 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MPE-150S Series Si l O Single Output, 150W 0 Compact, Enclosed AC/DC Power Supplies Electrical Specifications Key Features: * 150W Output Power * Selectable 88-264 AC Input * EN 60950 Compliant * Eight Single Output Models * Meets EN55022 * >285 kHour MTBF * Compact Metal Enclosure Specifications typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Parameter Input Voltage Range Input Frequency Input Current Inrush Current Safety Ground Leakage Current Conditions Min. Typ. 88 115 176 220 248 47 See Model Selection Guide Cold Start, 115 VAC 17.0 Cold Start, 230 VAC 35.0 115 VAC 230 VAC Switch Selectable Max. 132 264 370 63 Units VAC VDC Hz A Pk 1.5 3.5 Max. mA Units Output Parameter Output Voltage Output Current Output Voltage Adjustment Output Voltage Tolerance, See Note 1 Ripple & Noise (20 MHz), See Note 2 Hold-Up Time Set-Up Time Rise Time Temperature Coefficient Short Circuit Protection Over Voltage Protection Overload Protection Conditions Min. Typ. See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide See Model Selection Guide 115 VAC 20 230 VAC 28 230 VAC 100 230 VAC 50 0.02 Continuous (Autorecovery) See Note 3 115 See Note 4 110 Conditions Input to Output Input to Ground Output to Ground 500 VDC Conducted Electrostatic Discharge (ESD) RF Field Susceptibility Electrical Fast Transients/Bursts On Mains Surge Min. 3,000 1,500 500 Typ. RoHS Compliant mSec mSec mSec %/C 135 160 Max. Units VAC General Parameter Isolation Voltage Isolation resistance EMI/RFI EMC Compliance Switching Frequency MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: sales@micropowerdirect.com W: www.micropowerdirect.com 100 M EN 55022; EN 61000-3-2, -3 IEC/EN 61000-4-2, -6, -8, -11 IEC/EN61000-4-3 IEC/EN 61000-4-4 IEC/EN 61000-4-5 25 kHz Units C C % Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Min. Typ. Max. -10 +25 +60 -20 +85 Free Air Convection (See Derating Curve) RH, Non-condensing 95 Ambient Physical Case Size Case Material Weight 7.83 x 4.33 x 1.97 Inches (199.0 x 110.0 x 50.0 mm) Vented Metal Enclosure 28.3 Oz (0.8 kg) Conditions Min. Typ. Max. Units MIL HDBK 217F, 25C, Gnd Benign 285 kHours IEN 60950, IEC 60950 10~500 Hz, 2G 10 min/1 Cycle. Period of 60 min each along X, Y &Z Axis Reliability Specifications Parameter MTBF Safety Standards Vibration Model Selection Guide Model Number MPE-150S-05 MPE-150S-09 MPE-150S-12 MPE-150S-13.5 MPE-150S-15 MPE-150S-24 MPE-150S-27 MPE-150S-48 Input Current (A) 115 VAC 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 230 VAC 1.6 1.6 1.6 1.6 1.6 1.6 1.6 1.6 Output Voltage (VDC) Rated 5.0 9.0 12.0 13.5 15.0 24.0 27.0 48.0 Adjust 4.5 - 5.5 8.0 - 10.4 10.6 - 13.2 12.0 - 15.0 13.5 - 16.5 21.0 - 28.0 24.0 - 30.0 43.0 - 53.0 Current (A) Rated 30.0 16.7 12.5 11.2 10.0 6.5 5.6 3.2 Range 0 to 30.0 0 to 16.7 0 to 12.5 0 to 11.2 0 to 10.0 0 to 6.5 0 to 5.6 0 to 3.2 Output Tolerance (%) 2.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 Ripple & Noise (mV p-p) Efficiency (%, Typ) 150 180 180 180 180 240 240 240 78 80 82 83 84 85 86 87 Notes: 1. Output voltage tolerance includes the the effects of set point accuracy, line regulation and load regulation. 2. Ripple and noise is measured at 20 MHz bandwidth using a 12 inch twisted pair wire to connect to the power supply terminals. A 0.1 F and a 47 F capacitor are connected in parallel as close to the power supply terminals as possible. 3. The overvoltage protection circuit shuts down the output. The unit must be repowered to recover once the fault condition is removed. 4. The overload protection circuit shuts down the output. The unit must be repowered to recover once the fault condition is removed. 5. Efficiency is measured with a 115 VAC input. 6. It is recommended that a fuse be used on the input of a power supply for protection. For the MPE-150S series, a 7.5A/250 VAC slow blow should be used. Mechanical Dimensions Pin Connections Pin 1 2 3 4 5 6 7 Function AC-Line AC-Neutral AC-Ground -Vout -Vout +Vout +Vout Notes: * All dimensions are typical in inches (mm) * Tolerance x.xx = 0.01 (0.25) Derating Curve Static Characteristics (24 Vout) MicroPower Direct www.micropowerdirect.com * 292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 * FAX: (781) 344-8481 * E-Mail: sales@micropowerdirect.com |
Price & Availability of MPE-150S-05
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |