View SE1030W_1306806.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Applications
SONET/SDH-based transmission systems, test equipment and modules OC-48 fibre optic modules and line termination ATM optical receivers Gigabit Ethernet Fibre Channel
Product Description
SiGe Semiconductor offers a portfolio of optical networking ICs for use in high-performance optical transmitter and receiver functions, from 155 Mb/s up to 12.5 Gb/s. SiGe Semiconductor's SE1030W is a fully integrated, silicon bipolar transimpedance amplifier; providing wideband, low noise preamplification of signal current from a photodetector. It features differential outputs, and incorporates an automatic gain control mechanism to increase dynamic range, allowing input signals up to 2.6 mA peak. A decoupling capacitor on the supply is the only external circuitry required. A system block diagram is shown after the functional description, on page 3. Noise performance is optimized for 2.5 Gb/s operation, with a calculated rms noise based -10 sensitivity of -26 dBm for 10 bit error rate, achieved using a detector with 0.5 pF capacitance and a responsivity of 0.9 A/W, with an infinite extinction ratio source.
Features
Single +3.3 V power supply Input noise current = 360 nA rms when used with a 0.5 pF detector Transimpedance gain = 2.3 k into a 50 load (differential) On-chip automatic gain control gives input current overload of 2.6 mA pk and max output voltage swing of 300 mV pk-pk Differential 50 outputs Bandwidth (-3 dB) = 2.4 GHz Wide data rate range = 50 Mb/s to 2.5 Gb/s Constant photodiode reverse bias voltage = 1.5 V (anode to input, cathode to VCC) Minimal external components, supply decoupling only Operating junction temperature range = -40C to +125C Equivalent to Nortel Networks AB89-A2A

Ordering Information
Type SE1030W Package Bare Die Remark Shipped in Waffle Pack
Functional Block Diagram
SE1030 TzAmp 2.5 Gb/s
Automatic Gain Control
Integrator VCC or +ve supply
Rectifier
Input Current TZ_IN
Rf Tz Amp Output Driver
50 50
OUTP OUTN
Bandgap Reference
43-DST-01 Rev 1.5 May 24/02
1 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Bondpad Diagram
VCC
1
11
VCC
DNC
2
Top View
10 TZ_IN 3 9 OUTN OUTP
4
5
6
7
8
VEE2
VEE1
VEE1
VEE1
VCC
Bondpad Description
Pad No. 1 2 3 4 5 6 7 8 9 10 11 Name VCC DNC TZ_IN VEE2 VEE1 VEE1 VEE1 VCC OUTN OUTP VCC Description Positive supply (+3.3 V), pads 1, 8 & 11 are connected on chip. Only one pad needs to be bonded. Do not connect. Input pad (connect to photodetector anode). Negative supply (0V) - Note this is separate ground for the input stage, which is AC coupled on chip. There is no DC current through this pad. Negative supply (0V), pads 5, 6 & 7 are connected on chip. Only one pad needs to be bonded. Negative supply (0V), pads 5, 6 & 7 are connected on chip. Only one pad needs to be bonded. Negative supply (0V), pads 5, 6 & 7 are connected on chip. Only one pad needs to be bonded. Positive supply (+3.3 V), pads 1, 8 & 11 are connected on chip. Only one pad needs to be bonded. Negative differential voltage output. Positive differential voltage output. Positive supply (+3.3 V), pads 1, 8 & 11 are connected on chip. Only one pad needs to be bonded.
43-DST-01 Rev 1.5 May 24/02
2 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Functional Description Amplifier Front-End
The transimpedance front-end amplifies an input current from a photodetector, at pin TZ_IN, to produce a differential output voltage with the feedback resistor Rf determining the level of amplification (see the functional block diagram on page 1). An automatic gain control loop varies this resistor, to ensure that the output from the front-end does not saturate the output driver stage that follows. This gain control allows input signals of up to 2.6 mA peak. The input pin TZ_IN is biased at 1.5 V below the supply voltage VCC, allowing a photodetector to have a constant reverse bias by connecting the cathode to 3.3 V. This enables full single rail operation. The front-end stage has its own supply ground connection (VEE2) to achieve optimum noise performance and maintain integrity of the high-speed signal path. The front-end shares the VCC (+3.3 V)
connection with the remainder of the circuitry, which has a separate ground (VEE1).
Output driver stage
The output driver acts as a buffer stage, capable of swinging up to 300 mVpk-pk differential into a 100 load. The small output swings allow ease of use with low voltage post amplifiers (e.g. 3.3 V parts). Increasing optical input level gives a positive-going output signal on the OUTP pin.
Automatic Gain Control (AGC)
The AGC circuit monitors the voltages from the output driver and compares them to an internal reference level produced via the on-chip bandgap reference circuit. When this level is exceeded, the gain of the front-end is reduced by controlling the feedback resistor Rf. A long time-constant integrator is used within the control loop of the AGC with a typical low frequency cut-off of 5 kHz.
System Block Diagram
Receiver Module AGC Amplifier Clock Clock & Data Recovery Data LOS 2 SE1230 2
2.5 GHz
2
SE1030W
TZ Amplifier
PIN
2.5 Gb/s
2
43-DST-01 Rev 1.5 May 24/02
3 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Absolute Maximum Ratings
These are stress ratings only. Exposure to stresses beyond these maximum ratings may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. Symbol VCC VIO IIO IIO VESD VESD Tstg Supply Voltage Voltage at any input or output Current sourced into any input or output except TZ_IN Current sourced into pin TZ_IN Electrostatic Discharge (100 pF, 1.5 k) except TZ_IN Electrostatic Discharge (100 pF, 1.5 k) pin TZ_IN Storage Temperature Parameter Min -0.7 -0.5 -20 -5 -2 -0.25 -65 Max 6.0 VCC+0.5 20 5 2 0.25 150 Unit V V mA mA kV kV C
Recommended Operating Conditions
Symbol VCC Tj Supply Voltage Operating Junction Temperature Parameter Min 3.1 -40 Typ 3.3 Max 3.5 125 Unit V C
DC Electrical Characteristics
Symbol ICC max ICC zero lagc Vin Vout Rout Parameter Supply Current (max input current) Supply Current (zero input current) AGC Threshold Input Bias Voltage Output Bias Voltage Output Resistance 35 42 VCC- 1.57 VCC- 1.52 VCC- 0.30 50 65 VCC- 1.47 Min Typ 66 52 Max 101 85 Unit mA mA A pk-pk V V
43-DST-01 Rev 1.5 May 24/02
4 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
AC Electrical Characteristics
Symbol BW (3dB) Tz Dri Voutmax Flf lOL Pol Nrms Parameter Small Signal Bandwidth at -3dB point Differential Transimpedance (50 on each output, f = 100 MHz) Input Data Rate Maximum Differential Output Voltage Low Frequency Cut-off Input Current before overload (2.5 Gb/s NRZ data) Optical Overload Input Noise Current (in 2 GHz) 2600 +1.6 360 500 5 Min 1.8 1.6 50 Typ 2.4 2.3 3.1 2500 300 Max Unit GHz k Mb/s mV pk-pk kHz A pk-pk dBm nA rms
DC and AC electrical characteristics are specified under the following conditions: Supply Voltage (VCC).........................................3.1 V to 3.5 V Junction Temperature (Tj)..................................-40C to 125C Load Resistor (RL)...............................................50 AC coupled via 220 nF, for each output Photodetector Capacitance (Cd).......................0.5 pF Input bond wire inductance................................1 nH Photodetector responsivity.................................0.9 A/W Transimpedance (Tz) measured with 4 A mean photocurrent
43-DST-01 Rev 1.5 May 24/02
5 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Bondpad Configuration
The bondpad center coordinates are referenced to the center of the lower left pad (pad 4). All dimensions are in microns (m). X Coordinate (m) -307.0 -307.0 -307.0 0 134.0 364.0 498.0 697.0 697.0 697.0 697.0 Y Coordinate (m) 698.0 583.0 334.0 0 0 0 0 0 174.0 304.0 698.0
Pad No. 1 2 3 4 5 6 7 8 9 10 11
Name VCC DNC TZ_IN VEE2 VEE1 VEE1 VEE1 VCC OUTN OUTP VCC
43-DST-01 Rev 1.5 May 24/02
6 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
The diagram below shows the bondpad configuration of the SE1030W Transimpedance Amplifier. Note that the diagram is not to scale. All bondpads are 92 m x 92 m with a passivation opening of 82 m x 82 m. There are three VCC and three VEE1 pads for ease of wire bonding; the VCC and VEE1 pads respectively are connected onchip and only one pad of each type is required to be bonded out. Mechanical die visual inspection criteria per MIL-STD-883 Method 2010.10 Condition B Class Level B.
1004.0
115.0
249.0
Top View
123.0 307.0 134.0 230.0 134.0 199.0
944.0
334.0
1250.0
123.0
Side View
All Dimensions in Microns (m)
43-DST-01 Rev 1.5 May 24/02
400.0
174.0
130.0
394.0
7 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
Applications Information
Note that all VCC pads (1, 8, 11) are connected on-chip, as are the VEE1 pads (5, 6, 7), and only one pad of each type is required to be bonded out. However, in order to minimize inductance for optimum high speed performance, it is recommended that all power pads are wire bonded. The VEE2 pad is not connected on chip to VEE1 and must be bonded out separately.
+3.3 V PIN Bias 1 nF min 1 8 VCC 11 1 nF min
3 PIN
TZ Amplifier SE1030W
TZ_IN VEE2 4 5 VEE1 6 7
OUTP
10
OUTN 9 To 50 O loads, AC coupled
0V
43-DST-01 Rev 1.5 May 24/02
8 of 9
SE1030W
LightChargerTM 2.5 Gb/s Transimpedance Amplifier Final
http://www.sige.com Headquarters: Canada
Phone: +1 613 820 9244 Fax: +1 613 820 4933
2680 Queensview Drive Ottawa ON K2B 8J9 Canada sales@sige.com
U.S.A. 1150 North First Street San Jose, CA USA 95112 Phone: +1 408 998 5060 Fax: +1 408 998 5062
United Kingdom 1010 Cambourne Business Park Cambourne Cambridge CB3 6DP Phone: +44 1223 598 444 Fax: +44 1223 598 035
Product Preview The datasheet contains information from the product concept specification. SiGe Semiconductor reserves the right to change information at any time without notification. Preliminary The datasheet contains information from the design target specification. SiGe Semiconductor reserves the right to change information at any time without notification. Final The datasheet contains information from the final product specification. SiGe Semiconductor reserves the right to change information at any time without notification. Production testing may not include testing of all parameters. Information furnished is believed to be accurate and reliable and is provided on an "as is" basis. SiGe Semiconductor Inc. as sumes no responsibility or liability for the direct or indirect consequences of use of such information nor for any infringement of patents or other rights of third parties, which may result from its use. No license or indemnity is granted by implication or otherwise under any patent or other intellectual property rights of SiGe Semiconductor Inc. or third parties. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SiGe Semiconductor Inc. products are NOT authorized for use in implantation or life support applications or systems without express written approval from SiGe Semiconductor Inc. LightChargerTM is a trademark owned by SiGe Semiconductor. Copyright 2002 SiGe Semiconductor All Rights Reserved
43-DST-01 Rev 1.5 May 24/02
9 of 9

▲Up To Search▲

Price & Availability of SE1030W

	To Download SE1030W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .