 C59 C60 C61 C62 C63 C64 C65 C66 C67 C71 C72 C73 C74 C75 C27 C28 C7 D1 D2 D3 F1
36
0.1 F
0805
4 28
220 pF 2KV 1 F
1808 1260
NOVACAP SP1808B221M202N Ceramic multilayer capacitor
2 1 25
560 pF 4.7 nF 10 F
0805 0805 3528
Ceramic multilayer capacitor Ceramic multilayer capacitor
1 1 1 1 1 1 1
0.01 F 0.47 F 0.001 F 500 V P3100SB LED red LED green FUSE
0805 0805 1206 DO-214 1206 1206 3216-CHIP (1206) 154-UL6663 TFM-140
Ceramic multilayer capacitor Ceramic multilayer capacitor NOVACAP 1206B102K501N TECCOR (Mouser 5191-P3100SA) Digikey L62201CT-ND Digikey L62205CT-ND WICKMANN 4431100000 1A 63 V Digikey WK4661CT-ND Mouser RJ12 phone jack -PN 154-UL6663 TFM-140-31-S-D J15 TFM used for mechanical support
J1 J10 J15
1 1
RJ12 TFM-140
J12 J7 J8 J13 J14 J2 J3 J4 J5 J6 J9
3 2 6
PHONO_JACK 12X3X.1 CON_2TERM_ SCREW
161-3504 12X3X.1 2term_screw_con
PCB mount phone jack Mourser 161-3504 36 pin header for PCB interconnect 2 terminal screw connector DO NOT POPULATE
5-10
Bill of Materials
Population Status
Ref Des
L1 L2 L3 L4 L5 L6 Q1 R1 R10 R107 R108 R111 R111 R13 R17 R18 R19 R20 R21 R22 R23 R24 R25 R26 R27 R28 R29 R30 R31 R32 R33 R34 R35 R36 R37 R38 R39 R40 R41 R42 R43 R44 R45 R46 R47 R48 R49 R50 R51 R42 R53 R54 R55 R56 R57 R58 R59 R6 R60 R61 R62 R8 R9 R100 R101 R102 R74 R77 R93 R94 R95 R96 R99 R103 R12 R104 R105 R106 R16 R69 R7 R75 R2 R3 R4 R5 R63 R97 R110 R64 R14 R15 R65 R66 R67 R68 R70 R71 R72 R73 R74 R78 R76 R98 R109 RP1 R79 R80 R81 R82 R83 R84 R85 R86 R87 R88 R89 R90 R91 R92 SW1 SW2
Used Part Type
4 2 1 1 55 BEAD 4.7 H CPC5602C 200K 10K
Footprint
1806 DO1608C 4-SOT223 805 805
Description
Taiyo Yuden FBMJ4516HM111N DO1608C-Series - Coil Craft N-Channel FET, 4 pin SOT-223 RES, SMD, 0805 RES, SMD, 0805
10 2 1 2 4 1 2 1 1 2 1 12 3 1 4 1 1 1 2 1 1 1 2 1 1
20K 1 0 10 44K 604K 1% 150K 10M 10M, 1/4W 11K 1.2M 22K 1K 1K 470 8.2 300 604 1% 806K 1% 402 1% 100 1M 1.5M SW-PB SW 12 POS
805 805 805 1206 805 805 805 805 1206 805 805 805 805 TRIM POT 805 805 805 805 805 805 805 0805 0805 EVQ-PJ X-435640-X
RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 1206 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 1206 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 3214W-1-102E RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 RES, SMD, 0805 Panasonic EVQ-PJS05K Dip switch, AMP 7100 series, 12 pos
PC Board and Bill of Materials
5-11
Bill of Materials
Population Status
Ref Des
TP1 TP2 TP10 TP11 TP12 TP13 TP2 TP3 TP4 TP5 TP6 TP7 TP8 TP9 U1 U2 U3 U4 U5 U6 U7 U8
Used Part Type
13 TP_0.025
Footprint
test_point2
Description
SAMTEC TWS-101-07-L-S 0.025" pin TLV320AIC10
8
TLV320AIC10
48-TQFP (PFB)
DO NOT POPULATE U3-U8
U10 U9 U11 U12 U13 U18 U14 U15 U16
2 1 3 1 1 1
TPA4861D CPC5604 TLV2462D SN74HC02 TPS3823 EPSON 8.200 MHz SN74HC74 SN84HC08 2POS_JUMPER
8-SOP (D) 32_SOIC 8-SOP(D) 14-SOP (D) 5-SOT (DBV) 4PIN_XTL_DC
TPA4861 CPC5604 TLV2462A Quad 2 input pos OR TPS3823 EPSON SG-8002DC-SCC8.200 MHZ Dual D PET FF RS CR Quad NAND gate SAMTEC TSW-102-07-L-S 0.1" spacing DO NOT POPULATE W42-W50 W51-W59
U17 U19 W21 W35 W36 W37 W38 W39 W40 W41 W42 W43 W44 W45 W46 W47 W48 W49 W50 W51 W52 W53 W54 W55 W56 W57 W58 W59 W60 W8 W62
1 1 29
14-SOP (D) 14-SOP (D) 2 pos_jump
Jumper Hook Up Table TLV320AIC10 W3 1-2 W11 2-3 W22 2-3 W36 SHORT W9 2-3 W6 1-2 W37 SHORT W20 1-2-3 W13 1-2-3 W5 1-2 W17 2-3 W39 SHORT W41 SHORT W61 2-3 Jumper Hook Up table TLV320AIC11 W61 1-2 2 pos short SAMTEC SNT-100-BK-T or equivalent W4 1-2 W16 2-3 W60 SHORT W35 SHORT W40 SHORT W2 1-2 W10 2-3 W7 1-2 W21 SHORT W1 1-2 W14 2-3 W38 SHORT W15 1-2-3 2 pos short 2 pos short 2 pos short 2 pos short 2 pos short 2 pos short 2 pos short 3 pos short 3 pos short 2 pos short 2 pos short 2 pos short 2 pos short 2 pos short SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent S.V.Tronics 70-0000-3 S.V.Tronics 70-0000-3 SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent SAMTEC SNT-100-BK-T or equivalent
5-12
Appendix A
Schematics
This Appendix contains the TLV320AIC10/11 EVM schematics.
Schematics
A-1
1
2
3
4
5
REV
6 Revision History
ECN Number Approved
C6
CID R110 11K R14 22K D OH R97 11K 3 7 6 TLV2462 CIDI 5VS
R5
10M
C7
0.001uF 500V 3
U11 R2
TP10
32 31 30 29 28 27 26 25
0.1uF
B1
+ AC AC 1 2 2 CIDI
U18B
5
U18A
1 2 TLV2462 OHI
604K 1% 1 Vcc TXF1 TXTX+ TX NC GND OH RING CID RXRX+ SNP+ SNPRXF RX CPC5604 BRTXF2 ZTX ZNT TXS BRNTS GAT REF DCS DCF ZDC BRRPB RXS VDD
R6
10K GND
R70
22K
R1
200K
R63
10M 1/4W GND 2 3 Red R98 1K 4 D2 1
2 3 4
U14A
D
R15
22K
R78
22K
C3 C2
0.1uF
R10
10K
C1
0.1uF 0.1uF
5 6 7 OHI RING 8 9 10 11 12 13 14
R4
150K 1 3
Q1
CPC5602C
TP11
8 OHI 9 Green R109 1K U14C D3 10
R11
10K
24 23 22
TP8
1
CIDI
W 36
2 2
TP9 C4
0.1uF
DVDD 1.2M 20 19 18 17 14 R32 11 U14D 13 R25 10K 12 10K 21
1
R64 C28
0.47uF
W 35
R89
100
R83
8.2 GND
C5
0.1uF C
15
R3
150K
16
R105
10
R106
10
TP6 TP12 TP7 R90
1M
C27
0.01uF
R88
402K 1%
7
C
R86 C10
220pF 2KV AVDD
R84
300
R91 C11
1.5M
GND
806K 1%
R92
1.5M
F1
FUSE
L4
BEAD
L1
C8 C9
GND 220pF 2KV BEAD 220pF 2KV
J1
1 2 3 4 5 6 RJ12
C21
0.1uF
C50
10uF
220pF 2KV
R85 R87 C76 C14
560pF 22K 806K 1%1 604 1% 2
D1
P3100SB
W 8 R65 R79
22K
C16
4.7nF GND
48
47
46
45
44
43
42
41
40
39
38
37
L3 BEAD
TP13 R12
L2
BEAD
0.1uF
R66 R80
470 2
DAREFM
ADREFM
DAREFP
ADREFP
NC
AVDD1
INM
AVSS
VMID
INP
FILT
NC
J9
1
1 2 3 B 4 3
AURXFP AURXM AURXCP DTXOP DTXOM DTXIP DTXIM OUTP OUTM M0 M1
NC NC AVDD2 AVSS NC
36 35 34 33 32 AVDD
470
8
R67
22K AVDD 7 1 3
6 5
R68
22K
C20 J7
0.1uF DVDD1 2
1
C12
W61
1uF
+
C17 1
10uF 2
1.8V
C77
0.1uF
C51
10uF
TP1
3 TLV2462 DVDD
TLV2462
R103 C68
+
1
U12A
C22 R7
1uF
U12B
J2
1
B
W 2
2 3
5 6 7
C78
0.1uF
C71 1
10uF
U1
NC DVDD2 DVSS
31 30 29 28
DVDD DVDD1 44K
R69
44K
C15
1uF
2 DVDB
W 6
2 3
3.3V - 5.0V
1uF
1
W 3
8 9
2 DVDD1 1 10 11
TLV320AIC10
AVDD 10K 1 27 26 25 RING J_DCSI1 5VS 2
1
R8 W 1
3
TP2
L5
+
J3
1
NC M/S ALTIN
C69
1uF
C72
4.7uH
+
C73
10uF AVDB
2
W 7
2 3
3.3V - 5.0V
10uF
R9
J_PD 1 1 10K 2 2 12
MCLK
DOUT
DVSS
SCLK
FLAG
PD RST
DVDD1
TP3
5VS
DCSI FC
FSD
DIN
L6
1
+
J4
+
NC
FS
W40
13 14 15 16 17 18 19 20 21 22 23 24 J_FC 2 1 SHDN OH X_FSX0 FSD0 MS_CLOCK X_CLKX0 X_DX0 X_DR0 1 2 3 4
TP5 J5
1
TP4
C70
1uF
C75
10uF
4.7uH
C74
10uF 2
5V
U9
SHDN BP IN+ INV0GND VDD V0+ 8 7 6 5 2
W 4
3 3
W 5
R104
0
C31
1uF
R95
20K
X_RST A
DVDD1
A
C30
1uF
R94 C29
1uF 20K
TPA4861
C32
+
R101
20K 1uF
C49
10uF
Engineer: Drawn By: FILE: SIZE: Title:
12500 TI Boulevard. Dallas, Texas 75243
R93
20K
TLV320AIC11 EVM Schematic
DATE:
23-Jun-2000
REV: SHEET:
1
OF:
5
1
2
3
4
5
6
1
2
3
4
5
REV
6 Revision History
ECN Number Approved
DVDD 10 11 12 13
DVDD U17B PRE CLK D CLR SN74HC74 C18 Q Q 9 8 560pF R71 7 22K U19D 11 14 12 R26 R28 9 10K R29 10 10K DVDD AVDB 2 R21 10K U16 DVDD 6 1 OE VCC 8 C103 0.1uF 3 W 19 3.3V1 J10 2 4 6 8 10 12 7 5 TLV2462 R75 44K C13 1uF 1 R16 44K 2 R81 470 W38 4 GND OUT 5 XTAL 14 16 EPSON 10.24MHZ 18 20 AVDD R82 R23 10K RP1 470 X_DX0 2 W 37 1 C81 0.1uF C54 10uF C79 1K 48 47 46 45 44 43 42 41 40 39 38 37 0.1uF X_DR0 22 24 26 28 30 32 DAREFM ADREFM NC DAREFP ADREFP AVDD1 AVSS VMID INM NC INP C24 J12 0.1uF FILT 34 NC NC AVDD2 U2 AVSS NC NC TLV320AIC10 DVDD2 DVSS NC M/S ALTIN DVDD1 MCLK DVSS DOUT SCLK FLAG DCSI FC FSD RST 36 35 AVDD 34 33 32 31 DVDD 30 29 1 28 27 26 25 J_DCSI 3 W 11 2 R19 10K DVDD1 C80 0.1uF C53 10uF X_DR1 X_DX1 36 38 40 42 44 46 48 50 52 54 56 58 60 1 CID W 41 2J_FC 62 64 66 W12 68 70 72 74 76 X_CLKOUT DVDD1 78 80 TFM-140 1 3 6 5 7 10 9 12 8 1 3 TLV2462 R24 10K C25 10uF C19 1uF R73 22K 6 U13B 11 14 13 16 15 18 17 20 19 21 23 25 27 29 31 33 35 37 39 41 43 46 45 48 47 50 49 52 51 54 53 56 55 58 57 59 61 63 65 68 67 70 R20 10K 69 72 71 74 73 75 77 79 1 TFM-140 Used for DB support DB_DET 76 W 21 78 80 75 77 79 2 73 71 3 69 67 R111 10K 64 66 63 65 X_RESET 60 62 13 14 15 16 17 18 19 20 21 22 23 24 1 2 1 X_FSX1 1 2 7 W 62 2 3 FSD0 X_CLKOUT W14 XTAL X_CLKX1 W15 X_CLKX0 X_DX1 W16 X_DX0 X_DR1 W17 X_DR0
Engineer: Drawn By: FILE: SIZE:
1
U19C
8
5V1 -12V 12v J15 5V2 3.3V2 3 W 18 2 2 DVDB 4 1 3 D 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 B C 1 8
10K R27 13 10K
SN74HC08 U19B
D C82
AVDD
R30 4 R72 22K 10K R31 5 10K
0.1uF U13A R74 22K 2
C23 J8 AVDD 0.1uF
X_CLKX0 X_FSX0
22 24 26
X_CLKR0 X_FSRO
28 30 32
C
X_CLKX1 X_FSX1
34 36 38
R108 10K R77 20K
R107 10K
1 2 3 4 5 6 7 8 9
AURXFP AURXM AURXCP DTXOP DTXOM DTXIP DTXIM OUTP OUTM M0 M1 PD
X_CLKR1 X_FSR1
40 42 44
DVDD R22 10K DVDD 3 2
1 1 R17 10K 2
3 W 10 3 W 9 J_PD
10 11 12
W 22 B DVDD 1
2
DIN
NC
R18 10K X_RESET U19A 3 2 U15 1 2 3 RST GND MR TPS3823 5 2 2 6 2 W60 1 W39 1 SN74HC02 C33 R96 1uF 20K 3 4 U14B 4 SHDN 1 WDI 4 14 DVDD VDD 5 4 3 2 1
1 SW1
PRE CLK D CLR
Q Q
5 6
X_RST
DVDD1
FSD1
U17A SN74HC74
FS
W13 1
DVDD DVSS
U10 SHDN BP IN+ INV0GND VDD V0+ 8 J6 7 5VS 6 2 5 + C34 1uF C52 10uF 1 R13 10K
MS_CLOCK 2
DVDD1 2 1 1 3
TPA4861 A C35 1uF C36 1uF R100 20K R99 20K R102 20K
3
R76 1K 2
2 1
W20
3
A 3 1 J_DCSI1 12500 TI Boulevard. Dallas, Texas 75243
Title:
2
3
TLV320AIC11 EVM Schematic
DATE:
23-Jun-2000
REV: SHEET:
2
OF:
5
1
2
3
4
5
6
1
2
3
4
5
REV
6 Revision History
ECN Number Approved
W 44 W 43 W 42
D A110 A10 A11 A19 A18 A14 A17 A15 A16 A15 A14 A13 A12 A11 A10
W 47 W 46 W 45
A210 A20 A21 A29 A28 A24 A27 A25 A26 A25 A24 A23 A22 A21 A20
W 50 W 49 W 48
D A310 A30 DVDD1 A31 A39 A38 A34 A37 A35 A36 A35 A34 A33 A32 A31 A30
DVDD1
R33
10K
R36
10K
R34
10K
R35
10K
DVDD1
R41 R37
10K
R42
10K
R43
10K
R44
10K
R40
10K
R38
10K
R39
10K
10K
R45
10K
R46
10K
R47
10K
W 28 W 24 W 23
A10 A11 A12 A13 A14 A15 A16 A17 A18
W 27
A30 A31 A32 A33 A34 A35 A36 A37 A38
W 26
W 25
A20 A21 A22 A23 A24 A25 A26 A27 A28
C40 C42 C39
C 12 PDA 12 PDA 12 PDA 1uF
C38
1uF
C41 1uF
1uF 11 10
C37
1uF 11 10 1uF 11 10
C
U5
U4
U3
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2 AURXM
AURXM
AURXFP
AURXM
AURXFP
AURXCP
AURXCP
RSTA 13 14 DVDD1 15 DOUTA 16 DINA 17 18 SCLKA 19 MCLKA 20 FSD2 21 FS1 B FCA 22 23 24
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
48 47 46 45 44 43 42 41 40 39 38 37
A19 A110
RSTA 13 14 DVDD1 15 AVDD DOUTA 16 DINA 17 18 SCLKA 19
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
48 47 46 45 44 43 42 41 40 39 38 37
A29 A210
RSTA DVDD1
13 14 15
AURXCP
AURXFP
PD
PD
PD
M1
M0
M1
M0
M1
DTXOM
DTXOM
M0
DTXOM
OUTM
OUTM
OUTM
OUTP
OUTP
DTXOP
DTXOP
OUTP
DTXOP
DTXIM
DTXIM
DTXIM
DTXIP
DTXIP
DTXIP
1
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
48 47 46 45 44 43 42 41 40 39 38 37
A39 A310
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 DVSS ALTIN AVSS NC NC NC
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 DVSS ALTIN AVSS NC NC NC
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 DVSS ALTIN AVSS NC NC NC
AVDD
DOUTA 16 DINA 17 18 SCLKA 19
AVDD
C83
0.1uF
C56
10uF
C84
0.1uF
C57
10uF
C85
0.1uF
C58
10uF
MCLKA 20 FS2 FSD2 21 22 23
MCLKA 20 FSD3 FS2 21 22 23
B
DCSI
DCSI
DCSI
FC
C91
0.1uF
FCA
24
FC
C89
0.1uF
FCA
24
FC
C90
0.1uF
M/S
M/S
M/S
NC
NC
NC
NC
NC
NC
NC
NC 31
DCSIA 25
26
27
28
29
30
31
32
33
34
35
36
DCSIA 25
26
27
28
29
30
31
32
33
34
35
36
DCSIA 25
26
27
28
29
30
32
NC
33
34
35
DVDD
DVDD
DVDD AVDD
15 MCLKA
DOUTA
AVDD RSTA PDA
C86
13 SCLKA 19 DCSIA 11 DINA AVDD 21 FS1 0.1uF 17 FCA
36
C59
10uF
C88
0.1uF
C61
10uF 1 3
C87
23 0.1uF
C60
10uF
5
7
ON
9
S2 W
A 2 4 6 8 X_DR0 10 X_DX0 12 14 MS_CLOCK 16 18 J_DCSI 20 22 X_RST 24
A
X_CLKX0
FSD1
J_PD
J_FC
12500 TI Boulevard. Dallas, Texas 75243
Title:
TLV320AIC10/11EVM
Engineer: Drawn By: FILE: SIZE: DATE:
6-Jun-2000
REV: SHEET:
3
OF:
5
1
2
3
4
5
6
1
2
3
4
5
REV
6 Revision History
ECN Number Approved
W 53 W 52
D
W 56 W 55 W 54
A410 A49 A48 A47 A46 A45 A44 A43 A42 A41 A40 A510 A59 A58 A57 A56 A55 A54 A53 A52 A51 A50
W 59 W 58 W 57
A610 A69 A68 A67 A66 A65 A64 A63 A62 A61 A60 D
W 51
A60
A61
A64
A65
A40 DVDD1
A41
A44
A45
A50
A51
A54
A55 DVDD1
R51
10K
R52
10K
R53
10K
R54
10K
DVDD1
R59 R55
10K
R60
10K
R61
10K
R62
10K
R56
10K
R57
10K
R58
10K
10K
R48
10K
R50
10K
R49
10K
W 30
W 29 W 32
A40 A41 A42 A43 A44 A45 A46 A47 A48
W 34 W 31
W 33
A60 A61 A62 A63 A64 A65 A66 A67 A68
A50
A51
A52
A53
A54
A55
A56
A57
A58
C46
1uF C PDA
C44 C48
C 1uF 1uF
C43 C45
1uF 11 10 9 8 7 6 5 4 3 2 1 12 PDA 1uF 11 10 9 8 7 6 5 4 3 2 1
C47
12 PDA 1uF 11 10 9 8 7 6 5 4 3 2 1
U8
AURXM AURXM AURXFP AURXFP AURXCP AURXCP M1 M0 M1 M0 PD PD OUTM OUTM DTXOM DTXOM OUTP OUTP DTXIM DTXIM DTXOP DTXOP DTXIP DTXIP RSTA 13 48 47 46 45 44 43 42 41 40 39 38 37 AVDD A49 A410 RSTA 13 14 DVDD1 15 DOUTA 16
U7
AURXM 48 47 46 45 44 43 42 41 40 39 38 37 AVDD A59 A510 RSTA 13 14 DVDD1 15 DOUTA 16 DINA 17 18 SCLKA 19 AURXCP AURXFP M1 M0 PD OUTM DTXOM OUTP DTXIM DTXOP DTXIP
12
U6
48 47 46 45 44 43 42 41 40 39 38 37 B AVDD A69 A610
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
RST DVSS DVDD1 DOUT DIN NC SCLK MCLK FSD FS FLAG
INM INP
14 DVDD1 15 DOUTA 16 DINA 17 18 SCLKA 19
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 ALTIN DVSS AVSS NC NC NC
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 ALTIN DVSS AVSS NC NC NC
AVSS AVDD1 NC VMID DAREFM DAREFP ADREFM ADREFP FILT DVDD2 AVDD2 ALTIN DVSS AVSS NC NC NC
C100
0.1uF
C67
10uF
DINA 17 18 SCLKA 19
C95
0.1uF
C62
10uF
C96
0.1uF
C63
10uf
MCLKA 20 FS3 B 21
MCLKA 20 FSD4 21 FS3 22 23
MCLKA 20 21 FSD4 22 23
FSD3 22 23 FCA 24
DCSI
DCSI
DCSI
FC
M/S
M/S
NC
NC
NC
NC
NC
NC
NC
NC
NC
0.1uF
0.1uF
M/S
C92
FCA
24
FC
C93
FCA
24
FC
C94
0.1uF
DCSIA 25
26
27
28
29
30
31
32
33
34
35
36
25
26
27
28
29
30
31
32
33
34
35
36
DCSIA 25
26
27
28
29
30
31
32
33
34
35
DCSIA
DVDD
DVDD
DVDD
AVDD
36
TLV320AIC10
C97
0.1uF MCLKA SCLKA DCSIA
C64
10uf
DOUTA
RSTA
PDA
C99
0.1uF
C66
10uf
FCA
AVDD
FSD3
DINA
AVDD
C98
0.1uF
C65
10uf
A
A
12500 TI Boulevard. Dallas, Texas 75243
Title: Engineer: Drawn By: FILE: SIZE:
TLV320AIC10/11EVM
DATE:
6-Jun-2000
REV: SHEET:
4
OF:
5
1
2
3
4
5
6
1
2
3
4
5
REV
6 Revision History
ECN Number Approved
D
D
A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A110 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A210 A30 A31 A32 A33 A34 A35 A36 A37 A38 A39 A310
A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A410 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A510 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A610
C
C
J13 1 4 7 10 13 16 19 22 25 28 31 34 2 5 8 11 14 17 20 23 26 29 32 35 3 6 9 12 15 18 21 24 27 30 33 36
J14 1 4 7 10 13 16 19 22 25 28 31 34 2 5 8 11 14 17 20 23 26 29 32 35 3 6 9 12 15 18 21 24 27 30 33 36 B
B
12X3X.1 CRANE PEG36TS-TBR
12X3X.1 CRANE PEG36TS-TBR
A
A
12500 TI Boulevard. Dallas, Texas 75243
Title: Engineer: Drawn By: FILE: SIZE:
TLV320AIC10/11EVM
DATE:
6-Jun-2000
REV: SHEET:
5
OF:
5
1
2
3
4
5
6

▲Up To Search▲

Price & Availability of SLWU003C

	To Download SLWU003C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .