View M37480E8-XXXFP_4870312.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

To all our customers
Regarding the change of names mentioned in the document, such as Mitsubishi Electric and Mitsubishi XX, to Renesas Technology Corp.
The semiconductor operations of Hitachi and Mitsubishi Electric were transferred to Renesas Technology Corporation on April 1st 2003. These operations include microcomputer, logic, analog and discrete devices, and memory chips other than DRAMs (flash memory, SRAMs etc.) Accordingly, although Mitsubishi Electric, Mitsubishi Electric Corporation, Mitsubishi Semiconductors, and other Mitsubishi brand names are mentioned in the document, these names have in fact all been changed to Renesas Technology Corp. Thank you for your understanding. Except for our corporate trademark, logo and corporate statement, no changes whatsoever have been made to the contents of the document, and these changes do not constitute any alteration to the contents of the document itself. Note : Mitsubishi Electric will continue the business operations of high frequency & optical devices and power devices.
Renesas Technology Corp. Customer Support Dept. April 1, 2003
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
DESCRIPTION
The 7480/7481 group is the single-chip microcomputer adopting the silicon gate CMOS process. In addition to its simple instruction set, the ROM, RAM, and I/O addresses are placed in the same memory space. Having built-in serial I/O, A-D converter, and watchdog timer, this single-chip microcomputer is useful for control of automobiles, office automation equipment and home electric appliances. The 7480/7481 group includes multiple types which differ in the memory type, size, and package.
PIN CONFIGURATION
FEATURES
qNumber of basic machine language instructions ..................... 71 qMinimum instruction execution time ................................... 0.5 s (at 8 MHz clock input oscillation frequency) qMemory size ROM ........................................... 4 K to 16 K bytes RAM ............................................ 128 to 448 bytes qProgrammable I/O ports .................................... 18 (7480 group) (P0, P1, P4, P5) 24 (7481 group) qInput ports ............................................................ 8 (7480 group) (P2, P3) 12 (7481 group) qBuilt-in programmable pull-up transistors (P0, P1) qBuilt-in clamp diodes ............................................ 2 (7480 group) (P4, P5) 8 (7481 group) qInterrupt ................................................... 14 sources, 13 vectors qTimer X, Y ..................................................................... 16-bit ! 2 qTimer 1, 2 ....................................................................... 8-bit ! 2 qSerial I/O ....................... 8-bit x 1 (UART or clock-synchronized) qA-D converter ............................ 8-bit x 4 channels (7480 group) 8-bit x 8 channels (7481 group) qBuilt-in watchdog timer qPower source voltage ................................................ 2.7 to 4.5 V (at [2.2 VCC-2] MHz clock input oscillation frequency) 4.5 to 5.5 V (at 8 MHz clock input oscillation frequency) qPower dissipation .............................................................. 35 mW (at 8 MHz clock input oscillation frequency and 5 V power source voltage)
P17/SRDY P16/SCLK P15/TXD P14/RXD P13/T1 P12/T0 P11 P10 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
P07 P06 P05 P04 P03 P02 P01 P00 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1 P30/INT0 RESET VCC
Outline 32P4B
M37480MX-XXXSP M37480MXT-XXXSP M37480E8-XXXSP M37480E8T-XXXSP
APPLICATIONS
Automobiles, office automation equipment, home electric appliances, etc.
P17/SRDY P16/SCLK P15/TXD P14/RXD P13/T1 P12/T0 P11 P10 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
P07 P06 P05 P04 P03 P02 P01 P00 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1 P30/INT0 RESET VCC
Outline 32P2W-A
Fig. 1 Pin configuration (top view)
M37480MX-XXXFP M37480MXT-XXXFP M37480E8-XXXFP M37480E8T-XXXFP
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
P53 P17/SRDY P16/SCLK P15/TXD P14/RXD P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22
P52 P07 P06 P05 P04 P03 P02 P01 P00 P43 P42 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1 P30/INT0 RESET P51 P50 VCC
32
31
27
29
28
26
30
33
25
P04 P05 P06 P07 P52 VSS P53 P17/SRDY P16/SCLK P15/TXD P14/RXD
24
23
P03 P02 P01 P00 P43 P42 P41/CNTR1 P40/CNTR2 P33 P32 P31/INT1
34 35 36 37 38 39 40 41 42 43 44
10 11 1 2 3 4 5 6 7 8 9
22 21 20 19
P30/INT0 RESET P51 P50 VCC VSS AVSS XOUT XIN VREF P20/IN0
Outline 42P4B 42S1B-A
Fig. 2 Pin configuration (top view)
2
P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1
M37481MX-XXXSP M37481MXT-XXXSP M37481E8-XXXSP M37481E8T-XXXSP M37481E8SS
M37481MX-XXXFP M37481MXT-XXXFP M37481E8-XXXFP M37481E8T-XXXFP
18 17 16 15 14 13 12
Outline 44P6N-A
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7480/7481 GROUP PRODUCT LIST
Table 1. 7480/7481 group product list Product model name M37480M2T-XXXSP M37480M2T-XXXFP M37480M4-XXXSP M37480M4-XXXFP M37480M4T-XXXSP M37480M4T-XXXFP M37480M8-XXXSP M37480M8-XXXFP M37480M8T-XXXSP M37480M8T-XXXFP M37480E8SP M37480E8FP M37480E8-XXXSP M37480E8-XXXFP M37480E8T-XXXSP M37480E8T-XXXFP M37481M2T-XXXSP M37481M2T-XXXFP M37481M4-XXXSP M37481M4-XXXFP M37481M4T-XXXSP M37481M4T-XXXFP M37481M8-XXXSP M37481M8-XXXFP M37481M8T-XXXSP M37481M8T-XXXFP M37481E8SP M37481E8FP M37481E8-XXXSP M37481E8-XXXFP M37481E8T-XXXSP M37481E8T-XXXFP M37481E8SS *: Extended operating temperature range version 16384 448 24 I/O ports 12 input ports (including 8 analog input ports) 8192 256 4096 128 16384 448 8 input ports (including 4 analog input ports) 18 I/O ports 8192 256 ROM (bytes) 4096 RAM (bytes) 128 I/O port Package 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 32P4B 32P2W-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42P4B 44P6N-A 42S1B-A One time PROM version* Built-in EPROM version One time PROM version One time PROM version (shipped in blank) One time PROM version Mask ROM version* Mask ROM version Mask ROM version* Mask ROM version Remarks Mask ROM version*
One time PROM version*
Mask ROM version*
Mask ROM version
Mask ROM version*
Mask ROM version
Mask ROM version* One time PROM version (shipped in blank)
3
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
7480/7481 GROUP ROM/RAM DEVELOPMENT SCHEDULE
ROM size (bytes)
16K
M37481E8SS M37480M8T/E8T-XXXSP/FP M37481M8T/E8T-XXXSP/FP M37480M8/E8-XXXSP/FP M37481M8/E8-XXXSP/FP
12K
8K
M37480M4-XXXSP/FP M37480M4T-XXXSP/FP M37481M4-XXXSP/FP M37481M4T-XXXSP/FP
4K
M37480M2T-XXXSP/FP M37481M2T-XXXSP/FP : Being developed : Being planned
0
128
256
384
448
RAM size (bytes)
Note: Regarding the models being developed and planned, the development schedule may be reviewed. In case of the models being planned, the development of them may be stopped. Fig. 3 ROM/RAM development schedule
4
PRE
M37480M8/E8-XXXSP/FP, M37480M8T/E8T-XXXSP/FP FUNCTION BLOCK DIAGRAM
Reset input RESET VCC VSS
16 17 18
L
Clock Clock input output XOUT XIN
A IMIN
14
15
Fig. 4 Function block diagram (1)
Data bus (Note 2) (Note 1)
ge. ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
Clock generating circuit
RY
FUNCTIONAL BLOCK DIAGRAM
RAM 448 bytes Instruction decoder Timer 2 (8) Control signal INT0 Index register X (8) Index register Y (8) Stack pointer S (8) Timer X (16) INT1 Timer Y (16) Processor status register PS (8)
Program counter PCH (8) ROM 16384 bytes Timer 1 (8)
Program counter PCL (8)
Instruction register (8)
8-bit arithmetic and logical unit
Accumulator A (8)
A-D converter CNTR0 INT1 INT0
4
Serial I/O (8)
CNTR1
P4 (2) P3 (4)
P2 (4)
P1 (8)
P0 (8)
24 23 22 21 20 19
13
9 10 11 12
12345678
32 31 30 29 28 27 26 25
I/O port P4
VREF Input port P3 Reference voltage input
Input port P2
I/O port P1
I/O port P0
Notes 1: 8192 bytes for M37480M4-XXXSP/FP, M37480M4T-XXXSP/FP and 4096 bytes for M37480M2T-XXXSP/FP 2: 256 bytes for M37480M4-XXXSP/FP, M37480M4T-XXXSP/FP and 128 bytes for M37480M2T-XXXSP/FP
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
5
6
PRE
M37481M8/E8-XXXSP, M37481M8T/E8T-XXXSP, M37481E8SS FUNCTION BLOCK DIAGRAM
Reset input RESET VCC
22 21
L
Clock input XIN VSS
25
Clock output XOUT
A IMIN
19
20
Fig. 5 Function block diagram (2)
Data bus
(Note 2) (Note 1)
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
Clock generating circuit
RY
.
RAM 448 bytes Instruction decoder Timer 2 (8) Control signal INT0 Index register X (8) Index register Y (8) Stack pointer S (8) Timer X (16) INT1 Timer Y (16) Processor status register PS (8)
Program counter PCH (8) Program counter PCL (8) ROM 16384 bytes Timer 1 (8)
Instruction register (8)
8-bit arithmetic and logical unit
Accumulator A (8)
A-D converter CNTR0 INT1 INT0
8
Serial I/O (8)
CNTR1
P5 (4) P3 (4)
P4 (4)
P 2 (8)
P1 (8)
P0 (8)
1 42 24 23 29 28 27 26 18
33 32 31 30
10 11 12 13 14 15 16 17
23456789
41 40 39 38 37 36 35 34
I/O port P5
I/O port P4
VREF Input port P3 Reference voltage input
Input port P2
I/O port P1
I/O port P0
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Notes 1: 8192 bytes for M37481M4-XXXSP, M37481M4T-XXXSP and 4096 bytes for M37481M2T-XXXSP 2: 256 bytes for M37481M4-XXXSP, M37481M4T-XXXSP and 128 bytes for M37481M2T-XXXSP
PRE
M37481M8/E8-XXXFP, M37481M8T/E8T-XXXFP FUNCTION BLOCK DIAGRAM
Reset input RESET VCC
18 17 39 16
L
Clock Clock input output XOUT XIN VSS AVSS
21
A IMIN
14
15
Fig. 6 Function block diagram (3)
Data bus
(Note 2) (Note 1)
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
Clock generating circuit
RY
.
RAM 448 bytes Instruction decoder Timer 2 (8) Control signal INT0 Accumulator A (8) INT1 Timer Y (16) Processor status register PS (8) Timer X (16) Index register X (8) Stack pointer S (8) Index register Y (8)
Program counter PCH (8) Program counter PCL (8) ROM 16384 bytes Timer 1 (8)
Instruction register (8)
8-bit arithmetic and logical unit
A-D converter CNTR0 INT1 INT0
8
Serial I/O (8)
CNTR1
P5 (4)
P4 (4)
P3 (4)
P2 (8)
P1 (8)
P0 (8)
40 38 20 19 13 VREF
29 28 27 26 25 24 23 22
5 6 7 8 9 10 11 12
41 42 43 44 1 2 3 4
37 36 35 34 33 32 31 30
I/O port P5
I/O port P4
Input port P3 Reference voltage input
Input port P2
I/O port P1
I/O port P0
Notes 1: 8192 bytes for M37481M4-XXXFP, M37481M4T-XXXFP and 4096 bytes for M37481M2T-XXXFP 2: 256 bytes for M37481M4-XXXFP, M37481M4T-XXXFP and 128 bytes for M37481M2T-XXXFP
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
7
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONS OF 7480/7481 GROUP
Table 2. Functions of 7480/7481 group Functions Parameter M37480M4/M8/E8-XXXSP/FP M37480M2T/M4T/M8T/E8T-XXXSP/FP Number of basic instructions Instruction execution time Clock input oscillation frequency M8/E8 ROM Memory size RAM M4 M2 M8/E8 M4 M2 P0, P1 P2 I/O port P3 P4 P5 I/O characteristics Serial I/O Timers M8/E8 Subroutine nesting M4 M2 Interrupt A-D converter (successive comparison method) Clock generating circuit Watchdog timer Power source voltage Power dissipation Operating temperature range Device structure Package 8 bits ! 4 analog inputs (in common with P2) I/O Input Input I/O I/O 2 bits ! 1 ---------- 5V -5 to 10 mA (P0, P1: CMOS tri-states), 10 mA (P4, P5: N channel) 8 bits ! 1 16-bit timer x 2, 8-bit timer x 2 192 max. 96 max. 64 max. 5 external interrupts, 8 internal interrupts, 1 software interrupt 8 bits ! 8 analog inputs (in common with P2) 4 bits ! 1 4 bits ! 1 4 bits ! 1 4 bits ! 1 M37481M4/M8/E8-XXXSP/FP M37481M2T/M4T/M8T/E8T-XXXSP/FP
71 (740 family 69 basic instructions + 2 multiplication/division instructions) 0.5s (Minimum instructions, at 8 MHz clock input oscillation frequency) 8 MHz (max.) 16384 bytes 8192 bytes 4096 bytes 448 bytes 256 bytes 128 bytes 8 bits ! 2 8 bits ! 1
I/O withstand voltage Output current
Built-in circuit with feedback resistor (with external ceramic oscillator) Built-in circuit 2.7 to 4.5 V (at f(XIN) = (2.2VCC - 2) MHz) 4.5 to 5.5 V (at f(XIN)=8 MHz) 35 mW (standard, at 8 MHz clock input oscillation frequency) -20 to 85 C (-40 to 85 C for extended operating temperature range version) CMOS silicon gate 32-pin SDIP/32-pin SOP 42-pin SDIP/44-pin OFP
8
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PIN DESCRIPTION
Table 3. Pin description Pin VCC, VSS AVSS VREF
_____
Name Power source Analog power source input Reference voltage input Reset input Clock input Clock output
Input/ output
Functions Apply a voltage of 2.7 to 5.5 V to VCC and 0 V to VSS. Ground level input pin for A-D converter. Apply the same voltage as Vss. (This pin is for 44P6N-A package only.)
Input Input Input Output
Reference voltage input pin for A-D converter. (When the A-D converter is not used, connect it to VCC.) Reset input pin active "L". These are I/O pins for the internal clock generating circuit of the main clock. To control the generating frequency, an external ceramic is connected between the XIN and XOUT pins. If an external clock is used, the clock source should be connected to the XIN pin, and the XOUT pin should be left open. The feedback resistor is connected between XIN and XOUT. 8-bit I/O port. The output structure is CMOS output. When this port is selected for input, pull-up transistors can be connected in units of 1 bit, and a key-on wake-up function is provided. 8-bit I/O port. The output structure is CMOS output. When this port is selected for input, pull-up transistors can be connected in units of 4 bits. P12 and P13 are in common with timer output pins T0 and T1. P14, P15, P16 and P17 are in common with serial I/O pins RXD, TXD, SCLK and ____ SRDY, respectively. 8-bit input port. (Only 4 bits of P20 to P23 for the 7480 group) or analog input pins IN0 to IN7 (IN0 to IN3 for the 7480 group). 4-bit input port. P30 and P31 can be configured to serve as external interrupt input pins INT0 and INT1. 4-bit I/O port. (2 bits of P40 and P41 for the 7480 group). The output structure is N-channel open drain output, having a built-in clamp diode. P40 and P41 can be configured to serve as timer I/O pins CNTR0 and CNTR1. 4-bit I/O port. (This port is not included in the 7480 group.) The output structure is N-channel open drain output, having built-in clamp diodes.
RESET XIN XOUT
P00 - P07
I/O port P0
I/O
P10 - P17
I/O port P1
I/O
P20 - P27 P30 - P33
Input port P2 Input port P3
Input
Input I/O
P40 - P43
I/O port P4
P50 - P53
I/O port P5
I/O
9
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL DESCRIPTION Central Processing Unit (CPU)
The 7480/7481 group uses the standard 740 family CPU. Refer to the table of 740 family addressing modes and machine instructions or the MELPS 740 programming manual for details on the instruction set. Machine-resident 740 family instructions are as follows: 1. The FST and SLW instructions are not available. 2. The MUL and DIV instructions are available. 3. The WIT instruction is available. (Note) 4. The STP instruction is available. (Note) Note: When using these instructions, refer to the corresponding chapter "STP and WIT instruction control" below.
CPU Mode Register
The stack page selection bit is assigned to the CPU mode register. This register is allocated at address 00FB16.
b7
b0
CPU mode register (CPUM: address 00FB16) Not used. These bits must always be set to "0".
Stack page selection bit (Note) 0 : Page 0 1 : Page 1
Watchdog timer L count source selection bit 0 : f(XIN)/8 1 : f(XIN)/16 Not used (undefined at read) System clock division proportion selection bit 0 : f = f(XIN)/2 (high-speed mode) 1 : f = f(XIN)/8 (medium-speed mode) Not used (undefined at read) Note : In the models of RAM size under 192 bytes, set this bit to "0".
Fig. 7 Structure of CPU mode register
10
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Memory
* SFR Area This SFR area is provided in the zero page and contains the registers for controlling I/O ports and timers. * RAM RAM is used for data storage and for calling subroutines, as well as for a stack area for interrupts. * ROM ROM is used for storing user programs and interrupt vectors.
* Interrupt Vector Area The interrupt vector area is used for storing vector addresses when an interrupt is generated or at reset. * Zero Page This area can be accessed with 2 words when the zero page addressing mode is used. * Special Page This area can be accessed with 2 words when the special page addressing mode is used.
000016 RAM (192 bytes) for M37480M4, M37480M8/E8, M37481M4, M37481M8/E8 RAM (128 bytes) for M37480M2, M37481M2 007F16 008016 00BF16 00C016 00FF16 010016 RAM (64 bytes) for M37480M4, M37481M4 Zero page
SFR area
RAM (256 bytes) for M37480M8/E8, M37481M8/E8
013F16
01FF16 Not used C00016 E00016 ROM (16384 bytes) for M37480M8/E8, M37481M8/E8 F00016 ROM (8192 bytes) for M37480M4, M37481M4 ROM (4096 bytes) for M37480M2, M37481M2 FF0016 FFE416 Interrupt vector area FFFF16 Special page
Fig. 8 Memory map
11
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
00C016 00C116 00C216 00C316 00C416 00C516 00C616 00C716 00C916 00C916 00CA16 00CB16 00CC16 00CD16 00CE16 00CF16 00D016 00D116 00D216 00D316 00D416 00D516 00D616 00D716 00D816 00D916 00DB16 00DC16 00DD16
Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P3 (P3) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) (Note) Port P5 direction register (P5D) (Note)
00E016 00E116 00E216 00E316 00E416 00E516 00E616 00E716 00E816 00E916 00EA16 00EB16 00EC16 00ED16 00EE16 00EF16
Transmit/receive buffer register (TB/RB) Serial I/O status register (SIOSTS) Serial I/O control register (SIOCON) UART control register (UARTCON) Baud rate generator (BRG) Bus collision detection control register (BUSARBCON)
Watchdog timer H (WDTH) Timer X low-order (TXL) Timer X high-order (TXH) Timer Y low-order (TYL) Timer Y high-order (TYH) Timer 1 (T1) Timer 2 (T2) Timer X mode register (TXM) Timer Y mode register (TYM) Timer XY control register (TXYCON) Timer 1 mode register (T1M) Timer 2 mode register (T2M) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2)
Port P0 pull-up control register (P0PCON) Port P1 pull-up control register (P1PCON) Port P4P5 input control register (P4P5CON)
00F016 00F116 00F216 00F316 00F416 00F516 00F616 00F716 00F816
Edge polarity selection register (EG)
A-D control register (ADCON)
00F916 00FA16 00FB16 00FC16 00FD16 00FE16 00FF16
00DA16 A-D conversion register (AD)
00DE16 STP instruction operation control register (STPCON) 00DF16
Fig. 9 SFR (Special Function Register) memory map Note: This port is not allocated in the 7480 group.
12
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
I/O Ports
[Direction Registers] The I/O ports have direction registers which determine the input/ output direction of each pin in units of bit. When a bit of the direction register is set to "1", the corresponding pin becomes an output port. When the bit is cleared to "0", it becomes an input port. If data is read from a pin configured as output, the value of the port latch is read rather than the value of this pin. A pin configured as input becomes floating and its value can be read. If data is written to a pin, it is written to the port latch, but the pin remains floating.
b7
b0 Port P0 pull-up control register (P0PCON : address 00D016) P00 pull-up control bit P01 pull-up control bit P02 pull-up control bit P03 pull-up control bit P04 pull-up control bit P05 pull-up control bit P06 pull-up control bit P07 pull-up control bit 0 : Pull-up transistor OFF 1 : Pull-up transistor ON
[Pull-up Control Registers] Ports P0 and P1 are provided with a programmable pull-up transistor. When "1" is written to the pull-up control register and the direction register is in the input mode, the pull-up transistor turns on, and the port is pulled up. s Notes on Use for STP Instruction When the 7480/7481 group is executing an STP instruction, apply 0 V or the same voltage as Vcc to the following pins. If an intermediate voltage is applied to these pins, a through-current flows to the input gates and the power current increases. P4, P5, P3, P16, P14 [Port P4P5 Input Control Register] When ports P42, P43 and P5 of the 7481 group are selected for input, clear the corresponding direction register to "0" and set "1" to the corresponding bit of the port P4P5 input control register. Ports P42, P43 and P5 are not included in the 7480 group. Fix each bit of the port P4P5 input control register to "0".
b7
b0
Port P4P5 input control register (P4P5CON : address 00D216) P42, P43 input control bit P5 input control bit (For the 7480 group) Set this bit to "0". (For the 7481 group) Set this bit to "1". Not used ("0" at read)
b7
b0 Port P1 pull-up control register (P1PCON : address 00D116) P13 - P10 pull-up control bit P17 - P14 pull-up control bit Not used (undefined at read) 0 : Pull-up transistor OFF 1 : Pull-up transistor ON
Fig. 11 Structure of port P4P5 input control register
Fig. 10 Structure of pull-up control register
13
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Port P0 Pull-up control register
Direction register
Tr1
Data bus
Port latch Port P0
Interrupt control circuit
Ports P10 - P13
Data bus
Pull-up control register T2M1
Direction register
Tr2
Data bus
Port latch Port P13
T1 Tr3 T1M1
Direction register
Data bus
Port latch Port P12
T0 Tr4
Direction register
Data bus
Port latch Port P11
Tr5
Direction register
Data bus
Port latch Port P10
Tr1 to Tr5 are pull-up transistors.
Fig. 12 Block diagram of ports (1)
14
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Ports P14 - P17 SIOE SIOM SRDY Tr6
Direction register
Data bus
Port latch Port P17
SRDY SCS SIOE
SIOM SIOE Tr7
Direction register
Data bus
Port latch Port P16
SCLK output SIOE TE
SCLK input
Tr8
Direction register
Data bus
Port latch Port P15
TXD SIOE RE Tr9
Direction register
Data bus
Port latch Port P14
RXD Data bus Pull-up control register
Tr6 to Tr9 are pull-up transistors.
Fig. 13 Block diagram of ports (2)
15
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Port P2 Data bus Port P2 A-D conversion circuit Multiplexer
Port P3 Data bus INT0, INT1 Port P3
Port P40, P41
Timer X,Y operating mode bits
"001" "100" "101" "110"
Direction register
Data bus
Port latch
Port P40, P41
Timer output
CNTR0, CNTR1 input
Port P42, P43, P50, P51, P52, P53
Direction register
Data bus
Port latch
Port P42, P43, P50, P51, P52, P53
Port P4 P5 input control register (For the 7480 group) Set this bit to "0". (For the 7481 group) Set this bit to "1".
Fig. 14 Block diagram of ports (3)
16
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Interrupts
Interrupts are vectored interrupts, and they can be caused by 14 different sources: 5 external sources, 8 internal sources, and 1 software source. (1) Interrupt Control All interrupts, except the BRK instruction interrupt, have an interrupt request bit and an interrupt enable bit. Additionally, a global interrupt disable flag affects them. When the interrupt enable bit and the interrupt request bit are set to "1" and the interrupt disable flag is set to "0", an interrupt is accepted. The interrupt request bits can be cleared by the program but cannot be set. The interrupt enable bit can be set and cleared by the program. The reset and BRK instruction interrupt can never be disabled. Other interrupts are disabled when the interrupt disable flag is set.
(2) Interrupt Operation When an interrupt request is accepted: 1. The contents of the program counter and the processor status register are automatically pushed into the stack. 2. The interrupt disable flag is set and the interrupt request bit is cleared. 3. The interrupt jump destination address is read into the program counter. s Notes * When the active edge of an external interrupt (INT0, INT1, CNTR0, CNTR1) is set, the interrupt request bit may also be set. Therefore, disable the external interrupt and set the edge polarity selection register. Then clear the interrupt request bit and accept the external interrupt. * Input a trigger width over 250 ns to the INT0/INT1 pin.
17
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 4. Interrupt vector addresses and priority Interrupt source RESET (Note 2) INT0 INT1 3 Key-on wake-up CNTR0 CNTR1 Timer X Timer Y Timer 1 Timer 2 Serial I/O reception Serial I/O transmission Bus arbitration A-D conversion BRK instruction 4 5 6 7 8 9 10 11 12 13 14 FFF916 FFF716 FFF516 FFF316 FFF116 FFEF16 FFED16 FFEB16 FFE916 FFE716 FFE516 FFF816 FFF616 FFF416 FFF216 FFF016 FFEE16 FFEC16 FFEA16 FFE816 FFE616 FFE416 FFFB16 FFFA16 Priority 1 2 Vector address (Note 1) High-order Low-order FFFF16 FFFD16 FFFE16 FFFC16 Interrupt request generating conditions At reset At detection of either rising edge or falling edge of INT0 input At detection of either rising edge or falling edge of INT1 input At input "L" to port P0 in key-on wake-up mode At detection of either rising edge or falling edge of CNTR0 input At detection of either rising edge or falling edge of CNTR1 input At timer X underflow At timer Y underflow At timer 1 underflow At timer 2 underflow At completion of serial I/O data reception At completion of serial I/O transfer shift or when transmission buffer is empty At detection of bus collision At completion of A-D conversion At execution of BRK instruction Non-maskable software interrupt Remarks Non-maskable External interrupt (active edge programmable) External interrupt (active edge programmable) Validity after execution of STP/WIT instruction External interrupt (active edge programmable) External interrupt (active edge programmable)
Notes 1 : Vector addresses contain interrupt jump destination addresses. 2 : RESET is mentioned in the table because its operation is the same as an interrupt.
Interrupt request bit Interrupt enable bit Interrupt disable flag BRK instruction Reset Interrupt request
Fig. 15 Interrupt control diagram
18
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
Edge polarity selection register (EG : address 00D4 16)
INT0 selection bit 0 : Falling edge 1 : Rising edge INT1 selection bit 0 : Falling edge 1 : Rising edge CNTR0 edge selection bit 0 : In event count mode, count rising edge. : In pulse output mode, start at "H" level output. : In pulse cycle measurement mode, measure a period from falling edge to falling edge. : In pulse width measurement mode, measure an "H" period. : In programmable one-shot output mode, generate one-shot "H" pulse after start at "L" output. : Interrupt, falling edge active. 1 : In event count mode, count falling edge. : In pulse output mode, start at "L" level output. : In pulse cycle measurement mode, measure a period from rising edge to rising edge. : In pulse width measurement mode, measure an "L" period. : In programmable one-shot output mode, generate one-shot "L" pulse after start at "H" level output. : Interrupt, rising edge active. CNTR1 edge selection bit 0 : In event count mode, count rising edge. : In pulse output mode, start at "H" level output. : In pulse cycle measurement mode, measure a period from falling edge to falling edge. : In pulse width measurement mode, measure an "H" period. : In programmable one-shot output mode, generate one-shot "H" pulse after start at "L" level output. : Interrupt, falling edge active. 1 : In event count mode, count falling edge. : In pulse output mode, start at "L" output. : In pulse cycle measurement mode, measure a period from rising edge to rising edge. : In pulse width measurement mode, measure an "L" period. : In programmable one-shot output mode, generate one-shot "L" pulse after start at "H" output. : Interrupt rising edge active. Not used (undefined at read) INT1 source selection bit at STP or WIT 0 : P31/INT1 1 : P00 - P07 "L" level (for key-on wake-up) Not used (undefined at read)
b7 b0 b7 b0
Interrupt control register 1 (ICON1: address 00FE 16)
Interrupt request register 1 (IREQ1: address 00FC16)
Timer X interrupt enable bit Timer Y interrupt enable bit Timer 1 interrupt enable bit Timer 2 interrupt enable bit Serial I/O receive interrupt enable bit Serial I/O transmit interrupt enable bit Bus arbitration interrupt enable bit A-D conversion completion interrupt enable bit 0 : Interrupt disabled 1 : Interrupt enabled
b7 b0 b7 b0
Timer X interrupt request bit Timer Y interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit Serial I/O receive interrupt request bit Serial I/O transmit interrupt request bit Bus arbitration interrupt request bit A-D conversion completion interrupt request bit 0 : No interrupt request 1 : Interrupt requested
Interrupt control register 2 (ICON2: address 00FF16)
Interrupt request register 2 (IREQ2: address 00FD16)
INT0 interrupt enable bit INT1 interrupt enable bit CNTR0 interrupt enable bit CNTR1 interrupt enable bit 0 : Interrupt disable 1 : Interrupt enable Not used (undefined at read) 0 : Interrupt disabled 1 : Interrupt enabled
INT0 interrupt request bit INT1 interrupt request bit CNTR0 interrupt request bit CNTR1 interrupt request bit 0 : No interrupt request 1 : Interrupt request Not used (undefined at read) 0 : No interrupt request 1 : Interrupt requested
Fig. 16 Structure of registers related to interrupts
19
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Timers
The 7480/7481 group has two 16-bit timers (timer X and timer Y), and two 8-bit timers (timer 1 and timer 2). All the timers are of a count-down type. When the timer reaches "FF16" or "000016", an underflow occurs at the next count pulse and the corresponding timer latch is reloaded into the timer and the count is continued. When a timer underflows, the interrupt request bit corresponding to this timer is set to "1". At reading and setting the timer value to a 16-bit timer, be sure to read and set both high-order byte and low-order byte. At reading the count value from a 16-bit timer, read the high-order byte and the low-order byte in this order. At setting the count value in a 16-bit timer, set the low-order byte and the high-order byte in this order. The 16-bit timer cannot operate normally at reading during set operation or at setting during read operation. q Timer X, Timer Y Both timer X and timer Y are 16-bit timers independent from each other. They can select 7 operating modes by setting the mode registers. The registers related to timer X and timer Y are shown below. In the following, abbreviations will be used as register names. * Timer XY control register (TXYCON: address 00F816) * Port P4 direction register (P4D: address 00C916) * Timer X low-order (TXL: address 00F016) * Timer X high-order (TXH: address 00F116) * Timer Y low-order (TYL: address 00F216) * Timer Y high-order (TYH: address 00F316) * Timer X mode register (TXM: address 00F616) * Timer Y mode register (TYM: address 00F716) * Edge polarity selection register (EG: address 00D416) * Interrupt request register 1 (IREQ1: address 00FC16) * Interrupt request register 2 (IREQ2: address 00FD16) * Interrupt control register 1 (ICON1: address 00FE16) * Interrupt control register 2 (ICON2: address 00FF16) For register structures, refer to each register structural diagram. In the following, each mode will be described. (1) Timer Mode/Event Count Mode Timer Mode q Mode Selection This mode is selected by setting "000" in the timer X operating mode bits (b2b1b0) of TXM and the timer Y operating mode bits (b2b1b0) of TYM. q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt When a timer underflows, the timer X interrupt request bit (b0) or timer Y interrupt request bit (b1) of IREQ1 is set to "1". q Explanation of Operation After reset release, the timer X stop control bit (b0) or timer Y stop control bit (b1) of TXYCON is "1", and the timer stops. In the timer stop status, usually the timer value is set by writing the latch and timer at the same time. Timer operation is started by setting "0" in b0 or b1 of TXYCON. When the timer reaches "000016", an underflow occurs at the next count pulse, the corresponding timer latch is reloaded into the timer, and the count is continued. To change the timer value during count operation, the latch value is changed by writing to
the latch only. At the next underflow reloading, the timer value is changed. Event Count Mode q Mode Selection Select the timer event count mode. This mode is selected by inputting from the CNTR0 pin for timer X or from the CNTR1 pin for timer Y (setting "11" in b7 and b6 of TXM or "11" in b7 and b6 of TYM). The count operation active edge is selected by setting in the CNTR0 edge selection bit (b2) or the CNTR1 edge selection bit (b3) of EG. At "0", the rising edge is counted. At "1", the falling edge is counted. q Interrupt The underflow interrupt is the same as the timer mode. q Explanation of Operation This operation is the same as that of the timer mode. In this mode, set the port in common with the CNTR0/CNTR1 pin as an input port. Figure 19 shows a timing diagram in the timer event count mode. (2) Pulse Output Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "001". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16.
20
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Interrupt The timer underflow interrupt is the same as the timer event count mode. q Explanation of Operation This operation is the same as the timer event count mode except that a timer outputs a pulse from the CNTR0/CNTR1 pin in which the polarity of output level is inverted at each timer underflow. When the CNTR0 edge selection bit (b2) or CNTR1 edge selection bit (b3) of EG is "0", the output of the CNTR0/ CNTR1 pin is started with an "H" level output. When b2 or b3 of EG is "1", the output of this pin is started with an "L" level. In this mode, set the port in common with the CNTR0/CNTR1 pin as an output port. s Note While a timer operation stops The output level of the CNTR0/CNTR1 pin is initialized to the value set in the CNTR0 edge selection bit or CNTR1 edge selection bit by writing to the timer. While a timer operation is enabled The output level of the CNTR0/CNTR1 pin is inverted by changing the CNTR0 edge selection bit or CNTR1 edge selection bit. Figure 20 shows a timing diagram in the pulse output mode. (3) Pulse Cycle Measurement Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "010". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt The underflow interrupt is the same as the timer event count mode. Set b2 or b3 of IREQ2 to "1" as soon as the pulse cycle measurement is completed. q Explanation of Operation While a timer operation stops Select a timer count source. Next, select a pulse cycle to be measured. When b2 or b3 of EG is "0", a timer counts a period from a falling edge to a falling edge of the CNTR0/CNTR1 pin input. When b2 or b3 of EG is "1", a timer counts a period from a rising edge to a rising edge of the CNRT0/CNTR1 pin input. While a timer operation is enabled At setting b0 and b1 of TXYCON to "0", a timer starts to measure the pulse cycle, and starts to count down from the count value provided before measurement. When an active edge is detected at measurement completion or measurement start, 1's complement of the timer value is set to the timer latch and "FFFF16" is set in the timer. When a timer underflows, a timer X or timer Y interrupt occurs, and "FFFF16" is set in the timer. A measurement value is held until the next measurement is completed. In this mode, set the port in common with the CNTR0/CNTR1 pin as an input port. s Note The timer value cannot be read in this mode. A timer value can be set while a timer operation stops (no measurement). Since the timer latch of this mode becomes read only, do not perform a write operation during measurement. The timer is set to "FFFF16" only when the timer underflows or the active edge of pulse cycle measurement is detected. Accordingly, the timer value at a start of measurement depends on
the timer value provided before the start of measurement. Figure 21 shows a timing diagram in the pulse cycle measurement mode. (4) Pulse Width Measurement Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "011". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt The underflow interrupt is the same as the timer event count mode. Set b2 or b3 of IREQ2 to "1" as soon as pulse width measurement is completed. q Explanation of Operation While a timer operation stops Select a timer count source. Next, select a pulse width to be measured. A timer counts a period from a falling edge to a rising edge of the CNTR0/CNTR1 pin input ("L" period) when b2 or b3 of EG is "1". A timer counts a period from a rising edge to a falling edge of the CNTR0/CNTR1 pin input ("H" period) when b2 or b3 of EG is set to "0". While a timer operation is enabled At setting b0 and b1 of TXYCON to "0", a timer starts to measure a pulse width, and starts to count down from the count value provided before measurement. When the active edge is detected at measurement completion, 1's complement of the timer value is set in the timer latch. When the active edge is detected at measurement completion or measurement start, "FFFF16" is set in the timer. When a timer underflows, a timer X or timer Y interrupt occurs, and "FFFF16" is set in the timer. A measurement value is held until the next measurement is completed. In this mode, set the port in common with the CNTR0/CNTR1 pin as an input port.
21
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
s Note The timer value cannot be read in this mode. A timer value can be set while a timer operation stops (not under pulse width measurement). Since the timer latch of this mode becomes read only, do not perform a write operation during measurement. The timer is set to "FFFF16" only when a timer underflows or when the active edge of pulse width measurement is detected. Accordingly, the timer value at a start of measurement depends on the timer value provided before the start of measurement. Figure 22 shows a timing diagram in the pulse width measurement mode. (5) Programmable Waveform Generation Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "100". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt The underflow interrupt is the same as the timer event count mode. The INT0 interrupt request bit (b0) or INT1 interrupt request bit (b1) of IREQ2 is set to "1" by detecting an active edge of the INT pin. q Explanation of Operation This operation is the same as that of the timer event count mode, except that a timer outputs the level of the value set in the output level latch (b4) of TXM or TYM from the CNTR0/ CNTR1 pin each time the timer underflows. After the timer underflows, if the values of the output level latch and timer latch are changed, the timer can output an optional waveform from the CNTR0/CNTR1 pin. In this mode, set the port in common with the CNTR0/CNTR1 pin as an output port. In this mode, if the trigger selection bit of TXM or TYM is set to "1" and the count stop control bit of TXYCON is set to "0" (count operation), a timer can be started concurrently with the occurrence of a trigger (input signal of INT0/INT1 pin). A timer starting trigger is set in the INT0 edge selection bit (b0) or INT1 edge selection bit (b1) of EG. At "0", the falling edge is active. At "1", the rising edge is active. When the count stop control bit is "1" (count status), a timer is not started at the occurrence of a trigger. Figure 23 shows a timing diagram in the programmable waveform generation mode. (6) Programmable One-Shot Output Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "101". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt The underflow interrupt is the same as the timer event count mode. One-shot output trigger is set in the INT0 edge selection bit (b0) or INT1 edge selection bit (b1) of EG. At "0", the falling edge is active. At "1", the rising edge is active. The INT0 interrupt request bit (b0) or INT1 interrupt request bit (b1) of IREQ2 is set to "1" by detecting an active edge of the INT pin. q Explanation of Operation In case of One-shot Output "H"
(b2, b3 of EG = "0") While a timer operation stops The output level of the CNTR0/CNTR1 pin is initialized to "L" at mode selection. Set the one-shot width in TXH, TXL, TYH and TYL. While a timer operation stops, a trigger (input signal of INT0/INT1 pin) cannot occur. While a timer operation is enabled At detecting a trigger, a timer outputs "H" from the CNTR0/ CNTR1 pin, and outputs "L" at a timer underflow. In Case of One-shot Output "L" (b2, b3 of EG = "1") While a timer operation stops The output level of the CNTR0/CNTR1 pin is initialized to "H" at mode selection. Set the one-shot width in TXH, TXL, TYH and TYL. While a timer operation stops, a trigger (input signal of the INT0/INT1 pin) cannot occur. While a timer operation is enabled At the detection of a trigger, a timer outputs "L" from the CNTR0/ CNTR1 pin and outputs "H" at a timer underflow. In this mode, set the port in common with the CNTR0/CNTR1 pin as an output port. s Note q Input a trigger width over 250 ns to the INT0/INT1 pin. q If the value of the CNTR0 edge selection bit or CNTR1 edge selection bit is changed while one-shot output is enabled or one-shot output occurs, the output level from the CNTR0/ CNTR1 pin changes. Figure 24 shows a timing diagram in the programmable oneshot output mode.
22
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(7) PWM Mode q Mode Selection This mode is selected by setting b2, b1 and b0 of TXM or TYM to "110". q Count Source Selection The count source is f(XIN)/2, f(XIN)/8 or f(XIN)/16. q Interrupt At the rising edge of the CNTR0/CNTR1 output, set the timer X interrupt request bit (b0) or timer Y interrupt request bit (b1) of IREQ1 to "1". q Explanation of Operation In the case of timer X, the PWM waveform is output from the CNTR0 pin. In the case of timer Y, the PWM waveform is output from the CNTR1 pin. The PWM waveform "H" period is determined by the setting value n (n=0 to 255) of TXH or TYH. The "L" period is determined by the setting value m (m=0 to 255) of TXL or TYL. The PWM cycle is as follows: PWM cycle = (n + m) ! ts PWM output duty = n (n + m)
same time. At writing only to the timer latch, when the write timing for the timer latch is almost equal to the underflow timing, the value that is set in the timer may not be constant. q Read Control for Timer X/Timer Y When the pulse cycle measurement mode or pulse width measurement mode is selected, the timer value cannot be read out. In the other modes, the timer value can be read regardless of count operation and count stop. However, the timer latch value cannot be read out. q Note on CNTR0, CNTR1, INT0, INT1 Interrupt Polarity Selection When the CNTR0/CNTR1 edge selection bit or INT0/INT1 interrupt edge selection bit is set, this affects the respective interrupt polarity.
ts: Timer X/timer Y count source cycle While a timer operation stops The timer value is set in TXL, TXH, TYL and TYH by writing to the timer and timer latch at the same time. The output of the CNTR0/CNTR1 pin is initialized to "H" by setting this timer value. While a timer operation is enabled When b1 and b0 of TXYCON are set to "0", "H" is output during the period of the setting value of TXH or TYH. After that, "L" is output during the period of the setting value of TXL or TYL. Then, these operations will be repeated. The PWM output subsequent to an underflow can be changed by setting the timer value in TXL, TXH, TYL, TYH by writing only to the timer latch. In this mode, set the port in common with the CNTR0/CNTR1 pin as an output port. s Note q When the PWM "H" period is set to "0016", the PWM output is always "L" level. q When the PWM "L" period is set to "0016", the PWM output is always "H" level. q When the PWM "H" period is set to "0016" and the "L" period is set to "0016", the PWM output is always "L" level. q When at least one of the PWM "H" period and "L" period is set to "0016", a timer X interrupt request/timer Y interrupt request does not occur. q When the timer latch is set at "0016", the timer counts down, so its value is not constant. Figure 25 shows a timing diagram in the PWM mode. s Note on All Modes q Write Control for Timer X, Timer Y Timer X and timer Y can select either writing to both timer latch and timer or writing only to the timer latch by b3 of TXM or TYM. At writing only to the timer latch, a value is set in the timer latch by writing the value in the timer X/timer Y address, so the timer is updated at the next underflow. After reset release, writing to both the timer latch and timer is selected. At this status, when a value is written in the timer X/timer Y address, the value is set in both the timer and timer latch at the
23
MITSUBISHI MICROCOMPUTERS
e. n. ang atio cific ct to ch spe inal e subje a f ar not s is is ric limit t : Th tice arame No e p Som
PRE
L
Y NAR IMI
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
"1" P30/INT0 "0" INT0 edge selection bit Programmable one-shot output mode PWM mode Programmable one-shot output circuit
CNTR0 edge selection bit "1" "0"
Programmable one-shot output mode Data bus
PWM mode PWM generating circuit Programmable waveform generation mode
INT0 interrupt request
Output level latch
D T
Q Pulse output mode S T Q Q CNTR0 edge selection bit "0"
"001" "100" "101" "110" Timer X operating mode bits P40 direction register
P40 latch
"1"
Pulse output mode
Timer X (low-order) latch Timer X (high-order) latch Timer X (low-order) Timer X (high-order) Timer X interrupt request
Pulse width measurement mode Pulse cycle measurement mode CNTR0 edge selection bit "1" P40/CNTR0 "0" f(XIN)/2 f(XIN)/8 f(XIN)/16 "0"
D T Q
Edge detecting circuit Timer X count source selection bit CNTR0 interrupt request
Programmable waveform generation mode Timer X trigger selection bit Timer X stop control bit
"1" CNTR1 edge selection bit "1" "0" INT1 interrupt request Programmable one-shot output mode
"1" P31/INT1 "0" INT1 edge selection bit Programmable one-shot output mode PWM mode Programmable waveform generation mode Output level latch D
T
Programmable one-shot output circuit
PWM mode PWM generating circuit
Q Pulse output mode
S T
"001" "100" "101" "110" Timer Y operating mode bits P41 direction register
Q Q
CNTR1 edge selection bit "0"
P41 latch
"1"
Pulse output mode
Timer Y (low-order) latch Timer Y (high-order) latch Timer Y (low-order) Timer Y (high-order) Timer Y interrupt request
Pulse width measurement mode Pulse cycle measurement mode CNTR1 edge selection bit "1" P41/CNTR1 "0" f(XIN)/2 f(XIN)/8 f(XIN)/16 "0"
D T Q
Edge detecting circuit
CNTR1
Timer Y count source selection bit
interrupt request
Programmable waveform generation mode Timer Y trigger selection bit Timer Y stop control bit
"1"
Fig. 17 Block diagram of timer X and timer Y
24
PR
e. n. atio chang cific o spe bject t l fina su ot a its are is n m This etric li m ice: Not e para Som
MI ELI
Y NAR
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
b7
b0
Timer X mode register (TXM : address 00F6 16)
Timer Y mode register (TYM : address 00F716)
Timer X operating mode bits b2 b1 b0 0 0 0 : Timer event count mode 0 0 1 : Pulse output mode 0 1 0 : Pulse cycle measurement mode 0 1 1 : Pulse width measurement mode 1 0 0 : Programmable waveform generation mode 1 0 1 : Programmable one-shot output mode 1 1 0 : PWM mode 1 1 1 : Not used Timer X write control bit 0 : Writing to both latch and timer 1 : Writing to latch only Output level latch 0 : "L" output 1 : "H" output Timer X trigger selection bit 0 : Timer X free run in programmable waveform generation mode 1 : Trigger occurrence (input signal of INT 0 pin) and timer X start in programmable waveform generation mode.
Timer Y operating mode bits b2 b1 b0 0 0 0 : Timer event count mode 0 0 1 : Pulse output mode 0 1 0 : Pulse cycle measurement mode 0 1 1 : Pulse width measurement mode 1 0 0 : Programmable waveform generation mode 1 0 1 : Programmable one-shot output mode 1 1 0 : PWM mode 1 1 1 : Not used Timer Y write control bit 0 : Writing to both latch and timer 1 : Writing to latch only Output level latch 0 : "L" output 1 : "H" output Timer Y trigger selection bit 0 : Timer Y free run in programmable waveform generation mode 1 : Trigger occurrence (input signal of INT 1 pin) and timer Y start in programmable waveform generation mode.
Timer X count source selection bits b7 b6 0 0 : f(XIN)/2 0 1 : f(XIN)/8 1 0 : f(XIN)/16 1 1 : Input from CNTR0 pin
Timer Y count source selection bits b7 b6 0 0 : f(XIN)/2 0 1 : f(XIN)/8 1 0 : f(XIN)/16 1 1 : Input from CNTR1 pin
b7
b0
Timer XY control register (TXYCON : address 00F8 16)
Timer X stop control bit 0 : Count operation 1 : Count stop Timer Y stop control bit 0 : Count operation 1 : Count stop Not used (all "0" at read)
Fig. 18 Structure of timer X/timer Y mode register and timer XY control register
25
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FFFF16 TL
000016 TR TR TR
TL : Value set in timer latch TR : Timer interrupt request
Fig. 19 Timing diagram in timer mode/event count mode
FFFF16 TL
000016 TR TR TR TR
Output waveform from CNTR0/CNTR1 pin CNTR CNTR TL : Value set in timer latch TR : Timer interrupt request CNTR : CNTR0/CNTR1 interrupt request (CNTR polarity selection bit "0" : falling edge active)
Fig. 20 Timing diagram in pulse output mode
26
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
000016
T3 T2 T1 FFFF16 TR FFFF16+T1 T2 T3 FFFF16 TR
Input signal from CNTR0/CNTR1 pin CNTR CNTR CNTR CNTR CNTR0/CNTR1 interrupt polarity is active at rising edge. TR : Timer interrupt request CNTR: CNTR0/CNTR1 interrupt request
Fig. 21 Timing diagram in pulse cycle measurement mode (at "rising edge interval" measurement)
000016
T3 T2 T1 FFFF16 TR FFFF16+T2 T3 T1
Input signal from CNTR0/CNTR1 pin CNTR CNTR CNTR CNTR0/CNTR1 interrupt polarity is active at rising edge, and pulse L width is measured. TR : Timer interrupt request CNTR : CNTR0/CNTR1 interrupt request
Fig. 22 Timing diagram in pulse width measurement mode (at "L section" measurement)
27
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FFFF16 T3 L T2 T1 000016 TR L TR T1 T3 TR T2 TR
Input signal from INT0/INT1 pin Output waveform from CNTR0/CNTR1 pin CNTR L : Initial value of TL H, TLL TR : Timer interrupt request CNTR : CNTR0/CNTR1 interrupt request (CNTR polarity selection bit "0" : falling edge active)
Fig. 23 Timing diagram in programmable waveform generation mode (when trigger selection bit = "1")
CNTR
FFFF16 L
000016 Input signal from INT0/INT1 pin L Output waveform from CNTR0/ CNTR1 pin
TR
TR
TR
L
L
CNTR CNTR L : One-shot pulse width TR : Timer interrupt request CNTR : CNTR0/CNTR1 interrupt request (CNTR polarity selection bit "0" : falling edge active)
CNTR
Fig. 24 Timing diagram in programmable one-shot output mode
28
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ts Timer X/timer Y count source
Timer X/timer Y PWM output n!t s (n+m)!t s TR CNTR TR m!t s
CNTR : CNTR0/CNTR1 interrupt request (CNTR polarity selection bit "0" : falling edge active) TR : Timer interrupt Note : A PWM waveform with duty n/(n+m) and cycle (n+m) ! ts is output. * TXH/TYH setting value: n= 0 - 255 * TXL/TYL setting value: m = 0 - 255 * Timer X/timer Y count source cycle: ts * n+m = 0 - 510
Fig. 25 Timing diagram in PWM mode
29
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
q Timers 1 and 2 Timer 1 and timer 2 are the 8-bit timers. They can select the following 2 modes by setting timer 1 mode register and timer 2 mode register. * Timer mode * Programmable waveform generation mode When the count source is changed, set it again as the timer value may go wrong.
(1) Timer Mode The frequency of f(XIN)/8, f(XIN)/64, f(XIN)/128 or f(XIN)/256 is counted. (2) Programmable Waveform Generation Mode This operation is the same as the timer mode, except that a timer outputs the level of the value set in the output level latch of the timer 1 mode register/timer 2 mode register from the T0 or T1 pin each time a timer underflows. After the timer underflows, the timer can output an optional waveform from the T0 or T1 pin if the values of the output level latch and timer latch are changed. In this mode, set the port in common with the T0/T1 pin as an output port.
Data bus 8
Timer count source selection bits f(XIN)/8 f(XIN)/64 f(XIN)/128 f(XIN)/256
"00" "01" "10" "11"
TL
Count stop control bit
T
8
Timer interrupt request bit
T
T0, T1 output
Q
D
Output level latch
8
Timer mode register 8
Data bus
Fig. 26 Block diagram of timer 1, timer 2
b7
b0
Timer 1 mode register (T1M : address 00F916) Timer 2 mode register (T2M : address 00FA 16) Timer stop control bit 0 : Count operation 1 : Count stop Timer operation mode bit 0 : Timer mode 1 : Programmable waveform generation mode Not used ("0" at read) Output level latch 0 : "L" output 1 : "H" output Not used ("0" at read) Timer count source selection bits b7 b6 0 0 : f(XIN)/8 0 1 : f(XIN)/64 1 0 : f(XIN)/128 1 1 : f(XIN)/256
Fig. 27 Structure of timer 1/timer 2 mode register
30
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Serial I/O
Serial I/O can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer (baud rate generator) is also provided for baud rate generation when serial I/O is in operation. (1) Clock Synchronous Serial I/O Mode The clock synchronous serial I/O mode can be selected by setting
the serial I/O mode selection bit of the serial I/O control register (address 00E216) to "1". In the clock synchronous serial I/O, the transmitter-side microcomputer and the receiver-side microcomputer must use the same clock for serial I/O operation. If an internal clock is used as operating clock, a transfer is started by a write signal to the transmit/ receive buffer register.
Data bus P16 RXD
Receive enable bit (RE)
P14
Address 00E016 Receive buffer register Receive shift register Shift clock
Serial I/O control register
Address 00E216
Receive buffer full flag (RBF) Receive interrupt request (RI) Clock control circuit
SCLK
Serial I/O enable bit (SIOE) Serial I/O synchronous BRG count source Frequency division clock selection selection bit (CSS) ratio 1/(n+1) bit (SCS) Baud rate generator 1/4
XIN
1/4
SRDY output enable bit (SRDY)
1/4
Falling edge detection Transmit shift register
Address 00E416 Clock control circuit Transmit shift register shift completion flag (TSC) Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Serial I/O status register Address 00E116
SRDY TXD
F/F
Transmit enable bit (TE)
Transmit interrupt source selection bit (TIC)
P17
P15
Transmit buffer register Address 00E016
Data bus
Fig. 28 Block diagram of clock synchronous serial I/O
Transmit/receive shift clock, 1/8 - 1/8192 of internal clock, or external clock
Serial output TxD Serial input RxD Receive enable signal SRDY Write signal to receive/ transmit buffer register (address 00E016)
D0 D0
D1 D1
D2 D2
D3 D3
D4 D4
D5 D5
D6 D6
D7 D7
TBE = 0 TBE = 1 TSC = 0
RBF = 1 TSC = 1 Overrun error (OE) detection
Notes 1 : The transmit interrupt (TI) can be selected to be generated either when the transmit buffer is empty (TBE = 1) or after the transmit shift operation is completed (TSC = 1) by using the transmit interrupt source selection bit (TIC) of the serial I/O control register. 2 : If data is written to the transmit buffer register when TSC = 0, the transmit clock is generated continuously, and serial data is output continuously from the TxD pin. 3 : The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes "1".
Fig. 29 Operation of clock synchronous serial I/O function
31
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(2) Asynchronous Serial I/O (UART) Mode The UART mode can be selected by clearing the serial I/O mode selection bit of the serial I/O control register to "0". Eight serial data transfer formats can be selected, and the transfer formats to be used by a transmitter and a receiver must be identical.
Each of the transmit and receive registers has a buffer register (the same address on memory). Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register and receive data is read from the receive buffer register. These buffer registers can also hold the next data to be transmitted and receive 2-byte receive data in succession.
Data bus
P14 RXD
Receive enable bit (RE) ST detection
Address 00E216 Address 00E016
Serial I/O control register
Receive buffer full flag (RBF) Receive interrupt request (RI)
OE
Receive buffer register Receive shift register
7-bit 8-bit
Character length selection bit (CHAS)
PE
FE
SP detection
1/16
UART control register
Address 00E316
Clock control circuit
Serial I/O enable bit (SIOE) Serial I/O synchronous clock selection bit (SCS)
SCLK XIN
BRG count source selection bit (CSS)
Serial I/O synchronous clock selection bit (SCS)
Frequency division ratio 1/(n+1)
1/4 1/4
Baud rate generator Address 00E416 ST/SP/PA generation
1/16
Transmit shift register shift completion flag (TSC) Transmit interrupt request (TI) Transmit buffer empty flag (TBE) Address 00E116
Transmit enable bit (TE)
TXD P16 P15
Transmit shift register
Transmit interrupt source selection bit (TIC)
Character length selection bit Transmit (CHAS)
buffer register
Address 00E016 Data bus
Serial I/O status register
Fig. 30 Block diagram of UART serial I/O
Transmit or receive clock Transmit buffer register write signal TBE=0 TSC=0 TBE=1 Serial output TxD TBE=0 TBE=1 TSC=1 *
ST
D0
D1
1 start bit 7/8 data bit 1/0 parity bit 1/2 stop bit
SP
ST
D0
D1
SP
VGenerated at 2nd bit in 2
Receive buffer register read signal
stop bit mode
RBF=0 RBF=1 RBF=1
Serial input RxD
ST
D0
D1
SP
ST
D0
D1
SP
Notes 1 : Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit during reception). 2 : The transmit interrupt (TI) can be selected to be generated when either TBE=1 or TSC=1, depending on the setting of the transmit interrupt source selection bit of the serial I/O control register. 3 : The receive interrupt (RI) is set when the RBF flag becomes "1".
Fig. 31 Operation of UART serial I/O function
32
PR
e. n. atio chang cific o spe bject t l fina su ot a its are is n m This etric li m ice: Not e para Som
MI ELI
Y NAR
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
[Serial I/O Control Register] SIOCON The serial I/O control register consists of 8 control bits for control of the serial I/O. [UART Control Register] UARTCON The UART control register is a 4-bit control register which is valid when UART is selected. This 4-bit control register sets a data format for serial data transfer. [Serial I/O Status Register] SIOSTS This is a 7-bit read-only register consisting of flags that indicate the serial I/O operating status and different error flags. The 3 bits of bit 4 to bit 6 are valid only in the UART mode. The receive buffer full flag is cleared to "0" when the receive buffer register is read. If there is an error, it is detected at the same time that data is transferred from the receive shift register to the receive buffer register, and the receive buffer full flag is set. Writing to the serial I/O status register clears all the error flags (OE, PE, FE, SE). All the bits of this register are initialized to "0" at reset. However, if the transmit enable bit of the serial I/O control register is set to "1", bit 2 and bit 0 become "1". [Transmit Buffer Register/Receive Buffer Register] TB/RG The transmit buffer register and the receive buffer register are located at the same address. The transmit buffer register is a write-only type and the receive buffer register is a read-only type. If a character bit length is 7 bits, the MSB of the receive data stored in the receive buffer is "0". [Baud Rate Generator] BRG The baud rate generator determines a baud rate for serial transfer. The baud rate generator, being an 8-bit counter with a reload register, divides the frequency of the count source by 1/(n+1), where n is the value written to the baud rate generator.
b7
b0
Serial I/O status register SIOSTS (address 00E116) Transmit buffer empty flag (TBE) 0 : Buffer full 1 : Buffer empty Receive buffer full flag (RBF) 0 : Buffer empty 1 : Buffer full Transmit shift register shift completion flag (TSC) 0 : Transmit shift in progress 1 : Transmit shift completed Overrun error flag (OE) 0 : No error 1 : Overrun error Parity error flag (PE) 0 : No error 1 : Parity error Framing error flag (FE) 0 : No error 1 : Framing error Summing error flag (SE) 0 : (OE)U(PE)U(FE)=0 1 : (OE)U(PE)U(FE)=1 Not used ("1" at read)
b7
b0
Serial I/O control register SIOCON (address 00E216) BRG count source selection bit (CSS) 0 : f(XIN)/4 1 : f(XIN)/16 Serial I/O synchronous clock selection bit (SCS) 0 : BRG output/4 (when clock synchronous serial I/O is selected) BRG output/16 (when UART is selected) 1 : External clock input (when clock synchronous serial I/O is selected) External clock input/16 (when UART is selected) SRDY output enable bit (SRDY) 0 : P17 pin operates as ordinary I/O pin. 1 : P17 pin operates as SRDY output pin. Transmit interrupt source selection bit (TIC) 0 : Interrupt when transmit buffer is empty. 1 : Interrupt when transmit shift operation is completed. Transmit enable bit (TE) 0 : Transmit disabled 1 : Transmit enabled Receive enable bit (RE) 0 : Receive disabled 1 : Receive enabled Serial I/O mode selection bit (SIOM) 0 : Asynchronous serial I/O (UART) 1 : Clock synchronous serial I/O Serial I/O enable bit (SIOE) 0 : Serial I/O disabled (P14 to P17: ordinary I/O ports) 1 : Serial I/O enabled (P14 to P17: serial I/O function pins)
b7
b0
UART control register UARTCON (address 00E316) Character length selection bit (CHAS) 0 : 8-bit 1 : 7-bit Parity enable bit (PARE) 0 : Parity disabled 1 : Parity enabled Parity selection bit (PARS) 0 : Even parity 1 : Odd parity Stop bit length selection bit (STPS) 0 : 1 stop bit 1 : 2 stop bits Not used ("1" at read)
Fig. 32 Structure of serial I/O related registers (SIOSTS, UARTCON, SIOCON)
33
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Bus Arbitration Interrupt
The 7480/7481 group is provided with a built-in bus arbitration interrupt as a function for bus conflict system communication. At such bus conflict system communication, as shown in Figure 33, if transmit data cannot be transmitted to the LAN data bus due to a transmit data collision, the data collision can be detected by the bus arbitration interrupt.
LAN data bus
7480/7481 group serial I/O
TxD
Interface driver/ receiver
RxD
Fig. 33 Example of bus conflict system communication
34
MITSUBISHI MICROCOMPUTERS
e. n. ang atio cific ct to ch spe inal e subje a f ar not s is is ric limit t : Th tice arame No e p Som
PRE
L
Y NAR IMI
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Bus Collision Detection
The 7480/7481 group can detect a bus collision by setting the bus collision detection enable bit to "1". When transmission is started in the clock synchronous or asynchronous (UART) serial I/O mode, the transmit pin TxD is compared with the receive pin RxD in synchronization with a rising edge of transmit shift clock. If they do not coincide with each other, a bus arbitration interrupt request occurs (bus collision detection).
A transmit data collision is detected between LSB and MSB of transmit data in the clock synchronous serial I/O mode or between the start bit and stop bit of transmit data in the UART mode. Bus collision detection can be performed by both the internal clock and the external clock. A block diagram is shown in Figure 34. A timing diagram is shown in Figure 35. A bus collision detection control register is shown in Figure 36.
TXD RXD
D
Q
Bus arbitration interrupt request
Shift clock
Bus collision detection enable bit
TE
Fig. 34 Block diagram of bus arbitration interrupt circuit
Transmit shift clock Transmit pin TxD Receive pin RxD Data collision
Fig. 35 Timing diagram of bus arbitration interrupt
Bus arbitration interrupt generation
b7
b0
Bus collision detection control register (BUSARBCON address 00E5 16)
Bus collision detection enable bit 0 : Collision detection disabled 1 : Collision detection enabled Not used ("0" at read)
Fig. 36 Structure of bus collision detection control register
35
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Application Example Priority Control at Simplified SAEJ1850
At simplified SAEJ1850 communication, when multiple units start to transmit data at the same time, priority control is exerted. On the LAN data bus, the "H" level has priority over the "L" level. When an "H" level collides with an "L" level, the LAN data bus status goes to the "H" level. For example, when unit A outputs "H" and unit B outputs "L" at the same time in Figure 37, the LAN data bus goes to "H". Accordingly, unit A takes priority of control and continues its transmission, and unit B stops its transmission immediately. In this way, the 7480/7481 group exerts priority control for each bit and finally allows only the highest-priority unit to transmit data.
BU S+ LAN data bus BU S-
Unit A
Unit B
Continue to transmit Unit A Unit B LAN data bus Data collision Stop transmitting
Fig. 37 Priority control at simplified SAEJ1850
36
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
A-D Converter
For A-D conversion, the 8-bit successive comparison method is used. Figure 38 shows a block diagram of A-D conversion. Conversion is automatically performed once started by the program. There are 8 analog input pins that are in common with P27 to P20 of port P2 (4 pins of P23 to P20 in the 7480 group). Pin inputs to be A-D converted are selected by bit 2 to bit 0 of the A-D control register (address 00D916). Bit 3 of the A-D control register is an A-D conversion completion bit. This bit is "0" during A-D conversion and "1" after completion of it. Accordingly, it is possible by checking this bit to know whether A-D conversion is completed or not. Figure 39 shows the relationship between the contents of the A-D control register and input pins to be selected. The A-D conversion register (address 00DA16) stores conversion results, so it is possible to know them by reading the contents of this register.
Next, the procedure for executing A-D conversion will be explained below. First, set values in bit 2 to bit 0 of the A-D control register and select pins to be A-D converted. Next, clear the A-D conversion completion bit to "0". With this write operation, A-D conversion is started. The A-D conversion is completed after the lapse of 50 machine cycles (12.5 s at f(XIN)= 8 MHz), and the A-D conversion completion bit is set to "1". The A-D conversion interrupt request bit is also set to "1". Conversion results are stored in the A-D conversion register.
Data bus
b4
b0
A-D control register (address 00D916)
P20/IN0 P21/IN1
Channel selector
A-D control circuit
A-D conversion completion interrupt request
P22/IN2 P23/IN3 P24/IN4 P25/IN5 P26/IN6 P27/IN7
Comparator
A-D conversion register (address 00DA16)
Switch tree Ladder resistor
VSS (Note 1)
VREF
Notes 1 : AVSS for the 44P6N package of the 7481 group. 2 : The 7480 group is not provided with P2 4/IN4 to P27/IN7.
Fig. 38 Block diagram of A-D converter circuit
37
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
b7
b0
A-D control register ADCON (address 00D916) Analog input pin selection bits 000 : P20/IN0 001 : P21/IN1 010 : P22/IN2 011 : P23/IN3 100 : P24/IN4 101 : P25/IN5 (Note) 110 : P26/IN6 111 : P27/IN7 A-D conversion completion bit 0 : Conversion in progress 1 : Conversion completed VREF connection selection bit 0: Disconnect between VREF pin and ladder resistor 1: Connect between VREF pin and ladder resistor Not used (undefined at read) Note : Do not perform setting in the 7480 group.
Fig. 39 Structure of A-D control register
38
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Watchdog Timer
The watchdog timer gives a means for returning to a reset status when the program fails to run on its normal loop due to a runaway. The watchdog timer consists of a 7-bit watchdog timer L and an 8bit watchdog timer H. q Initial Value of Watchdog Timer By a reset or writing to the watchdog timer H, the watchdog timer H is set to "FF16" and the watchdog timer L is set to "7F16". Any instruction that permits generating a write signal can be used; for example, STA, LDM, CLB, etc. Write data has no significance, so the above values are set regardless of that data. q Operation of Watchdog Timer The watchdog timer stops at reset, and writing a value in the watchdog timer H causes it to start to count down. When bit 7 of the watchdog timer H becomes "0", an internal reset occurs. The reset status is released as soon as the release reset time is
up. After that, the 7480/7481 group runs the program from the reset vector address. It is programmed that the watchdog timer H can be set before bit 7 of the watchdog timer H is cleared to "0". If the watchdog timer H is never written, the watchdog timer does not function. When the STP instruction is executed, the clock stops and the watchdog timer also stops. The count is restarted as soon as the stop mode is released. (Note) On the other hand, the watchdog timer does not stop after execution of the WIT instruction. The timing from writing to the watchdog timer H to clearing bit 7 of the watchdog timer H to "0" is shown below. (f(XIN)=8 MHz) * When bit 3 of the CPU mode register is "0" ............. 16.384 ms * When bit 3 of the CPU mode register is "1" ............ 32.768 ms Note: Since the watchdog timer still counts for the stop release waiting time (about 2048 cycles of XIN), bit 7 of the watchdog timer H should not be cleared to "0" in this period.
Data bus Write "7F16" to the watchdog timer register Write "FF16" to the watchdog timer register
1/8
"0" Watchdog timer L (7) Watchdog timer H (8) bit7
f(XIN)
1/16 "1" Watchdog timer L count source selection bit
Reset circuit
RESET
Internal reset
Fig. 40 Block diagram of watchdog timer
39
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
STP/WIT Instruction Control
The STP instruction and the WIT instruction can be enabled or disabled selectively by using the STP instruction operation control register. To cope with a program runaway after reset, the STP instruction and the WIT instruction are disabled in the initial status.
The STP and WIT instructions can be set as enable/disable only by writing to the STP instruction operation control register twice successively so as not to stop the oscillation clock even if a write data error is caused by program runaway. Figure 41 shows a structure of the STP instruction operation control register.
b7
b0 STP instruction operation control register (STPCON: address 00DE 16) STP instruction and WIT instruction enable/disable selection bit (Note) 0 : STP/WIT instruction enabled 1 : STP/WIT instruction disabled
Not used ("0" at read) Note : The STP instruction and the WIT instruction are disabled in the initial status. When using these instructions, set bit 0 of the STP instruction operation control register to "1", then set this bit to "0". (Writing twice successively) When not using the STP and WIT instructions, set this bit to "1" either once or twice.
Fig. 41 Structure of STP instruction operation control register
Explanation of STP Instruction Operation Control Register
The STP instruction operation control register will be enabled by writing data to the same address twice successively. If data is not written in continuous form, the written data is not valid but the previous value is held.
If an interrupt is received while the same data is written twice, there is a possibility that the write instruction in the interrupt routine may be executed. For this reason, rewriting is required after interrupt disable. Figure 42 shows a reference example of data rewriting.
qSTP/WIT instruction enable
* * *
qSTP/WIT instruction disable
* * *
SEI LDM #01H, 0DEH LDM #00H, 0DEH CLI
* * *
Interrupt disable in this period
SEI LDM #01H, 0DEH LDM #01H, 0DEH CLI
* * *
Interrupt disable in this period
Use only in interrupt enable status
Use only in interrupt enable status
Fig. 42 Reference example of data rewriting
40
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Recovery From Power-down Status By Key Input Interrupt (Key-on wake-up)
"Key-on wake-up" is one way of recovery from a power-down status by using the STP or WIT instruction. If an "L" level voltage is input to any pin of port P0 when bit 5 of the edge polarity selection register is "1", an interrupt occurs, and a recovery can be made to the normal operating state. If a key
matrix of active "L" with port P0 as an input port is constructed, a recovery can be made to the normal operating status by pressing a key. The key input interrupt is in common with the INT1 interrupt. When bit 5 of the edge polarity selection register is set to "1", the key input interrupt function is selected. If this bit is set to "1" except in the power-down status, both INT1 and key-on wake-up are invalidated.
P41/CNTR1 Port P41 data read circuit CNTR1 interrupt request signal
EG3
P40/CNTR0 Port P40 data read circuit CNTR0 interrupt request signal
EG2
P30/INT0 Port P30 data read circuit INT0 interrupt request signal
EG0
P31/INT1 Port P31 data read circuit
EG1 EG5
INT1 interrupt request signal
CPU stop status signal Pull-up control register
P07
Direction register
Pull-up control register
P01
Direction register
Port P0 data read circuit
Pull-up control register
P00
Direction register
Fig. 43 Block diagram of interrupt input/key-on wake-up circuit
41
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Clock Generating Circuit
The 7480/7481 group is provided with a built-in oscillation circuit. An oscillation circuit can be formed by connecting a resonator between XIN and XOUT. Use the manufacturer's recommended values for constants such as capacitance, which will differ depending on each resonator. The 7480/7481 group has a built-in feedback resistor between the XIN and XOUT pins, so an external resistor can be omitted. q Frequency Control (1) High-speed Mode The frequency applied to the clock input pin XIN divided by 2 is used as the internal clock . This mode is set after reset release. (2) Medium-speed Mode The frequency applied to the clock input pin XIN divided by 8 is used as the internal clock . q Oscillation Frequency (1) Stop Mode If the STP instruction is executed, the internal clock stops at an "H" level, and the oscillator stops. At this time, timer 1 is set to "FF16," and f(XIN)/8 is forcibly connected to the count source of timer 1. Accordingly, set the timer 1 interrupt enable bit to the disable status ("0") before execution of the STP instruction. When a reset or an external interrupt is accepted, oscillation is restarted, but the internal clock is supplied to the CPU after timer 1 underflows. This is because when an external resonator is used, some time is required until a start of oscillation. (2) Wait Mode If the WIT instruction is executed, the internal clock stops at an "H" level. But, the oscillator does not stop. When a reset or interrupt is accepted, the stop status is released. The microcomputer can execute any instruction immediately, because the oscillator does not stop.
XIN
XOUT Rd
CIN
COUT
Fig. 44 External circuit of ceramic resonator
XIN
XOUT Open VCC
External oscillation circuit
VSS Duty ratio 50%
Fig. 45 External clock input circuit
42
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
XIN
XOUT 1/2 1/4 CM6 "1" "0" Internal clock Timer 1
1/4
QS R STP instruction WIT instruction
SQ R
Q QS R R
Reset STP instruction
Reset Interrupt disable flag Interrupt request
Fig. 46 Block diagram of clock generating circuit
43
MITSUBISHI MICROCOMPUTERS
e. n. ang atio cific ct to ch spe inal e subje a f ar not s is is ric limit t : Th tice arame No e p Som
PRE
L
Y NAR IMI
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Reset Circuit
The microcomputer is put into a reset status by holding the _____ RESET pin at the "L" level for 2s or more when the power source voltage is 2.7 to 5.5 V and XIN is in stable oscillation. _____ After that, this reset status is released by returning the RESET pin to the "H" level. The program starts from the address having the contents of address FFFF16 as high-order address and the contents of address FFFE16 as low-order address. Note that the reset input voltage should be 0.32 V or less when the power source voltage passes 2.7 V.
Power ON
RESET
VCC
Power source voltage 0V Reset input voltage 0V
(Note)
0.12VCC
Note : Reset release voltage VCC = 2.7 V
RESET
VCC
Power source voltage detecting circuit
Fig. 47 Reset circuit diagram
XIN RESET Internal reset Address Data SYNC
XIN 2048 clock cycle Notes 1 : The frequency relation between f(X IN) and is f(XIN)=2*f(). 2 : The mark "?" means that the address is changeable depending on the previous state. ? ? ? ? FFFE16 FFFF16 ADH,L Reset address from the vector table
?
?
?
?
ADL
ADH
Fig. 48 Reset sequence
44
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
(1) (2) (3) (4) (5) (6)
Port P0 direction register (P0D) Port P1 direction register (P1D) Port P4 direction register (P4D) Port P5 direction register (P5D) Port P0 pull-up control register (P0PCON) Port P1 pull-up control register (P1PCON)
Address b7 (C116) * * * (C316) * * * (C9 16) * * * (CB16) * * * (D016) * * * (D116) * * * (D216) * * * (D416) * * * (D916) * * *
b0 0016 0016 0000 0000 0016 00 0016 0 0000 01000
( 7 ) Port P4P5 input control register (P4P5CON) ( 8 ) Edge polarity selection register (EG) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26) (27) (28) (29) (30) (31) A-D control register (ADCON) STP instruction operation control register (STPCON) Serial I/O status register (SIOSTS) Serial I/O control register (SIOCON) UART control register (UARTCON) Bus collision detection control register (BUSARBCON) Watchdog timer H (WDTH) Timer X low-order (TXL) Timer X high-order (TXH) Timer Y low-order (TYL) Timer Y high-order (TYH) Timer 1 (T1) Timer X mode register (TXM) Timer Y mode register (TYM) Timer XY control register (TXYCON) Timer 1 mode register (T1M) Timer 2 mode register (T2M) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2) Program counter (PC H) (PCL) (32) Processor status register (PS)
(DE16) * * * 0 0 0 0 0 0 0 1 (E116) * * * 1 0 0 0 0 0 0 0 (E216) * * *
0016
(E316) * * * 1 1 1 1 0 0 0 0 (E516) * * * (EF16) * * * (F0 16) * * * (F1 16) * * * (F2 16) * * * (F3 16) * * * (F416) * * * (F6 16) * * * (F7 16) * * *
0016 FF16 FF16 FF16 FF16 FF16 FF16 0016 0016
(F816) * * * 0 0 0 0 0 0 1 1 (F916) * * * (FA16) * * * (FB 16) * * * (FC 16) * * * (FD 16) * * * (FE 16) * * * (FF 16) * * *
0016 0016 0 0000 0016 0000 0016 0000
Contents of address FFFF16 Contents of address FFFE16
1
: At reset release, the read value is undefined. Note : Some kinds of microcomputers do not use some of these bits. Refer to the structure of each register.
Fig. 49 Internal state of microcomputer at reset
45
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
BUILT-IN PROGRAMMABLE ROM VERSIONS M37480E8-XXXSP/FP, M37480E8T-XXXSP/FP, M37481E8-XXXSP/FP, M37481E8T-XXXSP/FP, M37481E8SS PIN DESCRIPTION
Table 5. Pin description Pin VCC, VSS AVSS (Note 1) Mode Single-chip/ EPROM Single-chip VREF EPROM
_____
Name
Input/ output
Function
Power source Reference power input Mode input Reset input Reset input Clock input Clock output
Apply a voltage of 2.7 to 5.5 V to VCC and 0 V to VSS and AVSS.
Input Input Input Input Input Output
Reference voltage input pin for A-D converter.
__
Used as CE input pin. Reset input pin. Connect to VSS. These are I/O pins of internal clock generating circuit for the main clock. To control generating frequency, an external ceramic resonator is connected between XIN and XOUT pins. If an external clock is used, the clock oscillation source should be connected to the XIN pin, and the XOUT pin should be left open. Feedback resistor is connected between XIN and XOUT. 8-bit I/O port. The output structure is CMOS output. When this port is selected for input, a pull-up transistor can be connected in units of 1 bit, and a key-on wake-up function is provided. Data 8-bit (D0 to D7) I/O pins 8-bit I/O port. The output structure is CMOS output. When this port is selected for input, a pull-up transistor can be connected in units of 4 bits. P12 and P13 are in common with timer output pins T0 and T1. P14, P15, P16 and P17 are in common with ____ serial I/O pins RxD, TxD, SCLK and SRDY. P11 to P17 are address (A4 to A10) input pins. Leave P10 open. 8-bit input port. This port is in common with analog input pins IN0 to IN7 (IN0 to IN3 for the 7480 group). P20 to P23 are address (A0 to A3) input pins. Leave P24 to P27 open. 4-bit input port. P30 and P31 are in common with external interrupt input pins INT0 and INT1.
__
Single-chip EPROM Single-chip/ EPROM Single-chip/ EPROM Single-chip
RESET
XIN XOUT
P00 - P07 EPROM
I/O port P0 Data I/O D0 - D7
I/O I/O
Single-chip P10 - P17 EPROM Single-chip EPROM Single-chip P30 - P33 EPROM
I/O port P1
I/O
Address input A4 - A10 Input port P2 Address input A0 - A3 Input port P3 Address input A11, A12, mode input, VPP input I/O port P4 Address input A13, A14 I/O port P5 Input port P5
Input Input Input Input
P20 - P27 (Note 2)
Input
P30 and P31 are address (A11, A12) input pins. P32 is used for OE input. P33 is VPP input. Apply VPP in the program and program verify modes. 4-bit I/O port. The output structure is N-channel open drain output, having built-in clamp diode. P40 and P41 are in common with timer input pins CNTR0 and CNTR1. P40 and P41 are address (A13, A14) input pins. Leave P42 and P43 open. 4-bit I/O port. The output structure is N-channel open drain output, having a built-in clamp diode. Leave these pins open.
P40 - P43 (Note 3)
Single-chip
I/O
EPROM P50 - P53 (Note 4) Single-chip EPROM
Input I/O Input
Notes 1 : This is a dedicated pin for the 44P6N-A package in the 7481 group. 2 : Only 4 bits of P20 to P23 (IN0 to IN3) for the 7480 group. 3 : Only 2 bits of P40 and P41 for the 7480 group. 4 : This is a dedicated pin for the 7481 group.
46
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
EPROM MODE
The built-in programmable ROM has the EPROM mode in addition _____ to its normal operation modes. When the RESET level becomes "L", the chip automatically enters the EPROM mode. Table 6 shows a list of correspondence between pins and Figure 50 to Figure 52 show pin connection diagrams. In this status, each of ports P0, P11 to P17, P20 to P23, P3, P40, P41 and VREF are used for the PROM (equivalent to M5M27C256K). In this mode, the built-in PROM can be written to or read from using these pins in the same way as with the M5M27C256K. The clock should be connected to XIN and XOUT pins.
Table 6. Correspondence between pins in EPROM mode M37480E8, M37481E8 VCC VPP VSS Ports Address input Data I/O __ CE __ OE VCC P33 VSS P11 - P17, P20 - P23, P30, P31, P40, P41 Port P0 VREF P32 M5M27C256K VCC VPP VSS A0 - A14 D0 - D7 __ CE __ OE
A10 A9 A8 A7 A6 A5 A4
A3 A2 A1 A0
CE
VSS
P53 P17/SRDY P16/SCLK P15/TXD P14/RXD P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 2 3 4 5 6
42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
P52 P07 P06 P05 P04 P03 P02 P01 P00 P43 P42 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1 P30/INT0 RESET P51 P50 VCC
D7 D6 D5 D4 D3 D2 D1 D0
Outline 42P4B 42S1B-A (M37481E8SS) : PROM pin (equivalent to M5M27C256K)
M37481E8-XXXSP M37481E8T-XXXSP M37481E8SS
A14 A13 VPP
OE
A12 A11
VSS VCC
Fig. 50 Pin connection in EPROM mode (1)
47
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
VPP
25
A14
A13
28
31
30
27
24
32
33
29
26
23
P03 P02 P01 P00 P43 P42 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1
D4 D5 D6 D7 VSS A10 A9 A8 A7
A12
22 21 20 19
P04 P05 P06 P07 P52 VSS P53 P17/SRDY P16/SCLK P15/TXD P14/RXD
34 35 36 37 38 39 40 41 42 43 44
10 11 1 2 3 4 5 6 7 8 9
OE
D3
D2
D1
D0
P30/INT0 RESET P51 P50 VCC VSS AVSS XOUT XIN VREF P20/IN0
A11
VSS VCC VSS
M37481E8-XXXFP M37481E8T-XXXFP
18 17 16 15 14 13 12
CE A0
A6
A5
A4
A3
A2
Outline 44P6N-A
: PROM pin (equivalent to M5M27C256K)
Fig. 51 Pin connection in EPROM mode (2)
A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
CE
VSS
P17/SRDY P16/SCLK P15/TXD P14/RXD P13/T1 P12/T0 P11 P10 P23/IN3 P22/IN2 P21/IN1 P20/IN0 VREF XIN XOUT VSS
1 2 3 4
32 31 30 29
A1
P13/T1 P12/T0 P11 P10 P27/IN7 P26/IN6 P25/IN5 P24/IN4 P23/IN3 P22/IN2 P21/IN1
5 6 7 8 9 10 11 12 13 14 15 16
28 27 26 25 24 23 22 21 20 19 18 17
P07 P06 P05 P04 P03 P02 P01 P00 P41/CNTR1 P40/CNTR0 P33 P32 P31/INT1 P30/INT0 RESET VCC
D7 D6 D5 D4 D3 D2 D1 D0 A14 A13 VPP
OE
Outline 32P4B 32P2W-A : PROM pin (equivalent to M5M27C256K)
Fig. 52 Pin connection in EPROM mode (3)
M37480E8-XXXSP/FP M37480E8T-XXXSP/FP
A12 A11
VCC
VSS
48
MITSUBISHI MICROCOMPUTERS
ge ion. icat to chan ecif l sp ubject a a fin es not mits ar li is is : Th metric ice Not e para Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
FUNCTIONAL DESCRIPTION OF PROM VERSION Reading __ __
To read the PROM, set the CE and OE pins to "L" level, and set stored contents will appear to the address signal (A0 to A14). The __ __ data I/O pins (D0 to D7). When the CE and OE pins are set to "H" level, the data I/O pins will be put into a floating status.
NOTES ON HANDLING
(1) Sunlight and fluorescent light contain wavelengths capable of erasing data. For use in the read mode, be sure to cover the transparent window with a seal. (Ceramic package type) (2) We can supply the seal with which the transparent window is covered. Be careful not to allow the seal to contact the microcomputer lead pins. (Ceramic package type) (3) Before erasing, clean the transparent glass. If the glass is smeared with greasy hands or paste, ultraviolet light transmission will be prevented, having a negative effect on erasing characteristics. (Ceramic package type) (4) Since a high voltage is used for writing data, care should be taken not to apply an overvoltage when turning on the power source. (5) For the programmable microcomputers (one-time programmable version, version shipped in blank), Mitsubishi does not perform PROM write testing and screening in the assembly process and subsequent processes. To improve reliability after writing, perform writing and testing according to the following operation flow before use.
Writing
__
To write to the PROM, apply "H" to the OE pin and VPP to the VPP pin to set the program mode. Select addresses to be written to with address input pins (A0 to A14) and give write data to the data input pins (D0 to D7) in 8-bit parallel form. In this status, when the __ CE pin becomes "L", writing will be started.
Notes on Writing
When using a PROM programmer, specify the address range to address 400016 to address 7FFF16. When data is written between address 000016 and address 7FFF16, fill addresses 000016 to 3FFF16 with "FF16".
Erasing
Data can be erased only on the ceramic package with window M37481E8SS. To erase data on this chip, use an ultraviolet light source with a 2537 Angstrom wave length. The minimum radiation power required for erasing is 15W*s/cm2.
Writing with PROM programmer
Screening (Leave at 150C for 40 hours.) (Note)
Verify test with PROM programmer
Function check in target device
Note : The screening temperature is up to 150C. Never expose to 150C exceeding 100 hours. The M37480E8SP/FP, M37481E8SP/FP and M37481E8SS are not T versions (mountable on vehicles), so it is impossible to mount them on vehicles. The M37481E8SS is for user program evaluation, so it is impossible to mount it on vehicles or on user's mass-production real machines.
Fig. 53 Writing and testing for one-time programmable version
49
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
I/O SIGNALS IN EACH MODE
Table 7. I/O signals in each mode Pin Mode Read-out Output disable Programming Programming verify Program disable
__ __
CE VIL VIL VIL VIH VIH
OE VIL VIH VIH VIL VIH
VPP VCC VCC VPP VPP VPP
VCC VCC VCC VCC VCC VCC
Data I/O Output Floating Input Output Floating
Note : VIL and VIH denote an "L" input voltage and an "H" input voltage, respectively.
50
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ADDRESSING MODES
The 7480/7481 group has strong accessability, because it has 17 kinds of addressing modes. For details, refer to the 740 family addressing modes.
DATA REQUIRED FOR MASK ORDERING
Please submit the following data when placing mask orders. (1) Mask ROM confirmation form (2) Mark specification form (3) ROM data .......................................................... EPROM 3 sets
MACHINE-LANGUAGE INSTRUCTIONS
The 7480/7481 group has 71 machine-language instructions. For details, refer to the 740 family machine-language instruction list.
DATA R E QU I R E D F O R RO M W R I T I N G ORDERING
Please submit the following data when placing ROM writing orders. (1) ROM writing confirmation form (2) Mark specification form (3) ROM data .......................................................... EPROM 3 sets
NOTES ON PROGRAMMING
(1) The frequency division ratio of the timer is 1/(n+1). n: Timer setting value However, n = 0 - 255 (for timer 1, timer 2) n = 0 - 65535 (timer X, timer Y) (2) The contents of the interrupt request bits can be changed by software, but the values will not change immediately after being overwritten. After changing the value of the interrupt request bits, execute at least one instruction before executing a the BBC or BBS instruction. (3) To calculate in decimal notation, set the decimal mode flag (D) to "1". After executing the ADC or SBC instruction, execute another instruction before executing the SEC, CLC, or CLD instruction. (4) A NOP instruction should be executed after every PLP instruction. (5) Do not execute the STP instruction during A-D conversion. (6) Multiplication and Division Instructions The index X mode (T) and the decimal mode (D) flags do not affect the MUL and DIV instructions. The execution of these instructions does not change the contents of the processor status register.
51
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37480M4/M8/E8-XXXSP/FP, M37480M2T/M4T/M8T/E8T-XXXSP/FP ABSOLUTE MAXIMUM RATINGS (7480 Group)
Table 8. Absolute maximum ratings Symbol VCC VI VO Pd Topr Tstg Parameter Power source voltage Input voltage Output voltage Power dissipation Operating temperature range Storage temperature Condition All voltages are measured on the basis of the VSS pin. Output transistors are cut off. Ta = 25 C Rated value -0.3 to 7 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 1000 (Note 1) -20 to 85 (Note 2) -40 to 150 (Note 3) Unit V V V mW C C
Notes 1 : 500 mW for 32P2W-A package type. 2 : -40 to 85 C for extended operating temperature range version. 3 : -65 to 150 C for extended operating temperature range version.
RECOMMENDED OPERATING CONDITIONS (7480 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85C (Note 1) unless otherwise specified) Table 9. Recommended operating conditions Symbol Parameter f(XIN) = (2.2VCC - 2) MHz f(XIN) = 8 MHz Standard values Min. 2.7 4.5 Typ. 3 5 0 0.8 VCC 0.7 VCC VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V VIH VIH VIL VIL VIL "H" input voltage P40 - P41 (Note 4)
_____
Max. 4.5 5.5
Unit V V V
VCC VSS VIH VIH VIH
Power source voltage Power source voltage "H" input voltage P00 - P07, P10 - P17 "H" input voltage P20 - P23 "H" input voltage P30 - P33
VCC VCC VCC VCC VCC VCC VCC 0.2 VCC 0.25 VCC 0.4 VCC 0.3 VCC 0.4 VCC 0.3 VCC 0.16 VCC 0.12 VCC 1 - 30 - 30 60 60 - 10 20 -5 10
V V V V V V V V V V V V V V V mA mA mA mA mA mA mA mA mA
0.8 VCC 0.9 VCC 0.8 VCC 0.9 VCC 0.8 VCC 0 0
VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
"H" input voltage XIN, RESET "L" input voltage P00 - P07, P10 - P17 "L" input voltage P20 - P23 "L" input voltage P30 - P33 VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
0 0 0 0 0 0
VIL VIL VIL II IOH(sum) IOH(sum) IOL(sum) IOL(sum) IOH(peak) IOL(peak) IOH(avg) IOL(avg)
"L" input voltage P40 - P41 "L" input voltage XIN
_____
VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
"L" input voltage RESET Input current P40 - P41 (Note 4) VI > VCC "H" sum output current P00 - P07 "H" sum output current P10 - P17 "L" sum output current P00 - P07, P40 - P41 "L" sum output current P10 - P17 "H" peak output current P00 - P07, P10 - P17 "L" peak output current P00 - P07, P10 - P17, P40 - P41 "H" average output current P00 - P07, P10 - P17 (Note 2) "L" average output current P00 - P07, P10 - P17, P40 - P41 (Note 2)
52
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 9. Recommended operating conditions (cont.) Symbol Parameter Timer input frequency CNTR0 (P40), CNTR1 (P41) (Note 3) Clock synchronous f(SCLK) Serial I/O clock input frequency SCLK (P16) (Note 3) serial I/O mode UART mode f(XIN) = 4 MHz f(XIN) = 8 MHz f(XIN) = 4 MHz f(XIN) = 8 MHz f(XIN) = 4 MHz f(XIN) = 8 MHz VCC = 2.7 to 4.5 V VCC = 4.5 to 5.5 V Standard values Min. Typ. Max. 1 2 250 500 1 2 2.2VCC - 2 8 Unit
f(CNTR)
MHz
kHz
MHz
f(XIN)
Clock input oscillation frequency (Note 3)
MHz
Notes 1 : -40 to 85 C for extended operating temperature range version. 2 : The average output currents IOH(avg) and IOL(avg) are the average values during 100 ms. 3 : The clock input oscillation frequency is at 50 % duty ratio. 4 : When applying a voltage through a resistor as shown in the figure 54, VI > VCC may be accepted if the current is 1 mA or less.
VI
The clamp diode of the 7480/7481 group is designed for a level shift of DC signal unlike ordinary switching diodes. Do not apply sudden stress, such as rush current, directly to the diode.
I Port P4
Notes on Countermeasures for Noise and Latch-up (7480 Group)
(1) Connect a bypass capacitor (0.1F) across the VCC pin and the VSS pin with the shortest possible wiring, using a relatively thick wire. (2) Connect a bypass capacitor (0.01 F) across the VREF pin and the VSS pin with the shortest possible wiring, using a relatively thick wire. (3) In the oscillation circuit, connect across the XIN and XOUT pins with the shortest possible wiring. Connect the GND and VSS pins of the oscillation circuit with the shortest possible wiring, using a relatively thick wire. (4) In the case of the P33/VPP pin of the built-in programmable ROM version, connect an approximately 5 k resistor to the P33/VPP pin the shortest possible in series.
Fig. 54 Note on use of port P4
Notes on Clamp Diode (7480 Group)
(1) Total input current The current of port P4 through the clamp diode can be drawn up to 1.0 mA per port. When a current that cannot be consumed by microcomputer is sent to the clamp diode, this may raise the power source pin voltage of the microcomputer. The system power circuit must be designed so that the power source voltage of the microcomputer may be stabilized within standard values. (2) Maximum input voltage If the input voltage of a signal connected to port P4 is beyond VCC + 0.3 V, the input waveform should have a delay exceeding 2 s/V from the moment that this waveform goes over the voltage. For using a CR circuit for delay, calculate a proper delay value by the following expression: dt = dv t 0.6 ! VIN 2 ! 10-6 (s/V)
where VIN = Maximum input voltage amplitude margin and t = C ! R.
53
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37480M4/M8/E8-XXXSP/FP, M37480M2T/M4T/M8T/E8T-XXXSP/FP ELECTRICAL CHARACTERISTICS (7480 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85 C (Note 1) unless otherwise specified) Table 10. Electrical characteristics Symbol Parameter "H" output voltage P00 - P07, P10 - P17 "L" output voltage P00 - P07, P10 - P17, P40 - P41 Hysteresis P00 - P07, P30 - P33, P40 - P41 (Note 2) Hysteresis P16/SCLK, P14/RXD
_____
Test conditions VCC = 5 V, IOH = -5 mA VCC = 3 V, IOH = -1.5 mA VCC = 5 V, IOL = 10 mA VCC = 3 V, IOL = 3 mA VCC = 5 V VCC = 3 V When used as SCLK, RxD input VCC = 5 V VCC = 3 V VI = VCC without pull-up transistor VI = VCC = 5 V VI = VCC = 3 V VI = VCC when analog input is not selected VI = VCC (XIN at stop) VI = 0 V without pull-up VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VI = 0 V VI = 0 V when analog input is not selected VI = 0 V (XIN at stop) VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V
Standard values Min. 3 2 2 1 0.5 0.3 0.5 0.3 0.5 0.3 5 3 5 3 5 3 5 3 -5 -3 -0.25 -0.08 -0.5 -0.18 -1.0 -0.35 -5 -3 -5 -3 -5 -3 Typ. Max.
Unit
VOH
V
VOL
V
VT + - VT-
V
VT + - VT-
V
VT + - VT-
Hysteresis RESET "H" input current P00 - P07, P10 - P17 "H" input current P30 - P33, P40 - P41 "H" input current P20 - P23
_____
V
IIH
A
IIH
A A A
IIH
IIH
"H" input current RESET, XIN
IIL
"L" input current P00 - P07, P10 - P17
transistor VI = 0 V with pull-up transistor (Note 3)
A
mA
IIL
"L" input current P30 - P33, P40 - P41 "L" input current P20 - P23
_____
A
IIL
A A
IIL
"L" input current RESET, XIN
Notes 1 : -40 to 85 C for extended operating temperature range version. 2 : At using P0 for key-on wake-up function. 3 : Can be indicated in resistance value as shown below: When VCC = 5 V: 5 k (min.), 10 k (typ.), 20 k (max.). When VCC = 3 V: 8.6 k (min.), 16.7 k (typ.), 37.5 k (max.).
54
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37480M4/M8/E8-XXXSP/FP, M37480M2T/M4T/M8T/E8T-XXXSP/FP
Table 10. Electrical characteristics (cont.) Symbol VRAM Parameter RAM retention voltage Test conditions At clock stop mode In high-speed mode, f(XIN) = 4 MHz, VCC = 5 V A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress VCC = 5 V In high-speed mode, f(XIN) = 4 MHz In wait mode In high-speed mode, f(XIN) = 8 MHz VCC = 3 V VCC = 5 V VCC = 5 V In medium-speed mode, f(XIN) = 4 MHz In medium-speed mode, f(XIN) = 8 MHz In stop mode f(XIN) = 0 VCC = 5 V VCC = 3 V VCC = 5 V Ta = 25 C Ta = 85 C Standard values Min. 2 3.5 4 1.8 2 7 7.5 1.75 2 0.9 1 3.5 3.75 1 0.5 2 0.9 0.45 1.8 0.1 1 7 8 3.6 4 14 15 3.5 4 1.8 2 7 7.5 2 1 4 1.8 0.9 3.6 1 10 mA mA Typ. Max. Unit V mA mA mA mA mA mA mA mA mA mA mA mA
In high-speed mode, f(XIN) = 4 MHz, VCC = 3 V
In operating mode ICC Power source current
In high-speed mode, f(XIN) = 8 MHz, VCC = 5 V
In medium-speed mode, f(XIN) = 4 MHz, VCC = 5 V
In medium-speed mode, f(XIN) = 4 MHz, VCC = 3 V
In medium-speed mode, f(XIN) = 8 MHz, VCC = 5 V
A A
55
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37480M4/M8/E8-XXXSP/FP, M37480M2T/M4T/M8T/E8T-XXXSP/FP A-D CONVERSION CHARACTERISTICS (7480 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85 C (Note) unless otherwise specified) Table 11. A-D conversion characteristics Symbol ---- ---- TCONV Resolution Absolute accuracy (except quantization error) Conversion time VCC = VREF = 5.0 V VCC = 2.7 to 5.5 V, f(XIN) = 4 MHz VCC = 4.5 to 5.5 V, f(XIN) = 8 MHz VCC = 2.7 to 4.0 V VCC = 4.0 to 5.5 V 2 0.5 VCC 12 0 VREF = 5.0 V 50 143 35 Parameter Test conditions Standard values Min. Typ. Max. 8 2 25 12.5 VCC VCC 100 VREF 416 Unit bits LSB
s
VVREF RLADDER VIA IVREF
Reference voltage Ladder resistance Analog input voltage Reference input current
V k V
A
Note: -40 to 85 C for extended operating temperature range version.
56
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37481M4/M8/E8-XXXSP/FP, M37481M2T/M4T/M8T/E8T-XXXSP/FP, M37481E8SS ABSOLUTE MAXIMUM RATINGS (7481 Group)
Table 12. Absolute maximum ratings Symbol VCC VI VO Pd Topr Tstg Parameter Power source voltage Input voltage Output voltage Power dissipation Operating temperature range Storage temperature Condition All voltages are measured on the basis of the VSS pin. Output transistors are cut off. Ta = 25 C Rated value -0.3 to 7 -0.3 to VCC + 0.3 -0.3 to VCC + 0.3 1000 (Note 1) -20 to 85 (Note 2) -40 to 150 (Note 3) Unit V V V mW C C
Notes 1 : 500 mW for 44P6N-A package type. 2 : -40 to 85 C for extended operating temperature range version. 3 : -65 to 150 C for extended operating temperature range version.
RECOMMENDED OPERATING CONDITIONS (7481 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85C (Note 1) unless otherwise specified) Table 13. Recommended operating conditions Symbol Parameter f(XIN) = (2.2VCC - 2) MHz f(XIN) = 8 MHz Standard values Min. 2.7 4.5 Typ. 3 5 0 0.8 VCC 0.7 VCC VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V VIH VIH VIL VIL VIL "H" input voltage P40 - P43, P50 - P53 (Note 4)
_____
Max. 4.5 5.5
Unit V V V
VCC VSS VIH VIH VIH
Power source voltage Power source voltage "H" input voltage P00 - P07, P10 - P17 "H" input voltage P20 - P27 "H" input voltage P30 - P33
VCC VCC VCC VCC VCC VCC VCC 0.2 VCC 0.25 VCC 0.4 VCC 0.3 VCC 0.4 VCC 0.3 VCC 0.16 VCC 0.12 VCC 1 -30 -30 60 60 -10 20 -5 10
V V V V V V V V V V V V V V V mA mA mA mA mA mA mA mA mA
0.8 VCC 0.9 VCC 0.8 VCC 0.9 VCC 0.8 VCC 0 0
VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
"H" input voltage XIN, RESET "L" input voltage P00 - P07, P10 - P17 "L" input voltage P20 - P27 "L" input voltage P30 - P33 VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
0 0 0 0 0 0
VIL VIL VIL II IOH(sum) IOH(sum) IOL(sum) IOL(sum) IOH(peak) IOL(peak) IOH(avg) IOL(avg)
"L" input voltage P40 - P43, P50 - P53 "L" input voltage XIN
_____
VCC = 4.5 to 5.5 V VCC = 2.7 to 4.5 V
"L" input voltage RESET Input current P40 - P43, P50 - P53 (Note 4) VI > VCC "H" sum output current P00 - P07 "H" sum output current P10 - P17 "L" sum output current P00 - P07, P40 - P43, P50 - P52 "L" sum output current P10 - P17, P53 "H" peak output current P00 - P07, P10 - P17 "L" peak output current P00 - P07, P10 - P17, P40 - P43, P50 - P53 "H" average output current P00 - P07, P10 - P17 (Note 2) "L" average output current P00 - P07, P10 - P17, P40 - P43, P50 - P53 (Note 2)
57
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Table 13. Recommended operating conditions (cont.) Symbol Parameter Timer input frequency CNTR0 (P40), CNTR1 (P41) (Note 3) Clock synchronous f(SCLK) Serial I/O clock input frequency SCLK (P16) (Note 3) serial I/O mode UART mode f(XIN) = 4 MHz f(XIN) = 8 MHz f(XIN) = 4 MHz f(XIN) = 8 MHz f(XIN) = 4 MHz f(XIN) = 8 MHz VCC = 2.7 to 4.5 V VCC = 4.5 to 5.5 V Standard values Min. Typ. Max. 1 2 250 500 1 2 2.2VCC - 2 8 Unit
f(CNTR)
MHz
kHz
MHz
f(XIN)
Clock input oscillation frequency (Note 3)
MHz
Notes 1 : -40 to 85 C for extended operating temperature range version. 2 : The average output currents IOH(avg) and IOL(avg) are the average values during 100 ms. 3 : The clock input oscillation frequency is at 50 % duty ratio. 4 : When applying a voltage through a resistor as shown in the figure 55, VI > VCC may be accepted if the current is 1 mA or less.
VI
The clamp diode of the 7480/7481 group is designed for a level shift of DC signal unlike ordinary switching diodes. Do not apply sudden stress, such as rush current, directly to the diode.
I Port P4, P5
Notes on Countermeasures for Noise and Latch-up (7481 Group)
(1) Connect a bypass capacitor (0.1F) across the VCC pin and the VSS pin with the shortest possible wiring, using a relatively thick wire. (2) Connect a bypass capacitor (0.01 F) across the VREF pin and the VSS pin with the shortest possible wiring, using a relatively thick wire. (3) In the oscillation circuit, connect across the XIN and XOUT pins with the shortest possible wiring. Connect the GND and VSS pins of the oscillation circuit with the shortest possible wiring, using a relatively thick wire. (4) In the case of the P33/VPP pin of the built-in programmable ROM version, connect an approximately 5 k resistor to the P33/VPP pin the shortest possible in series.
Fig. 55 Notes on use of ports P4 and P5
Notes on Clamp Diode (7481 Group)
(1) Total input current The current of ports P4 and P5 through the clamp diode can be drawn up to 1.0 mA per port. When a current that cannot be consumed by microcomputer is sent flow to the clamp diode, this may raise the power source pin voltage of the microcomputer. The system power circuit must be designed so that the power source voltage of the microcomputer may be stabilized within the standard values. (2) Maximum input voltage If the input voltage of a signal connected to ports P4 and P5 is beyond VCC + 0.3 V, the input waveform should have a delay exceeding 2 s/V from the moment that this waveform goes over the voltage. For using a CR circuit for delay, calculate a proper delay value by the following expression: dt = dv t 0.6 ! VIN 2 ! 10-6 (s/V)
where VIN = Maximum input voltage amplitude margin and t = C ! R.
58
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37481M4/M8/E8-XXXSP/FP, M37481M2T/M4T/M8T/E8T-XXXSP/FP, M37481E8SS ELECTRICAL CHARACTERISTICS (7481 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85 C (Note 1) unless otherwise specified) Table 14. Electrical characteristics Symbol Parameter "H" output voltage P00 - P07, P10 - P17 "L" output voltage P00 - P07, P10 - P17, P40 - P43, P50 - P53 Hysteresis P00 - P07, (Note 2) P30 - P33, P40 - P43, P50 - P53 Hysteresis P16/SCLK, P14/RXD
_____
Test conditions VCC = 5 V, IOH = -5 mA VCC = 3 V, IOH = -1.5 mA VCC = 5 V, IOL = 10 mA VCC = 3 V, IOL = 3 mA VCC = 5 V VCC = 3 V When used as SCLK, RxD input VCC = 5 V VCC = 3 V VI = VCC without pull-up transistor VI = VCC = 5 V VI = VCC = 3 V VI = VCC when analog input is not selected VI = VCC (XIN at stop) VI = 0 V without pull-up VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V VCC = 5 V VCC = 3 V
Standard values Min. 3 2 2 1 0.5 0.3 0.5 0.3 0.5 0.3 5 3 5 3 5 3 5 3 -5 -3 -0.25 -0.08 -0.5 -0.18 -1.0 -0.35 -5 -3 -5 -3 -5 -3 Typ. Max.
Unit
VOH
V
VOL
V
VT + - VT-
V
VT + - VT-
V
VT + - VT-
Hysteresis RESET "H" input current P00 - P07, P10 - P17 "H" input current P30 - P33, P40 - P43, P50 - P53 "H" input current P20 - P27
_____
V
IIH
A
IIH
A A A
IIH
IIH
"H" input current RESET, XIN
IIL
"L" input current P00 - P07, P10 - P17
transistor VI = 0 V with pull-up transistor (Note 3)
A
mA
IIL
"L" input current P30 - P33, P40 - P43, P50 - P53 "L" input current P20 - P27
_____
VI = 0 V VI = 0 V when analog input is not selected VI = 0 V (XIN at stop)
A
IIL
A A
IIL
"L" input current RESET, XIN
Notes 1 : -40 to 85 C for extended operating temperature range version. 2 : Using P0 for key-on wake-up function. 3 : Can be indicated in resistance value as shown below: When VCC = 5 V: 5 k (min.), 10 k (typ.), 20 k (max.). When VCC = 3 V: 8.6 k (min.), 16.7 k (typ.), 37.5 k (max.).
59
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37481M4/M8/E8-XXXSP/FP, M37481M2T/M4T/M8T/E8T-XXXSP/FP, M37481E8SS
Table 14. Electrical characteristics (cont.) Symbol VRAM Parameter RAM retention voltage Test conditions At clock stop mode In high-speed mode, f(XIN) = 4 MHz, VCC = 5 V A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress A-D conversion not executed A-D conversion in progress VCC = 5 V In high-speed mode, f(XIN) = 4 MHz In wait mode In high-speed mode, f(XIN) = 8 MHz VCC = 3 V VCC = 5 V VCC = 5 V In medium-speed mode, f(XIN) = 4 MHz In medium-speed mode, f(XIN) = 8 MHz In stop mode f(XIN) = 0 VCC = 5 V VCC = 3 V VCC = 5 V Ta = 25 C Ta = 85 C Standard values Min. 2 3.5 4 1.8 2 7 7.5 1.75 2 0.9 1 3.5 3.75 1 0.5 2 0.9 0.45 1.8 0.1 1 7 8 3.6 4 14 15 3.5 4 1.8 2 7 7.5 2 1 4 1.8 0.9 3.6 1 10 mA mA Typ. Max. Unit V mA mA mA mA mA mA mA mA mA mA mA mA
In high-speed mode, f(XIN) = 4 MHz, VCC = 3 V
In operating mode ICC Power source current
In high-speed mode, f(XIN) = 8 MHz, VCC = 5 V
In medium-speed mode, f(XIN) = 4 MHz, VCC = 5 V
In medium-speed mode, f(XIN) = 4 MHz, VCC = 3 V
In medium-speed mode, f(XIN) = 8 MHz, VCC = 5 V
A A
60
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37481M4/M8/E8-XXXSP/FP, M37481M2T/M4T/M8T/E8T-XXXSP/FP, M37481E8SS A-D CONVERSION CHARACTERISTICS (7481 Group)
(VCC = 2.7 to 5.5 V, V SS = 0 V, Ta = -20 to 85C (Note) unless otherwise specified) Table 15. A-D conversion characteristics Symbol ---- ---- TCONV Resolution Absolute accuracy (except quantization error) Conversion time VCC = VREF = 5.0 V VCC = 2.7 to 5.5 V, f(XIN) = 4 MHz VCC = 4.5 to 5.5 V, f(XIN) = 8 MHz VCC = 2.7 to 4.0 V VCC = 4.0 to 5.5 V 2 0.5 VCC 12 0 VREF = 5.0 V 50 143 35 Parameter Test conditions Standard values Min. Typ. Max. 8 2 25 12.5 VCC VCC 100 VREF 416 Unit bits LSB
s
VVREF RLADDER VIA IVREF
Reference voltage Ladder resistance Analog input voltage Reference input current
V k V
A
Note: -40 to 85 C for extended operating temperature range version.
61
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MASK ROM CONFIRMATION FORM
GZZ-SH09-84B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480M2T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480M2T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480M2T-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 2FFF16 300016
ROM (4K) codes of the name of the product `M37480M2T-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 6FFF16 700016
ROM (4K) codes of the name of the product `M37480M2T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 EFFF16 F00016
ROM (4K) codes of the name of the product `M37480M2T-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480M2T-' to addresses 000016 to 000F16. ASCII codes `M37480M2T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `M' = 4D16 `2' = 3216
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
62
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-84B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480M2T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command V=
.BYTE
27128 $C000
`M37480M2T-' .BYTE
27256 V= $8000
`M37480M2T-' .BYTE
27512 V= $0000
`M37480M2T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (32P4B for M37480M2T-XXXSP, 32P2W-A for M37480M2T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
63
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-85B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480M4-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480M4-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480M4-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 1FFF16 200016
ROM (8K) codes of the name of the product `M37480M4-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 5FFF16 600016
ROM (8K) codes of the name of the product `M37480M4-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 DFFF16 E00016
ROM (8K) codes of the name of the product `M37480M4-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480M4-' to addresses 000016 to 000F16. ASCII codes `M37480M4-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `M' = 4D16 `4' = 3416
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
64
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-85B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480M4-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command 27128 V= $C000 .BYTE `M37480M4-' 27256 V= $8000 .BYTE `M37480M4-' 27512 V= $0000 .BYTE `M37480M4-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (32P4B for M37480M4-XXXSP, 32P2W-A for M37480M4-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
65
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-86B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480M4T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480M4T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480M4T-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 1FFF16 200016
ROM (8K) codes of the name of the product `M37480M4T-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 5FFF16 600016
ROM (8K) codes of the name of the product `M37480M4T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 DFFF16 E00016
ROM (8K) codes of the name of the product `M37480M4T-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480M4T-' to addresses 000016 to 000F16. ASCII codes `M37480M4T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `M' = 4D16 `4' = 3416
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
66
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-86B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480M4T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command V=
.BYTE
27128 $C000
`M37480M4T-' .BYTE
27256 V= $8000
`M37480M4T-' .BYTE
27512 V= $0000
`M37480M4T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (32P4B for M37480M4T-XXXSP, 32P2W-A for M37480M4T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
67
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-87B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480M8-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480M8-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480M8-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37480M8-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37480M8-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480M8-' to addresses 000016 to 000F16. ASCII codes `M37480M8-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `M' = 4D16 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
68
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-87B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480M8-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37480M8-' 27512 V= $0000 .BYTE `M37480M8-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (32P4B for M37480M8-XXXSP, 32P2W-A for M37480M8-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
69
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-88B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480M8T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480M8T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480M8T-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37480M8T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37480M8T-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480M8T-' to addresses 000016 to 000F16. ASCII codes `M37480M8T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `M' = 4D16 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
70
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-88B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480M8T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command
.BYTE
27256 V= $8000
`M37480M8T-'
27512 V=
.BYTE
$0000
`M37480M8T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (32P4B for M37480M8T-XXXSP, 32P2W-A for M37480M8T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
71
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-78B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481M2T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481M2T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481M2T-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 2FFF16 300016
ROM (4K) codes of the name of the product `M37481M2T-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 6FFF16 700016
ROM (4K) codes of the name of the product `M37481M2T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 EFFF16 F00016
ROM (4K) codes of the name of the product `M37481M2T-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481M2T-' to addresses 000016 to 000F16. ASCII codes `M37481M2T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `M' = 4D16 `2' = 3216
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
72
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-78B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481M2T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command V=
.BYTE
27128 $C000
`M37481M2T-' .BYTE
27256 V= $8000
`M37481M2T-' .BYTE
27512 V= $0000
`M37481M2T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (42P4B for M37481M2T-XXXSP, 44P6N-A for M37481M2T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
73
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-79B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481M4-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481M4-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481M4-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 1FFF16 200016
ROM (8K) codes of the name of the product `M37481M4-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 5FFF16 600016
ROM (8K) codes of the name of the product `M37481M4-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 DFFF16 E00016
ROM (8K) codes of the name of the product `M37481M4-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481M4-' to addresses 000016 to 000F16. ASCII codes `M37481M4-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `M' = 4D16 `4' = 3416
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
74
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-79B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481M4-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command 27128 V= $C000 .BYTE `M37481M4-' 27256 V= $8000 .BYTE `M37481M4-' 27512 V= $0000 .BYTE `M37481M4-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (42P4B for M37481M4-XXXSP, 44P6N-A for M37481M4-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
75
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-80B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481M4T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481M4T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481M4T-XXXFP (hexadecimal notation)
27128
EPROM address 000016 Area for ASCII 000F16 001016 1FFF16 200016
ROM (8K) codes of the name of the product `M37481M4T-'
27256
EPROM address 000016 Area for ASCII 000F16 001016 5FFF16 600016
ROM (8K) codes of the name of the product `M37481M4T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 DFFF16 E00016
ROM (8K) codes of the name of the product `M37481M4T-'
3FFF16
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481M4T-' to addresses 000016 to 000F16. ASCII codes `M37481M4T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `M' = 4D16 `4' = 3416
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
76
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-80B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481M4T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the start address of the assembler source program. EPROM type The pseudo-command V=
.BYTE
27128 $C000
`M37481M4T-' .BYTE
27256 V= $8000
`M37481M4T-' .BYTE
27512 V= $0000
`M37481M4T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (42P4B for M37481M4T-XXXSP, 44P6N-A for M37481M4T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
77
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-81B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481M8-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481M8-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481M8-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37481M8-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37481M8-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481M8-' to addresses 000016 to 000F16. ASCII codes `M37481M8-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `M' = 4D16 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
78
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-81B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481M8-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37481M8-' 27512 V= $0000 .BYTE `M37481M8-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (42P4B for M37481M8-XXXSP, 44P6N-A for M37481M8-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
79
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-82B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481M8T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce masks based on this data. We shall assume the responsibility for errors only if the mask ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481M8T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481M8T-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37481M8T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37481M8T-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481M8T-' to addresses 000016 to 000F16. ASCII codes `M37481M8T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `M' = 4D16 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
80
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-82B<56A0>
Mask ROM number
740 FAMILY MASK ROM CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481M8T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37481M8T-' 27512 V= $0000 .BYTE `M37481M8T-'
Note : If the name of the product written to the EPROMs does not match the name of the mask confirmation, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered fill out the appropriate mark specification form (42P4B for M37481M8T-XXXSP, 44P6N-A for M37481M8T-XXXFP) and attach to the mask ROM confirmation form.
g 3. Comments
81
MITSUBISHI MICROCOMPUTERS
. . nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric ic Not e par Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
ROM PROGRAMMING CONFIRMATION FORM
GZZ-SH09-91B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480E8-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480E8-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480E8-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37480E8-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37480E8-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480E8-' to addresses 000016 to 000F16. ASCII codes `M37480E8-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `E' = 4516 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
82
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-91B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480E8-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37480E8-' 27512 V= $0000 .BYTE `M37480E8-'
Note : If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Please submit the shrink DIP package Mark Specification Form (only for built-in One Time PROM microcomputer) for the M37480E8-XXXSP or the 32P2W-A Mark Specification Form for the M37480E8-XXXFP.
g 3. Comments
83
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-92B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37480E8T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37480E8T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37480E8T-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37480E8T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37480E8T-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37480E8T-' to addresses 000016 to 000F16. ASCII codes `M37480E8T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `0' = 3016 `E' = 4516 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
84
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-92B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37480E8T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command
.BYTE
27256 V= $8000
`M37480E8T-'
27512 V=
.BYTE
$0000
`M37480E8T-'
Note : If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Please submit the shrink DIP package Mark Specification Form (only for built-in One Time PROM microcomputer) for the M37480E8T-XXXSP or the 32P2W-A Mark Specification Form for the M37480E8T-XXXFP.
g 3. Comments
85
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-89B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481E8-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481E8-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481E8-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37481E8-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37481E8-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481E8-' to addresses 000016 to 000F16. ASCII codes `M37481E8-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `E' = 4516 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16 FF16
86
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-89B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481E8-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37481E8-' 27512 V= $0000 .BYTE `M37481E8-'
Note : If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Please submit the shrink DIP package Mark Specification Form (only for built-in One Time PROM microcomputer) for the M37481E8-XXXSP or the 44P6N-A Mark Specification Form for the M37481E8-XXXFP.
g 3. Comments
87
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-90B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM MITSUBISHI ELECTRIC
Receipt
SINGLE-CHIP MICROCOMPUTER M37481E8T-XXXSP/FP
Date: Section head Supervisor signature signature
Note : Please fill in all items marked g. ) Issuance signature Company name Date issued Date: TEL ( Submitted by Supervisor
g Customer
g 1. Confirmation Specify the name of the product being ordered and the type of EPROMs submitted. Three EPROMs are required for each pattern (Check @ in the appropriate box). If at least two of the three sets of EPROMs submitted contain identical data, we will produce ROM programming based on this data. We shall assume the responsibility for errors only if the ROM data on the products we produce differs from this data. Thus, extreme care must be taken to verify the data in the submitted EPROMs. Microcomputer name : M37481E8T-XXXSP Checksum code for entire EPROM EPROM type (indicate the type used) M37481E8T-XXXFP (hexadecimal notation)
27256
EPROM address 000016 Area for ASCII 000F16 001016 3FFF16 400016
ROM (16K) codes of the name of the product `M37481E8T-'
27512
EPROM address 000016 Area for ASCII 000F16 001016 BFFF16 C00016
ROM (16K) codes of the name of the product `M37481E8T-'
7FFF16
FFFF16
(1) Set "FF16" in the shaded area. (2) Write the ASCII codes that indicates the name of the product `M37481E8T-' to addresses 000016 to 000F16. ASCII codes `M37481E8T-' are listed on the right. The addresses and data are in hexadecimal notation.
Address 000016 000116 000216 000316 000416 000516 000616 000716
`M' = 4D16 `3' = 3316 `7' = 3716 `4' = 3416 `8' = 3816 `1' = 3116 `E' = 4516 `8' = 3816
Address 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16
` T ' = 5416 ` - ' = 2D16 FF16 FF16 FF16 FF16 FF16 FF16
88
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
GZZ-SH09-90B<56A0>
ROM number
740 FAMILY ROM PROGRAMMING CONFIRMATION FORM SINGLE-CHIP MICROCOMPUTER M37481E8T-XXXSP/FP MITSUBISHI ELECTRIC
Recommend to writing the following pseudo-command to the assembler source file : EPROM type The pseudo-command 27256 V= $8000 .BYTE `M37481E8T-' 27512 V= $0000 .BYTE `M37481E8T-'
Note : If the name of the product written to the EPROMs does not match the name of the ROM programming confirmation form, the ROM processing is disabled. Write the data correctly.
g 2. Mark specification Mark specification must be submitted using the correct form for the package being ordered. Please submit the shrink DIP package Mark Specification Form (only for built-in One Time PROM microcomputer) for the M37481E8T-XXXSP or the 44P6N-A Mark Specification Form for the M37481E8T-XXXFP.
g 3. Comments
89
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
PACKAGE OUTLINE
32P2W-A
32P4B
90
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
42P4B
44P6N-A
91
PRE
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
L
A IMIN
RY
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MARK SPECIFICATION FORM
32P4B (32-PIN SHRINK DIP) MARK SPECIFICATION FORM
92
PRE
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
L
A IMIN
RY
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
32P2W (32-PIN SOP) MARK SPECIFICATION FORM
93
PRE
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
L
A IMIN
RY
MITSUBISHI MICROCOMPUTERS
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
42P4B (42-PIN SHRINK DIP) MARK SPECIFICATION FORM
94
MITSUBISHI MICROCOMPUTERS
ge. ion. icat to chan ecif l sp ubject fina s ot a its are is n m This etric li m ice: Not e para Som
PRE
L
A IMIN
RY
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
44P6N (44-PIN QFP) MARK SPECIFICATION FORM
Mitsubishi IC catalog name Please choose one of the marking types below (A, B, C), and enter the Mitsubishi IC catalog name and the special mark (if needed). A. Standard Mitsubishi Mark
#3
@3 @2
Mitsubishi lot number (6-digit)
#4
Mitsubishi IC catalog name
$4 q !1
!2
B. Customer's Parts Number + Mitsubishi Catalog Name
#3 #4 @3 @2
Customer's parts number Note : The fonts and size of characters are standard Mitsubishi type. Mitsubishi IC catalog name and Mitsubishi lot number Note4 : If the Mitsubishi logo is not required, check the box below. Mitsubishi logo is not required.
$4 q !1
!2
Note1 : The mark field should be written right aligned. 2 : The fonts and size of characters are standard Mitsubishi type. 3 : Customer's parts number can be up to 7 characters : Only 0 ~ 9, A ~ Z,+,-, , (, ), &, (c), * (period), and (comma) are usable.
,
C. Special Mark Required
#3 #4 @3 @2
$4 q !1
!2
Note1 : If the special mark is to be printed, indicate the desired layout of the mark in the left figure. The layout will be duplicated as close as possible. Mitsubishi lot number (6-digit ) and mask ROM number (3-digit) are always marked. 2 : If the customer's trade mark logo must be used in the special mark, check the box below. Please submit a clean original of the logo. For the new special character fonts a clean font original (ideally logo drawing) must be submitted. Special logo required
3 : The standard Mitsubishi font is used for all characters except for a logo.
95
MITSUBISHI MICROCOMPUTERS
. nge tion ifica t to cha pec al s subjec fin re a ot a is n limits his e: T ametric otic par N e Som
PRE
L
A IMIN
RY
.
7480/7481 GROUP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Keep safety first in your circuit designs!
* Mitsubishi Electric Corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of non-flammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
* * * These materials are intended as a reference to assist our customers in the selection of the Mitsubishi semiconductor product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Mitsubishi Electric Corporation or a third party. Mitsubishi Electric Corporation assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts or circuit application examples contained in these materials. All information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by Mitsubishi Electric Corporation without notice due to product improvements or other reasons. It is therefore recommended that customers contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for the latest product information before purchasing a product listed herein. Mitsubishi Electric Corporation semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. The prior written approval of Mitsubishi Electric Corporation is necessary to reprint or reproduce in whole or in part these materials. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. Please contact Mitsubishi Electric Corporation or an authorized Mitsubishi Semiconductor product distributor for further details on these materials or the products contained therein.
*
* *
*
(c) 1997 MITSUBISHI ELECTRIC CORP. KI-9711 Printed in Japan (ROD) II New publication, effective Nov. 1997. Specifications subject to change without notice.
REVISION DESCRIPTION LIST
Rev. No. 1.0 First Edition
7480/7481 GROUP DATA SHEET
Revision Description Rev. date 971130
(1/1)

▲Up To Search▲

Price & Availability of M37480E8-XXXFP

	To Download M37480E8-XXXFP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .