|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ASAHI KASEI [AKD4359-SC] AKD4359-SC Evaluation board Rev.0 for AK4359 GENERAL DESCRIPTION The AKD4359-SC is an evaluation board for AK4539, the 24bit 8ch D/A converter. The AKD4359-SC also has the digital audio interface and can achieve the interface with digital audio systems via opt-connector or BNC connector. Ordering guide AKD4359-SC --- Evaluation board for AK4359 (Cable for connecting with printer port of IBM-AT compatible PC and control software are packed with this. This control software does not operate on Windows NT) FUNCTION Compatible with 2 types of interface DIR with optical input and BNC input Direct interface with AC3 decoder by 10pin header 10pin header for serial control interface -15V +15V Regulator GND LOUT1 Control Data ROUT1 LOUT2 ROUT2 Output Buffer DIR AK4113 10pin Header BNC In Opt In AK4359 LOUT3 AC3 ROUT3 LOUT4 10pin Header ROUT4 Figure 1. AKD4359-SC Block Diagram *Circuit diagram and PCB layout are attached at the end of this manual. ASAHI KASEI [AKD4359-SC] Operation sequence 1) Set up the power supply lines. (See "Other jumpers set-up".) Name +15V -15V AGND Color Red Blue Black Voltage +12+15V -12-15V 0V Comments Regulator, Power supply for Op-amp. Power supply for Op-amp. GND Attention This jack is always needed. Power line This jack is always needed. Power line This jack is always needed. Table 1. Set up of power supply lines Each supply line should be distributed from the power supply unit. 2) Set-up the jumper pins 3) Set-up the DIP switches. (See the followings.) 4) Power on The AK4359 should be reset once bringing SW1 (PDN) "L" upon power-up. Evaluation mode 1. DIR(COAX) (default) J1 is used for the evaluation using such as CD test disk. The DIR generates MCLK, BICK and LRCK SDATA from the received data through BNC connector (J9). Setting of jumper is shown below. COAX is recommended for an evaluation of the Sound quality. JP1 OPT COAX BNC (Default) Figure 2. Jumper setting, when using DIR 2. DIR(Optical Link) PORT1 is used for the evaluation using such as CD test disk. The DIR generates MCLK, BICK and LRCK SDATA from the received data through optical connector (PORT4: TORX176). Setting of jumper is shown below. JP1 OPT COAX PORT2 Figure 3. Jumper setting, when using DIR 2005/06 ASAHI KASEI [AKD4359-SC] DIP Switch setting [SW2]: AK4113 setting No. 1 2 Pin OCKS1 OCKS0 OFF AK4113 Master Clock setting Refer to Table4 Table 2. SW2 setting [SW3]: AK4359 setting No. 1 2 3 Pin OFF ON Default OFF OFF ON ON Default ON OFF SMUTE AK4359 setting P/S ACKS Note : When using the serial mode, R5 and R17 should be removed. Table 3. SW3 setting The frequency of the master clock output is set by OCKS0 and OCKS1 as shown in Table 4. OCKS1 0 1 1 OCKS0 0 0 1 MCLK Frequency 256fs @fs=88.2/96kHz 512fs @32/44.1/48kHz 128fs @176.4/192kHz Table 4. MCLK Clock Default SW1 setting [SW1](PDN): Reset of AK4359. Select "H" during operation. 2005/06 ASAHI KASEI [AKD4359-SC] External analog circuit The 2nd order LPF (fc=111.8kHz, Q=0.714) which adds differential outputs of the AK4359 is implemented on the board. When the further attenuation of the out-band noise is needed, some additional LPF is required. Analog signal is output through BNC connectors on the board. And the output level of the AK4359 is 5.68Vpp@5V. C1 R4 R3 +Vop 22u R1 R2 AOUT 10k C2 Analog Out -Vop fc=111.8kHz, Q=0.714, g=-0.04dB at 40kHz Figure 4. On-board analog filter R1 1.5k R2 R3 R4 C1 1.8k 2.2k 3.3k 820p Table 5. The value of R,C on this board 80kHz -0.76dB C2 820p fin 20kHz 40kHz Frequency Response 0.00dB -0.04dB Table 6. Frequency Response of LPF Amplitude = 20 log K= fc= 0= R3+R4 , R4 0 , 2 1 , 2C1C2R1R2 K [1-(f/fc) ] +[(1/Q)(f/fc)] 2 22 [dB], Q = 2fc 1 1 1 1- k + + C1 R1 C1 R2 C 2 R2 2005/06 ASAHI KASEI [AKD4359-SC] Control Software Manual Set-up of evaluation board and control software 1. Set up the AKD4359-SC according to previous term. 2. Connect IBM-AT compatible PC with AKD4359-SC by 10-line type flat cable (packed with AKD4359-SC). Take care of the direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used on Windows 2000/XP. Please refer "Installation Manual of Control Software Driver by AKM device control software". In case of Windows95/98/ME, this installation is not needed. This control software does not operate on Windows NT.) 3. Insert the CD-ROM labeled "AKD4359-SC Evaluation Kit" into the CD-ROM drive. 4. Access the CD-ROM drive and double-click the icon of "akd4396.exe" to set up the control program. 5. Then please evaluate according to the follows. Operation flow Keep the following flow. 1. Set up the control program according to explanation above. 2. Click "Port Reset" button. Explanation of each buttons 1. [Port Reset] : 2. [Write default] : 3. [All Write] : 4. [Function1] : 5. [Function2] : 6. [Function3] : 7. [Function4] : 8. [Function5]: 9. [SAVE] : 10. [OPEN] : 11. [Write] : Set up the USB interface board (AKDUSBIF-A) . Initialize the register of AK4359. Write all registers that is currently displayed. Dialog to write data by keyboard operation. Dialog to write data by keyboard operation. The sequence of register setting can be set and executed. The sequence that is created on [Function3] can be assigned to buttons and executed. The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. Save the current register setting. Write the saved values to all register. Dialog to write data by mouse operation. Indication of data Input data is indicated on the register map. Red letter indicates "H" or "1" and blue one indicates "L" or "0". Blank is the part that is not defined in the datasheet. 2005/06 ASAHI KASEI [AKD4359-SC] Explanation of each dialog 1. [Write Dialog]: Dialog to write data by mouse operation There are dialogs corresponding to each register. Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data becomes "H" or "1". If not, "L" or "0". If you want to write the input data to AK4359, click [OK] button. If not, click [Cancel] button. 2. [Function1 Dialog] : Dialog to write data by keyboard operation Address Box: Input registers address in 2 figures of hexadecimal. Data Box: Input registers data in 2 figures of hexadecimal. If you want to write the input data to AK4359, click [OK] button. If not, click [Cancel] button. 3. [Function2 Dialog] : Dialog to evaluate ATT Address Box: Input registers address in 2 figures of hexadecimal. Start Data Box: Input starts data in 2 figures of hexadecimal. End Data Box: Input end data in 2 figures of hexadecimal. Interval Box: Data is written to AK4642 by this interval. Step Box: Data changes by this step. Mode Select Box: If you check this check box, data reaches end data, and returns to start data. [Example] Start Data = 00, End Data = 09 Data flow: 00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00 If you do not check this check box, data reaches end data, but does not return to start data. [Example] Start Data = 00, End Data = 09 Data flow: 00 01 02 03 04 05 06 07 08 09 If you want to write the input data to AK4359, click [OK] button. If not, click [Cancel] button. 2005/06 ASAHI KASEI [AKD4359-SC] 4. [Save] and [Open] 4-1. [Save] Save the current register setting data. The extension of file name is "akr". (Operation flow) (1) Click [Save] Button. (2) Set the file name and push [Save] Button. The extension of file name is "akr". 4-2. [Open] The register setting data saved by [Save] is written to AK4359. The file type is the same as [Save]. (Operation flow) (1) Click [Open] Button. (2) Select the file (*.akr) and Click [Open] Button. 2005/06 ASAHI KASEI [AKD4359-SC] 5. [Function3 Dialog] The sequence of register setting can be set and executed. (1) Click [F3] Button. (2) Set the control sequence. Set the address, Data and Interval time. Set "-1" to the address of the step where the sequence should be paused. (3) Click [Start] button. Then this sequence is executed. The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step. This sequence can be saved and opened by [Save] and [Open] button on the Function3 window. The extension of file name is "aks". Figure 5. Window of [F3] 2005/06 ASAHI KASEI [AKD4359-SC] 6. [Function4 Dialog] The sequence that is created on [Function3] can be assigned to buttons and executed. When [F4] button is clicked, the window as shown in Figure 6 opens. Figure 6. [F4] window 2005/06 ASAHI KASEI [AKD4359-SC] 6-1. [OPEN] buttons on left side and [START] buttons (1) Click [OPEN] button and select the sequence file (*.aks). The sequence file name is displayed as shown in Figure 7. Figure 7. [F4] window(2) (2) Click [START] button, then the sequence is executed. 3-2. [SAVE] and [OPEN] buttons on right side [SAVE] : The sequence file names can assign be saved. The file name is *.ak4. [OPEN] : The sequence file names assign that are saved in *.ak4 are loaded. 3-3. Note (1) This function doesn't support the pause function of sequence function. (2) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (3) When the sequence is changed in [Function3], the file should be loaded again in order to reflect the change. 2005/06 ASAHI KASEI [AKD4359-SC] 7. [Function5 Dialog] The register setting that is created by [SAVE] function on main window can be assigned to buttons and executed. When [F5] button is clicked, the following window as shown in Figure 8opens. Figure 8. [F5] window 7-1. [OPEN] buttons on left side and [WRITE] button (1) Click [OPEN] button and select the register setting file (*.akr). (2) Click [WRITE] button, then the register setting is executed. 7-2. [SAVE] and [OPEN] buttons on right side [SAVE] : The register setting file names assign can be saved. The file name is *.ak5. [OPEN] : The register setting file names assign that are saved in *.ak5 are loaded. 7-3. Note (1) All files need to be in same folder used by [SAVE] and [OPEN] function on right side. (2) When the register setting is changed by [Save] Button in main window, the file should be loaded again in order to reflect the change. 2005/06 ASAHI KASEI [AKD4359-SC] MEASUREMENT RESULTS [Measurement condition] * Measurement unit : Audio Precision, System two, Cascade * MCLK : 512fs, 256fs, 128fs * BICK : 64fs * fs : 44.1kHz, 96kHz, 192kHz * BW : 10Hz20kHz (fs=44.1kHz), 10Hz40kHz (fs=96kHz), 10Hz40kHz (fs=192kHz) * Bit : 24bit * Power Supply : AVDD=DVDD=5V * Interface : DIR (AK4113) * Temperature : Room fs=44.1kHz Parameter S/(N+D) DR S/N Input signal 1kHz, 0dB 1kHz, -60dB no signal Measurement filter 20kLPF 20kLPF 22kLPF, A-weighted 20kLPF 22kLPF, A-weighted Lch 98.4dB 102.8dB 106.5dB 102.8dB 106.2dB Rch 98.4dB 102.8dB 106.5dB 102.8dB 106.2dB fs=96kHz Parameter S/(N+D) DR S/N Input signal 1kHz, 0dB 1kHz, -60dB no signal Measurement filter 40kLPF 40kLPF 22kLPF, A-weighted 40kLPF 22kLPF, A-weighted Lch 97.0dB 101.0dB 105.9dB 101.0dB 106.0dB Rch 97.0dB 101.0dB 106.0dB 101.0dB 106.0dB fs=192kHz Parameter S/(N+D) DR S/N Input signal 1kHz, 0dB 1kHz, -60dB no signal Measurement filter 40kLPF 40kLPF 22kLPF, A-weighted 40kLPF 22kLPF, A-weighted Lch 97.5dB 101.5dB 106.0dB 101.5dB 106.0dB Rch 97.5dB 101.5dB 106.0dB 101.5dB 106.0dB 2005/06 ASAHI KASEI [AKD4359-SC] (fs=44.1kHz) AK4359 FFT fs=44.1kHz AVDD=DVDD=5V, 0dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 Hz 1k 2k 5k 10k 20k Figure 9. FFT (1kHz, 0dBFS input) AK4359 FFT fs=44.1kHz AVDD=DVDD=5V, -60dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 Hz 1k 2k 5k 10k 20k Figure 10. FFT (1kHz, -60dBFS input) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=44.1kHz) AK4359 FFT fs=44.1kHz AVDD=DVDD=5V, No input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 Hz 1k 2k 5k 10k 20k Figure 11. FFT (noise floor) AK4359 FFT fs=44.1kHz AVDD=DVDD=5V, Out of band noise +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 20 50 100 200 500 1k Hz 2k 5k 10k 20k 50k 100k Figure 12. FFT (out-of-band noise) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=44.1kHz) AK4359 THD+N vs Input Level fs=44.1kHz AVDD=DVDD=5V -80 -82 -84 -86 -88 -90 -92 d B r A -94 -96 -98 -100 -102 -104 -106 -108 -110 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 13. THD+N vs Input Level (fin=1kHz) AK4359 THD+N vs Input Frequency fs=44.1kHz AVDD=DVDD=5V -70 -72.5 -75 -77.5 -80 -82.5 -85 d B r A -87.5 -90 -92.5 -95 -97.5 -100 -102.5 -105 -107.5 -110 20 50 100 200 500 Hz 1k 2k 5k 10k 20k Figure 14. THD+N vs fin (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=44.1kHz) AK4359 Linearity fs=44.1kHz AVDD=DVDD=5V +0 -10 -20 -30 -40 -50 d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 15. Linearity (fin=1kHz) AK4359 Frequency Respons fs=44.1kHz AVDD=DVDD=5V +1 +0.8 +0.6 +0.4 +0.2 d B r A +0 -0.2 -0.4 -0.6 -0.8 -1 2k 4k 6k 8k 10k Hz 12k 14k 16k 18k 20k Figure 16. Frequency Response (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=44.1kHz) AK4359 Crosstalk fs=44.1kHz AVDD=DVDD=5V -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 20 50 100 200 500 Hz 1k 2k 5k 10k 20k Figure 17. Cross-talk (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AK4359 FFT fs=96kHz AVDD=DVDD=5V, 0dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 18. FFT (1kHz, 0dBFS input) AK4359 FFT fs=96kHz AVDD=DVDD=5V, -60dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 19. FFT (1kHz, -60dBFS input) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AK4359 FFT fs=96kHz AVDD=DVDD=5V, No input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 20. FFT (noise floor) AK4359 FFT fs=96kHz, Notch AVDD=DVDD=5V, 0dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 21. FFT (Notch) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AK4359 THD+N vs Input Level fs=96kHz AVDD=DVDD=5V -80 -82 -84 -86 -88 -90 -92 d B r A -94 -96 -98 -100 -102 -104 -106 -108 -110 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 22. THD+N vs Input Level (fin=1kHz) AK4359 THD+N vs Input Frequency fs=96kHz AVDD=DVDD=5V -70 -72.5 -75 -77.5 -80 -82.5 -85 d B r A -87.5 -90 -92.5 -95 -97.5 -100 -102.5 -105 -107.5 -110 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 23. THD+N vs fin (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AK4359 Linearity fs=96kHz AVDD=DVDD=5V +0 -10 -20 -30 -40 -50 d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 24. Linearity (fin=1kHz) AK4359 Frequency Respons fs=96kHz AVDD=DVDD=5V +1 +0.8 +0.6 +0.4 +0.2 d B r A +0 -0.2 -0.4 -0.6 -0.8 -1 2.5k 5k 7.5k 10k 12.5k 15k 17.5k 20k Hz 22.5k 25k 27.5k 30k 32.5k 35k 37.5k 40k Figure 25. Frequency Response (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AK4359 Crosstalk fs=96kHz AVDD=DVDD=5V -80 -85 -90 -95 -100 -105 d B -110 -115 -120 -125 -130 -135 -140 40 50 100 200 500 1k Hz 2k 5k 10k 20k 40k Figure 26. Cross-talk (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=192kHz) AK4359 FFT fs=192kHz AVDD=DVDD=5V, 0dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k Figure 27. FFT (1kHz, 0dBFS input) AK4359 FFT fs=192kHz AVDD=DVDD=5V, -60dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k Figure 28. FFT (1kHz, -60dBFS input) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=192kHz) AK4359 FFT fs=192kHz AVDD=DVDD=5V, No input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k Figure 29. FFT (noise floor) AK4359 FFT fs=192kHz, Notch AVDD=DVDD=5V, 0dBFS input +0 -10 -20 -30 -40 -50 -60 d B r A -70 -80 -90 -100 -110 -120 -130 -140 -150 -160 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k Figure 30. FFT (Notch) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=192kHz) AK4359 THD+N vs Input Level fs=192kHz AVDD=DVDD=5V -80 -82 -84 -86 -88 -90 -92 d B r A -94 -96 -98 -100 -102 -104 -106 -108 -110 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 31. THD+N vs Input Level (fin=1kHz) AK4359 THD+N vs Input Frequency fs=192kHz AVDD=DVDD=5V -70 -72.5 -75 -77.5 -80 -82.5 -85 d B r A -87.5 -90 -92.5 -95 -97.5 -100 -102.5 -105 -107.5 -110 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k Figure 32. THD+N vs fin (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=192kHz) AK4359 Linearity fs=192kHz AVDD=DVDD=5V +0 -10 -20 -30 -40 -50 d B r A -60 -70 -80 -90 -100 -110 -120 -130 -140 -140 -130 -120 -110 -100 -90 -80 -70 dBFS -60 -50 -40 -30 -20 -10 +0 Figure 33. Linearity (fin=1kHz) AKM +1 +0.8 +0.6 +0.4 +0.2 +0 -0.2 d B r A -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 5k 10k 15k 20k AK4359 Frequency Respons fs=192kHz AVDD=DVDD=5.0V 25k 30k 35k 40k Hz 45k 50k 55k 60k 65k 70k 75k 80k Figure 34. Frequency Response (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] (fs=96kHz) AKM -70 -75 -80 -85 -90 -95 -100 d B -105 -110 -115 -120 -125 -130 -135 -140 90 200 500 1k 2k Hz 5k 10k 20k 50k 80k AK4359 Crosstalk fs=192kHz AVDD=DVDD=5.0V Figure 35. Cross-talk (Input level=0dBFS) 2005/06 ASAHI KASEI [AKD4359-SC] Revision History Date (YY/MM/DD) 05/06/30 Manual Board Revision Revision KM079600 0 Reason First edition Contents IMPORTANT NOTICE * These products and their specifications are subject to change without notice. Before considering any use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized distributor concerning their current status. * AKM assumes no liability for infringement of any patent, intellectual property, or other right in the application or use of any information contained herein. * Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. * AKM products are neither intended nor authorized for use as critical components in any safety, life support, or other hazard related device or system, and AKM assumes no responsibility relating to any such use, except with the express written consent of the Representative Director of AKM. As used here: (a) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. (b) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. * It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or otherwise places the product with a third party to notify that party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. 2005/06 1 T1 NJM78M05FA R1 R2 100 EXT_LRCK 100 EXT_BICK R3 100 EXT_MCLK SDTI1 SDTI2 SDTI3 SDTI4 R201 DVDD + C1 C2 OUT GND 3 IN 1 +15V C3 47u 0.1u T2 NJM78M05FA 2 0.1u short GND 3 + C4 C6 OUT IN 1 C7 + C5 MCLK BICK LRCK SDATA SDTI4 1 2 3 4 5 PORT1 10 9 8 7 6 R6 SDTI1 SDTI2 SDTI3 R5 R8 R10 100 100 100 100 R4 R7 R9 R11 100K 100K 100K 100K AVDD VOP+ 47u 0.1u 2 0.1u 470u AC3 MCLK 1 BICK 2 LRCK 3 SDATA 4 AD/ROM 5 PORT2 10 9 8 7 6 -15V R12 0_C R13 0_C R14 0_C R15 0_C EXT R16 D3V 10k R17 open R18 0_C VOP470u C9 C10 + U1 1 2 3 4 5 MCLK BICK SDTI1 LRCK RSTB SMUTE/CSN/CAD0 ACKS/CCLK/SDL DIF0/CDTI/SDA SDTI2 SDTI3 SDTI4 DIF1 DEM0 DVDD DVSS DZF1 DZF2 AVDD AVSS VCOM LOUT1 ROUT1 P/S LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 DEM/I2C 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 C11 + C12 A EXT DIR C8 4113_SDTO R19 open 10_C 0_C EXT_MCLK 4113_MCLK A EXT DIR 0_C R20 R23 0_C R21 open R24 R26 0_C R25 EXT_BICK 4113_BICK EXT DIR SDTI1 5.1 100 100 100 MCLK BICK SDTI1 LRCK R27 R28 AVDD 4113_LRCK EXT_LRCK DIR EXT open R22 6 7 8 LOUT1 ROUT1 0.1u 10u SDTI2 SDTI3 SDTI4 for U11 DVDD DVDD C15 R29 R30 R31 100 100 100 SDTI2 SDTI3 SDTI4 9 10 11 12 13 14 LOUT2 ROUT2 LOUT3 ROUT3 LOUT4 ROUT4 0.1u PDN 0.1u 5.1 R32 + C16 C17 15 10u 0.1u AK4359 D3V R33 PORT3 9 7 5 3 1 uP-I/F R34 SMUTE S1 R35 10k CSN CCLK CDTI 10k 10k R37 470 2 3 5 6 11 10 14 13 1 15 SMUTE 1 2 P/S ACKS 3 U11 1A 1B 2A 2B 3A 3B 4A 4B A/B G 74LVC157 47k 1 4 1Y 2Y 3Y 4Y 4 7 9 12 RP1 4 3 2 1 MODE1 8 7 6 5 D3V 10 8 6 4 2 R36 R38 470 470 ACKS P/S SMUTE P/S ACKS Title AKD4359-SC Size A3 Date: Document Number AK4359 Wednesday, July 06, 2005 Sheet 1 of 3 + + P/S C13 C14 10u Rev 0 1 C19 C18 820p C101 C102 820p C109 C110 100p R39 open R40 100p R41 open R42 3.3k 2.2k R43 3.3k 2.2k R44 short 4 J1 R48 + 4 short C21 R45 R46 R47 C20 J2 R52 + C26 R55 8 short + 10u R54 C27 R56 820p C28 20k 820p C29 8 10k 100p R57 C30 820p C103 C104 100p R59 3.3k 4 J3 R66 + 4 C38 R73 8 short + 10u R71 C39 R74 8 820p C40 10k 100p A C46 820p C105 C106 C47 820p C113 C114 100p R75 open R76 100p R78 R77 short open R79 3.3k 2.2k 3.3k 2.2k R80 4 J6 short 8 + short R91 820p C56 20k R92 C55 10k 820p C57 8 C54 10u R89 short 100p R93 short 10k 100p R94 short C58 820p C107 C108 C59 820p C115 C116 100p R95 open R96 100p R97 3.3k 2.2k 3.3k 4 J7 8 R108 820p C68 C67 R110 8 C66 + short 10u R106 20k short 10k 820p C69 100p 10k 100p 1 + + + ROUT2 5 R107 U4B NJM4580 C62 22u 1.5k 1.8k NC 5 ROUT4 - 7 U6B NJM4580 + R99 22u 1.5k 1.8k NC - + C60 R100 R101 C61 4 R102 6 220 ROUT2 C63 R103 R104 C64 7 6 + + + LOUT2 3 R85 U4A NJM4580 C50 22u 1.5k 1.8k NC 3 LOUT4 - 1 U6A NJM4580 + R81 22u 1.5k 1.8k NC - + C48 R82 R83 C49 4 R84 2 220 LOUT2 C51 R90 R86 C52 J5 R87 1 2 220 LOUT4 C53 10u R88 20k open R98 2.2k J8 R105 220 ROUT4 C65 10u R109 20k Title Size A2 Date: Document Number + + ROUT1 U3B NJM4580 C34 short + 5 20k 820p C41 10k 100p + R63 22u 1.5k 1.8k NC - C32 R64 R65 C33 6 220 R67 22u 1.5k 1.8k NC 5 7 ROUT3 - 7 U5B NJM4580 + + LOUT1 U3A NJM4580 C22 short + 3 10k 100p R58 short short C31 820p C111 C112 open R60 100p R61 2.2k 3.3k ROUT1 C35 R68 R69 C36 6 + 22u 1.5k 1.8k NC - 2 220 R49 22u 1.5k 1.8k NC 3 1 LOUT3 R62 LOUT1 C23 R50 R51 C24 2 220 LOUT3 1 U5A NJM4580 C25 10u R53 20k open 2.2k J4 R70 220 ROUT3 C37 10u R72 20k VOPVOP+ C42 0.1u 10u C43 C44 0.1u + C45 10u A AKD4359-SC AK4359 Sheet 2 of 3 Rev 0 Friday, July 01, 2005 1 1 D1 HSU119 R111 10k SW2 OCKS1 1 2 U9A 74HC14 3 4 U9B 74HC14 L H L H 256fs@fs=88.2k/96kHz 128fs@fs=176.4k/192kHz H OCKS0 L Master Clock 512fs@fs=32k/44.1k/48kHz L 3 1 SW1 PDN 2 2 H C70 0.1u PDN for 74HC14 R202 short T3 upc3533HF GND 3 OUT IN 1 C73 0.1u C74 47u + VOP+ R112 5.1 C75 10u D3V + C76 0.1u 2 C77 0.1u 3 1 SW2 U10 1 2 OCKS DVDD CM0/CDTO/CAD1 30 4 3 OCKS1 OCKS0 C71 0.1u C72 0.1u DVSS CM1/CDTI/SDA 29 TVDD OCKS1/CCLK/SCL 28 R114 10k R115 10k 4 V/TX OCKS0/CSN/CAD0 27 5 XTI MCKO1 26 4113_MCLK 6 XTO MCKO2 25 A 7 R113 15k 8 C78 10u 9 + C79 0.1u 10 PDN DAUX 24 2 A R BICK 23 4113_BICK AVDD SDTO 22 4113_SDTO AVSS LRCK 21 TEST1 4113_LRCK 11 RX1 INT0 20 12 RX2/DIF0 FS96/I2C 19 13 RX3/DIF1 P/SN 18 14 J9 COAX C80 0.1u COAX 15 RX4/DIF2 INT1 17 RX5 RX6/IPS 16 R116 75 JP1 RX AK4113 OPT 2 L3 short VCC GND OUT DIR 3 2 1 C81 0.1u R117 short Title 1 PORT4 AKD4359-SC Size A3 Date: 1 Document Number AK4359 Friday, June 24, 2005 Sheet 3 of 3 Rev 0 |
Price & Availability of AKD4359-SC |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |