 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| PM10RSH120 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts X S Q T 1234 A B C D P P 5678 9 11 P 13 15 17 19 F Y (15 TYP.) 10 12 14 16 18 H U (4 TYP.) P B N U V W G V - DIA. (4 TYP.) N M M M E M M Z 1. V UPC 2. UFO 3. U P 4. V UPI 5. VVPC 6. VFO 7. V P 8. V VPI 9. V WPC 10. WFO 11. WP 12. V WPI 13. V NC 14. V NI 15. B R 16. U N 17. V N 18. WN 19. FO 20. P 21. B 22. N 23. U 24. V 25. W 2.0 0.1 X 0.5 0.1 MM PIN (6 TYP.) 0.6 0.1 X 0.4 0.1 MM PIN (19 TYP.) W L R J K X V WPC V UPC V VPC VP V FO WP W FO V WPI V UPI V VPI UP U FO V NC WN Description: Powerex IntellimodTM Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: Complete Output Power Circuit Gate Drive Circuit Protection Logic - Short Circuit - Over Current - Over Temperature - Under Voltage Applications: Inverters UPS Motion/Servo Control Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM10RSH120 is a 1200V, 10 Ampere IntellimodTM Intelligent Power Module. Type PM Current Rating Amperes 10 VCES Volts (x 10) 120 V NI OUT V CC OUT V CC OUT V CC UN OUT V CC FO BR VN OUT V CC OUT V CC TEMP B N W V U OUT V CC GND GND GND GND GND GND GND GND GND GND GND GND GND GND FO FO FO FO FO FO SI SI SI SI SI SI SI FO IN IN IN IN IN IN IN P Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L M Inches 3.980.04 3.70 3.480.03 2.7000.03 2.660.02 2.360.04 1.850.02 1.830.03 1.46 1.14 0.710.04 0.530.01 Millimeters 101.01.0 94.0 88.50.8 68.580.8 67.50.5 60.01.0 47.00.5 46.50.8 37.0 29.0 18.01.0 13.50.3 Dimensions N P Q R S T U V W X Y Z Inches 0.41 0.400 0.392 0.31 0.26 0.246 0.18 Rad. 0.18 Dia. 0.160.02 0.14 0.1000.01 0.02 Millimeters 10.5 10.16 9.96 8.0 6.5 6.25 Rad. 4.5 Dia. 4.5 4.00.5 3.5 2.540.25 0.5 577 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25C unless otherwise specified Characteristics Power Device Junction Temperature Storage Temperature Case Operating Temperature Mounting Torque, M4 Mounting Screws Module Weight (Typical) Supply Voltage Protected by OC and SC (VD = 13.5 - 16.5V, Inverter Part, Tj = 125C) Isolation Voltage, AC 1 minute, 60Hz Sinusoidal Symbol Tj Tstg TC -- -- VCC(prot.) VRMS PM10RSH120 -20 to 150 -40 to 125 -20 to 100 13 100 800 2500 Units C C C in-lb Grams Volts Volts Control Sector Supply Voltage Applied between (VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC) Input Voltage Applied between (UP, VP, WP, UN, VN, WN, Br) Fault Output Supply Voltage Fault Output Current VD VCIN VFO IFO 20 20 20 20 Volts Volts Volts mA IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) Collector Current, Peak Collector Current, Supply Voltage (Applied between P - N) Supply Voltage, Surge (Applied between P - N) Collector Dissipation VCES IC ICP VCC VCC(surge) PC 1200 10 20 900 1000 62 Volts Amperes Amperes Volts Volts Watts Brake Sector Collector-Emitter Voltage Collector Current, Peak Collector Current, Supply Voltage (Applied between P - N) Supply Voltage, Surge (Applied between P - N) Collector Dissipation Diode Forward Current Diode DC Reverse Voltage VCES IC ICP VCC VCC(surge) PC IF VR(DC) 1200 10 20 900 1000 41 10 1200 Volts Amperes Amperes Volts Volts Watts Amperes Volts 578 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Control Sector Over Current Trip Level Inverter Part Over Current Trip Level Brake Part Short Circuit Trip Level Inverter Part Short Circuit Trip Level Brake Part Over Current Delay Time Over Temperature Protection toff(OC) OT OTR Supply Circuit Under Voltage Protection UV UVR Supply Voltage VD ID VCIN(on) VCIN(off) fPWM IFO(H) IFO(L) Minimum Fault Output Pulse Width tFO VD = 15V Trip Level Reset Level Trip Level Reset Level Applied between VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC Circuit Current VD = 15V, VCIN = 15V, VN1-VNC VD = 15V, VCIN = 15V, VXP1-VXPC Input ON Threshold Voltage Input OFF Threshold Voltage PWM Input Frequency Fault Output Current Applied between UP, VP, WP, UN, VN, WN, Br 3Sinusoidal VD = 15V, VFO = 15V VD = 15V, VFO = 15V VD = 15V -- -- 1.2 1.7 -- -- -- 1.0 25 7 1.5 2.0 15 -- 10 1.8 35 10 1.8 2.3 20 0.01 15 -- mA mA Volts Volts kHz mA mA mS SC -20C T 125C OC -20C T 125C 15 15 -- -- -- 100 -- 11.5 -- 13.5 27 27 41 41 10 110 90 12.0 12.5 15 -- -- -- -- -- 120 -- 12.5 -- 16.5 Amperes Amperes Amperes Amperes S C C Volts Volts Volts 579 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Electrical and Mechanical Characteristics, Tj = 25C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units IGBT Inverter Sector Collector Cutoff Current ICES VFM VCE(sat) VCE = VCES, Tj = 25C VCE = VCES, Tj = 125C Diode Forward Voltage Collector-Emitter Saturation Voltage -IC = 10A, VD = 15V, VCIN = 5V VD = 15V, VCIN = 0V, IC = 10A VD = 15V, VCIN = 0V, IC = 10A, Tj = 125C Inductive Load Switching Times ton trr tC(on) toff tC(off) VD = 15V, VCIN = 0V ~ 15V VCC = 600V, IC = 10A Tj = 125C 0.4 -- -- -- -- 0.7 0.15 0.3 1.7 0.6 1.5 0.3 1.0 2.9 1.2 S S S S S -- -- -- -- -- -- -- 2.5 2.3 2.1 1.0 10 3.5 3.3 3.1 mA mA Volts Volts Volts Brake Sector Collector-Emitter Saturation Voltage VCE(sat) Tj = 25C VD = 15V, VCIN = 0V, IC = 10A, Tj = 125C Diode Forward Voltage Collector Cutoff Current VFM ICES -IC = 10A, VD = 15V, VCIN = 5V VCE = VCES, Tj = 25C VCE = VCES, Tj = 125C -- -- -- 2.5 -- -- 3.5 1 10 Volts mA mA -- 2.5 3.5 Volts VD = 15V, VCIN = 0V, IC = 10A, -- 2.8 3.8 Volts 580 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Thermal Characteristics Characteristic Junction to Case Thermal Resistance Symbol Rth(j-c)Q Rth(j-c)D Rth(c-f)Q Rth(c-f)D Contact Thermal Resistance Rth(c-f) Condition Each Inverter IGBT Each Inverter FWDi Each Brake IGBT Each Brake FWDi Case to Fin Per Module, Thermal Grease Applied Min. -- -- -- -- -- Typ. -- -- -- -- -- Max. 2.0 5.5 3.0 5.5 Units C/Watt C/Watt C/Watt C/Watt 0.044 C/Watt Recommended Conditions for Use Characteristic Supply Voltage Symbol VCC VD Input ON Voltage Input OFF Voltage PWM Input Frequency Minimum Dead Time VCIN(on) VCIN(off) fPWM tDEAD Condition Applied across P-N Terminals Applied between VUP1-VUPC, VN1-VNC, VVP1-VVPC, VWP1-VWPC Applied between UP, VP, WP, UN, VN, WN, Br Using Application Circuit Input Signal 0 ~ 0.8 4.0 ~ VD 5 ~ 20 2.5 Volts Volts kHz S Value 0 ~ 800 15 1.5 Units Volts Volts 581 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Inverter Part SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 3.0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) SATURATION VOLTAGE VCE(sat), (VOLTS) 3.0 2.5 2.0 1.5 1.0 0.5 0 0 5 10 15 20 0 12 14 16 18 20 COLLECTOR CURRENT, IC, (AMPERES) SUPPLY VOLTAGE, VD, (VOLTS) COLLECTOR CURRENT, IC, (AMPERES) 15.0 Tj = 25oC VCIN = 0V 15 VD = 17V 13 2.5 2.0 1.5 1.0 0.5 0 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC 10.0 IC = 50A VCIN = 0V Tj = 25oC Tj = 125oC 5.0 0 0 1.0 2.0 3.0 4.0 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) SWITCHING TIME VS. COLLECTOR CURRENT (TYPICAL) REVERSE RECOVERY CURRENT VS. COLLECTOR CURRENT (TYPICAL) 101 VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 100 REVERSE RECOVERY TIME, trr, ( S) 103 VCC = 600V VD = 15V Tj = 25oC Tj = 125oC VCC = 600V VD = 15V Tj = 25oC Tj = 125oC 102 REVERSE RECOVERY CURRENT, Irr, (AMPERES) 100 toff ton SWITCHING TIMES, tc(on), tc(off), (s) SWITCHING TIMES, ton, toff, (s) 10-1 tc(off) tc(on) 102 trr 101 Irr 10-1 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 10-2 100 101 COLLECTOR CURRENT, IC, (AMPERES) 102 101 100 101 EMITTER CURRENT, IC, (AMPERES) 100 102 DIODE FORWARD CHARACTERISTICS OVER CURRENT TRIP LEVEL VS. SUPPLY VOLTAGE (TYPICAL) OVER CURRENT TRIP LEVEL VS. TEMPERATURE (TYPICAL) OVER CURRENT TRIP LEVEL % (NORMALIZED) 120 OVER CURRENT TRIP LEVEL % (NORMALIZED) 102 DIODE FORWARD CURRENT, IF, (AMPERES) 140 VD = 15V Tj = 25oC Tj = 125oC Tj = 25oC 120 110 100 100 101 80 90 60 80 VD = 15V 100 0 0.5 1.0 1.5 2.0 2.5 3.0 DIODE FORWARD VOLTAGE, VF, (VOLTS) 0 0 12 14 16 18 20 SUPPLY VOLTAGE, VD, (VOLTS) 0 -20 0 20 60 100 140 JUNCTION TEMPERATURE, Tj, (oC) 582 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Inverter Part FAULT OUTPUT PULSE WIDTH VS. TEMPERATURE (TYPICAL) CONTROL SUPPLY VOLTAGE TRIP-RESET LEVEL TEMPERATURE DEPENDENCY (TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 3.0 VD = 15V FAULT OUTPUT PULSE WIDTH, tfo, (ms) 15 UV UVr 101 2.5 UV TRIP-RESET LEVEL, UVt, UVr, (VOLTS) 14 100 2.0 13 10-1 1.5 12 1.0 11 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)Q = 3.0oC/W 0 -50 0 50 100 o 0 150 -50 0 50 100 o 150 10-3 10-3 10-2 10-1 TIME, (s) 100 101 JUNCTION TEMPERATURE, Tj, ( C) JUNCTION TEMPERATURE, Tj, ( C) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 101 100 10-1 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)D = 5.5oC/W 10-3 10-3 10-2 10-1 TIME, (s) 100 101 583 Powerex, Inc., 200 Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM10RSH120 IntellimodTM Module Three Phase + Brake IGBT Inverter Output 10 Amperes/1200 Volts Brake Part SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) OUTPUT CHARACTERISTICS (TYPICAL) 3.0 COLLECTOR-EMITTER SATURATION VOLTAGE VCE(sat), (VOLTS) SATURATION VOLTAGE VCE(sat), (VOLTS) 3.0 2.5 2.0 1.5 1.0 0.5 0 0 2 4 6 8 10 0 12 14 16 18 20 COLLECTOR CURRENT, IC, (AMPERES) SUPPLY VOLTAGE, VD, (VOLTS) COLLECTOR CURRENT, IC, (AMPERES) 15 Tj = 25oC VCIN = 0V 15 2.5 2.0 1.5 1.0 0.5 0 VD = 15V VCIN = 0V Tj = 25oC Tj = 125oC 10 VD = 17V 13 5 Tj = 25oC VCIN = 0V IC = 10A 0 0 1 2 3 4 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) DIODE FORWARD CHARACTERISTICS TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi) TRANSIENT IMPEDANCE, Zth(j-c), (NORMALIZED VALUE) 102 DIODE FORWARD CURRENT, IF, (AMPERES) 101 101 VD = 15V Tj = 25oC Tj = 125oC 100 100 101 10-1 10-1 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)Q = 2.0oC/W 10-2 SINGLE PULSE STANDARD VALUE = Rth(j-c)D = 5.5oC/W 100 0.5 1.0 1.5 2.0 2.5 3.0 3.5 DIODE FORWARD VOLTAGE, VF, (VOLTS) 10-3 10-3 10-2 10-1 TIME, (s) 100 101 10-3 10-3 10-2 10-1 TIME, (s) 100 101 584 |
Price & Availability of PM10RSH120
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |