|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
ELECTRONIC COMPONENTS RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de Anderungen vorbehalten / subject to change without notice 150W Quad Output with PFC Function Features : QP-150 Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage Forced air cooling by built-in DC fan CH4: Polarity is selectable Fixed switching frequency at 100KHz 3 years warranty series .. SPECIFICATION MODEL OUTPUT NUMBER DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER (max.) OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE(OPTION) WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE QP-150-3A CH1 5V 10A 3 ~ 15A 146W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 3.14 ~ 3.63V 6.0% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 3.3V 10A 0 ~ 15A CH3 12V 5A 0.4 ~ 5A CH4 -5V 0.6A 0 ~ 1A QP-150-3B CH1 5V 10A 3 ~ 15A 150.2W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 3.14 ~ 3.63V 6.0% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 3.3V 10A 0 ~ 15A CH3 12V 5A 0.4 ~ 5A CH4 -12V 0.6A 0 ~ 1A QP-150-3C CH1 5V 10A 3 ~ 15A 152W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 3.14 ~ 3.63V +8,-6% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 3.3V 10A 0 ~ 15A CH3 15V 4A 0.4 ~ 5A CH4 -15V 0.6A 0 ~ 1A RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p 100mVp-p 100mVp-p 150mVp-p 150mVp-p 800ms, 50ms/230VAC 24ms/230VAC 90 ~ 264VAC 47 ~ 63Hz PF>0.95/230VAC 73% 2.5A/115VAC COLD START 800ms, 50ms/115VAC at full load 24ms/115VAC at full load 127 ~ 370VDC PF>0.98/115VAC at full load 75% 1.2A/230VAC 40A/230V 74% <3.5mA / 240VAC 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V Protection type : Shut down o/p voltage, re-power on to recover 95 5 (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) HARMONIC CURRENT EMS IMMUNITY MTBF Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 141.5K hrs min. MIL-HDBK-217F (25 ) 199*99*50mm (L*W*H) 0.93Kg; 20pcs/19.6Kg/1.28CUFT OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:QP-150-SPEC 2006-08-22 150W Quad Output with PFC Function Features : QP-150 Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage Forced air cooling by built-in DC fan CH4: Polarity is selectable Fixed switching frequency at 100KHz 3 years warranty series .. SPECIFICATION MODEL OUTPUT NUMBER DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER (max.) OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE(OPTION) WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE QP-150-3D CH1 5V 10A 3 ~ 15A 150.2W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 3.14 ~ 3.63V 6.0% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 3.3V 10A 0 ~ 15A CH3 24V 2.5A 0.3 ~ 3A CH4 -12V 0.6A 0 ~ 1A QP-150D CH1 5V 10A 3 ~ 15A 150.2W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 11.4 ~ 13.2V 6.0% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 12V 4A 0 ~ 5A CH3 24V 2A 0.4 ~ 3A CH4 -12V 0.6A 0 ~ 1A QP-150F CH1 5V 10A 3 ~ 15A 152W CH1: 4.75 ~ 5.5V 3.0% 1.0% 2.0% 3.0% 1.0% 2.0% CH2: 14.3 ~ 16.5V 6.0% 2.0% 6.0% 5.0% 1.0% 2.0% CH2 15V 3A 0 ~ 5A CH3 24V 2A 0.4 ~ 3A CH4 -15V 0.6A 0 ~ 1A RIPPLE & NOISE (max.) Note.2 100mVp-p 100mVp-p 150mVp-p 150mVp-p 120mVp-p 150mVp-p 200mVp-p 150mVp-p 120mVp-p 150mVp-p 200mVp-p 150mVp-p 800ms, 50ms/230VAC 24ms/230VAC 90 ~ 264VAC 47 ~ 63Hz PF>0.95/230VAC 76% 2.5A/115VAC COLD START 800ms, 50ms/115VAC at full load 24ms/115VAC at full load 127 ~ 370VDC PF>0.98/115VAC at full load 78% 1.2A/230VAC 40A/230V 78% <3.5mA / 240VAC 105 ~ 150% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed CH1:5.75 ~ 6.75V CH2:3.8 ~ 4.4V CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover CH2:13.8 ~ 16.2V CH1:5.75 ~ 6.75V CH2:17.25 ~ 20.25V 95 5 (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) HARMONIC CURRENT EMS IMMUNITY MTBF Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 141.5K hrs min. MIL-HDBK-217F (25 199*99*50mm (L*W*H) 0.93Kg; 20pcs/19.6Kg/1.28CUFT ) OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:QP-150-SPEC 2006-08-22 ELECTRONIC COMPONENTS RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de Anderungen vorbehalten / subject to change without notice 150W Quad Output with PFC Function Mechanical Specification 199 20 55 15 168 65 QP-150 Case No. 916B series Unit:mm LED 10 9 8 7 6 5 4 3 2 1 +V ADJ.2 +V ADJ.1 2-M4 7.62 79 51 49.5 Air flow direction 25 10 4-M4 L=6mm 6.15 5-M3 L=6mm Terminal Pin No. Assignment : Assignment Assignment Pin No. Pin No. AC/L DC OUTPUT V3 1 5 AC/N DC OUTPUT V1 2 6,7 FG DC OUTPUT COM 3 8,9 DC OUTPUT V4 DC OUTPUT V2 4 10 25 117 Block Diagram FAN fosc : 100KHz RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER O.V.P. REGULATOR V4 V3 RECTIFIERS & FILTER V2 +5V COM DETECTION CIRCUT I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING PWM & PFC CONTROL FG Derating Curve Output Derating VS Input Voltage 100 100 90 80 80 70 60 LOAD (%) LOAD (%) 40 60 50 40 20 -10 -10 0 0 10 20 30 40 50 60 (HORIZONTAL) 90 100 115 135 155 230 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name:QP-150-SPEC 2006-08-22 ELECTRONIC COMPONENTS RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de Anderungen vorbehalten / subject to change without notice 12.5 25 50 38 99 ELECTRONIC COMPONENTS RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de Anderungen vorbehalten / subject to change without notice 150W Quad Output with PFC Function Features : QP-150B,C Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage Forced air cooling by built-in DC fan Fixed switching frequency at 100KHz 3 years warranty series .. SPECIFICATION MODEL OUTPUT NUMBER DC VOLTAGE RATED CURRENT CURRENT RANGE RATED POWER (max.) OUTPUT VOLTAGE ADJ. RANGE VOLTAGE TOLERANCE Note.3 LINE REGULATION LOAD REGULATION SETUP, RISE TIME HOLD TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE POWER FACTOR (Typ.) INPUT EFFICIENCY (Typ.) AC CURRENT (Typ.) INRUSH CURRENT (Typ.) LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE(OPTION) WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE QP-150B CH1 5V 15A 3 ~ 15A 150W 150mVp-p 6.0% 2.0% 6.0% 150mVp-p +10,-6% 2.0% 6.0% 100mVp-p 5.0% 1.0% 2.0% CH1:4.75 ~ 5.5V 3.0% 1.0% 2.0% 24ms at full load 90 ~ 264VAC 47 ~ 63Hz PF>0.95/230VAC 76% 2.5A/115VAC COLD START 1.2A/230VAC 40A PF>0.98/115VAC at full load 77% 127 ~ 370VDC CH2 12V 4A 0.4 ~ 5A CH3 -12V 2A 0.3 ~ 2A CH4 -5V 0.6A 0 ~ 1A QP-150C CH1 5V 15A 3 ~ 15A 153W 100mVp-p CH1:4.75 ~ 5.5V 3.0% 1.0% 2.0% +6,-10% 2.0% 6.0% 8.0% 2.0% 6.0% 5.0% 1.0% 2.0% 150mVp-p 150mVp-p 100mVp-p CH2 15V 3A 0.4 ~ 4A CH3 -15V 2A 0.3 ~ 2A CH4 -5V 0.6A 0 ~ 1A RIPPLE & NOISE (max.) Note.2 100mVp-p 1000ms, 50ms at full load <3.5mA / 240VAC 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed CH1:5.75 ~ 6.75V Protection type : Shut down o/p voltage, re-power on to recover 95 5 (TSW1) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0~50 ) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) HARMONIC CURRENT EMS IMMUNITY MTBF Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 141.5K hrs min. MIL-HDBK-217F (25 199*99*50mm (L*W*H) 1.1Kg; 20pcs/22Kg/1.28CUFT ) OTHERS NOTE DIMENSION PACKING 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:QP-150B,C-SPEC 2006-08-22 150W Quad Output with PFC Function Mechanical Specification 199 20 55 15 168 65 QP-150B,C Case No. 916B series Unit:mm LED 10 +V ADJ.1 9 8 7 6 5 4 3 2 1 7.62 79 51 49.5 Air flow direction 25 10 4-M4 L=6mm 2-M4 6.15 5-M3 L=6mm Terminal Pin No. Assignment : Assignment Assignment Pin No. Pin No. AC/L DC OUTPUT V3 1 5 AC/N DC OUTPUT V1 2 6,7 FG DC OUTPUT COM 3 8,9 DC OUTPUT V4 DC OUTPUT V2 4 10 25 117 Block Diagram RECTIFIERS & FILTER RECTIFIERS & FILTER MA & CONTROL RECTIFIERS & FILTER O.V.P. REGULATOR fosc : 100KHz V4 V3 I/P EMI FILTER & RECTIFIERS PFC CIRCUIT POWER SWITCHING PWM & PFC CONTROL FAN RECTIFIERS & FILTER V2 +5V COM DETECTION CIRCUT FG Derating Curve Output Derating VS Input Voltage 100 100 90 80 80 70 60 LOAD (%) LOAD (%) 40 60 50 40 20 -10 -10 0 0 10 20 30 40 50 60 (HORIZONTAL) 90 100 115 135 155 230 264 AMBIENT TEMPERATURE ( ) INPUT VOLTAGE (VAC) 60Hz File Name:QP-150B,C-SPEC 2006-08-22 ELECTRONIC COMPONENTS RSG RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 info@rsg-electronic.de www.rsg-electronic.de Anderungen vorbehalten / subject to change without notice 12.5 25 50 38 99 |
Price & Availability of QP-150-3A |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |