View TDA9321H2_1005291.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA9321H I2C-bus controlled TV input processor
Preliminary specification Supersedes data of 1998 Dec 16 File under Integrated Circuits, IC02 2000 Sep 25
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
FEATURES * Multistandard Vision IF (VIF) circuit with Phase-Locked Loop (PLL) demodulator * Sound IF (SIF) amplifier with separate input for single reference Quasi Split Sound (QSS) mode and separate Automatic Gain Control (AGC) circuit * AM demodulator without extra reference circuit * Switchable group delay correction circuit which can be used to compensate the group delay pre-correction of the B/G TV standard in multistandard TV receivers * Several (I2C-bus controlled) switch outputs which can be used to switch external circuits such as sound traps, etc. * Flexible source selection circuit with 2 external CVBS inputs, 2 Luminance (Y) and Chrominance (C) (or additional CVBS) inputs and 2 independently switchable outputs * Comb filter interface with CVBS output and Y/C input * Integrated chrominance trap circuit * Integrated luminance delay line with adjustable delay time * Integrated chrominance band-pass filter with switchable centre frequency * Multistandard colour decoder with 4 separate pins for crystal connection and automatic search system * PALplus helper demodulator * Possible blanking of the helper signals for PALplus and EDTV-2 * Internal baseband delay line * Two linear RGB inputs with fast blanking; the RGB signals are converted to YUV signals before they are supplied to the outputs; one of the RGB inputs can also be used as YUV input * Horizontal synchronization circuit with switchable time constant for the PLL and Macrovision/subtitle gating * Horizontal synchronization pulse output or clamping pulse input/output * Vertical count-down circuit * Vertical synchronization pulse output * Two-level sandcastle pulse output * I2C-bus control of various functions * Low dissipation. GENERAL DESCRIPTION
TDA9321H
The TDA9321H (see Fig.1) is an input processor for `High-end' television receivers. It contains the following functions: * Multistandard IF amplifier with PLL demodulator * QSS-IF amplifier and AM sound demodulator * CVBS and Y/C switch with various inputs and outputs * Multistandard colour decoder which can also decode the PALplus helper signal * Integrated baseband delay line (64 s) * Sync processor which generates the horizontal and vertical drive pulses for the feature box (100 Hz applications) or display processor (50 Hz applications). The supply voltage for the TDA9321H is 8 V.
2000 Sep 25
2
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
ORDERING INFORMATION TYPE NUMBER TDA9321H PACKAGE NAME QFP64 DESCRIPTION plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 x 20 x 2.8 mm
TDA9321H
VERSION SOT319-2
QUICK REFERENCE DATA SYMBOL Supply VP IP Input signals Vi(VIF)(rms) Vi(SIF)(rms) Vi(CVBS/Y)(p-p) Vi(C)(p-p) Vi(RGB)(p-p) Output signals Vo(VIFO)(p-p) Vo(CVBSPIP)(p-p) Io(TAGC) Vo(QSS)(rms) Vo(AM)(rms) Vo(V)(p-p) Vo(U)(p-p) Vo(Y)(b-w) Vo(hor) Vo(ver) Vo(sc)(p-p) demodulated CVBS output signal (peak-to-peak value) CVBS output signal for Picture-In-Picture (peak-to-peak value) tuner AGC output current QSS output signal (RMS value) demodulated AM sound output signal (RMS value) -V output signal (peak-to-peak value) -U output signal (peak-to-peak value) Y output signal (black-to-white value) horizontal pulse output vertical pulse output subcarrier output signal (peak-to-peak value) - - - 0 - - - - - - - - 2.5 1.0 2.0 - 100 600 1.05 1.33 1.0 5 5 200 - - - 5 - - - - - - - - V V V mA mV mV V V V V V mV VIF amplifier sensitivity (RMS value) SIF amplifier sensitivity (RMS value) CVBS or Y input signal (peak-to-peak value) chrominance input signal (burst amplitude) (peak-to-peak value) RGB input signal (peak-to-peak value) - - - - - 35 100 1.0 0.3 0.7 - - - - - V V V V V supply voltage (pins VP1 and VP2) supply current (pins VP1 and VP2) 7.2 - 8.0 120 8.8 - V mA PARAMETER MIN. TYP. MAX. UNIT
Vo(CVBSTXT)(p-p) CVBS output signal for teletext (peak-to-peak value)
2000 Sep 25
3
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 2000 Sep 25
VIF1 2 VIFVCO1 VIFVCO2 TAGC 7 8 62 VIF AMPLIFIER AND PLL DEMODULATOR AGC/AFC AFC SOUND TRAP VIFO 10 TOP QSS MIXER AM DEMODULATOR SIF AMPLIFIER AGC SUPPLY PULSE GENERATOR VERTICAL DIVIDER I2C-BUS TRANSCEIVER RGB MATRIX VIF2 DECVIF VIFPLL 3 4 6 SIF1 63 SIF2 64 DECSIF QSS/AM 1 5 VP1 VP2 DECDIG DECBG 11 45 33 35 58 VIDEO AMPLIFIER MUTE mute GDI GDO 12 13 GROUP DELAY CORRECTION switch control Y/CVBS CVBSint 14 AV1 15 CVBS1 16 AV2 17 CVBS2 18 SW0 19 CVBS/Y3 C3 SW1 CVBS/Y4 C4 AS 20 21 22 23 24 48 VIDEO SWITCHES AND CONTROL Y/C DETECTOR BANDPASS FILTER hue AUTOMATIC CHROMINANCE CONTROL CLOCHE FILTER FILTER TUNING fsc SECAM DECODER PAL(NTSC)/ SECAM SWITCH 53 DECSEC helper R-Y B-Y VIDEO IDENTIFICATION SYNC SEPARATOR SYNC IN-LOCK DETECTOR
BLOCK DIAGRAM
Philips Semiconductors
PH1LF HA/CLP SCO 60 59
handbook, full pagewidth
VA 61 SCL 46 SDA 47 RI1 GI1 BI1 RGB1 36 37 38 39 41 42 43 40 Y-delay Y Y U V RI2 GI2 BI2 RGB2 YO UO VO 49 50 51
I2C-bus controlled TV input processor
TDA9321H
VCO AND HORIZONTAL PLL
VERTICAL SYNC SEPARATOR
Y-DELAY
Y/U/V SWITCH
IDENT Y Y-SWITCH AND TRAPS U V
BASEBAND DELAY LINE
XTALA
XTALB
XTALC
XTALD
4
34 32
PAL/NTSC PLL HUE CONTROL
SYSTEM IDENTIFICATION
PAL/NTSC DEMODULATOR
26
25
27
28
29
9 GND1
31 GND2
44 GND3
30 REFO
54
55
56
57
52 LFBP
MGR473
CVBSTXT CVBSPIP CVBSCF SYS1 SYS2 YCF CCF
Preliminary specification
COMB FILTER
subcarrier
TDA9321H
Fig.1 Block diagram.
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
PINNING SYMBOL PIN DECSIF VIF1 VIF2 DECVIF QSS/AM VIFPLL VIFVCO1 VIFVCO2 GND1 VIFO VP1 GDI GDO CVBSint AV1 CVBS1 AV2 CVBS2 SW0 CVBS/Y3 C3 SW1 CVBS/Y4 C4 SYS1 CVBSCF SYS2 YCF CCF REFO GND2 CVBSPIP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 VIF input 1 VIF input 2 VIF AGC decoupling combined QSS and AM sound output VIF PLL filter VIF VCO tuned circuit 1 VIF VCO tuned circuit 2 main supply ground VIF output positive supply 1 (+8 V) group delay correction input group delay correction output internal CVBS input AV input 1 CVBS input 1 AV input 2 CVBS input 2 switch output bit 0 (I2C-bus) CVBS or luminance input 3 chrominance input 3 switch output bit 1 (I2C-bus) CVBS or luminance input 4 chrominance input 4 system output 1 for comb filter CVBS output for comb filter system output 2 for comb filter luminance input from comb filter chrominance input from comb filter reference output (subcarrier) digital supply ground CVBS output for Picture-In-Picture VA TAGC SIF1 SIF2 61 62 63 64 DESCRIPTION SIF AGC decoupling SYMBOL PIN DECDIG CVBSTXT DECBG RI1 GI1 BI1 RGB1 RGB2 RI2 GI2 BI2 GND3 VP2 SCL SDA AS YO UO VO LFBP DECSEC XTALA XTALB XTALC XTALD PH1LF SCO HA/CLP 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
TDA9321H
DESCRIPTION digital supply decoupling CVBS output for teletext band gap decoupling red input 1 green input 1 blue input 1 RGB insertion input 1 RGB insertion input 2 red input 2 green input 2 blue input 2 ground 3 positive supply 2 (+8 V) serial clock input (I2C-bus) serial data input/output (I2C-bus) address select input (I2C-bus) luminance output U-signal output V-signal output loop filter burst phase detector SECAM PLL decoupling crystal A (4.433619 MHz) crystal B (3.582056 MHz) crystal C (3.575611 MHz) crystal D (3.579545 MHz) phase 1 loop filter sandcastle pulse output horizontal pulse output or clamp pulse input/output vertical pulse output tuner AGC output SIF input 1 SIF input 2
2000 Sep 25
5
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
60 HA/CLP
57 XTALD
56 XTALC
55 XTALB
54 XTALA
handbook, full pagewidth
53 DECSEC
58 PH1LF
62 TAGC
DECSIF VIF1 VIF2 DECVIF QSS/AM VIFPLL VIFVCO1 VIFVCO2 GND1
52 LFBP 51 VO 50 UO 49 YO 48 AS 47 SDA 46 SCL 45 VP2 44 GND3 43 BI2 42 GI2 41 RI2 40 RGB2 39 RGB1 38 BI1 37 GI1 36 RI1 35 DECBG 34 CVBSTXT 33 DECDIG CVBSPIP 32
1 2 3 4 5 6 7 8 9
VIFO 10 VP1 11 GDI 12 GDO 13 CVBSint 14 AV1 15 CVBS1 16 AV2 17 CVBS2 18 SW0 19 CVBS/Y3 20 C3 21 SW1 22 CVBS/Y4 23 C4 24
TDA9321H
SYS1 25
59 SCO
64 SIF2
63 SIF1
61 VA
CVBSCF 26
SYS2 27
YCF 28
CCF 29
REFO 30
GND2 31
MGR474
Fig.2 Pin configuration.
2000 Sep 25
6
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
FUNCTIONAL DESCRIPTION Vision IF amplifier The VIF amplifier contains three AC-coupled control stages with a total gain control range higher than 66 dB. The sensitivity of the circuit is comparable with that of modern IF-ICs. The video signal is demodulated by a PLL carrier regenerator, which contains a frequency detector and a phase detector. During acquisition, the frequency detector tunes the VCO to the correct frequency. The initial adjustment of the oscillator is realized via the I2C-bus. The switching between SECAM L and L' can also be realized via the I2C-bus. After lock-in, the phase detector controls the VCO so that a stable phase relationship between the VCO and the input signal is achieved. The VCO operates at twice the IF frequency. The reference signal for the demodulator is obtained by means of a frequency divider circuit. To get good performance for phase modulated carrier signals, the control speed of the PLL can be increased by bit FFI. The AFC output is obtained by using the VCO control voltage of the PLL and can be read via the I2C-bus. For fast search tuning systems, the window of the AFC can be increased with a factor 3. The setting is realized with bit AFW. The AGC detector operates on top sync and top white level. The demodulation polarity is switched via the I2C-bus. The AGC detector time constant capacitor is connected externally: mainly because of the flexibility of the application. The time constant of the AGC system during positive modulation is rather long, to avoid visible variations of the signal amplitude. To improve the speed of the AGC system, a circuit is included that detects whether the AGC detector is activated every frame period. When no action is detected during three field periods, the speed of the system is increased. For signals without peak white information, the system automatically switches to a gated black level AGC. Because a black level clamp pulse is required for this mode of operation, the circuit only switches to black level AGC in the internal mode. The circuit contains a video identification (ident) circuit which is independent of the synchronization circuit. Therefore, search tuning is possible when the display section of the receiver is used as a monitor. However, this ident circuit cannot be made as sensitive as the slower sync ident circuit (bit SL) and we recommend the use of both ident outputs to obtain a reliable search system. The ident output is supplied to the tuning system via the I2C-bus.
TDA9321H
The input of the ident circuit is connected to pin 14 (see Fig.3). This has the advantage that the ident circuit can also be activated when a scrambled signal is received (descrambler connected between the IF video output (pins 10 and 14). A second advantage is that the ident circuit can be used when the VIF amplifier is not used (e.g. with built-in satellite tuners). The video ident circuit can also be used to identify the selected CBVS or Y/C signal. The switching between the two modes can be realized with bit VIM. The TDA9321H contains a group delay correction circuit which can be switched between the BG and a flat group delay response characteristic. This has the advantage that no compromise has to be made in multistandard receivers for the choice of the SAW filter. Both the input and output of the group delay correction circuit are externally available, so that the sound trap can be connected between the IF video output and the group delay correction input. The output signal of the correction circuit can be supplied to the video processing circuit and to the external SCART plug. The IC has several (I2C-bus controlled) output ports which can be used to switch sound traps or other external components. When the VIF amplifier is not used, the complete VIF amplifier can be switched off with bit IFO via the I2C-bus. Sound circuit The SIF amplifier is similar to the VIF amplifier and has a gain control range of approximately 66 dB. The AGC circuit is related to the SIF carrier levels (average level of AM or FM carriers) and ensures a constant signal amplitude of the AM demodulator and the QSS mixer. The single reference QSS mixer is realized by a multiplier. This multiplier converts the SIF signal to the intercarrier frequency by mixing it with the regenerated picture carrier from the VCO. The mixer output signal is supplied to the output via a high-pass filter to attenuate the residual video signals. With this system, a high performance hi-fi stereo sound processing can be achieved. The AM sound demodulator is realized by a multiplier. The modulated SIF signal is multiplied in phase with the limited SIF signal. The demodulator output signal is supplied to the output via a low-pass filter to attenuate the carrier harmonics.
2000 Sep 25
7
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Video switches The circuit has three CVBS inputs (one internal and two external inputs) and two Y/C inputs. The Y/C inputs can also be used as additional CVBS inputs. The switch configuration is given in Fig.3. The various sources are selected via the I2C-bus. The circuit can be set in a mode in which it automatically detects whether a CVBS or a Y/C signal is supplied to the Y/C inputs. In this mode, the TV standard is first identified on the added Y/CVBS and the C input signal. Then, both chrominance input signal amplitudes are checked once and the input signal with the highest burst signal amplitude is selected. The result of the detection can be read via the I2C-bus. The IC has two inputs (AV1 and AV2), which can be used to read the status levels of pin 8 of the SCART plug. The information is available in the output status byte 02 in bits D0 to D3. The three outputs of the video switch (CVBSTXT, CVBSPIP and COMBCVBS) can be independently switched to the various input signals. The names are just arbitrary and it is for instance possible to use the COMBCVBS signal to drive the comb filter and the teletext decoder in parallel and to supply the CVBSTXT signal to the SCART plug (via an emitter follower). For comb filter interfacing, the circuit has the COMBCVBS output, a third Y/C input, a reference signal output (fsc) and two control pins which switch the comb filter to the standard of the incoming signal (as detected by the ident circuit of the colour decoder). When the comb filter is enabled by bit ECMB and a signal is recognized which can be combed, the Y/C signals coming from the comb filter are automatically selected if the original source is a CVBS signal, indicated via the CMB-bit in output status byte 02 (D5). For signals which cannot be combed (like SECAM or Black-to-White signals) and for Y/C input signals, the Y/C signals coming from the comb filter are not selected. Chrominance and luminance processing The circuits contain a chrominance bandpass, a SECAM cloche filter and a chrominance trap circuit. The filters are realized by means of gyrator circuits and they are automatically calibrated by comparing the tuning frequency with the crystal frequency of the decoder. The luminance delay line is also realized by means of gyrator circuits. The centre frequency of the chrominance bandpass filter is switchable via the I2C-bus so that the performance can be optimized for `front-end' signals and external CVBS signals. 2000 Sep 25 8
TDA9321H
The luminance output signal which is derived from the incoming CVBS or Y/C signal can be varied in amplitude by means of a separate gain setting control via the I2C-bus control bits GAI1 and GAI0. The gain variation which can be realized with these bits is -1 to +2 dB. Colour decoder The colour decoder can decode PAL, NTSC and SECAM signals. The PAL/NTSC decoder contains an alignment-free crystal oscillator with four separate crystal pins, a killer circuit and two colour difference demodulators. The 90 phase shift for the reference signal is made internally. Because it is possible to connect four different crystals to the colour decoder, all colour standards can be decoded without external switching circuits. Which crystals are connected to the decoder must be indicated via the I2C-bus. The crystal connection pins that are not used must be left open circuit. The horizontal oscillator is calibrated by means of the crystal frequency of the colour PLL. For a reliable calibration, it is very important that crystal indication bits XA to XD are not corrupted. For this reason, the crystal bits can be read in the output bytes so that the software can check the I2C-bus transmission. The ICs contain an Automatic Colour Limiting (ACL) circuit, which can be switched via the I2C-bus and which prevents oversaturation occurring when signals with a high chrominance-to-burst ratio are received. The ACL circuit is designed such that it only reduces the chrominance signal and not the burst signal. This has the advantage that the colour sensitivity is not affected by this function. The ACL function is mainly intended for NTSC signals but it can also be used for PAL signals. For SECAM signals, the ACL function should be switched off. The SECAM decoder contains an auto-calibrating PLL demodulator which has two references: the 4.43 MHz sub-carrier frequency (which is obtained from the crystal oscillator which is used to tune the PLL to the desired free-running frequency) and the bandgap reference (to obtain the correct absolute value of the output signal). The VCO of the PLL is calibrated during each vertical blanking period, when the IC is in search or SECAM mode. The circuit can also decode the PALplus helper signal and can insert the various reference signals, set-ups and timing signals which are required for the PALplus decoder ICs. The baseband delay line (TDA4665 function) is integrated.
This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in _white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ... 2000 Sep 25
VIM VIDEO IDENTIFICATION ident
Philips Semiconductors
TDA9321H
to luminance/sync processing to chrominance processing
handbook, full pagewidth
I2C-bus controlled TV input processor
+
9
14 CVBSint 16 CVBS1 18 CVBS2 20 CVBS/Y3 21 C3 23 CVBS/Y4 24 C4 28 YCF 29 CCF
+ +
26 CVBSCF
34
32
CVBSPIP
CVBSTXT
MGR475
Preliminary specification
TDA9321H
Fig.3 Video switches and interfacing of video ident.
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
RGB switch and matrix The IC has two RGB inputs with fast switching. The switching of the various sources is controlled via the I2C-bus and the condition of the switch inputs can be read from the I2C-bus status bytes. If the RGB signals are not synchronous with the selected decoder input signal, an external clamp pulse has to be supplied to the HA/CLP input. The IC must be set in this mode via the I2C-bus. In this case, the VA pulse is suppressed by switching the VA output to a high impedance OFF state. When an external RGB signal is mixed into the internal YUV signal, it is necessary to switch-off the PALplus demodulation. To detect the presence of a fast blanking, a circuit is added which forces the MACP and HD bits to zero if a blanking pulse is detected in two consecutive lines. This system is chosen to prevent switching off at every spike that is detected on the fast blanking input. The IC can use input RGB1 as YUV input. This function can be enabled by bit YUV in subaddress 0A (D3). When switched to the YUV input, the input signals must have the same amplitude and polarity as the YUV output signals. The Y signal has to be supplied to the G1 input, the U signal to the B1 input and the V signal to the R1 input. Synchronization circuit The sync separator is preceded by a controlled amplifier that adjusts the sync pulse amplitude to a fixed level. These pulses are fed to the slicing stage, which operates at 50% of the amplitude. The separated sync pulses are fed to the phase detector and to the coincidence detector. This detector detects whether the line oscillator is synchronized and can also be used for transmitter identification. This circuit can be made less sensitive by means of bit STM. This mode can be used during search tuning to avoid the tuning system from stopping at very weak input signals. The PLL has a very high static steepness so that the phase of the picture is independent of the line frequency. Two conditions are possible for the horizontal output pulse: * An HA pulse which has a phase and width that are identical to the incoming horizontal sync pulse * A Clamp Pulse (CLP) which has a phase and width that are identical to the clamp pulse in the sandcastle pulse. Signal HA/CLP is generated by an oscillator that runs at a frequency of 440 x fH. Its frequency is divided by 440 to lock the first loop to the incoming signal. The time constant of the loop can be forced by the I2C-bus (fast or slow).
TDA9321H
If required, the IC can select the time constant, depending on the noise content of the incoming video signal. The free-running frequency of the oscillator is determined by a digital control circuit, which is locked to the reference signal of the colour decoder. When the IC is switched on, the HA/CLP is suppressed and the oscillator is calibrated as soon as all sub-address bytes have been sent. When the frequency of the oscillator is correct, the HA/CLP signal is switched on again. When the coincidence detector indicates an out-of-lock situation, the calibration procedure is repeated. The VA pulse is obtained via a vertical countdown circuit. This circuit has various windows, depending on the incoming signal (50 or 60 Hz standard or no standard). The countdown circuit can be forced to various modes by means of the I2C-bus. To obtain short switching times of the countdown circuit during a channel change, the divider can be forced in the search window by means of bit NCIN. I2C-BUS SPECIFICATION The slave addresses of the ICs are given in Table 1. The circuit operates up to clock frequencies of 400 kHz. Table 1 A6 1 Slave addresses A5 0 A4 0 A3 0 A2 1 A1 A1 A0 1 R/W 1/0
Bit A1 is controlled via pin 48 (AS). When the pin is connected to ground, it is a logic 0; when connected to the positive supply line, it is a logic 1. When this pin is left open, it is connected to ground via an internal resistor. Start-up procedure Read the status bytes until POR = logic 0 and send all subaddress bytes. Check the bus transmission by reading output status bits SXA to SXD. This ensures good operation of the calibration system of the horizontal oscillator. The horizontal output signal is switched on when the oscillator is calibrated. Read the status bytes each time before the data in the IC is refreshed. If POR = logic 1, the procedure mentioned above must be carried out to restart the IC. When this procedure is not followed, the horizontal frequency may be incorrect after power-up or after a power dip. The 00 to 0E subaddresses are valid. The FE and FF subaddresses are reserved for test purposes. The auto-increment mode is available for subaddresses. 10
2000 Sep 25
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Inputs and outputs Table 2 Input status bits SUBADDRESS (HEX) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E DATA BYTE D7 CM3 MACP 0 0 0 FORF 0 0 0 0 0 0 FFI 0 L'FA D6 CM2 HOB 0 0 0 FORS 0 0 0 PIP2 0 0 IFO 0 A6 D5 CM1 HBC GAI1 A5 0 FOA 0 0 0 PIP1 0 0 GD A5 A5 D4 CM0 HD GAI0 A4 0 FOB 0 0 ECMB PIP0 0 0 MOD A4 A4 D3 XD FCO YD3 A3 0 0 BSY 0 DEC3 0 YUV 0 AFW A3 A3 D2 XC ACL YD2 A2 0 VIM HO 0
TDA9321H
FUNCTION Colour decoder 0 Colour decoder 1 Luminance Hue control Spare Synchronization 0 Synchronization 1 Spare Video switches 0 Video switches 1 RGB switch Output switches Vision IF Tuner takeover Adjustment IF-PLL INPUT CONTROL BITS Table 3
D1 XB CB YD1 A1 0 POC EMG 0 DEC1 TXT1 IE2 OS1 STM A1 A1
D0 XA BPS YD0 A0 0 VID NCIN 0 DEC0 TXT0 IE1 OS0 VSW A0 A0
DEC2 TXT2 ECL 0 IFS A2 A2
Table 4
Crystal indication CONDITION crystal not present crystal present; note 1
Colour decoder mode DECODER MODE PAL/NTSC/SECAM PAL/NTSC PAL NTSC SECAM PAL/NTSC PAL NTSC PAL/NTSC PAL NTSC PAL/NTSC PAL/NTSC PAL NTSC XTAL A A A A A B B B C C C A/B/C/D D D D
XA to XD 0 1 Note
CM3 CM2 CM1 CM0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
PAL/NTSC/SECAM A/B/C/D
1. When a comb filter is used, the various crystals must be connected to the IC as indicated in the pinning diagram. This is required because the ident system switches automatically to the comb filter when a signal is identified which can be combed (correct combination of colour standard and crystal frequency). For applications without comb filter only the crystal on pin XTALA is important (4.43 MHz); to pins XTALB to XTALD an arbitrary 3.5 MHz crystal can be connected.
2000 Sep 25
11
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 5 MACP 0 1 Motion Adaptive Colour Plus (MACP) MODE internal 4.43 MHz trap used external MACP chrominance filtering used; 4.43 MHz trap bypassed and black set-up 200 mV; note 1
TDA9321H
Table 10 Chrominance band-pass centre frequency CB 0 1 fc 1.1 x fc CENTRE FREQUENCY
Table 11 Bypass of chrominance baseband delay line BPS 0 1 active bypassed DELAY LINE MODE
Note 1. The black set-up will only be present in a norm sync condition. Table 6 HOB 0 1 1 1 Note 1. X = don't care. Table 7 HD 0 1 Note 1. Black and helper set-up will only be present in a norm sync condition. Table 8 FCO 0 1 Table 9 ACL 0 1 not active active not active active Automatic colour limiting COLOUR LIMITING Forced colour on MODE off on; PALplus mode with helper set-up 400 mV and black set-up 200 mV; note 1 PALplus helper demodulation active CONDITIONS Helper output blanking (PALplus/EDTV-2) HBC X(1) 0 1 1 SNR X(1) X(1) 0 1 off on off on BLANKING
Table 12 Gain luminance channel GAI1 0 0 1 1 GAI0 0 1 0 1 -1 dB 0 dB +1 dB +2 dB GAIN SETTING
Table 13 Y-delay adjustment; notes 1 and 2 YD0 to YD3 YD3 YD2 YD1 YD0 Notes 1. For an equal delay of the luminance and chrominance signal the delay must be set at a value of 280 ns (YD3 to YD0 = 1011). This is only valid for a CVBS signal without group delay distortions. 2. The total Y-delay is the addition of: YD3 + YD2 + YD1 + YD0. Table 14 Forced field frequency FORF FORS 0 0 1 1 Note 1. When switched to this mode the divider will directly switch to forced 60 Hz only. 0 1 0 1 FIELD FREQUENCY auto (60 Hz when line not synchronized) forced 60 Hz; note 1 keep last detected field frequency auto (50 Hz when line not synchronized) YD3 x 160 ns YD2 x 160 ns YD1 x 80 ns YD0 x 40 ns Y-DELAY
2000 Sep 25
12
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 15 Phase 1 (1) time constant; see also Table 57 FOA 0 0 1 1 FOB 0 1 0 1 normal slow slow or fast fast MODE Table 19 Blanked sync on pin YO BSY 0 1 Note blanked sync
TDA9321H
CONDITIONS unblanked sync; note 1
1. Except for PALplus with black set-up. Table 20 Condition of horizontal output MODE HO 0 1 CONDITIONS clamp pulse available on pin HA/CLP horizontal pulse available on pin HA/CLP
Table 16 Video ident mode VIM 0 1
ident coupled to internal CVBS (pin 14) ident coupled to selected CVBS
Table 17 Synchronization mode POC 0 1 active not active MODE
Table 21 Enable `Macrovision/subtitle' gating EMG 0 1 disable gating enable gating MODE
Table 18 Video ident mode VID 0 1 not active VIDEO IDENT MODE 1 loop switched-on and off
Table 22 Vertical divider mode NCIN 0 1 VERTICAL DIVIDER MODE normal operation switched to search window
2000 Sep 25
13
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 23 Video switch control ECMB(1) 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 Notes DEC3 0 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 DEC2 0 0 0 1 1 1 1 1 1 0 0 0 1 1 1 1 DEC1 0 1 1 0 0 1 1 0 1 0 1 1 0 1 0 1 DEC0 X(2) 0 1 0 1 0 1 0 0 X(2) 0 1 0 0 0 0 SELECTED SIGNAL CVBSint CVBS1 CVBS2 CVBS3 Y3/C3 CVBS4 Y4/C4 AUTO Y3/C3; note 3 AUTO Y4/C4; note 3 YCF/CCF YCF/CCF YCF/CCF YCF/CCF YCF/CCF AUTO COMB3; note 4 AUTO COMB4; note 4
TDA9321H
SIGNAL TO COMB CVBSint CVBS1 CVBS2 CVBS3 Y3 + C3 CVBS4 Y4 + C4 CVBS3 or Y3 + C3 CVBS4 or Y4 + C4 CVBSint CVBS1 CVBS2 CVBS3 CVBS4 CVBS3 or Y3 + C3 CVBS4 or Y4 + C4
1. When bit ECMB = 1 the subcarrier frequency is present on pin 30. The YCF and CCF signals coming from the comb filter are only switched on when a signal is received that can be combed. 2. X = don't care. 3. AUTO YC means the decoder switches between CVBS and Y/C depending on the presence of the burst signal on these signals. 4. AUTO COMB means the decoder switches to Y/C mode if the burst is present on the C input and to the comb filter output if the burst is present on the CVBS signal. Table 24 Video switch outputs TXT2 PIP2 0 0 0 1 1 1 1 TXT1 PIP1 0 1 1 0 0 1 1 TXT0 PIP0 - 0 1 0 1 0 1 OUTPUT SIGNAL TXT OUTPUT SIGNAL PIP CVBSint CVBS1 CVBS2 CVBS3 Y3 + C3 CVBS4 Y4 + C4 Table 26 External RGB clamp mode ECL 0 1 MODE off; internal clamp pulse used on; external clamp pulse has to be supplied to pin HA/CLP Table 25 Enable YUV input (on RGB1 input) YUV 0 1 RGB1 input active YUV input active MODE
2000 Sep 25
14
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 27 Enable fast blanking RGB1 IE1 0 1 not active active FAST BLANKING Table 33 Modulation standard MOD 0 1 negative positive
TDA9321H
MODULATION
Table 28 Enable fast blanking RGB2 IE2 0 1 not active active FAST BLANKING
Table 34 AFC window AFW 0 1 normal enlarged AFC WINDOW
Table 29 Output switches OS0 and OS1 OS0; OS1 0 1 output = LOW output = HIGH CONDITIONS
Table 35 IF sensitivity IFS 0 1 normal reduced IF SENSITIVITY
Table 36 Search tuning mode Table 30 Fast filter IF-PLL FFI 0 1 CONDITIONS normal time constant fast time constant Table 37 Video mute Table 31 IF circuit not active IFO 0 1 MODE normal operation of IF amplifier IF amplifier switched off Table 38 PLL demodulator frequency shift Table 32 Group delay correction GD 0 1 flat according to BG standard GROUP DELAY CHARACTERISTIC L'FA 0 1 MODE normal IF frequency frequency shift for L' standard VSW 0 1 normal operation VIF signal switched off STATE STM 0 1 normal operation reduced sensitivity of video ident circuit MODE
Table 39 Output status bits FUNCTION Output status bytes SUBADDRESS (HEX) 00 01 02 03 Note 1. X = don't care. DATA BYTE D7 POR CD3 IN1 ID3 D6 X(1) CD2 IN2 ID2 D5 X(1) CD1 CMB ID1 D4 X(1) CD0 YC ID0 D3 SNR SXD S2A IFI D2 FSI SXC S2B PL D1 SL SXB S1A AFA D0 IVW SXA S1B AFB
2000 Sep 25
15
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
OUTPUT CONTROL BITS Table 40 Power-on reset POR 0 1 normal power-down MODE Table 43 Phase 1 (1) lock indication SL 0 1 not locked locked
TDA9321H
INDICATION
Table 44 Condition vertical divider IVW 0 1 STANDARD VIDEO SIGNAL no standard video signal standard video signal in `narrow window' or standard TV norm (525 or 625 lines)
Table 41 Signal-to-noise ratio of sync signal SNR 0 1 SIGNAL-TO-NOISE RATIO S/N > 20 dB S/N < 20 dB
Table 42 Field frequency indication FSI 0 1 50 Hz 60 Hz FREQUENCY
Table 45 Crystal indication (SXA to SXD) SXA to SXD 0 1 CONDITIONS no crystal connected crystal connected
Table 46 Colour decoder mode CD3 0 0 0 0 0 0 0 0 1 1 1 Note 1. This mode is generated when trying (e.g. via software control) to force the decoder to a standard with a crystal which is not connected to the IC. CD2 0 0 0 0 1 1 1 1 0 0 0 CD1 0 0 1 1 0 0 1 1 0 0 1 CD0 0 1 0 1 0 1 0 1 0 1 0 NTSC PAL NTSC PAL NTSC PAL NTSC PAL SECAM illegal forced mode; note 1 STANDARD no colour standard identified XTAL A/B/C/D A A B B C C D D A -
2000 Sep 25
16
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 47 Indication RGB1/RGB2 insertion IN1; IN2 0 1 no insertion full insertion Table 52 In-lock indication IF-PLL Table 48 Condition YCF/CCF inputs from comb filter CMB 0 1 CONDITION YCF/CCF INPUTS not selected selected Table 53 AFC output Table 49 Input signal condition; note 1 YC 0 1 Note 1. During the search mode for the colour system, bit YC will indicate logic 1. Table 50 Condition of AV1 and AV2 inputs S1A; S2A 0 0 1 S1B; S2B 0 1 0 CONDITIONS no external source external source with 4 : 3 input signal external source with 16 : 9 input signal CONDITIONS CVBS signal available Y/C signal available AFA 0 0 1 1 AFB 0 1 0 1 PL 0 1 PLL not locked PLL locked RGB INSERTION Table 51 Output video identification IFI 0 1
TDA9321H
VIDEO SIGNAL no video signal identified video signal identified
CONDITIONS
CONDITIONS outside window; too low outside window; too high in window; below reference in window; above reference
Table 54 IC version indication ID3 0 1 ID2 0 0 ID1 0 0 ID0 1 1 IC TYPE TDA9321HN1 TDA9321HN2
2000 Sep 25
17
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134). SYMBOL VP Tstg Tamb Tsld Tj Ves PARAMETER supply voltage on pins VP1 and VP2 storage temperature operating ambient temperature soldering temperature junction temperature electrostatic handling on all pins notes 1 and 2 notes 1 and 3 Notes 1. All pins are protected against ESD by means of internal clamping diodes. 2. Human Body Model (HBM): R = 1.5 k; C = 100 pF. 3. Machine Model (MM): R = 0 ; C = 200 pF. THERMAL CHARACTERISTICS SYMBOL Rth(j-a) PARAMETER thermal resistance from junction to ambient CONDITIONS in free air VALUE 50 for 5 s CONDITIONS - -25 0 - - -3000 -300 MIN.
TDA9321H
MAX. 9.0 +150 70 260 150 +3000 +300 V
UNIT C C C C V V
UNIT K/W
QUALITY SPECIFICATION Quality specification in accordance with "SNW-FQ-611E". Latch-up performance At an ambient temperature of 70 C all pins meet the following specification: * Positive stress test: Itrigger 100 mA or Vpin 1.5 x VP(max) * Negative stress test: Itrigger -100 mA or Vpin -0.5 x VP(max).
2000 Sep 25
18
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
CHARACTERISTICS VP = 8 V; Tamb = 25 C; unless otherwise specified. SYMBOL PARAMETER CONDITIONS MIN. TYP.
TDA9321H
MAX.
UNIT
Supply (pins VP1 and VP2); note 1 VP IP Ptot supply voltage (pins VP1 and VP2) supply current (pins VP1 and VP2) total power dissipation 7.2 - - 8.0 120 960 8.8 140 - V mA mW
Vision IF circuit VISION IF AMPLIFIER INPUTS (PINS VIF1 AND VIF2) Vi(rms) input sensitivity (RMS value) note 2 fi(VIF) = 38.90 MHz fi(VIF) = 45.75 MHz fi(VIF) = 58.75 MHz Vi(max)(rms) Ri(dif) Ci(dif) Gv fPLL fcr(PLL) tacq(PLL) fVCO/T ftune(VCO) fDAC fshift Vo(z) maximum input signal (RMS value) differential input resistance differential input capacitance voltage gain control range note 3 note 3 - - - 150 - - 64 35 35 40 200 2 3 75 - 2.7 - 300 3.7 29 5.5 200 200 200 - - - 80 V V V mV k pF dB
PLL DEMODULATOR (PLL FILTER ON PIN VIFPLL); note 4 PLL frequency range PLL catching range PLL acquisition time VCO frequency dependency with temperature VCO tuning frequency range frequency variation per step of the DAC (A0 to A6) frequency shift with bit L'FA notes 5 and 6 via I2C-bus 32 2.0 - - 3.0 23 - 60 3.3 20 - 4.2 33 - MHz MHz ms kHz/K MHz kHz MHz
VIDEO AMPLIFIER OUTPUT (PIN VIFO); note 7 zero signal output level note 8 negative modulation positive modulation Vo(ts) Vo(w) Vo Zo(v) Ibias(int) Isource(max) Bv(-3dB) Gdif 2000 Sep 25 top-sync level white level difference in amplitude between negative and positive modulation video output impedance internal bias current of NPN emitter follower output transistor maximum source current -3 dB bandwidth of demodulated output signal differential gain note 9 19 negative modulation positive modulation 4.6 1.9 1.9 4.4 - - 1.0 - 6 - 4.7 2.0 2.0 4.5 0 50 - - 8 - 4.8 2.1 2.1 4.6 15 - - 5 10 1.5 V V V V % mA mA MHz %
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL dif NLvid Vclamp Nclamp Nins dblue
PARAMETER differential phase video non-linearity white spot clamping level noise inverter clamping level noise inverter insertion level (identical to black level) intermodulation at `blue' note 11 note 11 note 10
CONDITIONS notes 6 and 9
MIN. - - - - - - 3
TYP.
MAX. 2.5 5 - - -
UNIT deg % V V V
6.0 1.5 2.7
notes 6 and 12 f = 0.92 or 1.1 MHz f = 2.66 or 3.3 MHz 60 60 56 60 56 49 - - - 66 66 62 66 60 53 5.5 2.5 40 - - - - 65 - - - - dB dB dB dB dB dB mV mV dB
dyellow
intermodulation at `yellow'
notes 6 and 12 f = 0.92 or 1.1 MHz f = 2.66 or 3.3 MHz
S/NW S/NUW Vrc Vrc(2H) PSRR
weighted signal-to-noise ratio unweighted signal-to-noise ratio residual carrier signal 2nd harmonic of residual carrier signal power supply ripple rejection
notes 6 and 13 notes 6 and 13 note 6 note 6 at the output
VIF AND TUNER AGC; note 14
Timing of VIF-AGC with a 2.2 F capacitor (pin DECVIF)
MVI tres modulated video interference response time 60% AM for 1 to 100 mV; 0 to 200 Hz; system B/G VIF input signal amplitude increase of 52 dB; positive and negative modulation VIF input signal amplitude decrease of 52 dB negative modulation positive modulation IL Vo(v) leakage current of the capacitor on negative modulation pin 4 positive modulation change in video output signal amplitude over 1 vertical period for peak white AGC at positive modulation capacitor on pin 4 is 0.5 F - - - - - 50 100 - - - - - 10 200 2 ms ms A nA % - - - 2 10 - % ms
Tuner takeover point adjustment (via I2C-bus)
Vstrt(min)(rms) Vstrt(max)(rms) Vmax minimum start level (RMS value) maximum start level (RMS value) maximum variation with temperature Tamb = 0 to 70 C - 100 - 0.4 150 6 0.8 - 8 mV mV dB
2000 Sep 25
20
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN. - - 5 - - - - 2
TYP.
MAX.
UNIT
Tuner control output (pin TAGC)
Vo(max) Vo(sat) Io(max) IL Vi RESAFC fw maximum output voltage output saturation voltage maximum output current swing leakage current input signal variation for RF AGC for complete tuner control maximum tuner gain; note 3 minimum tuner gain; Io = 2 mA 9 300 - 1 4 - 90 270 V mV mA A dB
- 0.5 -
AFC OUTPUT (VIA I2C-BUS); note 15 AFC resolution window sensitivity I2C-BUS) for identification after the AGC has stabilized on a new transmitter - - 10 ms normal window mode enlarged window mode VIDEO IDENTIFICATION OUTPUT (VIA td delay time 2 65 195 bits kHz kHz 55 175
Sound IF circuit SOUND IF AMPLIFIER (PINS SIF1 AND SIF2) Vi(rms) Vi(max)(rms) Ri(dif) Ci(dif) Gv ct(SIF-VIF) input sensitivity (RMS value) FM mode (-3 dB) AM mode (-3 dB) maximum input signal (RMS value) FM mode AM mode differential input resistance differential input capacitance voltage gain control range crosstalk between inputs SIF and VIF note 3 note 3 - - 50 80 - - 64 50 100 200 70 140 2 3 - - 140 300 - - - - - - V V mV mV k pF dB dB
QSS AND AM SOUND OUTPUT (PIN QSS/AM)
General
Ro VO Ibias(int) Isink(max) Isource(max) output resistance DC output voltage internal bias current of emitter follower maximum AC and DC sink current maximum AC and DC source current - - 0.7 - - - 3.3 1.0 0.7 2.0 250 - - - - V mA mA mA
2000 Sep 25
21
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
QSS output signal
Vo(rms) B-3dB Vr(SC)(rms) S/NW output signal amplitude (RMS value) -3 dB bandwidth residual IF sound carrier (RMS value) weighted signal-to-noise ratio (SC1/SC2) ratio of PC/SC1 at VIF input of 40 dB or higher; note 16 black picture white picture 53/48 58/55 52/47 55/53 - - - - - - dB dB dB dB dB dB SC1 on; SC2 off 70 7.5 - 90 9 2 110 - - mV MHz mV
6 kHz sine wave 44/42 48/46 (black-to-white modulation) 250 kHz sine wave 44/25 48/30 (black-to-white modulation) SC subharmonics (f = 2.75 MHz 3 kHz) SC subharmonics (f = 2.87 MHz 3 kHz) 45/44 51/50 46/45 52/51
AM output signal
Vo(rms) THD B-3dB S/NW output signal amplitude (RMS value) total harmonic distortion -3 dB bandwidth weighted signal-to-noise ratio 54% modulation 500 - 100 47 600 0.5 125 53 700 1.0 - - mV % kHz dB
Video switches and comb filter interface VIDEO SWITCHES FOR CVBS, Y AND C SIGNALS
Signal on pins CVBSint, CVBS1, CVBS2, CVBS/Y3 and CVBS/Y4
Vi(n)(p-p) Ii(n) Zsource(max) sup(n) input voltage (peak-to-peak value) input current maximum source impedance suppression of non-selected signals fi = 0 to 5 MHz; note 6 note 17 - - - 50 1.0 4 - - 1.43 - 1.0 - V A k dB
Signal on pins C3 and C4
Vi(n)(p-p) Zi(n) input voltage (peak-to-peak value) input impedance notes 3 and 18 - - 0.3 50 1.0 - V k
2000 Sep 25
22
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Signal on pin CVBSTXT
Vo(p-p) Vbl Vbl/T Zo Vo(p-p) Vbl Vbl/T Zo output signal amplitude (peak-to-peak value) black level black level dependency with temperature output impedance 1.6 - - - 0.8 - - - 2.0 2.6 4 - 1.0 3.6 9 - 2.4 - - 250 V V mV/K V V mV/K
Signal on pin CVBSPIP
output signal amplitude (peak-to-peak value) black level black level dependency with temperature output impedance 1.2 - - 250
COMB FILTER INTERFACE; note 19
Signal on pin CVBSCF
Vo(p-p) Zo Vbl Vbl/T output signal amplitude (peak-to-peak value) output impedance black level black level dependency with temperature 0.8 - - - 1.0 - 3.6 9 1.2 250 - - V V mV/K
Signal on pin YCF
Vi(p-p) Ii Vi Zi Vo(p-p) VO(en) VO(dis) input voltage (peak-to-peak value) input current - - burst amplitude - - CL = 15 pF 0.2 4.0 - 1.0 4 1.43 - 1.0 - 0.3 4.6 1.4 V A V k
Signal on pin CCF
input voltage input impedance 0.3 50
Reference signal output (pin REFO); note 20
output signal amplitude (peak-to-peak value) DC output level to enable comb filter DC output level to disable comb filter 0.25 4.2 0.1 V V V
Switching levels of SYS1 and SYS2 outputs (pins SYS1 and SYS2); note 21
VOH VOL Io(sink) Io(source) HIGH-level output voltage LOW-level output voltage output sink current output source current 4.0 - 2 2 5.0 0.1 - - 5.5 0.4 - - V V mA mA
2000 Sep 25
23
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
DETECTION OF STATUS LEVELS OF SCART PLUG PIN 8; note 22 Vdet(int-ext) Vdet(ext-ext) Ri detection voltage between internal and external (16 : 9) source detection voltage between external (16 : 9) and external (4 : 3) source input resistance 2.0 5.3 60 2.2 5.5 100 2.4 5.7 - V V k
Chrominance and luminance filters and delay lines CHROMINANCE TRAP CIRCUIT; note 23 ftrap B-3dB trap frequency during SECAM reception -3 dB bandwidth fSC = 3.58 MHz fSC = 4.43 MHz during SECAM reception CSR colour subcarrier rejection CHROMINANCE BAND-PASS CIRCUIT fc Qbp CLOCHE FILTER fc B Y-DELAY LINE td delay time bits YD3 to YD0 = 1011; note 6 crystal A crystal B, C or D td(tr) B tuning range delay time bandwidth with respect to 520/560 ns; 12 settings; see Table 13 note 6 490 530 -280 8 - - 1.8 - - - 520 560 - - 2.0 0.1 2.0 2.4 5 - 550 590 +160 - - 1.0 2.2 - - 250 ns ns ns MHz centre frequency bandwidth 4.26 241 4.29 268 4.31 295 MHz kHz centre frequency band-pass quality factor bit CB = 0 bit CB = 1 - - - fosc 1.1fosc 3 - - - MHz MHz 2.6 3.2 2.9 26 fosc 1% 4.3 1.5% 2.8 3.4 3.1 - 3.0 3.6 3.3 - MHz MHz MHz MHz MHz dB
GROUP DELAY CORRECTION (PINS GDI AND GDO); note 24 Vi(GDI)(p-p) Ii(GDI) Vo(GDO)(p-p) Vo(GDO) Vo(GDO)/T Zo(GDO) input signal amplitude on pin GDI (peak-to-peak value) input current on pin GDI output signal amplitude on pin GDO (peak-to-peak value) output top-sync level on pin GDO top-sync level on pin GDO variation with temperature output impedance on pin GDO V A V V mV/K
2000 Sep 25
24
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Colour demodulation part CHROMINANCE AMPLIFIER CRACC Vo(CRACC) THck(on) hysck(off) ACC control range change in amplitude of the output signals over CRACC threshold colour killer ON hysteresis colour killer OFF colour killer from OFF to ON note 6 strong signal; S/N 40 dB noisy input signals ACL CIRCUIT; note 26 C/CACL ACL chrominance burst ratio when the ACL starts to operate - 3.0 - - - 3 1 - - dB dB note 25 26 - -40 - - - - 2 -35 dB dB dB
REFERENCE PART
Phase-locked loop; note 27
fcr catching range phase shift for a 400 Hz deviation of the oscillator frequency; note 6 360 - 600 - - 2 Hz deg
Oscillator
TCfosc fosc Rneg(min) CL(max) CRhue hue/VP hue/T temperature coefficient of oscillator note 6 frequency oscillator frequency variation with respect to the supply voltage minimum negative resistance maximum load capacitance VP = 8 V 10%; note 6 - - - - 63 steps; see Fig.4 VP 10%; note 6 Tamb = 0 to 70 C; note 6 35 - - - - - - 40 0 0 1 25 1.0 15 - - - Hz/K Hz k pF
HUE CONTROL; note 28 hue control range hue dependency with respect to the supply voltage hue dependency with temperature deg deg deg
DEMODULATORS
General
V/V spread of signal amplitude ratio between standards note 6 -1 - +1 dB
2000 Sep 25
25
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
PAL/NTSC demodulator
G(B-Y)(R-Y) B-3dB(dem) Vo(rc)(p-p) gain between both demodulators (B - Y) and (R - Y) -3 dB bandwidth of demodulators residual carrier output (peak-to-peak value) note 29 f = fosc; (R - Y) output f = fosc; (B - Y) output f = 2fosc; (R - Y) output f = 2fosc; (B - Y) output RRH/2(p-p) Vo/T Vo/VP e H/2 ripple rejection (peak-to-peak value) output voltage variation with temperature output voltage variation with respect to the supply voltage phase error in the demodulated signals at (R - Y) output note 6 note 6 note 6 1.60 - - - - - - - - - 1.78 650 - - - - - 0.1 - - 1.96 - 5 5 5 5 25 - 0.3 5 kHz mV mV mV mV mV %/K dB/V deg
SECAM demodulator
fblos fblos/T fp fp/fz NL Vcal Vo Vr(clk)(p-p) td Vo black level offset frequency black level offset frequency variation with temperature pole frequency of de-emphasis ratio pole and zero frequency non-linearity calibration voltage - - 77 - - 3 -0.1 - delayed signal non-delayed signal difference in output amplitude when delay line is bypassed or not (with bit BPS) - - 85 3 - 4 - - 7 60 93 - 3 5 % V kHz Hz/K kHz
Baseband delay line
variation of output signal residual clock signal (peak-to-peak value) delay for adjacent time samples at constant input signals 0.1 5 dB mV
63.94 64.0 40 - 60 -
64.06 s 80 5 ns %
2000 Sep 25
26
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
PALplus helper demodulator
Vo(helper)(p-p) Vsu(helper) td(g) e(dem) sup helper output voltage (peak-to-peak value) helper set-up amplitude group delay demodulation phase error suppression only helper lines 22 and 23 within pass band including H/2 phase error for modulated helper in demodulated 0 to 1 MHz signal at 4.43 MHz signal in ACC for demodulated mid grey to inserted mid grey level; mid grey line 23 to line 22 bits YD3 to YD0 = 1011; note 30 610 380 - - -36 686 400 - - - 770 420 10 5 - mV mV ns deg dB
Vr THD to(helper-Y) Voffset
residual signal total harmonic distortion helper output timing to Y output offset voltage
-36 -36 - -
- - - -
- - 10 5
dB dB ns mV
tW(su)(helper) td
helper set-up pulse width delay between mid sync of input and start of helper set-up
- - - -
52.8 8.6 30.8 2.6
- - - -
s s s MHz
delay between start of black set-up only lines 22 and 23 and start of helper set-up Bhelper(-3dB) -3 dB bandwidth of helper baseband
RGB switch and YUV switch RGB SWITCH (PINS RI1 TO BI1 AND RI2 TO BI2) Vi(p-p) Zsource(max) Vbl(int-ext) input signal amplitude (peak-to-peak value) maximum source impedance difference between black level of internal and external signals at the outputs input current delay difference between the three channels no clamping; note 3 note 6 - - - 0.7 - - 1.0 1.0 10 V k mV
Ii td
- -
0.1 0
1 20
A ns
2000 Sep 25
27
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER
CONDITIONS
MIN. - - - - -
TYP.
MAX. - - - 1.0 10
UNIT
YUV INPUTS (WHEN ACTIVATED) Vi(Y)(p-p) Vi(U)(p-p) Vi(V)(p-p) Zsource(max) Vbl(int-ext) Y input signal amplitude (peak-to-peak value) U input signal amplitude (peak-to-peak value) V input signal amplitude (peak-to-peak value) maximum source impedance difference between black level of internal and external signals at the outputs input current no clamping; note 3 1.0 1.33 1.05 - - V V V k mV
Ii Vi Vi(max) Ii td(blank-RGB) sup(int) sup(ext) td(blank-YUV)
- - 0.9 - -
0.1 - - - - - - - -
1
A V V V mA ns dB dB ns
FAST BLANKING (PINS RGB1 AND RGB2) input voltage maximum input pulse input current delay difference between blanking and RGB signals suppression of internal YUV signals suppression of external RGB signals delay between blanking input and YUV outputs note 6 data insertion; fi = 0 to 5 MHz; note 6 no data insertion; fi = 0 to 5 MHz; note 6 no data insertion data insertion 0.4 - 3.5 0.2 tbf - - tbf
- 55 55 -
LUMINANCE OUTPUT (PIN YO); note 31 Vo(p-p) Vo output signal amplitude (peak-to-peak value) output voltage during PALplus black-to-white black-to-white - - - - black level 2.8 7 fi = 0 to 5 MHz bit MACP = 1 or bit HD = 1 note 30 Ybl to re-inserted black - 190 - - - 1.0 0.8 - - 3.0 - 52 200 52.8 8.8 - - - 10 250 3.2 - - 210 - - 10 V V mV V MHz dB mV s s mV
Vbl(YUV-RGB) difference in black level between YUV and RGB mode Zo VO BRGB(-3dB) S/N Vsu(bl) tW(su)(bl) td Voffset output impedance output DC voltage level -3 dB bandwidth of the RGB switch circuit signal-to-noise ratio black set-up amplitude black set-up pulse width delay between mid sync at input and black set-up offset voltage
2000 Sep 25
28
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL G(Y/CVBS-YO)
PARAMETER gain from internal Y/CVBS to YO
CONDITIONS bit MACP = 1 or bit HD = 1
MIN. 1.35 1.08
TYP. 1.43 1.14
MAX. 1.50 1.20
UNIT
UO AND VO SIGNAL OUTPUTS (PINS UO AND VO) Vo(VO)(p-p) Vo(UO)(p-p) Zo VO output voltage on pin VO (peak-to-peak value) output voltage on pin UO (peak-to-peak value) output impedance output DC voltage level standard EBU colour bar standard EBU colour bar 0.88 1.12 - 2.2 - 1.05 1.33 - 2.4 - 1.25 1.58 250 2.6 10 V V V mV
Vbl(YUV-RGB) difference in black level between YUV and RGB mode COLOUR MATRIX FROM RGB TO YUV G gain from RI to YO from GI to YO from BI to YO from RI to UO from GI to UO from BI to UO from RI to VO from GI to VO from BI to VO Horizontal and vertical synchronization SYNC VIDEO INPUTS Vsync SLhor SLvert ffr ffr f fmax sync pulse amplitude slicing level for horizontal sync slicing level for vertical sync note 3 note 32 note 32
0.40 0.79 0.15 0.40 0.79 1.19 0.94 0.79 0.15
0.43 0.84 0.16 0.43 0.84 1.27 1.00 0.84 0.16
0.46 0.90 0.17 0.46 0.90 1.35 1.07 0.90 0.17
35 50 35 - -
300 55 40
350 60 45 - 2 0.5 80
mV % %
HORIZONTAL OSCILLATOR free-running frequency spread on free-running frequency frequency dependency with respect to the supply voltage frequency variation with temperature VP = 8.0 V 10%; note 6 Tamb = 0 to 70 C; note 6 15625 - 0.2 - Hz % % Hz
- -
FIRST CONTROL LOOP (PIN PH1LF); note 33 fhr(PLL) fcr(PLL) S/N PLL holding range PLL catching range signal-to-noise ratio note 6 for the video input signal at which the time constant is switched - 0.6 15 0.9 0.9 17 1.2 - 19 kHz kHz dB
hyssw 2000 Sep 25
hysteresis at the switching point 29
2
3
4
dB
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL
PARAMETER sigma value of phase jitter
CONDITIONS in automatic mode; 3
MIN. - -
TYP.
MAX. 5
UNIT ns
HORIZONTAL PULSE OUTPUT AND CLAMP PULSE INPUT/OUTPUT (PIN HA/CLP)
Switched to HA output (bit HO = 1)
VOH VOL Io(sink) Io(source) tW td HIGH-level output voltage LOW-level output voltage output sink current output source current pulse width delay between mid sync of input and mid HA pulse at nominal horizontal frequency note 30 Io(source) = 2 mA Io(sink) = 2 mA 4.0 - 2 2 4.6 0.3 5.0 0.2 - - 4.7 0.45 5.5 0.4 - - 4.8 0.6 V V mA mA s s
Switched to CLP output (bit HO = 0)
tW td1 pulse width delay between start of CLP pulse to start of black set-up delay between mid sync of input and start CLP pulse at nominal horizontal frequency bit HD = 1 or bit MACP = 1; bits YD3 to YD0 = 1011; at nominal horizontal frequency note 30 3.5 5.2 3.6 5.3 3.7 5.4 s s
td2
3.0
3.2
3.4
s
Switched to CLP input (bit ECL = 1)
VIL VIH tW(clamp) V(clamp)(n) Zi ffr flock D/D LR LOW-level input voltage HIGH-level input voltage clamping pulse width clamping offset between pins UO and VO input impedance 0 2.4 1.8 - 3 - - 45 not locked - 488 - - 3.5 - - 50 60 - 625/525 - 0.6 5.5 - 10 - - - 64.5 - 722 V V s mV M
VERTICAL OSCILLATOR; note 34 free-running frequency frequency locking range divider ratio locking range 50 Hz mode 60 Hz mode Hz Hz Hz lines lines/ frame
VERTICAL PULSE OUTPUT (PIN VA) VOH VOL Io(sink) Io(source) tW HIGH-level output voltage LOW-level output voltage output sink current output source current pulse width fVA = 50 Hz fVA = 60 Hz Io(source) = 2 mA Io(sink) = 2 mA 4.0 - 2 2 - - 5.0 0.2 - - 2.5 3.0 5.5 0.4 - - - - V V mA mA lines lines
2000 Sep 25
30
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
SYMBOL td
PARAMETER delay between start of vertical sync note 35 of input and positive edge of vertical pulse on pin VA output impedance
CONDITIONS
MIN. -
TYP. 37.7
MAX. -
UNIT s
Zo
bit ECL = 1
3
-
-
M
SANDCASTLE OUTPUT (PIN SCO)
General
Vz Io(sink) Vo Io(source) tW(h) td zero level voltage output sink current 0 - 2.2 - - - 0.5 0.5 1.0 - 2.8 - - - V mA
Horizontal/vertical blanking
output voltage level output source current horizontal blanking pulse width delay between start horizontal blanking and start clamping pulse 2.5 0.7 10 6.4 V mA s s
Clamping pulse
Vo Io(source) tW td output voltage level output source current pulse width delay between mid sync of input and start of clamping pulse note 30 4.2 - - 3.0 4.5 0.7 3.6 3.2 4.8 - - 3.4 V mA s s
I2C-bus control SCL AND SDA INPUTS/OUTPUTS (PINS SCL AND SDA) Vi VIL VIH IIL IIH VOL(SDA) input voltage range LOW-level input voltage HIGH-level input voltage LOW-level input current HIGH-level input current LOW-level output voltage on pin SDA VIL = 0 V VIH = 5.5 V IOL(SDA) = 3 mA 0 - 3.5 - - - - - - - - - 5.5 1.5 - -10 10 0.4 V V V A A V
SW0 AND SW1 OUTPUTS (PINS SW0 AND SW1); note 36 VOH VOL IO(sink) IO(source) HIGH-level output voltage LOW-level output voltage output sink current output source current 4.0 - 2 2 5.0 0.2 - - 5.5 0.4 - - V V mA mA
Notes to the characteristics 1. The two supply pins VP1 and VP2 must be decoupled separately but they must be connected to a single power supply to avoid too big differences between them. 2. On set AGC. 3. This parameter is not tested during production and is just given as application information for the designer of the television receiver. 2000 Sep 25 31
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
4. Loop filter bandwidth Blpf = 60 kHz (natural frequency fn = 15 kHz; damping factor d = 2; calculated with top sync level as fPLL input signal level). LC-VCO circuit between pins 7 and 8: Q0 = 60; Cint = 30 pF. 5. The optimum temperature stability of the PLL can be obtained when a TOKO coil as given in Table 55 is applied. 6. This parameter is not tested during production but is guaranteed by the design and qualified by means of matrix batches which are made in the pilot production period. 7. Measured at 10 mV (RMS) top sync input signal. 8. So called projected zero point, i.e. with switched demodulator. 9. Measured in accordance with the test line given in Fig.5. For the differential phase test the peak white setting is reduced to 87%. The differential gain is expressed as a percentage of the difference in peak amplitudes between the largest and smallest value relative to the subcarrier amplitude at blanking level. The differential phase is defined as the difference in degrees between the largest and smallest phase angle. 10. This figure is valid for the complete video signal amplitude (peak white-to-black). See Fig.6. 11. The noise inverter is only active in the `strong signal mode' (no noise detected in the incoming signal). 12. The input conditions and test set-up are given in Figs 8 and 9. The figures are measured with an input signal of 10 mV (RMS). 13. Measured at an input signal of 10 mV (RMS). The S/N is the ratio of black-to-white amplitude with respect to the black level noise voltage (RMS value). B = 5 MHz. Weighted in accordance with CCIR 567. 14. The AGC response time also depends on the acquisition time of the PLL demodulator. The values given are valid when the PLL is in lock. 15. The AFC control voltage is obtained from the control voltage of the VCO of the PLL demodulator. The tuning information is supplied to the tuning system via the I2C-bus. Two bits are reserved for this function. The AFC value is valid only when bit PL = 1. 16. The weighted S/N ratio is measured under the following conditions: a) The VIF modulator must meet the following specifications: * Incidental phase modulation for black-to-white jumps less than 0.5 degrees. * QSS AF performance, measured with the television-demodulator AMF2 (audio output, weighted S/N ratio) better than 60 dB (deviation 27 kHz) for 6 kHz sine wave black-to-white modulation. * Picture-to-sound carrier ratio: PC/SC1 = 13 dB (transmitter). b) The measurements must be carried out with the Siemens SAW filters G3962 for VIF and G9350 for SIF. Input level for SIF at 10 mV (RMS) with 27 kHz deviation. c) The PC/SC ratio at the VIF input is calculated as the addition of the TV transmitter ratio and the SAW filter PC/SC ratio. This PC/SC ratio is necessary to achieve the S/NW values as indicated. 17. Signal with negative-going sync. Amplitude includes sync pulse amplitude. 18. Indicated is a signal for a colour bar with 75% saturation (chrominance to burst amplitude ratio = 2.2 : 1). 19. When a signal is identified which can be combed (correct combination of colour standard and reference crystal) the comb filter is switched to that mode via pins 25 and 27 and then the filter is activated by switching on the reference carrier signal and connecting the output signals of the comb filter (pins 28 and 29) to the video processing circuits. 20. The subcarrier output signal can be used as a reference signal for external comb filter ICs (e.g. SAA4961). When bit ECMB = 0 the subcarrier signal is suppressed and the DC level is LOW. When bit ECMB = 1 the output level is HIGH and the subcarrier signal is present. 21. The outputs SYS1 and SYS2 can be used to switch the comb filter to the different colour standards (e.g. PAL-M, PAL-N, PAL-B/G and NTSC-M) and are controlled by the colour decoder identification circuit. The setting of the outputs for the various standards is given in Table 56.
2000 Sep 25
32
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
22. For the detection of the status of the incoming SCART signal a voltage divider with a ratio of 2 : 3 has to be connected between pin 8 of the SCART plug and the detection input. The impedance of the voltage divider should not be too high-ohmic because of the input impedance of 100 k. 23. When the decoder is forced to a fixed subcarrier frequency (via bits XA to XD or bit CM) the chrominance trap is always switched on, also when no colour signal is identified. When 2 crystals are active the chrominance trap is switched off if no colour signal is identified. 24. The typical group delay characteristic for the B/G standard is given in Fig.7. 25. At a chrominance input voltage of 660 mV (p-p) [colour bar with 75% saturation i.e. burst signal amplitude 300 mV (p-p)] the dynamic range of the ACC is +6 and -20 dB. 26. The ACL function can be activated by bit ACL. The ACL circuit reduces the gain of the chrominance amplifier for input signals with a C/CACL which exceeds a value of 3.0. 27. All frequency variations are referenced to 3.58 or 4.43 MHz carrier frequency. All oscillator specifications are measured with the Philips crystal series 9922 520 with a series capacitance Cs = 18 pF. The oscillator circuit is rather insensitive to the spurious responses of the crystal. As long as the resonance resistance of the third overtone is higher than that of the fundamental frequency the oscillator will operate at the correct frequency. The typical crystal parameters for the crystal series are: a) Load resonance frequencies fL: 4.433619, 3.579545, 3.582056 and 3.575611 MHz; Cs = 20 pF. b) Motional capacitance Cmot = 20.6 fF (4.43 MHz crystal) or Cmot = 14.7 fF (3.58 MHz crystal). c) Parallel capacitance Cp = 5.0 pF. The minimum detuning range can only be specified if both the IC and the crystal tolerances are known and therefore the figures regarding catching range are only valid for the specified crystal series. In this figure tolerances of the crystal with respect to the nominal frequency, motional capacitance and ageing have been taken into account and have been counted for gaussic addition. Whenever different typical crystal parameters are used the following equation might be helpful for calculating the impact on the tuning capabilities: C mot Detuning range = -----------------------2 1 + C p ------ Cs The resulting detuning range should be corrected for temperature shift and supply voltage deviation of both the IC and the crystal. To guarantee a catching range of 300 Hz on 4.43 MHz the minimum motional capacitance of the crystal must have a value 13.2 fF or higher. For a catching range of 250 Hz with the 3.58 MHz crystal the minimum motional capacitance must have a value of 9 fF. Note: SMD-type crystals do not fulfil these requirements. The actual series capacitance in the application should be Cs = 18 pF to account for parasitic capacitances on-chip and off-chip. 28. The hue control is active for NTSC on the demodulated colour difference signals and for PALplus on the demodulated helper signal. 29. This parameter indicates the bandwidth of the complete chrominance circuit including the chrominance band-pass filter. The bandwidth of the low-pass filter of the demodulator is approximately 1 MHz. 30. This delay is partially caused by the low-pass filter at the sync separator input. 31. The internal luminance signal (signal which is derived from the incoming CVBS or Y/C signals) has a separate gain control setting (controlled by the I2C-bus bits GAI1 and GAI0 and with a gain variation between -1 and +2 dB) which can be used to get an optimal input signal amplitude for the feature box. 32. The slicing level is independent of sync pulse amplitude. The given percentage is the distance between the slicing level and the black level (back porch). When the amplitude of the sync pulse exceeds the value of 350 mV the sync separator will slice the sync pulse at a level of 175 mV above top sync. The maximum sync pulse amplitude is 4 V (peak-to-peak value).
2000 Sep 25
33
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
33. To obtain a good performance for both weak signal and VCR playback the time constant of the first control loop is switched depending on the input signal condition and the condition of the I2C-bus. Therefore the circuit contains a noise detector and the time constant is switched to the slow mode when too much noise is present in the signal. In the fast mode during the vertical retrace time the phase detector current is increased 50% so that phase errors due to head-switching of the VCR are corrected as soon as possible. Switching between the two modes can be automatic or overruled by the I2C-bus. The circuit contains a video identification circuit which is independent of the first control loop. This identification circuit can be used to close or open the first control loop when a video signal is present or not present on the input. This enables a stable On Screen Display (OSD) when just noise is present at the input. The coupling of the video identification circuit with the first control loop can be revoked via the I2C-bus. To prevent the horizontal synchronization being disturbed by anti copy signals such as Macrovision the phase detector is gated during the vertical retrace period from line 11 to 17 (60 Hz signal) or from line 11 to 22 (50 Hz signal) so that pulses during scan have no effect on the output voltage. The width of the gate pulse is approximately 22 s. During weak signal conditions (noise detector active) the gating is active during the complete scan period and the width of the gate pulse is reduced to 5.7 s so that the effect of noise is reduced to a minimum. The output current of the phase detector in the various conditions is shown in Table 57. 34. The timing pulses for the vertical ramp generator are obtained from the horizontal oscillator via a divider circuit. This divider circuit has 3 modes of operation: a) Search mode large window. This mode is switched on when the circuit is not synchronized or when a non-standard signal [number of lines per frame outside the range between 311 and 314 (50 Hz mode) or between 261 and 264 (60 Hz mode)] is received. In the search mode the divider can be triggered between line 244 and line 361 (approximately 43.3 to 64.5 Hz). b) Standard mode narrow window. This mode is switched on when more than 15 succeeding vertical sync pulses are detected in the narrow window. When the circuit is in the standard mode and a vertical sync pulse is missing the retrace of the vertical ramp generator is started at the end of the window. Consequently, the disturbance of the picture is very small. The circuit will switch back to the search window when, for 6 successive vertical periods, no sync pulses are found within the window. c) Standard TV-norm [divider ratio 525 (60 Hz) or 625 (50 Hz)]. When the system is switched to the narrow window a check is performed to establish whether the incoming vertical sync pulses are in accordance with the TV-norm. When 15 standard TV-norm pulses are counted the divider system is switched to the standard divider ratio mode. In this mode the divider is always reset at the standard value even if the vertical sync pulse is missing. When 3 vertical sync pulses are missed the system switches back to the narrow window and when also in this window no sync pulses are found (condition 3 missing pulses) the system switches over to the search window. The vertical divider needs some waiting time during channel-switching of the tuner. When a fast reaction of the divider is required during channel-switching the system can be forced to the search window by means of bit NCIN in subaddress 06. 35. The delay between the positive edge of VA and the positive edge of CLP ( negative edge of HA) after VA is 32.0 s for field 1 and 0 s for field 2. Especially for PALplus signals the regenerated VA pulses must have a fixed and known phase relation to the undisturbed VA pulses of the incoming video signal. This relationship must remain correct as long as the vertical divider is in the standard mode (indirect sync mode). Therefore the coincidence window used here must be a half line window. With a well defined phase relationship of the generated VA pulses to the generated HA pulses a correct field identification and all the required timing signals referring to a certain line in each frame can be generated externally in the PALplus decoder environment. 36. Pins 19 and 22 are for general purpose outputs that can be used to switch external circuits e.g. sound traps, etc. They are controlled via the I2C-bus by bits OS0 (pin 19) and OS1 (pin 22).
2000 Sep 25
34
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Table 55 Coil data for the VIF-PLL demodulator (approximated coil values) fVIF (MHz) 38.9 45.75 58.75 fVCO (MHz) 77.8 91.5 117.5 L (nH) 150 100 70 TOKO SAMPLE NUMBER P369INAS-159HM P369INAS-160HM P369INAS-161HM REMARKS
TDA9321H
5 mm; 5 km long; TC = 30 100 ppm/C
Table 56 Switching conditions of pins SYS1 and SYS2 COLOUR STANDARD PAL-M PAL-B, G, H, D and I NTSC-M PAL-N SYS1 LOW LOW HIGH HIGH SYS2 LOW HIGH LOW HIGH ACTIVE CRYSTAL C A D B
Table 57 Output current of the phase detector in the various conditions I2C-BUS COMMANDS VID - - - - - - - - 0 - Note 1. Only during vertical retrace, pulse width 22 s and provided that bit EMG = 1 and IVW readout bit = 1. In the other FOA FOB conditions with gating, the pulse width is 5.7 s and the gating is continuous. POC 0 0 0 0 0 0 0 - 0 1 FOA 0 0 0 0 0 1 1 1 - - FOB 0 0 0 1 1 0 0 1 - - IC CONDITIONS IDENT yes yes yes yes yes yes yes - no - COIN yes yes no yes no yes yes - - - NOISE no yes - - - no yes - - - SCAN 180 30 180 30 180 180 30 180 6 - -1 CURRENT/MODE V-RETR 270 30 270 30 270 270 30 270 6 - GATING yes(1) yes no yes no yes yes yes(1) no - MODE auto auto auto slow slow fast slow fast OSD off
2000 Sep 25
35
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
handbook, full pagewidth
MLA739
50 (deg) 30
10
10
30
50
0
10
20
30 40 DAC (HEX)
Fig.4 Hue control curve.
MBC212
16 %
100% 92%
30% for negative modulation 100% = 10% rest carrier
Fig.5 Video output signal.
2000 Sep 25
36
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
handbook, full pagewidth
MBC211
100 (%) 86 72 58 44 30 10 12 22 26 32 36 40 44 48 52 56 60 64 time (s)
Fig.6 Test signal waveform.
MGR476
handbook, halfpage
500
td(g) (ns)
400
300
200
100
0 0 1 2 3 4 f (MHz) 5
Fig.7 Group delay characteristic.
2000 Sep 25
37
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TDA9321H
handbook, full pagewidth
-3.2 dB -10 dB -13.2 dB -30 dB -13.2 dB -30 dB
SC CC BLUE
PC
SC CC YELLOW
PC
MBC213
SC = sound carrier, with respect to top sync level. CC = colour carrier, with respect to top sync level. PC = picture carrier, with respect to top sync level. V O at 3.58 or 4.4 MHz Value at 0.92 or 1.1 MHz = 20 log ----------------------------------------------------------- + 3.6 dB V O at 0.92 or 1.1 MHz V O at 3.58 or 4.4 MHz Value at 2.66 or 3.3 MHz = 20 log ----------------------------------------------------------V O at 2.66 or 3.3 MHz
Fig.8 Input signal conditions.
PC 38.9 MHz
SC 33.4 MHz
ATTENUATOR
TEST CIRCUIT
SPECTRUM ANALYZER
CC 34.5 MHz
gain setting adjusted for blue or yellow
MBC210
Fig.9 Test set-up intermodulation.
2000 Sep 25
38
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
TEST AND APPLICATION INFORMATION
TDA9321H
handbook, full pagewidth
RGB1 RGB2 RI1 GI1 BI1 RI2 GI2 BI2
RI1 GI1 BI1 BL1
RI2 GI2 BI2 BL2
TAGC 62 36 37 38 39 VIF1 2 IF SAW FILTER VIF2 3 40 41 42 43 49 50 51 YO UO VO YIN UIN VIN 30 31 32 33 28 27 26 35 36 37 38 40 41 42 43 RO GO BO BCL BLKIN VDOA VDOB EWO HOUT HFB
CVBS1 AV1 CVBS2 AV2 CVBS/Y3 C3 CVBS/Y4 C4
16 15 18 17 20 21 23 24 34 32 26 CVBSCF 28 YCF
TDA9321H
FEATURE BOX
TDA9330H
44 1
HA 60 61 29 CCF VA
HD VD
2 24 23 8 13
MGR477
3
CVBSTXT CVBSPIP
COMB FILTER
Fig.10 Application diagram.
2000 Sep 25
39
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
PACKAGE OUTLINE QFP64: plastic quad flat package; 64 leads (lead length 1.95 mm); body 14 x 20 x 2.8 mm
TDA9321H
SOT319-2
c
y X
51 52
33 32 ZE
A
e E HE A A2 A1 (A 3) Lp bp 64 1 wM D HD ZD B vM B 19 vMA 20 detail X L
pin 1 index
wM
e
bp
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 3.20 A1 0.25 0.05 A2 2.90 2.65 A3 0.25 bp 0.50 0.35 c 0.25 0.14 D (1) 20.1 19.9 E (1) 14.1 13.9 e 1 HD 24.2 23.6 HE 18.2 17.6 L 1.95 Lp 1.0 0.6 v 0.2 w 0.2 y 0.1 Z D (1) Z E (1) 1.2 0.8 1.2 0.8 7 0o
o
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT319-2 REFERENCES IEC JEDEC MO-112 EIAJ EUROPEAN PROJECTION
ISSUE DATE 97-08-01 99-12-27
2000 Sep 25
40
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. Reflow soldering Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. Typical reflow peak temperatures range from 215 to 250 C. The top-surface temperature of the packages should preferable be kept below 230 C. Wave soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. To overcome these problems the double-wave soldering method was specifically developed. Manual soldering
TDA9321H
If wave soldering is used the following conditions must be observed for optimal results: * Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. * For packages with leads on two sides and a pitch (e): - larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; - smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. * For packages with leads on four sides, the footprint must be placed at a 45 angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical dwell time is 4 seconds at 250 C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications.
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 C. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 C.
2000 Sep 25
41
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE WAVE HLQFP, HSQFP, HSOP, SMS PLCC(3), SQFP SSOP, TSSOP, VSO Notes SO LQFP, QFP, TQFP not suitable(2) suitable not recommended(3)(4) not suitable not recommended(5) suitable suitable suitable suitable suitable
TDA9321H
REFLOW(1)
1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the "Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods". 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45 angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm.
2000 Sep 25
42
Philips Semiconductors
Preliminary specification
I2C-bus controlled TV input processor
DATA SHEET STATUS DATA SHEET STATUS Objective specification PRODUCT STATUS Development DEFINITIONS (1)
TDA9321H
This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Preliminary specification
Qualification
Product specification
Production
Note 1. Please consult the most recently issued data sheet before initiating or completing a design. DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. PURCHASE OF PHILIPS I2C COMPONENTS DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
Purchase of Philips I2C components conveys a license under the Philips' I2C patent to use the components in the I2C system provided the system conforms to the I2C specification defined by Philips. This specification can be ordered using the code 9398 393 40011.
2000 Sep 25
43
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 5F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2451, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 60/14 MOO 11, Bangna Trad Road KM. 3, Bagna, BANGKOK 10260, Tel. +66 2 361 7910, Fax. +66 2 398 3447 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 3341 299, Fax.+381 11 3342 553
For all other countries apply to: Philips Semiconductors, Marketing Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 2000
Internet: http://www.semiconductors.philips.com
SCA 70
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
753504/02/pp44
Date of release: 2000
Sep 25
Document order number:
9397 750 07032

▲Up To Search▲

Price & Availability of TDA9321H2

	To Download TDA9321H2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .