 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 S P E C I F I C A T I O N S Dielectris & Values Terminations Voltage Packing Capacitance Tolerance Operating Temperature Range NPO X7R Y5V Z5U consult product pages of catalog for cap ranges and voltage rating Tin / Nickel 16, 25, 50, 63 VDC tape and reel (0402, 0603, 0805, 1206, 1210, 1812, 2220) 0.5pF ~ 10uF 0.1pF ~ +80-20% NPO: -55 ~ +125 X7R: -55 ~ +125 Y5V: -30 ~ +85 NPO : The capacitor of this kind dielectric material is considered as Classcapacitor, including general capacitor and high frequency NPO capacitorThe electrical properties of NPO capacitor are the most stable one and have little change with temperature, voltage and time. They are suited for applications where low-losses and high-stability are required, such as filters, oscillators, and timing circuits. X7RX5R: X7RX5R material is a kind of material has high dielectric constant. The capacitor made of this kind material is considered as Class capacitor whose capacitance is higher than that of class . These capacitors are classified as having a semi-stable temperature characteristic and used over a wide temperature range, such in these kinds of circuits, DC-blocking, decoupling, bypassing, frequency discriminating etc. Y5V: The capacitor made of this kind of material is the highest dielectric constant of all ceramic capacitors. They are used over a moderate temperature range in application where high capacitance is required because of its unstable temperature coefficient, but where moderate losses and capacitance changes can be tolerated. Its capacitance and dissipation factors are sensible to measuring conditions, such as temperature and voltage, etc Types of Capacitor and Dielectric Material Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 Specification and Test Condition 1. Appearance Dielectrics NPO/X7R/X5R/Y5V 2. Dimensions Dielectrics NPO/X7R/X5R/Y5V 3. Capacitance Dielectrics NPO Specification Within the specified tolerance B:0.1pF;C:0.25pF;D:0.5pF;J: 5% Within the specified tolerance J: 5%K: 10% M: 20% Within the specified tolerance M: 20%; Z: -20%, +80% Testing Condition 1.00.2Vrms, 1MHz10% (C>1000 pF, 1.00.2Vrms, 1KHz10%) 25 1.00.2Vrms, 1KHz10% Cp10uF,0.50.1Vrms,12024Hz at 25,48hrs after annealing 1.00.2Vrms, 1KHz10% Cp10uF,0.50.1Vrms,12024Hz at 25, 48hrs after annealing Specification Within the specified dimensions Testing Condition Using calipers on micrometer Specification No defects or abnormalities Testing Condition Visual inspection. X7R/X5R Y5V 4. Dissipation Factor Dielectrics NPO Specification Cp<30pF, Q400+20Cp; Cp30pF, Q1000 UR25V, DF 2.5% UR =16V, DF 3.5% UR 10V, DF 5.0% UR25V, DF 7.0% (C<1.0F) DF 9.0% (C1.0F) UR =16V, DF 9.0% UR 10V, DF 12.5% Testing Condition 1.00.2Vrms,1MHz10% ,25 (Cp>1000pF,1.00.2Vrms,1KHz10%) 1.00.2Vrms, 1KHz10%, (Cp10uF,0.50.1Vrms,12024Hz) at 25,48hrs after annealing 1.00.2Vrms, 1KHz10%, (Cp10uF,0.50.1Vrms,12024Hz) at 25,48hrs after annealing X7R/X5R Y5V Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 5. Insulation Resistance Dielectrics NPO/X7R/ X5R/Y5V 6. Dielectric Strength Dielectrics Specification Testing Condition No failure shall be observed when 300% (NPO);250%(X7R/ X5R/Y5V)of the rated voltage is applied between the terminations fo 1 to 5 seconds, provided the charge /discharge current is less than 500mA 7. Temperature Coefficient of Capacitance Dielectrics Specification Temperature coefficient within 30ppm/ Cp drift within 0.2% or 0.05pF Specification More than 10 G or 500*F, whichever is smaller. Testing Condition Rated voltage for 605sec, at 25 NPO /X7R/X5R/Y5V No defects or abnormalities. Testing Condition Measure capacitance under follow table list temperature: STEP NPO, X7R X5R Y5V 1 2 3 4 5 25 2 -553 25 2 1253 25 2 25 2 -553 25 2 853 25 2 25 2 -303 25 2 853 25 2 NPO X7R/X5R Capacitance change within 15% Y5V Capacitance change within +22%, -82% 1) NPO The capacitance drift is calculated by dividing the differences between the maximum and minimum measured values in the step 1,3 and 5. The temperature coefficient is determined using the Capacitance measured in step 3 as a reference. 2) X7R ,X5R and Y5V The ranges of capacitance change compared within the above 25 value over the temperature ranges shall be within the specified ranges. Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 8. Adhesion Dielectrics Specification Testing Condition The pressurizing force shall be 10N (=1000g*f) and the duration of application shall be 101sec. NPO X7R/X5R Y5V No removal of the terminations or other defect shall occur. hooked jig boar d r= 5 0. hi p cr oss- sect i on 9. Solderability of Termination Dielectrics NPO X7R/X5R Y5V 10. Resistance to leaching Dielectrics NPO X7R/X5R Y5V Specification 95% min. coverage of both terminal electrodes and less than 5% have pin holes or rough spots. No remarkable visual damage. Testing Condition Solder temperature: 2705 Dipping time: 101 seconds. Completely soak both terminal electrodes in solder Specification 95% min. coverage of both terminal electrodes and less than 5% have pin holes or rough spots. Testing Condition Solder temperature: 2305 Dipping time: 21 seconds. Completely soak both terminal electrodes in solder Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 11. Bending Dielectrics NPO Specification No remarkable visual damage Cp change 5% or 0.5 pF No remarkable visual damage Cp change 12.5% Testing Condition Solder the capacitor on testing substrate and put it on testing stand. The middle part of substrate shall successively be pressurized by pressuring rod at a rated of about 1.0mm/sec. Until the deflection become means of the 1.0mm. X7R/X5R Y5V No remarkable visual damage Cp change 30% 12. Resistance to Soldering Heat Dielectrics NPO Testing Condition Soldering temperature: 2705 No remarkable visual damage Preheating: 120~150 60sec. Cp change within 2.5% or 0.25pF, Dipping time: 101 seconds. whichever is larger. Measurement to be made after being kept at DF meets initial standard value. room temperature for 242 (C0G) or IR meets initial standard value. 484(X7R ,X5R, Y5V) hours. Recov ery for the following period under No remarkable visual damage the standard condition after test. Cp change within 5% DF meets initial standard value. *Initial measurement for high dielectric constant type IR meets initial standard value. Perform a heat treatment at 140~150 for No remarkable visual damage 1hr and let sit for 484hrs at room Cp change within 20% temperature. Perform the initial DF meets initial standard value. measurement. IR meets initial standard value. Specification X7R/X5R Y5V Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 13. Temperature Cycle Dielectrics Specification Testing Condition To perform 5 cycles of the stated environment: Step 1 2 3 4 Temperature Min. operating Temp.+0/-3 25 Max. operating Temp.+0/-3 25 Time 30min 2~3 min 30 min 2~3 min NPO No remarkable visual damage Cp change within 2.5% or 0.25pF, whichever is larger. X7R/X5R No remarkable visual damage Cp change within 7.5% Measurement to be made after being kept at room temperature for 242hrs (C0G) or 484hrs (X7R, X5R, Y5V) at room temperature, then measure. *Initial measurement for high dielectric constant type Perform a heat treatment at 140~150 for 1hr and let sit for 484hrs at room temperature. Perform the initial measurement. Testing Condition 14. Moisture Resistance ,steady state Dielectrics Specification No remarkable visual damage Cp change within 5% or 0.5pF, whichever is larger. Cp<10pF, Q200+10Cp; 10Cp<30pF, Q275+2.5Cp Cp30pF, Q350 R*C1000M or 50*F, whichever is smaller Cp change within 12.5% DF:Not more than 2 times of initial value R*C1000M or 50*F, whichever is smaller No remarkable visual damage Cp change within 30% DF:Not more than 1.5 times of initial value R*C1000M or 50*F, whichever is smaller Website: www.suntan.com.hk NPO Test temperature: 402 Humidity: 90~95% RH Testing time: 500 12hrs Measurement to be made after being kept at room temperature for 242hrs (C0G) or 484hrs (X7R, X5R, Y5V) *Initial measurement for high dielectric constant type Perform a heat treatment at 140~150 for 1hr and let sit for 484hrs at room temperature. Perform the initial measurement. X7R/X5R Y5V Suntan(R) Technology Company Limited Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 15. Damp heat with load Dielectrics Specification No remarkable visual damage Cp change7.5% or 0.75pF, whichever is larger. Cp<30pF, Q100+10/3*Cp Cp30pF, Q200 R*C500M or 25*F, whichever is smaller No remarkable visual damage Cp change12.5% DF:Not more than 2 times of initial value R*C500M or 25*F, whichever is smaller No remarkable visual damage Cp change30% DF:Not more than 1.5 times of initial value R*C500M or 25*F , whichever is smaller Specification No remarkable visual damage Cp change3% or 0.3pF, whichever is larger. Q350 (Cp30 PF) Q275+(2.5* Cp) (10 pFCp<30 PF) Q200+10*Cp (Cp<10 PF) R*C1000M or 50*F, whichever is smaller No remarkable visual damage Cp change12.5% DF:Not more than 2 times of initial value R*C1000M or 50*F, whichever is smaller No remarkable visual damage Cp change30% DF:Not more than 1.5 times of initial value R*C1000M or 50*F, whichever is smaller Testing Condition Test temperature: 402 Humidity: 90~95% RH Voltage: 100% of the rated voltage Testing time: 500 12hrs Measurement to be made after being kept at room temperature for 242hrs (C0G) or 484hrs (X7R, X5R, Y5V) *Apply the rated DC voltage for 1 hour at 402. Remove and let sit for 484hrs at room temperature. Perform the initial measurement. NPO X7R/X5R Y5V 16. Life Test Dielectrics Testing Condition Test temperature: Max. Operating Temp. 3 Voltage: 200% of the rated voltage Testing time: 1000 hrs Measurement to be made after being kept at room temperature for 242hrs (C0G) or 484hrs (X7R, X5R,Y5V) *Initial measurement for high dielectric constant type Apply 200% of the rated DC voltage for one hour at the maximum operating temperature 3. Remove and let sit for 484hrs at room temperature. Perform the initial measurement NPO X7R/X5R Y5V Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 Packing 1. Tape Packing Paper Tape: Standard taping (8mm paper width) suitable to 0603,0805,4Kpcs/reel To 0402, 10Kpcs/reel. Plastic Tape: Suitable 08051206 sizes, for chip thickness over 0.95 mm, 4Kpcs/reel or 3Kpcs/reel are available. 2. Dimensions of Packing Paper Type 0402 0603 0805 1206 A 0.650.10 1.050.10 1.550.15 1.950.15 B 1.150.10 1.850.10 2.30.15 3.50.15 C 2.00.05 4.00.10 4.00.10 4.00.10 D 2.00.05 2.00.10 2.00.10 2.00.10 T 0.8max 1.1max 1.1max 1.1max 3. Dimensions of Embossed Packing A1.450.20 A1.950.20 B2.250.20 0805 B3.500.20 1206 Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 4. Dimensions of Reel: 180mmReel 5. Taping Figure Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 MULTILAYER CERAMIC CHIP CAPACITOR - SMD Suntan(R) TS18 6. Taping Method Tapes for capacitors are wound clockwise. The sprocket holes are to the right as the tape is pulled toward the user. The top tape and base tape are not attached at the end of the tape for a minimum of 5 pitches. Part of the leader and part of the empty tape shall be attached to the end of the tape as follows. Missing capacitors number within 0.1% of the number per reel or 1pc, whichever is greater, and are not continuous. The top tape and bottom tape shall not protrude beyond the edges of the tape and shall not cover sprocket holes. Cumulative tolerance of sprocket holes, 10 pitches: 0.3mm. Peeling off force: 0.1 to 0.6N in the direction shown down. Note: Specification are subject to change without notice. For more detail and update, please visit our website. Suntan(R) Technology Company Limited Website: www.suntan.com.hk Email: info@suntan.com.hk Tel: (852) 8202 8782 Fax: (852) 8208 6246 |
Price & Availability of TS18
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |