View TM162ABCW6-2_4146322.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SPECIFICATION FOR LCD MODULE
Model No.
TM162ABCW6-2
Prepared by: Checked by : Verified by : Approved by:
Date: Date: Date: Date:
TIANMA MICROELECTRONICS CO., LTD
REVISION RECORD Date Ref. Page Revision No. Revision Items Check & Approval
1/22
1. General Specifications: 1.1 Display type: STN 1.2 Display color*: Display color: Blue-Black Background: Yellow-Green 1.3 Polarizer mode: Transflective/Positive 1.4 Viewing Angle: 6:00 1.5 Driving Method: 1/16 Duty 1/5 Bias 1.6 Backlight: LED 1.7 Controller: S6A0069X01-C0CX (KS0066UP-00CC) 1.8 Display Fonts: 5 x 7 dots + 5 x 1 Cursor (1 Character) 1.9 Data Transfer: 8 Bit Parallel 1.10 Operating Temperature: -20----+70 Storage Temperature: -30----+80 1.11 Outline Dimensions: Refer to outline drawing on next page 1.12 Dot Matrix: 16 Characters X 2 Lines 1.13 Dot Size: 0.55X0.50(mm) 1.14 Dot Pitch: 0.60X0.55 (mm) 1.15 Font Size: 2.95X4.35(mm) 1.16 Font Pitch: 3.65X5.05 (mm) 1.17 Weight: 32g
* Color tone is slightly changed by temperature and driving voltage.
2/22
3. LCD Module Part Numbering System
TM 1 6 2 A B C W6 - 2
OPTIONAL IC INDICATOR (FOR FACTORY USE) MODIFICATION CODE DESIGNATOR WIDE TEMPERATURE RANGE BACKLIGHT TYPE C: TRANSFLECTIVE, LED BACKLIGHT LCD TYPE B: Y-G MODE STN, POSITIVE MODULE SERIES MODULE TYPE 3 DIGITS INDICATING 16 CHARACTERS X 2 LINES T: TIANMA M: MODULE
4/22
, '-#!

5. Absolute Maximum Ratings Item Power Supply Voltage LCD Driving Voltage Operating Temperature Range Storage Temperature Range Symbol VDD VSS VLCD TOP Min. -0.3 -0.3 Max. 7.0 V 13.0 Unit Remark
-20
+70
No Condensation
TST
-30
+80
6/22
6. Electrical Specifications and Instruction Code 6.1 Electrical characteristics Item Supply Voltage (Logic) Supply Voltage (LCD Drive) High Symbol VCC VSS Min. Typ. Max. Unit
4.5
5.0
5.5
V
VLCD VIH VCC=5.0
-
4.7
-
V
Input Signal Voltage
0.7VDD
-
VDD+0.3
V
Low
VIL VCC=5.0 IDD VCC VSS =5.0 IEE IDD VLED =4.2
-0.3
-
0.2VDD
V
Supply current (Logic) Supply current (LCD Drive) Supply current (LED Drive)
-
1.5
-
mA
-
0.40 -
138.6
mA mA
7/22
6.2 Interface Signals Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
15 16
Symbol Vss Vcc Vee RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 A K
Level 0V 5.0V 0.3V H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L H/L 4.2V 0V
Description Ground Power supply voltage for logic and LCD(+) Power supply voltage for LCD(-) Selects registers (H: Data L: Instruction) Selects read or write Data read/write enable signal Data bit0 Data bit1 Data bit2 Data bit3 Data bit4 Data bit5 Data bit6 Data bit7 Power supply voltage for LED(+) Power supply voltage for LED(-)
8/22
6.3 Interface Timing Chart AC Characteristics(V=4.5V~5.5V,Ta=-30~+85
0RGH :ULWHy0RGH o5HIHUyWRy)LJco 5HDGy0RGH o5HIHUyWRy)LJaeo
&KDUDFWHULVWLF (y&\FOHy7LPH (y5LVHyiy)DOOy7LPH (y3XOVHy:LGWKyo+LJKny/RZo 5i:yDQGy56y6HWXSy7LPH 5i:yDQGy56y+ROGy7LPH 'DWDy6HWXSy7LPH 'DWDy+ROGy7LPH (y&\FOHy7LPH (y5LVHyiy)DOOy7LPH (y3XOVHy:LGWKyo+LJKny/RZo 5i:yDQGy56y6HWXSy7LPH 5i:yDQGy56y+ROGy7LPH 'DWDy2XWSXWy'HOD\y7LPH 'DWDy+ROGy7LPH
7
0LQi eii eei ei ii ai ii eii eei ei ii e 7\Si 0D[i ei ei iei QV QV 8QLW
6\PERO WF W5nW) WZ WVXi W+i WVXe W+e WF W5nW) WZ WVX W+ W' W'+
56 5i: ( '%ia'%ae 56 5i: ( '%ia'%ae
9 , +i 9 , /i W68i 9 , /i 9 , +i 9 , /i WU 9 , +i 9 , /i
W Ki 9 , /i WI W Ke 9 , +i 9 , /i 9 , /i
WZ 9 , +i 9 , /i
W Ki
W 68e
9DOLG 'DWD W&
)LJXUHycyiyy:ULWHy0RGHy7LPLQJy'LDJUDP
9,+i 9,/i 9,+i
W68
WK 9 , +i WZ 9 , +i 9 , /i 9 , +i 9 , /i 9,+i 9,/i WK WI 9,/i 9,+i 9,/i
WU
W'
W' +
9DOLG 'DWD W&
)LJXUHyaeyiyy5HDGy0RGHy7LPLQJy'LDJUDP

+(>1
,QVWUXFWLRQy&RGH ([HFXWLRQy ,QVWUXFWLRQ 'HVFULSWLRQ WLPHyoIRVF y 56 5i: '%ae '%c '%e '%e '%e '%e '%i '%i eaeiyN+]o &OHDU y:ULWHy|ei+yWRy''5$0yDQGyVHWy i i i i i i i i i i iieeyPVy 'LVSOD\ y''5$0yDGGUHVVyWRy|ii+yIURPy$& y6HWy''5$0yDGGUHVVyWRy|ii+y yIURPy$&yDQGyUHWXUQyFXUVRUyWRyLWV 5HWXUQy i i i i i i i i i yRULJLQDOySRVLWLRQyLIyVKLIWHGiy iieeyPV +RPH y7KHyFRQWHQWVyRIy''5$0yDUHyQRWy yFKDQJHGi (QWU\y0RGHy y$VVLJQyFXUVRUyPRYLQJyGLUHFWLRQy i i i i i i i i ,i' 6+ eayPV 6HWy yDQGyHQDEOHyWKHyVKLIWyRIyHQWLUHyGLVSOD\iy y6HWyGLVSOD\o'onyFXUVRUo&ony 'LVSOD\y21i eayPV i i i i i i i ' & % yDQGyEOLQNLQJyRIyFXUVRUo%oyRQiRIIy 2))y&RQWURO yFRQWUROyELWi y6HWyFXUVRUyPRYLQJyDQGyGLVSOD\y &XUVRUyRU eayPV i i i i i i 6i& 5i/ yVKLIWyFRQWUROyELWnyDQGyWKHyGLUHFWLRQny y'LVSOD\y 6KLIW yZLWKRXWyFKDQJLQJyRIy''5$0yGDWDiy y6HWyLQWHUIDFHyGDWDyOHQJWKyo'/ay yaELWieELWonyQXPEHUVyRIyGLVSOD\yOLQH eayPV i i i i '/ 1 ) y )XQFWLRQy6HW i yo1ayeOLQHiiOLQHoyDQGnyGLVSOD\ yIRQWyW\SHyo)aeuiiGRWVieuayGRWVo y6HWy&*5$0yDGGUHVVyLQyDGGUHVVy 6HWy&*5$0y i i i i $&e $&e $&e $&e $&i $&i eayPV yFRXQWHUi $GGUHVV 6HWy''5$0y y6HWy''5$0yDGGUHVVyLQyDGGUHVVy eayPV i i i $&c $&e $&e $&e $&e $&i $&i $GGUHVV yFRXQWHUi y:KHWKHUyGXULQJyLQWHUQDOyRSHUDWLRQ 5HDGy%XV\y yRUyQRWyFDQyEHyNQRZQyE\yUHDGLQJy%)iy i i %) $&c $&e $&e $&e $&e $&i $&i iyPV )ODJyDQGy y7KHyFRQWHQWVyRIyDGGUHVVyFRXQWHU $GGUHVV yFDQyDOVRyEHyUHDGi :ULWHy'DWDyWRy y:ULWHyGDWDyLQWRyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV 5$0 yo''5$0i&*5$0oi 5HDGy'DWDy y5HDGyGDWDyIURPyLQWHUQDOy5$0y i i 'ae 'c 'e 'e 'e 'e 'i 'i eeyPV IURPy5$0 yo''5$0i&*5$0oi yyyyyyyyyyyyoy||ayGRQ(c)WyFDUH 127(ay:KHQyDQy038ySURJUDPyZLWKyFKHFNLQJyWKHy%XV\y)ODJo'%aeoyLVyPDGHnyLWyPXVWyEHyQHFHVVDU\yiie)RVFyLV yyyyyyyyyyyyyQHFHVVDU\yIRUyH[HFXWLQJyWKHyQH[WyLQVWUXFWLRQyE\yWKHyIDOOLQJyHGJHyRIyWKHyo(oyVLJQDOyDIWHUyWKHy%XV\y)ODJyo'%aeoy yyyyyyyyyyyyyJRHVyWRy|/RZiy
yy,QVWUXFWLRQy7DEOH

)+0-;:,6D**))?**7 )+0-;:,6D**))?**7

7. Optical Characteristics 7.1 Optical Characteristics Item Symbol Condition Min. Typ. Ta=25 Max. Unit
x
y=0
-35
--
20 Deg
Viewing Angle
y
Cr 2
x=0
-30
--
30
Contrast Ratio Turn on Turn off
Cr
x=0 y=0
4.0
-
-
Ton
x=0 y=0
-
-
250 ms
Response Time
Toff
-
-
250
13/22
7.2 Definition of Optical Characteristics 7.2.1 Definition of Viewing Angle Top Top
Bottom 7.2.2 Definition of Contrast Ratio
Bottom
Contrast Ratio = B2/B1 =
Measuring Conditions: 1) Ambient Temperature: 25 ; 7.2.3 Definition of Response time
unselected state brightness selected state brightness
2) Frame frequency: 64Hz
Turn on time: t on = t d + t r Turn off time: t off = t d + t f Measuring Condition: 1) LCD Operating Voltage: 4.7V 2) Frame frequency: 64Hz
14/22
2## 92$>@
C, A# 2$ B.# 0
... *+ #$# 3*B /# 0
. + #$# 3*B 0
. B.# 5% 8 ,+ = ..#. 3*B #$# 0
. /# + ' = 3*B #$# 0
... '+ B.# , #...#
3+H>B &B#
$# 3*B 0
. ..#
# + &*+ + , *+ , * 2
+# ,# +# ,# +

1 9 3

(@ 58 . 58 )#. !
0
. %@ 0
.. 0
. #. @
+B"D,+B"E ,+#&E '+# B$%E ++#&E # '+! *B
9:I#2 2 A# $ 0 $ -. $ = 2. >#

A# ' , * 1 9 3
:I#2
=$.@$ =$. $ =$.#. $

=$.$
:#$9 $ C = $ < -. $
345*67** 0;# )C, 5.8 A - -; 7 A/ )J/
-K + AA - , -K + AA - , -K$ =###E.E#E/ -$ =. #$#99 7 # # 0;
. E . );) ( @
A /2,# 7 # #
. E
);
$

10. Precautions for Use of LCD Modules 10.1 Handling Precautions 10.1.1 The display panel is made of glass. Do not subject it to a mechanical shock by dropping it from a high place, etc. 10.1.2 If the display panel is damaged and the liquid crystal substance inside it leaks out, be sure not to get any in your mouth, if the substance comes into contact with your skin or clothes, promptly wash it off using soap and water. 10.1.3 Do not apply excessive force to the display surface or the adjoining areas since this may cause the color tone to vary. 10.1.4 The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle this polarizer carefully. 10.1.5 If the display surface is contaminated, breathe on the surface and gently wipe it with a soft dry cloth. If still not completely clear, moisten cloth with one of the following solvents: Isopropyl alcohol Ethyl alcohol Solvents other than those mentioned above may damage the polarizer. Especially, do not use the following: Water Ketone Aromatic solvents 10.1.6 Do not attempt to disassemble the LCD Module. 10.1.7 If the logic circuit power is off, do not apply the input signals. 10.1.8 To prevent destruction of the elements by static electricity, be careful to maintain an optimum work environment. a. Be sure to ground the body when handling the LCD Modules. b. Tools required for assembly, such as soldering irons, must be properly ground. c. To reduce the amount of static electricity generated, do not conduct assembly and other work under dry conditions. d. The LCD Module is coated with a film to protect the display surface. Be care when peeling off this protective film since static electricity may be generated.
18/22
10.2 Storage precautions 10.2.1 When storing the LCD modules, avoid exposure to direct sunlight or to the light of fluorescent lamps. 10.2.2 The LCD modules should be stored under the storage temperature range. If the LCD modules will be stored for a long time, the recommend condition is: Temperature : 0 40 Relatively humidity: 80% 10.2.3 The LCD modules should be stored in the room without acid, alkali and harmful gas. 10.3 The LCD modules should be no falling and violent shocking during transportation, and also should avoid excessive press, water, damp and sunshine.
19/22
Appendix A Inspection items and criteria for appearance defects Items Leakage Rainbow Wrong polarizer attachment Polarizer Bubble between polarizer and glass Scratches of polarizer Black spot (in viewing area) Contents Criteria Not permitted According to the limit specimen Not permitted Not counted <0.3mm Max. 3 defects allowed 0.3mm 0.5mm
According to the limit specimen Not counted Max. 3 spots allowed X<0.2mm X=(a+b)/2 0.2mm X 0.5mm Max. 3 spots (lines) allowed
Black line (in viewing area)
Not counted
Max. 3 lines allowed 0.02mm a 0.05mm b 2.0mm
a<0.02mm
Progressive cracks
Not permitted
20/22
Appendix B Inspection items and criteria for display defects Items Contents Criteria Not permitted Not permitted Not permitted According to the limit specimen According to the limit specimen Not counted X<0.1mm X=(a+b)/2 Pin holes and cracks in segment (DOT) Not counted A<0.1mm Max.2 dots allowed 0.1mm A 0.2mm D<0.25mm Max.3 dots allowed 0.1mm X 0.2mm Max.3 dots allowed
Open segment or open common Short Wrong viewing angle Contrast radio uneven Crosstalk
Black spot (in viewing area)
Not counted X<0.1mm X=(a+b)/2
Max.3 spots allowed 0.1mm X 0.2mm Max.3 spots (lines) allowed
Black line (in viewing area)
Not counted a<0.02mm
Max.3 lines allowed 0.02mm a 0.05mm b 0.5mm
21/22
Appendix B Inspection items and criteria for display defects (continued) Items Content Criteria Not counted x 0.1mm x=(a+b)/2 Max. 2 defects allowed 0.1mm x 0.2mm
Not counted a 0.1mm Transformation of segment
Max. 1 defects allowed 0.1mm a 0.2mm D>0
Max.3 defects allowed
Max.2 defects allowed 0.8W a 1.2W
a=measured value of width W=nominal value of width
22/22

▲Up To Search▲

Price & Availability of TM162ABCW6-2

	To Download TM162ABCW6-2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .