 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com SIPAT Co., Ltd. 1. Package Dimension ( S34 ) Unit: mm Pin No. Function 1 Input Ground 2 Input 5 Output 6 Output Ground 4,8 Case-Ground 3,7 to be Grounded 2. Marking DF01D H5 (1) Ink Marking or Laser Marking (2) DF: Manufacture's logo (3) 01D: Model code (4) : Pin 1 Identifier (5) H5: Date code H Month code 5 Last figure of year Month Month code 1 A 2 B 3 C 4 D 5 E 6 F 7 G 8 H 9 I 10 J 11 K 12 L e.g.: " H5 " means August of 2005 SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 1/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com SIPAT Co., Ltd. 3. Performance 3.1 Application RF Low-loss SAW Filter for Remote Controller Receivers. Center frequency(fo): 433.92 MHz 3.2 Maximum Rating DC Voltage Between Terminals VDC Operation Temperature Range Storage Temperature Range CW RF Power Dissipation 3.3 Electronic Characteristics Item Center Frequency (fo) Insertion Loss 433.76MHz ~ 434.08MHz Pass Band 433.76 ~ 434.08 MHz 433.74 ~ 434.10 MHz 3dB Bandwidth Relative Attenuation (Relative to ILmin) 10.00 ~ 414.00MHz 414.00 ~ 423.50MHz 423.50 ~ 431.72MHz 431.72 ~ 432.12MHz 432.12 ~ 433.10MHz 434.92 ~ 442.00MHz 442.00 ~ 500.00MHz 500.00 ~ 700.00MHz 700.00 ~ 1000.00MHz Impedance at 433.92MHz Input: Zin = Rin // Cin Output: Zout = Rout//Cout Turnover Temperature Turnover Frequency Temperature Coefficient Units MHz dB dB dB KHz dB dB dB dB dB dB dB dB dB //pF //pF MHz Ppm/2 Minimum ---- ---- ---- ---- 600 42.0 39.0 29.0 26.0 17.0 14.0 35.0 40.0 48.0 ---- ---- 10 ---- ---- Typical 433.92 3.0 1.1 1.4 750 45.0 41.0 34.0 35.0 21.0 15.0 37.0 42.0 52.0 150//4.7 150//4.7 25 433.92 0.033 Maximum ---- 5.0 2.0 3.0 850 ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- ---- 40 ---- ---- 10V -40 to +85 -40 to +85 10dBm SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 2/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com 3.4 Frequency Characteristics SIPAT Co., Ltd. SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 3/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com 3.5 Test Circuit SIPAT Co., Ltd. C=5pF; L=32nH 4. Reliability 4.1 Mechanical Shock: The components shall remain within the electrical specifications after three one-half sine shock pulses(3000g's for 0.3ms) in each direction(for six total) along each of the three mutually perpendicular axes for a total of 18 shocks. 4.2 Vibration Fatigue: The components shall remain within the electrical specifications after loaded vibration at 20~55Hz, amplitude 1.5mm, X,Y,Z, direction, for 2 hours. 4.3 Leak Test 4.3.1 Gross Leak Test: Submerge samples into at +85 water for at least 1 minute. Carefully observe the samples. No bubbles should be seen. 4.3.2 Fine Leak Test: Expose samples for testing to 60 PSIG Helium gas for 2 hours. Then transfer the same samples to another chamber and draw a vacuum. Measure the leak rate. Failure is defined if the leak rate exceeds 5x10-8 atm cc/sec Helium. 4.4 High Temperature Storage: The components shall remain within the electrical specifications after being kept at the 852for 960 hours, then kept at room temperature for 2 hours. 4.5 Low Temperature Storage: The components shall remain within the electrical specifications after being kept at the -402for 960 hours, then kept at room temperature for 2 hours. 4.6 Temperature Cycle: The components shall remain within the electrical specification after 32 cycles of high and low temperature testing (one cycle: 80 for 30 minutes 25 for 20 seconds -40 for 30 minutes) than kept at room temperature for 2 hours. 4.7 Humidity Test: The components shall remain within the electrical specifications after being kept at the condition of ambient temperature 70, and 90~95% RH for 240 hours, then kept at room temperature and normal humidity for 4 hours. 4.8 Solder-heat Resistance: The components shall remain within the electrical specifications after dipped in the solder at 2605 for 10 to 11 seconds, then kept at room temperature for 10 minutes. SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 4/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com SIPAT Co., Ltd. 4.9 Solderability: Solderability of terminal shall be kept at more than 80% after dipped in the solder flux at 2305 for 51 seconds. 4.10 Storage: The components shall meet the electrical and mechanical specifications after 5 years storage, if stored within the temperature range of -40~+85 and in the humidity of 20 to 60% r.h. 5. Remarks 5.1 Static voltage Static voltage between signal load & ground may cause deterioration & destruction of the component. Please avoid static voltage. 5.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning. 5.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. 6. Packing 6.1 Dimensions (1) Carrier Tape: Figure 1 (2) Reel: Figure 2 (3) The product shall be packed properly not to be damaged during transportation and storage. 6.2 Reeling Quantity 1,000 pcs/reel 6.3 Taping Structure (1) The tape shall be wound around the reel in the direction shown below. TOP COVER TAPE CARRIER TAPE SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 5/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com (2)Lable Device Name Type Quantity Lot No. (3) Leader part and vacant position specifications. SIPAT Co., Ltd. Vacant Components Contained Vacant Leader Part TAPE RUNNING DIRECTION 7.Tape Specifications 7.1Tensile Strength of Carrier Tape: 4.4N/mm width 7.2Top Cover Tape Adhesion (See the below figure) (1) pull off angle: 0~15 (2) speed: 300mm/min. (3) force: 20~70g TOP COVER TAPE Direction of pull off CARRIER TAPE SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 6/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com [Figure 1] Carrier Tape Dimensions SIPAT Co., Ltd. Tape Running Direction [Unit: mm] W 12.0 0.3 F 5.5 0.1 E 1.75 0.1 P0 4.0 0.2 P1 4.0 0.1 P2 2.0 0.2 D0 1.5 0.1 D1 1.5 0.25 t1 0.31 max. t2 1.95 max. A 3.3 max. B 3.3 max. [Figure 2] Reel Dimensions [Unit: mm] SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 7/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com China Electronics Technology Group Corporation No.26 Research Institute 433.92MHz RF SAW Filter 0.6MHz Bandwidth Part Number: SP43302 www.sipatsaw.com [Figure 3] Part Direction SIPAT Co., Ltd. Tape Running Direction SIPAT Co., Ltd. ( CETC No. 26 Research Institute ) Nanping Huayuan Road No. 14 Chongqing, China, 400060 Part Number Rev. Date Rev. SP43302 2006-7-19 1.0 Page 8/8 Phone: +86-23-62808818 Fax: +86-23-62805284 www.sipatsaw.com / sawmkt@sipat.com |
Price & Availability of SP43302
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |