View OM1915NTM_4919619.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

OM1905STM OM1912STM OM1915STM OM1905NTM OM1912NTM OM1915NTM
ISOLATED HERMETIC FIXED VOLTAGE NEGATIVE REGULATORS APPROVED TO DESC DRAWINGS
Three Terminal, Fixed Voltage, 1.5 Amp Precision Negative Regulators In Hermetic JEDEC TO-257AA Package FEATURES
* * * * * * * Isolated Hermetic Package, JEDEC TO-257AA Outline Output Voltages: -5V, -12V, -15V Output Voltages Set Internally to 1% Built-In Thermal Overload Protection Short Circuit Current Limiting Product Is Also Available In Non-Isolated Package Similar To Industry Standards 7905, 7912, 7915
DESCRIPTION
These three terminal negative regulators are supplied in a hermetically sealed metall package whose outline is similar to the industry standard TO-220 plastic package. All protective features are designed into the circuit, including thermal shutdown, current limiting and safe-area control. With heat sinking, they can deliver over 1.5 amps of output current. These units feature internally trimmed output voltages to 1% of nominal voltage. Standard voltages are -5V, -12V, -15V. These units are ideally suited for Military applications where a hermetically sealed package is required.
PART NUMBER DESIGNATOR
Standard Military Drawing Number Omnirel Part Number 5962-8874601 UX OM1905STM 5962-8874601 TX OM1905NTM 5962-8874701 UX OM1912STM 5962-8874701 TX OM1912NTM 5962-8874801 UX OM1915STM 5962-8874801 TX OM1915NTM "U" = Isolated "T" = Non-Isolated
3.3
4 11 R2 Supersedes 1 07 R1
3.3 - 93
OM1905STM/NTM - OM1915STM/NTM
ABSOLUTE MAXIMUM RATINGS @ 25C
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -35 V Operating Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .- 55C to + 150C Storage Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to + 150C Typical Power/Thermal Charateristics: Rated Power @ 25 C TC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15W TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3W Thermal Resistance qJC (Case U) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2C/W qJC (Case T) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5C/W aa qJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42C/W ELECTRICAL CHARACTERISTICS -5 Volt
Parameter Output Voltage Symbol VOUT VIN = -10V, Io = 500mA, -55C TA 125C (unless otherwise specified) Min. -4.95 Max. -5.05 -5.15 Unit V V
Test Conditions TA = 25C VIN = -7.5V to -20V IO = 5mA to 1.0, A, P < 15W
*
-4.85
Line Regulation (Note 1) (Note 4)
VRLINE
VIN = -7.5V to -20V
12
mV mV mV mV mV mV mV mV mA mA mA
*
VIN = -8.0V to -12V
25 5
*
Load Regulation (Note 1) IO = 250mA to 750 mA VRLOAD IO = 5mA to 1.5 Amp
12 20
* *
25 15 30 2.5
Standby Current Drain
ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT NO DVOUT Dt DVOUT = 100mV, IO = 1.0A TA = 25C VIN = -35V IO = 5mA to 1000mA VIN = -7.0V to -20V
Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2)
* * * *
1.5
3.0 0.4
0.4
mA
2.5 3.3 1.2
V A A A dB dB
*
f =120 Hz, DVIN = -10V (Note 3) TA = 25C, f =10 Hz to 100KHz TA = 25C, t = 1000 hrs. 63
2.8
3.3
Ripple Rejection
*
60 40
Output Noise Voltage (Note 3) Long Term Stability (Note 3)
V/V RMS
75
mV
Notes: 1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range.
3.3 - 94
OM1905STM/NTM - OM1915NTM/STM ELECTRICAL CHARACTERISTICS -12 Volt
Parameter Output Voltage Symbol VOUT VIN = -19V, Io = 500mA, -55C TA 125C (unless otherwise specified) Min. -11.88 Max. -12.12 -12.36 Unit V V Test Conditions TA = 25C VIN = -14.5V to -27V IO = 5mA to 1.0 A, P < 15W Line Regulation (Note 1) (Note 4) VIN = -16V to -22V VRLINE VIN = -14.5V to -27V 20 mV mV mV mV mV mV mV mV mA mA mA
*
-11.64
* *
50 10 30 32
Load Regulation (Note 1)
VRLOAD
IO = 5mA to 1.5 Amp
*
IO = 250mA to 750 mA
60 16
*
Standby Current Drain ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT Output Noise Voltage (Note 3) Long Term Stability (Note 3) DVOUT Dt TA = 25C, t = 1000 hrs. NO DVOUT = 100mV, IO = 1.0A TA = 25C, IO = 5mA to 1A VIN = -35V IO = 5mA to 1000mA VIN = -14.5V to -27V
30 3.5
Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection
* * * *
1.5
4.0 0.8
0.5
mA
1.8 3.3 1.2
V A A A dB dB
*
f =120 Hz, DVIN = -10V (Note 3) TA = 25C, f =10 Hz to 100KHz 56
2.8
*
53 40
V/V RMS
120
mV
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range. 4. Minimum load current for full line regulation = 5 mA.
MECHANICAL OUTLINE
.420 .410 .200 .190 .045 .035 .665 .645 .537 .527 .430 .410 .038 MAX.
CONNECTION DIAGRAM
3.3
4
.150 .140
.750 .500
.005
Case U 1 Ground 2 Input 3 Output 4 No Connection
1 2 3
Case T 1 Ground 2 Input 3 Output 4 Input
.035 .025
.100 TYP.
.120 TYP.
3.3 - 95
OM1905STM/NTM - OM1915STM/NTM ELECTRICAL CHARACTERISTICS -15 Volt
Parameter Output Voltage Symbol VOUT
VIN = -23V, Io = 500mA, -55C TA 125C (unless otherwise specified) Min. -14.85 Max. -15.15 -15.45 Unit V V
Test Conditions TA = 25C VIN = -17.5V to -30V IO = 5mA to 1.0 A, P < 15 W
*
-14.55
Line Regulation (Note 1) (Note 4)
VRLINE
VIN = -17.5V to -30V
25
mV mV mV mV mV mV mV mV mA mA mA
*
VIN = -20V to -26V
50 15
*
Load Regulation (Note 1) IO = 250mA to 750 mA VRLOAD IO = 5mA to 1.5 Amp
25 35
* *
75 21 45 6.0
Standby Current Drain
ISCD DISCD (Line) DISCD (Load) VDO IO (pk) IDS DVIN DVOUT NO DVOUT Dt DVOUT = 100mV, IO = 1.0A TA = 25C VIN = -35V IO = 5mA to 1000 mA VIN = -17.5V to -30V
Standby Current Drain Change With Line Standby Current Drain Change With Load Dropout Voltage Peak Output Current Short Circuit Current (Note 2) Ripple Rejection
* * * *
1.5
6.5 0.8
0.5
mA
2.5 3.3 1.2
V A A A dB dB
*
f =120 Hz, DVIN = -10V (Note 3) TA = 25C, f =10 Hz to 100KHz TA = 25C, t = 1000 hrs. 53
2.8
*
50 40
Output Noise Voltage (Note 3) Long Term Stability (Note 3)
V/V RMS
150
mV
Notes:
1. Load and Line Regulation are specified at a constant junction temperature. Pulse testing with low duty cycle is used. Changes in output voltage due to heating effects must be taken into account separately. 2. Short Circuit protection is only assured up to VIN = -35V. 3. If not tested, shall be guaranteed to the specified limits. The * denotes the specifications which apply over the full operating temperature range.
TYPICAL PERFORMANCE CHARACTERISTICS
PEAK OUTPUT
3.3
3.5 3
Tj = -55C
DROPOUT VOLTAGE
2.5 100
RIPPLE REJECTION
2
Output Current (A)
Output Current (A)
2.5 2
Tj = 25C
1.5
IOUT = 500mA
Ripple Rejection (dB)
IOUT = 1A
80
VOUT = 5V
60
1.5 1
Tj = 150C
1
IOUT = 0A
40
VIN - V = 8VDC +3.5Vrms IOUT = 1A Tj = 25C
0.5
DVOUT = 100MV
0.5
DVOUT = 100mV
20
0 0 5 10 15 20 25 30 35
0 -75 -50 -25
0
25 50 75 100 125 150
0 10 100 1k 10k 100k
Input To Output Differential (V)
Junction Temperature (C)
Frequency (Hz)
205 Crawford Street, Leominster, MA 01453 USA (508) 534-5776 FAX (508) 537-4246

▲Up To Search▲

Price & Availability of OM1915NTM

	To Download OM1915NTM Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .