 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| SSO-AD-230-TO52-S1 Avalanche Photodiode Special characteristics: High gain at low bias voltage Fast rise time 230 m diameter active area low capacitance Parameters: active area dark current (M=100) 1) Total capacitance (M=100) Break-down voltage UBR (at ID=2A) Temperature coefficient of UBR Spectral responsivity (at 780 nm) Cut-off frequency (-3dB) Rise time Optimum gain Gain M "Excess Noise" factor (M=100) "Excess Noise" index (M=100) Noise current (M=100) N.E.P. (M=100, 880 nm) Operating temperature Storage temperature 50 - 60 min 200 1) Package (TO52 S1) : 0,042 mm 230 m max. 1,5 nA typ. 0,6 nA typ. 1,5 pF (90 ... 240) typ. 120 - 190 V typ. 0,4 %/C min. 0,40 A/W typ. 0,45 A/W typ. 2 GHz typ. 180 ps 2 typ. 2,2 typ. 0,2 typ. 0,5 pA/Hz -14 1/2 typ. 1 * 10 W/Hz -20 ... +70C -60 ... +100C 1/2 1) measurement conditions: Setup of photo current 10nA at M=1 and irradiation by a NIR-LED (880 nm, 80 nm bandwith). Rise of the photo current up to 1 A, (M=100) by internal multiplication due to an increasing bias voltage. SSO - AD - serie Spectral Responsivity at M=1 0,600 0,500 0,400 0,300 0,200 0,100 0,000 400 500 600 700 800 900 1000 1100 60 50 40 30 20 10 0 400 500 SSO - AD - serie Spectral Responsivity at M=100 Sabs (A/W) Sabs (A/W) 600 700 800 900 1000 1100 Wavelength (nm) Wavelength (nm) SSO - AD - serie quantum efficiency for M=1 1,00 0,90 0,80 0,70 0,50 0,40 0,30 0,20 0,10 0,00 400 480 560 640 720 800 880 960 1040 4 2 0 0 20 Ctot (pF) 14 12 10 8 6 SSO-AD 230 Ctot=f(UR) at f=100kHz 16 0,60 QE 40 UR (V) 60 80 100 wavelength (nm) SSO-AD 230 dark current = f(UR) 1000 100 10 M 1 0,1 0,01 0 20 40 60 80 UR (V) 100 120 140 160 10,00 100,00 10000,00 SSO-AD 230 gain = f(UR/UBR) at = 880 nm 1000,00 ID (pA) 1,00 0,0 0,2 0,4 UR/UBR 0,6 0,8 1,0 Maximum Ratings: * * * * Bias supply voltage max. electrical power dissipation max. optical peak value, once max. continous optical operation ( Pelectr. = Popt. * Sabs * M * UR ) 100 mW at 22C 200 mW for 1 s IPh (DC) 250 A 1 mA for signal 50 s "on" / 1 ms "out" Current limiting resistor Application hints: * * * * * * * Current limit is to be realized via protecting resistor or current limiting - IC inside the supply voltage. Use of low noise read-out - IC. For higher gain a regulation of bias voltage due to the temperature is to be realized. For very small signals stray light (noise source) is to be excluded by filters in order to improve the signal-noise relation. Avoid touching the window with fingers! Careful cleaning with Ethyl alcohol possible. Avoid use of pointed and scratching tools! min. 0,1 F, closest to APD APD Diode, protective circuit Read-out circuit or f.e. 50 Load resistance Handling precautions: * * * Soldering temperature min. Pin - length ESD - protection Storage 260C for max. 10 s. The device must be protected against solder flux vapour! 2mm Only small danger for the device. Standard precautionary measures are sufficient. Store devices in conductive foam. 2000/05 * |
Price & Availability of SSO-AD-230-TO52-S1
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |