View NSPLR70ASS_4573391.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

No. STSE-CW5169B
SPECIFICATIONS FOR NICHIA WARM WHITE LED
MODEL : NSPLR70ASS
NICHIA CORPORATION
-0-
Nichia STSE-CW5169B
1.SPECIFICATIONS
(1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Reverse Voltage Power Dissipation Operating Temperature Storage Temperature Soldering Temperature Symbol IF IFP VR PD Topr Tstg Tsld Absolute Maximum Rating 35 100 5 147 -30 ~ + 85 -40 ~ +100 265C for 5sec. (Ta=25C) Unit mA mA V mW C C
IFP Conditions : Pulse Width < 10msec. and Duty < 1/10 = =
(2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Reverse Current IR Luminous Flux V x Chromaticity Coordinate y Please refer to CIE 1931 chromaticity diagram.
Condition IF=30[mA] VR= 5[V] IF=30[mA] IF=30[mA] IF=30[mA]
Typ. (3.8) (4.0) 0.41 0.39
(Ta=25C) Max. Unit 4.2 V 50 A lm -
(3) Ranking Item Luminous Flux Rank Rc Rank Rb Rank Ra Symbol V V V Condition IF=30[mA] IF=30[mA] IF=30[mA] Min. 4.8 3.4 2.4
(Ta=25C) Max. Unit 6.8 lm 4.8 lm 3.4 lm
Luminous Flux Measurement allowance is 10%.
Color Ranks x y x y x y 0.3575 0.3612 0.3545 0.3408 0.3897 0.3823 0.3610 0.3850 0.3575 0.3612 0.3988 0.4116
(IF=30mA,Ta=25C) Rank d1 0.3780 0.3988 0.3970 0.4116 Rank d2 0.3720 0.3897 0.3714 0.3823 Rank e1 0.4162 0.4390 0.4200 0.4310 0.3897 0.3823 0.3822 0.3580 0.4255 0.4000 0.3720 0.3714 0.3667 0.3484 0.4053 0.3907
-1-
Nichia STSE-CW5169B Rank e2 0.4053 0.4255 0.3907 0.4000 Rank f1 0.4680 0.4970 0.4385 0.4466 Rank f2 0.4519 0.4770 0.4086 0.4137
x y x y x y
0.3822 0.3580 0.4255 0.4000 0.4129 0.3725
0.3897 0.3823 0.4390 0.4310 0.4255 0.4000
0.4129 0.3725 0.4770 0.4137 0.4588 0.3838
0.3954 0.3642 0.4519 0.4086 0.4355 0.3785
Color Coordinates Measurement allowance is 0.01.
2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS
Please refer to figure's page.
3.OUTLINE DIMENSIONS AND MATERIALS
Please refer to figure's page. Material as follows ; Resin(Mold) : Leadframe : Epoxy Resin (over Silicone Resin + Phosphor) Ag plating Copper Alloy
4.PACKAGING
* The LEDs are packed in cardboard boxes after packaging in stick. Please refer to figure's page. The label on the packing unit shows ; Part Number, Lot Number, Ranking, Quantity * In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. * The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. * The boxes are not water resistant and therefore must be kept away from water and moisture. * When the LEDs are transported, we recommend that you use the same packing method as Nichia.
5.LOT NUMBER
The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Color Coordinates - Ranking by Luminous Flux
B for Nov. )
-2-
Nichia STSE-CW5169B
6.RELIABILITY
(1) TEST ITEMS AND RESULTS
Test Item Resistance to Soldering Heat Solderability Thermal Shock Temperature Cycle Moisture Resistance Cyclic Terminal Strength (bending test) Terminal Strength (pull test) High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Condition 1 Steady State Operating Life Condition 2 Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Standard Test Method JEITA ED-4701 300 302 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 400 401 JEITA ED-4701 400 401 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260 5C, 5sec. 1.6mm from the base of the stopper (Pre treatment 30C,70%,168hrs.) Tsld=235 5C, (using flux) 0C ~ 100C 15sec. 15sec. -40C ~ 25C ~ 100C ~ 25C 30min. 5min. 30min. 5min. 25C ~ 65C ~ -10C 90%RH 24hrs./1cycle Load 5N (0.5kgf) 0 ~ 90 ~ 0 bend 2 times Load 10N (1kgf) 10 1 sec. Ta=100C Ta=60C, RH=90% Ta=-40C Ta=25C, IF=35mA Ta=35C, IF=30mA 60C, RH=90%, IF=20mA Ta=-30C, IF=30mA 5sec. Note 1 time Number of Damaged 0/50
1 time over 95% 100 cycles 100 cycles 10 cycles No noticeable damage No noticeable damage 1000hrs. 1000hrs. 1000hrs. 1000hrs. 1000hrs. 500hrs. 1000hrs.
0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50
(2) CRITERIA FOR JUDGING DAMAGE Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage VF IF=30mA U.S.L.*) 1.1 Reverse Current IR VR=5V U.S.L.*) 2.0 Luminous Flux IF=30mA L.S.L.**) 0.7 V *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level
-3-
Nichia STSE-CW5169B
7.CAUTIONS
The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current. Care should be taken after due consideration when using LEDs. (1) Storage * Storage Conditions Before opening the package : The LEDs should be kept at 30C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. * If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 85C * Nichia LED leadframes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the LEDs be used as soon as possible. * Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. (2) Static Electricity * Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. * All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. * When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). * Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA)
-4-
Nichia STSE-CW5169B (3) Soldering Conditions * Nichia LEDs uses a copper alloy lead frame which provides a high thermal conductivity. Thermal stress such as soldering heat may reduce the reliability of the product; particular caution should be used to avoid damage prior to and during soldering. The recommended soldering conditions are listed in the following table. * Solder the LED no closer than 1.6mm from the base of the stopper. * The mechanical stress by clinching will cause degradation of the reliability on the LEDs. It is important to minimize the mechanical stress on the LEDs. It should be confirmed beforehand that it will not cause any problem when using it. * Recommended soldering conditions
Pre-Heat Pre-Heat Time Solder Bath Temperature Dipping Time Dipping Position Dip Soldering 120C Max. 60 seconds Max. 260C Max. 5 seconds Max. No lower than 1.6 mm from the base of the stopper. Hand Soldering 350C Max. Temperature 3 seconds Max. Soldering Time No closer than 1.6 mm from the Position base of the stopper.
* Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest possible temperature is desirable for the LEDs. * A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. * Dip soldering should not be done more than one time. * Hand soldering should not be done more than one time. * Do not apply any stress to the lead particularly when heated. * The LEDs must not be repositioned after soldering. * After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. * Direct soldering onto a PC board should be avoided. Mechanical stress to the resin may be caused from warping of the PC board or from the clinching and cutting of the leadframes. When it is absolutely necessary, the LEDs may be mounted in this fashion but the User will assume responsibility for any problems. Direct soldering should only be done after testing has confirmed that no damage, such as wire bond failure or resin deterioration, will occur. Nichia's LEDs should not be soldered directly to double sided PC boards because the heat will deteriorate the epoxy resin. * When it is necessary to clamp the LEDs to prevent soldering failure, it is important to minimize the mechanical stress on the LEDs. * Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs. (4) Heat Generation * Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. * The operating current should be decided after considering the ambient maximum temperature of LEDs.
-5-
Nichia STSE-CW5169B (5) Cleaning * It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. * Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (6) Safety Guideline for Human Eyes * In 1993, the International Electric Committee (IEC) issued a standard concerning laser product safety (IEC 825-1). Since then, this standard has been applied for diffused light sources (LEDs) as well as lasers. In 1998 IEC 60825-1 Edition 1.1 evaluated the magnitude of the light source. In 2001 IEC 60825-1 Amendment 2 converted the laser class into 7 classes for end products. Components are excluded from this system. Products which contain visible LEDs are now classified as class 1. Products containing UV LEDs are class 1M. Products containing LEDs can be classified as class 2 in cases where viewing angles are narrow, optical manipulation intensifies the light, and/or the energy emitted is high. For these systems it is recommended to avoid long term exposure. It is also recommended to follow the IEC regulations regarding safety and labeling of products. (7) Others * NSPLR70AS complies with RoHS Directive. * Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LEDs with matrix drive. * Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. * The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). * User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. * The formal specifications must be exchanged and signed by both parties before large volume purchase begins. * The appearance and specifications of the product may be modified for improvement without notice.
-6-
Nichia STSE-CW5169B
ICI Chromaticity Diagram
0.9 520 530 0.8 510 0.7 550 540
560 0.6 570 500 0.5 e1 0.4 d1 600 d2 0.3 490 e2 f2 610 620 630 f1 580 590
y
0.2
0.1
480 470 460 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
0
x
Color Coordinates Measurement allowance is 0.01.
-7-
Forward Voltage vs. Forward Current
Forward Current IFP (mA) 100 50 20 10 5 Ta=25C Relative Luminous Flux (a.u.) 200
Forward Current vs. Relative Luminous Flux
3.0 2.5 2.0 1.5 1.0 0.5 0 0 20 40 60 80 100 120 Forward Current IFP (mA) Ta=25C Allowable Forward Current IFP (mA)
Duty Ratio vs. Allowable Forward Current
200 Ta=25C 100 50 30 20 10 1
1 2.5
3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V)
5 10 20 50 100 Duty Ratio (%)
Ambient Temperature vs. Forward Voltage
IFP=30mA Relative Luminous Flux (a.u.) 5.4 Forward Voltage VF (V) 5.0 4.6 4.2 3.8 3.4 3.0 2.6 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C)
Ambient Temperature vs. Relative Luminous Flux
Allowable Forward Current IF (mA) 2.0 IFP=30mA 1.0
Ambient Temperature vs. Allowable Forward Current
50 40 30 20 10 9 0 0 20 40 60 80 100 Ambient Temperature Ta (C)
-8-
0.5
0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C)
Nichia STSE-CW5169B
Model
NSPLR70AS
NICHIA CORPORATION
Title No.
CHARACTERISTICS
051104546931
Forward Current vs. Chromaticity Coordinate
Relative Emission Intensity (a.u.)
Spectrum
1.2 1.0 0.8 0.6 0.4 0.2 0 400 500 600 700 Wavelength (nm) 800 Ta=25C IF=30mA
0.41 Ta=25C 0.40 0.39 0.38 0.37 0.39
100mA 50mA 30mA 5mA 1mA
y
x Ambient Temperature vs. Chromaticity Coordinate
IFP=30mA
0.40
0.41
0.42
0.43
Directivity
1.0
Relative Illuminance (a.u.)
0.41
0 Ta=25C IFP=30mA
10 20
30 40 50
y
-9-
0.40 0.39
50C
-30C 0C 25C 85C
0.5
60 70 80
0.38
0.37 0.39
0.40
0.41
x
0.42
0.43
0 90
60 30 Radiation Angle
0
0.5
90 1.0
Nichia STSE-CW5169B
Model
NSPLR70AS
NICHIA CORPORATION
Title No.
CHARACTERISTICS
051104546941
Internal Circuit
3
A
2
A
3
7.62 0.5 3
2
7.5 0.5 4.4 0.5
7.62 0.5
4
R 0.69
1
(C 1.25) 1 Pin Mark
(5) 1.1
1.55
4
1
0.76 0.1
K
K
2.5 0.5
1.4MAX.
0.4 0.1
0.4 0.5
5.08 0.3
ITEM RESIN LEAD FRAME
MATERIALS Epoxy Resin (over Silicone Resin + Phosphor) Ag Plating Copper Alloy
Model
0.4
5.08
Stopper
-10-
Nichia STSE-CW5169B
Remark: Please note that the bare copper alloy showing at the cut end of the lead frame may be corroded under certain conditions. LEDs have some sharp edges and points, particularly lead frames. Please handle with care so as to avoid injuries.
NSPLR70AS
Unit mm 5/1 Scale Allow 0.2
NICHIA CORPORATION
Title No.
OUTLINE DIMENSIONS
051104546951
Cross Sectional image of stick
5.4
11.8
5.85
9
1 t = 0.6 0.1mm 2 Warp : 1mm Max.
3 9.6
-11-
Whole image of stick
485 1
Cap
NICHIA >PC< CAUTION TO ELECTROSTATIC DAMAGE
A
K
60pcs / stick
Nichia STSE-CW5169B
Model
NSPxR70xSS
Unit mm Scale Allow 0.2
NICHIA CORPORATION
Title No.
STICK DIMENSIONS
050725436072
Nichia STSE-CW5169B The stick and moisture absorbent material are put in the moisture proof foil bag and then heat sealed.
Moisture absorbent material Moisture proof foil bag
Stick
Label
NICHIA
XXXX LED
TYPE LOT QTY NSPxR70xSS xxxxxxPCS
Seel
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Label
NICHIA
XXXX LED
TYPE RANK QTY NSPxR70xSS PCS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Empty space in the box is filled with cushion material. Packing unit
Moisture proof foil bag Cardboard box Cardboard box M Cardboard box 1/2L Cardboard box L Stick/bag 10 stick Max. Dimensions (mm) 590 277 120 4t 613 298 268 7t 613 298 518 7t Quantity/bag (pcs) 600 MAX. Stick/box 100 stick MAX. 200 stick MAX. 400 stick MAX. Quantity/box (pcs) 6,000 MAX. 12,000 MAX. 24,000 MAX.
Model
NSPxR70xSS
NICHIA CORPORATION
Title No.
PACKING
050725436082
-12-

▲Up To Search▲

Price & Availability of NSPLR70ASS

	To Download NSPLR70ASS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .