MEAN WELL
SWITCHING POWER SUPPLY
ISO-9001 CERTIFIED MANUFACTURER
.LOW COST, HIGH RELIABILITY .105C OUTPUT CAPACITOR .INTERNATIONAL AC INPUT RANGE .HIGH EFFICIENCY, LOW WORKING TEMPERATURE .SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT .SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED MODEL SPECIFICATION DC OUTPUT VOLTAGE OUTPUT V. TOLERANCE OUTPUT RATED CURRENT OUTPUT MIN. CURRENT OUTPUT MAX. CURRENT RIPPLE & NOISE p-p LINE REGULATION LOAD REGULATION RATED OUTPUT POWER MAXIMUM OUTPUT POWER EFFICIENCY DC VOLTAGE ADJ. INPUT VOLTAGE RANGE AC CURRENT INRUSH CURRENT LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE PROTECTION TEMP. COEFFICIENT SETUP, RISE, HOLD UP TIME VIBRATION WITHSTAND VOLTAGE ISOLATION RESISTANCE WORKING TEMP., HUMIDITY STORAGE TEMP., HUMIDITY DIMENSION WEIGHT SAFETY STANDARDS EMC STANDARDS NOTE : PS-65-3.3 3.3V 3% 12A 0A 15.2A 80mV 1% 3% 39.6W PS-65-5 5V 3% 12A 0A 13.8A 100mV 1% 3% 60W PS-65-7.5 PS-65-12 7.5V 3% 8A 0A 9.6A 100mV 1% 3% 60W 12V 2% 5.2A 0A 6A 100mV 1% 2% 62.4W PS-6513.5 13.5V 2% 4.7A 0A 5.4A 100mV 1% 2% 63.5W .COMPACT SIZE, LIGHT WEIGHT .100% FULL LOAD BURN-IN TEST .BUILT IN EMI FILTER, LOW RIPPLE NOISE
PS-65
SERIES
PS-65-15 PS-65-24 PS-65-27 PS-65-48 15V 2% 4.2A 0A 4.8A 100mV 1% 2% 63W 24V 2% 2.7A 0A 3A 100mV 1% 2% 64.8W 27V 2% 2.4A 0A 2.7A 100mV 1% 2% 64.8W 48V 2% 1.35A 0A 1.5A 100mV 1% 2% 64.8W
RATED OUTPUT POWER FOR CONVECTION; 72W (+3.3V:50W;+5V:69W) WITH 18 CFM MIN. FORCED AIR 69% +10,-5% 90~264VAC 47~440Hz ; 120~370VDC 1.5A/115V 0.9A/230V COLD START 20A/115V 40A/230V <0.5mA/240VAC 73~105W (3.3V:51~75W)(5V:70~105W) TYPE:PULSING HICCUP SHUTDOWN RESET:AUTO RECOVERY 115%~135% 0.04% / C (0~50C) 800ms, 20ms, 20ms 10~500Hz, 2G 10min./1cycle, PERIOD FOR 60min. EACH AXES I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:500VDC / 100M Ohms -10C~+60C(REFER TO OUTPUT DERATING CURVE), 20%~90% RH -20C~+85C, 10%~95% RH 127*76.2*42mm (L*W*H) PCB ONLY 0.28Kgs UL1950, TUV EN60950 APPROVED CISPR22 (EN55022), IEC1000-4-2,3,4,5 IEC1000-3-2,3 VERIFICATION 76% 79% 79% 79% 79% 80% 80% 80%
1.ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25C 70% RH. AMBIENT. 2.TOLERANCE GINCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION. 3.RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR. 4.LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD. 5.OUTPUT PROVIDE UP TO MAXIMUM CURRENT, BUT RELATED TO MAXIMUM OUTPUT POWER. 6.MOUNTING HOLES M1 AND M2 SHOULD BE GROUNDED FOR EMI PURPOSES.
2002-04-29
|
