View APW7098QAE-TRG_4998772.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

APW7098
Two- Phase Buck PWM Controller with Integrated MOSFET Drivers
Features
* * * * * * * * * * * * * * * * *
Voltage-Mode Operation with Current Sharing - Adjustable Feedback Compensation - Fast Load Transient Response Operate with 8V~13.2VCC Supply Voltage Selectable External or Internal 0.6V Reference - 1.5% Accuracy Over Temperature Support Single- and Two-Phase Operations 5VCC and Buffered Reference Outputs 8~12V Gate Drivers with Internal Bootstrap Diode Lossless Inductor DCR Current Sensing Selectable Operation Frequency - 150k/300k/400kHz per Phase Power-OK Indicator Output - Regulated 1.5V on REFOUT/POK Adjustable Over-Current Protection (OCP) Accurate Load Line (DROOP) Programming Adjustable Soft-Start Over-Voltage Protection (OVP) Under-Voltage Protection (UVP) Over-Temperature Protection (OTP) QFN4x4 24-Lead Package (QFN4x4-24A) Lead Free and Green Devices Available (RoHS Compliant)
General Description
The APW7098, two-phase PWM control IC, provides a precision voltage regulation system for advanced graphic microprocessors in graphics card applications. The integration of power MOSFET drivers into the controller IC and reduces the number of external parts for a cost and space saving power management solution. The APW7098 uses a voltage-mode PWM architecture, operating with fixed-frequency, to provides excellent load transient response. The device uses the voltage across the DCRs of the inductors for current sensing. Load line voltage positioning (DROOP), channel-current balance, and over-current protection are accomplished through continuous inductor DCR current sensing. The MODE pin programs single- or two- phase operation. When IC operates in two-phase mode normally, it can transfer two-phase mode to single-phase mode at liberty. Nevertheless, once operates in single-phase mode, the operation mode is latched. It is required to toggle SS, REFIN/EN or 5VCC pin to reset the IC. Such feature of the MODE pin makes the APW7098 ideally suitable for dual power input applications, such as PCIE interfaced graphic cards. This control IC` protection features include a set of s sophisticated over-temperature, over-voltage, undervoltage, and over-current protections. Over-voltage results in the converter turning the lower MOSFETs on to clamp the rising output voltage and protects the microprocessor. The over-current protection level is set through external resistors. The device also provides a power-on-reset function and a programmable soft-start to prevent wrong operation and limit the input surge current during power-on or start-up. The APW7098 is available in a QFN4x4-24A package.
Simplified Application Circuit
VIN1 VOUT
REFIN/EN REFOUT/POK
APW7098
COMP FB
VIN2
Applications
* * *
Graphics Card GPU Core Power Supply Motherboard Chipset or DDR SDRAM Core Power Supply On-board High Power PWM Converter with Output Current up to 60A
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders. Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009 1 www.anpec.com.tw
APW7098
Ordering and Marking Information
APW7098 Assembly Material Handling Code Temperature Range Package Code Package Code QA : QFN4x4-24A Operating Ambient Temperature Range E : -20 to 70 oC Handling Code TR : Tape & Reel Assembly Material G : Halogen and Lead Free Device XXXXX - Date Code
APW7098 QA :
APW7098 XXXXX
Note: ANPEC lead-free products contain molding compounds/die attach materials and 100% matte tin plate termination finish; which are fully compliant with RoHS. ANPEC lead-free products meet or exceed the lead-free requirements of IPC/JEDEC J-STD-020D for MSL classification at lead-free peak reflow temperature. ANPEC defines "Green" to mean lead-free (RoHS compliant) and halogen free (Br or Cl does not exceed 900ppm by weight in homogeneous material and total of Br and Cl does not exceed 1500ppm by weight).
Pin Configuration
VCCDRV PHASE1 PHASE2 18 UGATE2 17 BOOT2 25 PGND 16 REFOUT/POK 15 REFIN/EN 14 SS 13 FB 7 CSN1 8 CSN2 9 10 11 12 DROOP COMP CSP2 RT LGATE1 VCC LGATE2
24 23 22 21 20 19 UGATE1 1 BOOT1 2 5VCC 3 AGND 4 MODE 5 CSP1 6
QFN4x4-24A (Top View)
Absolute Maximum Ratings
Symbol VCC VBOOT1/2 VCC Supply Voltage (VCC to AGND)
(Note 1)
Rating -0.3 ~ 15 -0.3 ~ 15 <200ns pulse width >200ns pulse width -5 ~ VBOOT1/2+5 -0.3 ~ VBOOT1/2+0.3 -5 ~ VCC+5 -0.3 ~ VCC+0.3 -10 ~ 30 -2 ~ 15 Unit V V V
Parameter
BOOT1/2 Voltage (BOOT1/2 to PHASE1/2) UGATE1/2 Voltage (UGATE1/2 to PHASE1/2)
LGATE1/2 Voltage (LGATE1/2 to PGND) <200ns pulse width >200ns pulse width PHASE1/2 Voltage (PHASE1/2 to PGND) <200ns pulse width >200ns pulse width V V
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
2
www.anpec.com.tw
APW7098
Absolute Maximum Ratings (Cont.)
Symbol BOOT1/2 to AGND Voltage <200ns pulse width >200ns pulse width VCCDRV to AGND Voltage V5VCC 5VCC Supply Voltage (5VCC to AGND, V5VCC < VCC +0.3V) REFIN/EN, MODE to AGND Voltage Input Voltage (REFOUT/POK, SS, FB, COMP, DROOP, RT, CSP1/2, CSN1/2 to AGND) PGND to AGND Voltage PDMAX Maximum Power Dissipation Maximum Junction Temperature TSTG TSDR Storage Temperature Range Maximum Soldering Temperature, 10 Seconds -0.3 ~ 42 -0.3 ~ 30 -0.3 ~ 15 -0.3 ~ 7 -0.3 ~ 7 -0.3 ~ V5VCC +0.3 -0.3 ~ +0.3 Limited Internally 150 -65 ~ 150 260 V V V V V V W
o o
(Note 1)
Rating Unit
Parameter
C C C
o
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Thermal Characteristics
Symbol JA JC Parameter Junction-to-Ambient Resistance
(Note 2)
Typical Value QFN4x4-24A 45
Unit
Junction-to-Case Resistance (Note 3) QFN4x4-24A
C/W 7
Note 2 : JA is measured with the component mounted on a high effective thermal conductivity test board in free air. The exposed pad of QFN4x4-24A is soldered directly on the PCB. Note 3: The case temperature is measured at the center of the exposed pad on the underside of the QFN4x4-24A package.
Recommended Operating Conditions (Note 4)
Symbol VCC V5VCC VOUT VIN1 VIN2 IOUT VREFIN/EN TA TJ CVCC C5VCC VCC Supply Voltage 5VCC Supply Voltage (V5VCC < VCC +0.3V) Converter Output Voltage PWM 1 Converter Input Voltage PWM 2 Converter Input Voltage Converter Output Current REFIN/EN Input Voltage Ambient Temperature Junction Temperature Linear Regulator Output Capacitor 5VCC Linear Regulator Output Capacitor Parameter Range 8 ~ 13.2 5 5% 0.6 ~ 2.5 3.1 ~ 13.2 3.1 ~ 13.2 ~ 60 0~2 -20 ~ 70 -20 ~ 125 0.8 ~ 15 0.8 ~ 15 Unit V V V V V A V
o o
C C
F F
Note 4 : Refer to the typical application circuits.
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
3
www.anpec.com.tw
APW7098
Electrical Characteristics
Refer to the typical application circuits. These specifications apply over VIN=12V, VOUT=1.2V and TA= -20 ~ 70C, unless otherwise specified. Typical values are at TA=25C. The V5VCC is supplied by the internal regulator.
Symbol SUPPLY CURRENT ICC ISD
Parameter
Test Conditions Min.
APW7098 Typ. Max.
Unit
VCC Nominal Supply Current VCC Shutdown Supply Current
UGATEx and LGATEx Open, FB forced above regulation point SS/EN=GND
-
5 5
10 -
mA mA
POWER-ON-RESET (POR) AND OPERATION PHASE SELECTION V5VCC_THR 5VCC Rising Threshold Voltage 5VCC POR Hysteresis MODE Rising Threshold Voltage IMODE MODE Pin Input Current VMODE Rising 4.2 0.4 0.77 -100 4.5 0.58 0.8 4.8 0.76 0.83 +100 V V V nA
VCC LINEAR CONTROLLER VRRG_VCC Regulated Voltage on VCC Maximum VCCDRV Sink Current 5VCC LINEAR REGULATOR VREG_5VCC Output Voltage Line Regulation Load Regulation Current-Limit REFERENCE VOLTAGE VREF Regulated Voltage on FB pin Accuracy IFB FB Pin Input Current REFIN/EN Voltage Offset VREFIN/EN_THR Device Enable Voltage Threshold Device Enable Voltage Hysteresis Internal/External Reference Selection Voltage Threshold Reference Selection Debounce Time IREFIN/EN VPOK REFIN/EN Pin Input Current REFOUT/POK Output Voltage REFOUT/POK Accuracy REFOUT/POK Current-Limit REFOUT/POK Pull-Low Resistance IO = 0~3mA, TA=25 C IO = 0~3mA, Over temperature REFOUT/POK = GND IREFOUT/POK = 5mA
o
IO=0A, RPULL-UP=1k VCC = VREG_VCC +200mV, VVCCDRV = 8V
8 5
8.5 -
9 -
V mA
IO = 0A, VCC =8V IO = 0A, VCC = 8V ~ 13.2V IO = 3mA, VCC > 8V 5VCC = GND
4.75 -20 -200 20
5 30
5.25 20 200 -
V mV mV mA
Internal reference voltage used TA=25 C Over temperature
o
-1 -1.5 -100
0.6 0.4 50 2.5 20 1.5 8 70
+1 +1.5 +100 5 0.43 3.0 +100 +2 +3 15 100
V % nA mV V mV V s nA V % mA
VFB - VREFIN/EN, VREFIN/EN =0.6V~1.5V On REFIN/EN pin, VREFIN/EN rising
-5 0.37 -
On REFIN/EN pin VREFIN/EN falling, Switching to external reference
2.1 -100 -2 -3 4 -
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
4
www.anpec.com.tw
APW7098
Electrical Characteristics (Cont.)
Refer to the typical application circuits. These specifications apply over VIN=12V, VOUT=1.2V and TA= -20 ~ 70C, unless otherwise specified. Typical values are at TA=25C. The V5VCC is supplied by the internal regulator. Symbol ERROR AMPLIFIER DC Gain Gain-Bandwidth Product Slew Rate Upper Clamp Voltage Lower Clamp Voltage COMP Pull-Low Resistance OSCILLATOR RT = GND FOSC VOSC1/2 IRT Oscillator Frequency RT = Floating RT = 5VCC Oscillator Sawtooth Amplitude RT Input Current RT 5VCC Level RT Floating Voltage RT GND Level Maximum Duty Cycle MOSFET GATE DRIVERS UGATE1/2 Source Current UGATE1/2 Sink Current LGATE1/2 Source Current LGATE1/2 Sink Current UGATE1/2 Source Resistance UGATE1/2 Sink Resistance LGATE1/2 Source Resistance LGATE1/2 Sink Resistance TD Dead-Time VBOOT = 12V, VUGATE-VPHASE = 2V VBOOT = 12V, VUGATE-VPHASE = 2V VCC = 12V, VLGATE = 2V VCC =12V, VLGATE = 2V VBOOT = 12V, 100mA Source Current VBOOT = 12V, 100mA Sink Current VCC = 12V, 100mA Source Current VCC = 12V, 100mA Sink Current 2.6 1 2.6 1.4 2.5 2 2 1.4 30 3.75 3 3 2.1 A A A A ns RT = GND/5VCC(5V) For FOSC =150kHz For FOSC =300kHz For FOSC =400kHz 135 270 360 -100 V5VCC-0.5 1.2 85 150 300 400 1.5 3.6 88 165 330 440 +100 V5VCC-1.2 0.3 V A V V V % kHz RL = 10k to the ground CL = 100pF, RL = 10k to the ground CL = 100pF, IO = O 00A 4 IO = 1mA IO = -1mA In fault or shutdown condition 2.7 85 20 8 3.0 2 0.1 dB MHz V/s V V k Parameter Test Conditions Min. APW7098 Typ. Max. Unit
CURRENT SENSE AND DROOP FUNCTION ICSP ICSN CSP1/2 Pin Input Current CSN1/2 Maximum Output Current Current Sense Amplifier Bandwidth DROOP Output Current Accuracy DROOP Accuracy Current Difference Between Channel1/2 and Average Current RDROOP = 2k, VDROOP =0.005V VFB = VDROOP/20, VDROOP = 1V Sourcing current R CSN1/2 = 2k, Sinking current -100 80 15 -5 -10 3 50 +100 +5 +10 nA A MHz A mV %
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
5
www.anpec.com.tw
APW7098
Electrical Characteristics (Cont.)
Refer to the typical application circuits. These specifications apply over VIN=12V, VOUT=1.2V and TA= -20 ~ 70C, unless otherwise specified. Typical values are at TA=25C. The V5VCC is supplied by the internal regulator. Symbol Parameter Test Conditions Min. SOFT-START AND ENABLE ISS Soft-Start Current Source Soft-Start Complete Threshold SS Pull-low Resistance POWER-OK AND PROTECTIONS Over-Current Trip Level VUV VPOK_L VOV, VPOK_H FB Under-Voltage Threshold POK Lower Threshold FB Over-Voltage Threshold and POK Upper Threshold FB Over-Voltage Hysteresis TOTR Over-Temperature Trip Level Over-Temperature Hysteresis TJ rising ~ 2s noise filter, VFB rising Percentage of VR at Error Amplifier ICS1 + ICS2 ~ 2s noise filter, VFB falling, Percentage of VR at Error Amplifier 110 40 115 120 50 87.5 125 60 150 50 140 60 135 80 A % % % mV
o o
APW7098 Typ. Max.
Unit
Flowing out of SS pin
8 -
10 3.2 10
12 18
A V k
C C
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
6
www.anpec.com.tw
APW7098
Typical Operating Characteristics
5VCC Line Regulation
6
5VCC Load Regulation
6 VCC=12V, VIN=12V
5VCC Voltage,V5VCC (V)
5VCC Voltage,V5VCC (V)
5 4 3 2 1 0 0 2 4 6 8 10 12 14
5 4 3 2 1 0 0 5 10 15 20 25 30 35 40
VCC Voltage,VCC (V)
5VCC Load Current ,I5VCC (mA)
Output Voltage Load Regulation
0.606
0.606
Output Voltage Line Regulation
VCC=12V
Feedback Voltage,VFB (V)
VCC=12V, VIN=12V
Feedback Voltage,VFB (V)
0.604 0.602
0.604 0.602 0.6 0.598 0.596 0.594
0.6
0.598 0.596 0.594 0 10 20 30 40 50
5
6
7
8
9
10
11
12
13
Output Current,IOUT (A)
VIN Voltage,VIN (V)
Reference Voltage Accuracy Over Temperature
0.609
330
Switching Frequency Over Temperature
Reference Voltage,VREF (V)
Switching Frequency, FSW (kHz)
0.607 0.605 0.603 0.601 0.599 0.597 0.595 0.593 0.591 -40 -20 0 20 40 60 80
o
320 310 300 290 280 270 -40
100 120
-20
0
20
40
60
80
o
100
120
Junction Temperature, TJ ( C) Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009 7
Junction Temperature, TJ ( C) www.anpec.com.tw
APW7098
Operating Waveforms
Power On
IOUT=10A V5VCC
Power Off
IOUT=10A V5VCC
1
1
VCOMP
2
VCOMP
2
VSS
VSS
3
VOUT
3
VOUT
4
4
CH1: V5VCC (5V/div) CH2: VCOMP (1V/div) CH3: VSS (5V/div) CH4: VOUT (1V/div) Time: 5ms/div
CH1: V5VCC (5V/div) CH2: VCOMP (1V/div) CH3: VSS (5V/div) CH4: VOUT (1V/div) Time: 5ms/div
Enable by REFIN/EN Pin
IOUT=10A VREFIN/EN
Shutdown by REFIN/EN Pin
IOUT=10A VREFIN/EN
1
VCOMP
1
VCOMP
2
VSS
2
VSS
3
3
VOUT
4
VOUT
4 CH1: VREFIN/EN (5V/div) CH2: VCOMP (1V/div) CH3: VSS (2V/div) CH4: VOUT (1V/div) Time: 5ms/div
CH1: VREFIN/EN (5V/div) CH2: VCOMP (1V/div) CH3: VSS (2V/div) CH4: VOUT (1V/div) Time: 5ms/div
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
8
www.anpec.com.tw
APW7098
Operating Waveforms (Cont.)
External Step-Up Reference by VREFIN/EN
VREFIN/EN 1 VFB VSS 2 3 4 CH1: VREFIN/EN (1V/div) CH2: VFB (500mV/div) CH3: VSS (1V/div) CH4: IOUT (10A/div) Time: 200s/div IOUT
External Step-Down Reference by VREFIN/EN
VREFIN/EN 1 VFB VSS 2 3 4 IOUT
CH1: VREFIN/EN (1V/div) CH2: VFB (500mV/div) CH3: VSS (1V/div) CH4: IOUT (10A/div) Time: 200s/div
Power On Without VIN2 Voltage
VOUT 1 VPHASE1 2 VPHASE2 3 Vss CH1: VOUT (1V/div) CH2: VPHASE1 (10V/div) CH3: VPHASE2 (2V/div) CH4: VSS (2V/div) Time: 5ms/div
2 1
Under-Voltage Protection (UVP)
VFB
VPHASE1
VPHASE2 3 Vss 4 CH1: VFB (500mV/div) CH2: VPHASE1 (10V/div) CH3: VPHASE2 (10V/div) CH4: VSS (2V/div) Time: 200s/div
4
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
9
www.anpec.com.tw
APW7098
Operating Waveforms (Cont.)
Load Transient , 0A==>40A
1 2 3 VPHASE1 IPHASE2 VOUT
Load Transient , 40A==>0A
VPHASE1 1 IPHASE2 2 VOUT 3 IOUT
RSEN=3k L=0.56H DCR=4m
IOUT 4 CH1: VPHASE1 (20V/div) CH2: IPHASE2 (20A/div) CH3: VOUT (AC, 200mV/div) CH4: IOUT (10A/div) Time: 20s/div
RSEN=3k L=0.56H DCR=4m
4 CH1: VPHASE1 (20V/div) CH2: IPHASE2(20A/div) CH3: VOUT (AC, 200mV/div) CH4: IOUT (10A/div) Time: 20s/div
OCP at Slow Slew IOUT
Short-Circuit Test After Power On
RSEN=1.5k L=0.56H DCR=4m
IL1
RSEN=1.5k L=0.56H DCR=4m
IL1
1
1
IL2 2 3 4 CH1: IL1 (10A/div) CH2: IL2 (10A/div) CH3: VSS (5V/div) CH4: VOUT (1V/div) Time: 5ms/div VSS VOUT
IL2 2 3 4 CH1: IL1 (10A/div) CH2: IL2 (10A/div) CH3: VSS (5V/div) CH4: VOUT (1V/div) Time: 5ms/div VSS VOUT
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
10
www.anpec.com.tw
APW7098
Operating Waveforms (Cont.)
Short-Circuit Test Before Power On
RSEN=1.5k L=0.56H DCR=4m IL1
OVP After Power On
Pull-Up VFB > V OV VFB VSS
1
1
2
IL2
VLG1
2 3 4 CH1: IL1 (10A/div) CH2: IL2 (10A/div) CH3: VSS (5V/div) CH4: VOUT (1V/div) Time: 5ms/div
VSS
3
VLG2
4
VOUT
CH1: VFB (1V/div) CH2: VSS (2V/div) CH3: VLG1 (10V/div) CH4: VLG2 (10V/div) Time: 100s/div
Pin Description
PIN NO. 1 NAME UGATE1 High-side Gate Driver Output for channel 1. Connect this pin to the gate of high-side MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the high-side MOSFET has turned off. Bootstrap Supply for the floating high-side gate driver of channel 1. Connect the Bootstrap capacitor between the BOOT1 pin and the PHASE1 pin to form a bootstrap circuit. The bootstrap capacitor provides the charge to turn on the high-side MOSFET. Typical values for CBOOT ranged from 0.1F to 1F. Ensure that CBOOT is placed near the IC. Internal Regulator Output. This is the output pin of the linear regulator, which is converting power from VCC and provides output current up to 20mA minimums for internal bias and external usage. Signal Ground for the IC. All voltage levels are measured with respect to this pin. Tie this pin to the ground island/plane through the lowest impedance connection available. Operation Phase Selection Input. Pulling this pin lower than 0.64V sets two-phase operation with both channels enabled. Pulling this pin higher than 0.8V sets single-phase operation with the channel 2 disabled. Once operating in single-phase mode, the operation mode is latched. It is required to toggle SS, REFIN/EN, or 5VCC pin to reset the IC. Positive Input of current sensing Amplifier for channel 1. This pin combined with CSN1 senses the inductor current through an RC network. Negative Input of current sensing amplifier for channel 1. This pin combined with CSP1 senses the inductor current through an RC network. Negative Input of current sensing amplifier for channel 2. This pin combined with CSP2 senses the inductor current through an RC network. Positive Input of current sensing Amplifier for Channel 2. This pin combined with CSN2 senses the inductor current through an RC network. FUNCTION
2
BOOT1
3 4
5VCC AGND
5
MODE
6 7 8 9
CSP1 CSN1 CSN2 CSP2
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
11
www.anpec.com.tw
APW7098
Pin Description (Cont.)
PIN NO. NAME Load Line (droop) Setting. Connect a resistor between this pin and AGND to set the droop. A sourcing current, proportional to output current is present on the DROOP pin. The droop scale factor is set by the resistors (connected with CSP1, CSP2, and DROOP), resistance of the output inductors, and the internal voltage divider with the ratio of 5%. Operating Frequency Setting. The three-level input pin sets the operating frequency for each channel. RT Operating Frequency (kHz) GND 150 Floating 300 5VCC 400 Error Amplifier Output. Connect the compensation network between COMP, FB, and VOUT for Type 2 or Type 3 feedback compensation. Feedback Voltage. This pin is the inverting input to the error comparator. A resistor divider from the output to the AGND is used to set the regulation voltage. Soft-start Current Output. Connect a capacitor from this pin to the AGND to set the soft-start interval. Pulling the voltage on this pin below 0.5V causes COMP to pull low and then shuts off the output. External Reference and Enable Input. The IC uses the voltage (VREFIN/EN) as reference voltage of the converter with soft-start control. If this pin is driven by an external voltage ranged from 0.4V to 2V. The IC is disabled if the voltage is below 0.4V (typical). If external reference is not available, then connect this pin to 5VCC for internal 0.6V reference. Power-OK and 1.5V Reference Output. This pin is a reference output used to indicate the status of the voltages on SS pin and FB pin. REFOUT/POK provides 1.5V reference if VFB> 87.5% of reference (VR). Bootstrap Supply for the floating high-side gate driver of channel 2. Connect the Bootstrap capacitor between the BOOT2 pin and the PHASE2 pin to form a bootstrap circuit. The bootstrap capacitor provides the charge to turn on the high-side MOSFET. Typical values for CBOOT range from 0.1F to 1F. Ensure that CBOOT is placed near the IC. High-side Gate Driver Output for Channel 2. Connect this pin to the gate of high-side MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the high-side MOSFET has turned off. Switch Node for Channel 2. Connect this pin to the source of high-side MOSFET and the drain of the low-side MOSFET. This pin is used as sink for UGATE2 driver. This pin is also monitored by the adaptive shoot-through protection circuitry to determine when the high-side MOSFET has turned off. An Schottky diode between this pin and the ground is recommended to reduce negative transient voltage that is common in a power supply system. Low-side Gate Driver Output for Channel 2. Connect this pin to the gate of low-side MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the low-side MOSFET has turned off. Drive for External Linear Regulator. This pin is the drive output for the external linear regulator. Connect this pin to base/gate of NPN/NMOS transistor as the pass element. Supply Voltage. This pin along with VCCDRV pin and external pass element provides 8.5V regulated bias supply, low-side gate drivers, and the bootstrap circuit for high-side drivers. This pin can receive a well-decoupled 8V~13.2V supply voltage alone if the VCCDRV is left open. Ensure that this pin is bypassed by a ceramic capacitor next to the pin. Low-side Gate Driver Output for Channel 1. Connect this pin to the gate of low-side MOSFET. This pin is monitored by the adaptive shoot-through protection circuitry to determine when the low-side MOSFET has turned off. FUNCTION
10
DROOP
11
RT
12 13
COMP FB
14
SS
15
REFIN/EN
16
REFOUT/PO K
17
BOOT2
18
UGATE2
19
PHASE2
20
LGATE2
21
VCCDRV
22
VCC
23
LGATE1
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
12
www.anpec.com.tw
APW7098
Pin Description (Cont.)
PIN NO. NAME Switch Node for Channel 1. Connect this pin to the source of high-side MOSFET and the drain of the low-side MOSFET. This pin is used as sink for UGATT1 driver. This pin is also monitored by the adaptive shoot-through protection circuitry to determine when the high-side MOSFET has turned off. An Schottky diode between this pin and the ground is recommended to reduce negative transient voltage, which is common in a power supply system. Power Ground for the low-side gate drivers. Connect this pin to the source of low-side MOSFETs. This pin is used as sink for LGATE1 and LGATE2 drivers. FUNCTION
24
PHASE1
25
PGND
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
13
www.anpec.com.tw
APW7098
Block Diagram
REFOUT/POK VCCDRV VCC
1.5V Reference
VCC Linear Controller 8.5V 87.5%
VCC
5VCC Linear Regulator
5VCC
125%
OV UV
Power-onReset
V5VCC
50%
FB DROOP
Droop Control
SSEND
Over-Temperature Protection
PGND
Control Logic
0.6V VREF
'' L''
-
Operation Phase Selection
3.6V
MODE
REFIN/EN
V5VCC-1V 0.4V
''H''
+
VR
Error Amplifier ISS 10A
Soft-Start
SS COMP AGND
RT
VCC
Selectable Oscillator and Sawtooth
150/300/400 kHz
VOSC1
VOSC2 VCC
BOOT2 UGATE2 PHASE2 LGATE2
120A ICS1+ICS2 OC VCC
BOOT1 PWM Signal Controller
VCC
UGATE1 PHASE1 LGATE1
CSN2 CSP2
Current Sense
ICS2
Current Balance
ICS1 ICS1+ICS2
Current Sense
CSN1 CSP1
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
14
www.anpec.com.tw
APW7098
Typical Application Circuits
1. APW7098 PWM Converter With 8V Gate Drive
VIN +12V BOOT1 MODE UGATE1
21 22 1 24 2
C16 1F R10 1.2k
R12 1k
5
C4 10F Q1 C5 0.1F L1 0.56H DCR=4m C6 1200Fx3 VOUT 1.2V C7 47Fx2 IOCP=45A Q1 : APM4350KPx1 Q2 : APM4354KPx2
Q5 2N7002 C13 1F C14 1F
VCCDRV PHASE1 VCC LGATE1 5VCC PGND REFIN/EN SS
23 25
Q2
3 15
14
APW7098
BOOT2 17 C8 10F Q3 C10 0.1F L2 0.56H DCR=4m C9 330Fx3
C15 0.1F FOSC=300kHz
11
RT
UGATE2 18 PHASE2
19
10
DROOP REFOUT/POK
R11 2k C3 2.2nF R4 2k C2 22nF
16
LGATE2
20
Q4
CSP1
12 13
6 7 9 8
R5 1.5k PHASE1 PHASE2 C12 0.1F (X7R) R7 1.5k C11 0.1F (X7R)
CSN1 COMP FB AGND
4
CSP2 CSN2
R2 1.5k
R1 1.5k
R3 51 C1 10nF
R8 1.5k
R6 1.5k
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
15
www.anpec.com.tw
APW7098
Typical Application Circuits (Cont.)
2. APW7098 PWM Converter With 12V Gate Drive
VIN +12V BOOT1 MODE UGATE1
21 22 1 24 2
5
C4 10F Q1 C5 0.1F L1 0.56H DCR=4m C6 1200uFx3 VOUT 1.2V C7 47Fx2 IOCP=45A Q1 : APM4350KPx1 Q2 : APM4354KPx2
VCCDRV PHASE1 VCC 5VCC REFIN/EN SS LGATE1 PGND
C13 1F C14 1F
23 25
Q2
3 15
14
APW7098
BOOT2
17
C15 0.1F FOSC=300kHz
11
C8 10F Q3 C10 0.1F L2 0.56H DCR=4m
C9 330Fx3
RT
UGATE2 18 PHASE2
19
10
DROOP REFOUT/POK
R11 2k C3 2.2nF R4 2k C2 22nF
16
LGATE2
20
Q4
CSP1
12 13
6 7 9 8
R5 1.5k PHASE1 PHASE2 C12 0.1F (X7R) R7 1.5k C11 0.1F (X7R)
CSN1 COMP FB AGND
4
CSP2 CSN2
R2 1.5k
R1 1.5k
R3 51 C1 10nF
R8 1.5k
R6 1.5k
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
16
www.anpec.com.tw
APW7098
Function Description
VCC Linear Controller The VCC linear-regulator controller is an analog gain block with an open-drain n-channel output. It drives an external NPN or N-channel MOSFET pass transistor with a 1k (typical) pull-up resistor and senses the feedback voltage via VCC pin. The regulator uses a 1F (minimum) ceramic output capacitor and is designed to deliver 100mA (at 8.5V) for VCC. 5VCC Linear Regulator 5VCC is the output terminal of the internal 5V linear regulator which regulates a 5V voltage on 5VCC by controlling an internal bypass transistor between VCC and 5VCC. The linear regulator powers the internal control circuitry and is stable with a low-ESR ceramic output capacitor. Bypass 5VCC to GND with a ceramic capacitor of at least 1F. Place the capacitor physically close to the IC to provide good noise decoupling. The linear regulator can also provide output current up to 20mA for external loads. The linear regulator with currentlimit protection can protect itself during over-load or shortcircuit conditions on 5VCC pin. The 5VCC linear regulator stops regulating in Over-Temperature Protection. When the junction temperature is cooled by 50oC, the 5VCC linear regulator starts to regulate the output voltage again. 5VCC Power-On-Reset (POR) and REFIN/EN (External Reference and Enable Input) Figure 1 shows the power sequence. The APW7098 keeps monitoring the voltage on 5VCC pin to prevent wrong logic operations which may occur when 5VCC voltage is not high enough for the internal control circuitry to operate. The 5VCC POR has a rising threshold of 4.6V (typical) with 0.58V of hysteresis. After the 5VCC voltage exceeds its rising Power-On-Reset (POR) voltage threshold, the IC starts a start-up process and then ramps up the output voltage to the setting of output voltage. The 5VCC POR signal resets the fault latch, set by the under-voltage or over-current event, when the signal is at a low level.
VSS_VT 5VCC POR V5VCC VPOK VFB 1.5V 0.6V Voltage(V) VCC VSS
Time
Figure 1. Power Sequence
When soft-start is initiated, the internal 10A current source starts to charge the capacitor. When the soft-start voltage across the soft-start capacitor reaches the enabled threshold about 0.8V (VSS_VT), the internal reference starts to rise and follows the soft-start voltage with converter operating at 150k/300k/400kHz PWM switching frequency. When output voltage rises to 87.5% of the regulation voltage, the power-ok is enabled. The softstart time (from the moment of enabling the IC to the moment when VPOK goes high) can be expressed as the following equation:
TSS = CSS x (VSS_VT + VREF x 0.875) ISS
where CSS= external soft-start capacitor VSS_VT= internal soft-start threshold voltage, is about 0.8V VREF= 0.6V or the voltage on the REFIN/EN pin ISS= soft-start current=10A During soft-start stage, the under-voltage protection is inhibited; however, the over-voltage and over-current protection functions are enabled. If the output capacitor has residue voltage before start-up, both lower and upper MOSFETs are in off-state until the internal soft-start voltage equals to the FB pin voltage. This will ensure the output voltage starts from its existing voltage level. Reference Voltage Selection and Shutdown Control The APW7098 features a reference selection function to use either internal 0.6V or external reference voltage. During the beginning of soft-start, the voltage on
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
17
www.anpec.com.tw
APW7098
Function Description (Cont.)
Reference Voltage Selection and Shutdown Control (Cont.) REFIN/EN pin determines which reference voltage is used. If this REFIN/EN pin is driven by an external voltage ranged from 0.4V to 2V, the IC uses the VREFIN/EN voltage as reference voltage of the converter with softstart control. If external reference is not available, connect this pin to 5VCC for internal 0.6V reference used. Once the internal or external reference is selected, the reference source is latched. Cycling the POR signal resets the latch. The other function of REFIN/EN pin is used to enable or shut off the IC. Pulling the VREFIN/EN voltage below 0.4V (typical) shuts down the two-phase PWM controller. In the shutdown mode, the two-phase UGATE and LGATE signals are pulled to PHASE and PGND respectively, the output is floating. Operation Phase Selection The MODE pin programs single- or two- phase operation. It has a typical value for rising threshold of 0.8V, VMODE_THR, with 0.16V of hysteresis (0.64V), VMODE_THF. When the MODE pin voltage is higher than VMODE_THR, the device operates in single-phase; when the MODE pin voltage is lower than VMODE_THF and VIN2 supply voltage is above approximate 4V, the device operates in two-phase operation. This function makes the APW7098 ideally suitable for dual power input applications like PCIE interfaced graphic cards. The figure 2 shows the power sources of the two channels. The input power of PWM1 converter is supplied by PCIE bus power and the input power of PWM2 converter is supplied by an external power. If the input power connector of PWM2 converter is not plugged into the socket before start-up, the internal VIN2 sensing circuit can sense the absence of VIN2 and set the IC to operate in single-phase mode with PWM2 disabled. When the IC operates in two-phase mode, it can switch the operating mode from two-phase to single-phase operation. Once operating in single-phase mode, the operation mode is latched. It is required to toggle SS, REFIN/EN, or 5VCC pin to reset the IC. Figure 2. VIN2 Sensing Circuit Over-Voltage Protection (OVP) The over-voltage protection function monitors the output voltage through the FB pin. When the FB voltage increases over 125% of the reference voltage (VR) due to the high-side MOSFET failure or other reasons, the overvoltage protection comparator designed with a 2s noise filter will force the low-side MOSFET gate drivers high. This action actively pulls down the output voltage and eventually attempts to trigger the over-current shutdown of an ATX power supply. As soon as the output voltage is within regulation, the OVP comparator is disengaged. The chip will restore its normal operation. When the OVP occurs, the REFOUT/POK will drop to low as well. This OVP scheme only clamps the voltage overshoot, and does not invert the output voltage when otherwise activated with a continuously high output from low-side MOSFETs driver, which is a common problem for OVP schemes with a latch. Under-Voltage Protection (UVP) In the process of operation, when a short-circuit occurs, the output voltage will drop quickly. Before the over-current protection responds, the output voltage will fall out of the required regulation range. The under-voltage continually monitors the VFB voltage after soft-start is completed. If a load step is strong enough to pull the output voltage lower than the under-voltage threshold, the IC shuts down converter' output. Cycling the 5VCC s POR or REFIN/EN signal resets the fault latch and starts a start-up process. The under-voltage threshold is 50% of the nominal output voltage. The under-voltage comparator has a built-in 2s noise filter to prevent the chips from wrong UVP shutdown being caused by noise.
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009 18 www.anpec.com.tw
External Power PCIE +12V VCC
PWM 1 converter MODE VIN2 PWM 2 converter PHASE2 Operation Phase Selection
4V
VIN2 sensing circuit
APW7098
Function Description (Cont.)
Over-Current Protection (OCP) Figure 3 shows the circuit of sensing inductor current. Connecting a series resistor (R S) and a capacitor (C S) network in parallel with the inductor and measuring the voltage (VC) across the capacitor can sense the inductor current.
L PHASE IL Rs CSP CSN R2 Cs VC VL DCR
Current Sharing The APW7098 uses inductor' DCRs and external nets works to sense the both currents flowing through the inductors of the PWM1 and PWM2 channels. The current sharing circuit, with closed-loop control, uses the sensed currents to adjust the two-phase inductor currents. For example, if the sensed current of PWM1 is bigger than PWM2, the duty of PWM1 will decrease and the duty of PWM2 will increase. Then, the device will reduce IL1 current and increase IL2 current for current sharing. DROOP In some high current applications, a requirement on precisely controlled output impedance is imposed. This dependence of output voltage on load current is often termed droop regulation. As shown in figure 4, the droop control block generates a voltage through external resistor R DROOP and then set the droop voltage. The droop voltage, VDROOP , is proportional to the total current in two channels. As shown in the following equation:
VDROOP = 0.05 x [(ICS1 + ICS 2 ) x RDROOP ]
Figure 3. Illustration of Inductor Current Sensing Circuit The equations of the sensing network are:
VL (s)=IL (s) x (SL+DCR)
VC(S) = VL(S) x
1 IL(S) x (SL + DCR ) = 1 + SRSCS 1 + SRSCS
Take
L DCR for example, if the above equation is true, the voltage R SC S =
The VDROOP voltage is used the regulator to adjust the output voltage, therefore, it is equal to the reference voltage minus the droop voltage.
across the capacitor CS is equal to voltage drop across the inductor DCR, and the voltage VC is proportional to the current IL. The sensing current through the resistor R2 can be expressed as the following equation:
ICS = IL x DCR R2
Droop Control VDROOP RDROOP VREFIN/EN or 0.6V
where ICS is the sensed current IL is the inductor current DCR is the inductor resistance R2 is the sense resistor The APW7098 is a two-phase PWM controller; therefore, the IC has two sensed current parts, ICS1 and ICS2. When ICS1 plus ICS2 is greater than 120A, the over current occurs. In over-current protection, the IC shuts off the converter and then initials a new soft-start process. After 3 overcurrent events are counted, the device turns off both highside and low-side MOSFETs and the converter' output s is latched to be floating.
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009 19
VR
Figure 4. Illustration of Droop Setting Function
www.anpec.com.tw
APW7098
Function Description (Cont.)
Over-Temperature Protection (OTP) When the junction temperature increases above the rising threshold temperature TOTR, the IC will enter the overtemperature protection state that suspends the PWM, which forces the LGATE and UGATE gate drivers to output low voltages and turns off the 5VCC linear regulator output. The thermal sensor allows the converters to start a start-up process and regulate the output voltage again after the junction temperature cools by 50oC. The OTP is designed with a 50oC hysteresis to lower the average TJ during continuous thermal overload conditions, which increases lifetime of the APW7098.
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
20
www.anpec.com.tw
APW7098
Application Information
Output Voltage Setting The output voltage is adjustable from 0.6V to 2.5V with a resistor-divider connected with FB, AGND, and converter' output. Using 1% or better resistors for the s resistor-divider is recommended. The output voltage is determined by:
R VOUT = 0.6 x 1 + TOP RGND
GAIN (dB) FESR FLC
-40dB/dec
Where 0.6 is the reference voltage, RTOP is the resistor connected from converter' output to FB, and RGND is the s resistor connected from FB to the the AGND. Suggested RGND is in the range from 1K to 20k. To prevent stray pickup, locate resistors R TOP and R GND close to the APW7098. PWM Compensation The output LC filter of a step down converter introduces a double pole, which contributes with -40dB/decade gain slope and 180 degrees phase shift in the control loop. A compensation network among COMP, FB, and V OUT should be added. The compensation network is shown in Figure 8. The output LC filters consists of the output inductors and output capacitors. For two-phase convertor, when assuming VIN1=VIN2=VIN, L1=L2=L, the transfer function of the LC filter is given by: 1 + s x ESR x COUT 1 s x L x COUT + s x ESR x COUT + 1 2 The poles and zero of this transfer functions are: 1 FLC = 1 2x x L x COUT 2 1 FESR = 2 x x ESR x COUT GAINLC =
2
-20dB/dec
Frequency(Hz)
Figure 6. Frequency Resopnse of the LC filters The PWM modulator is shown in figure 7. The input is the output of the error amplifier and the output is the PHASE node. The transfer function of the PWM modulator is given by : GAINPWM = VIN VOSC
Driver OSC PWM Comparator PHASE
VIN
VOSC Output of Error Amplifier Driver
Figure 7. The PWM Modulator The compensation network is shown in figure 8. It provides a close loop transfer function with the highest zero crossover frequency and sufficient phase margin. The transfer function of error amplifier is given by :
The FLC is the double-pole frequency of the two-phase LC filters, and FESR is the frequency of the zero introduced by the ESR of the output capacitors.
V PHASE1 L1=L L2=L V PHASE2 COUT ESR V OUT
GAINAMP
1 1 // R2 + VCOMP sC1 sC2 = = 1 VOUT R1// R3 + sC3
Figure 5. The Output LC Filter
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009 21
1 1 s + xs + R2 x C2 (R1 + R3) x C3 R1 + R3 = x C1 + C2 1 R1x R3 x C1 s s + x s + R2 x C1x C2 R3 x C3
www.anpec.com.tw
APW7098
Application Information (Cont.)
PWM Compensation (Cont.) The pole and zero frequencies of the transfer function are:
FZ1 = 1 2 x x R2 x C2
4. Set the pole at the ESR zero frequency FESR: FP1 = FESR Calculate the C1 by the following equation: C1 = C2 2 x x R2 x C2 x FESR - 1
1 2 x x (R1+ R3) x C3 1 FP1 = C1x C2 2 x x R2 x C1 + C2 1 FP2 = 2 x x R3 x C3 FZ2 =
C1 R3 VOUT R1 FB VREF VCOMP C3 R2 C2
5. Set the second pole FP2 at the half of the switching frequency and also set the second zero FZ2 at the output LC filter double pole FLC. The compensation gain should not exceed the error amplifier open loop gain, check the compensation gain at FP2 with the capabilities of the error amplifier. FP2 = 0.5 X FSW FZ2 = FLC Combine the two equations will get the following component calculations:
R3 =
Figure 8. Compensation Network The closed loop gain of the converter can be written as: GAINLC X GAINPWM X GAINAMP Figure 9. shows the asymptotic plot of the closed loop converter gain, and the following guidelines will help to design the compensation network. Using the below guidelines should give a compensation similar to the
GAIN (dB)
R1 FSW -1 2 x FLC
1 x R3 x FSW
C3 =
FZ1
FZ2
FP1
FP2
curve plotted. A stable closed loop has a -20dB/ decade slope and a phase margin greater than 45 degree. 1. Choose a value for R1, usually between 1K and 5K. 2. Select the desired zero crossover frequency FO= (1/5 ~ 1/10) X FSW Use the following equation to calculate R2: VOSC FO R2 = x x R1 VIN FLC 3. Place the first zero FZ1 before the output LC filter double pole frequency FLC. FZ1 = 0.75 X FLC Calculate the C2 by the equation: 1 C2 = 2 x x R2 x FLC x 0.75
20log (R2/R1)
Compensation Gain 20log (VIN/G OSC) V
FLC FESR PWM & Filter Gain Converter Gain
Frequency(Hz)
Figure 9. Converter Gain and Frequency Output Inductor Selection The duty cycle (D) of a buck converter is the function of the input voltage and output voltage. Once an output voltage is fixed, it can be written as:
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
22
www.anpec.com.tw
APW7098
Application Information (Cont.)
Output Inductor Selection (Cont.) D= VOUT VIN caused by the AC peak-to-peak sum of the inductor' s current. The ripple voltage of output capacitors can be represented by:
VCOUT = VESR IP - P 8 x COUT x FSW = IP - P x RESR
For two-phase converter, the inductor value (L) determines the sum of the two inductor ripple currents, IP-P, and affects the load transient reponse. Higher inductor value reduces the output capacitors'ripple current and induces lower output ripple voltage. The ripple current can be approxminated by:
IP - P = VIN - 2VOUT VOUT x FSW x L VIN
These two components constitute a large portion of the total output voltage ripple. In some applications, multiple capacitors have to be paralleled to achieve the desired ESR value. If the output of the converter has to support another load with high pulsating current, more capacitors are needed in order to reduce the equivalent ESR and suppress the voltage ripple to a tolerable level. A small decoupling capacitor in parallel for bypassing the noise is also recommended, and the voltage rating of the output capacitors are also must be considered. To support a load transient that is faster than the switching frequency, more capacitors are needed for reducing the voltage excursion during load step change. For getting same load transient response, the output capacitance of two-phase converter only needs around half of output capacitance of single-phase converter. Another aspect of the capacitor selection is that the total AC current going through the capacitors has to be less than the rated RMS current specified on the capacitors in order to prevent the capacitor from overheating. Input Capacitor Selection Use small ceramic capacitors for high frequency decoupling and bulk capacitors to supply the surge current needed each time high-side MOSFET turns on. Place the small ceramic capacitors physically close to the MOSFETs and between the drain of high-side MOSFET and the source of low-side MOSFET. The important parameters for the bulk input capacitor are the voltage rating and the RMS current rating. For reliable operation, select the bulk capacitor with voltage and current ratings above the maximum input voltage and largest RMS current required by the circuit. The capacitor voltage rating should be at least 1.25 times greater than the maximum input voltage and a voltage rating of 1.5 times is a conservative guideline. For two-phase converter, the
23 www.anpec.com.tw
Where FSW is the switching frequency of the regulator. Although the inductor value and frequency are increased and the ripple current and voltage are reduced, a tradeoff exists between the inductor' ripple current and the regus lator load transient response time. A smaller inductor will give the regulator a faster load transient response at the expense of higher ripple current. Increasing the switching frequency (FSW ) also reduces the ripple current and voltage, but it will increase the switching loss of the MOSFETs and the power dissipation of the converter. The maximum ripple current occurs at the maximum input voltage. A good starting point is to choose the ripple current to be approximately 30% of the maximum output current. Once the inductance value has been chosen, select an inductor that is capable of carrying the required peak current without going into saturation. In some types of inductors, especially core that is made of ferrite, the ripple current will increase abruptly when it saturates. This results in a larger output ripple voltage. Output Capacitor Selection Output voltage ripple and the transient voltage deviation are factors that have to be taken into consideration when selecting output capacitors. Higher capacitor value and lower ESR reduce the output ripple and the load transient drop. Therefore, selecting high performance low ESR capacitors is recommended for switching regulator applications. In addition to high frequency noise related to MOSFET turn-on and turn-off, the output voltage ripple includes the capacitance voltage drop VCOUT and ESR voltage drop V ESR
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
APW7098
Application Information (Cont.)
Input Capacitor Selection (Cont.) RMS current of the bulk input capacitor is roughly calculated as the following equation :
IRMS IOUT = x 2D (1 - 2D) 2
Phigh-side = IOUT (1+ TC)(RDS(ON))D + (0.5)( IOUT)(VIN)( tSW)FSW Plow-side = IOUT (1+ TC)(RDS(ON))(1-D) where I
OUT 2
2
is the load current
For a through hole design, several electrolytic capacitors may be needed. For surface mount design, solid tantalum capacitors can be used, but caution must be exercised with regard to the capacitor surge current rating. MOSFET Selection The APW7098 requires two N-Channel power MOSFETs on each phase. These should be selected based upon RDS(ON), gate supply requirements, and thermal management requirements. In high-current applications, the MOSFET power dissipation, package selection, and heatsink are the dominant design factors. The power dissipation includes two loss components, conduction loss, and switching loss. The conduction losses are the largest component of power dissipation for both the high-side and the lowside MOSFETs. These losses are distributed between the two MOSFETs according to duty factor (see the equations below). Only the high-side MOSFET has switching losses since the low-side MOSFETs body diode or an external Schottky rectifier across the lower MOSFET clamps the switching node before the synchronous rectifier turns on. These equations assume linear voltagecurrent transitions and do not adequately model power loss due the reverse-recovery of the low-side MOSFET body diode. The gate-charge losses are dissipated by the APW7098 and don' heat the MOSFETs. However, t large gate-charge increases the switching interval, tSW which increases the high-side MOSFET switching losses. Ensure that all MOSFETs are within their maximum junction temperature at high ambient temperature by calculating the temperature rise according to package thermal-resistance specifications. A separate heatsink may be necessary depending upon MOSFET power, package type, ambient temperature and air flow. For the high-side and low-side MOSFETs, the losses are approximately given by the following equations:
TC is the temperature dependency of RDS(ON) FSW is the switching frequency tSW is the switching interval D is the duty cycle Note that both MOSFETs have conduction losses while the high-side MOSFET includes an additional transition loss. The switching interval, t SW , is the function of the reverse transfer capacitance CRSS. The (1+TC) term is a factor in the temperature dependency of the RDS(ON) and can be extracted from the "RDS(ON) vs. Temperature" curve of the power MOSFET. Layout Consideration In any high switching frequency converter, a correct layout is important to ensure proper operation of the regulator. With power devices switching at higher frequency, the resulting current transient will cause voltage spike across the interconnecting impedance and parasitic circuit elements. As an example, consider the turn-off transition of the PWM MOSFET. Before turn-off condition, the MOSFET is carrying the full load current. During turn-off, current stops flowing in the MOSFET and is freewheeling by the low side MOSFET and parasitic diode. Any parasitic inductance of the circuit generates a large voltage spike during the switching interval. In general, using short and wide printed circuit traces should minimize interconnecting impedances and the magnitude of voltage spike. Besides, signal and power grounds are to be kept separating and finally combined using ground plane construction or single point grounding. The best tie-point between the signal ground and the power ground is at the negative side of the output capacitor on each channel, where there is less noise. Noisy traces beneath the IC are not recommended. Figure 10. illustrates the layout, with bold lines indicating high current paths; these traces must be short and wide. Components along the bold lines should be placed lose together. Below is a checklist for your layout:
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
24
www.anpec.com.tw
APW7098
Application Information (Cont.)
Layout Consideration (Cont.)
*
Keep the switching nodes (UGATEx, LGATEx, BOOTx, and PHASEx) away from sensitive small signal nodes since these nodes are fast moving signals. Therefore, keep traces to these nodes as short as possible and there should be no other weak signal traces in parallel with theses traces on any layer.
APW7098
V IN1=V IN
* The signals going through theses traces have both
high dv/dt and high di/dt with high peak charging and discharging current. The traces from the gate drivers to the MOSFETs (UGATEx and LGATEx) should be short
BOOT1
UGATE1 L1 PHASE1 LGATE1 RS1 CS1 V OUT
*
and wide. Place the source of the high-side MOSFET and the drain of the low-side MOSFET as close as possible. Minimizing the impedance with wide layout plane between the two pads reduces the voltage bounce of the node. In addition, the large layout plane between the drain of the MOSFETs (VIN and PHASEx nodes) can get better heat sinking.
CSP1 CSN1 CSN2 CSP2
CS2 RS2
L O A D
* For experiment result of accurate current sensing, the
current sensing components are suggested to place close to the inductor part. To avoid the noise interference, the current sensing trace should be away
LGATE2 PHASE2 UGATE2
L2
*
from the noisy switching nodes. Decoupling capacitors, the resistor-divider, and boot capacitor should be close to their pins. (For example, place the decoupling ceramic capacitor close to the
BOOT2
*
drain of the high-side MOSFET as close as possible). The input bulk capacitors should be close to the drain of the high-side MOSFET, and the output bulk capacitors should be close to the loads. The input capacitor' ground should be close to the grounds of the s output capacitors and low-side MOSFET.
VIN2 =V IN
Figure 10. Layout Guidelines
* Locate the resistor-divider close to the FB pin to minimize the high impedance trace. In addition, FB pin traces can' be close to the switching signal traces t (UGATEx, LGATEx, BOOTx, and PHASEx).
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
25
www.anpec.com.tw
APW7098
Package Information
QFN4x4-24A
D A
E
Pin 1
D2
A1 A3
e S Y M B O L A A1 A3 b D D2 E E2 e L K 0.35 0.20 0.18 3.90 2.00 3.90 2.00 0.50 BSC 0.45 0.014 0.008 QFN4x4-24A MILLIMETERS MIN. 0.80 0.00 0.20 REF 0.30 4.10 2.50 4.10 2.50 0.008 0.154 0.079 0.154 0.079 0.020 BSC 0.018 MAX. 1.00 0.05 MIN. 0.031 0.000 0.008 REF 0.012 0.161 0.098 0.161 0.098 INCHES MAX. 0.039 0.002
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
26
L
K
E2
Pin 1 Corner
b
www.anpec.com.tw
APW7098
Carrier Tape & Reel Dimensions
OD0 P0 P2 P1 A E1 F K0 B SECTION A-A T B0 A0 OD1 B A SECTION B-B
d
Application
A 330.0O .00 2
H 50 MIN. P1 8.0O .10 0
H A
T1
T1
C
d 1.5 MIN. D1 1.5 MIN.
D 20.2 MIN. T 0.6+0.00 -0.40
W
W
E1
F 5.5O .05 0 K0 1.30O .20 0 (mm)
12.4+2.00 13.0+0.50 -0.00 -0.20 P2 2.0O .05 0 D0 1.5+0.10 -0.00
12.0O .30 1.75O .10 0 0 A0 4.30O .20 0 B0 4.30O .20 0
QFN4x4-24A
P0 4.0O .10 0
Devices Per Unit
Package Type QFN4x4-24A Unit Tape & Reel Quantity 3000
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
27
www.anpec.com.tw
APW7098
Taping Direction Information
QFN4x4-24A
USER DIRECTION OF FEED
Classification Profile
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
28
www.anpec.com.tw
APW7098
Classification Reflow Profiles
Profile Feature Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) Average ramp-up rate (Tsmax to TP) Liquidous temperature (TL) Time at liquidous (tL) Peak (Tp)* package body Temperature Sn-Pb Eutectic Assembly 100 C 150 C 60-120 seconds 3 C/second max. 183 C 60-150 seconds See Classification Temp in table 1 20** seconds 6 C/second max. 6 minutes max. Pb-Free Assembly 150 C 200 C 60-120 seconds 3C/second max. 217 C 60-150 seconds See Classification Temp in table 2 30** seconds 6 C/second max. 8 minutes max.
Time (tP)** within 5C of the specified classification temperature (Tc) Average ramp-down rate (Tp to Tsmax) Time 25C to peak temperature
* Tolerance for peak profile Temperature (Tp) is defined as a supplier minimum and a user maximum. ** Tolerance for time at peak profile temperature (tp) is defined as a supplier minimum and a user maximum. Table 1. SnPb Eutectic Process - Classification Temperatures (Tc) Package Thickness <2.5 mm 2.5 mm
3
Volume mm <350 235 C 220 C
3
Volume mm 350 220 C 220 C
3
3
Table 2. Pb-free Process - Classification Temperatures (Tc) Package Thickness <1.6 mm 1.6 mm - 2.5 mm 2.5 mm Volume mm <350 260 C 260 C 250 C Volume mm 350-2000 260 C 250 C 245 C Volume mm >2000 260 C 245 C 245 C
3
Reliability Test Program
Test item SOLDERABILITY HOLT PCT TCT HBM MM Latch-Up Method JESD-22, B102 JESD-22, A108 JESD-22, A102 JESD-22, A104 MIL-STD-883-3015.7 JESD-22, A115 JESD 78 Description 5 Sec, 245C 1000 Hrs, Bias @ 125C 168 Hrs, 100%RH, 2atm, 121C 500 Cycles, -65C~150C VHBMU2KV VMMU200V 10ms, 1trU 100mA
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
29
www.anpec.com.tw
APW7098
Customer Service
Anpec Electronics Corp. Head Office : No.6, Dusing 1st Road, SBIP, Hsin-Chu, Taiwan, R.O.C. Tel : 886-3-5642000 Fax : 886-3-5642050 Taipei Branch : 2F, No. 11, Lane 218, Sec 2 Jhongsing Rd., Sindian City, Taipei County 23146, Taiwan Tel : 886-2-2910-3838 Fax : 886-2-2917-3838
Copyright (c) ANPEC Electronics Corp. Rev. A.6 - Oct., 2009
30
www.anpec.com.tw

▲Up To Search▲

Price & Availability of APW7098QAE-TRG

	To Download APW7098QAE-TRG Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .