 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Contactless Pushbuttons Series FP01 Distinctive Characteristics Brilliant illumination for highly visible status indication with LEDs and caps in red, green, or amber; subdued illumination for low light requirements with white cap over red, green, or amber LEDs. Photo interrupter, rather than contacts, ensures high reliability and long life of 3 million operations minimum. Rugged construction and smooth actuation allow repeated, rapid actuation force anywhere on cap surface. Snap-in mounting for easy installation. Connector socket with 6 pins for simple connection. Well suited for gaming and vending machines, as well as equipment exposed to corrosive gases used in environments such as chemical or steel manufacturing plants. Actual Size FP01-15 NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Contactless Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE Series FP01 FP01 1 5 C A C1 F F PHOTO TRANSISTOR 1 Single C SHAPE Round C1 RECEPTACLE 6-pin Socket C D F See Plug Options. LEDS Red Amber Green PHOTO INTERRUPTER 5 Unshaded (Shaded) (Momentary Operating Function) HOUSING A Black ACTUATOR COLORS B C D F White Red Amber Green C2 C3 No Code PLUG OPTIONS Assembled Connector Plug with Wire Leads Unassembled Connector Plug and Pins No Connector Plug Contact factory for custom options. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE FP0115CAC1FF Green Actuator with Green LED Single Photo Transistor with Normally Unshaded Photo Interrupter Round, Black Housing No Connector Plug NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Contactless Pushbuttons ACTUATOR & INTERRUPTER Actuator Position Normal Model FP0115 Down Photo Interrupter Unshaded Shaded Normally Unshaded with Momentary Shaded status Series FP01 Schematics 1 Single Photo Transistor 5 LED connector pins are 5 & 6; interrupter connector pins are 3-4 & 1-2. 6 4 2 5 3 1 When shaded, the photo transistor momentarily activates electrical function which signals the external device to change its state. HOUSING SHAPE & COLOR C Round Shape A Black Housing INTERNAL RECEPTACLE C1 Receptacle Internal male connector socket 654321 SWITCH SPECIFICATIONS Actuator Up Status of Photo Interrupter: Collector Current IC: Status of Photo Transistor: Output Condition of Photo Transistor: Unshaded 0.8mA minimum On IF = 20mA & VCE = 5V Actuator Down Shaded 10A maximum Off MECHANICAL SPECIFICATIONS Total Travel: Operating Force: Mechanical Life: Operating Temperature Range: .079" (2.0mm) 0.75 N (.169 lbf) 3,000,000 operations minimum -25C through +50C (-13F through +122F) MATERIALS Actuator: Housing: Polyacetal Polyamide NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Contactless Pushbuttons PHOTO INTERRUPTER SPECIFICATIONS Electrical & Optical Characteristics Input Forward Voltage VF: Reverse Current IR: Transmission Collector-Emitter Saturation Voltage VCE sat: 0.4V 1.3V 1.6V 10A Typical Maximum Series FP01 (Temperature @ 25C) Condition IF = 50mA FR = 5V IF = 20mA & IC = 0.1mA Absolute Maximum Ratings Input LED Forward Current IF: Reverse Voltage VR: Power Dissipation PD: 50mA 5V 80mW Output Photo Transistor Collector-Emitter Voltage VCEO: Emitter-Collector Voltage VECO: Collector Current IC: Collector Dissipation PC: 30V 4.5V 30mA 80mW Circuit Design Considerations VCC = 5V Output of the infrared LED in the photo interrupter decreases approximately 50% after 100,000 hours. Recommended load resistance (RL) is 40k ~ 120k for the illustrated circuit. Threshold Voltage VHI: 3.8V VLO: 1.0V 180 RL VOUT GND ACTUATOR COLORS B White C Red D Amber F Green LED COLORS & SPECIFICATIONS LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25C. If the source voltage exceeds the rated voltage, a ballast resistor is required. R + IF Anode Single Element LED Color C Red 30mA 20mA 1.85V 5V 0.38mA /C IFM IF VF VRM IF D Amber 25mA 20mA 2.0V 5V 0.28mA /C -25 ~ +50C F Green 25mA 20mA 2.25V 5V 0.40mA /C E VF Cathode Forward Peak Current Continuous Forward Current Forward Voltage Reverse Peak Voltage Current Reduction Rate Above 25C Ambient Temperature Range - R= Where: R = E= VF = IF = E - VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com 03-07 Contactless Pushbuttons EXTERNAL PLUG OPTIONS C2 AT021 Assembled Connector Plug with Wire Leads Series FP01 No Code No Connector Plug Recommended connector plug for assembly: JST model number ZHR-6 Recommended crimp connector pins: JST model SZH-002T-P0.5 for 28-26AWG wire leads or SZH-003T-P0.5 for 32-28AWG wire leads. C3 AT022 Unassembled Connector Plug and Pins Connector plug body: JST model ZHR-6 Crimp connector pins: JST model SZH-002T-P0.5 Wire leads: 28-26AWG; 12-inch, unstripped; Blue for Pin 1 1 connector plug and 8 crimp connector pins only (no wire leads provided). Matching wire leads: 28-26AWG TYPICAL SWITCH DIMENSIONS (5.0) .197 NKK P/N This Side Pin 1 (1.1)R Typ .043 (25.1) .988 (19.6) Dia .772 (26.0) Dia 1.024 (1.5) .059 (5.3) .209 (21.4) .843 (2.3) .091 (22.8) Dia .898 (22.9) Dia .902 654321 FP0115CAC1FF Terminal Connector Detail Recommended Panel Thickness Range: .098" ~ .197" (2.5mm ~ 5.0mm) LEGENDS Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory or utilize the general information and basic specifications presented below. Suggested Printable Area for FP01 Cap NKK Switches * email: sales@nkkswitches.com * Phone (480) 991-0942 * Fax (480) 998-1435 * www.nkkswitches.com LM AL T ER Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended. (16.56) Dia .475 (19.6) Dia .772 (1.52) Typ .060 Shaded area is printable area. 03-07 |
Price & Availability of FP0115CAC1CC-C2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |