 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MIL-PRF (CWR Style) Established Reliability T492 CWR11 Style Mil-PRF-55365/8 Overview The KEMET T492 series is approved to MIL-PRF-55365/8 (CWR11) with Weibull failure rates of B level (0.1% failures per 1000 hours), C level (0.01% failures per 1000 hours), or D level (0.001% failures per 1000 hours). This CWR11 product is a precision-molded device, with compliant terminations and indelible laser marking. This is the military version of the global IEC/EIA standard represented by KEMET's T491 Series. Tape and reeling per EIA 481-1 is standard. Benefits * * * * * * * * * * Established reliability options Taped and reeled per EIA 481-1 Symmetrical, compliant terminations Laser-marked case 100% surge current test available on all case sizes Qualified to MIL-PRF-55365/8, Style CWR11 Termination options B, C, H, K Weibull failure options B, C, and D Voltage rating of 4-50 VDC Operating temperature range of -55C to +125C Applications Typical applications include decoupling and filtering in military and aerospace applications requiring CWR11 devices. Environmental Compliance *When ordered with 100% Sn Solder RoHS Compliant (6/6)* according to Directive 2002/95/EC SPICE For a detailed analysis of specific part numbers, please visit kemet.com for a free download of KEMET's SPICE software. The KEMET SPICE program is freeware intended to aid design engineers in analyzing the performance of these capacitors over frequency, temperature, ripple, and DC bias conditions. One WORLD One Brand One Strategy One Focus One Team One KEMET T2006-1 * 10/11/2010 1 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Ordering Information T Capacitor Class 492 Series D Case Size 156 Capacitance Code (pF) K Capacitance Tolerance J = 5% K = 10% M = 20% 020 Voltage 006 = 6.3V 010 = 10V 015 = 15V 020 = 20V 025 = 25V 035 = 35V 050 = 50V A Failure Rate/Design C Lead Material 4251 Surge (C-Spec) 4250= 25C after Weibull 4251 = -55C and 85C after Weibull 4252 = -55C and 85C before Weibull T= CWR 11 Tantalum Established Reliability A = 3216-18 First two digits B = 3258-19 represent significant C = 6032-25 figures. Third digit D = 7343-31 specifies number of zeros. A = N/A C = Hot Solder Dipped B = 0.1%/1000 hrs H = Standard Solder C = .01%/1000 hrs Coated (SnPb 5% Pb D = .001%/1000 hrs minimum) B = Gold Plated K = Solder Fused *See www.kemet.com for Pb Free transition. Performance Characteristics Item Operating Temperature Rated Capacitance Range Capacitance Tolerance Rated Voltage Range DF(120Hz) ESR (100kHz) Leakage Current -55C to 125C 0.1F - 100F @ 120 Hz/25C J Tolerance (5%), K Tolerance (10%), M Tolerance (20%) 4V - 50V Refer to Part Number Electrical Specification Table Refer to Part Number Electrical Specification Table 0.01CV (A) at Rated Voltage after 5 minutes Performance Characteristics (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 2 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Qualification Test Endurance Condition C/C 85C @ Rated Voltage, 2000 Hrs. 125C @ 2/3 Rated Voltage, 2000 Hrs. DF DCL ESR C/C DF DCL ESR C/C Mil-Std-202, Method 107, Condition B, mounted, -55C to 125C, 1000 cycles DF DCL ESR Extreme temperature exposure at a succession of continuous steps at +25C, -55C, +25C, +85C, +125C, +25C. +25C C/C DF DCL IL* IL IL C/C DF DCL ESR C/C DF DCL Characteristics Within 10% of initial value Within initial limits Within 1.25 x initial limit Within initial limits Within 10% of initial value Within initial limits Within 1.25 x initial limit Within initial limits Within 5% of initial value Within initial limits Within 1.25 x initial limit Within initial limits -55C 10% IL n/a +85C 10% 1.5 x IL 10 x IL +125C 20% 1.5 x IL 12 x IL Storage Life 125C @ 0 Volts, 2000 Hrs. Thermal Shock Temperature Stability Within 5% of initial value Within initial limits Within initial limits Within initial limits Within 10 of initial value Within initial limits Within initial limits Surge Voltage 25C and 85 C, 1.32 x Rated Voltage 1000 cycles (125C, 1.2 x Rated Voltage) Mechanical Shock/Vibration Additional qualification tests per MIL-PRF-55365/8 *IL = Initial Limit Mil-Std-202, Meth. 213, Cond. I, 100G Peak Mil-Std-202, Meth. 204, Cond. D, 10Hz to 2000Hz, 20G Peak Certification Mil-PRF-55365/8 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 3 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Electrical Characteristics ESR vs. Frequency 1000 T492B225/020_IMP T492C685/020_IMP Capacitance vs. Frequency 100 T492B225/020 T492C685/020 T492D156/020 100 T492D156/020_IMP T492B225/020_ESR T492C685/020_ESR T492D156/020_ESR 10 Impedance, ESR (Ohms) Capacitance (F) 1,000,000 10,000,000 10 1 1 0.1 0.1 100 1,000 10,000 Frequency (Hz) 100,000 0.01 100 1,000 10,000 Frequency (Hz) 100,000 1,000,000 10,000,000 Dimensions - Millimeters (Inches) Metric will govern Termination cutout at KEMET's Option, either end Case Size KEMET A B C D EIA 3216-18 3528-21 6032-28 7343-31 Component L* 3.2 0.2 (.126 .008) 3.5 02 (138 .008) 6.0 0.3 (.236 .03) 7.3 0.3 (287 .012) W* 1.6 0.2 (.063 .008) 2.8 0.2 (.110 .008) 3.2 0.3 (.126 .012) 4.3 0.3 (.169 .012) H* 1.6 0.2 (.063 .008) 1.9 0.2 (.075 .008) 2.5 0.3 (.098 .012) 2.8 0.3 (098 .012) F* 0.1 S* 0.3 B* 0.15 (.004) (.012) (Ref) .006 1.2 (.047) 2.2 (.087) 2.2 (.087) 2.4 (.094) 0.8 (.031) 0.8 (.031) 1.3 (.051) 1.3 (.051) 0.4 (.016) 0.4 (.016) 0.5 (.020) 0.5 (.020) X (Ref) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) 0.10 0.10 (.004 .004) P (Ref) 0.4 (.016) 0.5 (.020) 0.9 (.035) 0.9 (.035) R (Ref) 0.4 (.016) 1.0 (.039) 1.0 (.039) 1.0 (.039) T (Ref) A (Min) G (Ref) E (Ref) 1.1 (.043) 1.3 (.051) 1.8 (.071) 2.2 (.087) 0.13 (.005) 1.4 (.055) 0.13 (.005) 2.1 (.083) 0.13 (.005) 3.1 ( (.122) 2.8 (.110) 2.4 (.094) 0.13 (.005) 3.8 (.150) 3.5 (.138) 3.5 (.138) Notes: (Ref) - Dimensions provided for reference only. No dimensions provided for B, P or R because low profile cases do not have a bevel or a notch. * MIL-C-55365/8 specified dimensions (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 4 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Table 1 - Ratings & Part Number Reference Rated Voltage 105C VDC 4 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 10 10 10 15 15 15 15 15 15 15 15 15 20 20 20 20 20 20 20 20 20 20 Rated Cap 120Hz F 2.2 4.7 6.8 10 15 33 68 100 1.5 2.2 3.3 4.7 6.8 10 15 22 47 68 1 1.5 2.2 3.3 4.7 6.8 15 33 47 0.68 1 1.5 2.2 3.3 4.7 10 22 33 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 15 22 Case Code/ Case Size KEMET/EIA A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 D/7343-31 D/7343-31 A/3216-18 A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 C/6032-28 D/7343-31 D/7343-31 A/3216-18 A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 D/7343-31 D/7343-31 A/3216-18 A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 D/7343-31 D/7343-31 A/3216-18 A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 C/6032-28 D/7343-31 D/7343-31 KEMET Part Number (See below for part options) T492A225(1)004(2)(3)(4) T492A475(1)004(2)(3)(4) T492B685(1)004(2)(3)(4) T492B106(1)004(2)(3)(4) T492B156(1)004(2)(3)(4) T492C336(1)004(2)(3)(4) T492D686(1)004(2)(3)(4) T492D107(1)004(2)(3)(4) T492A155(1)006(2)(3)(4) T492A225(1)006(2)(3)(4) T492A335(1)006(2)(3)(4) T492B475(1)006(2)(3)(4) T492B685(1)006(2)(3)(4) T492B106(1)006(2)(3)(4) T492C156(1)006(2)(3)(4) T492C226(1)006(2)(3)(4) T492D476(1)006(2)(3)(4) T492D686(1)006(2)(3)(4) T492A105(1)010(2)(3)(4) T492A155(1)010(2)(3)(4) T492A225(1)010(2)(3)(4) T492B335(1)010(2)(3)(4) T492B475(1)010(2)(3)(4) T492B685(1)010(2)(3)(4) T492C156(1)010(2)(3)(4) T492D336(1)010(2)(3)(4) T492D476(1)010(2)(3)(4) T492A684(1)015(2)(3)(4) T492A105(1)015(2)(3)(4) T492A155(1)015(2)(3)(4) T492B225(1)015(2)(3)(4) T492B335(1)015(2)(3)(4) T492B475(1)015(2)(3)(4) T492C106(1)015(2)(3)(4) T492D226(1)015(2)(3)(4) T492D336(1)015(2)(3)(4) T492A474(1)020(2)(3)(4) T492A684(1)020(2)(3)(4) T492A105(1)020(2)(3)(4) T492B155(1)020(2)(3)(4) T492B225(1)020(2)(3)(4) T492B335(1)020(2)(3)(4) T492C475(1)020(2)(3)(4) T492C685(1)020(2)(3)(4) T492D156(1)020(2)(3)(4) T492D226(1)020(2)(3)(4) Mil-C-55365/4F Part Number (See below for part options) CWR11C(6)225(1)(2)(5) CWR11C(6)475(1)(2)(5) CWR11C(6)685(1)(2)(5) CWR11C(6)106(1)(2)(5) CWR11C(6)156(1)(2)(5) CWR11C(6)336(1)(2)(5) CWR11C(6)686(1)(2)(5) CWR11C(6)107(1)(2)(5) CWR11D(6)155(1)(2)(5) CWR11D(6)225(1)(2)(5) CWR11D(6)335(1)(2)(5) CWR11D(6)475(1)(2)(5) CWR11D(6)685(1)(2)(5) CWR11D(6)106(1)(2)(5) CWR11D(6)156(1)(2)(5) CWR11D(6)226(1)(2)(5) CWR11D(6)476(1)(2)(5) CWR11D(6)686(1)(2)(5) CWR11F(6)105(1)(2)(5) CWR11F(6)155(1)(2)(5) CWR11F(6)225(1)(2)(5) CWR11F(6)335(1)(2)(5) CWR11F(6)475(1)(2)(5) CWR11F(6)685(1)(2)(5) CWR11F(6)156(1)(2)(5) CWR11F(6)336(1)(2)(5) CWR11F(6)476(1)(2)(5) CWR11H(6)684(1)(2)(5) CWR11H(6)105(1)(2)(5) CWR11H(6)155(1)(2)(5) CWR11H(6)225(1)(2)(5) CWR11H(6)335(1)(2)(5) CWR11H(6)475(1)(2)(5) CWR11H(6)106(1)(2)(5) CWR11H(6)226(1)(2)(5) CWR11H(1)336(1)(2)(5) CWR11J(6)474(1)(2)(5) CWR11J(6)684(1)(2)(5) CWR11J(6)105(1)(2)(5) CWR11J(6)155(1)(2)(5) CWR11J(6)225(1)(2)(5) CWR11J(6)335(1)(2)(5) CWR11J(6)475(1)(2)(5) CWR11J(6)685(1)(2)(5) CWR11J(6)156(1)(2)(5) CWR11J(6)226(1)(2)(5) DC Leakage +20C Amps 0.1 0.2 0.3 0.4 0.6 1.3 2.7 4.0 0.1 0.1 0.2 0.3 0.4 0.6 0.9 1.4 3.0 4.3 0.1 0.2 0.2 0.3 0.5 0.7 1.5 3.3 4.7 0.1 0.2 0.2 0.3 0.5 0.7 1.5 3.3 5.0 0.1 0.1 0.2 0.3 0.4 0.7 0.9 1.4 3.0 4.4 DF ESR Moisture Sensitivity Temp260C J-STD-020D 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 +20C 120Hz +20C 100kHz % Max mOhms 6.0 8.0 6.0 8.0 6.0 5.5 6.0 4.0 6.0 3.5 6.0 2.2 6.0 1.1 8.0 0.9 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 4.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 4.0 4.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 6.0 8.0 8.0 8.0 5.5 4.5 3.5 3.0 2.2 1.1 0.9 10.0 8.0 8.0 5.5 4.5 3.5 2.5 1.1 0.9 12.0 10.0 8.0 5.5 5.0 4.0 2.5 1.1 0.9 14.0 12.0 10.0 6.0 5.0 4.0 3.0 2.4 1.1 0.9 T 492 D 156 K 020 A C 4251 CWR A = Code/ First two digits J = 5% Mil-C-55365/4F Part 006 = 6.3V A = N/A Rated T = Rated 11 Case 3216-18 DC C = Hot Solder Dipped 4250= 25C after Moisture KEMET Part Number DF Established Case Size represent significant K = 10% B = 3258-19 010 = 10V B = 0.1%/1000 hrs H = Standard Solder ESR Weibull Tantalum Cap Voltage Number Leakage Sensitivity Reliability C = 6032-25 figures. Third digit M = 20% 015 = 15V C = .01%/1000 hrs Coated (SnPb 5% Pb 4251 = -55C and D = 7343-31 specifies number of 020 = 20V D = .001%/1000 hrs minimum) 85C after Weibull Other part number options: zeros. 025 = 25V B = Gold Plated 4252 = -55C and Where the 10th character equal to K (10% tolerance) is also available in M (20% tolerance). 035 = 35V K = Solder Fused 85C before Weibull 050 = 50V Where the 10th character equal to M (20% tolerance) is only available in M (20% tolerance). 25 0.33 Capacitor Series VDC F Class 105C 120Hz A/3216-18 KEMET/EIA Case Size T492A334(1)025(2)(3)(4) CWR11K(6)334(1)(2)(5) 0.1 Capacitance Capacitance Voltage Failure Rate/Design Amps (see below for (see below for Code (pF) Tolerance part options) part options) +20C 4.0 15.0 1.0 Lead Material Surge % Max mOhms (C-Spec) J-STD-020A +20C +20C 100kHz Temp260C Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H) Also available on large (13 inch) reels. Add 7280 to the end of the part number. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 5 Roll Over for Order Info. MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Table 1 - Ratings & Part Number Reference con't Rated Voltage 105C VDC 25 25 25 25 25 25 25 25 25 25 35 35 35 35 35 35 35 35 35 35 35 35 50 50 50 50 50 50 50 50 50 50 50 VDC 105C Rated Cap 120Hz F 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 10 15 0.1 0.15 0.22 0.33 0.47 0.68 1 1.5 2.2 3.3 4.7 6.8 0.1 0.15 0.22 0.33 0.47 0.68 1 1.5 2.2 3.3 4.7 F 120Hz Case Code/ Case Size KEMET/EIA A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 C/6032-28 C/6032-28 D/7343-31 D/7343-31 D/7343-31 A/3216-18 A/3216-18 A/3216-18 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 C/6032-28 C/6032-28 D/7343-31 D/7343-31 A/3216-18 B/3528-20 B/3528-20 B/3528-20 C/6032-28 C/6032-28 C/6032-28 D/7343-31 D/7343-31 D/7343-31 D/7343-31 KEMET/EIA KEMET Part Number (See below for part options) T492A474(1)025(2)(3)(4) T492B684(1)025(2)(3)(4) T492B105(1)025(2)(3)(4) T492B155(1)025(2)(3)(4) T492C225(1)025(2)(3)(4) T492C335(1)025(2)(3)(4) T492C475(1)025(2)(3)(4) T492D685(1)025(2)(3)(4) T492D106(1)025(2)(3)(4) T492D156(1)025(2)(3)(4) T492A104(1)035(2)(3)(4) T492A154(1)035(2)(3)(4) T492A224(1)035(2)(3)(4) T492A334(1)035(2)(3)(4) T492B474(1)035(2)(3)(4) T492B684(1)035(2)(3)(4) T492B105(1)035(2)(3)(4) T492C155(1)035(2)(3)(4) T492C225(1)035(2)(3)(4) T492C335(1)035(2)(3)(4) T492D475(1)035(2)(3)(4) T492D685(1)035(2)(3)(4) T492A104(1)050(2)(3)(4) T492B154(1)050(2)(3)(4) T492B224(1)050(2)(3)(4) T492B334(1)050(2)(3)(4) T492C474(1)050(2)(3)(4) T492C684(1)050(2)(3)(4) T492C105(1)050(2)(3)(4) T492D155(1)050(2)(3)(4) T492D225(1)050(2)(3)(4) T492D335(1)050(2)(3)(4) T492D475(1)050(2)(3)(4) (see below for part options) Mil-C-55365/4F Part Number (See below for part options) CWR11K(6)474(1)(2)(5) CWR11K(6)684(1)(2)(5) CWR11K(6)105(1)(2)(5) CWR11K(6)155(1)(2)(5) CWR11K(6)225(1)(2)(5) CWR11K(6)335(1)(2)(5) CWR11K(6)475(1)(2)(5) CWR11K(6)685(1)(2)(5) CWR11K(6)106(1)(2)(5) CWR11K(6)156(1)(2)(5) CWR11M(6)104(1)(2)(5) CWR11M(6)154(1)(2)(5) CWR11M(6)224(1)(2)(5) CWR11M(6)334(1)(2)(5) CWR11M(6)474(1)(2)(5) CWR11M(6)684(1)(2)(5) CWR11M(6)105(1)(2)(5) CWR11M(6)155(1)(2)(5) CWR11M(6)225(1)(2)(5) CWR11M(6)335(1)(2)(5) CWR11M(6)475(1)(2)(5) CWR11M(6)685(1)(2)(5) CWR11N(6)104(1)(2)(5) CWR11N(6)154(1)(2)(5) CWR11N(6)224(1)(2)(5) CWR11N(6)334(1)(2)(5) CWR11N(6)474(1)(2)(5) CWR11N(6)684(1)(2)(5) CWR11N(6)105(1)(2)(5) CWR11N(6)155(1)(2)(5) CWR11N(6)225(1)(2)(5) CWR11N(6)335(1)(2)(5) CWR11N(6)475(1)(2)(5) (see below for part options) DC Leakage +20C Amps 0.1 0.2 0.3 0.4 0.6 0.8 1.2 1.7 2.5 3.8 0.0 0.1 0.1 0.1 0.2 0.2 0.4 0.5 0.8 1.2 1.6 2.4 0.1 0.1 0.1 0.2 0.2 0.3 0.5 0.8 1.1 1.7 2.4 Amps +20C DF ESR Moisture Sensitivity Temp260C J-STD-020D 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 J-STD-020A Temp260C +20C 120Hz +20C 100kHz % Max mOhms 4.0 14.0 4.0 7.5 4.0 6.5 6.0 6.5 6.0 3.5 6.0 3.5 6.0 2.5 6.0 1.4 6.0 1.2 6.0 1.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 6.0 6.0 6.0 6.0 6.0 6.0 4.0 4.0 4.0 4.0 4.0 4.0 6.0 6.0 6.0 6.0 % Max +20C 24.0 21.0 18.0 15.0 10.0 8.0 6.5 4.5 3.5 2.5 1.5 1.3 22.0 17.0 14.0 12.0 8.0 7.0 6.0 4.0 2.5 2.0 1.5 mOhms +20C 100kHz Rated Voltage Rated Cap Case Code/ Case Size KEMET Part Number Mil-C-55365/4F Part Number DC Leakage DF ESR Moisture Sensitivity T Capacitor Class 492 Series D Case Size 156 Capacitance Code (pF) K Capacitance Tolerance J = 5% K = 10% M = 20% 020 Voltage A Failure Rate/Design C Lead Material 4251 Surge (C-Spec) 4250= 25C after Weibull 4251 = -55C and 85C after Weibull 4252 = -55C and 85C before Weibull 006 = 6.3V 010 = 10V 015 = 15V 020 = 20V Other part number options: 025 = 25V Where the 10th character equal to K (10% tolerance) is also available in M (20% tolerance). 035 = 35V 050 = 50V Where the 10th character equal to M (20% tolerance) is only available in M (20% tolerance). T= CWR 11 Tantalum Established Reliability A = 3216-18 First two digits B = 3258-19 represent significant C = 6032-25 figures. Third digit D = 7343-31 specifies number of zeros. A = N/A C = Hot Solder Dipped B = 0.1%/1000 hrs H = Standard Solder C = .01%/1000 hrs Coated (SnPb 5% Pb D = .001%/1000 hrs minimum) B = Gold Plated K = Solder Fused Standard with tin terminations (14th character = T). Tin/lead terminations is also available (14th character = H) Also available on large (13 inch) reels. Add 7280 to the end of the part number. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 6 Roll Over for Order Info. MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Recommended Voltage Derating Guidelines 120% 100% % Working Voltage 80% 60% 40% 20% 0% % Change in Working DC Voltage with Temperature 67% Recommended Maximum Application Voltage (As % of Rated Voltage) 33% -55 25 Temperature (C) 85 125 Ripple Current/Ripple Voltage Case Code KEMET A B C D X E R S T U V T510X T510E EIA 3216-18 3528-21 6032-28 7343-31 7343-43 7260-38 2012-12 3216-12 3528-12 6032-15 7343-20 7343-43 7260-38 Maximum Power Dissipation (Pmax) mWatts @ 25C w/+20C Rise 75 85 110 150 165 200 25 60 70 90 125 270 285 25C 85C 1.00 0.90 T= Environmental Temperature Temperature Compenstion Multipliers for Maximum Power Dissipation 125C 0.40 Using the P max of the device, the maximum allowable rms ripple current or voltage may be determined. I(max) = P max/R E(max) = P max*R I = rms ripple current (amperes) E = rms ripple voltage (volts) Pmax = maximum power dissipation(watts) R = ESR at specified frequency (ohms) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 7 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Reverse Voltage Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within these limits. Temperature 25 C 85 C 125 C Permissible Transient Reverse Voltage 15% of Rated Voltage 5% of Rated Voltage 1% of Rated Voltage Table 2 - Land Dimensions/Courtyard KEMET Case A B C D Metric Size Code EIA 3216-18 3258-19 6032-25 7343-31 X 1.35 2.35 2.35 2.55 Density Level A: Maximum (Most) Land Protrusion (mm) Y 2.15 2.15 2.65 3.75 C 1.45 1.45 2.60 2.70 V1 6.10 6.10 8.90 10.20 V2 2.80 4.00 4.40 5.50 X 1.25 2.25 2.25 2.45 Density Level B: Median (Nominal) Land Protrusion (mm) Y 1.75 1.75 2.25 3.35 C 1.35 1.35 2.50 2.60 V1 5.00 5.00 7.80 9.10 V2 2.30 3.50 3.90 5.00 X 1.15 2.15 2.15 2.35 Density Level C: Minimum (Least) Land Protrusion (mm) Y 1.35 1.35 1.85 2.95 C 1.25 1.25 2.40 2.50 V1 4.10 4.10 6.90 8.20 V2 2.00 3.20 3.60 4.70 Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reflow solder processes. Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reflow solder processes. Density Level C: For high component desity product applications. Before adapting the minimum land pattern variations the user should perform qualification testing based on the conditions outlined in IPC standard 7351 (IPC-7351). Height of these chips may create problems in wave soldering. Land pattern geometry is too small for silkscreen outline. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 8 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Soldering Process KEMET's families of surface mount tantalum capacitors are compatible with wave (single or dual), convection, IR or vapor phase reflow techniques. Preheating of these components is recommended to avoid extreme thermal stress. KEMET's recommended profile conditions for convection and IR reflow reflect the profile conditions of the IPC/J-STD-020D standard for moisture sensitivety testing. The devices can safely withstand a maximum of three reflow passes at these conditions. Note that although the X/7343-43 case size can withstand wave soldering, the tall profile (4.3mm maximum) dictates care in wave process development. Profile Feature Preheat/Soak Temperature Min (TSmin) Temperature Max (TSmax) Time (ts) from Tsmin to Tsmax) Ramp-up rate (TL to TP) Liquidous temperature (TL) Time above liquidous (tL) Peak Temperature (TP) Time within 5C of max peak temperature (tP) Ramp-down rate (TP to TL) Time 25C to peak temperature 100C 150C 60-120 sec 3C/sec max 183C 60-150 sec 220C* 235C** 20 sec max 6C/sec max 6 minutes max 150C 200C 60-120 sec 3C/sec max 217C 60-150 sec 250C* 260C** 30 sec max 6C/sec max 8 minutes max TP TL Tsmax Tsmin Max Ramp Up Rate = 3 C/sec Max Ramp Down Rate = 6 C/sec tP tL Temperature tS 25 25 C to Peak Time Time/Temperature Soldering Profile Sn-Pb Assembly Pb-Free Assembly Note 1: All temperatures refer to the center of the package, measured on the package body surface that is facing up during assembly reflow. * Case Size D, E, P, Y and X **Case Size A, B, C, H, I, K, M, R, S, T, U, V, W and Z Construction MNO2 /Ta2O5/Ta Silver Paint Silver Adhesive Washer Leadframe (-Cathode) Carbon Tantalum Wire Weld Leadframe (+Anode) (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 9 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Capacitor Marking KEMET CWR 11 Style J 156 25 K 030 * 010 = 30th week of 2010 Polarity Indicator (+) Picofarad Code KEMET ID PWC* Rated Voltage Storage Tantalum chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term storage. In addition, packaging materials will be degraded by high temperature - reels may soften or warp, and tape peel force may increase. KEMET recommends that maximum storage temperature not exceed 40 degrees C, and maximum storage humidity not exceed 60% relative humidity. In addition, temperature fluctuations should be minimized to avoid condensation on the parts, and atmospheres should be free of chlorine and sulphur bearing compounds. For optimized solderability, chip stock should be used promptly, preferably within three years of receipt. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 10 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Tape & Reel Packaging Information KEMET's Molded Tantalum and Aluminum Chip Capacitor families are packaged in 8 mm and 12 mm plastic tape on 7" and 13" reels, in accordance with EIA Standard 481-1: Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape fed automatic pick and place systems. Table 4 - Packaging Quantity Case Code KEMET R I S T M U L W Z V A B C D Y X E EIA 2012-12 3216-10 3216-12 3528-12 3528-15 6032-15 6032-19 7343-15 7343-17 7343-20 3216-18 3528-21 6032-28 7343-31 7343-40 7343-43 7260-38 Tape Width-mm 8 8 8 8 8 12 12 12 12 12 8 8 12 12 12 12 12 7" Reel* 2,500 3,000 2,500 2,500 2,000 1,000 1,000 1,000 1,000 1,000 2,000 2,000 500 500 500 500 500 13" Reel* 10,000 12,000 10,000 10,000 8,000 5,000 5,000 3,000 3,000 3,000 9,000 8,000 3,000 2,500 2,000 2,000 2,000 * No c-spec required for 7" reel packaging. C-7280 required for 13" reel packaging. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 11 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Figure 1 - Embossed (Plastic) Carrier Tape Dimensions T T2 P2 ODo Po [10 pitches cumulative tolerance on tape 0.2 mm] E1 Ao F Ko B1 Bo E2 W S1 T1 Cover Tape B1 is for tape feeder reference only, including draft concentric about B o. Center Lines of Cavity P1 OD1 Embossment For cavity size, see Note 1 Table 5 User Direction of Unreeling Table 5 - Embossed (Plastic) Carrier Tape Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size 8mm 12mm 16mm 1.5 +0.10/-0.0 (0.059 +0.004/-0.0) D0 D1 Min. Note 1 1.0 (0.039) 1.5 (0.059) E1 P0 P2 R Ref. Note 2 25.0 (0.984) 30 (1.181) S1 Min. Note 3 0.600 (0.024) T Max. T1 Max. 1.75 0.10 (0.069 0.004) 4.0 0.10 (0.157 0.004) 2.0 0.05 (0.079 0.002) 0.600 (0.024) 0.100 (0.004) Variable Dimensions -- Millimeters (Inches) Tape Size 8mm 12mm 16mm Pitch Single (4mm) Single (4mm) & Double (8mm) Triple (12mm) B1 Max. Note 4 4.35 (0.171) 8.2 (0.323) 12.1 (0.476) E2 Min. 6.25 (0.246) 10.25 (0.404) 14.25 (0.561) F 3.5 0.05 (0.138 0.002) 5.5 0.05 (0.217 0.002) 5.5 0.05 (0.217 0.002) P1 4.0 0.10 (0.157 0.004) 8.0 0.10 (0.315 0.004) 8.0 0.10 (0.315 0.004) T2 Max 2.5 (0.098) 4.6 (0.181) 4.6 (0.181) W Max 8.3 (0.327) 12.3 (0.484) 16.3 (0.642) A0,B0 & K0 Note 5 1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 2. The tape with or without components shall pass around R without damage (see Figure 5). 3. If S1<1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Document 481 paragraph 4.3 (b)). 4. B1 dimension is a reference dimension for tape feeder clearance only. 5. The cavity defined by A0, B0 and K0 shall surround the component with sufficient clearance that: (a) the component does not protrude above the top surface of the carrier tape. (b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed. (c) rotation of the component is limited to 20 maximum for 8 and 12mm tapes and 10 maximum for 16mm tapes (see Figure 3). (d) lateral movement of the component is restricted to 0.5 mm maximum for 8mm and 12mm wide tape and to 1.0mm maximum for 16mm tape (see Figure 4). (e) for KPS Series product A0 and B0 are measured on a plane 0.3mm above the bottom of the pocket. (f) see Addendum in EIA Document 481 for standards relating to more precise taping requirements. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 12 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Packaging Information Performance Notes Tape Width 8mm 12mm & 16mm 1. Cover Tape Break Force: 1.0 Kg Minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Peel Strength 0.1 Newton to 1.0 Newton (10gf to 100gf) 0.1 Newton to 1.3 Newton (10gf to 130gf) The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165 to 180 from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 30010 mm/minute. 3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA-556 and EIA-624. Figure 3 - Maximum Component Rotation T Maximum Component Rotation Top View Typical Pocket Centerline Maximum Component Rotation Side View s Bo Tape Width (mm) 8,12 16-200 Maximum Rotation ( 20 10 T) Typical Component Centerline Ao Tape Width (mm) 8,12 16-56 72-200 Maximum Rotation ( 20 10 5 S) Figure 4 - Maximum Lateral Movement 8mm & 12mm Tape 0.5 mm maximum 0.5 mm maximum 16mm Tape 1.0 mm maximum 1.0 mm maximum Figure 5 - Bending Radius Embossed Carrier Punched Carrier R Bending Radius R (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 13 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Figure 6 - Reel Dimensions Full Radius, See Note Access Hole at Slot Location (O 40 mm min.) W3 (Includes flange distortion at outer edge) W2 (Measured at hub) A D (See Note) C (Arbor hole diameter) If present, tape slot in core for tape start: 2.5 mm min. width x 10.0 mm min. depth N W1 (Measured at hub) B (see Note) Note: Drive spokes optional; if used, dimensions B and D shall apply. Table 7 - Reel Dimensions Metric will govern Constant Dimensions -- Millimeters (Inches) Tape Size 8mm 12mm 16mm A 178 0.20 (7.008 0.008) or 330 0.20 (13.000 0.008) B Min 1.5 (0.059) C 13.0 +0.5/-0.2 (0.521 +0.02/-0.008) D Min 20.2 (0.795) Variable Dimensions -- Millimeters (Inches) Tape Size 8mm 12mm 16mm 50 (1.969) N Min 8.4 +1.5/-0.0 (0.331 +0.059/-0.0) 12.4 +2.0/-0.0 (0.488 +0.078/-0.0) 16.4 +2.0/-0.0 (0.646 +0.078/-0.0) W1 W2 Max 14.4 (0.567) 18.4 (0.724) 22.4 (0.882) W3 Shall accommodate tape width without interference (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 14 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Figure 7 - Tape Leader & Trailer Dimensions Embossed Carrier Punched Carrier 8 mm & 12 mm only Carrier Tape Round Sprocket Holes END START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum, Top Cover Tape Components 100 mm Min. Leader 400 mm Minimum, Figure 8 - Maximum Camber Elongated sprocket holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Straight Edge 250 mm (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 15 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 Other KEMET Resources Tools Resource Configure A Part: CapEdge SPICE & FIT Software Search Our FAQs: KnowledgeEdge http://capacitoredge.kemet.com http://www.kemet.com/spice http://www.kemet.com/keask Location Product Information Resource Products Technical Resources (Including Soldering Techniques) RoHS Statement Quality Documents http://www.kemet.com/products http://www.kemet.com/technicalpapers http://www.kemet.com/rohs http://www.kemet.com/qualitydocuments Location Product Request Resource Sample Request Engineering Kit Request http://www.kemet.com/sample http://www.kemet.com/kits Location Contact Resource Website Contact Us Investor Relations Call Us Twitter www.kemet.com http://www.kemet.com/contact http://www.kemet.com/ir 1-877-MyKEMET http://twitter.com/kemetcapacitors Location Disclaimer All product specifications, statements, information and data (collectively, the "Information") are subject to change without notice. All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not be required. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 16 MIL-PRF (CWR Style) Established Reliability - T492 CWR11 Style Mil-PRF-55365/8 KEMET Corporation World Headquarters 2835 KEMET Way Simpsonville, SC 29681 Mailing Address: P.O. Box 5928 Greenville, SC 29606 www.kemet.com Tel: 864-963-6300 Fax: 864-963-6521 Europe Southern Europe Geneva, Switzerland Tel: 41-22-715-0100 Paris, France Tel: 33-1-4646-1009 Sasso Marconi, Italy Tel: 39-051-939111 Milan, Italy Tel: 39-02-57518176 Rome, Italy Tel: 39-06-23231718 Madrid, Spain Tel: 34-91-804-4303 Asia Northeast Asia Hong Kong Tel: 852-2305-1168 Shenzhen, China Tel: 86-755-2518-1306 Beijing, China Tel: 86-10-5829-1711 Shanghai, China Tel: 86-21-6447-0707 Taipei, Taiwan Tel: 886-2-27528585 Corporate Offices Fort Lauderdale, FL Tel: 954-766-2800 North America Southeast Lake Mary, FL Tel: 407-855-8886 Southeast Asia Central Europe Singapore Tel: 65-6586-1900 Penang, Malaysia Tel: 60-4-6430200 Bangalore, India Tel: 91-806-53-76817 Northeast Landsberg, Germany Tel: 49-8191-3350800 Dortmund, Germany Tel: 49-2307-3619672 Kwidzyn, Poland Tel: 48-55-279-7025 Wilmington, MA Tel: 978-658-1663 West Chester, PA Tel: 610-692-4642 Central Schaumburg, IL Tel: 847-882-3590 Carmel, IN Tel: 317-706-6742 Northern Europe Bishop's Stortford, United Kingdom Tel: 44-1279-757201 Weymouth, United Kingdom Tel: 44-1305-830747 Coatbridge, Scotland Tel: 44-1236-434455 Farjestaden, Sweden Tel: 46-485-563934 Espoo, Finland Tel: 358-9-5406-5000 West Milpitas, CA Tel: 408-433-9950 Mexico Zapopan, Jalisco Tel: 52-33-3123-2141 Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 (864) 963-6300 * www.kemet.com T2006-1 * 10/11/2010 17 |
Price & Availability of T492A156J025BC4251
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |