|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Freescale Semiconductor Technical Data MPC8555EEC Rev. 4, 12/2006 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications The MPC8555E integrates a PowerPCTM processor core built on Power ArchitectureTM technology with system logic required for networking, telecommunications, and wireless infrastructure applications. The MPC8555E is a member of the PowerQUICCTM III family of devices that combine system-level support for industry-standard interfaces with processors that implement the embedded category of the Power Architecture technology. For functional characteristics of the processor, refer to the MPC8555E PowerQUICCTM III Integrated Communications Processor Reference Manual. To locate any published errata or updates for this document refer to http://www.freescale.com or contact your Freescale sales office. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Contents Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 8 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 12 Clock Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DDR SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Ethernet: Three-Speed, MII Management . . . . . . . . . . 22 Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 CPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . . . 55 Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 System Design Information . . . . . . . . . . . . . . . . . . . . . 77 Document Revision History . . . . . . . . . . . . . . . . . . . . 84 Device Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . 84 (c) Freescale Semiconductor, Inc., 2004, 2004, 2006. All rights reserved. Overview 1 Overview The following section provides a high-level overview of the MPC8555E features. Figure 1 shows the major functional units within the MPC8555E. DDR SDRAM DDR SDRAM Controller I2C Controller DUART GPIO 32b IRQs Local Bus Controller Programmable Interrupt Controller CPM Time-Slot Assigner Serial DMA Security Engine 256 Kbyte L2 Cache/ SRAM e500 Core 32-Kbyte L1 I Cache 32-Kbyte L1 D Cache e500 Coherency Module Core Complex Bus 64/32b PCI Controller OCeaN 0/32b PCI Controller DMA Controller MPHY UTOPIA MIIs/RMIIs TDMs I/Os FCC FCC SCC SCC/USB SCC SMC SMC SPI I2C ROM I-Memory DPRAM RISC Engine Parallel I/O Baud Rate Generators Timers CPM Interrupt Controller Serial Interfaces 10/100/1000 MAC 10/100/1000 MAC MII, GMII, TBI, RTBI, RGMIIs Figure 1. MPC8555E Block Diagram 1.1 Key Features The following lists an overview of the MPC8555E feature set. * Embedded e500 Book E-compatible core -- High-performance, 32-bit Book E-enhanced core that implements the PowerPC architecture -- Dual-issue superscalar, 7-stage pipeline design -- 32-Kbyte L1 instruction cache and 32-Kbyte L1 data cache with parity protection -- Lockable L1 caches--entire cache or on a per-line basis -- Separate locking for instructions and data -- Single-precision floating-point operations -- Memory management unit especially designed for embedded applications -- Enhanced hardware and software debug support -- Dynamic power management -- Performance monitor facility MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 2 Freescale Semiconductor Overview * * Security Engine is optimized to handle all the algorithms associated with IPSec, SSL/TLS, SRTP, 802.11i, iSCSI, and IKE processing. The Security Engine contains 4 Crypto-channels, a Controller, and a set of crypto Execution Units (EUs). The Execution Units are: -- Public Key Execution Unit (PKEU) supporting the following: - RSA and Diffie-Hellman - Programmable field size up to 2048-bits - Elliptic curve cryptography - F2m and F(p) modes - Programmable field size up to 511-bits -- Data Encryption Standard Execution Unit (DEU) - DES, 3DES - Two key (K1, K2) or Three Key (K1, K2, K3) - ECB and CBC modes for both DES and 3DES -- Advanced Encryption Standard Unit (AESU) - Implements the Rinjdael symmetric key cipher - Key lengths of 128, 192, and 256 bits.Two key - ECB, CBC, CCM, and Counter modes -- ARC Four execution unit (AFEU) - Implements a stream cipher compatible with the RC4 algorithm - 40- to 128-bit programmable key -- Message Digest Execution Unit (MDEU) - SHA with 160-bit or 256-bit message digest - MD5 with 128-bit message digest - HMAC with either algorithm -- Random Number Generator (RNG) -- 4 Crypto-channels, each supporting multi-command descriptor chains - Static and/or dynamic assignment of crypto-execution units via an integrated controller - Buffer size of 256 Bytes for each execution unit, with flow control for large data sizes High-performance RISC CPM operating at up to 333 MHz -- CPM software compatibility with previous PowerQUICC families -- One instruction per clock -- Executes code from internal ROM or instruction RAM -- 32-bit RISC architecture -- Tuned for communication environments: instruction set supports CRC computation and bit manipulation. -- Internal timer -- Interfaces with the embedded e500 core processor through a 32-Kbyte dual-port RAM and virtual DMA channels for each peripheral controller -- Handles serial protocols and virtual DMA MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 3 Overview * -- Two full-duplex fast communications controllers (FCCs) that support the following protocols: - ATM protocol through two UTOPIA level 2 interfaces - IEEE802.3/Fast Ethernet (10/100) - HDLC - Totally transparent operation -- Three full-duplex serial communications controllers (SCCs) support the following protocols: - High level/synchronous data link control (HDLC/SDLC) - LocalTalk (HDLC-based local area network protocol) - Universal asynchronous receiver transmitter (UART) - Synchronous UART (1x clock mode) - Binary synchronous communication (BISYNC) - Totally transparent operation - QMC support, providing 64 channels per SCC using only one physical TDM interface -- Universal serial bus (USB) controller that is full/low-speed compliant (multiplexed on an SCC) - USB host mode - Supports USB slave mode -- Serial peripheral interface (SPI) support for master or slave -- I2C bus controller -- Two serial management controllers (SMCs) supporting: - UART - Transparent - General-circuit interfaces (GCI) -- Time-slot assigner supports multiplexing of data from any of the SCCs and FCCs onto eight time-division multiplexed (TDM) interfaces. The time-slot assigner supports the following TDM formats: - T1/CEPT lines - T3/E3 - Pulse code modulation (PCM) highway interface - ISDN primary rate - Freescale interchip digital link (IDL) - General circuit interface (GCI) -- User-defined interfaces -- Eight independent baud rate generators (BRGs) -- Four general-purpose 16-bit timers or two 32-bit timers -- General-purpose parallel ports--16 parallel I/O lines with interrupt capability 256 Kbytes of on-chip memory -- Can act as a 256-Kbyte level-2 cache -- Can act as a 256-Kbyte or two 128-Kbyte memory-mapped SRAM arrays MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 4 Freescale Semiconductor Overview * * * Can be partitioned into 128-Kbyte L2 cache plus 128-Kbyte SRAM Full ECC support on 64-bit boundary in both cache and SRAM modes SRAM operation supports relocation and is byte-accessible Cache mode supports instruction caching, data caching, or both External masters can force data to be allocated into the cache through programmed memory ranges or special transaction types (stashing) -- Eight-way set-associative cache organization (1024 sets of 32-byte cache lines) -- Supports locking the entire cache or selected lines - Individual line locks set and cleared through Book E instructions or by externally mastered transactions -- Global locking and flash clearing done through writes to L2 configuration registers -- Instruction and data locks can be flash cleared separately -- Read and write buffering for internal bus accesses Address translation and mapping unit (ATMU) -- Eight local access windows define mapping within local 32-bit address space -- Inbound and outbound ATMUs map to larger external address spaces - Three inbound windows plus a configuration window on PCI - Four inbound windows - Four outbound windows plus default translation for PCI DDR memory controller -- Programmable timing supporting first generation DDR SDRAM -- 64-bit data interface, up to MHz data rate -- Four banks of memory supported, each up to 1 Gbyte -- DRAM chip configurations from 64 Mbits to 1 Gbit with x8/x16 data ports -- Full ECC support -- Page mode support (up to 16 simultaneous open pages) -- Contiguous or discontiguous memory mapping -- Sleep mode support for self refresh DDR SDRAM -- Supports auto refreshing -- On-the-fly power management using CKE signal -- Registered DIMM support -- Fast memory access via JTAG port -- 2.5-V SSTL2 compatible I/O Programmable interrupt controller (PIC) -- Programming model is compliant with the OpenPIC architecture -- Supports 16 programmable interrupt and processor task priority levels -- Supports 12 discrete external interrupts -- Supports 4 message interrupts with 32-bit messages MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 -- -- -- -- -- Freescale Semiconductor 5 Overview * * * * * -- Supports connection of an external interrupt controller such as the 8259 programmable interrupt controller -- Four global high resolution timers/counters that can generate interrupts -- Supports additional internal interrupt sources -- Supports fully nested interrupt delivery -- Interrupts can be routed to external pin for external processing -- Interrupts can be routed to the e500 core's standard or critical interrupt inputs -- Interrupt summary registers allow fast identification of interrupt source Two I2C controllers (one is contained within the CPM, the other is a stand-alone controller which is not part of the CPM) -- Two-wire interface -- Multiple master support -- Master or slave I2C mode support -- On-chip digital filtering rejects spikes on the bus Boot sequencer -- Optionally loads configuration data from serial ROM at reset via the stand-alone I2C interface -- Can be used to initialize configuration registers and/or memory -- Supports extended I2C addressing mode -- Data integrity checked with preamble signature and CRC DUART -- Two 4-wire interfaces (RXD, TXD, RTS, CTS) -- Programming model compatible with the original 16450 UART and the PC16550D Local bus controller (LBC) -- Multiplexed 32-bit address and data operating at up to 166 MHz -- Eight chip selects support eight external slaves -- Up to eight-beat burst transfers -- The 32-, 16-, and 8-bit port sizes are controlled by an on-chip memory controller -- Three protocol engines available on a per chip select basis: - General purpose chip select machine (GPCM) - Three user programmable machines (UPMs) - Dedicated single data rate SDRAM controller -- Parity support -- Default boot ROM chip select with configurable bus width (8-, 16-, or 32-bit) Two Three-speed (10/100/1000)Ethernet controllers (TSECs) -- Dual IEEE 802.3, 802.3u, 802.3x, 802.3z AC compliant controllers -- Support for Ethernet physical interfaces: - 10/100/1000 Mbps IEEE 802.3 GMII - 10/100 Mbps IEEE 802.3 MII MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 6 Freescale Semiconductor Overview * * - 10 Mbps IEEE 802.3 MII - 1000 Mbps IEEE 802.3z TBI - 10/100/1000 Mbps RGMII/RTBI -- Full- and half-duplex support -- Buffer descriptors are backwards compatible with MPC8260 and MPC860T 10/100 programming models -- 9.6-Kbyte jumbo frame support -- RMON statistics support -- 2-Kbyte internal transmit and receive FIFOs -- MII management interface for control and status -- Programmable CRC generation and checking OCeaN switch fabric -- Three-port crossbar packet switch -- Reorders packets from a source based on priorities -- Reorders packets to bypass blocked packets -- Implements starvation avoidance algorithms -- Supports packets with payloads of up to 256 bytes Integrated DMA controller -- Four-channel controller -- All channels accessible by both local and remote masters -- Extended DMA functions (advanced chaining and striding capability) -- Support for scatter and gather transfers -- Misaligned transfer capability -- Interrupt on completed segment, link, list, and error -- Supports transfers to or from any local memory or I/O port -- Selectable hardware-enforced coherency (snoop/no-snoop) -- Ability to start and flow control each DMA channel from external 3-pin interface -- Ability to launch DMA from single write transaction PCI Controllers -- PCI 2.2 compatible -- One 64-bit or two 32-bit PCI ports supported at 16 to 66 MHz -- Host and agent mode support, 64-bit PCI port can be host or agent, if two 32-bit ports, only one can be an agent -- 64-bit dual address cycle (DAC) support -- Supports PCI-to-memory and memory-to-PCI streaming -- Memory prefetching of PCI read accesses -- Supports posting of processor-to-PCI and PCI-to-memory writes * MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 7 Electrical Characteristics * * -- PCI 3.3-V compatible -- Selectable hardware-enforced coherency -- Selectable clock source (SYSCLK or independent PCI_CLK) Power management -- Fully static 1.2-V CMOS design with 3.3- and 2.5-V I/O -- Supports power save modes: doze, nap, and sleep -- Employs dynamic power management -- Selectable clock source (sysclk or independent PCI_CLK) System performance monitor -- Supports eight 32-bit counters that count the occurrence of selected events -- Ability to count up to 512 counter specific events -- Supports 64 reference events that can be counted on any of the 8 counters -- Supports duration and quantity threshold counting -- Burstiness feature that permits counting of burst events with a programmable time between bursts -- Triggering and chaining capability -- Ability to generate an interrupt on overflow System access port -- Uses JTAG interface and a TAP controller to access entire system memory map -- Supports 32-bit accesses to configuration registers -- Supports cache-line burst accesses to main memory -- Supports large block (4-Kbyte) uploads and downloads -- Supports continuous bit streaming of entire block for fast upload and download IEEE 1149.1-compliant, JTAG boundary scan 783 FC-PBGA package * * * 2 Electrical Characteristics This section provides the AC and DC electrical specifications and thermal characteristics for the MPC8555E. The MPC8555E is currently targeted to these specifications. Some of these specifications are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O buffer design specifications. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 8 Freescale Semiconductor Electrical Characteristics 2.1 Overall DC Electrical Characteristics This section covers the ratings, conditions, and other characteristics. 2.1.1 Absolute Maximum Ratings Table 1. Absolute Maximum Ratings 1 Characteristic Symbol VDD AVDD GVDD LVDD OVDD MVIN MVREF LVIN OVIN Max Value -0.3 to 1.32 0.3 to 1.43 (for 1 GHz only) -0.3 to 1.32 0.3 to 1.43 (for 1 GHz only) -0.3 to 3.63 -0.3 to 3.63 -0.3 to 2.75 -0.3 to 3.63 -0.3 to (GVDD + 0.3) -0.3 to (GVDD + 0.3) -0.3 to (LVDD + 0.3) -0.3 to (OVDD + 0.3)1 Unit V V V V V V V V V 3 2, 5 2, 5 4, 5 5 Notes Table 1 provides the absolute maximum ratings. Core supply voltage PLL supply voltage DDR DRAM I/O voltage Three-speed Ethernet I/O, MII management voltage CPM, PCI, local bus, DUART, system control and power management, I2C, and JTAG I/O voltage Input voltage DDR DRAM signals DDR DRAM reference Three-speed Ethernet signals CPM, Local bus, DUART, SYSCLK, system control and power management, I2C, and JTAG signals PCI Storage temperature range OVIN TSTG -0.3 to (OVDD + 0.3) -55 to 150 V *C 6 Notes: 1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause permanent damage to the device. 2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 3. Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 4. Caution: LVIN must not exceed LVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during power-on reset and power-down sequences. 5. (M,L,O)VIN and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2. 6. OVIN on the PCI interface may overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as shown in Figure 3. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 9 Electrical Characteristics 2.1.2 Power Sequencing The MPC8555Erequires its power rails to be applied in a specific sequence in order to ensure proper device operation. These requirements are as follows for power up: 1. VDD, AVDDn 2. GVDD, LVDD, OVDD (I/O supplies) Items on the same line have no ordering requirement with respect to one another. Items on separate lines must be ordered sequentially such that voltage rails on a previous step must reach 90 percent of their value before the voltage rails on the current step reach ten percent of theirs. NOTE If the items on line 2 must precede items on line 1, please ensure that the delay will not exceed 500 ms and the power sequence is not done greater than once per day in production environment. NOTE From a system standpoint, if the I/O power supplies ramp prior to the VDD core supply, the I/Os on the MPC8555E may drive a logic one or zero during power-up. 2.1.3 Recommended Operating Conditions Table 2 provides the recommended operating conditions for the MPC8555E. Note that the values in Table 2 are the recommended and tested operating conditions. Proper device operation outside of these conditions is not guaranteed. Table 2. Recommended Operating Conditions Characteristic Core supply voltage PLL supply voltage DDR DRAM I/O voltage Three-speed Ethernet I/O voltage PCI, local bus, DUART, system control and power management, I2C, and JTAG I/O voltage Symbol VDD AVDD GVDD LVDD OVDD Recommended Value 1.2 V 60 mV 1.3 V 50 mV (for 1 GHz only) 1.2 V 60 mV 1.3 V 50 mV (for 1 GHz only) 2.5 V 125 mV 3.3 V 165 mV 2.5 V 125 mV 3.3 V 165 mV Unit V V V V V MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 10 Freescale Semiconductor Electrical Characteristics Table 2. Recommended Operating Conditions (continued) Characteristic Input voltage DDR DRAM signals DDR DRAM reference Three-speed Ethernet signals PCI, local bus, DUART, SYSCLK, system control and power management, I2C, and JTAG signals Die-junction Temperature Symbol MVIN MVREF LVIN OVIN Recommended Value GND to GVDD GND to GVDD GND to LVDD GND to OVDD Unit V V V V Tj 0 to 105 C Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8555E. G/L/OVDD + 20% G/L/OVDD + 5% VIH G/L/OVDD GND GND - 0.3 V VIL GND - 0.7 V Not to Exceed 10% of tSYS1 Note: 1. Note that tSYS refers to the clock period associated with the SYSCLK signal. Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD/LVDD The MPC8555E core voltage must always be provided at nominal 1.2 V (see Table 2 for actual recommended core voltage). Voltage to the processor interface I/Os are provided through separate sets of supply pins and must be provided at the voltages shown in Table 2. The input voltage threshold scales with respect to the associated I/O supply voltage. OVDD and LVDD based receivers are simple CMOS I/O circuits and satisfy appropriate LVCMOS type specifications. The DDR SDRAM interface uses a single-ended differential receiver referenced the externally supplied MVREF signal (nominally set to GVDD/2) as is appropriate for the SSTL2 electrical signaling standard. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 11 Power Characteristics 2.1.4 Output Driver Characteristics Table 3 provides information on the characteristics of the output driver strengths. The values are preliminary estimates. Table 3. Output Drive Capability Driver Type Programmable Output Impedance () 25 42 (default) PCI signals 25 42 (default) DDR signal TSEC/10/100 signals DUART, system control, I2C, JTAG 20 42 42 GVDD = 2.5 V LVDD = 2.5/3.3 V OVDD = 3.3 V 2 Supply Voltage OVDD = 3.3 V Notes Local bus interface utilities signals 1 Notes: 1. The drive strength of the local bus interface is determined by the configuration of the appropriate bits in PORIMPSCR. 2. The drive strength of the PCI interface is determined by the setting of the PCI_GNT1 signal at reset. 3 Power Characteristics Table 4. Power Dissipation(1) (2) CCB Frequency (MHz) 200 Core Frequency (MHz) 400 500 600 267 533 667 800 333 667 833 1000(6) VDD 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.3 Typical Power(3)(4) Maximum Power(5) (W) (W) 4.9 5.2 5.5 5.4 5.9 6.3 6.0 6.5 9.6 6.6 7.0 7.3 7.2 7.7 9.1 7.9 9.3 12.8 The estimated typical power dissipation for this family of PowerQUICC III devices is shown in Table 4. Notes: 1. The values do not include I/O supply power (OVDD, LVDD, GVDD) or AVDD. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 12 Freescale Semiconductor Power Characteristics 2. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance. Any customer design must take these considerations into account to ensure the maximum 105 degrees junction temperature is not exceeded on this device. 3. Typical power is based on a nominal voltage of VDD = 1.2V, a nominal process, a junction temperature of Tj = 105 C, and a Dhrystone 2.1 benchmark application. 4. Thermal solutions will likely need to design to a value higher than Typical Power based on the end application, TA target, and I/O power 5. Maximum power is based on a nominal voltage of VDD = 1.2V, worst case process, a junction temperature of Tj = 105 C, and an artificial smoke test. 6. The nominal recommended VDD = 1.3V for this speed grade. Table 5. Typical I/O Power Dissipation Interface DDR I/O Parameters CCB = 200 MHz CCB = 266 Mhz CCB = 300 Mhz CCB = 333 Mhz PCI I/O 64b, 66Mhz 64b, 33Mhz 32b, 66Mhz 32b, 33Mhz Local Bus I/O 32b, 167Mhz 32b, 133Mhz 32b, 83Mhz 32b, 66Mhz 32b, 33Mhz TSEC I/O MII GMII or TBI RGMII or RTBI CPM - FCC MII RMII HDLC 16 Mbps UTOPIA-8 SPHY UTOPIA-8 MPHY UTOPIA-16 SPHY UTOPIA-16 MPHY 0.015 0.013 0.009 0.06 0.1 0.094 0.135 GVDD (2.5V) 0.46 0.59 0.66 0.73 0.14 0.08 0.07 0.04 0.30 0.24 0.16 0.13 0.07 0.01 0.07 0.04 OVDD (3.3V) LVDD (3.3V) LVDD (2.5V) Unit W W W W W W W W W W W W W W W W W W W W W W W -- -- -- -- -- -- -- -- -- Multiply by number of interfaces used. -- -- -- -- -- -- -- -- Multiply by 2 if using two 32b ports Comments MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 13 Power Characteristics Table 5. Typical I/O Power Dissipation (continued) Interface CPM - SCC TDMA or TDMB TDMA or TDMB Parameters HDLC 16 Mbps Nibble Mode Per Channel GVDD (2.5V) OVDD (3.3V) 0.004 0.01 0.005 LVDD (3.3V) LVDD (2.5V) Unit W W W -- -- Up to 4 TDM channels, multiply by number of TDM channels. Comments MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 14 Freescale Semiconductor Clock Timing 4 4.1 Clock Timing System Clock Timing Table 6. SYSCLK AC Timing Specifications Parameter/Condition Symbol fSYSCLK tSYSCLK tKH, tKL tKHK/tSYSCLK -- Min -- 6.0 0.6 40 -- Typical -- -- 1.0 -- -- Max 166 -- 1.2 60 +/- 150 Unit MHz ns ns % ps Notes 1 -- 2 3 4, 5 Table 6 provides the system clock (SYSCLK) AC timing specifications for the MPC8555E. SYSCLK frequency SYSCLK cycle time SYSCLK rise and fall time SYSCLK duty cycle SYSCLK jitter Notes: 1. Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. 2. Rise and fall times for SYSCLK are measured at 0.6 V and 2.7 V. 3. Timing is guaranteed by design and characterization. 4. This represents the total input jitter--short term and long term--and is guaranteed by design. 5. For spread spectrum clocking, guidelines are +/-1% of the input frequency with a maximum of 60 kHz of modulation regardless of the input frequency. 4.2 TSEC Gigabit Reference Clock Timing Table 7 provides the TSEC gigabit reference clock (EC_GTX_CLK125) AC timing specifications for the MPC8555E. Table 7. EC_GTX_CLK125 AC Timing Specifications Parameter/Condition EC_GTX_CLK125 frequency EC_GTX_CLK125 cycle time EC_GTX_CLK125 rise time EC_GTX_CLK125 fall time EC_GTX_CLK125 duty cycle GMII, TBI RGMII, RTBI Symbol fG125 tG125 tG125R tG125F tG125H/tG125 45 47 Min -- -- -- -- Typical 125 8 -- -- -- 55 53 Max -- -- 1.0 1.0 Unit MHz ns ns ns % 1 1 1, 2 Notes Notes: 1. Timing is guaranteed by design and characterization. 2. EC_GTX_CLK125 is used to generate GTX clock for TSEC transmitter with 2% degradation. EC_GTX_CLK125 duty cycle can be loosened from 47/53% as long as PHY device can tolerate the duty cycle generated by GTX_CLK of TSEC. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 15 RESET Initialization 4.3 Real Time Clock Timing Table 8. RTC AC Timing Specifications Parameter/Condition Symbol tRTCH tRTCL Min 2x tCCB_CLK 2x tCCB_CLK Typical -- -- Max -- -- Unit ns ns Notes Table 8 provides the real time clock (RTC) AC timing specifications. RTC clock high time RTC clock low time 5 RESET Initialization This section describes the AC electrical specifications for the RESET initialization timing requirements of the MPC8555E. Table 9 provides the RESET initialization AC timing specifications. Table 9. RESET Initialization Timing Specifications Parameter/Condition Required assertion time of HRESET Minimum assertion time for SRESET PLL input setup time with stable SYSCLK before HRESET negation Input setup time for POR configs (other than PLL config) with respect to negation of HRESET Input hold time for POR configs (including PLL config) with respect to negation of HRESET Maximum valid-to-high impedance time for actively driven POR configs with respect to negation of HRESET Min 100 512 100 4 2 -- Max -- -- -- -- -- 5 Unit s SYSCLKs s SYSCLKs SYSCLKs SYSCLKs 1 1 1 1 Notes Notes: 1. SYSCLK is identical to the PCI_CLK signal and is the primary clock input for the MPC8555E. See the MPC8555E PowerQUICCTM III Integrated Communications Processor Reference Manual for more details. Table 10 provides the PLL and DLL lock times. Table 10. PLL and DLL Lock Times Parameter/Condition PLL lock times DLL lock times Min -- 7680 Max 100 122,880 Unit s CCB Clocks 1, 2 Notes Notes: 1. DLL lock times are a function of the ratio between the output clock and the platform (or CCB) clock. A 2:1 ratio results in the minimum and an 8:1 ratio results in the maximum. 2. The CCB clock is determined by the SYSCLK x platform PLL ratio. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 16 Freescale Semiconductor DDR SDRAM 6 DDR SDRAM This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the MPC8555E. 6.1 DDR SDRAM DC Electrical Characteristics Table 11 provides the recommended operating conditions for the DDR SDRAM component(s) of the MPC8555E. Table 11. DDR SDRAM DC Electrical Characteristics Parameter/Condition I/O supply voltage I/O reference voltage I/O termination voltage Input high voltage Input low voltage Output leakage current Output high current (VOUT = 1.95 V) Output low current (VOUT = 0.35 V) MVREF input leakage current Symbol GVDD MVREF VTT VIH VIL IOZ IOH IOL IVREF Min 2.375 0.49 x GVDD MVREF - 0.04 MVREF + 0.18 -0.3 -10 -15.2 15.2 -- Max 2.625 0.51 x GVDD MVREF + 0.04 GVDD + 0.3 MVREF - 0.18 10 -- -- 5 Unit V V V V V A mA mA A 4 Notes 1 2 3 Notes: 1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times. 2. MVREF is expected to be equal to 0.5 x GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak noise on MVREF may not exceed 2% of the DC value. 3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be equal to MVREF. This rail should track variations in the DC level of MVREF. 4. Output leakage is measured with all outputs disabled, 0 V VOUT GVDD. Table 12 provides the DDR capacitance. Table 12. DDR SDRAM Capacitance Parameter/Condition Input/output capacitance: DQ, DQS, MSYNC_IN Delta input/output capacitance: DQ, DQS Symbol CIO CDIO Min 6 -- Max 8 0.5 Unit pF pF Notes 1 1 Note: 1. This parameter is sampled. GVDD = 2.5 V 0.125 V, f = 1 MHz, TA = 25C, VOUT = GVDD/2, VOUT (peak to peak) = 0.2 V. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 17 DDR SDRAM 6.2 DDR SDRAM AC Electrical Characteristics This section provides the AC electrical characteristics for the DDR SDRAM interface. 6.2.1 DDR SDRAM Input AC Timing Specifications Table 13. DDR SDRAM Input AC Timing Specifications Table 13 provides the input AC timing specifications for the DDR SDRAM interface. At recommended operating conditions with GVDD of 2.5 V 5%. Parameter AC input low voltage AC input high voltage MDQS--MDQ/MECC input skew per byte For DDR = 333 MHz For DDR < 266 MHz Symbol VIL VIH tDISKEW Min -- MVREF + 0.31 -- Max MVREF - 0.31 GVDD + 0.3 Unit V V ps Notes 1 750 1125 Note: 1. Maximum possible skew between a data strobe (MDQS[n]) and any corresponding bit of data (MDQ[8n + {0...7}] if 0 <= n <= 7) or ECC (MECC[{0...7}] if n = 8). 6.2.2 DDR SDRAM Output AC Timing Specifications Table 14 and Table 15 provide the output AC timing specifications and measurement conditions for the DDR SDRAM interface. Table 14. DDR SDRAM Output AC Timing Specifications for Source Synchronous Mode At recommended operating conditions with GVDD of 2.5 V 5%. Parameter MCK[n] cycle time, (MCK[n]/MCK[n] crossing) Skew between any MCK to ADDR/CMD 333 MHz 266 MHz 200 MHz ADDR/CMD output setup with respect to MCK 333 MHz 266 MHz 200 MHz ADDR/CMD output hold with respect to MCK 333 MHz 266 MHz 200 MHz MCS(n) output setup with respect to MCK 333 MHz 266 MHz 200 MHz Symbol 1 tMCK tAOSKEW Min 6 Max 10 Unit ns ps Notes 2 3 -1000 -1100 -1200 tDDKHAS 2.8 3.45 4.6 tDDKHAX 2.0 2.65 3.8 tDDKHCS 2.8 3.45 4.6 200 300 400 -- ns 4 -- ns 4 -- ns 4 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 18 Freescale Semiconductor DDR SDRAM Table 14. DDR SDRAM Output AC Timing Specifications for Source Synchronous Mode (continued) At recommended operating conditions with GVDD of 2.5 V 5%. Parameter MCS(n) output hold with respect to MCK 333 MHz 266 MHz 200 MHz MCK to MDQS 333 MHz 266 MHz 200 MHz MDQ/MECC/MDM output setup with respect to MDQS 333 MHz 266 MHz 200 MHz MDQ/MECC/MDM output hold with respect to MDQS 333 MHz 266 MHz 200 MHz MDQS preamble start MDQS epilogue end Symbol 1 tDDKHCX Min Max -- Unit ns Notes 4 2.0 2.65 3.8 tDDKHMH -0.9 -1.1 -1.2 tDDKHDS, tDDKLDS 900 900 1200 tDDKHDX, tDDKLDX 900 900 1200 tDDKHMP tDDKLME -0.5 x tMCK - 0.9 -0.9 -0.5 x tMCK +0.3 0.3 ns ns 7 7 -- ps 6 0.3 0.5 0.6 -- ps 6 ns 5 Notes: 1. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from the rising or falling edge of the reference clock (KH or KL) until the output went invalid (AX or DX). For example, tDDKHAS symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are setup (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes low (L) until data outputs (D) are invalid (X) or data output hold time. 2. All MCK/MCK referenced measurements are made from the crossing of the two signals 0.1 V. 3. In the source synchronous mode, MCK/MCK can be shifted in 1/4 applied cycle increments through the Clock Control Register. For the skew measurements referenced for tAOSKEW it is assumed that the clock adjustment is set to align the address/command valid with the rising edge of MCK. 4. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS. For the ADDR/CMD setup and hold specifications, it is assumed that the Clock Control register is set to adjust the memory clocks by 1/2 applied cycle. The MCSx pins are separated from the ADDR/CMD (address and command) bus in the HW spec. This was separated because the MCSx pins typically have different loadings than the rest of the address and command bus, even though they have the same timings. 5. Note that tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). In the source synchronous mode, MDQS can launch later than MCK by 0.3 ns at the maximum. However, MCK may launch later than MDQS by as much as 0.9 ns. tDDKHMH can be modified through control of the DQSS override bits in the TIMING_CFG_2 register. In source synchronous mode, this will typically be set to the same delay as the clock adjust in the CLK_CNTL register. The timing parameters listed in the table assume that these two parameters have been set to the same adjustment value. See the MPC8555E PowerQUICCTM III Integrated Communications Processor Reference Manual for a description and understanding of the timing modifications enabled by use of these bits. 6. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC (MECC), or data mask (MDM). The data strobe should be centered inside of the data eye at the pins of the MPC8555E. 7. All outputs are referenced to the rising edge of MCK(n) at the pins of the MPC8555E. Note that tDDKHMP follows the symbol conventions described in note 1. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 19 DDR SDRAM Figure 3 shows the DDR SDRAM output timing for address skew with respect to any MCK. MCK[n] MCK[n] tMCK tAOSKEWmax) ADDR/CMD CMD tAOSKEW(min) NOOP ADDR/CMD CMD NOOP Figure 3. Timing Diagram for tAOSKEW Measurement Figure 4 shows the DDR SDRAM output timing diagram for the source synchronous mode. MCK[n] MCK[n] tMCK tDDKHAS ,tDDKHCS tDDKHAX ,tDDKHCX ADDR/CMD Write A0 tDDKHMP tDDKHMH MDQS[n] tDDKHDS tDDKLDS MDQ[x] tDDKHDX D0 D1 tDDKLDX tDDKLME NOOP Figure 4. DDR SDRAM Output Timing Diagram for Source Synchronous Mode MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 20 Freescale Semiconductor DUART Figure 5 provides the AC test load for the DDR bus. Output Z0 = 50 GVDD/2 RL = 50 Figure 5. DDR AC Test Load Table 15. DDR SDRAM Measurement Conditions Symbol VTH VOUT Notes: 1. Data input threshold measurement point. 2. Data output measurement point. DDR MVREF 0.31 V 0.5 x GVDD Unit V V Notes 1 2 7 DUART This section describes the DC and AC electrical specifications for the DUART interface of the MPC8555E. 7.1 DUART DC Electrical Characteristics Table 16. DUART DC Electrical Characteristics Parameter Symbol VIH VIL IIN VOH VOL Test Condition VOUT VOH (min) or VOUT VOL (max) VIN 1 = 0 V or VIN = VDD OVDD = min, IOH = -100 A OVDD = min, IOL = 100 A Min 2 -0.3 -- OVDD - 0.2 -- Max OVDD + 0.3 0.8 5 -- 0.2 Unit V V A V V Table 16 provides the DC electrical characteristics for the DUART interface of the MPC8555E. High-level input voltage Low-level input voltage Input current High-level output voltage Low-level output voltage Note: 1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 21 Ethernet: Three-Speed, MII Management 7.2 DUART AC Electrical Specifications Table 17. DUART AC Timing Specifications Parameter Minimum baud rate Maximum baud rate Oversample rate Value fCCB_CLK / 1048576 fCCB_CLK / 16 16 Unit baud baud -- Notes 3 1, 3 2, 3 Table 17 provides the AC timing parameters for the DUART interface of the MPC8555E. Notes: 1. Actual attainable baud rate will be limited by the latency of interrupt processing. 2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit values are sampled each 16th sample. 3. Guaranteed by design. 8 Ethernet: Three-Speed, MII Management This section provides the AC and DC electrical characteristics forthree-speed, 10/100/1000, and MII management. 8.1 Three-Speed Ethernet Controller (TSEC) (10/100/1000 Mbps)--GMII/MII/TBI/RGMII/RTBI Electrical Characteristics The electrical characteristics specified here apply to allGMII (gigabit media independent interface), the MII (media independent interface), TBI (ten-bit interface), RGMII (reduced gigabit media independent interface), and RTBI (reduced ten-bit interface) signals except MDIO (management data input/output) and MDC (management data clock). The RGMII and RTBI interfaces are defined for 2.5 V, while the GMII and TBI interfaces can be operated at 3.3 or 2.5 V. Whether theGMII, MII, or TBI interface is operated at 3.3 or 2.5 V, the timing is compliant with the IEEE 802.3 standard. The RGMII and RTBI interfaces follow the Hewlett-Packard reduced pin-count interface for Gigabit Ethernet Physical Layer Device Specification Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified in Section 8.3, "Ethernet Management Interface Electrical Characteristics." 8.1.1 TSEC DC Electrical Characteristics All GMII, MII, TBI, RGMII, and RTBI drivers and receivers comply with the DC parametric attributes specified in Table 18 and Table 19. The potential applied to the input of a GMII, MII, TBI, RGMII, or RTBI receiver may exceed the potential of the receiver's power supply (i.e., a GMII driver powered from a 3.6-V supply driving VOH into a GMII receiver powered from a 2.5-V supply). Tolerance for dissimilar GMII driver and receiver supply potentials is implicit in these specifications. The RGMII and RTBI signals are based on a 2.5-V CMOS interface voltage as defined by JEDEC EIA/JESD8-5. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 22 Freescale Semiconductor Ethernet: Three-Speed, MII Management Table 18. GMII, MII, and TBI DC Electrical Characteristics Parameter Supply voltage 3.3 V Output high voltage Output low voltage Input high voltage Input low voltage Input high current Input low current Symbol LVDD VOH VOL VIH VIL IIH IIL IOH = -4.0 mA IOL = 4.0 mA -- -- VIN 1 = LVDD VIN = GND 1 Conditions -- LVDD = Min LVDD = Min -- -- Min 3.13 2.40 GND 1.70 -0.3 -- -600 Max 3.47 LVDD + 0.3 0.50 LVDD + 0.3 0.90 40 -- Unit V V V V V A A Note: 1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2. Table 19. GMII, MII, RGMII RTBI, and TBI DC Electrical Characteristics Parameters Supply voltage 2.5 V Output high voltage (LVDD = Min, IOH = -1.0 mA) Output low voltage (LVDD = Min, IOL = 1.0 mA) Input high voltage (LVDD = Min) Input low voltage (LVDD = Min) Input high current (VIN 1 = LVDD) Input low current (VIN 1 = GND) Symbol LVDD VOH VOL VIH VIL IIH IIL Min 2.37 2.00 GND - 0.3 1.70 -0.3 -- -15 Max 2.63 LVDD + 0.3 0.40 LVDD + 0.3 0.70 10 -- Unit V V V V V A A Note: 1. Note that the symbol VIN, in this case, represents the LVIN symbol referenced in Table 1and Table 2. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 23 Ethernet: Three-Speed, MII Management 8.2 GMII, MII, TBI, RGMII, and RTBI AC Timing Specifications The AC timing specifications for GMII, MII, TBI, RGMII, and RTBI are presented in this section. 8.2.1 GMII AC Timing Specifications This section describes the GMII transmit and receive AC timing specifications. 8.2.2 GMII Transmit AC Timing Specifications Table 20. GMII Transmit AC Timing Specifications Table 20 provides the GMII transmit AC timing specifications. At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition GTX_CLK clock period GTX_CLK duty cycle GMII data TXD[7:0], TX_ER, TX_EN setup time GTX_CLK to GMII data TXD[7:0], TX_ER, TX_EN delay GTX_CLK data clock rise and fall times Symbol 1 tGTX tGTXH/tGTX tGTKHDV tGTKHDX tGTXR3, tGTXR2,4 Min -- 40 2.5 0.5 -- Typ 8.0 -- -- -- -- Max -- 60 -- 5.0 1.0 Unit ns % ns ns ns Notes: 1. The symbols used for timing specifications herein follow the pattern t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGTKHDV symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) reaching the valid state (V) to state or setup time. Also, tGTKHDX symbolizes GMII transmit timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) going invalid (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGTX represents the GMII(G) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3. Guaranteed by characterization. 4. Guaranteed by design. Figure 6 shows the GMII transmit AC timing diagram. tGTX GTX_CLK tGTXH TXD[7:0] TX_EN TX_ER tGTKHDX tGTKHDV tGTXF tGTXR Figure 6. GMII Transmit AC Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 24 Freescale Semiconductor Ethernet: Three-Speed, MII Management 8.2.2.1 GMII Receive AC Timing Specifications Table 21. GMII Receive AC Timing Specifications Table 21 provides the GMII receive AC timing specifications. At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition RX_CLK clock period RX_CLK duty cycle RXD[7:0], RX_DV, RX_ER setup time to RX_CLK RXD[7:0], RX_DV, RX_ER hold time to RX_CLK RX_CLK clock rise and fall time Symbol 1 tGRX tGRXH/tGRX tGRDVKH tGRDXKH tGRXR, tGRXF 2,3 Min -- 40 2.0 0.5 -- Typ 8.0 -- -- -- -- Max -- 60 -- -- 1.0 Unit ns % ns ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGRDVKH symbolizes GMII receive timing (GR) with respect to the time data input signals (D) reaching the valid state (V) relative to the tRX clock reference (K) going to the high state (H) or setup time. Also, tGRDXKL symbolizes GMII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tGRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tGRX represents the GMII (G) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3. Guaranteed by design. Figure 7 provides the AC test load for TSEC. Output Z0 = 50 LVDD/2 RL = 50 Figure 7. TSEC AC Test Load Figure 8 shows the GMII receive AC timing diagram. tGRX RX_CLK tGRXH RXD[7:0] RX_DV RX_ER tGRDXKH tGRDVKH tGRXF tGRXR Figure 8. GMII Receive AC Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 25 Ethernet: Three-Speed, MII Management 8.2.3 MII AC Timing Specifications This section describes the MII transmit and receive AC timing specifications. 8.2.3.1 MII Transmit AC Timing Specifications Table 22. MII Transmit AC Timing Specifications Table 22 provides the MII transmit AC timing specifications. At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition TX_CLK clock period 10 Mbps TX_CLK clock period 100 Mbps TX_CLK duty cycle TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay TX_CLK data clock rise and fall time Symbol 1 tMTX2 tMTX tMTXH/tMTX tMTKHDX tMTXR, tMTXF 2,3 Min -- -- 35 1 1.0 Typ 400 40 -- 5 -- Max -- -- 65 15 4.0 Unit ns ns % ns ns Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing (MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). Note that, in general, the clock reference symbol representation is based on two to three letters representing the clock of a particular functional. For example, the subscript of tMTX represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3. Guaranteed by design. Figure 9 shows the MII transmit AC timing diagram. tMTX TX_CLK tMTXH TXD[3:0] TX_EN TX_ER tMTKHDX tMTXF tMTXR Figure 9. MII Transmit AC Timing Diagram 8.2.3.2 MII Receive AC Timing Specifications Table 23 provides the MII receive AC timing specifications. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 26 Freescale Semiconductor Ethernet: Three-Speed, MII Management Table 23. MII Receive AC Timing Specifications At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition RX_CLK clock period 10 Mbps RX_CLK clock period 100 Mbps RX_CLK duty cycle RXD[3:0], RX_DV, RX_ER setup time to RX_CLK RXD[3:0], RX_DV, RX_ER hold time to RX_CLK RX_CLK clock rise and fall time Symbol 1 tMRX2 tMRX tMRXH/tMRX tMRDVKH tMRDXKH tMRXR, tMRXF 2,3 Min -- -- 35 10.0 10.0 1.0 Typ 400 40 -- -- -- -- Max -- -- 65 -- -- 4.0 Unit ns ns % ns ns ns Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing (MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals (D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tMRX represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3. Guaranteed by design. Figure 10 shows the MII receive AC timing diagram. tMRX RX_CLK tMRXH RXD[3:0] RX_DV RX_ER tMRDVKH tMRDXKH tMRXF Valid Data tMRXR Figure 10. MII Receive AC Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 27 Ethernet: Three-Speed, MII Management 8.2.4 TBI AC Timing Specifications This section describes the TBI transmit and receive AC timing specifications. 8.2.4.1 TBI Transmit AC Timing Specifications Table 24. TBI Transmit AC Timing Specifications Table 24 provides the MII transmit AC timing specifications. At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition GTX_CLK clock period GTX_CLK duty cycle GMII data TCG[9:0], TX_ER, TX_EN setup time GTX_CLK going high GMII data TCG[9:0], TX_ER, TX_EN hold time from GTX_CLK going high GTX_CLK clock rise and fall time Symbol 1 tTTX tTTXH/tTTX tTTKHDV tTTKHDX tTTXR, tTTXF 2,3 Min -- 40 2.0 1.0 -- Typ 8.0 -- -- -- -- Max -- 60 -- -- 1.0 Unit ns % ns ns ns Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state )(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTTKHDV symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the valid state (V) or setup time. Also, tTTKHDX symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the invalid state (X) or hold time. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTTX represents the TBI (T) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. Signal timings are measured at 0.7 V and 1.9 V voltage levels. 3. Guaranteed by design. Figure 11 shows the TBI transmit AC timing diagram. tTTX GTX_CLK tTTXH tTTXF TCG[9:0] tTTKHDV tTTKHDX tTTXR tTTXF tTTXR Figure 11. TBI Transmit AC Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 28 Freescale Semiconductor Ethernet: Three-Speed, MII Management 8.2.4.2 TBI Receive AC Timing Specifications Table 25. TBI Receive AC Timing Specifications Table 25 provides the TBI receive AC timing specifications. At recommended operating conditions with LVDD of 3.3 V 5%. Parameter/Condition RX_CLK clock period RX_CLK skew RX_CLK duty cycle RCG[9:0] setup time to rising RX_CLK RCG[9:0] hold time to rising RX_CLK RX_CLK clock rise time and fall time Symbol 1 tTRX tSKTRX tTRXH/tTRX tTRDVKH tTRDXKH tTRXR, tTRXF 2,3 Min Typ 16.0 Max Unit ns 7.5 40 2.5 1.5 0.7 -- -- -- -- -- 8.5 60 -- -- 2.4 ns % ns ns ns Note: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTRDVKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) reach the valid state (V) relative to the tTRX clock reference (K) going to the high (H) state or setup time. Also, tTRDXKH symbolizes TBI receive timing (TR) with respect to the time data input signals (D) went invalid (X) relative to the tTRX clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For example, the subscript of tTRX represents the TBI (T) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (TRX). 2. Guaranteed by design. Figure 12 shows the TBI receive AC timing diagram. tTRX RX_CLK1 tTRXH RXD[9:0] tTRDVKH tSKTRX RX_CLK0 tTRXH tTRDVKH tTRDXKH tTRDXKH tTRXF Valid Data Valid Data tTRXR Figure 12. TBI Receive AC Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 29 Ethernet: Three-Speed, MII Management 8.2.5 RGMII and RTBI AC Timing Specifications Table 26. RGMII and RTBI AC Timing Specifications Table 26 presents the RGMII and RTBI AC timing specifications. At recommended operating conditions with LVDD of 2.5 V 5%. Parameter/Condition Data to clock output skew (at transmitter) Data to clock input skew (at receiver) 2 Clock cycle duration 3 Duty cycle for 1000Base-T 4 Duty cycle for 10BASE-T and 100BASE-TX 3 Rise and fall times Symbol 1 tSKRGT5 tSKRGT tRGT6 tRGTH/tRGT6 tRGTH/tRGT6 tRGTR6,7, tRGTF6,7 Min -500 1.0 7.2 45 40 -- Typ 0 -- 8.0 50 50 -- Max 500 2.8 8.8 55 60 0.75 Unit ps ns ns % % ns Notes: 1. Note that, in general, the clock reference symbol representation for this section is based on the symbols RGT to represent RGMII and RTBI timing. For example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Note also that the notation for rise (R) and fall (F) times follows the clock symbol that is being represented. For symbols representing skews, the subscript is skew (SK) followed by the clock that is being skewed (RGT). 2. The RGMII specification requires that PC board designer add 1.5 ns or greater in trace delay to the RX_CLK in order to meet this specification. However, as stated above, this device will function with only 1.0 ns of delay. 3. For 10 and 100 Mbps, tRGT scales to 400 ns 40 ns and 40 ns 4 ns, respectively. 4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet's clock domains as long as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned between. 5. Guaranteed by characterization. 6. Guaranteed by design. 7. Signal timings are measured at 0.5 V and 2.0 V voltage levels. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 30 Freescale Semiconductor Ethernet: Three-Speed, MII Management Figure 13 shows the RBMII and RTBI AC timing and multiplexing diagrams. tRGT tRGTH GTX_CLK (At Transmitter) tSKRGT TXD[8:5][3:0] TXD[7:4][3:0] TXD[3:0] TXD[8:5] TXD[7:4] TXD[9] TXERR tSKRGT TX_CLK (At PHY) TX_CTL TXD[4] TXEN RXD[8:5][3:0] RXD[7:4][3:0] RXD[8:5] RXD[3:0] RXD[7:4] tSKRGT RXD[4] RXDV RXD[9] RXERR tSKRGT RX_CTL RX_CLK (At PHY) Figure 13. RGMII and RTBI AC Timing and Multiplexing Diagrams 8.3 Ethernet Management Interface Electrical Characteristics The electrical characteristics specified here apply to MII management interface signals MDIO (management data input/output) and MDC (management data clock). The electrical characteristics for GMII, RGMII, TBI and RTBI are specified in Section 8.1, "Three-Speed Ethernet Controller (TSEC) (10/100/1000 Mbps)--GMII/MII/TBI/RGMII/RTBI Electrical Characteristics." 8.3.1 MII Management DC Electrical Characteristics The MDC and MDIO are defined to operate at a supply voltage of 3.3 V. The DC electrical characteristics for MDIO and MDC are provided in Table 27. Table 27. MII Management DC Electrical Characteristics Parameter Supply voltage (3.3 V) Output high voltage Output low voltage Input high voltage Input low voltage Symbol OVDD VOH VOL VIH VIL IOH = -1.0 mA IOL = 1.0 mA -- -- Conditions -- LVDD = Min LVDD = Min Min 3.13 2.10 GND 1.70 -- Max 3.47 LVDD + 0.3 0.50 -- 0.90 Unit V V V V V MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 31 Ethernet: Three-Speed, MII Management Table 27. MII Management DC Electrical Characteristics (continued) Parameter Input high current Input low current Symbol IIH IIL Conditions LVDD = Max LVDD = Max VIN 1 = 2.1 V VIN = 0.5 V Min -- -600 Max 40 -- Unit A A Note: 1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. 8.3.2 MII Management AC Electrical Specifications Table 28. MII Management AC Timing Specifications Table 28 provides the MII management AC timing specifications. At recommended operating conditions with LVDD is 3.3 V 5%. Parameter/Condition MDC frequency MDC period MDC clock pulse width high MDC to MDIO valid MDC to MDIO delay MDIO to MDC setup time MDIO to MDC hold time MDC rise time MDC fall time Symbol 1 fMDC tMDC tMDCH tMDKHDV tMDKHDX tMDDVKH tMDDXKH tMDCR tMDHF Min 0.893 96 32 Typ -- -- -- Max 10.4 1120 -- 2*[1/(fccb_clk/8)] Unit MHz ns ns ns ns ns ns ns ns Notes 2 3 3 10 5 0 -- -- -- -- -- -- -- 2*[1/(fccb_clk/8)] -- -- 10 10 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. This parameter is dependent on the system clock speed (that is, for a system clock of 267 MHz, the delay is 70 ns and for a system clock of 333 MHz, the delay is 58 ns). 3. This parameter is dependent on the CCB clock speed (that is, for a CCB clock of 267 MHz, the delay is 60 ns and for a CCB clock of 333 MHz, the delay is 48 ns). 4. Guaranteed by design. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 32 Freescale Semiconductor Local Bus Figure 14 shows the MII management AC timing diagram. tMDC MDC tMDCH MDIO (Input) tMDDVKH tMDDXKH MDIO (Output) tMDKHDX tMDCF tMDCR Figure 14. MII Management Interface Timing Diagram 9 Local Bus This section describes the DC and AC electrical specifications for the local bus interface of the MPC8555E. 9.1 Local Bus DC Electrical Characteristics Table 29. Local Bus DC Electrical Characteristics Parameter Symbol VIH VIL IIN VOH VOL Test Condition VOUT VOH (min) or VOUT VOL (max) VIN = 0 V or VIN = VDD OVDD = min, IOH = -2mA OVDD = min, IOL = 2mA 1 Table 29 provides the DC electrical characteristics for the local bus interface. Min 2 -0.3 -- OVDD - 0.2 -- Max OVDD + 0.3 0.8 5 -- 0.2 Unit V V A V V High-level input voltage Low-level input voltage Input current High-level output voltage Low-level output voltage Note: 1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 33 Local Bus 9.2 Local Bus AC Electrical Specifications Table 30 describes the general timing parameters of the local bus interface of the MPC8555E with the DLL enabled. Table 30. Local Bus General Timing Parameters - DLL Enabled Parameter Local bus cycle time LCLK[n] skew to LCLK[m] or LSYNC_OUT Input setup to local bus clock (except LUPWAIT) LUPWAIT input setup to local bus clock Input hold from local bus clock (except LUPWAIT) LUPWAIT input hold from local bus clock LALE output transition to LAD/LDP output transition (LATCH hold time) Local bus clock to output valid (except LAD/LDP and LALE) Local bus clock to data valid for LAD/LDP LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) Local bus clock to address valid for LAD LWE[0:1] = 00 LWE[0:1] = 11 (default) Output hold from local bus clock (except LAD/LDP and LALE) Output hold from local bus clock for LAD/LDP Local bus clock to output high Impedance (except LAD/LDP and LALE) LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) tLBKHOZ1 tLBKHOX2 tLBKHOX1 0.7 1.6 0.7 1.6 -- 2.8 4.2 ns 5, 9 -- ns 3, 8 tLBKHOV3 -- tLBKHOV2 -- Configuration 7 Symbol 1 tLBK tLBKSKEW tLBIVKH1 tLBIVKH2 tLBIXKH1 tLBIXKH2 tLBOTOT tLBKHOV1 Min 6.0 -- 1.8 1.7 0.5 1.0 1.5 -- Max -- 150 -- -- -- -- -- 2.3 3.8 2.5 4.0 2.6 4.1 -- ns 3, 8 ns 3, 8 ns 3, 8 Unit ns ps ns ns ns ns ns ns Notes 2 7, 9 3, 4, 8 3, 4 3, 4, 8 3, 4 6 3, 8 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 34 Freescale Semiconductor Local Bus Table 30. Local Bus General Timing Parameters - DLL Enabled (continued) Parameter Local bus clock to output high impedance for LAD/LDP Configuration 7 LWE[0:1] = 00 LWE[0:1] = 11 (default) Symbol 1 tLBKHOZ2 Min -- Max 2.8 4.2 Unit ns Notes 5, 9 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2. All timings are in reference to LSYNC_IN for DLL enabled mode. 3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN for DLL enabled to 0.4 x OVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number of local bus buffer delays used as programmed at power-on reset with configuration pins LWE[0:1]. 7. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at OVDD/2. 8. Guaranteed by characterization. 9. Guaranteed by design. Table 31 describes the general timing parameters of the local bus interface of the MPC8555E with the DLL bypassed. Table 31. Local Bus General Timing Parameters - DLL Bypassed Parameter Local bus cycle time Internal launch/capture clock to LCLK delay LCLK[n] skew to LCLK[m] or LSYNC_OUT Input setup to local bus clock (except LUPWAIT) LUPWAIT input setup to local bus clock Input hold from local bus clock (except LUPWAIT) LUPWAIT input hold from local bus clock LALE output transition to LAD/LDP output transition (LATCH hold time) Local bus clock to output valid (except LAD/LDP and LALE) Local bus clock to data valid for LAD/LDP LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) tLBKLOV2 -- Configuration 7 Symbol 1 tLBK tLBKHKT tLBKSKEW tLBIVKH1 tLBIVKH2 tLBIXKH1 tLBIXKH2 tLBOTOT tLBKLOV1 Min 6.0 1.8 -- 5.2 5.1 -1.3 -0.8 1.5 -- Max -- 3.4 150 -- -- -- -- -- 0.5 2.0 0.7 2.2 ns 3 Unit ns ns ps ns ns ns ns ns ns Notes 2 8 7, 9 3, 4 3, 4 3, 4 3, 4 6 3 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 35 Local Bus Table 31. Local Bus General Timing Parameters - DLL Bypassed (continued) Parameter Local bus clock to address valid for LAD Configuration 7 LWE[0:1] = 00 LWE[0:1] = 11 (default) Output hold from local bus clock (except LAD/LDP and LALE) Output hold from local bus clock for LAD/LDP Local bus clock to output high Impedance (except LAD/LDP and LALE) Local bus clock to output high impedance for LAD/LDP LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) LWE[0:1] = 00 LWE[0:1] = 11 (default) tLBKLOZ2 -- tLBKLOZ1 tLBKLOX2 tLBKLOX1 -2.7 -1.8 -2.7 -1.8 -- 1.0 2.4 1.0 2.4 ns 5 ns 5 -- ns 3 Symbol 1 tLBKLOV3 Min -- Max 0.8 2.3 -- ns 3 Unit ns Notes 3 Notes: 1. The symbols used for timing specifications herein follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing (LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output (O) going invalid (X) or output hold time. 2. All timings are in reference to LSYNC_IN for DLL enabled mode. 3. All signals are measured from OVDD/2 of the rising edge of local bus clock for DLL bypass mode to 0.4 x OVDD of the signal in question for 3.3-V signaling levels. 4. Input timings are measured at the pin. 5. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 6. The value of tLBOTOT is defined as the sum of 1/2 or 1 ccb_clk cycle as programmed by LBCR[AHD], and the number of local bus buffer delays used as programmed at power-on reset with configuration pins LWE[0:1]. 7. Maximum possible clock skew between a clock LCLK[m] and a relative clock LCLK[n]. Skew measured between complementary signals at OVDD/2. 8. Guaranteed by characterization. 9. Guaranteed by design. Figure 15 provides the AC test load for the local bus. Output Z0 = 50 OVDD/2 RL = 50 Figure 15. Local Bus C Test Load MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 36 Freescale Semiconductor Local Bus Figure 16 to Figure 21 show the local bus signals. LSYNC_IN tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIVKH1 Input Signal: LGTA Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKHOV3 Output (Address) Signal: LAD[0:31] tLBOTOT LALE tLBKHOZ2 tLBKHOX2 tLBKHOV1 tLBKHOZ1 tLBKHOX1 tLBIXKH1 tLBIXKH1 tLBKHOV2 tLBKHOZ2 tLBKHOX2 Figure 16. Local Bus Signals, Nonspecial Signals Only (DLL Enabled) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 37 Local Bus Internal launch/capture clock tLBKHKT LCLK[n] tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBIVKH2 Input Signal: LGTA tLBKLOV1 Output Signals: LA[27:31]/LBCTL/LBCKE/LOE/ LSDA10/LSDWE/LSDRAS/ LSDCAS/LSDDQM[0:3] tLBKLOV2 Output (Data) Signals: LAD[0:31]/LDP[0:3] tLBKLOV3 Output (Address) Signal: LAD[0:31] tLBOTOT LALE tLBKLOX2 tLBKLOX1 tLBIXKH2 tLBKLOZ1 tLBIXKH1 tLBKLOZ2 Figure 17. Local Bus Signals, Nonspecial Signals Only (DLL Bypass Mode) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 38 Freescale Semiconductor Local Bus LSYNC_IN T1 T3 tLBKHOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBKHOV1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] tLBKHOZ1 tLBIXKH1 tLBIXKH2 tLBKHOZ1 Figure 18. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Enabled) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 39 Local Bus Internal launch/capture clock T1 T3 tLBKHKT LCLK tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] (DLL Bypass Mode) UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] tLBKLOX1 tLBKLOZ1 tLBIXKH2 tLBIXKH1 Figure 19. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Bypass Mode) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 40 Freescale Semiconductor Local Bus LSYNC_IN T1 T2 T3 T4 tLBKHOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] tLBKHOV1 UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] tLBKHOZ1 tLBIXKH2 tLBKHOZ1 tLBIXKH1 Figure 20. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 or 8 (DLL Enabled) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 41 Local Bus Internal launch/capture clock T1 T2 T3 T4 tLBKHKT LCLK tLBKLOV1 GPCM Mode Output Signals: LCS[0:7]/LWE tLBIVKH2 UPM Mode Input Signal: LUPWAIT tLBIVKH1 Input Signals: LAD[0:31]/LDP[0:3] (DLL Bypass Mode) UPM Mode Output Signals: LCS[0:7]/LBS[0:3]/LGPL[0:5] tLBKLOX1 tLBKLOZ1 tLBIXKH2 tLBIXKH1 Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 or 8 (DLL Bypass Mode) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 42 Freescale Semiconductor CPM 10 CPM This section describes the DC and AC electrical specifications for the CPM of the MPC8555E. 10.1 CPM DC Electrical Characteristics Table 32. CPM DC Electrical Characteristics Characteristic Symbol VIH VIL VOH VOL VOH VOL IOH = -8.0 mA IOL = 8.0 mA IOH = -2.0 mA IOL = 3.2 mA Condition Min 2.0 GND 2.4 -- 2.4 -- Max 3.465 0.8 -- 0.5 -- 0.4 Unit V V V V V V Notes 1 1, 2 1 1 1 1 Table 32 provides the DC electrical characteristics for the CPM. Input high voltage Input low voltage Output high voltage Output low voltage Output high voltage Output low voltage Note: 1. This specification applies to the following pins: PA[0-31], PB[4-31], PC[0-31], and PD[4-31]. 2. VIL(max) for the IIC interface is 0.8 V rather than the 1.5 V specified in the IIC standard 10.2 CPM AC Timing Specifications Table 33. CPM Input AC Timing Specifications 1 Characteristic Symbol 2 tFIIVKH tFIIXKH tFEIVKH tFEIXKHb tNIIVKH tNIIXKH tNEIVKH tNEIXKH tTDIVKH tTDIXKH tPIIVKH Min3 6 0 2.5 2 6 0 4 2 4 3 8 Unit ns ns ns ns ns ns ns ns ns ns ns Table 33 and Table 34 provide the CPM input and output AC timing specifications, respectively. FCC inputs--internal clock (NMSI) input setup time FCC inputs--internal clock (NMSI) hold time FCC inputs--external clock (NMSI) input setup time FCC inputs--external clock (NMSI) hold time SCC/SMC/SPI inputs--internal clock (NMSI) input setup time SCC/SMC/SPI inputs--internal clock (NMSI) input hold time SCC/SMC/SPI inputs--external clock (NMSI) input setup time SCC/SMC/SPI inputs--external clock (NMSI) input hold time TDM inputs/SI--input setup time TDM inputs/SI--hold time PIO inputs--input setup time MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 43 CPM Table 33. CPM Input AC Timing Specifications 1 (continued) Characteristic PIO inputs--input hold time COL width high (FCC) Symbol 2 tPIIXKH tFCCH Min3 1 1.5 Unit ns CLK Notes: 1. Input specifications are measured from the 50% level of the signal to the 50% level of the rising edge of CLKIN. Timings are measured at the pin. 2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tFIIVKH symbolizes the FCC inputs internal timing (FI) with respect to the time the input signals (I) reaching the valid state (V) relative to the reference clock tFCC (K) going to the high (H) state or setup time. And tTDIXKH symbolizes the TDM timing (TD) with respect to the time the input signals (I) reach the invalid state (X) relative to the reference clock tFCC (K) going to the high (H) state or hold time. 3. PIO and TIMER inputs and outputs are asynchronous to SYSCLK or any other externally visible clock. PIO/TIMER inputs are internally synchronized to the CPM internal clock. PIO/TIMER outputs should be treated as asynchronous. Table 34. CPM Output AC Timing Specifications 1 Characteristic FCC outputs--internal clock (NMSI) delay FCC outputs--external clock (NMSI) delay SCC/SMC/SPI outputs--internal clock (NMSI) delay SCC/SMC/SPI outputs--external clock (NMSI) delay TDM outputs/SI delay PIO outputs delay Symbol 2 tFIKHOX tFEKHOX tNIKHOX tNEKHOX tTDKHOX tPIKHOX Min 1 2 0.5 2 2.5 1 Max 5.5 8 10 8 11 11 Unit ns ns ns ns ns ns Notes: 1. Output specifications are measured from the 50% level of the rising edge of CLKIN to the 50% level of the signal. Timings are measured at the pin. 2. The symbols used for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tFIKHOX symbolizes the FCC inputs internal timing (FI) for the time tFCC memory clock reference (K) goes from the high state (H) until outputs (O) are invalid (X). Figure 22 provides the AC test load for the CPM. Output Z0 = 50 OVDD/2 RL = 50 Figure 22. CPM AC Test Load Figure 23 through Figure 29 represent the AC timing from Table 33 and Table 34. Note that although the specifications generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge is the active edge. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 44 Freescale Semiconductor CPM Figure 23 shows the FCC internal clock. BRG_OUT tFIIVKH FCC Input Signals tFIKHOX FCC Output Signals (When GFMR TCI = 0) tFIKHOX FCC Output Signals (When GFMR TCI = 1) tFIIXKH Figure 23. FCC Internal AC Timing Clock Diagram Figure 24 shows the FCC external clock. Serial CLKIN tFEIVKH FCC Input Signals tFEKHOX FCC Output Signals (When GFMR TCI = 0) tFEKHOX FCC Output Signals (When GFMR TCI = 1) tFEIXKH Figure 24. FCC External AC Timing Clock Diagram Figure 25 shows Ethernet collision timing on FCCs. COL (Input) tFCCH Figure 25. Ethernet Collision AC Timing Diagram (FCC) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 45 CPM Figure 26 shows the SCC/SMC/SPI 1,2external clock. Serial CLKIN tNEIVKH tNEIXKH Input Signals: SCC/SMC/SPI (See Note) Output Signals: SCC/SMC/SPI (See Note) tNEKHOX Note: The clock edge is selectable on SCC and SPI. Figure 26. SCC/SMC/SPI AC Timing External Clock Diagram Figure 27 shows the SCC/SMC/SPI 1,2 internal clock. BRG_OUT tNIIVKH tNIIXKH Input Signals: SCC/SMC/SPI (See Note) Output Signals: SCC/SMC/SPI (See Note) tNIKHOX Note: The clock edge is selectable on SCC and SPI. Figure 27. SCC/SMC/SPI AC Timing Internal Clock Diagram Figure 28 shows TDM input and output signals. Serial CLKIN tTDIVKH TDM Input Signals tTDKHOX TDM Output Signals Note: There are 4 possible TDM timing conditions: 1. Input sampled on the rising edge and output driven on the rising edge (shown). 2. Input sampled on the rising edge and output driven on the falling edge. 3. Input sampled on the falling edge and output driven on the falling edge. 4. Input sampled on the falling edge and output driven on the rising edge. tTDIXKH Figure 28. TDM Signal AC Timing Diagram 1 SPI AC timings are internal mode when it is master since SPICLK is an output, and external mode when it is slave. SPI AC timings refer always to SPICLK. 2 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 46 Freescale Semiconductor CPM Sys clk tPIIVKH PIO inputs tPIIXKH tPIKHOX PIO outputs Figure 29. PIO Signal Diagram 10.3 CPM I2C AC Specification Table 35. I2C Timing Characteristic Expression fSCL fSCL tSDHDL tSCLCH tSCHCL tSCHDL tSDLCL tSCLDX tSDVCH tSRISE tSFALL tSCHDH All Frequencies Min 0 BRGCLK/16512 1/(2.2 * fSCL) 1/(2.2 * fSCL) 1/(2.2 * fSCL) 2/(divider * fSCL) 3/(divider * fSCL) 2/(divider * fSCL) 3/(divider * fSCL) 2/(divider * fSCL) Max FMAX(1) BRGCLK/48 - (2) 1/(10 * fSCL) 1/(33 * fSCL) Unit Hz Hz s s s s s s s s s s SCL clock frequency (slave) SCL clock frequency (master) Bus free time between transmissions Low period of SCL High period of SCL Start condition setup time2 Start condition hold time2 Data hold time 2 Data setup time2 SDA/SCL rise time SDA/SCL fall time Stop condition setup time Notes: 1. FMAX = BRGCLK/(min_divider*prescale. Where prescaler=25-I2MODE[PDIV]; and min_divider=12 if digital filter disabled and 18 if enabled. Example #1: if I2MODE[PDIV]=11 (prescaler=4) and I2MODE[FLT]=0 (digital filter disabled) then FMAX=BRGCLK/48 Example #2: if I2MODE[PDIV]=00 (prescaler=32) and I2MODE[FLT]=1 (digital filter enabled) then FMAX=BRGCLK/576 2. divider = fSCL/prescaler. In master mode: divider=BRGCLK/(fSCL*prescaler)=2*(I2BRG[DIV]+3) In slave mode: divider=BRGCLK/(fSCL*prescaler) MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 47 CPM SDA tSDHDL tSCHDL SCL tSDLCL tSRISE tSFALL tSCHDH tSCLCH tSCLDX tSCHCL tSDVCH Figure 30. CPM I2C Bus Timing Diagram The following two tables are examples of I2C AC parameters at I2C clock value of 100k and 400k respectively. Table 36. CPM I2C Timing (fSCL=100KHz) Frequency = 100KHz Characteristic SCL clock frequency (slave) SCL clock frequency (master) Bus free time between transmissions Low period of SCL High period of SCL Start condition setup time Start condition hold time Data hold time Data setup time SDA/SCL rise time SDA/SCL fall time (master) Stop condition setup time Expression Min fSCL fSCL tSDHDL tSCLCH tSCHCL tSCHDL tSDLCL tSCLDX tSDVCH tSRISE tSFALL tSCHDH 4.7 4.7 4 2 3 2 3 2 Max 100 100 1 303 KHz KHz s s s s s s s s ns s Unit Table 37. CPM I2C Timing (fSCL=400KHz) Frequency = 400KHz Characteristic SCL clock frequency (slave) SCL clock frequency (master) Bus free time between transmissions Low period of SCL High period of SCL Start condition setup time Start condition hold time Data hold time Data setup time SDA/SCL rise time SDA/SCL fall time Stop condition setup time Expression Min fSCL fSCL tSDHDL tSCLCH tSCHCL tSCHDL tSDLCL tSCLDX tSDVCH tSRISE tSFALL tSCHDH 1.2 1.2 1 420 630 420 630 420 Max 400 400 250 75 KHz KHz s s s ns ns ns ns ns ns ns Unit MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 48 Freescale Semiconductor JTAG 11 JTAG This section describes the AC electrical specifications for the IEEE 1149.1 (JTAG) interface of the MPC8555E. Table 38 provides the JTAG AC timing specifications as defined in Figure 32 through Figure 35. Table 38. JTAG AC Timing Specifications (Independent of SYSCLK) 1 At recommended operating conditions (see Table 2). Parameter JTAG external clock frequency of operation JTAG external clock cycle time JTAG external clock pulse width measured at 1.4 V JTAG external clock rise and fall times TRST assert time Input setup times: Boundary-scan data TMS, TDI Input hold times: Boundary-scan data TMS, TDI Valid times: Boundary-scan data TDO Output hold times: Boundary-scan data TDO JTAG external clock to output high impedance: Boundary-scan data TDO Symbol 2 fJTG t JTG tJTKHKL tJTGR & tJTGF tTRST tJTDVKH tJTIVKH tJTDXKH tJTIXKH tJTKLDV tJTKLOV tJTKLDX tJTKLOX tJTKLDZ tJTKLOZ Min 0 30 15 0 25 4 0 20 25 4 4 -- -- 3 3 Max 33.3 -- -- 2 -- -- -- Unit MHz ns ns ns ns ns Notes 3 4 ns -- -- ns 20 25 ns -- -- ns 19 9 5, 6 5 5 4 Notes: 1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question. The output timings are measured at the pins. All output timings assume a purely resistive 50- load (see Figure 31). Time-of-flight delays must be added for trace lengths, vias, and connectors in the system. 2. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing (JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D) went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. Note that, in general, the clock reference symbol representation is based on three letters representing the clock of a particular functional. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only. 4. Non-JTAG signal input timing with respect to tTCLK. 5. Non-JTAG signal output timing with respect to tTCLK. 6. Guaranteed by design. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 49 JTAG Figure 31 provides the AC test load for TDO and the boundary-scan outputs of the MPC8555E. Output Z0 = 50 OVDD/2 RL = 50 Figure 31. AC Test Load for the JTAG Interface Figure 32 provides the JTAG clock input timing diagram. JTAG External Clock VM tJTKHKL tJTG VM = Midpoint Voltage (OVDD/2) VM VM tJTGR tJTGF Figure 32. JTAG Clock Input Timing Diagram Figure 33 provides the TRST timing diagram. TRST VM tTRST VM = Midpoint Voltage (OVDD/2) VM Figure 33. TRST Timing Diagram Figure 34 provides the boundary-scan timing diagram. JTAG External Clock VM tJTDVKH tJTDXKH Boundary Data Inputs tJTKLDV tJTKLDX Boundary Data Outputs tJTKLDZ Boundary Data Outputs Output Data Valid VM = Midpoint Voltage (OVDD/2) Output Data Valid Input Data Valid VM Figure 34. Boundary-Scan Timing Diagram MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 50 Freescale Semiconductor I2C Figure 35 provides the test access port timing diagram. JTAG External Clock VM tJTIVKH tJTIXKH TDI, TMS tJTKLOV tJTKLOX TDO tJTKLOZ TDO Output Data Valid VM = Midpoint Voltage (OVDD/2) Output Data Valid Input Data Valid VM Figure 35. Test Access Port Timing Diagram 12 I2C This section describes the DC and AC electrical characteristics for the I2C interface of the MPC8555E. 12.1 I2C DC Electrical Characteristics Table 39. I2C DC Electrical Characteristics Table 39 provides the DC electrical characteristics for the I2C interface of the MPC8555E. At recommended operating conditions with OVDD of 3.3 V 5%. Parameter Input high voltage level Input low voltage level Low level output voltage Output fall time from VIH(min) to VIL(max) with a bus capacitance from 10 to 400 pF Pulse width of spikes which must be suppressed by the input filter Input current each I/O pin (input voltage is between 0.1 x OVDD and 0.9 x OVDD(max) Capacitance for each I/O pin Symbol VIH VIL VOL tI2KLKV tI2KHKL II CI Min 0.7 x OVDD -0.3 0 20 + 0.1 x CB 0 -10 -- Max OVDD+ 0.3 0.3 x OVDD 0.2 x OVDD 250 50 10 10 Unit V V V ns ns A pF Notes 1 2 3 4 Notes: 1. Output voltage (open drain or open collector) condition = 3 mA sink current. 2. CB = capacitance of one bus line in pF. 3. Refer to the MPC8555E PowerQUICCTM III Integrated Communications Processor Reference Manual for information on the digital filter used. 4. I/O pins will obstruct the SDA and SCL lines if OVDD is switched off. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 51 I2C 12.2 I2C AC Electrical Specifications Table 40. I2C AC Electrical Specifications Table 40 provides the AC timing parameters for the I2C interface of the MPC8555E. All values refer to VIH (min) and VIL (max) levels (see Table 39). Parameter SCL clock frequency Low period of the SCL clock High period of the SCL clock Setup time for a repeated START condition Hold time (repeated) START condition (after this period, the first clock pulse is generated) Data setup time Data hold time: CBUS compatible masters I2C bus devices Rise time of both SDA and SCL signals Fall time of both SDA and SCL signals Set-up time for STOP condition Bus free time between a STOP and START condition Noise margin at the LOW level for each connected device (including hysteresis) Noise margin at the HIGH level for each connected device (including hysteresis) Symbol 1 fI2C tI2CL6 tI2CH6 tI2SVKH6 tI2SXKL6 tI2DVKH6 tI2DXKL Min 0 1.3 0.6 0.6 0.6 100 -- 02 Max 400 -- -- -- -- -- -- 0.9 3 300 300 -- -- -- -- Unit kHz s s s s ns s tI2CR 20 + 0.1 Cb 4 20 + 0.1 Cb 4 0.6 1.3 0.1 x OVDD 0.2 x OVDD ns ns s s V V tI2CF tI2PVKH tI2KHDX VNL VNH Notes: 1. The symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition (S) went invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes I2C timing (I2) for the time that the data with respect to the stop condition (P) reaching the valid state (V) relative to the tI2C clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). 2. MPC8555E provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge the undefined region of the falling edge of SCL. 3. The maximum tI2DVKH has only to be met if the device does not stretch the LOW period (tI2CL) of the SCL signal. 4. CB = capacitance of one bus line in pF. 5. Guaranteed by design. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 52 Freescale Semiconductor PCI Figure 15 provides the AC test load for the I2C. Output Z0 = 50 OVDD/2 RL = 50 Figure 36. I2C AC Test Load Figure 37 shows the AC timing diagram for the I2C bus. SDA tI2CF tI2CL SCL tI2SXKL S tI2DXKL tI2CH Sr tI2SVKH tI2PVKH P S tI2DVKH tI2SXKL tI2KHKL tI2CR tI2CF Figure 37. I2C Bus AC Timing Diagram 13 PCI This section describes the DC and AC electrical specifications for the PCI bus of the MPC8555E. 13.1 PCI DC Electrical Characteristics Table 41. PCI DC Electrical Characteristics 1 Parameter Symbol VIH VIL IIN VOH VOL Test Condition VOUT VOH (min) or VOUT VOL (max) VIN = 0 V or VIN = VDD OVDD = min, IOH = -100 A OVDD = min, IOL = 100 A 2 Table 41 provides the DC electrical characteristics for the PCI interface of the MPC8555E. Min 2 -0.3 -- OVDD - 0.2 -- Max OVDD + 0.3 0.8 5 -- 0.2 Unit V V A V V High-level input voltage Low-level input voltage Input current High-level output voltage Low-level output voltage Notes: 1. Ranges listed do not meet the full range of the DC specifications of the PCI 2.2 Local Bus Specifications. 2. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 53 PCI 13.2 PCI AC Electrical Specifications This section describes the general AC timing parameters of the PCI bus of the MPC8555E. Note that the SYSCLK signal is used as the PCI input clock. Table 42 provides the PCI AC timing specifications at 66 MHz. NOTE PCI Clock can be PCI1_CLK or SYSCLK based on POR config input. NOTE The input setup time does not meet the PCI specification. Table 42. PCI AC Timing Specifications at 66 MHz Parameter Clock to output valid Output hold from Clock Clock to output high impedance Input setup to Clock Input hold from Clock REQ64 to HRESET 9 setup time HRESET to REQ64 hold time HRESET high to first FRAME assertion Symbol 1 tPCKHOV Min -- 2.0 -- 3.3 0 10 x tSYS 0 10 Max 6.0 -- 14 -- -- -- 50 -- Unit ns ns ns ns ns clocks ns clocks Notes 2, 3 2, 9 2, 3, 10 2, 4, 9 2, 4, 9 5, 6, 10 6, 10 7, 10 tPCKHOX tPCKHOZ tPCIVKH tPCIXKH tPCRVRH tPCRHRX tPCRHFV Notes: 1. Note that the symbols used for timing specifications herein follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the SYSCLK clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state. 2. See the timing measurement conditions in the PCI 2.2 Local Bus Specifications. 3. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the component pin is less than or equal to the leakage current specification. 4. Input timings are measured at the pin. 5. The timing parameter tSYS indicates the minimum and maximum CLK cycle times for the various specified frequencies. The system clock period must be kept within the minimum and maximum defined ranges. For values see Section 15, "Clocking." 6. The setup and hold time is with respect to the rising edge of HRESET. 7. The timing parameter tPCRHFV is a minimum of 10 clocks rather than the minimum of 5 clocks in the PCI 2.2 Local Bus Specifications. 8. The reset assertion timing requirement for HRESET is 100 s. 9. Guaranteed by characterization. 10.Guaranteed by design. Figure 15 provides the AC test load for PCI. Output Z0 = 50 OVDD/2 RL = 50 Figure 38. PCI AC Test Load MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 54 Freescale Semiconductor Package and Pin Listings Figure 39 shows the PCI input AC timing conditions. CLK tPCIVKH tPCIXKH Input Figure 39. PCI Input AC Timing Measurement Conditions Figure 40 shows the PCI output AC timing conditions. CLK tPCKHOV Output Delay tPCKHOZ High-Impedance Output Figure 40. PCI Output AC Timing Measurement Condition 14 Package and Pin Listings This section details package parameters, pin assignments, and dimensions. 14.1 Package Parameters for the MPC8555E FC-PBGA The package parameters are as provided in the following list. The package type is 29 mm x 29 mm, 783 flip chip plastic ball grid array (FC-PBGA). Die size 8.7 mm x 9.3 mm x 0.75 mm Package outline 29 mm x 29 mm Interconnects 783 Pitch 1 mm Minimum module height Maximum module height Solder Balls Ball diameter (typical) 3.07 mm 3.75 mm 62 Sn/36 Pb/2 Ag 0.5 mm MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 55 Package and Pin Listings 14.2 Mechanical Dimensions of the FC-PBGA Figure 41 the mechanical dimensions and bottom surface nomenclature of the MPC8555E 783 FC-PBGA package. Figure 41. Mechanical Dimensions and Bottom Surface Nomenclature of the FC-PBGA NOTES 1. All dimensions are in millimeters. 2. Dimensions and tolerances per ASME Y14.5M-1994. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 56 Freescale Semiconductor Package and Pin Listings 3. 4. 5. 6. 7. Maximum solder ball diameter measured parallel to datum A. Datum A, the seating plane, is defined by the spherical crowns of the solder balls. Capacitors may not be present on all devices. Caution must be taken not to short capacitors or exposed metal capacitor pads on package top. The socket lid must always be oriented to A1. 14.3 Pinout Listings Table 43. MPC8555E Pinout Listing Signal Package Pin Number PCI1 and PCI2 (one 64-bit or two 32-bit) Pin Type Power Supply Notes Table 44 provides the pin-out listing for the MPC8555E, 783 FC-PBGA package. PCI1_AD[63:32], PCI2_AD[31:0] AA14, AB14, AC14, AD14, AE14, AF14, AG14, AH14, V15, W15, Y15, AA15, AB15, AC15, AD15, AG15, AH15, V16, W16, AB16, AC16, AD16, AE16, AF16, V17, W17, Y17, AA17, AB17, AE17, AF17, AF18 AH6, AD7, AE7, AH7, AB8, AC8, AF8, AG8, AD9, AE9, AF9, AG9, AH9, W10, Y10, AA10, AE11, AF11, AG11, AH11, V12, W12, Y12, AB12, AD12, AE12, AG12, AH12, V13, Y13, AB13, AC13 AG13, AH13, V14, W14 AH8, AB10, AD11, AC12 AA11 Y14 AC10 AG10 AD10 V11 AH10 AA9 AE13 I/O OVDD 17 PCI1_AD[31:0] I/O OVDD 17 PCI_C_BE64[7:4] PCI2_C_BE[3:0] PCI_C_BE64[3:0] PCI1_C_BE[3:0] PCI1_PAR PCI1_PAR64/PCI2_PAR PCI1_FRAME PCI1_TRDY PCI1_IRDY PCI1_STOP PCI1_DEVSEL PCI1_IDSEL PCI1_REQ64/PCI2_FRAME I/O I/O I/O I/O I/O I/O I/O I/O I/O I I/O I/O I/O I/O I/O I OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD 17 17 2 2 2 2 2 5, 10 2 2 2, 4 PCI1_ACK64/PCI2_DEVSEL AD13 PCI1_PERR PCI1_SERR PCI1_REQ[0] PCI1_REQ[1:4] W11 Y11 AF5 AF3, AE4, AG4, AE5 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 57 Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal PCI1_GNT[0] PCI1_GNT[1:4] PCI1_CLK PCI2_CLK PCI2_GNT[0] PCI2_GNT[1:4] PCI2_IDSEL PCI2_IRDY PCI2_PERR PCI2_REQ[0] PCI2_REQ[1:4] PCI2_SERR PCI2_STOP PCI2_TRDY AE6 AG5, AH5, AF6, AG6 AH25 AH27 AC18 AD18, AE18, AE19, AD19 AC22 AD20 AC20 AD21 AE21, AD22, AE22, AC23 AE20 AC21 AC19 DDR SDRAM Memory Interface MDQ[0:63] M26, L27, L22, K24, M24, M23, K27, K26, K22, J28, F26, E27, J26, J23, H26, G26, C26, E25, C24, E23, D26, C25, A24, D23, B23, F22, J21, G21, G22, D22, H21, E21, N18, J18, D18, L17, M18, L18, C18, A18, K17, K16, C16, B16, G17, L16, A16, L15, G15, E15, C14, K13, C15, D15, E14, D14, D13, E13, D12, A11, F13, H13, A13, B12 N20, M20, L19, E19, C21, A21, G19, A19 L24, H28, F24, L21, E18, E16, G14, B13, M19 L26, J25, D25, A22, H18, F16, F14, C13, C20 B18, B19 N19, B21, F21, K21, M21, C23, A23, B24, H23, G24, K19, B25, D27, J14, J13 D17 F17 J16 H16, G16, J15, H15 E26, E28 J20, H25, A15, D20, F28, K14 F20, G27, B15, E20, F27, L14 I/O GVDD Package Pin Number Pin Type I/O O I I I/O O I I/O I/O I/O I I/O I/O I/O Power Supply OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD 2,4 2 2 2 2 5, 9 5, 9 Notes MECC[0:7] MDM[0:8] MDQS[0:8] MBA[0:1] MA[0:14] MWE MRAS MCAS MCS[0:3] MCKE[0:1] MCK[0:5] MCK[0:5] I/O O I/O O O O O O O O O O GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD GVDD 11 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 58 Freescale Semiconductor Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal MSYNC_IN MSYNC_OUT M28 N28 Local Bus Controller Interface LA[27] LA[28:31] LAD[0:31] U18 T18, T19, T20, T21 AD26, AD27, AD28, AC26, AC27, AC28, AA22, AA23, AA26, Y21, Y22, Y26, W20, W22, W26, V19, T22, R24, R23, R22, R21, R18, P26, P25, P20, P19, P18, N22, N23, N24, N25, N26 V21 V20 U23 U27, U28, V18 Y27, Y28, W27, W28, R27 R28 P27 P28 AA27, AA28, T26, P21 U19 U22 V28 V27 V23 V22 T27 T28 AB28, AB27 T23, P24 O O I/O OVDD OVDD OVDD 5, 9 5, 7, 9 Package Pin Number Pin Type I O Power Supply GVDD GVDD Notes 22 22 LALE LBCTL LCKE LCLK[0:2] LCS[0:4] LCS5/DMA_DREQ2 LCS6/DMA_DACK2 LCS7/DMA_DDONE2 LDP[0:3] LGPL0/LSDA10 LGPL1/LSDWE LGPL2/LOE/LSDRAS LGPL3/LSDCAS LGPL4/LGTA/LUPWAIT/ LPBSE LGPL5 LSYNC_IN LSYNC_OUT LWE[0:1]/LSDDQM[0:1]/ LBS[0:1] LWE[2:3]/LSDDQM[2:3]/ LBS[2:3] O O O O O I/O O O I/O O O O O I/O O I O O O OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD 5, 8, 9 9 1 1 1 5, 9 5, 9 5, 8, 9 5, 9 21 5, 9 1, 5, 9 1, 5, 9 DMA DMA_DREQ[0:1] DMA_DACK[0:1] H5, G4 H6, G5 I O OVDD OVDD MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 59 Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal DMA_DDONE[0:1] H7, G6 Programmable Interrupt Controller MCP UDE IRQ[0:7] IRQ8 IRQ9/DMA_DREQ3 IRQ10/DMA_DACK3 IRQ11/DMA_DDONE3 IRQ_OUT AG17 AG16 AA18, Y18, AB18, AG24, AA21, Y19, AA19, AG25 AB20 Y20 AF26 AH24 AB21 Ethernet Management Interface EC_MDC EC_MDIO F1 E1 Gigabit Reference Clock EC_GTX_CLK125 E2 Three-Speed Ethernet Controller (Gigabit Ethernet 1) TSEC1_TXD[7:4] TSEC1_TXD[3:0] TSEC1_TX_EN TSEC1_TX_ER TSEC1_TX_CLK TSEC1_GTX_CLK TSEC1_CRS TSEC1_COL TSEC1_RXD[7:0] TSEC1_RX_DV TSEC1_RX_ER TSEC1_RX_CLK A6, F7, D7, C7 B7, A7, G8, E8 C8 B8 C6 B6 C3 G7 D4, B4, D3, D5, B5, A5, F6, E6 D2 E5 D6 Three-Speed Ethernet Controller (Gigabit Ethernet 2) TSEC2_TXD[7:4] TSEC2_TXD[3:0] B10, A10, J10, K11 J11, H11, G11, E11 O O LVDD LVDD 5, 9, 18 O O O O I O I I I I I I LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD 9, 18 11 I LVDD O I/O OVDD OVDD 5, 9 I I I I I I/O I/O O OVDD OVDD OVDD OVDD OVDD OVDD OVDD OVDD 9 1 1 1 2, 4 Package Pin Number Pin Type O Power Supply OVDD Notes MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 60 Freescale Semiconductor Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal TSEC2_TX_EN TSEC2_TX_ER TSEC2_TX_CLK TSEC2_GTX_CLK TSEC2_CRS TSEC2_COL TSEC2_RXD[7:0] TSEC2_RX_DV TSEC2_RX_ER TSEC2_RX_CLK B11 D11 D10 C10 D9 F8 F9, E9, C9, B9, A9, H9, G10, F10 H8 A8 E10 DUART UART_CTS[0,1] UART_RTS[0,1] UART_SIN[0,1] UART_SOUT[0,1] Y2, Y3 Y1, AD1 P11, AD5 N6, AD2 I2C interface IIC_SDA IIC_SCL AH22 AH23 System Control HRESET HRESET_REQ SRESET CKSTP_IN CKSTP_OUT AH16 AG20 AF20 M11 G1 Debug TRIG_IN TRIG_OUT/READY MSRCID[0:1] MSRCID[2:3] MSRCID4 MDVAL N12 G2 J9, G3 F3, F5 F2 F4 I O O O O O OVDD OVDD OVDD OVDD OVDD OVDD 6, 9, 18 5, 6, 9 6 6 6 I O I I O OVDD OVDD OVDD OVDD OVDD 2, 4 18 I/O I/O OVDD OVDD 4, 19 4, 19 I O I O OVDD OVDD OVDD OVDD Package Pin Number Pin Type O O I O I I I I I I Power Supply LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD LVDD Notes 11 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 61 Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal Package Pin Number Clock SYSCLK RTC CLK_OUT AH21 AB23 AF22 JTAG TCK TDI TDO TMS TRST AF21 AG21 AF19 AF23 AG23 DFT LSSD_MODE L1_TSTCLK L2_TSTCLK TEST_SEL0 TEST_SEL1 AG19 AB22 AG22 AH20 AG26 Thermal Management THERM0 THERM1 AG2 AH3 Power Management ASLEEP AG18 Power and Ground Signals AVDD1 AVDD2 AVDD3 AVDD4 AVDD5 AH19 AH18 AH17 AF28 AE28 Power for e500 PLL (1.2 V) Power for CCB PLL (1.2 V) Power for CPM PLL (1.2 V) Power for PCI1 PLL (1.2 V) Power for PCI2 PLL (1.2 V) AVDD1 AVDD2 AVDD3 AVDD4 AVDD5 9, 18 -- -- -- -- 14 14 I I I I I OVDD OVDD OVDD OVDD OVDD 20 20 20 3 3 I I O I I OVDD OVDD OVDD OVDD OVDD 12 11 12 12 I I O OVDD OVDD OVDD Pin Type Power Supply Notes MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 62 Freescale Semiconductor Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal GND Package Pin Number A12, A17, B3, B14, B20, B26, B27, C2, C4, C11,C17, C19, C22, C27, D8, E3, E12, E24, F11, F18, F23, G9, G12, G25, H4, H12, H14, H17, H20, H22, H27, J19, J24, K5, K9, K18, K23, K28, L6, L20, L25, M4, M12, M14, M16, M22, M27, N2, N13, N15, N17, P12, P14, P16, P23, R13, R15, R17, R20, R26, T3, T8, T10, T12, T14, T16, U6, U13, U15, U16, U17, U21, V7, V10, V26, W5, W18, W23, Y8, Y16, AA6, AA13, AB4, AB11, AB19, AC6, AC9, AD3, AD8, AD17, AF2, AF4, AF10, AF13, AF15, AF27, AG3, AG7 Pin Type -- Power Supply -- Notes GVDD A14, A20, A25, A26, A27, A28, B17, B22, B28, C12, Power for DDR C28, D16, D19, D21, D24, D28, E17, E22, F12, F15, DRAM I/O F19, F25, G13, G18, G20, G23, G28, H19, H24, J12, Voltage J17, J22, J27, K15, K20, K25, L13, L23, L28, M25, (2.5 V) N21 A4, C5, E7, H10 Reference Voltage; Three-Speed Ethernet I/O (2.5 V, 3.3 V) Reference Voltage Signal; DDR -- GVDD LVDD LVDD MVREF N27 MVREF No Connects AA24, AA25, AA3, AA4, AA7 AA8, AB24, AB25, AC24, AC25, AD23, AD24, AD25, AE23, AE24, AE25, AE26, AE27, AF24, AF25, H1, H2, J1, J2, J3, J4, J5, J6, M1, N1, N10, N11, N4, N5, N7, N8, N9, P10, P8, P9, R10, R11, T24, T25, U24, U25, V24, V25, W24, W25, W9, Y24, Y25, Y5, Y6, Y9, AH26, AH28, AG28, AH1, AG1, AH2, B1, B2, A2, A3 -- 16 OVDD D1, E4, H3, K4, K10, L7, M5, N3, P22, R19, R25, T2, PCI, 10/100 T7, U5, U20, U26, V8, W4, W13, W19, W21, Y7, Y23, Ethernet, and AA5, AA12, AA16, AA20, AB7, AB9, AB26, AC5, other Standard AC11, AC17, AD4, AE1, AE8, AE10, AE15, AF7, (3.3 V) AF12, AG27, AH4 C1, T11, U11, AF1 L12 K12 -- Power for Core (1.2 V) -- OVDD RESERVED SENSEVDD SENSEVSS VDD -- VDD -- VDD 15 13 13 M13, M15, M17, N14, N16, P13, P15, P17, R12, R14, Power for Core R16, T13, T15, T17, U12, U14 (1.2 V) CPM PA[8:31] J7, J8, K8, K7, K6, K3, K2, K1, L1, L2, L3, L4, L5, L8, L9, L10, L11, M10, M9, M8, M7, M6, M3, M2 I/0 OVDD MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 63 Package and Pin Listings Table 43. MPC8555E Pinout Listing (continued) Signal PB[18:31] PC[0, 1, 4-29] Package Pin Number P7, P6, P5, P4, P3, P2, P1, R1, R2, R3, R4, R5, R6, R7 R8, R9, T9, T6, T5, T4, T1, U1, U2, U3, U4, U7, U8, U9, U10, V9, V6, V5, V4, V3, V2, V1, W1, W2, W3, W6, W7, W8 Y4, AA2, AA1, AB1, AB2, AB3, AB5, AB6, AC7, AC4, AC3, AC2, AC1, AD6, AE3, AE2 Pin Type I/0 I/0 Power Supply OVDD OVDD Notes PD[7, 14-25, 29-31] I/0 OVDD Notes: 1. All multiplexed signals are listed only once and do not re-occur. For example, LCS5/DMA_REQ2 is listed only once in the Local Bus Controller Interface section, and is not mentioned in the DMA section even though the pin also functions as DMA_REQ2. 2. Recommend a weak pull-up resistor (2-10 k) be placed on this pin to OVDD. 3. TEST_SEL0 must be pulled-high, TEST_SEL1 must be tied to ground. 4. This pin is an open drain signal. 5. This pin is a reset configuration pin. It has a weak internal pull-up P-FET which is enabled only when the MPC8555E is in the reset state. This pull-up is designed such that it can be overpowered by an external 4.7-k pull-down resistor. If an external device connected to this pin might pull it down during reset, then a pull-up or active driver is needed if the signal is intended to be high during reset. 6. Treat these pins as no connects (NC) unless using debug address functionality. 7. The value of LA[28:31] during reset sets the CCB clock to SYSCLK PLL ratio. These pins require 4.7-k pull-up or pull-down resistors. See Section 15.2, "Platform/System PLL Ratio." 8. The value of LALE and LGPL2 at reset set the e500 core clock to CCB Clock PLL ratio. These pins require 4.7-k pull-up or pull-down resistors. See the Section 15.3, "e500 Core PLL Ratio." 9. Functionally, this pin is an output, but structurally it is an I/O because it either samples configuration input during reset or because it has other manufacturing test functions. This pin will therefore be described as an I/O for boundary scan. 10.This pin functionally requires a pull-up resistor, but during reset it is a configuration input that controls 32- vs. 64-bit PCI operation. Therefore, it must be actively driven low during reset by reset logic if the device is to be configured to be a 64-bit PCI device. Refer to the PCI Specification. 11.This output is actively driven during reset rather than being three-stated during reset. 12.These JTAG pins have weak internal pull-up P-FETs that are always enabled. 13.These pins are connected to the VDD/GND planes internally and may be used by the core power supply to improve tracking and regulation. 14.Internal thermally sensitive resistor. 15.No connections should be made to these pins. 16.These pins are not connected for any functional use. 17.PCI specifications recommend that a weak pull-up resistor (2-10 k) be placed on the higher order pins to OVDD when using 64-bit buffer mode (pins PCI_AD[63:32] and PCI2_C_BE[7:4]). 18. If this pin is connected to a device that pulls down during reset, an external pull-up is required to that is strong enough to pull this signal to a logic 1 during reset. 19. Recommend a pull-up resistor (~1 k) be placed on this pin to OVDD. 20. These are test signals for factory use only and must be pulled up (100 1k) to OVDD for normal machine operation. 21. If this signal is used as both an input and an output, a weak pull-up (~10k) is required on this pin. 22. MSYNC_IN and MSYNC_OUT should be connected together for proper operation. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 64 Freescale Semiconductor Clocking 15 Clocking This section describes the PLL configuration of the MPC8555E. Note that the platform clock is identical to the CCB clock. 15.1 Clock Ranges Table 44 provides the clocking specifications for the processor core and Table 45 provides the clocking specifications for the memory bus. Table 44. Processor Core Clocking Specifications Maximum Processor Core Frequency Characteristic 533 MHz Min e500 core processor frequency 400 Max 533 600 MHz Min 400 Max 600 667 MHz Min 400 Max 667 833 MHz Min 400 Max 833 1000 MHz Min 400 Max 1000 MHz 1, 2, 3 Unit Notes Notes: 1. Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 15.2, "Platform/System PLL Ratio," and Section 15.3, "e500 Core PLL Ratio," for ratio settings. 2.)The minimum e500 core frequency is based on the minimum platform frequency of 200 MHz. 3. 1000 MHz frequency supports only a 1.3 V core. Table 45. Memory Bus Clocking Specifications Maximum Processor Core Frequency Characteristic 533, 600, 667, 883, 1000 MHz Min Memory bus frequency 100 Max 166 MHz 1, 2, 3 Unit Notes Notes: 1. Caution: The CCB to SYSCLK ratio and e500 core to CCB ratio settings must be chosen such that the resulting SYSCLK frequency, e500 (core) frequency, and CCB frequency do not exceed their respective maximum or minimum operating frequencies. Refer to Section 15.2, "Platform/System PLL Ratio," and Section 15.3, "e500 Core PLL Ratio," for ratio settings. 2. The memory bus speed is half of the DDR data rate, hence, half of the platform clock frequency. 3. 1000 MHz frequency supports only a 1.3 V core. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 65 Clocking 15.2 Platform/System PLL Ratio The platform clock is the clock that drives the L2 cache, the DDR SDRAM data rate, and the e500 core complex bus (CCB), and is also called the CCB clock. The values are determined by the binary value on LA[28:31] at power up, as shown in Table 46. There is no default for this PLL ratio; these signals must be pulled to the desired values. For specifications on the PCI_CLK, refer to the PCI 2.2 Specification. Table 46. CCB Clock Ratio Binary Value of LA[28:31] Signals 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Ratio Description 16:1 ratio CCB clock: SYSCLK (PCI bus) Reserved 2:1 ratio CCB clock: SYSCLK (PCI bus) 3:1 ratio CCB clock: SYSCLK (PCI bus) 4:1 ratio CCB clock: SYSCLK (PCI bus) 5:1 ratio CCB clock: SYSCLK (PCI bus) 6:1 ratio CCB clock: SYSCLK (PCI bus) Reserved 8:1 ratio CCB clock: SYSCLK (PCI bus) 9:1 ratio CCB clock: SYSCLK (PCI bus) 10:1 ratio CCB clock: SYSCLK (PCI bus) Reserved 12:1 ratio CCB clock: SYSCLK (PCI bus) Reserved Reserved Reserved MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 66 Freescale Semiconductor Clocking 15.3 e500 Core PLL Ratio Table 47 describes the clock ratio between the e500 core complex bus (CCB) and the e500 core clock. This ratio is determined by the binary value of LALE and LGPL2 at power up, as shown in Table 47. Table 47. e500 Core to CCB Ratio Binary Value of LALE, LGPL2 Signals 00 01 10 11 Ratio Description 2:1 e500 core:CCB 5:2 e500 core:CCB 3:1 e500 core:CCB 7:2 e500 core:CCB 15.4 Frequency Options Table 48 shows the expected frequency values for the platform frequency when using a CCB to SYSCLK ratio in comparison to the memory bus speed. Table 48. Frequency Options with Respect to Memory Bus Speeds CCB to SYSCLK Ratio 17 25 33 42 SYSCLK (MHz) 67 83 100 111 133 Platform/CCB Frequency (MHz) 2 3 4 5 6 8 9 10 12 16 200 267 200 225 250 300 200 267 300 333 208 250 333 200 267 333 250 333 200 300 222 333 267 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 67 Thermal 16 Thermal This section describes the thermal specifications of the MPC8555E. 16.1 Thermal Characteristics Table 49. Package Thermal Characteristics Characteristic Symbol RJMA RJMA RJMA RJB RJC Value 17 14 13 10 0.96 Unit C/W C/W *C/W *C/W *C/W Notes 1, 2 1, 2 1, 2 3 4 Table 49 provides the package thermal characteristics for the MPC8555E. Junction-to-ambient Natural Convection on four layer board (2s2p) Junction-to-ambient (@200 ft/min or 1.0 m/s) on four layer board (2s2p) Junction-to-ambient (@400 ft/min or 2.0 m/s) on four layer board (2s2p) Junction-to-board thermal Junction-to-case thermal Notes 1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board) temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal resistance 2. Per JEDEC JESD51-6 with the board horizontal. 3. Thermal resistance between the die and the printed-circuit board per JEDEC JESD51-8. Board temperature is measured on the top surface of the board near the package. 4. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method 1012.1). Cold plate temperature is used for case temperature; measured value includes the thermal resistance of the interface layer. 16.2 Thermal Management Information This section provides thermal management information for the flip chip plastic ball grid array (FC-PBGA) package for air-cooled applications. Proper thermal control design is primarily dependent on the system-level design--the heat sink, airflow, and thermal interface material. The recommended attachment method to the heat sink is illustrated in Figure 42. The heat sink should be attached to the printed-circuit board with the spring force centered over the die. This spring force should not exceed 10 pounds force. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 68 Freescale Semiconductor Thermal FC-PBGA Package Heat Sink Heat Sink Clip Thermal Interface Material Lid Die Printed-Circuit Board Figure 42. Package Exploded Cross-Sectional View with Several Heat Sink Options The system board designer can choose between several types of heat sinks to place on the MPC8555E. There are several commercially-available heat sinks from the following vendors: Aavid Thermalloy 80 Commercial St. Concord, NH 03301 Internet: www.aavidthermalloy.com Alpha Novatech 473 Sapena Ct. #15 Santa Clara, CA 95054 Internet: www.alphanovatech.com International Electronic Research Corporation (IERC) 413 North Moss St. Burbank, CA 91502 Internet: www.ctscorp.com Millennium Electronics (MEI) Loroco Sites 671 East Brokaw Road San Jose, CA 95112 Internet: www.mei-millennium.com Tyco Electronics Chip CoolersTM P.O. Box 3668 Harrisburg, PA 17105-3668 Internet: www.chipcoolers.com Wakefield Engineering 33 Bridge St. Pelham, NH 03076 Internet: www.wakefield.com 603-224-9988 408-749-7601 818-842-7277 408-436-8770 800-522-6752 603-635-5102 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 69 Thermal Ultimately, the final selection of an appropriate heat sink depends on many factors, such as thermal performance at a given air velocity, spatial volume, mass, attachment method, assembly, and cost. Several heat sinks offered by Aavid Thermalloy, Alpha Novatech, IERC, Chip Coolers, Millennium Electronics, and Wakefield Engineering offer different heat sink-to-ambient thermal resistances, that will allow the MPC8555E to function in various environments. 16.2.1 Recommended Thermal Model For system thermal modeling, the MPC8555E thermal model is shown in Figure 52. Five cuboids are used to represent this device. To simplify the model, the solder balls and substrate are modeled as a single block 29x29x1.6 mm with the conductivity adjusted accordingly. The die is modeled as 8.7 x 9.3 mm at a thickness of 0.75 mm. The bump/underfill layer is modeled as a collapsed resistance between the die and substrate assuming a conductivity of 4.4 W/m*K in the thickness dimension of 0.07 mm. The lid attach adhesive is also modeled as a collapsed resistance with dimensions of 8.7 x 9.3 x 0.05 mm and the conductivity of 1.07 W/m*K. The nickel plated copper lid is modeled as 11 x 11 x 1 mm. Conductivity Value Unit Lid (11 x 11 x 1 mm) kx ky kz 360 360 360 z W/(m x K) Lid Die Substrate and solder balls Side View of Model (Not to Scale) Adhesive Bump/underfill Lid Adhesive--Collapsed resistance (8.7 x 9.3 x 0.05 mm) kz 1.07 Die (8.7 x 9.3 x 0.75 mm) Bump/Underfill--Collapsed resistance (8.7 x 9.3 x 0.07 mm) kz 4.4 x Substrate Substrate and Solder Balls (25 x 25 x 1.6 mm) kx ky kz 14.2 14.2 1.2 y Heat Source Top View of Model (Not to Scale) Figure 43. MPC8555E Thermal Model MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 70 Freescale Semiconductor Thermal 16.2.2 Internal Package Conduction Resistance For the packaging technology, shown in Table 49, the intrinsic internal conduction thermal resistance paths are as follows: * The die junction-to-case thermal resistance * The die junction-to-board thermal resistance Figure 44 depicts the primary heat transfer path for a package with an attached heat sink mounted to a printed-circuit board. External Resistance Radiation Convection Heat Sink Thermal Interface Material Internal Resistance Die/Package Die Junction Package/Leads Printed-Circuit Board External Resistance Radiation Convection (Note the internal versus external package resistance) Figure 44. Package with Heat Sink Mounted to a Printed-Circuit Board The heat sink removes most of the heat from the device. Heat generated on the active side of the chip is conducted through the silicon and through the lid, then through the heat sink attach material (or thermal interface material), and finally to the heat sink. The junction-to-case thermal resistance is low enough that the heat sink attach material and heat sink thermal resistance are the dominant terms. 16.2.3 Thermal Interface Materials A thermal interface material is required at the package-to-heat sink interface to minimize the thermal contact resistance. For those applications where the heat sink is attached by spring clip mechanism, Figure 45 shows the thermal performance of three thin-sheet thermal-interface materials (silicone, graphite/oil, floroether oil), a bare joint, and a joint with thermal grease as a function of contact pressure. As shown, the performance of these thermal interface materials improves with increasing contact pressure. The use of thermal grease significantly reduces the interface thermal resistance. The bare joint results in a thermal resistance approximately six times greater than the thermal grease joint. Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see Figure 41). Therefore, the synthetic grease offers the best thermal performance, especially at the low interface pressure. When removing the heat sink for re-work, it is preferable to slide the heat sink off slowly until the thermal interface material loses its grip. If the support fixture around the package prevents sliding off the heat sink, MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 71 Thermal the heat sink should be slowly removed. Heating the heat sink to 40-50*C with an air gun can soften the interface material and make the removal easier. The use of an adhesive for heat sink attach is not recommended. 2 Silicone Sheet (0.006 in.) Bare Joint Floroether Oil Sheet (0.007 in.) Graphite/Oil Sheet (0.005 in.) Synthetic Grease Specific Thermal Resistance (K-in.2/W) 1.5 1 0.5 0 0 10 20 30 40 50 60 70 80 Contact Pressure (psi) Figure 45. Thermal Performance of Select Thermal Interface Materials The system board designer can choose between several types of thermal interface. There are several commercially-available thermal interfaces provided by the following vendors: Chomerics, Inc. 77 Dragon Ct. Woburn, MA 01888-4014 Internet: www.chomerics.com Dow-Corning Corporation Dow-Corning Electronic Materials 2200 W. Salzburg Rd. Midland, MI 48686-0997 Internet: www.dowcorning.com Shin-Etsu MicroSi, Inc. 10028 S. 51st St. Phoenix, AZ 85044 Internet: www.microsi.com The Bergquist Company 18930 West 78th St. 781-935-4850 800-248-2481 888-642-7674 800-347-4572 MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 72 Freescale Semiconductor Thermal Chanhassen, MN 55317 Internet: www.bergquistcompany.com Thermagon Inc. 4707 Detroit Ave. Cleveland, OH 44102 Internet: www.thermagon.com 888-246-9050 16.2.4 Heat Sink Selection Examples The following section provides a heat sink selection example using one of the commercially available heat sinks. 16.2.4.1 Case 1 For preliminary heat sink sizing, the die-junction temperature can be expressed as follows: TJ = TI + TR + (JC + INT + SA) x PD where TJ is the die-junction temperature TI is the inlet cabinet ambient temperature TR is the air temperature rise within the computer cabinet JC is the junction-to-case thermal resistance INT is the adhesive or interface material thermal resistance SA is the heat sink base-to-ambient thermal resistance PD is the power dissipated by the device. See Table 4 and Table 5. During operation the die-junction temperatures (TJ) should be maintained within the range specified in Table 2. The temperature of air cooling the component greatly depends on the ambient inlet air temperature and the air temperature rise within the electronic cabinet. An electronic cabinet inlet-air temperature (TA) may range from 30 to 40C. The air temperature rise within a cabinet (TR) may be in the range of 5 to 10C. The thermal resistance of some thermal interface material (INT) may be about 1C/W. For the purposes of this example, the JC value given in Table 49 that includes the thermal grease interface and is documented in note 4 is used. If a thermal pad is used, INT must be added. Assuming a TI of 30 C, a TR of 5 C, a FC-PBGA package JC = 0.96, and a power consumption (PD) of 8.0 W, the following expression for TJ is obtained: Die-junction temperature: TJ = 30C + 5C + (0.96C/W + SA) x 8.0 W The heat sink-to-ambient thermal resistance (SA) versus airflow velocity for a Thermalloy heat sink #2328B is shown in Figure 46. Assuming an air velocity of 2 m/s, we have an effective SA+ of about 3.3 C/W, thus TJ = 30 C + 5 C + (0.96 C/W + 3.3 C/W) x 8.0 W, resulting in a die-junction temperature of approximately 69 C which is well within the maximum operating temperature of the component. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 73 Thermal 8 7 Heat Sink Thermal Resistance (C/W) Thermalloy #2328B Pin-fin Heat Sink (25 x 28 x 15 mm) 6 5 4 3 2 1 0 0.5 1 1.5 2 2.5 3 3.5 Approach Air Velocity (m/s) Figure 46. Thermalloy #2328B Heat Sink-to-Ambient Thermal Resistance Versus Airflow Velocity 16.2.4.2 Case 2 Every system application has different conditions that the thermal management solution must solve. As an alternate example, assume that the air reaching the component is 85 C with an approach velocity of 1 m/sec. For a maximum junction temperature of 105 C at 8 W, the total thermal resistance of junction to case thermal resistance plus thermal interface material plus heat sink thermal resistance must be less than 2.5 C/W. The value of the junction to case thermal resistance in Table 49 includes the thermal interface resistance of a thin layer of thermal grease as documented in footnote 4 of the table. Assuming that the heat sink is flat enough to allow a thin layer of grease or phase change material, then the heat sink must be less than 1.5 C/W. Millennium Electronics (MEI) has tooled a heat sink MTHERM-1051 for this requirement assuming a compactPCI environment at 1 m/sec and a heat sink height of 12 mm. The MEI solution is illustrated in Figure 47 and Figure 48. This design has several significant advantages: * The heat sink is clipped to a plastic frame attached to the application board with screws or plastic inserts at the corners away from the primary signal routing areas. * The heat sink clip is designed to apply the force holding the heat sink in place directly above the die at a maximum force of less than 10 lbs. * For applications with significant vibration requirements, silicone damping material can be applied between the heat sink and plastic frame. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 74 Freescale Semiconductor Thermal The spring mounting should be designed to apply the force only directly above the die. By localizing the force, rocking of the heat sink is minimized. One suggested mounting method attaches a plastic fence to the board to provide the structure on which the heat sink spring clips. The plastic fence also provides the opportunity to minimize the holes in the printed-circuit board and to locate them at the corners of the package. Figure 47 and provide exploded views of the plastic fence, heat sink, and spring clip. Figure 47. Exploded Views (1) of a Heat Sink Attachment using a Plastic Fence MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 75 Thermal Figure 48. Exploded Views (2) of a Heat Sink Attachment using a Plastic Force The die junction-to-ambient and the heat sink-to-ambient thermal resistances are common figure-of-merits used for comparing the thermal performance of various microelectronic packaging technologies, one should exercise caution when only using this metric in determining thermal management because no single parameter can adequately describe three-dimensional heat flow. The final die-junction operating temperature is not only a function of the component-level thermal resistance, but the system level design and its operating conditions. In addition to the component's power consumption, a number of factors affect the final operating die-junction temperature: airflow, board population (local heat flux of adjacent components), system air temperature rise, altitude, etc. Due to the complexity and the many variations of system-level boundary conditions for today's microelectronic equipment, the combined effects of the heat transfer mechanisms (radiation convection and conduction) may vary widely. For these reasons, we recommend using conjugate heat transfer models for the boards, as well as, system-level designs. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 76 Freescale Semiconductor System Design Information 17 System Design Information This section provides electrical and thermal design recommendations for successful application of the MPC8555E. 17.1 System Clocking The MPC8555E includes five PLLs. 1. The platform PLL (AVDD1) generates the platform clock from the externally supplied SYSCLK input. The frequency ratio between the platform and SYSCLK is selected using the platform PLL ratio configuration bits as described in Section 15.2, "Platform/System PLL Ratio." 2. The e500 Core PLL (AVDD2) generates the core clock as a slave to the platform clock. The frequency ratio between the e500 core clock and the platform clock is selected using the e500 PLL ratio configuration bits as described in Section 15.3, "e500 Core PLL Ratio." 3. The CPM PLL (AVDD3) is slaved to the platform clock and is used to generate clocks used internally by the CPM block. The ratio between the CPM PLL and the platform clock is fixed and not under user control. 4. The PCI1 PLL (AVDD4) generates the clocking for the first PCI bus. 5. The PCI2 PLL (AVDD5) generates the clock for the second PCI bus. 17.2 PLL Power Supply Filtering Each of the PLLs listed above is provided with power through independent power supply pins (AVDD1, AVDD2, AVDD3, AVDD4, and AVDD5 respectively). The AVDD level should always be equivalent to VDD, and preferably these voltages will be derived directly from VDD through a low frequency filter scheme such as the following. There are a number of ways to reliably provide power to the PLLs, but the recommended solution is to provide five independent filter circuits as illustrated in Figure 49, one to each of the five AVDD pins. By providing independent filters to each PLL the opportunity to cause noise injection from one PLL to the other is reduced. This circuit is intended to filter noise in the PLLs resonant frequency range from a 500 kHz to 10 MHz range. It should be built with surface mount capacitors with minimum Effective Series Inductance (ESL). Consistent with the recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic (Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value capacitor. Each circuit should be placed as close as possible to the specific AVDD pin being supplied to minimize noise coupled from nearby circuits. It should be possible to route directly from the capacitors to the AVDD pin, which is on the periphery of the 783 FC-PBGA footprint, without the inductance of vias. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 77 System Design Information Figure 49 shows the PLL power supply filter circuit. 10 VDD 2.2 F 2.2 F Low ESL Surface Mount Capacitors AVDD (or L2AVDD) GND Figure 49. PLL Power Supply Filter Circuit 17.3 Decoupling Recommendations Due to large address and data buses, and high operating frequencies, the MPC8555E can generate transient power surges and high frequency noise in its power supply, especially while driving large capacitive loads. This noise must be prevented from reaching other components in the MPC8555E system, and the MPC8555E itself requires a clean, tightly regulated source of power. Therefore, it is recommended that the system designer place at least one decoupling capacitor at each VDD, OVDD, GVDD, and LVDD pins of the MPC8555E. These decoupling capacitors should receive their power from separate VDD, OVDD, GVDD, LVDD, and GND power planes in the PCB, utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a standard escape pattern. Others may surround the part. These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology) capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes. In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB, feeding the VDD, OVDD, GVDD, and LVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should have a low ESR (equivalent series resistance) rating to ensure the quick response time necessary. They should also be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk capacitors--100-330 F (AVX TPS tantalum or Sanyo OSCON). 17.4 Connection Recommendations To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level. Unused active low inputs should be tied to OVDD, GVDD, or LVDD as required. Unused active high inputs should be connected to GND. All NC (no-connect) signals must remain unconnected. Power and ground connections must be made to all external VDD, GVDD, LVDD, OVDD, and GND pins of the MPC8555E. 17.5 Output Buffer DC Impedance The MPC8555E drivers are characterized over process, voltage, and temperature. For all buses, the driver is a push-pull single-ended driver type (open drain for I2C). To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 50). The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 78 Freescale Semiconductor System Design Information When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2. OVDD RN SW2 Data Pad SW1 RP OGND Figure 50. Driver Impedance Measurement The value of this resistance and the strength of the driver's current source can be found by making two measurements. First, the output voltage is measured while driving logic 1 without an external differential termination resistor. The measured voltage is V1 = Rsource x Isource. Second, the output voltage is measured while driving logic 1 with an external precision differential termination resistor of value Rterm. The measured voltage is V2 = 1/(1/R1 + 1/R2)) x Isource. Solving for the output impedance gives Rsource = Rterm x (V1/V2 - 1). The drive current is then Isource = V1/Rsource. Table 50 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD, nominal OVDD, 105C. Table 50. Impedance Characteristics Local Bus, Ethernet, DUART, Control, Configuration, Power Management 43 Target 43 Target NA Impedance PCI DDR DRAM Symbol Unit RN RP Differential 25 Target 25 Target NA 20 Target 20 Target NA Z0 Z0 ZDIFF Note: Nominal supply voltages. See Table 1, Tj = 105C. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 79 System Design Information 17.6 Configuration Pin Multiplexing The MPC8555E provides the user with power-on configuration options which can be set through the use of external pull-up or pull-down resistors of 4.7 k on certain output pins (see customer visible configuration pins). These pins are generally used as output only pins in normal operation. While HRESET is asserted however, these pins are treated as inputs. The value presented on these pins while HRESET is asserted, is latched when HRESET deasserts, at which time the input receiver is disabled and the I/O circuit takes on its normal function. Most of these sampled configuration pins are equipped with an on-chip gated resistor of approximately 20 k. This value should permit the 4.7-k resistor to pull the configuration pin to a valid logic low level. The pull-up resistor is enabled only during HRESET (and for platform/system clocks after HRESET deassertion to ensure capture of the reset value). When the input receiver is disabled the pull-up is also, thus allowing functional operation of the pin as an output with minimal signal quality or delay disruption. The default value for all configuration bits treated this way has been encoded such that a high voltage level puts the device into the default state and external resistors are needed only when non-default settings are required by the user. Careful board layout with stubless connections to these pull-down resistors coupled with the large value of the pull-down resistor should minimize the disruption of signal quality or speed for output pins thus configured. The platform PLL ratio and e500 PLL ratio configuration pins are not equipped with these default pull-up devices. 17.7 Pull-Up Resistor Requirements The MPC8555E requires high resistance pull-up resistors (10 k is recommended) on open drain type pins. Correct operation of the JTAG interface requires configuration of a group of system control pins as demonstrated in Figure 52. Care must be taken to ensure that these pins are maintained at a valid deasserted state under normal operating conditions as most have asynchronous behavior and spurious assertion will give unpredictable results. TSEC1_TXD[3:0] must not be pulled low during reset. Some PHY chips have internal pulldowns that could cause this to happen. If such PHY chips are used, then a pullup must be placed on these signals strong enough to restore these signals to a logical 1 during reset. Refer to the PCI 2.2 specification for all pull-ups required for PCI. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 80 Freescale Semiconductor System Design Information 17.8 JTAG Configuration Signals Boundary-scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the IEEE Std 1149.1 specification, but is provided on all processors that implement the Power Architecture. The device requires TRST to be asserted during reset conditions to ensure the JTAG boundary logic does not interfere with normal chip operation. While it is possible to force the TAP controller to the reset state using only the TCK and TMS signals, generally systems will assert TRST during the power-on reset flow. Simply tying TRST to HRESET is not practical because the JTAG interface is also used for accessing the common on-chip processor (COP) function. The COP function of these processors allow a remote computer system (typically, a PC with dedicated hardware and debugging software) to access and control the internal operations of the processor. The COP interface connects primarily through the JTAG port of the processor, with some additional status monitoring signals. The COP port requires the ability to independently assert HRESET or TRST in order to fully control the processor. If the target system has independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or push-button switches, then the COP reset signals must be merged into these signals with logic. The arrangement shown in Figure 51 allows the COP port to independently assert HRESET or TRST, while ensuring that the target can drive HRESET as well. The COP interface has a standard header, shown in Figure 51, for connection to the target system, and is based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg header). The connector typically has pin 14 removed as a connector key. The COP header adds many benefits such as breakpoints, watchpoints, register and memory examination/modification, and other standard debugger features. An inexpensive option can be to leave the COP header unpopulated until needed. There is no standardized way to number the COP header; consequently, many different pin numbers have been observed from emulator vendors. Some are numbered top-to-bottom then left-to-right, while others use left-to-right then top-to-bottom, while still others number the pins counter clockwise from pin 1 (as with an IC). Regardless of the numbering, the signal placement recommended in Figure 51 is common to all known emulators. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 81 System Design Information COP_TDO COP_TDI NC COP_TCK COP_TMS COP_SRESET COP_HRESET COP_CHKSTP_OUT 1 3 5 7 9 11 13 15 2 4 6 8 10 12 KEY No pin 16 NC COP_TRST COP_VDD_SENSE COP_CHKSTP_IN NC NC GND Figure 51. COP Connector Physical Pinout 17.8.1 Termination of Unused Signals If the JTAG interface and COP header will not be used, Freescale recommends the following connections: * TRST should be tied to HRESET through a 0 k isolation resistor so that it is asserted when the system reset signal (HRESET) is asserted, ensuring that the JTAG scan chain is initialized during the power-on reset flow. Freescale recommends that the COP header be designed into the system as shown in Figure 52. If this is not possible, the isolation resistor will allow future access to TRST in case a JTAG interface may need to be wired onto the system in future debug situations. * Tie TCK to OVDD through a 10 k resistor. This will prevent TCK from changing state and reading incorrect data into the device. * No connection is required for TDI, TMS, or TDO. MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 82 Freescale Semiconductor System Design Information OVDD SRESET HRESET 10 k SRESET 6 HRESET1 From Target Board Sources (if any) 10 k 13 11 COP_HRESET COP_SRESET 10 k 10 k 5 10 k 10 k TRST1 1 3 5 7 9 11 2 4 6 8 10 12 4 6 5 COP Header 15 14 3 COP_TRST COP_VDD_SENSE2 NC COP_CHKSTP_OUT 10 k 10 k COP_CHKSTP_IN 10 CKSTP_OUT KEY 13 No pin 8 COP_TMS 9 COP_TDO COP_TDI COP_TCK 7 2 10 12 16 NC NC 4 CKSTP_IN TMS TDO TDI TCK 10 k 15 16 COP Connector Physical Pinout 1 3 Notes: 1. The COP port and target board should be able to independently assert HRESET and TRST to the processor in order to fully control the processor as shown here. 2. Populate this with a 10 resistor for short-circuit/current-limiting protection. 3. The KEY location (pin 14) is not physically present on the COP header. 4. Although pin 12 is defined as a No-Connect, some debug tools may use pin 12 as an additional GND pin for improved signal integrity. 5. This switch is included as a precaution for BSDL testing. The switch should be open during BSDL testing to avoid accidentally asserting the TRST line. If BSDL testing is not being performed, this switch should be closed or removed. 6. Asserting SRESET causes a machine check interrupt to the e500 core. Figure 52. JTAG Interface Connection MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 83 Document Revision History 18 Document Revision History Table 58 provides a revision history for this hardware specification. Table 51. Document Revision History Rev. No. 4 Date 12/2006 Substantive Change(s) Updated Section 2.1.2, "Power Sequencing." Updated back page information. Updated Section 2.1.2, "Power Sequencing." Replaced Section 17.8, "JTAG Configuration Signals." Table 4: Added footnote 2 about junction temperature. Table 4: Added max. power values for 1000 MHz core frequency. Removed Figure 3, "Maximum AC Waveforms on PCI Interface for 3.3-V Signaling." Table 30: Modified note to tLBKSKEW from 8 to 9 Table 30: Changed tLBKHOZ1 and tLBKHOV2 values. Table 30: Added note 3 to tLBKHOV1. Table 30 and Table 31: Modified note 3. Table 31: Added note 3 to tLBKLOV1. Table 31: Modified values for tLBKHKT, tLBKLOV1, tLBKLOV2, tLBKLOV3, tLBKLOZ1, and tLBKLOZ2. Figure 20: Changed Input Signals: LAD[0:31]/LDP[0:3]. Table 43: Modified note for signal CLK_OUT. Table 43: PCI1_CLK and PCI2_CLK changed from I/O to I. Table 52: Added column for Encryption Acceleration. Table 4: Modified max. power values. Table 43: Modified notes for signals TSEC1_TXD[3:0], TSEC2_TXD[3:0], TRIG_OUT/READY, MSRCID4, CLK_OUT, and MDVAL. Previous revision's history listed incorrect cross references. Table 2 is now correctly listed as Table 27 and Table 38 is now listed as Table 31. Table 7: Added note 2. Table 14: Modified min and max values for tDDKHMP Table 27: Changed LVdd to OVdd for the supply voltage Ethernet management interface. Table 4: Modified footnote 4 and changed typical power for the 1000MHz core frequency. Table 31: Corrected symbols for body rows 9-15, effectively changing them from a high state to a low state. Initial Release. 3.2 11/2006 3.1 10/2005 3 8/29/2005 2 8/2005 1 6/2005 0 6/2005 19 Device Nomenclature Ordering information for the parts fully covered by this specification document is provided in Section 19.1, "Nomenclature of Parts Fully Addressed by this Document." 19.1 Nomenclature of Parts Fully Addressed by this Document Table 52 provides the Freescale part numbering nomenclature for the MPC8555E. Note that the individual part numbers correspond to a maximum processor core frequency. For available frequencies, contact your MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 84 Freescale Semiconductor Device Nomenclature local Freescale sales office. In addition to the processor frequency, the part numbering scheme also includes an application modifier which may specify special application conditions. Each part number also contains a revision code which refers to the die mask revision number. Table 52. Part Numbering Nomenclature MPC nnnn Product Part Encryption Code Identifier Acceleration MPC 8555 Blank = not included E = included t Temperature Range1 pp Package 2 aa Processor Frequency 3 AJ = 533 MHz AK = 600 MHz AL = 667 MHz AP = 833 MHz AQ = 1000 MHZ a Platform Frequency D = 266 MHz E = 300 MHz F = 333 MHz r Revision Level4 Blank = 0 to 105C PX = FC-PBGA C = -40 to 105C VT = FC-PBGA (lead free) Notes: 1. For Temperature Range=C, Processor Frequency is limited to 667 MHz with a Platform Frequency selector of 333 MHz, Processor Frequency is limited to 533 MHz with a Platform Frequency selector of 266 MHz. 2. See Section 14, "Package and Pin Listings," for more information on available package types. 3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other maximum core frequencies. 4. Contact you local Freescale field applications engineer (FAE). 19.2 Part Marking Parts are marked as the example shown in Figure 53. MPCnnnn MPC85nn xPXxxxn tppaaar MMMMM ATWLYYWWA CCCCC Notes: MMMMM is the 5-digit mask number. ATWLYYWWA is the traceability code. CCCCC is the country of assembly. This space is left blank if parts are assembled in the United States. 85xx FC-PBGA Figure 53. Part Marking for FC-PBGA Device MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 85 Device Nomenclature THIS PAGE INTENTIONALLY LEFT BLANK MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 86 Freescale Semiconductor Device Nomenclature THIS PAGE INTENTIONALLY LEFT BLANK MPC8555E PowerQUICCTM III Integrated Communications Processor Hardware Specifications, Rev. 4 Freescale Semiconductor 87 How to Reach Us: Home Page: www.freescale.com Web Support: http://www.freescale.com/support USA/Europe or Locations Not Listed: Freescale Semiconductor, Inc. Technical Information Center, EL516 2100 East Elliot Road Tempe, Arizona 85284 +1-800-521-6274 or +1-480-768-2130 www.freescale.com/support Europe, Middle East, and Africa: Freescale Halbleiter Deutschland GmbH Technical Information Center Schatzbogen 7 81829 Muenchen, Germany +44 1296 380 456 (English) +46 8 52200080 (English) +49 89 92103 559 (German) +33 1 69 35 48 48 (French) www.freescale.com/support Japan: Freescale Semiconductor Japan Ltd. Headquarters ARCO Tower 15F 1-8-1, Shimo-Meguro, Meguro-ku Tokyo 153-0064 Japan 0120 191014 or +81 3 5437 9125 support.japan@freescale.com Asia/Pacific: Freescale Semiconductor Hong Kong Ltd. Technical Information Center 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong +800 2666 8080 support.asia@freescale.com For Literature Requests Only: Freescale Semiconductor Literature Distribution Center P.O. Box 5405 Denver, Colorado 80217 +1-800 441-2447 or +1-303-675-2140 Fax: +1-303-675-2150 LDCForFreescaleSemiconductor @hibbertgroup.com Information in this document is provided solely to enable system and software implementers to use Freescale Semiconductor products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Freescale Semiconductor reserves the right to make changes without further notice to any products herein. Freescale Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Freescale Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Freescale Semiconductor does not convey any license under its patent rights nor the rights of others. Freescale Semiconductor products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Freescale Semiconductor product could create a situation where personal injury or death may occur. Should Buyer purchase or use Freescale Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Freescale Semiconductor was negligent regarding the design or manufacture of the part. FreescaleTM and the Freescale logo are trademarks of Freescale Semiconductor, Inc. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. The described product contains a PowerPC processor core. The PowerPC name is a trademark of IBM Corp. and used under license. All other product or service names are the property of their respective owners. (c) Freescale Semiconductor, Inc., 2004, 2006. All rights reserved. Document Number: MPC8555EEC Rev. 4 12/2006 |
Price & Availability of MPC8555E |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |