 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MIG150J7CSB1W TOSHIBA Intelligent Power Module Silicon N Channel IGBT MIG150J7CSB1W (600V/150A 7in1) High Power Switching Applications Motor Control Applications * * * * * * Integrates inverter, brake power circuit and control circuits (IGBT drive units, and units for protection against short-circuit current, over-current, under-voltage and over-temperature) into a single package. The electrodes are isolated from the case Low thermal resistance VCE (sat) = 1.9 V (typ.) UL recognized: File No.E87989 Weight: 278 g (typ.) Equivalent Circuit 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 FO IN VD GND FO IN VD GND FO IN VD GND FO IN VD GND GND IN FO VD GND IN FO VD GND IN FO VD GND VS OUT GND VS OUT GND VS OUT GND VS OUT GND VS OUT GND VS OUT GND VS OUT W 1. 8. 15. VD (U) GND (V) Open 2. 9. 16. V FO (U) VD (W) IN (B) 3. 10. 17. IN (U) FO (W) IN (X) U 4. 11. 18. GND (U) IN (W) IN (Y) B 5. 12. 19. VD (V) GND (W) IN (Z) 6. 13. 20. FO (V) VD (L) GND (L) N 7. 14. IN (V) FO (L) P 1 2001-11-13 MIG150J7CSB1W Package Dimensions: TOSHIBA 2-108G1A Unit: mm 1. 7. 13. 19. VD (U) IN (V) VD (L) IN (Z) 2. 8. 14. 20. FO (U) GND (V) FO (L) GND (L) 3. 9. 15. IN (U) VD (W) Open 4. 10. 16. GND (U) FO (W) IN (B) 5. 11. 17. VD (V) IN (W) IN (X) 6. 12. 18. FO (V) GND (W) IN (Y) 2 2001-11-13 MIG150J7CSB1W Signal Terminal Layout Unit: mm 1. 7. 13. 19. VD (U) IN (V) VD (L) IN (Z) 2. 8. 14. 20. FO (U) GND (V) FO (L) GND (L) 3. 9. 15. IN (U) VD (W) Open 4. 10. 16. GND (U) FO (W) IN (B) 5. 11. 17. VD (V) IN (W) IN (X) 6. 12. 18. FO (V) GND (W) IN (Y) 3 2001-11-13 MIG150J7CSB1W Maximum Ratings (Tj = 25C) Stage Supply voltage Collector-emitter voltage Inverter Collector current Forward current Collector power dissipation Junction temperature Supply voltage Collector-emitter voltage Collector current Brake Reverse voltage Forward current Collector power dissipation Junction temperature Control supply voltage Control Input voltage Fault output voltage Fault output current Operating temperature Storage temperature Range Module Isolation voltage Screw torque (Terminal) Screw torque (Mounting) AC 1 min M4 M5 Tc = 25C, DC Tc = 25C 3/4 VD-GND Terminal IN-GND Terminal FO-GND Terminal FO sink current Tc = 25C, DC 3/4 Tc = 25C, DC Tc = 25C, DC Tc = 25C, DC 3/4 P-N Power terminal 3/4 Characteristic Condition P-N Power terminal 3/4 Symbol VCC VCES IC IF PC Tj VCC VCES IC VR IF PC Tj VD VIN VFO IFO Tc Tstg VISO 3/4 3/4 Rating 450 600 150 150 740 150 450 600 75 600 75 460 150 20 20 20 14 -20~ + 100 -40~ + 125 2500 2 3 Unit V V A A W C V V A V A W C V V V mA C C V Nm 3/4 3/4 Electrical Characteristics 1. Inverter stage Characteristics Collector cut-off current Symbol ICEX Test Condition VCE = 600 V VD = 15 V IC = 150 A VIN = 15 V (R) 0 V Tj = 25C Tj = 125C Tj = 25C Tj = 125C Min 3/4 3/4 1.6 3/4 3/4 3/4 VCC = 300 V, IC = 150 A VD = 15 V, VIN = 15 V 0 V Tj = 25C, Inductive load (Note 1) 3/4 3/4 3/4 3/4 Typ. 3/4 3/4 1.9 2.1 2.4 1.3 0.3 0.3 1.1 0.2 Max 1 10 2.3 3/4 2.8 2.2 3/4 3/4 2.1 3/4 ms V V Unit mA Collector-emitter saturation voltage Forward voltage VCE (sat) VF ton tc (on) IF = 150 A, Tj = 25C Switching time trr toff tc (off) Note 1: Switching time test circuit & timing chart 4 2001-11-13 MIG150J7CSB1W 2. Brake stage Characteristics Collector cut-off current Symbol ICEX Test Condition VCE = 600 V VD = 15 V IC = 75 A VIN = 15 V (R) 0 V VR = 600 V IF = 75 A, Tj = 25C VCC = 300 V, IC = 75 A VD = 15 V, VIN = 15 V 0 V Tj = 25C, Inductive load (Note 1) Tj = 25C Tj = 125C Tj = 25C Tj = 125C Tj = 25C Tj = 125C Min 3/4 3/4 3/4 3/4 3/4 3/4 1.7 3/4 3/4 3/4 3/4 3/4 Typ. 3/4 3/4 1.8 2.0 3/4 3/4 2.2 1.6 0.65 0.45 1.4 0.2 Max 1 10 2.2 3/4 1 mA 10 2.6 2.2 3/4 3/4 2.4 3/4 ms V V Unit mA Collector-emitter saturation voltage VCE (sat) Reverse current Forward voltage IR VF ton tc (on) Switching time trr toff tc (off) Note 1: Switching time test circuit & timing chart 3. Control stage (Tj = 25C) Characteristics Control circuit current Input on signal voltage Input off signal voltage Protection Fault output current Normal Over current protection trip level Inverter OC Brake SC toff (OC) Trip level Reset level Trip level Reset level OT Case temperature OTr UV UVr tFO VD = 15 V 3/4 High side Low side Symbol ID (H) ID (L) VIN (on) VIN (off) IFO (on) IFO (off) VD = 15 V Test Condition Min 3/4 3/4 1.4 2.2 3/4 3/4 240 120 240 120 3/4 110 3/4 11.0 12.0 1 Typ. 13 52 1.6 2.5 10 3/4 3/4 3/4 3/4 3/4 5 118 98 12.0 12.5 2 Max 17 68 1.8 V 2.8 12 mA 0.1 3/4 3/4 3/4 3/4 3/4 125 3/4 12.5 V 13.0 3 ms C A Unit mA VD = 15 V VD = 15 V VD = 15 V, Tj < 125C = VD = 15 V, Tj < 125C = VD = 15 V Short circuit protection trip Inverter level Brake Over current cut-off time Over temperature protection Control supply under voltage protection Fault output pulse width A ms 4. Thermal resistance (Tc = 25C) Characteristics Symbol Test Condition Inverter IGBT Junction to case thermal resistance Rth (j-c) Inverter FRD Brake IGBT Brake FRD Case to fin thermal resistance Rth (c-f) Compound is applied Min 3/4 3/4 3/4 3/4 3/4 Typ. 3/4 3/4 3/4 3/4 0.017 Max 0.167 0.313 0.270 0.600 3/4 C/W C/W Unit 5 2001-11-13 MIG150J7CSB1W Switching Time Test Circuit Intelligent power module TLP559 VD 0.1 mF 15 kW OUT IN 15 V 22 mF GND VS P GND U (V, W, B) VCC VD IF = 16mA PG 15 V 22 mF GND 0.1 mF 15 kW OUT IN VS N GND Timing Chart Input pulse 15 V VIN Waveform 0 2.5 V 1.6 V 90% Irr IC Waveform Irr 90% trr 20% Irr VCE Waveform 10% toff 10% tc (off) 10% ton 10% tc (on) 6 2001-11-13 MIG150J7CSB1W 5. Recommended conditions for application Characteristics Supply voltage Control supply voltage Carrier frequency Dead time Symbol VCC VD fc tdead Test Condition P-N Power terminal VD-GND Signal terminal PWM Control Switching time test circuit (See page.6) (Note 2) Min 3/4 13.5 3/4 3 Typ. 300 15 3/4 3/4 Max 400 16.5 20 3/4 Unit V V kHz ms Note 2: The table lists Dead time requirements for the module input, excluding photocoupler delays. When specifying dead time requirements for the photocoupler input, please add photocoupler delays to the dead time given above. Dead Time Timing Chart 15 V VIN Waveform 0 15 V VIN Waveform 0 tdead tdead 7 2001-11-13 MIG150J7CSB1W IC - VCE 300 VD = 17 V 250 13 V 250 15 V 200 300 IC - VCE VD = 17 V 13 V (A) (A) IC Collector current Collector current IC 200 15 V 150 150 100 100 50 Common emitter Tj = 25C 0 0 1 2 3 4 50 Common emitter Tj = 125C 0 0 1 2 3 4 Collector-emitter voltage VCE (V) Collector-emitter voltage VCE (V) Switching time - IC 10 5 3 10 5 3 Switching time - IC (ms) 1 0.5 0.3 (ms) ton toff ton toff 1 0.5 0.3 tc (on) tc (off) Switching time tc (on) tc (off) 0.1 0.05 0.03 Tj = 25C VCC = 300 V VD = 15 V L-Load 50 100 150 200 Switching time 0.1 0.05 0.03 Tj = 125C VCC = 300 V VD = 15 V L-Load 50 100 150 200 0.01 0 0.01 0 Collector current IC (A) Collector current IC (A) IF - VF 300 100 trr, Irr - IF Peak reverse recovery current Irr (A) Peak reverse recovery time trr (10ns) Irr 250 (A) 30 trr Forward current IF 200 150 10 100 Common cathode 50 :Tj = 25C :Tj = 125C 3 Common cathode :Tj = 25C :Tj = 125C 0 0 1 2 3 4 1 0 50 100 150 200 Forward voltage VF (V) Forward current IF (A) 8 2001-11-13 MIG150J7CSB1W OC - TC (mA) 400 30 ID (H) - fc Over current protection trip level OC (A) Inverter stage 300 High side control circuit current ID (H) 25 20 200 Brake stage 15 10 100 5 VD = 15 V Tj = 25C 0 0 5 10 15 20 25 VD = 15 V 0 0 25 50 75 100 125 150 Case temperature TC (C) Carrier frequency fc (kHz) ID (L) - fc (mA) 120 280 Reverse bias SOA OC Low side control circuit current ID (L) 100 240 (A) IC Collector current VD = 15 V Tj = 25C 0 0 5 10 15 20 25 80 60 40 20 200 160 120 80 40 0 0 Tj < 125C = VD = 15 V 100 200 300 400 500 600 700 Carrier frequency fc (kHz) Collector-emitter voltage VCE (V) Rth (t) - tw Inverter stage (C/W) Tc = 25C Diode stage Rth (t) - tw Brake stage (C/W) 1 0.5 0.3 Tc = 25C Diode stage Transistor stage 0.1 0.05 0.03 1 0.5 0.3 Transient thermal resistance Rth (t) 0.1 0.05 0.03 Transistor stage 0.01 0.005 0.003 Transient thermal resistance Rth (t) 10 0.01 0.005 0.003 0.001 0.001 0.01 0.1 1 0.001 0.001 0.01 0.1 1 10 Pulse width tw (s) Pulse width tw (s) 9 2001-11-13 MIG150J7CSB1W Turn on loss - IC 100 100 Turn off loss - IC (mJ) 10 (mJ) Eoff 10 Turn on loss Eon 0.1 Turn off loss 1 1 0.01 0 VCC = 300 V VD = 15 V L-LOAD : Tj = 25C : Tj = 125C 50 100 150 200 0.1 0.01 0 VCC = 300 V VD = 15 V L-LOAD : Tj = 25C : Tj = 125C 50 100 150 200 Collector current IC (A) Collector current IC (A) 10 2001-11-13 MIG150J7CSB1W RESTRICTIONS ON PRODUCT USE 000707EAA * TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the "Handling Guide for Semiconductor Devices," or "TOSHIBA Semiconductor Reliability Handbook" etc.. * The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury ("Unintended Usage"). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer's own risk. * The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. * The information contained herein is subject to change without notice. 11 2001-11-13 |
Price & Availability of MIG150J7CSB1W
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |