View PIC16C74B-04L_147718.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PIC16C63A/65B/73B/74B
8-Bit CMOS Microcontrollers with A/D Converter
Devices included in this data sheet:
* PIC16C63A * PIC16C65B * PIC16C73B * PIC16C74B
PIC16C7X Peripheral Features:
* Timer0: 8-bit timer/counter with 8-bit prescaler * Timer1: 16-bit timer/counter with prescaler can be incremented during SLEEP via external crystal/clock * Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler * Capture, Compare, PWM modules - Capture is 16-bit, max. resolution is 200 ns - Compare is 16-bit, max. resolution is 200 ns - PWM max. resolution is 10-bit * 8-bit multichannel Analog-to-Digital converter * Synchronous Serial Port (SSP) with SPITM and I2CTM * Universal Synchronous Asynchronous Receiver Transmitter (USART/SCI) * Parallel Slave Port (PSP), 8-bits wide with external RD, WR and CS controls * Brown-out detection circuitry for Brown-out Reset (BOR)
PIC16CXX Microcontroller Core Features:
* High performance RISC CPU * Only 35 single word instructions to learn * All single cycle instructions except for program branches which are two cycle * Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle * 4 K x 14 words of Program Memory, 192 x 8 bytes of Data Memory (RAM) * Interrupt capability * Eight-level deep hardware stack * Direct, indirect and relative addressing modes * Power-on Reset (POR) * Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) * Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation * Programmable code protection * Power-saving SLEEP mode * Selectable oscillator options * Low power, high speed CMOS EPROM technology * Wide operating voltage range: 2.5V to 5.5V * High Sink/Source Current 25/25 mA * Commercial, Industrial and Automotive temperature ranges * Low power consumption: - < 5 mA @ 5V, 4 MHz - 23 A typical @ 3V, 32 kHz - < 1.2 A typical standby current Devices PIC16C63A PIC16C65B PIC16C73B PIC16C74B I/O Pins 22 33 22 33 A/D Chan. 5 8 PSP No Yes No Yes Interrupts 10 11 11 12
Pin Diagram:
PDIP, Windowed CERDIP
MCLR/VPP RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI RA5/SS/AN4 RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 VDD VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RD0/PSP0 RD1/PSP1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21
RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT VDD VSS RD7/PSP7 RD6/PSP6 RD5/PSP5 RD4/PSP4 RC7/RX/DT RC6/TX/CK RC5/SDO RC4/SDI/SDA RD3/PSP3 RD2/PSP2
2000 Microchip Technology Inc.
PIC16C65B PIC16C74B
DS30605C-page 1
PIC16C63A/65B/73B/74B
SDIP, SOIC, Windowed CERDIP
MCLR/VPP RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI RA5/SS/AN4 VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RA3/AN3/VREF RA2/AN2 RA1/AN1 RA0/AN0 MCLR/VPP NC RB7 RB6 RB5 RB4 NC
*1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15
PLCC
MQFP TQFP
RB3 RB2 RB1 RB0/INT VDD VSS RD7/PSP7 RD6/PSP6 RD5/PSP5 RD4/PSP4 RC7/RX/DT
18 19 20 21 22 23 24 25 26 27 28
Key Features PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) Program Memory (EPROM) x 14 Data Memory (Bytes) x 8 Pins Parallel Slave Port Capture/Compare/PWM Modules Timer Modules A/D Channels Serial Communication In-Circuit Serial Programming Brown-out Reset Interrupt Sources Packages
RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RD0/PSP0 RD1/PSP1 RD2/PSP2 RD3/PSP3 RC4/SDI/SDA RC5/SDO RC6/TX/CK NC
PIC16C63A 4K 192 28 -- 2 3 -- SPI/I2C, USART Yes Yes 10 28-pin SDIP, SOIC, SSOP, Windowed CERDIP
PIC16C65B 4K 192 40 Yes 2 3 -- SPI/I2C, USART Yes Yes 11 40-pin PDIP; 44-pin PLCC, MQFP, TQFP, Windowed CERDIP
NC NC RB4 RB5 RB6 RB7 MCLR/VPP RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF
12 13 14 15 16 17 18 19 20 21 22
RA4/T0CKI RA5/SS/AN4 RE0/RD/AN5 RE1/WR/AN6 RE2/CS/AN7 VDD VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI NC
6 5 4 3 2 1 44 43 42 41 40
7 8 9 10 11 12 13 14 15 16 17
PIC16C65B PIC16C74B
39 38 37 36 35 34 33 32 31 30 29
44 43 42 41 40 39 38 37 36 35 34
RC6/TX/CK RC5/SDO RC4/SDI/SDA RD3/PSP3 RD2/PSP2 RD1/PSP1 RD0/PSP0 RC3/SCK/SCL RC2/CCP1 RC1/T1OSI/CCP2 NC
RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT VDD VSS RC7/RX/DT RC6/TX/CK RC5/SDO RC4/SDI/SDA
PIC16C63A PIC16C73B
RC7/RX/DT RD4/PSP4 RD5/PSP5 RD6/PSP6 RD7/PSP7 VSS VDD RB0/INT RB1 RB2 RB3
1 2 3 4 5 6 7 8 9 10 11
PIC16C65B PIC16C74B
33 32 31 30 29 28 27 26 25 24 23
NC RC0/T1OSO/T1CKI OSC2/CLKOUT OSC1/CLKIN VSS VDD RE2/CS/AN7 RE1/WR/AN6 RE0/RD/AN5 RA5/SS/AN4 RA4/T0CKI
PIC16C73B 4K 192 28 -- 2 3 5 SPI/I2C, USART Yes Yes 11 28-pin SDIP, SOIC, SSOP, Windowed CERDIP
PIC16C74B 4K 192 40 Yes 2 3 8 SPI/I2C, USART Yes Yes 12 40-pin PDIP; 44-pin PLCC, MQFP, TQFP, Windowed CERDIP
DS30605C-page 2
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
Table of Contents
1.0 General Description...................................................................................................................................................................... 5 2.0 PIC16C63A/65B/73B/74B Device Varieties ................................................................................................................................. 7 3.0 Architectural Overview ................................................................................................................................................................. 9 4.0 Memory Organization ................................................................................................................................................................. 15 5.0 I/O Ports ..................................................................................................................................................................................... 29 6.0 Timer0 Module ........................................................................................................................................................................... 39 7.0 Timer1 Module ........................................................................................................................................................................... 43 8.0 Timer2 Module ........................................................................................................................................................................... 47 9.0 Capture/Compare/PWM Modules .............................................................................................................................................. 49 10.0 Synchronous Serial Port (SSP) Module ..................................................................................................................................... 55 11.0 Addressable Universal Synchronous Asynchronous Receiver Transmitter (USART)................................................................ 65 12.0 Analog-to-Digital Converter (A/D) Module ................................................................................................................................. 79 13.0 Special Features of the CPU...................................................................................................................................................... 85 14.0 Instruction Set Summary ............................................................................................................................................................ 99 15.0 Development Support............................................................................................................................................................... 107 16.0 Electrical Characteristics .......................................................................................................................................................... 113 17.0 DC and AC Characteristics Graphs and Tables....................................................................................................................... 139 18.0 Packaging Information.............................................................................................................................................................. 153 Appendix A: Revision History ........................................................................................................................................................ 165 Appendix B: Device Differences..................................................................................................................................................... 165 Appendix C: Device Migrations - PIC16C63/65A/73A/74A PIC16C63A/65B/73B/74B ............................................................. 166 Appendix D: Migration from Baseline to Mid-Range Devices......................................................................................................... 168 On-Line Support................................................................................................................................................................................. 175 Reader Response .............................................................................................................................................................................. 176 Product Identification System ............................................................................................................................................................ 177
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@mail.microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) * The Microchip Corporate Literature Center; U.S. FAX: (480) 792-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using.
Customer Notification System
Register on our web site at www.microchip.com/cn to receive the most current information on all of our products.
2000 Microchip Technology Inc.
DS30605C-page 3
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 4
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
1.0 GENERAL DESCRIPTION
The PIC16C63A/65B/73B/74B devices are low cost, high performance, CMOS, fully-static, 8-bit microcontrollers in the PIC16CXX mid-range family. All PICmicro(R) microcontrollers employ an advanced RISC architecture. The PIC16CXX microcontroller family has enhanced core features, eight-level deep stack and multiple internal and external interrupt sources. The separate instruction and data buses of the Harvard architecture allow a 14-bit wide instruction word with the separate 8-bit wide data. The two stage instruction pipeline allows all instructions to execute in a single cycle, except for program branches, which require two cycles. A total of 35 instructions (reduced instruction set) are available. Additionally, a large register set gives some of the architectural innovations used to achieve a very high performance. The PIC16C63A/73B devices have 22 I/O pins. The PIC16C65B/74B devices have 33 I/O pins. Each device has 192 bytes of RAM. In addition, several peripheral features are available, including: three timer/ counters, two Capture/Compare/PWM modules, and two serial ports. The Synchronous Serial Port (SSP) can be configured as either a 3-wire Serial Peripheral Interface (SPI) or the two-wire Inter-Integrated Circuit (I 2C) bus. The Universal Synchronous Asynchronous Receiver Transmitter (USART) is also known as the Serial Communications Interface or SCI. Also, a 5channel high speed 8-bit A/D is provided on the PIC16C73B, while the PIC16C74B offers 8 channels. The 8-bit resolution is ideally suited for applications requiring low cost analog interface, e.g., thermostat control, pressure sensing, etc. The PIC16C63A/65B/73B/74B devices have special features to reduce external components, thus reducing cost, enhancing system reliability and reducing power consumption. There are four oscillator options, of which the single pin RC oscillator provides a low cost solution, the LP oscillator minimizes power consumption, XT is a standard crystal, and the HS is for high speed crystals. The SLEEP (power-down) feature provides a power-saving mode. The user can wake-up the chip from SLEEP through several external and internal interrupts and RESETS. A highly reliable Watchdog Timer (WDT), with its own on-chip RC oscillator, provides protection against software lockup, and also provides one way of waking the device from SLEEP. A UV erasable CERDIP packaged version is ideal for code development, while the cost effective One-TimeProgrammable (OTP) version is suitable for production in any volume. The PIC16C63A/65B/73B/74B devices fit nicely in many applications ranging from security and remote sensors to appliance control and automotive. The EPROM technology makes customization of application programs (transmitter codes, motor speeds, receiver frequencies, etc.) extremely fast and convenient. The small footprint packages make this microcontroller series perfect for all applications with space limitations. Low cost, low power, high performance, ease of use and I/O flexibility make the PIC16C63A/ 65B/73B/74B devices very versatile, even in areas where no microcontroller use has been considered before (e.g., timer functions, serial communication, capture and compare, PWM functions and coprocessor applications).
1.1
Family and Upward Compatibility
Users familiar with the PIC16C5X microcontroller family will realize that this is an enhanced version of the PIC16C5X architecture. Please refer to Appendix A for a detailed list of enhancements. Code written for the PIC16C5X can be easily ported to the PIC16CXX family of devices (Appendix B).
1.2
Development Support
PICmicro(R) devices are supported by the complete line of Microchip Development tools. Please refer to Section 15.0 for more details about Microchip's development tools.
2000 Microchip Technology Inc.
DS30605C-page 5
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 6
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
2.0 PIC16C63A/65B/73B/74B DEVICE VARIETIES
2.3 Quick-Turnaround-Production (QTP) Devices
A variety of frequency ranges and packaging options are available. Depending on application and production requirements, the proper device option can be selected using the information in the PIC16C63A/65B/73B/74B Product Identification System section at the end of this data sheet. When placing orders, please use that page of the data sheet to specify the correct part number. For the PIC16C7X family, there are two device "types" as indicated in the device number: 1. C, as in PIC16C74. These devices have EPROM type memory and operate over the standard voltage range. LC, as in PIC16LC74. These devices have EPROM type memory and operate over an extended voltage range.
Microchip offers a QTP Programming Service for factory production orders. This service is made available for users who choose not to program a medium to high quantity of units and whose code patterns have stabilized. The devices are identical to the OTP devices but with all EPROM locations and configuration options already programmed by the factory. Certain code and prototype verification procedures apply before production shipments are available. Please contact your local Microchip Technology sales office for more details.
2.4
Serialized Quick-Turnaround Production (SQTPSM) Devices
2.
2.1
UV Erasable Devices
Microchip offers a unique programming service where a few user-defined locations in each device are programmed with different serial numbers. The serial numbers may be random, pseudo-random or sequential. Serial programming allows each device to have a unique number, which can serve as an entry code, password or ID number.
The UV erasable version, offered in windowed CERDIP packages, is optimal for prototype development and pilot programs. This version can be erased and reprogrammed to any of the oscillator modes. Microchip's PICSTART Plus and PRO MATE II programmers both support programming of the PIC16C63A/65B/73B/74B.
2.2
One-Time-Programmable (OTP) Devices
The availability of OTP devices is especially useful for customers who need the flexibility for frequent code updates and small volume applications. The OTP devices, packaged in plastic packages, permit the user to program them once. In addition to the program memory, the configuration bits must also be programmed.
2000 Microchip Technology Inc.
DS30605C-page 7
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 8
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
3.0 ARCHITECTURAL OVERVIEW
The high performance of the PIC16CXX family can be attributed to a number of architectural features commonly found in RISC microprocessors. To begin with, the PIC16CXX uses a Harvard architecture, in which program and data are accessed from separate memories using separate buses. This improves bandwidth over traditional von Neumann architecture, in which program and data are fetched from the same memory using the same bus. Separating program and data buses further allows instructions to be sized differently than the 8-bit wide data word. Instruction opcodes are 14-bits wide, making it possible to have all single word instructions. A 14-bit wide program memory access bus fetches a 14-bit instruction in a single cycle. A two-stage pipeline overlaps fetch and execution of instructions (Example 3-1). Consequently, most instructions execute in a single cycle (200 ns @ 20 MHz) except for program branches. All devices covered by this data sheet contain 4K x 14-bit program memory and 192 x 8-bit data memory. The PIC16CXX can directly, or indirectly, address its register files or data memory. All Special Function Registers, including the program counter, are mapped in the data memory. The PIC16CXX has an orthogonal (symmetrical) instruction set that makes it possible to carry out any operation on any register using any addressing mode. This symmetrical nature and lack of `special optimal situations' make programming with the PIC16CXX simple yet efficient. In addition, the learning curve is reduced significantly. PIC16CXX devices contain an 8-bit ALU and working register. The ALU is a general purpose arithmetic unit. It performs arithmetic and Boolean functions between the data in the working register and any register file. The ALU is 8-bits wide and capable of addition, subtraction, shift and logical operations. Unless otherwise mentioned, arithmetic operations are two's complement in nature. In two-operand instructions, typically one operand is the working register (W register). The other operand is a file register or an immediate constant. In single operand instructions, the operand is either the W register or a file register. The W register is an 8-bit working register used for ALU operations. It is not an addressable register. Depending on the instruction executed, the ALU may affect the values of the Carry (C), Digit Carry (DC), and Zero (Z) bits in the STATUS register. The C and DC bits operate as a borrow bit and a digit borrow out bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples.
2000 Microchip Technology Inc.
DS30605C-page 9
PIC16C63A/65B/73B/74B
FIGURE 3-1: PIC16C63A/65B/73B/74B BLOCK DIAGRAM
13 Program Counter EPROM Program Memory 8 Level Stack (13-bit) RAM File Registers RAM Addr(1) 9 PORTB RB0/INT Indirect Addr RB7:RB1 Data Bus 8 PORTA RA0/AN0(2) RA1/AN1(2) RA2/AN2(2) RA3/AN3/VREF(2) RA4/T0CKI RA5/SS/AN4(2)
Program Bus
14 Instruction reg Direct Addr 7
Addr MUX 8
FSR reg STATUS reg 8 3 PORTC RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT PORTD(3) W reg RD0/PSP0 RD1/PSP1 RD2/PSP2 RD3/PSP3 RD4/PSP4 RD5/PSP5 RD6/PSP6 RD7/PSP7 PORTE(3) RE0/RD/AN5(2,3) Timer0 Timer1 Timer2 A/D(2) RE1/WR/AN6(2,3) RE2/CS/AN7(2,3)
Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Oscillator Start-up Timer Power-on Reset Watchdog Timer Brown-out Reset 8
MUX
ALU
Parallel Slave Port MCLR VDD, VSS
(3)
CCP1
CCP2
Synchronous Serial Port
USART
Note 1: Higher order bits are from the STATUS register. 2: A/D is not available on the PIC16C63A/65B. 3: PSP and Ports D and E are not available on PIC16C63A/73B.
DS30605C-page 10
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 3-1:
Pin Name OSC1/CLKIN OSC2/CLKOUT
PIC16C63A/73B PINOUT DESCRIPTION
DIP Pin# 9 10 SOIC Pin# 9 10 I/O/P Type I O Buffer Type Description
ST/CMOS(3) Oscillator crystal input/external clock source input. -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, the OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. Master clear (RESET) input or programming voltage input. This pin is an active low RESET to the device. PORTA is a bi-directional I/O port. RA0 can also be analog input 0(4). RA1 can also be analog input 1(4). RA2 can also be analog input 2(4). RA3 can also be analog input 3 or analog reference voltage(4). RA4 can also be the clock input to the Timer0 module. Output is open drain type. RA5 can also be analog input 4(4) or the slave select for the synchronous serial port. PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs.
MCLR/VPP
1
1
I/P
ST
RA0/AN0(4) RA1/AN1(4) RA2/AN2(4) RA3/AN3/VREF(4) RA4/T0CKI RA5/SS/AN4(4)
2 3 4 5 6 7
2 3 4 5 6 7
I/O I/O I/O I/O I/O I/O
TTL TTL TTL TTL ST TTL
RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7 RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT VSS VDD
21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 8, 19 20
21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 8, 19 20
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O P P
TTL/ST(1) TTL TTL TTL TTL TTL TTL/ST(2) TTL/ST(2) ST ST ST ST ST ST ST ST -- --
RB0 can also be the external interrupt pin.
Interrupt-on-change pin. Interrupt-on-change pin. Interrupt-on-change pin. Serial programming clock. Interrupt-on-change pin. Serial programming data. PORTC is a bi-directional I/O port. RC0 can also be the Timer1 oscillator output or Timer1 clock input. RC1 can also be the Timer1 oscillator input or Capture2 input/Compare2 output/PWM2 output. RC2 can also be the Capture1 input/Compare1 output/PWM1 output. RC3 can also be the synchronous serial clock input/output for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). RC5 can also be the SPI Data Out (SPI mode). RC6 can also be the USART Asynchronous Transmit or Synchronous Clock. RC7 can also be the USART Asynchronous Receive or Synchronous Data. Ground reference for logic and I/O pins. Positive supply for logic and I/O pins.
Legend: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. 3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. 4: A/D module is not available in the PIC16C63A.
2000 Microchip Technology Inc.
DS30605C-page 11
PIC16C63A/65B/73B/74B
TABLE 3-2:
Pin Name OSC1/CLKIN OSC2/CLKOUT
PIC16C65B/74B PINOUT DESCRIPTION
DIP Pin# 13 14 PLCC Pin# 14 15 TQFP I/O/P MQFP Type Pin# 30 31 I O Buffer Type Description
ST/CMOS(4) Oscillator crystal input/external clock source input. -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. Master clear (RESET) input or programming voltage input. This pin is an active low RESET to the device. PORTA is a bi-directional I/O port. RA0 can also be analog input 0(5). RA1 can also be analog input 1(5). RA2 can also be analog input 2(5). RA3 can also be analog input 3 or analog reference voltage(5). RA4 can also be the clock input to the Timer0 timer/ counter. Output is open drain type. RA5 can also be analog input 4(5) or the slave select for the synchronous serial port. PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs.
MCLR/VPP
1
2
18
I/P
ST
RA0/AN0
(5)
2 3 4
(5)
3 4 5 6 7 8
19 20 21 22 23 24
I/O I/O I/O I/O I/O I/O
TTL TTL TTL TTL ST TTL
RA1/AN1(5) RA2/AN2(5) RA3/AN3/VREF RA4/T0CKI RA5/SS/AN4(5)
5 6 7
RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7
33 34 35 36 37 38 39 40
36 37 38 39 41 42 43 44
8 9 10 11 14 15 16 17
I/O I/O I/O I/O I/O I/O I/O I/O
TTL/ST(1) TTL TTL TTL TTL TTL TTL/ST(2) TTL/ST(2)
RB0 can also be the external interrupt pin.
Interrupt-on-change pin. Interrupt-on-change pin. Interrupt-on-change pin. Serial programming clock. Interrupt-on-change pin. Serial programming data.
Legend: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. 3: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave Port mode (for interfacing to a microprocessor bus). 4: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. 5: A/D is not available on the PIC16C65B.
DS30605C-page 12
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 3-2:
Pin Name
PIC16C65B/74B PINOUT DESCRIPTION (CONTINUED)
DIP Pin# PLCC Pin# TQFP I/O/P MQFP Type Pin# Buffer Type Description PORTC is a bi-directional I/O port.
RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT
15 16 17 18 23 24 25 26
16 18 19 20 25 26 27 29
32 35 36 37 42 43 44 1
I/O I/O I/O I/O I/O I/O I/O I/O
ST ST ST ST ST ST ST ST
RC0 can also be the Timer1 oscillator output or a Timer1 clock input. RC1 can also be the Timer1 oscillator input or Capture2 input/Compare2 output/PWM2 output. RC2 can also be the Capture1 input/Compare1 output/ PWM1 output. RC3 can also be the synchronous serial clock input/ output for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). RC5 can also be the SPI Data Out (SPI mode). RC6 can also be the USART Asynchronous Transmit or Synchronous Clock. RC7 can also be the USART Asynchronous Receive or Synchronous Data. PORTD is a bi-directional I/O port or parallel slave port when interfacing to a microprocessor bus.
RD0/PSP0 RD1/PSP1 RD2/PSP2 RD3/PSP3 RD4/PSP4 RD5/PSP5 RD6/PSP6 RD7/PSP7
19 20 21 22 27 28 29 30
21 22 23 24 30 31 32 33
38 39 40 41 2 3 4 5
I/O I/O I/O I/O I/O I/O I/O I/O
ST/TTL(3) ST/TTL(3) ST/TTL(3) ST/TTL(3) ST/TTL(3) ST/TTL(3) ST/TTL(3) ST/TTL(3) PORTE is a bi-directional I/O port. ST/TTL(3) ST/TTL(3) ST/TTL(3) -- -- --
RE0/RD/AN5
(5)
8 9 10 12,31 11,32 --
9 10 11 13,34 12,35 1,17,28, 40
25 26 27 6,29 7,28 12,13, 33,34
I/O I/O I/O P P
RE0 can also be read control for the parallel slave port, or analog input 5(5). RE1 can also be write control for the parallel slave port, or analog input 6(5). RE2 can also be select control for the parallel slave port, or analog input 7(5). Ground reference for logic and I/O pins. Positive supply for logic and I/O pins. These pins are not internally connected. These pins should be left unconnected.
RE1/WR/AN6(5) RE2/CS/AN7(5) VSS VDD NC
Legend: I = input O = output I/O = input/output P = power -- = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. 3: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel Slave Port mode (for interfacing to a microprocessor bus). 4: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. 5: A/D is not available on the PIC16C65B.
2000 Microchip Technology Inc.
DS30605C-page 13
PIC16C63A/65B/73B/74B
3.1 Clocking Scheme/Instruction Cycle 3.2 Instruction Flow/Pipelining
An "Instruction Cycle" consists of four Q cycles (Q1, Q2, Q3 and Q4). The instruction fetch and execute are pipelined such that fetch takes one instruction cycle, while decode and execute takes another instruction cycle. However, due to the pipelining, each instruction effectively executes in one cycle. If an instruction causes the program counter to change (e.g., GOTO), then two cycles are required to complete the instruction (Example 3-1). A fetch cycle begins with the program counter (PC) incrementing in Q1. In the execution cycle, the fetched instruction is latched into the "Instruction Register" (IR) in cycle Q1. This instruction is then decoded and executed during the Q2, Q3 and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write).
The clock input (from OSC1) is internally divided by four to generate four non-overlapping quadrature clocks, namely Q1, Q2, Q3 and Q4. Internally, the program counter (PC) is incremented every Q1, the instruction is fetched from the program memory and latched into the instruction register in Q4. The instruction is decoded and executed during the following Q1 through Q4. The clocks and instruction execution flow is shown in Figure 3-2.
FIGURE 3-2:
CLOCK/INSTRUCTION CYCLE
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1 Q1 Q2 Q3 Q4 PC OSC2/CLKOUT (RC mode)
PC PC+1 PC+2
Internal phase clock
Fetch INST (PC) Execute INST (PC-1)
Fetch INST (PC+1) Execute INST (PC)
Fetch INST (PC+2) Execute INST (PC+1)
EXAMPLE 3-1:
INSTRUCTION PIPELINE FLOW
TCY0 TCY1 Execute 1 Fetch 2 Execute 2 Fetch 3 Execute 3 Fetch 4 Flush Fetch SUB_1 Execute SUB_1 TCY2 TCY3 TCY4 TCY5
1. MOVLW 55h 2. MOVWF PORTB 3. CALL 4. BSF SUB_1
Fetch 1
PORTA, BIT3 (Forced NOP)
5. Instruction @ address SUB_1
Note:
All instructions are single cycle, except for any program branches. These take two cycles, since the fetch instruction is "flushed" from the pipeline, while the new instruction is being fetched and then executed.
DS30605C-page 14
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.0
4.1
MEMORY ORGANIZATION
Program Memory Organization
4.2
Data Memory Organization
The PIC16C63A/65B/73B/74B has a 13-bit program counter capable of addressing an 8K x 14 program memory space. All devices covered by this data sheet have 4K x 14 bits of program memory. The address range is 0000h - 0FFFh for all devices. Accessing a location above 0FFFh will cause a wraparound. The RESET vector is at 0000h and the interrupt vector is at 0004h.
The data memory is partitioned into multiple banks which contain the General Purpose Registers (GPR) and the Special Function Registers (SFR). Bits RP1 and RP0 are the bank select bits. RP1:RP0 (STATUS<6:5>) = 00 Bank0 = 01 Bank1 = 10 Bank2 = 11 Bank3 Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the SFRs. Above the SFRs are GPRs, implemented as static RAM. All implemented banks contain SFRs. Frequently used SFRs from one bank may be mirrored in another bank for code reduction and quicker access. Note: Maintain the IRP and RP1 bits clear in these devices.
FIGURE 4-1:
PIC16C63A/65B/73B/74B PROGRAM MEMORY MAP AND STACK
PC<12:0>
CALL,RETURN RETFIE,RETLW
13
4.2.1
Stack Level 1
GENERAL PURPOSE REGISTER FILE
Stack Level 8 RESET Vector
The register file can be accessed either directly, or indirectly, through the File Select Register (FSR) (Section 4.5). 0000h
User Memory Space
Interrupt Vector On-chip Program Memory (Page 0)
0004h 0005h 07FFh
On-chip Program Memory (Page 1)
0800h
0FFFh 1000h
1FFFh
2000 Microchip Technology Inc.
DS30605C-page 15
PIC16C63A/65B/73B/74B
FIGURE 4-2:
File Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h INDF(1) TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTD(2) PORTE(2) PCLATH INTCON PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES(3) ADCON0(3)
REGISTER FILE MAP
File Address INDF(1) OPTION_REG PCL STATUS FSR TRISA TRISB TRISC TRISD(2) TRISE(2) PCLATH INTCON PIE1 PIE2 PCON 80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h
4.2.2
SPECIAL FUNCTION REGISTERS
The Special Function Registers are registers used by the CPU and Peripheral Modules for controlling the desired operation of the device. These registers are implemented as static RAM. The Special Function Registers can be classified into two sets (core and peripheral). Those registers associated with the "core" functions are described in this section, and those related to the operation of the peripheral features are described in the section of that peripheral feature.
PR2 SSPADD SSPSTAT
TXSTA SPBRG
ADCON1(3)
General Purpose Register
General Purpose Register
7Fh Bank 0 Bank 1
FFh
Unimplemented data memory locations, read as '0'.
Note 1: Not a physical register. 2: These registers are not implemented on the PIC16C63A/73B, read as '0'. 3: These registers are not implemented on the PIC16C63A/65B, read as '0'.
DS30605C-page 16
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 4-1:
Address Name
SPECIAL FUNCTION REGISTER SUMMARY
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other RESETS(3)
Bank 0 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh INDF(4) TMR0 PCL(4) STATUS FSR(4) PORTA PORTB PORTC PORTD(5) PORTE(5) PCLATH(1,4) INTCON(4) PIR1 PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES(6) ADCON0
(6) (4)
Addressing this location uses contents of FSR to address data memory (not a physical register) Timer0 module's register Program Counter's (PC) Least Significant Byte IRP
(2)
0000 0000 0000 0000 xxxx xxxx uuuu uuuu 0000 0000 0000 0000
RP1
(2)
RP0
TO
PD
Z
DC
C
0001 1xxx 000q quuu xxxx xxxx uuuu uuuu --0x 0000 --0u 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
Indirect data memory address pointer -- -- PORTA Data Latch when written: PORTA pins when read
PORTB Data Latch when written: PORTB pins when read PORTC Data Latch when written: PORTC pins when read PORTD Data Latch when written: PORTD pins when read -- -- GIE PSPIF(5) -- -- -- PEIE ADIF(6) -- -- -- T0IE RCIF -- -- -- RE2 RE1 RE0
---- -xxx ---- -uuu ---0 0000 ---0 0000 0000 000x 0000 000u 0000 0000 0000 0000 ---- ---0 ---- ---0 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
Write Buffer for the upper 5 bits of the Program Counter INTE TXIF - RBIE SSPIF -- T0IF CCP1IF -- INTF TMR2IF -- RBIF TMR1IF CCP2IF
Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS
TMR1ON --00 0000 --uu uuuu
0000 0000 0000 0000
Timer2 module's register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON
T2CKPS1 T2CKPS0 -000 0000 -000 0000
xxxx xxxx uuuu uuuu
Synchronous Serial Port Receive Buffer/Transmit Register WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0
0000 0000 0000 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
Capture/Compare/PWM Register1 (LSB) Capture/Compare/PWM Register1 (MSB) -- SPEN -- RX9 CCP1X SREN CCP1Y CREN CCP1M3 -- CCP1M2 FERR CCP1M1 OERR
CCP1M0 --00 0000 --00 0000 RX9D
0000 -00x 0000 -00x 0000 0000 0000 0000 0000 0000 0000 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
USART Transmit Data register USART Receive Data register Capture/Compare/PWM Register2 (LSB) Capture/Compare/PWM Register2 (MSB) -- -- CCP2X CCP2Y CCP2M3 CCP2M2 CCP2M1
CCP2M0 --00 0000 --00 0000
xxxx xxxx uuuu uuuu
A/D Result register ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE -- ADON
0000 00-0 0000 00-0
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0'. Shaded locations are unimplemented, read as `0'. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8>. 2: The IRP and RP1 bits are reserved; always maintain these bits clear. 3: Other (non power-up) RESETS include external RESET through MCLR and Watchdog Timer Reset. 4: These registers can be addressed from either bank. 5: PORTD, PORTE and the parallel slave port are not implemented on the PIC16C63A/73B; always maintain these bits and registers clear. 6: The A/D is not implemented on the PIC16C63A/65B; always maintain these bits and registers clear.
2000 Microchip Technology Inc.
DS30605C-page 17
PIC16C63A/65B/73B/74B
TABLE 4-1:
Address Name
SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other RESETS(3)
Bank 1
80h 81h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh PR2 SSPADD SSPSTAT -- -- -- TXSTA SPBRG -- -- -- -- -- ADCON1
(6)
INDF(4) OPTION_REG PCL(4) STATUS FSR(4) TRISA TRISB TRISC TRISD(5) TRISE(5) PCLATH(1,4) INTCON(4) PIE1 PIE2 PCON -- -- --
(4)
Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0
0000 0000 0000 0000 1111 1111 1111 1111 0000 0000 0000 0000
Program Counter's (PC) Least Significant Byte IRP
(2)
RP1
(2)
RP0
TO
PD
Z
DC
C
0001 1xxx 000q quuu xxxx xxxx uuuu uuuu --11 1111 --11 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111
Indirect data memory address pointer -- -- PORTA Data Direction Register
PORTB Data Direction register PORTC Data Direction register PORTD Data Direction register IBF -- GIE PSPIE(5) -- -- OBF -- PEIE ADIE(6) -- -- IBOV -- T0IE RCIE -- -- PSPMODE -- PORTE Data Direction bits
0000 -111 0000 -111 ---0 0000 ---0 0000 0000 000x 0000 000u 0000 0000 0000 0000 ---- ---0 ---- ---0 ---- --qq ---- --uu
Write Buffer for the upper 5 bits of the Program Counter INTE TXIE -- -- RBIE SSPIE -- -- T0IF CCP1IE -- -- INTF TMR2IE -- POR RBIF TMR1IE CCP2IE BOR
Unimplemented Unimplemented Unimplemented Timer2 Period register Synchronous Serial Port (I2C mode) Address register -- -- D/A P S R/W UA BF
-- -- --
-- -- --
1111 1111 1111 1111 0000 0000 0000 0000 --00 0000 --00 0000
Unimplemented Unimplemented Unimplemented CSRC TX9 TXEN SYNC -- BRGH TRMT TX9D
-- -- --
-- -- --
0000 -010 0000 -010 0000 0000 0000 0000
Baud Rate Generator register Unimplemented Unimplemented Unimplemented Unimplemented Unimplemented -- -- -- -- -- PCFG2 PCFG1 PCFG0
-- -- -- -- --
-- -- -- -- --
---- -000 ---- -000
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0'. Shaded locations are unimplemented, read as `0'. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<12:8>. 2: The IRP and RP1 bits are reserved; always maintain these bits clear. 3: Other (non power-up) RESETS include external RESET through MCLR and Watchdog Timer Reset. 4: These registers can be addressed from either bank. 5: PORTD, PORTE and the parallel slave port are not implemented on the PIC16C63A/73B; always maintain these bits and registers clear. 6: The A/D is not implemented on the PIC16C63A/65B; always maintain these bits and registers clear.
DS30605C-page 18
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.2.2.1 STATUS Register
The STATUS register, shown in Register 4-1, contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory. The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will clear the upper three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). It is recommended that only BCF, BSF, SWAPF and MOVWF instructions be used to alter the STATUS register. These instructions do not affect the Z, C or DC bits in the STATUS register. For other instructions which do not affect status bits, see the "Instruction Set Summary." Note 1: These devices do not use bits IRP and RP1 (STATUS<7:6>), maintain these bits clear to ensure upward compatibility with future products. 2: The C and DC bits operate as borrow and digit borrow bits, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples.
REGISTER 4-1:
STATUS REGISTER (ADDRESS 03h, 83h)
R/W-0 IRP(1) bit 7 R/W-0 RP1(1) R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC R/W-x C(2) bit 0
bit 7
IRP(1): Register Bank Select bit (used for indirect addressing) 1 = Bank 2, 3 (100h - 1FFh) 0 = Bank 0, 1 (00h - FFh) RP1(1):RP0: Register Bank Select bits (used for direct addressing) 11 = Bank 3 (180h - 1FFh) 10 = Bank 2 (100h - 17Fh) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero DC: Digit carry/borrow bit (ADDWF,ADDLW,SUBLW,SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result C(2): Carry/borrow bit (ADDWF,ADDLW,SUBLW,SUBWF instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note 1: Maintain the IRP and RP1 bits clear. 2: For borrow and digit borrow, the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF,RLF) instructions, this bit is loaded with either the high or low order bit of the source register. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 6-5
bit 4
bit 3
bit 2
bit 1
bit 0
2000 Microchip Technology Inc.
DS30605C-page 19
PIC16C63A/65B/73B/74B
4.2.2.2 OPTION Register
Note: The OPTION_REG register is a readable and writable register, which contains various control bits to configure the TMR0/WDT prescaler, the external INT Interrupt, TMR0 and the weak pull-ups on PORTB. To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the watchdog timer.
REGISTER 4-2:
OPTION_REG REGISTER (ADDRESS 81h)
R/W-1 RBPU bit 7 R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0
bit 7
RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled by individual port latch values INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module PS2:PS0: Prescaler Rate Select bits
Bit Value 000 001 010 011 100 101 110 111 TMR0 Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 WDT Rate 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128
bit 6
bit 5
bit 4
bit 3
bit 2-0
Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
DS30605C-page 20
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.2.2.3 INTCON Register
Note: The INTCON register is a readable and writable register, which contains various enable and flag bits for the TMR0 register overflow, RB Port change and external RB0/INT pin interrupts. Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit, or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 4-3:
INTCON REGISTER (ADDRESS 0Bh, 8Bh)
R/W-0 GIE bit 7 R/W-0 PEIE R/W-0 T0IE R/W-0 INTE R/W-0 RBIE R/W-0 T0IF R/W-0 INTF R/W-x RBIF bit 0
bit 7
GIE: Global Interrupt Enable bit 1 = Enables all unmasked interrupts 0 = Disables all interrupts PEIE: Peripheral Interrupt Enable bit 1 = Enables all unmasked peripheral interrupts 0 = Disables all peripheral interrupts T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt INTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state(1) 0 = None of the RB7:RB4 pins have changed state Note 1: A mismatch condition will exist until PORTB is read. After reading PORTB, the RBIF flag bit can be cleared. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2000 Microchip Technology Inc.
DS30605C-page 21
PIC16C63A/65B/73B/74B
4.2.2.4 PIE1 Register
Note: This register contains the individual enable bits for the peripheral interrupts. Bit PEIE (INTCON<6>) must be set to enable any peripheral interrupt.
REGISTER 4-4:
PIE1 REGISTER (ADDRESS 8Ch)
R/W-0 PSPIE(1) bit 7 R/W-0 ADIE(2) R/W-0 RCIE R/W-0 TXIE R/W-0 SSPIE R/W-0 CCP1IE R/W-0 TMR2IE R/W-0 TMR1IE bit 0
bit 7
PSPIE(1): Parallel Slave Port Read/Write Interrupt Enable bit 1 = Enables the PSP read/write interrupt 0 = Disables the PSP read/write interrupt ADIE(2): A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt RCIE: USART Receive Interrupt Enable bit 1 = Enables the USART receive interrupt 0 = Disables the USART receive interrupt TXIE: USART Transmit Interrupt Enable bit 1 = Enables the USART transmit interrupt 0 = Disables the USART transmit interrupt SSPIE: Synchronous Serial Port Interrupt Enable bit 1 = Enables the SSP interrupt 0 = Disables the SSP interrupt CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt Note 1: PIC16C63A/73B devices do not have a parallel slave port implemented; always maintain this bit clear. 2: PIC16C63A/65B devices do not have an A/D implemented; always maintain this bit clear. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
DS30605C-page 22
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.2.2.5 PIR1 Register
Note: This register contains the individual flag bits for the peripheral interrupts. Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit, or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 4-5:
PIR1 REGISTER (ADDRESS 0Ch)
R/W-0 PSPIF(1) bit 7 R/W-0 ADIF(2) R-0 RCIF R-0 TXIF R/W-0 SSPIF R/W-0 CCP1IF R/W-0 TMR2IF R/W-0 TMR1IF bit 0
bit 7
PSPIF(1): Parallel Slave Port Read/Write Interrupt Flag bit 1 = A read or a write operation has taken place (must be cleared in software) 0 = No read or write has occurred ADIF(2): A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete RCIF: USART Receive Interrupt Flag bit 1 = The USART receive buffer is full (clear by reading RCREG) 0 = The USART receive buffer is empty TXIF: USART Transmit Interrupt Flag bit 1 = The USART transmit buffer is empty (clear by writing to TXREG) 0 = The USART transmit buffer is full SSPIF: Synchronous Serial Port Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive CCP1IF: CCP1 Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused in this mode TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow Note 1: PIC16C63A/73B devices do not have a parallel slave port implemented. This bit location is reserved on these devices. 2: PIC16C63A/65B devices do not have an A/D implemented. This bit location is reserved on these devices. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
2000 Microchip Technology Inc.
DS30605C-page 23
PIC16C63A/65B/73B/74B
4.2.2.6 PIE2 Register
This register contains the individual enable bit for the CCP2 peripheral interrupt.
REGISTER 4-6:
PIE2 REGISTER (ADDRESS 8Dh)
U-0 -- bit 7 U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 CCP2IE bit 0
bit 7-1 bit 0
Unimplemented: Read as '0' CCP2IE: CCP2 Interrupt Enable bit 1 = Enables the CCP2 interrupt 0 = Disables the CCP2 interrupt Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
4.2.2.7
PIR2 Register
Note:
This register contains the CCP2 interrupt flag bit.
Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit, or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 4-7:
PIR2 REGISTER (ADDRESS 0Dh)
U-0 -- bit 7 U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 CCP2IF bit 0
bit 7-1 bit 0
Unimplemented: Read as '0' CCP2IF: CCP2 Interrupt Flag bit Capture mode: 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare mode: 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM mode: Unused Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
DS30605C-page 24
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.2.2.8 PCON Register
Note: The Power Control (PCON) register contains flag bits to allow differentiation between a Power-on Reset (POR), a Brown-out Reset (BOR), a Watchdog Reset (WDT) and an external MCLR Reset. BOR is unknown on POR. It must be set by the user and checked on subsequent RESETS to see if BOR is clear, indicating a brown-out has occurred. The BOR status bit is a "don't care" and is not predictable if the brown-out circuit is disabled (by clearing the BODEN bit in the configuration word).
REGISTER 4-8:
PCON REGISTER (ADDRESS 8Eh)
U-0 -- bit 7 U-0 -- U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 POR R/W-q BOR bit 0
bit 7-2 bit 1
Unimplemented: Read as '0' POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 0
2000 Microchip Technology Inc.
DS30605C-page 25
PIC16C63A/65B/73B/74B
4.3 PCL and PCLATH
The program counter (PC) is 13-bits wide. The low byte comes from the PCL register, which is a readable and writable register. The upper bits (PC<12:8>) are not readable, but are indirectly writable through the PCLATH register. On any RESET, the upper bits of the PC will be cleared. Figure 4-3 shows the two situations for the loading of the PC. The upper example in the figure shows how the PC is loaded on a write to PCL (PCLATH<4:0> PCH). The lower example in the figure shows how the PC is loaded during a CALL or GOTO instruction (PCLATH<4:3> PCH). Note 1: There are no status bits to indicate stack overflow or stack underflow conditions. 2: There are no instructions/mnemonics called PUSH or POP. These are actions that occur from the execution of the CALL, RETURN, RETLW, and RETFIE instructions, or the vectoring to an interrupt address.
4.4
Program Memory Paging
FIGURE 4-3:
LOADING OF PC IN DIFFERENT SITUATIONS
PCL 8 7 0 Instruction with PCL as Destination ALU
PCH 12 PC 5
PCLATH<4:0>
8
PCLATH PCH 12 PC 2 PCLATH<4:3> 11 Opcode <10:0> PCLATH 11 10 8 7 PCL 0
GOTO,CALL
PIC16CXX devices are capable of addressing a continuous 8K word block of program memory. The CALL and GOTO instructions provide only 11 bits of address to allow branching within any 2K program memory page. When executing a CALL or GOTO instruction, the upper 2 bits of the address are provided by PCLATH<4:3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bits are programmed, so that the desired program memory page is addressed. If a return from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is popped from the stack. Therefore, manipulation of the PCLATH<4:3> bits are not required for the return instructions (which POPs the address from the stack). Note 1: The contents of PCLATH are unchanged after a return or RETFIE instruction is executed. The user must set up PCLATH for any subsequent CALL's or GOTO's 2: PCLATH<4> is not used in these PICmicro(R) devices. The use of PCLATH<4> as a general purpose read/ write bit is not recommended, since this may affect upward compatibility with future products. Example 4-1 shows the calling of a subroutine in page 1 of the program memory. This example assumes that PCLATH is saved and restored by the Interrupt Service Routine (if interrupts are used).
4.3.1
COMPUTED GOTO
A computed GOTO is accomplished by adding an offset to the program counter (ADDWF PCL). When doing a table read using a computed GOTO method, care should be exercised if the table location crosses a PCL memory boundary (each 256 byte block). Refer to the application note "Implementing a Table Read" (AN556).
EXAMPLE 4-1:
ORG 0x500 BSF PCLATH,3 CALL SUB1_P1 : : ORG 0x900 SUB1_P1 : : : RETURN
4.3.2
STACK
CALL OF A SUBROUTINE IN PAGE 1 FROM PAGE 0
;Select page 1 (800h-FFFh) ;Call subroutine in ;page 1 (800h-FFFh) ;page 1 (800h-FFFh) ;called subroutine ;page 1 (800h-FFFh) ;return to Call subroutine ;in page 0 (000h-7FFh)
The PIC16CXX family has an 8-level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed, or an interrupt causes a branch. The stack is POPed in the event of a RETURN,RETLW or a RETFIE instruction execution. PCLATH is not affected by a PUSH or POP operation. The stack operates as a circular buffer. This means that after the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on).
DS30605C-page 26
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
4.5 Indirect Addressing, INDF and FSR Registers
EXAMPLE 4-2:
movlw movwf clrf incf btfss goto :
INDIRECT ADDRESSING
0x20 FSR INDF FSR,F FSR,4 NEXT ;initialize pointer ;to RAM ;clear INDF register ;inc pointer ;all done? ;no clear next ;yes continue
The INDF register is not a physical register. Addressing the INDF register will cause indirect addressing. Indirect addressing is possible by using the INDF register. Any instruction using the INDF register actually accesses the register pointed to by the File Select Register, FSR. Reading the INDF register itself indirectly (FSR = '0') will read 00h. Writing to the INDF register indirectly results in a no-operation (although status bits may be affected). An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit (STATUS<7>), as shown in Figure 4-4. A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 4-2.
NEXT
CONTINUE
Note:
Maintain the IRP and RP1 bits clear.
FIGURE 4-4:
DIRECT/INDIRECT ADDRESSING
Direct Addressing Indirect Addressing
0 IRP 0 location select 00 00h 01 80h 10 100h 11 180h bank select location select 7 FSR register 0
RP1:RP0 0 bank select
6
from opcode
not used Data Memory
7Fh
FFh
17Fh
1FFh
Bank 0
Bank 1
Bank 2
Bank 3
Note 1: For register file map detail, see Figure 4-2. 2: Shaded portions are not implemented; maintain the IRP and RP1 bits clear.
2000 Microchip Technology Inc.
DS30605C-page 27
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 28
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
5.0 I/O PORTS
FIGURE 5-1:
Data Bus WR Port
Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin.
BLOCK DIAGRAM OF RA3:RA0 AND RA5 PINS
Q VDD
D
5.1
PORTA and TRISA Registers
CK
Q
P I/O pin(1)
PORTA is a 6-bit latch. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. All pins have data direction bits (TRIS registers), which can configure these pins as output or input. Setting a TRISA register bit puts the corresponding output driver in a hi-impedance mode. Clearing a bit in the TRISA register puts the contents of the output latch on the selected pin(s). Reading the PORTA register reads the status of the pins, whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, the value is modified and then written to the port data latch. Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. On the PIC16C73B/74B, PORTA pins are multiplexed with analog inputs and analog VREF input. The operation of each pin is selected by clearing/setting the control bits in the ADCON1 register (A/D Control Register1). Note: On all RESETS, pins with analog functions are configured as analog and digital inputs.
RD Port
Data Latch D WR TRIS Q N
CK
Q
TRIS Latch
VSS Analog Input mode
RD TRIS Q D
TTL Input Buffer
EN
To A/D Converter
Note 1: I/O pins have protection diodes to VDD and VSS.
FIGURE 5-2:
Data Bus WR Port
BLOCK DIAGRAM OF RA4/T0CKI PIN
D Q Q
The TRISA register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs.
CK
EXAMPLE 5-1:
BCF CLRF STATUS, RP0 PORTA
INITIALIZING PORTA (PIC16C73B/74B)
; ; ; ; ; ; ; ; ; ; ; ; ; ;
Data Latch
D Q Q
N VSS Schmitt Trigger Input Buffer
I/O pin (1)
WR TRIS
Initialize PORTA by clearing output data latches Select Bank 1 Configure all pins as digital inputs Value used to initialize data direction Set RA<3:0> as inputs RA<5:4> as outputs TRISA<7:6> are always read as '0'.
CK
TRIS Latch
BSF MOVLW MOVWF MOVLW
STATUS, RP0 0x06 ADCON1 0xCF
RD TRIS
Q D EN EN
MOVWF
TRISA
RD Port TMR0 Clock Input Note 1: I/O pins have protection diodes to VDD and VSS.
2000 Microchip Technology Inc.
DS30605C-page 29
PIC16C63A/65B/73B/74B
TABLE 5-1:
Name RA0/AN0(1) RA1/AN1(1) RA2/AN2(1) RA3/AN3/VREF(1) RA4/T0CKI RA5/SS/AN4(1)
PORTA FUNCTIONS
Bit# bit0 bit1 bit2 bit3 bit4 bit5 Buffer TTL TTL TTL TTL ST TTL Function Digital input/output or analog input. Digital input/output or analog input. Digital input/output or analog input. Digital input/output or analog input or VREF. Digital input/output or external clock input for Timer0. Output is open drain type. Input/output or slave select input for synchronous serial port or analog input.
Legend: TTL = TTL input, ST = Schmitt Trigger input Note 1: The A/D is not implemented on the PIC16C63A/65B. Pins will operate as digital I/O only. ADCON1 is not implemented; maintain this register clear.
TABLE 5-2:
Address 05h 85h 9Fh
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Bit 7 -- -- -- Bit 6 -- -- -- Bit 5 RA5 Bit 4 RA4 Bit 3 RA3 Bit 2 RA2 Bit 1 RA1 Bit 0 RA0 Value on: POR, BOR
--0x 0000 --11 1111
Name PORTA TRISA ADCON1(1)
Value on all other RESETS
--0u 0000 --11 1111 ---- -000
PORTA Data Direction Register -- -- -- PCFG2 PCFG1 PCFG0
---- -000
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by PORTA. Note 1: The A/D is not implemented on the PIC16C63A/65B. Pins will operate as digital I/O only. ADCON1 is not implemented; maintain this register clear.
DS30605C-page 30
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
5.2 PORTB and TRISB Registers
PORTB is an 8-bit wide, bi-directional port. The corresponding data direction register is TRISB. Setting a bit in the TRISB register puts the corresponding output driver in a hi-impedance input mode. Clearing a bit in the TRISB register puts the contents of the output latch on the selected pin(s). Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION_REG<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. This interrupt can wake the device from SLEEP. The user, in the Interrupt Service Routine, can clear the interrupt in the following manner: a) b) Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF.
A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition, and allow flag bit RBIF to be cleared. This interrupt-on-mismatch feature, together with software configurable pull-ups on these four pins, allow easy interface to a keypad and make it possible for wake-up on key depression. Refer to the Embedded Control Handbook, "Implementing Wake-up on Key Stroke" (AN552). The interrupt-on-change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt-on-change feature. Polling of PORTB is not recommended while using the interrupt-on-change feature. RB0/INT is an external interrupt input pin and is configured using the INTEDG bit (OPTION_REG<6>). RB0/INT is discussed in detail in Section 13.5.1.
FIGURE 5-3:
BLOCK DIAGRAM OF RB3:RB0 PINS
VDD Weak
RBPU(2) Data Latch Data Bus WR Port D CK TRIS Latch D WR TRIS CK Q TTL Input Buffer Q
P Pull-up
I/O pin(1)
FIGURE 5-4:
BLOCK DIAGRAM OF RB7:RB4 PINS
VDD
P Pull-up
RBPU(2) RD TRIS Q RD Port D EN Data Bus WR Port Data Latch D Q
Weak
I/O pin(1) CK TRIS Latch D Q
RB0/INT Schmitt Trigger Buffer Note RD Port WR TRIS
CK
1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). RD TRIS Q RD Port Set RBIF
TTL Input Buffer
ST Buffer
Four of PORTB's pins, RB7:RB4, have an interrupt-on-change feature. Only pins configured as inputs can cause this interrupt to occur (i.e., any RB7:RB4 pin configured as an output is excluded from the interrupt-on-change comparison). The input pins (of RB7:RB4) are compared with the value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are OR'd together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>).
Latch D EN Q1
From other RB7:RB4 pins
Q
D RD Port EN Q3
RB7:RB6 in Serial Programming mode Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>).
2000 Microchip Technology Inc.
DS30605C-page 31
PIC16C63A/65B/73B/74B
TABLE 5-3:
Name RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7
PORTB FUNCTIONS
Bit# bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Buffer TTL/ST(1) TTL TTL TTL TTL TTL TTL/ST(2) TTL/ST(2) Function Input/output pin or external interrupt input. Internal software programmable weak pull-up. Input/output pin. Internal software programmable weak pull-up. Input/output pin. Internal software programmable weak pull-up. Input/output pin. Internal software programmable weak pull-up. Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. Serial programming clock. Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. Serial programming data.
Legend: TTL = TTL input, ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.
TABLE 5-4:
Address 06h 86h 81h
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Name Bit 7 RB7 Bit 6 RB6 Bit 5 RB5 Bit 4 RB4 Bit 3 RB3 Bit 2 RB2 Bit 1 RB1 Bit 0 RB0 Value on: POR, BOR
xxxx xxxx 1111 1111
Value on all other RESETS
uuuu uuuu 1111 1111 1111 1111
PORTB TRISB OPTION_REG
PORTB Data Direction register RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0
1111 1111
Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB.
DS30605C-page 32
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
5.3 PORTC and TRISC Registers
FIGURE 5-5: PORTC BLOCK DIAGRAM
PORTC is an 8-bit bi-directional port. Each pin is individually configurable as an input or output through the TRISC register. PORTC is multiplexed with several peripheral functions (Table 5-5). PORTC pins have Schmitt Trigger input buffers. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Since the TRIS bit override is in effect while the peripheral is enabled, read-modify-write instructions (BSF, BCF, XORWF) with TRISC as destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings.
PORT/PERIPHERAL Select(2) Peripheral Data Out Data Bus WR Port 0 D CK Q Q 1 I/O pin(1) VDD P Data Latch WR TRIS D CK Q Q N VSS RD TRIS Peripheral OE(3) Q D EN Schmitt Trigger
TRIS Latch
RD Port Peripheral Input Note
1: I/O pins have diode protection to VDD and VSS. 2: Port/Peripheral select signal selects between port data and peripheral output. 3: Peripheral OE (output enable) is only activated if peripheral select is active.
TABLE 5-5:
Name
PORTC FUNCTIONS
Bit# Buffer Type Function
RC0/T1OSO/T1CKI RC1/T1OSI/CCP2 RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6/TX/CK RC7/RX/DT
bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7
ST ST ST ST ST ST ST ST
Input/output port pin or Timer1 oscillator output/Timer1 clock input. Input/output port pin or Timer1 oscillator input or Capture2 input/Compare2 output/PWM2 output. Input/output port pin or Capture1 input/Compare1 output/PWM1 output. RC3 can also be the Synchronous Serial Clock for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or Data I/O (I2C mode). Input/output port pin or Synchronous Serial Port Data output. Input/output port pin or USART Asynchronous Transmit, or USART Synchronous Clock. Input/output port pin or USART Asynchronous Receive, or USART Synchronous Data.
Legend: ST = Schmitt Trigger input
TABLE 5-6:
Address 07h 87h Name PORTC TRISC
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Bit 7 RC7 Bit 6 RC6 Bit 5 RC5 Bit 4 RC4 Bit 3 RC3 Bit 2 RC2 Bit 1 RC1 Bit 0 RC0
Value on: POR, BOR xxxx xxxx 1111 1111 Value on all other RESETS uuuu uuuu 1111 1111
PORTC Data Direction register
Legend: x = unknown, u = unchanged
2000 Microchip Technology Inc.
DS30605C-page 33
PIC16C63A/65B/73B/74B
5.4
Note:
PORTD and TRISD Registers
The PIC16C63A and PIC16C73B do not provide PORTD. The PORTD and TRISD registers are not implemented.
FIGURE 5-6:
Data Bus WR Port
D
PORTD BLOCK DIAGRAM
Q
I/O pin(1)
CK
PORTD is an 8-bit port with Schmitt Trigger input buffers. Each pin is individually configured as an input or output. PORTD can be configured as an 8-bit wide microprocessor port (parallel slave port) by setting control bit PSPMODE (TRISE<4>). In this mode, the input buffers are TTL.
WR TRIS
Data Latch
D Q
CK
TRIS Latch
Schmitt Trigger Input Buffer
RD TRIS
Q D EN EN
RD Port
Note 1: I/O pins have protection diodes to VDD and VSS.
TABLE 5-7:
Name RD0/PSP0 RD1/PSP1 RD2/PSP2 RD3/PSP3 RD4/PSP4 RD5/PSP5 RD6/PSP6 RD7/PSP7
PORTD FUNCTIONS
Bit# bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Buffer Type ST/TTL(1) ST/TTL ST/TTL ST/TTL
(1) (1) (1)
Function Input/output port pin or parallel slave port bit0 Input/output port pin or parallel slave port bit1 Input/output port pin or parallel slave port bit2 Input/output port pin or parallel slave port bit3 Input/output port pin or parallel slave port bit4 Input/output port pin or parallel slave port bit5 Input/output port pin or parallel slave port bit6 Input/output port pin or parallel slave port bit7
ST/TTL(1) ST/TTL ST/TTL ST/TTL
(1) (1) (1)
Legend: ST = Schmitt Trigger input, TTL = TTL input Note 1: Input buffers are Schmitt Triggers when in I/O mode and TTL buffer when in Parallel Slave Port mode.
TABLE 5-8:
Address 08h 88h 89h Name PORTD TRISD TRISE
SUMMARY OF REGISTERS ASSOCIATED WITH PORTD
Bit 7 RD7 Bit 6 RD6 Bit 5 RD5 Bit 4 RD4 Bit 3 RD3 Bit 2 RD2 Bit 1 RD1 Bit 0 RD0
Value on: POR, BOR xxxx xxxx 1111 1111 Value on all other RESETS uuuu uuuu 1111 1111 0000 -111
PORTD Data Direction register IBF OBF IBOV PSPMODE -- PORTE Data Direction bits
0000 -111
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by PORTD.
DS30605C-page 34
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
5.5 PORTE and TRISE Register
FIGURE 5-7:
Data Bus WR Port
D Q
PORTE BLOCK DIAGRAM
Note 1: The PIC16C63A and PIC16C73B do not provide PORTE. The PORTE and TRISE registers are not implemented. 2: The PIC16C63A/65B does not provide an A/D module. A/D functions are not implemented. PORTE has three pins: RE0/RD/AN5, RE1/WR/AN6 and RE2/CS/AN7, which are individually configured as inputs or outputs. These pins have Schmitt Trigger input buffers. I/O PORTE becomes control inputs for the microprocessor port when bit PSPMODE (TRISE<4>) is set. In this mode, the user must make sure that the TRISE<2:0> bits are set (pins are configured as digital inputs) and that register ADCON1 is configured for digital I/O. In this mode, the input buffers are TTL. Register 5-1 shows the TRISE register, which also controls the parallel slave port operation. PORTE pins may be multiplexed with analog inputs (PIC16C74B only). The operation of these pins is selected by control bits in the ADCON1 register. When selected as an analog input, these pins will read as '0's. TRISE controls the direction of the RE pins, even when they are being used as analog inputs. The user must make sure to keep the pins configured as inputs when using them as analog inputs. Note: On a Power-on Reset, these pins are configured as analog inputs and read as `0's.
I/O pin(1)
CK
Data Latch
D Q
WR TRIS
CK
TRIS Latch
Schmitt Trigger Input Buffer
RD TRIS
Q D EN EN
RD Port
Note 1: I/O pins have protection diodes to VDD and VSS.
TABLE 5-9:
Name RE0/RD/AN5
PORTE FUNCTIONS
Bit# bit0 Buffer Type ST/TTL
(1)
Function Input/output port pin or read control input in Parallel Slave Port mode or analog input: RD 1 = Idle 0 = Read operation. Contents of PORTD register is output to PORTD I/O pins (if chip selected). Input/output port pin or write control input in Parallel Slave Port mode or analog input: WR 1 = Idle 0 = Write operation. Value of PORTD I/O pins is latched into PORTD register (if chip selected). Input/output port pin or chip select control input in Parallel Slave Port mode or analog input: CS 1 = Device is not selected 0 = Device is selected
RE1/WR/AN6
bit1
ST/TTL(1)
RE2/CS/AN7
bit2
ST/TTL(1)
Legend: ST = Schmitt Trigger input, TTL = TTL input Note 1: Input buffers are Schmitt Triggers when in I/O mode and TTL buffers when in Parallel Slave Port mode.
2000 Microchip Technology Inc.
DS30605C-page 35
PIC16C63A/65B/73B/74B
REGISTER 5-1: TRISE REGISTER (ADDRESS 89h)
R-0 IBF bit 7 bit 7 IBF: Input Buffer Full Status bit 1 = A word has been received and is waiting to be read by the CPU 0 = No word has been received OBF: Output Buffer Full Status bit 1 = The output buffer still holds a previously written word 0 = The output buffer has been read IBOV: Input Buffer Overflow Detect bit (in Microprocessor mode) 1 = A write occurred when a previously input word has not been read (must be cleared in software) 0 = No overflow occurred PSPMODE: Parallel Slave Port Mode Select bit 1 = Parallel Slave Port mode 0 = General purpose I/O mode Unimplemented: Read as '0' TRISE2: Direction Control bit for pin RE2/CS/AN7 1 = Input 0 = Output TRISE1: Direction Control bit for pin RE1/WR/AN6 1 = Input 0 = Output TRISE0: Direction Control bit for pin RE0/RD/AN5 1 = Input 0 = Output Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown R-0 OBF R/W-0 IBOV R/W-0 PSPMODE U-0 -- R/W-1 TRISE2 R/W-1 TRISE1 R/W-1 TRISE0 bit 0
bit 6
bit 5
bit 4
bit 3 bit 2
bit 1
bit 0
TABLE 5-10:
Address 09h 89h 9Fh Name PORTE TRISE
SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
Bit 7 -- IBF -- Bit 6 -- OBF -- Bit 5 -- IBOV -- Bit 4 -- PSPMODE -- Bit 3 -- -- -- Bit 2 RE2 Bit 1 RE1 Bit 0 RE0
Value on: POR, BOR ---- -xxx 0000 -111 ---- -000 Value on all other RESETS ---- -uuu 0000 -111 ---- -000
PORTE Data Direction bits PCFG2 PCFG1 PCFG0
ADCON1
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by PORTE.
DS30605C-page 36
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
5.6
Note:
Parallel Slave Port (PSP)
The PIC16C63A and PIC16C73B do not provide a parallel slave port. The PORTD, PORTE, TRISD and TRISE registers are not implemented.
When not in PSP mode, the IBF and OBF bits are held clear. However, if flag bit IBOV was previously set, it must be cleared in firmware. An interrupt is generated and latched into flag bit PSPIF when a read or write operation is completed. PSPIF must be cleared by the user in firmware and the interrupt can be disabled by clearing the interrupt enable bit PSPIE (PIE1<7>).
PORTD operates as an 8-bit wide Parallel Slave Port (PSP), or microprocessor port when control bit PSPMODE (TRISE<4>) is set. In Slave mode, it is asynchronously readable and writable by the external world, through RD control input pin RE0/RD/AN5 and WR control input pin RE1/WR/AN6. It can directly interface to an 8-bit microprocessor data bus. The external microprocessor can read or write the PORTD latch as an 8-bit latch. Setting bit PSPMODE enables port pin RE0/RD/AN5 to be the RD input, RE1/WR/AN6 to be the WR input and RE2/CS/AN7 to be the CS (chip select) input. For this functionality, the corresponding data direction bits of the TRISE register (TRISE<2:0>) must be configured as inputs (set) and the A/D port configuration bits PCFG2:PCFG0 (ADCON1<2:0>) must be set, which will configure pins RE2:RE0 as digital I/O. There are actually two 8-bit latches, one for data out (from the PICmicro(R) MCU) and one for data input. The user writes 8-bit data to PORTD data latch and reads data from the port pin latch (note that they have the same address). In this mode, the TRISD register is ignored since the external device is controlling the direction of data flow. A write to the PSP occurs when both the CS and WR lines are first detected low. When either the CS or WR lines become high (level triggered), then the Input Buffer Full (IBF) status flag bit (TRISE<7>) is set on the Q4 clock cycle, following the next Q2 cycle, to signal the write is complete (Figure 5-9). The interrupt flag bit PSPIF (PIR1<7>) is also set on the same Q4 clock cycle. IBF can only be cleared by reading the PORTD input latch. The Input Buffer Overflow (IBOV) status flag bit (TRISE<5>) is set if a second write to the PSP is attempted when the previous byte has not been read out of the buffer. A read from the PSP occurs when both the CS and RD lines are first detected low. The Output Buffer Full (OBF) status flag bit (TRISE<6>) is cleared immediately (Figure 5-10), indicating that the PORTD latch is waiting to be read by the external bus. When either the CS or RD pin becomes high (level triggered), the interrupt flag bit PSPIF is set on the Q4 clock cycle, following the next Q2 cycle, indicating that the read is complete. OBF remains low until data is written to PORTD by the user firmware.
FIGURE 5-8:
PORTD AND PORTE BLOCK DIAGRAM (PARALLEL SLAVE PORT)
Data Bus WR Port
D
Q
CK
RDx pin TTL
Q
D EN EN
RD Port One bit of PORTD
Set Interrupt Flag PSPIF (PIR1<7>)
Read
TTL
RD CS WR
Chip Select
TTL
Write
TTL
Note 1: I/O pins have protection diodes to VDD and VSS.
2000 Microchip Technology Inc.
DS30605C-page 37
PIC16C63A/65B/73B/74B
FIGURE 5-9: PARALLEL SLAVE PORT WRITE WAVEFORMS
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
CS WR RD PORTD<7:0> IBF OBF PSPIF
FIGURE 5-10:
PARALLEL SLAVE PORT READ WAVEFORMS
Q1 CS WR RD PORTD<7:0> IBF OBF PSPIF
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
TABLE 5-11:
Address 08h 09h Name PORTD PORTE
REGISTERS ASSOCIATED WITH PARALLEL SLAVE PORT
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Value on: POR, BOR xxxx xxxx Value on all other RESETS uuuu uuuu ---- -uuu 0000 000u 0000 -111 0000 0000 0000 0000 ---- -000
Port data latch when written, Port pins when read -- GIE IBF PSPIF PSPIE -- -- PEIE OBF ADIF ADIE -- -- T0IE IBOV RCIF RCIE -- -- INTE PSPMODE TXIF TXIE -- -- RBIE -- SSPIF SSPIE -- RE2 T0IF RE1 INTF RE0 RBIF
---- -xxx 0000 000x 0000 -111 0000 0000 0000 0000 ---- -000
0Bh, 8Bh INTCON 89h 0Ch 8Ch 9Fh TRISE PIR1 PIE1 ADCON1
PORTE Data Direction Bits CCP1IF TMR2IF TMR1IF
CCP1IE TMR2IE TMR1IE PCFG2 PCFG1 PCFG0
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by the Parallel Slave Port.
DS30605C-page 38
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
6.0 TIMER0 MODULE
The Timer0 module timer/counter has the following features: * * * * * * 8-bit timer/counter Readable and writable 8-bit software programmable prescaler Internal or external clock select Interrupt on overflow from FFh to 00h Edge select for external clock Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In counter mode, Timer0 will increment, either on every rising, or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed in detail in Section 6.2. The prescaler is mutually exclusively shared between the Timer0 module and the watchdog timer. The prescaler is not readable or writable. Section 6.3 details the operation of the prescaler.
Figure 6-1 is a block diagram of the Timer0 module and the prescaler shared with the WDT. Additional information on the Timer0 module is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In Timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register.
6.1
Timer0 Interrupt
The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module Interrupt Service Routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP, since the timer is shut-off during SLEEP.
FIGURE 6-1:
CLKOUT (= FOSC/4)
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
Data Bus 8 1 0 M U X SYNC 2 Cycles TMR0 reg
0 RA4/T0CKI pin 1 T0SE
M U X
T0CS
PSA PRESCALER
Set Flag bit T0IF on Overflow
0 M U X
8-bit Prescaler 8 8 - to - 1MUX PS2:PS0
Watchdog Timer
1
PSA 0 MUX 1 PSA
WDT Enable bit
WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>).
2000 Microchip Technology Inc.
DS30605C-page 39
PIC16C63A/65B/73B/74B
6.2 Using Timer0 with an External Clock
module means that there is no prescaler for the Watchdog Timer, and vice-versa. This prescaler is not readable or writable (see Figure 6-1). The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g., CLRF 1, MOVWF 1, BSF 1,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the Watchdog Timer. The prescaler is not readable or writable. Note: Writing to TMR0, when the prescaler is assigned to Timer0, will clear the prescaler count, but will not change the prescaler assignment.
The synchronization of T0CKI with the internal phase clocks is accomplished by sampling the synchronized input on the Q2 and Q4 cycles of the internal phase clocks. Therefore, it is necessary for T0CKI to be high for at least 2 TOSC (and a small RC delay of 20 ns) and low for at least 2 TOSC (and a small RC delay of 20 ns). Refer to the electrical specification for the desired device.
6.3
Prescaler
There is only one prescaler available which is mutually exclusively shared between the Timer0 module and the watchdog timer. A prescaler assignment for the Timer0
REGISTER 6-1:
OPTION_REG REGISTER
R/W-1 RBPU bit 7 R/W-1 INTEDG R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit 0
bit 7 bit 6 bit 5
RBPU INTEDG T0CS: TMR0 Clock Source Select bit 1 = Transition on T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on T0CKI pin 0 = Increment on low-to-high transition on T0CKI pin PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module PS2:PS0: Prescaler Rate Select bits
Bit Value
000 001 010 011 100 101 110 111
bit 4
bit 3
bit 2-0
TMR0 Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256
WDT Rate 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128
Legend: R = Readable bit -n = Value at POR Note: W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
To avoid an unintended device RESET, the instruction sequence shown in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023, Section 11.6) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled.
DS30605C-page 40
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 6-1:
Address 01h 0Bh,8Bh 81h
REGISTERS ASSOCIATED WITH TIMER0
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR
xxxx xxxx
Value on all other RESETS
uuuu uuuu 0000 000u 1111 1111
TMR0 INTCON
Timer0 Module's register GIE PEIE T0IE T0CS INTE T0SE RBIE PSA T0IF PS2 INTF PS1 RBIF PS0
0000 000x 1111 1111
OPTION_REG RBPU INTEDG
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0.
2000 Microchip Technology Inc.
DS30605C-page 41
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 42
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
7.0 TIMER1 MODULE
The Timer1 module is a 16-bit timer/counter consisting of two 8-bit registers (TMR1H and TMR1L), which are readable and writable. The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The TMR1 Interrupt, if enabled, is generated on overflow, which is latched in interrupt flag bit TMR1IF (PIR1<0>). This interrupt can be enabled/disabled by setting/clearing TMR1 interrupt enable bit TMR1IE (PIE1<0>). Timer1 can operate in one of two modes: * As a timer * As a counter The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). In Timer mode, Timer1 increments every instruction cycle. In Counter mode, it increments on every rising edge of the external clock input. Timer1 can be enabled/disabled by setting/clearing control bit TMR1ON (T1CON<0>). Timer1 also has an internal "RESET input". This RESET can be generated by either of the two CCP modules (Section 9.0) using the special event trigger. Register 7-1 shows the Timer1 control register. When the Timer1 oscillator is enabled (T1OSCEN is set), the RC1/T1OSI/CCP2 and RC0/T1OSO/T1CKI pins become inputs. That is, the TRISC<1:0> value is ignored, and these pins read as `0'. Additional information on timer modules is available in the PICmicroTM Mid-range MCU Family Reference Manual (DS33023).
REGISTER 7-1:
T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h)
U-0 -- bit 7 U-0 -- R/W-0 R/W-0 R/W-0 T1OSCEN R/W-0 R/W-0 R/W-0 bit 0 T1CKPS1 T1CKPS0 T1SYNC TMR1CS TMR1ON
bit 7-6 bit 5-4
Unimplemented: Read as '0' T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value T1OSCEN: Timer1 Oscillator Enable Control bit 1 = Oscillator is enabled 0 = Oscillator is shut-off (The oscillator inverter is turned off to eliminate power drain) T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS = 1: 1 = Do not synchronize external clock input 0 = Synchronize external clock input TMR1CS = 0: This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.
bit 3
bit 2
bit 1
TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RC0/T1OSO/T1CKI (on the rising edge) 0 = Internal clock (FOSC/4) TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 0
2000 Microchip Technology Inc.
DS30605C-page 43
PIC16C63A/65B/73B/74B
7.1 Timer1 Operation in Timer Mode 7.2
Timer mode is selected by clearing the TMR1CS (T1CON<1>) bit. In this mode, the input clock to the timer is FOSC/4. The synchronize control bit T1SYNC (T1CON<2>) has no effect since the internal clock is always in sync.
Timer1 Operation in Synchronized Counter Mode
Counter mode is selected by setting bit TMR1CS. In this mode, the timer increments on every rising edge of clock input on pin RC1/T1OSI/CCP2, when bit T1OSCEN is set, or on pin RC0/T1OSO/T1CKI, when bit T1OSCEN is cleared. If T1SYNC is cleared, then the external clock input is synchronized with internal phase clocks. The synchronization is done after the prescaler stage. The prescaler stage is an asynchronous ripple counter. In this configuration during SLEEP mode, Timer1 will not increment even if the external clock is present, since the synchronization circuit is shut-off. The prescaler, however, will continue to increment.
FIGURE 7-1:
TIMER1 BLOCK DIAGRAM
Set Flag bit TMR1IF on Overflow TMR1H
TMR1 TMR1L
0 1 TMR1ON On/Off T1SYNC
Synchronized Clock Input
T1OSC RC0/T1OSO/T1CKI
(2)
1 T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock Prescaler 1, 2, 4, 8 0 2 T1CKPS1:T1CKPS0 TMR1CS
Synchronize det SLEEP Input
RC1/T1OSI/CCP2(2)
Note 1: When the T1OSCEN bit is cleared, the inverter is turned off. This eliminates power drain. 2: For the PIC16C65B/73B/74B, the Schmitt Trigger is not implemented in External Clock mode.
DS30605C-page 44
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
7.3 Timer1 Operation in Asynchronous Counter Mode
TABLE 7-1:
Osc Type LP
CAPACITOR SELECTION FOR THE TIMER1 OSCILLATOR
Freq C1 C2
If control bit T1SYNC (T1CON<2>) is set, the external clock input is not synchronized. The timer continues to increment asynchronous to the internal phase clocks. The timer will continue to run during SLEEP and can generate an interrupt-on-overflow, which will wake-up the processor. However, special precautions in software are needed to read/write the timer (Section 7.3.1). In Asynchronous Counter mode, Timer1 can not be used as a time-base for capture or compare operations.
7.3.1
READING AND WRITING TIMER1 IN ASYNCHRONOUS COUNTER MODE
Reading TMR1H or TMR1L while the timer is running from an external asynchronous clock will guarantee a valid read (taken care of in hardware). However, the user should keep in mind that reading the 16-bit timer in two 8-bit values itself poses certain problems, since the timer may overflow between the reads. For writes, it is recommended that the user simply stop the timer and write the desired values. A write contention may occur by writing to the timer registers, while the register is incrementing. This may produce an unpredictable value in the timer register. Reading the 16-bit value requires some care. Examples 12-2 and 12-3 in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) show how to read and write Timer1 when it is running in Asynchronous mode.
32 kHz 33 pF 33 pF 100 kHz 15 pF 15 pF 200 kHz 15 pF 15 pF These values are for design guidance only. Crystals Tested: 32.768 kHz Epson C-001R32.768K-A 20 PPM 100 kHz Epson C-2 100.00 KC-P 20 PPM 200 kHz STD XTL 200.000 kHz 20 PPM Note 1: Higher capacitance increases the stability of oscillator, but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components.
7.5
Resetting Timer1 using a CCP Trigger Output
If the CCP1 or CCP2 module is configured in Compare mode to generate a "special event trigger" (CCP1M3:CCP1M0 = 1011), this signal will reset Timer1. Note: The special event triggers from the CCP1 and CCP2 modules will not set interrupt flag bit TMR1IF (PIR1<0>).
7.4
Timer1 Oscillator
Timer1 must be configured for either timer or Synchronized Counter mode to take advantage of this feature. If Timer1 is running in Asynchronous Counter mode, this RESET operation may not work. In the event that a write to Timer1 coincides with a special event trigger from CCP1 or CCP2, the write will take precedence. In this mode of operation, the CCPRxH:CCPRxL register pair effectively becomes the period register for Timer1.
A crystal oscillator circuit is built-in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting control bit T1OSCEN (T1CON<3>). The oscillator is a low power oscillator rated up to 200 kHz. It will continue to run during SLEEP. It is primarily intended for use with a 32 kHz crystal. Table 7-1 shows the capacitor selection for the Timer1 oscillator. The Timer1 oscillator is identical to the LP oscillator. The user must provide a software time delay to ensure proper oscillator start-up.
7.6
Resetting of Timer1 Register Pair (TMR1H, TMR1L)
TMR1H and TMR1L registers are not reset to 00h on a POR, or any other RESET, except by the CCP1 and CCP2 special event triggers. T1CON register is reset to 00h on a Power-on Reset or a Brown-out Reset, which shuts off the timer and leaves a 1:1 prescale. In all other resets, the register is unaffected.
7.7
Timer1 Prescaler
The prescaler counter is cleared on writes to the TMR1H or TMR1L registers.
2000 Microchip Technology Inc.
DS30605C-page 45
PIC16C63A/65B/73B/74B
TABLE 7-2:
Address 0Bh,8Bh 0Ch 8Ch 0Eh 0Fh 10h Name INTCON PIR1 PIE1 TMR1L TMR1H T1CON
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Bit 7 GIE PSPIF(1) PSPIE(1) Bit 6 PEIE ADIF(2) ADIE(2) Bit 5 T0IE RCIF RCIE Bit 4 INTE TXIF TXIE Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF TMR2IF TMR2IE Bit 0 RBIF TMR1IF TMR1IE Value on: POR, BOR
0000 000x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx
Value on all other RESETS
0000 000u 0000 0000 0000 0000 uuuu uuuu uuuu uuuu --uu uuuu
Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON
--00 0000
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by the Timer1 module. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
DS30605C-page 46
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
8.0 TIMER2 MODULE
8.1 Timer2 Prescaler and Postscaler
Timer2 is an 8-bit timer with a prescaler and a postscaler. It can be used as the PWM time-base for the PWM mode of the CCP module(s). The TMR2 register is readable and writable, and is cleared on any device RESET. The input clock (FOSC/4) has a prescale option of 1:1, 1:4, or 1:16, selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). The Timer2 module has an 8-bit period register, PR2. Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. The PR2 register is initialized to FFh upon RESET. The match output of TMR2 goes through a 4-bit postscaler (which gives a 1:1 to 1:16 scaling inclusive) to generate a TMR2 interrupt (latched in flag bit TMR2IF, (PIR1<1>)). Timer2 can be shut-off by clearing control bit TMR2ON (T2CON<2>) to minimize power consumption. Register 8-1 shows the Timer2 control register. Additional information on timer modules is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). The prescaler and postscaler counters are cleared when any of the following occurs: * a write to the TMR2 register * a write to the T2CON register * any device RESET (POR, BOR, MCLR Reset, or WDT Reset) TMR2 is not cleared when T2CON is written.
8.2
Output of TMR2
The output of TMR2 (before the postscaler) is fed to the SSP module, which optionally uses it to generate the shift clock.
FIGURE 8-1:
Sets Flag TMR2 bit TMR2IF Output(1) RESET Postscaler 1:1 to 1:16 4 T2OUTPS3: T2OUTPS0 Note
TIMER2 BLOCK DIAGRAM
TMR2 reg Comparator
Prescaler 1:1, 1:4, 1:16 2 T2CKPS1: T2CKPS0
FOSC/4
EQ
PR2 reg
1: TMR2 register output can be software selected by the SSP module as a baud clock.
REGISTER 8-1:
T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h)
U-0 -- bit 7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 bit 0 TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0
bit 7 bit 6-3
Unimplemented: Read as '0' TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale 0010 = 1:3 Postscale * * * 1111 = 1:16 Postscale TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 2
bit 1-0
2000 Microchip Technology Inc.
DS30605C-page 47
PIC16C63A/65B/73B/74B
TABLE 8-1:
Address Name
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR
Value on all other RESETS
0Bh,8Bh 0Ch 8Ch 11h 12h 92h
INTCON PIR1 PIE1 TMR2 T2CON PR2
GIE PSPIF
(1)
PEIE ADIF
(2)
T0IE RCIF RCIE
INTE TXIF TXIE
RBIE SSPIF SSPIE
T0IF CCP1IF CCP1IE
INTF TMR2IF TMR2IE
RBIF TMR1IF TMR1IE
0000 000x 0000 000u 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000
PSPIE(1)
ADIE(2)
Timer2 Module's register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1
T2CKPS0 -000 0000 -000 0000
1111 1111 1111 1111
Timer2 Period register
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by the Timer2 module. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
DS30605C-page 48
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
9.0 CAPTURE/COMPARE/PWM MODULES
CCP2 Module: Capture/Compare/PWM Register2 (CCPR2) is comprised of two 8-bit registers: CCPR2L (low byte) and CCPR2H (high byte). The CCP2CON register controls the operation of CCP2. The special event trigger is generated by a compare match and will reset Timer1 and start an A/D conversion (if the A/D module is enabled). Additional information on CCP modules is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) and in "Using the CCP Modules" (AN594).
Each Capture/Compare/PWM (CCP) module contains a 16-bit register which can operate as a: * 16-bit Capture register * 16-bit Compare register * PWM Master/Slave Duty Cycle register Both the CCP1 and CCP2 modules are identical in operation, with the exception being the operation of the special event trigger. Table 9-1 and Table 9-2 show the resources and interactions of the CCP module(s). In the following sections, the operation of a CCP module is described with respect to CCP1. CCP2 operates the same as CCP1, except where noted. CCP1 Module: Capture/Compare/PWM Register1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). The CCP1CON register controls the operation of CCP1. The special event trigger is generated by a compare match and will reset Timer1.
TABLE 9-1:
CCP MODE - TIMER RESOURCES REQUIRED
Timer Resource Timer1 Timer1 Timer2
CCP Mode Capture Compare PWM
TABLE 9-2:
Capture Capture Compare PWM PWM PWM
INTERACTION OF TWO CCP MODULES
Interaction Same TMR1 time-base. The compare should be configured for the special event trigger, which clears TMR1. The compare(s) should be configured for the special event trigger, which clears TMR1. The PWMs will have the same frequency and update rate (TMR2 interrupt). None. None. Capture Compare Compare PWM Capture Compare
CCPx Mode CCPy Mode
2000 Microchip Technology Inc.
DS30605C-page 49
PIC16C63A/65B/73B/74B
REGISTER 9-1: CCP1CON REGISTER/CCP2CON REGISTER
U-0 -- bit 7 bit 7-6 bit 5-4 Unimplemented: Read as '0' CCPxX:CCPxY: PWM Least Significant bits Capture mode: Unused Compare mode: Unused PWM mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL. bit 3-0 CCPxM3:CCPxM0: CCPx Mode Select bits 0000 = Capture/Compare/PWM disabled (resets CCPx module) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (CCPxIF bit is set) 1001 = Compare mode, clear output on match (CCPxIF bit is set) 1010 = Compare mode, generate software interrupt on match (CCPxIF bit is set, CCPx pin is unaffected) 1011 = Compare mode, trigger special event (CCPxIF bit is set, CCPx pin is unaffected); CCP1 resets TMR1; CCP2 resets TMR1 and starts an A/D conversion (if A/D module is enabled) 11xx = PWM mode Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown U-0 -- R/W-0 CCPxX R/W-0 CCPxY R/W-0 CCPxM3 R/W-0 R/W-0 R/W-0 bit 0 CCPxM2 CCPxM1 CCPxM0
DS30605C-page 50
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
9.1 Capture Mode
9.1.2 TIMER1 MODE SELECTION
In Capture mode, CCPR1H:CCPR1L captures the 16-bit value of the TMR1 register when an event occurs on pin RC2/CCP1. An event is defined as one of the following and is configured using CCPxCON<3:0>: * * * * Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge Timer1 must be running in Timer mode or Synchronized Counter mode for the CCP module to use the capture feature. In Asynchronous Counter mode, the capture operation may not work.
9.1.3
SOFTWARE INTERRUPT
An event is selected by control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit CCP1IF (PIR1<2>) is set. The interrupt flag must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the previous captured value is overwritten by the new captured value.
When the Capture mode is changed, a false capture interrupt may be generated. The user should keep bit CCP1IE (PIE1<2>) clear to avoid false interrupts and should clear the flag bit CCP1IF following any such change in operating mode.
9.1.4
CCP PRESCALER
9.1.1
CCP PIN CONFIGURATION
There are four prescaler settings, specified by bits CCP1M3:CCP1M0. Whenever the CCP module is turned off, or the CCP module is not in Capture mode, the prescaler counter is cleared. Any RESET will clear the prescaler counter. Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore, the first capture may be from a non-zero prescaler. Example 9-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the "false" interrupt.
In Capture mode, the RC2/CCP1 pin should be configured as an input by setting the TRISC<2> bit. Note: If the RC2/CCP1 pin is configured as an output, a write to the port can cause a capture condition.
FIGURE 9-1:
CAPTURE MODE OPERATION BLOCK DIAGRAM
Set Flag bit CCP1IF (PIR1<2>)
EXAMPLE 9-1:
CLRF MOVLW
CHANGING BETWEEN CAPTURE PRESCALERS
Prescaler / 1, 4, 16 RC2/CCP1 pin
CCPR1H and Edge Detect Capture Enable TMR1H CCP1CON<3:0> Q's
CCPR1L
MOVWF
CCP1CON ; Turn CCP module off NEW_CAPT_PS ; Load the W reg with ; the new prescaler ; move value and CCP ON CCP1CON ; Load CCP1CON with this ; value
TMR1L
2000 Microchip Technology Inc.
DS30605C-page 51
PIC16C63A/65B/73B/74B
9.2 Compare Mode
9.2.4 SPECIAL EVENT TRIGGER
In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the RC2/CCP1 pin is: * Driven high * Driven low * Remains unchanged The action on the pin is based on the value of control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the same time, interrupt flag bit CCP1IF is set. In this mode, an internal hardware trigger is generated, which may be used to initiate an action. The special event trigger output of CCP1 resets the TMR1 register pair. This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1. The special event trigger output of CCP2 resets the TMR1 register pair and starts an A/D conversion (if the A/D module is enabled). Note: The special event trigger from the CCP1and CCP2 modules will not set interrupt flag bit TMR1IF (PIR1<0>).
FIGURE 9-2:
COMPARE MODE OPERATION BLOCK DIAGRAM
9.3
PWM Mode (PWM)
Special event trigger will: reset Timer1, but not set interrupt flag bit TMR1IF (PIR1<0>), and set bit GO/DONE (ADCON0<2>). Special Event Trigger Set Flag bit CCP1IF (PIR1<2>) CCPR1H CCPR1L Q S Output Logic RC2/CCP1 Match R pin TRISC<2> Output Enable CCP1CON<3:0> Mode Select Comparator TMR1H TMR1L
In Pulse Width Modulation mode, the CCPx pin produces up to a 10-bit resolution PWM output. Since the CCP1 pin is multiplexed with the PORTC data latch, the TRISC<2> bit must be cleared to make the CCP1 pin an output. Note: Clearing the CCP1CON register will force the CCP1 PWM output latch to the default low level. This is not the PORTC I/O data latch.
Figure 9-3 shows a simplified block diagram of the CCP module in PWM mode. For a step-by-step procedure on how to set up the CCP module for PWM operation, see Section 9.3.3.
9.2.1
CCP PIN CONFIGURATION
FIGURE 9-3:
The user must configure the RC2/CCP1 pin as an output by clearing the TRISC<2> bit. Note: Clearing the CCP1CON register will force the RC2/CCP1 compare output latch to the default low level. This is not the PORTC I/O data latch.
CCPR1L
SIMPLIFIED PWM BLOCK DIAGRAM
CCP1CON<5:4>
Duty Cycle Registers
9.2.2
TIMER1 MODE SELECTION
CCPR1H (Slave)
Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work.
Comparator
R
Q RC2/CCP1
TMR2
(Note 1) S TRISC<2> Clear Timer, CCP1 pin and latch D.C.
9.2.3
SOFTWARE INTERRUPT MODE
Comparator
When Generate Software Interrupt mode is chosen, the CCP1 pin is not affected. The CCPIF bit is set, causing a CCP interrupt (if enabled).
PR2
Note 1: 8-bit timer is concatenated with 2-bit internal Q clock, or 2 bits of the prescale, to create 10-bit time-base.
DS30605C-page 52
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
A PWM output (Figure 9-4) has a time-base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period).
9.3.2
PWM DUTY CYCLE
FIGURE 9-4:
Period
PWM OUTPUT
The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available: the CCPR1L contains the eight MSbs and the CCP1CON<5:4> contains the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The following equation is used to calculate the PWM duty cycle in time: PWM duty cycle = (CCPR1L:CCP1CON<5:4>) * TOSC * (TMR2 prescale value)
Duty Cycle TMR2 = PR2 (Timer2 RESET) TMR2 = Duty Cycle TMR2 = PR2 (Timer2 RESET)
CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not latched into CCPR1H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. The CCPR1H register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2, concatenated with an internal 2-bit Q clock, or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. Maximum PWM resolution (bits) for a given PWM frequency: FOSC log( FPWM log(2)
9.3.1
PWM PERIOD
The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: PWM period = [(PR2) + 1] * 4 * TOSC * (TMR2 prescale value) PWM frequency is defined as 1 / [PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) * The PWM duty cycle is latched from CCPR1L into CCPR1H Note: The Timer2 postscaler (see Section 8.1) is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output.
Resolution
=
)
bits
Note:
If the PWM duty cycle value is longer than the PWM period, the CCP1 pin will not be cleared.
9.3.3
SET-UP FOR PWM OPERATION
The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. 4. 5. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the TRISC<2> bit. Set the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP1 module for PWM operation.
TABLE 9-3:
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz
PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz 16 0xFF 10 4 0xFF 10 1 0xFF 10 1 0x3F 8 1 0x1F 7 1 0x17 5.5
Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits)
2000 Microchip Technology Inc.
DS30605C-page 53
PIC16C63A/65B/73B/74B
TABLE 9-4:
Address
0Bh,8Bh 0Ch 0Dh 8Ch 8Dh 87h 0Eh 0Fh 10h 15h 16h 17h 1Bh 1Ch 1Dh
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1
Bit 7
GIE PSPIF -- PSPIE --
(1) (1)
Name
INTCON PIR1 PIR2 PIE1 PIE2 TRISC TMR1L TMR1H T1CON CCPR1L CCPR1H CCP1CON CCPR2L CCPR2H CCP2CON
Bit 6
PEIE ADIF -- ADIE --
(2) (2)
Bit 5
T0IE RCIF -- RCIE --
Bit 4
INTE TXIF -- TXIE --
Bit 3
RBIE SSPIF -- SSPIE --
Bit 2
T0IF CCP1IF -- CCP1IE --
Bit 1
INTF TMR2IF -- TMR2IE --
Bit 0
RBIF TMR1IF CCP2IF TMR1IE CCP2IE
Value on: POR, BOR
0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 1111 1111 xxxx xxxx xxxx xxxx
Value on all other RESETS
0000 000u 0000 0000 ---- ---0 0000 0000 ---- ---0 1111 1111 uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu --00 0000 uuuu uuuu uuuu uuuu --00 0000
PORTC Data Direction register Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON
--00 0000 xxxx xxxx xxxx xxxx
Capture/Compare/PWM register1 (LSB) Capture/Compare/PWM register1 (MSB) -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0
--00 0000 xxxx xxxx xxxx xxxx
Capture/Compare/PWM register2 (LSB) Capture/Compare/PWM register2 (MSB) -- -- CCP2X CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0
--00 0000
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by Capture and Timer1. Note 1: The PSP is not implemented on the PIC16C63A/73B; always maintain these bits clear. 2: The A/D is not implemented on the PIC16C63A/65B; always maintain these bits clear.
TABLE 9-5:
Address 0Bh,8Bh 0Ch 0Dh 8Ch 8Dh 87h 11h 92h 12h 15h 16h 17h 1Bh 1Ch 1Dh Legend: Note 1: 2: Name INTCON PIR1 PIR2 PIE1 PIE2 TRISC TMR2 PR2 T2CON CCPR1L CCPR1H
REGISTERS ASSOCIATED WITH PWM AND TIMER2
Bit 7 GIE PSPIF(1) -- PSPIE(1) -- Bit 6 PEIE ADIF(2) -- ADIE(2) -- Bit 5 T0IE RCIF -- RCIE -- Bit 4 INTE TXIF -- TXIE -- Bit 3 RBIE SSPIF -- SSPIE -- Bit 2 T0IF CCP1IF -- CCP1IE -- Bit 1 INTF TMR2IF -- TMR2IE -- Bit 0 RBIF TMR1IF CCP2IF TMR1IE CCP2IE Value on: POR, BOR
0000 000x 0000 0000 ---- ---0 0000 0000 ---- ---0 1111 1111 0000 0000 1111 1111
Value on all other RESETS
0000 000u 0000 0000 ---- ---0 0000 0000 ---- ---0 1111 1111 0000 0000 1111 1111 -000 0000 uuuu uuuu uuuu uuuu --00 0000 uuuu uuuu uuuu uuuu --00 0000
PORTC Data Direction register Timer2 Module's register Timer2 Module's Period register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0
-000 0000 xxxx xxxx xxxx xxxx
Capture/Compare/PWM register1 (LSB) Capture/Compare/PWM register1 (MSB) -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0
CCP1CON CCPR2L CCPR2H CCP2CON
--00 0000 xxxx xxxx xxxx xxxx
Capture/Compare/PWM register2 (LSB) Capture/Compare/PWM register2 (MSB) -- -- CCP2X CCP2Y CCP2M3 CCP2M2 CCP2M1 CCP2M0
--00 0000
x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by PWM and Timer2. Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
DS30605C-page 54
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
10.0
10.1
SYNCHRONOUS SERIAL PORT (SSP) MODULE
SSP Module Overview
FIGURE 10-1:
SSP BLOCK DIAGRAM (SPI MODE)
Internal Data Bus Read SSPBUF reg Write
The Synchronous Serial Port (SSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be Serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can operate in one of two modes: * Serial Peripheral Interface (SPI) * Inter-Integrated Circuit (I2C) An overview of I2C operations and additional information on the SSP module can be found in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). Refer to Application Note AN578, "Use of the SSP Module in the I 2C Multi-Master Environment."
RC4/SDI/SDA RC5/SDO
SSPSR reg bit0 Shift Clock
SS Control Enable RA5/SS/AN4 Edge Select 2 Clock Select SSPM3:SSPM0 4 Edge Select RC3/SCK/ SCL TRISC<3> TMR2 Output 2 Prescaler TCY 4, 16, 64
10.2
SPI Mode
This section contains register definitions and operational characteristics of the SPI module. SPI mode allows 8 bits of data to be synchronously transmitted and received simultaneously. To accomplish communication, typically three pins are used: * Serial Data Out (SDO) RC5/SDO * Serial Data In (SDI) RC4/SDI/SDA * Serial Clock (SCK) RC3/SCK/SCL Additionally, a fourth pin may be used when in a Slave mode of operation: * Slave Select (SS) RA5/SS/AN4 When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON register (SSPCON<5:0>) and SSPSTAT<7:6>. These control bits allow the following to be specified: Master mode (SCK is the clock output) Slave mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Clock edge (output data on rising/falling edge of SCK) * Clock Rate (Master mode only) * Slave Select mode (Slave mode only) * * * *
To enable the serial port, SSP enable bit, SSPEN (SSPCON<5>) must be set. To reset or reconfigure SPI mode, clear bit SSPEN, re-initialize the SSPCON register, and then set bit SSPEN. This configures the SDI, SDO, SCK, and SS pins as serial port pins. For the pins to behave as the serial port function, they must have their data direction bits (in the TRISC register) appropriately programmed. That is: * * * * * * . SDI must have TRISC<4> set SDO must have TRISC<5> cleared SCK (Master mode) must have TRISC<3> cleared SCK (Slave mode) must have TRISC<3> set SS must have TRISA<5> set ADCON1 must configure RA5 as a digital I/O pin. Note 1: When the SPI is in Slave mode with SS pin control enabled (SSPCON<3:0> = 0100), the SPI module will reset if the SS pin is set to VDD. 2: If the SPI is used in Slave mode with CKE = '1', then the SS pin control must be enabled.
2000 Microchip Technology Inc.
DS30605C-page 55
PIC16C63A/65B/73B/74B
REGISTER 10-1: SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (ADDRESS 94h)
R/W-0 SMP bit 7 bit 7 SMP: SPI Data Input Sample Phase SPI Master mode: 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time (Microwire(R)) SPI Slave mode: SMP must be cleared when SPI is used in Slave mode I2 C mode: This bit must be maintained clear CKE: SPI Clock Edge Select (see Figure 10-2, Figure 10-3, and Figure 10-4) SPI mode: CKP = 0: 1 = Data transmitted on rising edge of SCK (Microwire alternate) 0 = Data transmitted on falling edge of SCK CKP = 1: 1 = Data transmitted on falling edge of SCK (Microwire default) 0 = Data transmitted on rising edge of SCK I2 C mode: This bit must be maintained clear D/A: Data/Address bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address P: STOP bit (I2C mode only). This bit is cleared when the SSP module is disabled, or when the START bit is detected last. SSPEN is cleared. 1 = Indicates that a STOP bit has been detected last (this bit is '0' on RESET) 0 = STOP bit was not detected last S: START bit (I2C mode only). This bit is cleared when the SSP module is disabled, or when the STOP bit is detected last. SSPEN is cleared. 1 = Indicates that a START bit has been detected last (this bit is '0' on RESET) 0 = START bit was not detected last R/W: Read/Write bit information (I2C mode only). This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next START bit, STOP bit, or ACK bit. 1 = Read 0 = Write UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated BF: Buffer Full Status bit Receive (SPI and I2 C modes): 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2 C mode only): 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown R/W-0 CKE R-0 D/A R-0 P R-0 S R-0 R/W R-0 UA R-0 BF bit 0
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
DS30605C-page 56
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
REGISTER 10-2: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)
R/W-0 WCOL bit 7 bit 7 WCOL: Write Collision Flag bit 1 = The SSPBUF register was written while still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Synchronous Serial Port Overflow Flag bit In SPI mode: 1 = A new byte was received while the SSPBUF register is still holding the previous unread data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in Slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2 C mode: 1 = A byte was received while the SSPBUF register is still holding the previous unread byte. SSPOV is a "don't care" in transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow SSPEN: Synchronous Serial Port Enable bit. When enabled, the SSP pins must be properly configured as input or output. In SPI mode: 1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins 0 = Disables serial port and configures these pins as I/O port pins In I2 C mode: 1 = Enables the serial port and configures the SDA and SCL pins as serial port pins 0 = Disables serial port and configures these pins as I/O port pins CKP: Clock Polarity Select bit In SPI mode: 1 = Idle state for clock is a high level (Microwire default) 0 = Idle state for clock is a low level (Microwire alternate) In I2 C mode: SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch). (Used to ensure data setup time.) SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0000 = SPI Master mode, clock = FOSC/4 0001 = SPI Master mode, clock = FOSC/16 0010 = SPI Master mode, clock = FOSC/64 0011 = SPI Master mode, clock = TMR2 output/2 0100 = SPI Slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI Slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin. 0110 = I2C Slave mode, 7-bit address 0111 = I2C Slave mode, 10-bit address 1011 = I2C firmware controlled Master mode (Slave idle) 1110 = I2C Slave mode, 7-bit address with START and STOP bit interrupts enabled 1111 = I2C Slave mode, 10-bit address with START and STOP bit interrupts enabled Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown R/W-0 SSPOV R/W-0 SSPEN R/W-0 CKP R/W-0 SSPM3 R/W-0 SSPM2 R/W-0 SSPM1 R/W-0 SSPM0 bit 0
bit 6
bit 5
bit 4
bit 3-0
2000 Microchip Technology Inc.
DS30605C-page 57
PIC16C63A/65B/73B/74B
FIGURE 10-2:
SCK (CKP = 0, CKE = 0) SCK (CKP = 0, CKE = 1) SCK (CKP = 1, CKE = 0) SCK (CKP = 1, CKE = 1) SDO SDI (SMP = 0) bit7 SDI (SMP = 1) bit7 SSPIF bit0 bit0 bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0
SPI MODE TIMING, MASTER MODE
FIGURE 10-3:
SS (optional)
SPI MODE TIMING (SLAVE MODE WITH CKE = 0)
SCK (CKP = 0) SCK (CKP = 1)
SDO SDI (SMP = 0)
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
bit7 SSPIF
bit0
DS30605C-page 58
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 10-4:
SS
SPI MODE TIMING (SLAVE MODE WITH CKE = 1)
SCK (CKP = 0) SCK (CKP = 1)
SDO
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
SDI (SMP = 0) bit7 SSPIF bit0
TABLE 10-1:
Address 0Bh,8Bh 0Ch 8Ch 87h 13h 14h 85h 94h
REGISTERS ASSOCIATED WITH SPI OPERATION
Bit 7 GIE PSPIF
(1)
Name INTCON PIR1 PIE1 TRISC SSPBUF
Bit 6 PEIE ADIF
(2)
Bit 5 T0IE RCIF RCIE
Bit 4 INTE TXIF TXIE
Bit 3 RBIE SSPIF SSPIE
Bit 2 T0IF
Bit 1 INTF
Bit 0 RBIF
Value on: POR, BOR
Value on all other RESETS
0000 000x 0000 000u
CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000 CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000 1111 1111 1111 1111 xxxx xxxx uuuu uuuu SSPM1 SSPM0 0000 0000 0000 0000 --11 1111 --11 1111 UA BF 0000 0000 0000 0000
PSPIE(1)
ADIE(2)
PORTC Data Direction register Synchronous Serial Port Receive Buffer/Transmit register SSPOV SSPEN -- CKE CKP SSPM3 SSPM2
SSPCON WCOL TRISA SSPSTAT -- SMP
PORTA Data Direction register D/A P S R/W
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used by the SSP in SPI mode. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
2000 Microchip Technology Inc.
DS30605C-page 59
PIC16C63A/65B/73B/74B
10.3 SSP I 2C Operation
The SSP module in I 2C mode fully implements all slave functions, except general call support, and provides interrupts on START and STOP bits in hardware to facilitate firmware implementation of the master functions. The SSP module implements the standard mode specifications as well as 7-bit and 10-bit addressing. Two pins are used for data transfer, the RC3/SCK/SCL pin, which is the clock (SCL), and the RC4/SDI/SDA pin, which is the data (SDA). The user must configure these pins as inputs or outputs through the TRISC<4:3> bits. External pull-up resistors for the SCL and SDA pins must be provided in the application circuit for proper operation of the I2C module. The SSP module functions are enabled by setting SSP enable bit SSPEN (SSPCON<5>). The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: * I 2C Slave mode (7-bit address) * I 2C Slave mode (10-bit address) * I 2C Slave mode (7-bit address), with START and STOP bit interrupts enabled to support firmware Master mode * I 2C Slave mode (10-bit address), with START and STOP bit interrupts enabled to support firmware Master mode * I 2C START and STOP bit interrupts enabled to support firmware Master mode, Slave is idle Selection of any I 2C mode with the SSPEN bit set, forces the SCL and SDA pins to be open drain, provided these pins are programmed to inputs by setting the appropriate TRISC bits. Additional information on SSP I 2C operation can be found in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023).
FIGURE 10-5:
SSP BLOCK DIAGRAM (I2C MODE)
Internal Data Bus Read SSPBUF reg Shift Clock SSPSR reg Write
10.3.1
SLAVE MODE
RC3/SCK/SCL
In Slave mode, the SCL and SDA pins must be configured as inputs (TRISC<4:3> set). The SSP module will override the input state with the output data when required (slave-transmitter). When an address is matched or the data transfer after an address match is received, the hardware automatically generates the acknowledge (ACK) pulse, and then loads the SSPBUF register with the received value currently in the SSPSR register.
RC4/SDI/ SDA
MSb
LSb
Match Detect
Addr Match
SSPADD reg START and STOP bit Detect Set, Reset S, P bits (SSPSTAT reg)
There are certain conditions that will cause the SSP module not to give this ACK pulse. They include (either or both): a) b) The buffer full bit BF (SSPSTAT<0>) was set before the transfer was received. The overflow bit SSPOV (SSPCON<6>) was set before the transfer was received.
The SSP module has five registers for I2C operation. These are the: * * * * * SSP Control Register (SSPCON) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - not directly accessible SSP Address Register (SSPADD)
In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF (PIR1<3>) is set. Table 10-2 shows what happens when a data transfer byte is received, given the status of bits BF and SSPOV. The shaded cells show the condition where user software did not properly clear the overflow condition. Flag bit BF is cleared by reading the SSPBUF register while bit SSPOV is cleared through software. The SCL clock input must have minimum high and low times for proper operation. The high and low times of the I2C specification, as well as the requirement of the SSP module, is shown in timing parameter #100 and parameter #101.
DS30605C-page 60
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
10.3.1.1 Addressing
1. 2. Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, 8-bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match, and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register. The buffer full bit, BF is set. An ACK pulse is generated. SSP interrupt flag bit, SSPIF (PIR1<3>) is set (interrupt is generated if enabled) - on the falling edge of the ninth SCL pulse. Receive first (high) byte of address (bits SSPIF, BF, and bit UA (SSPSTAT<1>) are set). Update the SSPADD register with second (low) byte of Address (clears bit UA and releases the SCL line). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive second (low) byte of address (bits SSPIF, BF, and UA are set). Update the SSPADD register with the first (high) byte of address, if match releases SCL line, this will clear bit UA. Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive Repeated START condition. Receive first (high) byte of address (bits SSPIF and BF are set). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF.
3. 4. 5.
6. 7. 8. 9.
In 10-bit address mode, two address bytes need to be received by the slave (Figure 10-7). The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. Bit R/W (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address, the first byte would equal `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for 10-bit address is as follows, with steps 7 - 9 for slave-transmitter:
TABLE 10-2:
DATA TRANSFER RECEIVED BYTE ACTIONS
SSPSR SSPBUF Generate ACK Pulse Set bit SSPIF (SSP Interrupt occurs if enabled)
Status Bits as Data Transfer is Received BF 0 1 1 0 Note: SSPOV
0 Yes Yes Yes 0 No No Yes, SSPOV is set 1 No No Yes 1 No No Yes Shaded cells show the conditions where the user software did not properly clear the overflow condition.
2000 Microchip Technology Inc.
DS30605C-page 61
PIC16C63A/65B/73B/74B
10.3.1.2 Reception
a) When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as any situation where a received byte in SSPBUF is overwritten by the next received byte before it has been read. An overflow has occurred when: The Buffer Full flag bit, BF(SSPSTAT<0>) was set, indicating that the byte in SSPBUF was waiting to be read when another byte was received. This sets the SSPOV flag. The overflow flag, SSPOV (SSPCON1<6>) was set.
b)
An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF (PIR1<3>) must be cleared in software. The SSPSTAT register is used to determine the status of the byte.
FIGURE 10-6:
I 2C WAVEFORMS FOR RECEPTION (7-BIT ADDRESS)
SDA
Receiving Address R/W=0 Receiving Data Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P
SCL
SSPIF (PIR1<3>)
Cleared in software
Bus Master terminates transfer
BF (SSPSTAT<0>)
SSPBUF register is read
SSPOV (SSPCON<6>) Bit SSPOV is set because the SSPBUF register is still full ACK is not sent
DS30605C-page 62
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
10.3.1.3 Transmission
When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit and pin RC3/SCK/SCL is held low. The transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then pin RC3/SCK/SCL should be enabled by setting bit CKP (SSPCON<4>). The master must monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 10-7). An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF must be cleared in software, and the SSPSTAT register is used to determine the status of the byte. Flag bit SSPIF is set on the falling edge of the ninth clock pulse. As a slave-transmitter, the ACK pulse from the master-receiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the ACK is latched by the slave, the slave logic is reset (resets SSPSTAT register) and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then pin RC3/SCK/SCL should be enabled by setting bit CKP.
FIGURE 10-7:
I 2C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
Receiving Address R/W = 1 A1 ACK D7 D6 D5 D4 Transmitting Data D3 D2 D1 D0 ACK
SDA
A7
A6
A5
A4
A3
A2
SCL
S
1 2 Data in sampled
3
4
5
6
7
8
9
1 SCL held low while CPU responds to SSPIF
2
3
4
5
6
7
8
9
P
SSPIF (PIR1<3>) BF (SSPSTAT<0>)
Cleared in software
SSPBUF is written in software CKP (SSPCON<4>)
From SSP Interrupt Service Routine
Set bit after writing to SSPBUF (the SSPBUF must be written to before the CKP bit can be set)
2000 Microchip Technology Inc.
DS30605C-page 63
PIC16C63A/65B/73B/74B
10.3.2 MASTER MODE 10.3.3 MULTI-MASTER MODE
Master mode of operation is supported in firmware using interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared from a RESET, or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle and both the S and P bits are clear. In Master mode, the SCL and SDA lines are manipulated by clearing the corresponding TRISC<4:3> bit(s). The output level is always low, irrespective of the value(s) in PORTC<4:3>. So when transmitting data, a '1' data bit must have the TRISC<4> bit set (input) and a '0' data bit must have the TRISC<4> bit cleared (output). The same scenario is true for the SCL line with the TRISC<3> bit. The following events will cause SSP Interrupt Flag bit, SSPIF, to be set (an SSP Interrupt will occur, if enabled): * START condition * STOP condition * Data transfer byte transmitted/received Master mode of operation can be done with either the Slave mode idle (SSPM3:SSPM0 = 1011), or with the slave active. When both Master and Slave modes are enabled, the software needs to differentiate the source(s) of the interrupt. In Multi-Master mode, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a RESET or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when bit P (SSPSTAT<4>) is set, or the bus is idle and both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. In Multi-Master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set TRISC<4:3>). There are two stages where this arbitration can be lost, these are: * Address Transfer * Data Transfer When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed, an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at a later time.
TABLE 10-3:
Address
REGISTERS ASSOCIATED WITH I2C OPERATION
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR 0000 000x 0000 0000 0000 0000 xxxx xxxx 0000 0000 0000 0000 0000 0000 1111 1111 Value on all other RESETS 0000 000u 0000 0000 0000 0000 uuuu uuuu 0000 0000 0000 0000 0000 0000 1111 1111
Name
0Bh, 8Bh 0Ch 8Ch 13h 93h 14h 94h 87h
INTCON PIR1 PIE1 SSPBUF SSPADD SSPCON SSPSTAT TRISC
GIE PSPIF(1) PSPIE
(1)
PEIE ADIF(2) ADIE
(2)
T0IE RCIF RCIE
INTE TXIF TXIE
RBIE
T0IF
INTF
RBIF
SSPIF CCP1IF TMR2IF TMR1IF SSPIE CCP1IE TMR2IE TMR1IE
Synchronous Serial Port Receive Buffer/Transmit register Synchronous Serial Port WCOL SMP(3) (I2C mode) Address register CKP P SSPM3 SSPM2 SSPM1 SSPM0 S R/W UA BF
SSPOV SSPEN CKE(3) D/A
PORTC Data Direction register
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by SSP module in I2C mode. Note 1: PSPIF and PSPIE are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: ADIF and ADIE are reserved on the PIC16C63A/65B; always maintain these bits clear. 3: Maintain these bits clear in I2C mode.
DS30605C-page 64
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
11.0 ADDRESSABLE UNIVERSAL SYNCHRONOUS ASYNCHRONOUS RECEIVER TRANSMITTER (USART)
as a half duplex synchronous system that can communicate with peripheral devices, such as A/D or D/A integrated circuits, Serial EEPROMs etc. The USART can be configured in the following modes: * Asynchronous (full duplex) * Synchronous - Master (half duplex) * Synchronous - Slave (half duplex) Bits SPEN (RCSTA<7>) and TRISC<7:6> have to be set in order to configure pins RC6/TX/CK and RC7/RX/DT as the universal synchronous asynchronous receiver transmitter.
The Universal Synchronous Asynchronous Receiver Transmitter (USART) module is one of the two serial I/O modules. (USART is also known as a Serial Communications Interface or SCI.) The USART can be configured as a full duplex asynchronous system that can communicate with peripheral devices, such as CRT terminals and personal computers, or it can be configured
REGISTER 11-1:
TXSTA: TRANSMIT STATUS AND CONTROL REGISTER (ADDRESS 98h)
R/W-0 CSRC bit 7 R/W-0 TX9 R/W-0 TXEN R/W-0 SYNC U-0 -- R/W-0 BRGH R-1 TRMT R/W-0 TX9D bit 0
bit 7
CSRC: Clock Source Select bit Asynchronous mode: Don't care Synchronous mode: 1 = Master mode (Clock generated internally from BRG) 0 = Slave mode (Clock from external source) TX9: 9-bit Transmit Enable bit 1 = Selects 9-bit transmission 0 = Selects 8-bit transmission TXEN: Transmit Enable bit 1 = Transmit enabled 0 = Transmit disabled Note: SREN/CREN overrides TXEN in SYNC mode. SYNC: USART Mode Select bit 1 = Synchronous mode 0 = Asynchronous mode Unimplemented: Read as '0' BRGH: High Baud Rate Select bit Asynchronous mode: 1 = High speed 0 = Low speed Synchronous mode: Unused in this mode TRMT: Transmit Shift Register Status bit 1 = TSR empty 0 = TSR full TX9D: 9th bit of Transmit Data. Can be parity bit. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 6
bit 5
bit 4
bit 3 bit 2
bit 1
bit 0
2000 Microchip Technology Inc.
DS30605C-page 65
PIC16C63A/65B/73B/74B
REGISTER 11-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER (ADDRESS 18h)
R/W-0 SPEN bit 7 bit 7 SPEN: Serial Port Enable bit 1 = Serial port enabled (configures RC7/RX/DT and RC6/TX/CK pins as serial port pins) 0 = Serial port disabled RX9: 9-bit Receive Enable bit 1 = Selects 9-bit reception 0 = Selects 8-bit reception SREN: Single Receive Enable bit Asynchronous mode: Don't care Synchronous mode - Master: 1 = Enables single receive 0 = Disables single receive This bit is cleared after reception is complete. Synchronous mode - Slave: Don't care CREN: Continuous Receive Enable bit Asynchronous mode: 1 = Enables continuous receive 0 = Disables continuous receive Synchronous mode: 1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN) 0 = Disables continuous receive Unimplemented: Read as '0' FERR: Framing Error bit 1 = Framing error (can be updated by reading RCREG register and receive next valid byte) 0 = No framing error OERR: Overrun Error bit 1 = Overrun error (can be cleared by clearing bit CREN) 0 = No overrun error RX9D: 9th bit of Received Data. (Can be parity bit. Calculated by firmware.) Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown R/W-0 RX9 R/W-0 SREN R/W-0 CREN U-0 -- R-0 FERR R-0 OERR R-x RX9D bit 0
bit 6
bit 5
bit 4
bit 3 bit 2
bit 1
bit 0
DS30605C-page 66
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
11.1 USART Baud Rate Generator (BRG)
It may be advantageous to use the high baud rate (BRGH = 1) even for slower baud clocks. This is because the FOSC/(16(X + 1)) equation can reduce the baud rate error in some cases. Writing a new value to the SPBRG register causes the BRG timer to be reset (or cleared). This ensures the BRG does not wait for a timer overflow before outputting the new baud rate.
The BRG supports both the Asynchronous and Synchronous modes of the USART. It is a dedicated 8-bit baud rate generator. The SPBRG register controls the period of a free running 8-bit timer. In Asynchronous mode, bit BRGH (TXSTA<2>) also controls the baud rate. In Synchronous mode, bit BRGH is ignored. Table 11-1 shows the formula for computation of the baud rate for different USART modes, which only apply in Master mode (internal clock). Given the desired baud rate and Fosc, the nearest integer value for the SPBRG register can be calculated using the formula in Table 11-1. From this, the error in baud rate can be determined.
11.1.1
SAMPLING
The data on the RC7/RX/DT pin is sampled three times near the center of each bit time by a majority detect circuit to determine if a high or a low level is present at the RX pin.
TABLE 11-1:
SYNC 0 1
BAUD RATE FORMULA
BRGH = 0 (Low Speed) (Asynchronous) Baud Rate = FOSC/(64(SPBRG+1)) (Synchronous) Baud Rate = FOSC/(4(SPBRG+1)) BRGH = 1 (High Speed) Baud Rate = FOSC/(16(SPBRG+1)) N/A
TABLE 11-2:
Address 98h 18h 99h
REGISTERS ASSOCIATED WITH BAUD RATE GENERATOR
Bit 7 CSRC SPEN Bit 6 TX9 RX9 Bit 5 TXEN SREN Bit 4 SYNC CREN Bit 3 -- -- Bit 2 BRGH FERR Bit 1 TRMT OERR Bit 0 TX9D RX9D Value on: POR, BOR
0000 -010 0000 -00x 0000 0000
Name TXSTA RCSTA SPBRG
Value on all other RESETS
0000 -010 0000 -00x 0000 0000
Baud Rate Generator register
Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used by the BRG.
2000 Microchip Technology Inc.
DS30605C-page 67
PIC16C63A/65B/73B/74B
11.2 USART Asynchronous Mode
In this mode, the USART uses standard nonreturn-to-zero (NRZ) format (one START bit, eight or nine data bits, and one STOP bit). The most common data format is 8 bits. An on-chip, dedicated, 8-bit baud rate generator can be used to derive standard baud rate frequencies from the oscillator. The USART transmits and receives the LSb first. The USART's transmitter and receiver are functionally independent, but use the same data format and baud rate. The baud rate generator produces a clock, either x16 or x64 of the bit shift rate, depending on bit BRGH (TXSTA<2>). Parity is not supported by the hardware, but can be implemented in software (and stored as the ninth data bit). Asynchronous mode is stopped during SLEEP. Asynchronous mode is selected by clearing bit SYNC (TXSTA<4>). The USART Asynchronous module consists of the following important elements: * * * * Baud Rate Generator Sampling Circuit Asynchronous Transmitter Asynchronous Receiver This interrupt can be enabled/disabled by setting/clearing the USART Transmit Enable bit TXIE (PIE1<4>). The flag bit TXIF will be set, regardless of the state of enable bit TXIE and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While flag bit TXIF indicates the status of the TXREG register, another bit TRMT (TXSTA<1>) shows the status of the TSR register. Status bit TRMT is a read only bit, which is set when the TSR register is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. Note 1: The TSR register is not mapped in data memory, so it is not available to the user. 2: Flag bit TXIF is set when enable bit TXEN is set. TXIF is cleared by loading TXREG. Transmission is enabled by setting enable bit TXEN (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data and the baud rate generator (BRG) has produced a shift clock (Figure 11-2). The transmission can also be started by first loading the TXREG register and then setting enable bit TXEN. Normally, when transmission is first started, the TSR register is empty. At that point, transfer to the TXREG register will result in an immediate transfer to TSR, resulting in an empty TXREG. A back-to-back transfer is thus possible (Figure 11-3). Clearing enable bit TXEN during a transmission will cause the transmission to be aborted and will reset the transmitter. As a result, the RC6/TX/CK pin will revert to hi-impedance. In order to select 9-bit transmission, transmit bit TX9 (TXSTA<6>) should be set and the ninth bit should be written to TX9D (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG register can result in an immediate transfer of the data to the TSR register (if the TSR is empty). In such a case, an incorrect ninth data bit may be loaded in the TSR register.
11.2.1
USART ASYNCHRONOUS TRANSMITTER
The USART transmitter block diagram is shown in Figure 11-1. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the STOP bit has been transmitted from the previous load. As soon as the STOP bit is transmitted, the TSR is loaded with new data from the TXREG register (if available). Once the TXREG register transfers the data to the TSR register (occurs in one TCY), the TXREG register is empty and the USART Transmit Flag bit TXIF (PIR1<4>) is set.
FIGURE 11-1:
USART TRANSMIT BLOCK DIAGRAM
Data Bus TXIF TXREG register 8 MSb (8) Interrupt TXEN Baud Rate CLK TRMT SPBRG Baud Rate Generator TX9 TX9D SPEN *** TSR register LSb 0 Pin Buffer and Control RC6/TX/CK pin
TXIE
DS30605C-page 68
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
Steps to follow when setting up an Asynchronous Transmission: 1. Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. (Section 11.1) Enable the asynchronous serial port by clearing bit SYNC and setting bit SPEN. If interrupts are desired, set interrupt enable bits TXIE (PIE1<4>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. 4. 5. 6. 7. If 9-bit transmission is desired, then set transmit bit TX9. Enable the transmission by setting bit TXEN, which will also set flag bit TXIF. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Load data to the TXREG register (starts transmission).
2. 3.
FIGURE 11-2:
Write to TXREG BRG output (shift clock) RC6/TX/CK (pin) TXIF bit (Transmit buffer reg. empty flag)
ASYNCHRONOUS MASTER TRANSMISSION
Word 1
START Bit
Bit 0
Bit 1 Word 1
Bit 7/8
STOP Bit
TRMT bit (Transmit shift reg. empty flag)
Word 1 Transmit Shift Reg
FIGURE 11-3:
Write to TXREG BRG output (shift clock) RC6/TX/CK (pin) TXIF bit (interrupt reg. flag)
ASYNCHRONOUS MASTER TRANSMISSION (BACK TO BACK)
Word 1 Word 2
START Bit
Bit 0
Bit 1 Word 1
Bit 7/8
STOP Bit
START Bit Word 2
Bit 0
TRMT bit (Transmit shift reg. empty flag)
Word 1 Transmit Shift Reg.
Word 2 Transmit Shift Reg.
Note: This timing diagram shows two consecutive transmissions.
TABLE 11-3:
Address 0Bh,8Bh 0Ch 18h 19h 8Ch 98h 99h
REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Bit 7 GIE PSPIF(1) SPEN Bit 6 PEIE ADIF(2) RX9 Bit 5 T0IE RCIF SREN RCIE TXEN Bit 4 INTE TXIF CREN TXIE SYNC Bit 3 RBIE SSPIF -- Bit 2 T0IF CCP1IF FERR Bit 1 INTF TMR2IF OERR TMR2IE TRMT Bit 0 RBIF RX9D Value on: POR, BOR 0000 000x
0000 -00x 0000 0000
Name INTCON PIR1 RCSTA TXREG PIE1 TXSTA
Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
TMR1IF 0000 0000
USART Transmit Register PSPIE(1) ADIE(2) CSRC TX9 SSPIE CCP1IE -- BRGH TX9D
TMR1IE 0000 0000
0000 -010 0000 0000
SPBRG Baud Rate Generator Register
Legend: u = unchanged, x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for asynchronous transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
2000 Microchip Technology Inc.
DS30605C-page 69
PIC16C63A/65B/73B/74B
11.2.2 USART ASYNCHRONOUS RECEIVER
ered register, i.e., it is a two-deep FIFO. It is possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting to the RSR register. On the detection of the STOP bit of the third byte, if the RCREG register is still full, then overrun error bit OERR (RCSTA<1>) will be set. The word in the RSR will be lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. Overrun bit OERR has to be cleared in software. This is done by resetting the receive logic (CREN is cleared and then set). If bit OERR is set, transfers from the RSR register to the RCREG register are inhibited, and no further data will be received; therefore, it is essential to clear error bit OERR if it is set. Framing error bit FERR (RCSTA<2>) is set if a STOP bit is detected as clear. Bit FERR and the 9th receive bit are buffered the same way as the receive data. Reading the RCREG will load bits RX9D and FERR with new values, therefore, it is essential for the user to read the RCSTA register before reading the RCREG register, in order not to lose the old FERR and RX9D information.
The receiver block diagram is shown in Figure 11-4. The data is received on the RC7/RX/DT pin and drives the data recovery block. The data recovery block is actually a high speed shifter operating at x16 times the baud rate, whereas the main receive serial shifter operates at the bit rate or at FOSC. Once Asynchronous mode is selected, reception is enabled by setting bit CREN (RCSTA<4>). The heart of the receiver is the receive (serial) shift register (RSR). After sampling the STOP bit, the received data in the RSR is transferred to the RCREG register (if it is empty). If the transfer is complete, USART Receive Flag bit RCIF (PIR1<5>) is set. This interrupt can be enabled/disabled by setting/clearing the USART Receive Enable bit RCIE (PIE1<5>). Flag bit RCIF is a read only bit, which is cleared by the hardware. It is cleared when the RCREG register has been read and is empty. The RCREG is a double buff-
FIGURE 11-4:
USART RECEIVE BLOCK DIAGRAM
x64 Baud Rate CLK CREN OERR FERR
FOSC
SPBRG / 64 or / 16 MSb STOP (8) 7 RSR Register *** 1 LSb 0 START
Baud Rate Generator RC7/RX/DT Pin Buffer and Control Data Recovery
RX9
SPEN
RX9D
RCREG Register FIFO
8 Interrupt RCIF RCIE Data Bus
DS30605C-page 70
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
Steps to follow when setting up an Asynchronous Reception: 1. Initialize the SPBRG register for the appropriate baud rate. If a high speed baud rate is desired, set bit BRGH. (Section 11.1). Enable the asynchronous serial port by clearing bit SYNC, and setting bit SPEN. If interrupts are desired, set interrupt enable bits RCIE (PIE1<5>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. If 9-bit reception is desired, then set bit RX9. 5. 6. Enable the reception by setting bit CREN. Flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing enable bit CREN.
7.
2. 3.
8. 9.
4.
FIGURE 11-5:
RX (pin) Rcv shift reg Rcv buffer reg Read Rcv buffer reg RCREG RCIF (interrupt flag) OERR bit CREN
ASYNCHRONOUS RECEPTION
START bit bit0 bit1 bit7/8 STOP bit START bit bit0 bit7/8 STOP bit START bit bit7/8 STOP bit
Word 1 RCREG
Word 2 RCREG
Note:
This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word, causing the OERR (overrun) bit to be set. An overrun error indicates an error in user's firmware.
TABLE 11-4:
Address 0Bh,8Bh 0Ch 18h 1Ah 8Ch 98h 99h
REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Bit 7 GIE PSPIF
(1)
Name INTCON PIR1 RCSTA
Bit 6 PEIE ADIF
(2)
Bit 5 T0IE RCIF SREN
Bit 4 INTE TXIF CREN
Bit 3 RBIE SSPIF --
Bit 2 T0IF CCP1IF FERR
Bit 1 INTF TMR2IF OERR
Bit 0 RBIF TMR1IF RX9D
Value on: POR, BOR 0000 000x
0000 0000 0000 -00x 0000 0000
Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
SPEN
RX9
RCREG USART Receive register PIE1 TXSTA SPBRG PSPIE(1) ADIE(2) CSRC TX9 RCIE TXEN TXIE SYNC SSPIE CCP1IE -- BRGH TMR2IE TRMT TMR1IE TX9D
0000 0000 0000 -010 0000 0000
Baud Rate Generator register
Legend: u = unchanged, x = unknown, - = unimplemented locations read as '0'. Shaded cells are not used for asynchronous reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C73/73A/76; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
2000 Microchip Technology Inc.
DS30605C-page 71
PIC16C63A/65B/73B/74B
11.2.3 USART SYNCHRONOUS MASTER MODE
Clearing enable bit TXEN, during a transmission, will cause the transmission to be aborted and will reset the transmitter. The DT and CK pins will revert to hi-impedance. If either bit CREN, or bit SREN is set during a transmission, the transmission is aborted and the DT pin reverts to a hi-impedance state (for a reception). The CK pin will remain an output if bit CSRC is set (internal clock). The transmitter logic, however, is not reset, although it is disconnected from the pins. In order to reset the transmitter, the user has to clear bit TXEN. If bit SREN is set (to interrupt an on-going transmission and receive a single word), then after the single word is received, bit SREN will be cleared and the serial port will revert back to transmitting, since bit TXEN is still set. The DT line will immediately switch from Hi-impedance Receive mode to transmit and start driving. To avoid this, bit TXEN should be cleared. In order to select 9-bit transmission, the TX9 (TXSTA<6>) bit should be set and the ninth bit should be written to bit TX9D (TXSTA<0>). The ninth bit must be written before writing the 8-bit data to the TXREG register. This is because a data write to the TXREG can result in an immediate transfer of the data to the TSR register (if the TSR is empty). If the TSR was empty and the TXREG was written before writing the "new" TX9D, the "present" value of bit TX9D is loaded. Steps to follow when setting up a Synchronous Master Transmission: 1. 2. 3. Initialize the SPBRG register for the appropriate baud rate (Section 11.1). Enable the synchronous master serial port by setting bits SYNC, SPEN and CSRC. If interrupts are desired, set interrupt enable bits TXIE (PIE1<4>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. If 9-bit transmission is desired, set bit TX9. Enable the transmission by setting bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREG register.
In Synchronous Master mode, the data is transmitted in a half-duplex manner, i.e., transmission and reception do not occur at the same time. When transmitting data, the reception is inhibited and vice versa. Synchronous mode is entered by setting bit SYNC (TXSTA<4>). In addition, enable bit SPEN (RCSTA<7>) is set in order to configure the RC6/TX/CK and RC7/RX/DT I/O pins to CK (clock) and DT (data) lines, respectively. The Master mode indicates that the processor transmits the master clock on the CK line. The Master mode is entered by setting bit CSRC (TXSTA<7>).
11.2.4
USART SYNCHRONOUS MASTER TRANSMISSION
The USART transmitter block diagram is shown in Figure 11-1. The heart of the transmitter is the transmit (serial) shift register (TSR). The shift register obtains its data from the read/write transmit buffer register, TXREG. The TXREG register is loaded with data in software. The TSR register is not loaded until the last bit has been transmitted from the previous load. As soon as the last bit is transmitted, the TSR is loaded with new data from the TXREG (if available). Once the TXREG register transfers the data to the TSR register (occurs in one TCYCLE), the TXREG is empty and interrupt flag bit TXIF (PIR1<4>) is set. The interrupt can be enabled/disabled by setting/clearing enable bit TXIE (PIE1<4>). Flag bit TXIF will be set, regardless of the state of enable bit TXIE and cannot be cleared in software. It will reset only when new data is loaded into the TXREG register. While flag bit TXIF indicates the status of the TXREG register, another bit TRMT (TXSTA<1>) shows the status of the TSR register. TRMT is a read only bit which is set when the TSR is empty. No interrupt logic is tied to this bit, so the user has to poll this bit in order to determine if the TSR register is empty. The TSR is not mapped in data memory, so it is not available to the user. Transmission is enabled by setting enable bit TXEN (TXSTA<5>). The actual transmission will not occur until the TXREG register has been loaded with data. The first data bit will be shifted out on the next available rising edge of the clock on the CK line. Data out is stable around the falling edge of the synchronous clock (Figure 11-6). The transmission can also be started by first loading the TXREG register and then setting bit TXEN (Figure 11-7). This is advantageous when slow baud rates are selected, since the BRG is kept in RESET when bits TXEN, CREN and SREN are clear. Setting enable bit TXEN will start the BRG, creating a shift clock immediately. Normally, when transmission is first started, the TSR register is empty, so a transfer to the TXREG register will result in an immediate transfer to TSR resulting in an empty TXREG. Back-to-back transfers are possible.
4. 5. 6. 7.
DS30605C-page 72
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 11-5:
Address 0Bh,8Bh 0Ch 18h 19h 8Ch 98h 99h
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER TRANSMISSION
Bit 7 GIE Bit 6 PEIE Bit 5 T0IE RCIF SREN Bit 4 INTE TXIF CREN Bit 3 RBIE SSPIF -- Bit 2 T0IF CCP1IF FERR Bit 1 INTF TMR2IF OERR Bit 0 RBIF TMR1IF RX9D Value on: POR, BOR 0000 000x
0000 0000 0000 -00x 0000 0000
Name INTCON PIR1 RCSTA TXREG PIE1 TXSTA SPBRG
Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
PSPIF(1) ADIF(2) SPEN
(1)
RX9
(2)
USART Transmit Register PSPIE ADIE RCIE TXEN TXIE SYNC SSPIE -- CCP1IE BRGH TMR2IE TMR1IE TRMT TX9D
0000 0000 0000 -010 0000 0000
CSRC
TX9
Baud Rate Generator Register
Legend: u = unchanged, x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous master transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
FIGURE 11-6:
SYNCHRONOUS TRANSMISSION
Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3Q4 Q1Q2 Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4
Q1Q2 Q3Q4 Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2Q3 Q4Q1 Q2 Q3Q4
RC7/RX/DT pin RC6/TX/CK pin Write to TXREG reg TXIF bit (Interrupt Flag)
TRMT TRMT bit
bit 0
bit 1
bit 2
bit 7
bit 0
bit 1
bit 7
Word 1
Word 2
Write word1
Write word2
TXEN bit
'1'
'1'
Note: Sync Master mode; SPBRG = '0'. Continuous transmission of two 8-bit words.
FIGURE 11-7:
SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
bit0 bit1 bit2 bit6 bit7
RC7/RX/DT pin RC6/TX/CK pin Write to TXREG reg
TXIF bit
TRMT bit
TXEN bit
2000 Microchip Technology Inc.
DS30605C-page 73
PIC16C63A/65B/73B/74B
11.2.5 USART SYNCHRONOUS MASTER RECEPTION
Steps to follow when setting up a Synchronous Master Reception: Initialize the SPBRG register for the appropriate baud rate. (Section 11.1) 2. Enable the synchronous master serial port by setting bits SYNC, SPEN, and CSRC. 3. Ensure bits CREN and SREN are clear. 4. If interrupts are desired, set interrupt enable bits RCIE (PIE1<5>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. 5. If 9-bit reception is desired, then set bit RX9. 6. If a single reception is required, set bit SREN. For continuous reception set bit CREN. 7. Interrupt flag bit RCIF will be set when reception is complete and an interrupt will be generated if enable bit RCIE was set. 8. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. 9. Read the 8-bit received data by reading the RCREG register. 10. If any error occurred, clear the error by clearing bit CREN. 1.
Once Synchronous mode is selected, reception is enabled by setting either enable bit SREN (RCSTA<5>), or enable bit CREN (RCSTA<4>). Data is sampled on the RC7/RX/DT pin on the falling edge of the clock. If enable bit SREN is set, then only a single word is received. If enable bit CREN is set, the reception is continuous until CREN is cleared. If both bits are set, CREN takes precedence. After clocking the last bit, the received data in the Receive Shift Register (RSR) is transferred to the RCREG register (if it is empty). When the transfer is complete, interrupt flag bit RCIF (PIR1<5>) is set. The interrupt from the USART can be enabled/disabled by setting/clearing enable bit RCIE (PIE1<5>). Flag bit RCIF is a read only bit, which is reset by the hardware. In this case, it is reset when the RCREG register has been read and is empty. The RCREG is a double buffered register, i.e., it is a two-deep FIFO. It is possible for two bytes of data to be received and transferred to the RCREG FIFO and a third byte to begin shifting into the RSR register. On the clocking of the last bit of the third byte, if the RCREG register is still full, then overrun error bit OERR (RCSTA<1>) is set. The word in the RSR will be lost. The RCREG register can be read twice to retrieve the two bytes in the FIFO. Bit OERR has to be cleared in software (by clearing bit CREN). If bit OERR is set, transfers from the RSR to the RCREG are inhibited, and no further data will be received; therefore, it is essential to clear bit OERR if it is set. The ninth receive bit is buffered the same way as the receive data. Reading the RCREG register will load bit RX9D with a new value, therefore it is essential for the user to read the RCSTA register before reading RCREG in order not to lose the old RX9D information.
DS30605C-page 74
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 11-6:
Address 0Bh,8Bh 0Ch 18h 1Ah 8Ch 98h 99h
REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION
Bit 7 GIE SPEN Bit 6 PEIE RX9 Bit 5 T0IE RCIF SREN RCIE TXEN Bit 4 INTE TXIF CREN TXIE SYNC Bit 3 RBIE SSPIF -- SSPIE -- Bit 2 T0IF CCP1IF FERR CCP1IE BRGH Bit 1 INTF TMR2IF OERR TMR2IE TRMT Bit 0 RBIF RX9D Value on: POR, BOR 0000 000x Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
Name INTCON PIR1 RCSTA RCREG PIE1 TXSTA SPBRG
PSPIF(1) ADIF(2)
TMR1IF 0000 0000
0000 -00x 0000 0000
USART Receive register PSPIE(1) ADIE(2) CSRC TX9 TX9D
TMR1IE 0000 0000
0000 -010 0000 0000
Baud Rate Generator register
Legend: u = unchanged, x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous master reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
FIGURE 11-8:
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
RC7/RX/DT pin RC6/TX/CK pin Write to bit SREN SREN bit CREN bit '0' RCIF bit (interrupt) Read RXREG
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
'0'
Note: Timing diagram demonstrates SYNC Master mode with bit SREN = '1' and bit BRG = '0'.
2000 Microchip Technology Inc.
DS30605C-page 75
PIC16C63A/65B/73B/74B
11.3 USART Synchronous Slave Mode
11.3.2
Synchronous Slave mode differs from the Master mode in the fact that the shift clock is supplied externally at the RC6/TX/CK pin (instead of being supplied internally in Master mode). This allows the device to transfer or receive data while in SLEEP mode. Slave mode is entered by clearing bit CSRC (TXSTA<7>).
USART SYNCHRONOUS SLAVE RECEPTION
The operation of the synchronous Master and Slave modes is identical, except in the case of the SLEEP mode. Also, bit SREN is a "don't care" in Slave mode. If receive is enabled by setting bit CREN prior to the SLEEP instruction, a word may be received during SLEEP. On completely receiving the word, the RSR register will transfer the data to the RCREG register. If interrupt enable bits RCIE and PEIE are set, the interrupt generated will wake the chip from SLEEP. If the global interrupt is enabled, the program will branch to the interrupt vector (0004h), otherwise execution will resume from the instruction following the SLEEP instruction. Steps to follow when setting up a Synchronous Slave Reception: 1. Enable the synchronous master serial port by setting bits SYNC and SPEN and clearing bit CSRC. If interrupts are desired, set interrupt enable bits RCIE (PIE1<5>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. If 9-bit reception is desired, set bit RX9. To enable reception, set enable bit CREN. Flag bit RCIF will be set when reception is complete and an interrupt will be generated, if enable bit RCIE was set. Read the RCSTA register to get the ninth bit (if enabled) and determine if any error occurred during reception. Read the 8-bit received data by reading the RCREG register. If any error occurred, clear the error by clearing bit CREN.
11.3.1
USART SYNCHRONOUS SLAVE TRANSMIT
The operation of the Synchronous Master and Slave modes are identical, except in the case of the SLEEP mode. If two words are written to the TXREG and then the SLEEP instruction is executed, the following will occur: a) b) c) d) The first word will immediately transfer to the TSR register and transmit. The second word will remain in TXREG register. Flag bit TXIF will not be set. When the first word has been shifted out of TSR, the TXREG register will transfer the second word to the TSR and flag bit TXIF will now be set. If interrupt enable bits TXIE and PEIE are set, the interrupt will wake the chip from SLEEP. If GIE is set, the program will branch to the interrupt vector (0004h), otherwise execution will resume from the instruction following the SLEEP instruction.
2.
e)
3. 4. 5.
6.
Steps to follow when setting up a Synchronous Slave Transmission: 1. Enable the synchronous slave serial port by setting bits SYNC and SPEN and clearing bit CSRC. Clear bits CREN and SREN. If interrupts are desired, set interrupt enable bits TXIE (PIE1<4>), PEIE (INTCON<6>), and GIE (INTCON<7>), as required. If 9-bit transmission is desired, set bit TX9. Enable the transmission by setting enable bit TXEN. If 9-bit transmission is selected, the ninth bit should be loaded in bit TX9D. Start transmission by loading data to the TXREG register. 7. 8.
2. 3.
4. 5. 6. 7.
DS30605C-page 76
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 11-7:
Address 0Bh,8Bh 0Ch 18h 19h 8Ch 98h 99h
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE TRANSMISSION
Bit 7 GIE Bit 6 PEIE Bit 5 T0IE RCIF Bit 4 INTE TXIF Bit 3 RBIE SSPIF -- Bit 2 T0IF CCP1IF FERR Bit 1 INTF TMR2IF OERR Bit 0 RBIF TMR1IF RX9D Value on: POR, BOR 0000 000x
0000 0000 0000 -00x 0000 0000
Name INTCON PIR1 RCSTA TXREG PIE1 TXSTA SPBRG
Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
PSPIF(1) ADIF(2) SPEN
(1)
RX9
(2)
SREN CREN
USART Transmit register PSPIE ADIE RCIE TXEN TXIE SYNC SSPIE CCP1IE -- BRGH TMR2IE TMR1IE TRMT TX9D
0000 0000 0000 -010 0000 0000
CSRC
TX9
Baud Rate Generator register
Legend: u = unchanged, x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous slave transmission. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
TABLE 11-8:
Address 0Bh,8Bh 0Ch 18h 1Ah 8Ch 98h 99h
REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
Bit 7 GIE PSPIF
(1)
Name INTCON PIR1 RCSTA RCREG PIE1 TXSTA SPBRG
Bit 6 PEIE ADIF
(2)
Bit 5 T0IE RCIF SREN
Bit 4 INTE TXIF CREN
Bit 3 RBIE SSPIF --
Bit 2 T0IF CCP1IF FERR
Bit 1 INTF TMR2IF OERR
Bit 0 RBIF TMR1IF RX9D
Value on: POR, BOR 0000 000x
0000 0000 0000 -00x 0000 0000
Value on all other RESETS 0000 000u
0000 0000 0000 -00x 0000 0000 0000 0000 0000 -010 0000 0000
SPEN
RX9
USART Receive register PSPIE(1) ADIE(2) CSRC TX9 RCIE TXEN TXIE SYNC SSPIE -- CCP1IE BRGH
TMR2IE TMR1IE 0000 0000 TRMT TX9D
0000 -010 0000 0000
Baud Rate Generator register
Legend: u = unchanged, x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous slave reception. Note 1: Bits PSPIE and PSPIF are reserved on the PIC16C63A/73B; always maintain these bits clear. 2: Bits ADIE and ADIF are reserved on the PIC16C63A/65B; always maintain these bits clear.
2000 Microchip Technology Inc.
DS30605C-page 77
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 78
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
12.0
Note:
ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE
The PIC16C63A and PIC16C65B do not include A/D modules. ADCON0, ADCON1 and ADRES registers are not implemented. ADIF and ADIE bits are reserved and should be maintained clear.
The A/D converter has a unique feature of being able to operate while the device is in SLEEP mode. To operate in SLEEP, the A/D conversion clock must be derived from the A/D's internal RC oscillator. The A/D module has three registers. These registers are: * A/D Result Register (ADRES) * A/D Control Register 0 (ADCON0) * A/D Control Register 1 (ADCON1) The ADCON0 register, shown in Register 12-1, controls the operation of the A/D module. The ADCON1 register, shown in Register 12-2, configures the functions of the port pins. The port pins can be configured as analog inputs (RA3 can also be a voltage reference), or as digital I/O. Additional information on using the A/D module can be found in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023) and in Application Note, AN546.
The 8-bit Analog-to-Digital (A/D) converter module has five inputs for the PIC16C73B and eight for the PIC16C74B. The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number. The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device's positive supply voltage (VDD), or the voltage level on the RA3/AN3/VREF pin.
REGISTER 12-1:
ADCON0 REGISTER (ADDRESS 1Fh)
R/W-0 ADCS1 bit 7 R/W-0 ADCS0 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 R/W-0 GO/DONE U-0 -- R/W-0 ADON bit 0
bit 7-6
ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from the internal A/D module RC oscillator) CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (RA0/AN0) 001 = channel 1, (RA1/AN1) 010 = channel 2, (RA2/AN2) 011 = channel 3, (RA3/AN3) 100 = channel 4, (RA5/AN4) 101 = channel 5, (RE0/AN5)(1) 110 = channel 6, (RE1/AN6)(1) 111 = channel 7, (RE2/AN7)(1) GO/DONE: A/D Conversion Status bit If ADON = 1: 1 = A/D conversion in progress (setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (this bit is automatically cleared by hardware when the A/D conversion is complete) Unimplemented: Read as '0' ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shut-off and consumes no operating current Note 1: A/D channels 5, 6 and 7 are implemented on the PIC16C74B only. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
bit 5-3
bit 2
bit 1 bit 0
2000 Microchip Technology Inc.
DS30605C-page 79
PIC16C63A/65B/73B/74B
REGISTER 12-2: ADCON1 REGISTER (ADDRESS 9Fh)
U-0 -- bit 7 bit 7-3 bit 2-0 Unimplemented: Read as '0' PCFG2:PCFG0: A/D Port Configuration Control bits RE0(1) RE1(1) RE2(1) A A D D D D D A A D D D D D A A D D D D D U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit 0
PCFG2:PCFG0 000 001 010 011 100 101 11x A = Analog input
RA0 A A A A A A D
RA1 A A A A A A D
RA2 A A A A D D D
RA5 A A A A D D D
RA3 A VREF A VREF A VREF D
VREF VDD RA3 VDD RA3 VDD RA3 VDD
D = Digital I/O
Note 1: RE0, RE1 and RE2 are implemented on the PIC16C74B only. Legend: R = Readable bit -n = Value at POR W = Writable bit '1' = Bit is set U = Unimplemented bit, read as `0' '0' = Bit is cleared x = Bit is unknown
DS30605C-page 80
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
The following steps should be followed for doing an A/D conversion: 1. Configure the A/D module: * Configure analog pins, voltage reference, and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear ADIF bit (PIR1<6>) * Set ADIE bit (PIE1<6>) * Set PEIE bit (INTCON<6>) * Set GIE bit (INTCON<7>) 3. 4. 5. Wait the required acquisition time. Set GO/DONE bit (ADCON0) to start conversion. Wait for A/D conversion to complete, by either: Polling for the GO/DONE bit to be cleared (if interrupts are disabled); OR Waiting for the A/D interrupt. 6. 7. Read A/D result register (ADRES), clear bit ADIF if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2 TAD is required before next acquisition starts.
2.
FIGURE 12-1:
A/D BLOCK DIAGRAM
CHS2:CHS0
111 110 101 100
RE2/AN7(1) RE1/AN6(1) RE0/AN5(1) RA5/AN4
VIN (Input Voltage)
011 010
RA3/AN3/VREF RA2/AN2
A/D Converter
001
RA1/AN1 VDD 000 or 010 or 100 or 11x
001 or 011 or 101 000
RA0/AN0
VREF (Reference Voltage)
PCFG2:PCFG0 Note 1: Not available on PIC16C73B.
2000 Microchip Technology Inc.
DS30605C-page 81
PIC16C63A/65B/73B/74B
12.1 A/D Acquisition Requirements
For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 12-2. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD), Figure 12-2. The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 10 k. After the analog input channel is selected (changed), the acquisition time (TACQ) must pass before the conversion can be started. To calculate the minimum acquisition time, Equation 12-1 may be used. This equation assumes that 1/2 LSb error is used (512 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified resolution. For more information, see the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). In general, however, given a maximum source impedance of 10 k and a worst case temperature of 100C, TACQ will be no more than 16 sec.
FIGURE 12-2:
ANALOG INPUT MODEL
VDD VT = 0.6 V RIC 1k Sampling Switch SS RSS CHOLD = DAC capacitance = 51.2 pF VSS Legend: CPIN VT = input capacitance = threshold voltage
Rs
ANx
VA
CPIN 5 pF
VT = 0.6 V
I leakage 500 nA
I leakage = leakage current at the pin due to various junctions RIC SS CHOLD = interconnect resistance = sampling switch = sample/hold capacitance (from DAC)
6V 5V VDD 4V 3V 2V
5 6 7 8 9 10 11 Sampling Switch (k)
EQUATION 12-1:
TACQ =
ACQUISITION TIME
Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient TAMP + TC + TCOFF TAMP = 5 S TC = - (51.2 pF)(1 k + RSS + RS) In(1/511) TCOFF = (Temp -25C)(0.05 S/C)
=
DS30605C-page 82
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
12.2 Selecting the A/D Conversion Clock 12.5 A/D Operation During SLEEP
The A/D module can operate during SLEEP mode. This requires that the A/D clock source be set to RC (ADCS1:ADCS0 = 11). When the RC clock source is selected, the A/D module waits one instruction cycle before starting the conversion. This allows the SLEEP instruction to be executed, which eliminates all digital switching noise from the conversion. When the conversion is completed, the GO/DONE bit will be cleared, and the result loaded into the ADRES register. If the A/D interrupt is enabled, the device will wake-up from SLEEP. If the A/D interrupt is not enabled, the A/D module will then be turned off, although the ADON bit will remain set. When the A/D clock source is another clock option (not RC), a SLEEP instruction will cause the present conversion to be aborted and the A/D module to be turned off, though the ADON bit will remain set. Turning off the A/D places the A/D module in its lowest current consumption state. Note: For the A/D module to operate in SLEEP, the A/D clock source must be set to RC (ADCS1:ADCS0 = 11). To perform an A/D conversion in SLEEP, ensure the SLEEP instruction immediately follows the instruction that sets the GO/DONE bit.
The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5 TAD per 8-bit conversion. The source of the A/D conversion clock is software selectable. The four possible options for TAD are: * * * * 2 TOSC 8 TOSC 32 TOSC Internal RC oscillator (2 - 6 S)
For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time (parameter #130).
12.3
Configuring Analog Port Pins
The ADCON1, TRISA and TRISE registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. Note 1: When reading the port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. 2: Analog levels on any pin that is defined as a digital input, but not as an analog input, may cause the input buffer to consume current that is out of the devices specification. 3: The TRISE register is not provided on the PIC16C73B.
12.6
Effects of a RESET
A device RESET forces all registers to their RESET state. The A/D module is disabled and any conversion in progress is aborted. All pins with analog functions are configured as analog inputs. The ADRES register will contain unknown data after a Power-on Reset.
12.7
Use of the CCP Trigger
12.4
Note:
A/D Conversions
The GO/DONE bit should NOT be set in the same instruction that turns on the A/D.
Clearing the GO/DONE bit during a conversion will abort the current conversion. The ADRES register will NOT be updated with the partially completed A/D conversion sample. That is, the ADRES register will continue to contain the value of the last completed conversion (or the last value written to the ADRES register). After the A/D conversion is aborted, a 2 TAD wait is required before the next acquisition is started. After this 2 TAD wait, an acquisition is automatically started on the selected channel. The GO/DONE bit can then be set to start another conversion.
An A/D conversion can be started by the "special event trigger" of the CCP2 module. This requires that the CCP2M3:CCP2M0 bits (CCP2CON<3:0>) be programmed as 1011 and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the GO/DONE bit will be set, starting the A/D conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead (moving the ADRES to the desired location). The appropriate analog input channel must be selected and the minimum acquisition done before the "special event trigger" sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), then the "special event trigger" will be ignored by the A/D module, but will still reset the Timer1 counter.
2000 Microchip Technology Inc.
DS30605C-page 83
PIC16C63A/65B/73B/74B
TABLE 12-1:
Address
0Bh,8Bh 0Ch 8Ch 0Dh 8Dh 1Eh 1Fh 9Fh 05h 85h 09h 89h
SUMMARY OF A/D REGISTERS (PIC16C73B/74B ONLY)
Bit 7
GIE PSPIF(1) PSPIE(1) -- --
Name
INTCON PIR1 PIE1 PIR2 PIE2 ADRES ADCON0 ADCON1 PORTA TRISA PORTE TRISE
Bit 6
PEIE ADIF ADIE -- --
Bit 5
T0IE RCIF RCIE -- --
Bit 4
INTE TXIF TXIE -- --
Bit 3
RBIE SSPIF SSPIE -- --
Bit 2
T0IF CCP1IF CCP1IE -- --
Bit 1
INTF TMR2IF TMR2IE -- --
Bit 0
RBIF TMR1IF TMR1IE CCP1IF CCP1IE
Value on: POR, BOR
0000 000x 0000 0000 0000 0000 ---- ---0 ---- ---0 xxxx xxxx
Value on all other RESETS
0000 000u 0000 0000 0000 0000 ---- ---0 ---- ---0 uuuu uuuu 0000 00-0 ---- -000 --0u 0000 --11 1111 ---- -uuu 0000 -111
A/D Result register ADCS1 -- -- -- -- IBF ADCS0 -- -- -- -- OBF CHS2 -- RA5 CHS1 -- RA4 CHS0 -- RA3 GO/DONE PCFG2 RA2 -- PCFG1 RA1 ADON PCFG0 RA0
0000 00-0 ---- -000 --0x 0000 --11 1111
PORTA Data Direction register -- IBOV -- PSPMODE -- -- RE2 RE1 RE0
---- -xxx 0000 -111
PORTE Data Direction bits
Legend: x = unknown, u = unchanged, - = unimplemented, read as '0'. Shaded cells are not used for A/D conversion. Note 1: Bits PSPIE and PSPIF are reserved on the PIC6C63A/73B; always maintain these bits clear.
DS30605C-page 84
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
13.0 SPECIAL FEATURES OF THE CPU
timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in RESET until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only and is designed to keep the part in RESET, while the power supply stabilizes. With these two timers on-chip, most applications need no external RESET circuitry. SLEEP mode is designed to offer a very low current power-down mode. The user can wake-up from SLEEP through external RESET, WDT wake-up or through an interrupt. Several oscillator options are also made available to allow the part to fit the application. The RC oscillator option saves system cost, while the LP crystal option saves power. A set of configuration bits are used to select various options.
What sets a microcontroller apart from other processors are special circuits to deal with the needs of realtime applications. The PIC16CXX family has a host of such features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These are: * Oscillator selection * RESET - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) * Interrupts * Watchdog Timer (WDT) * SLEEP * Code protection * ID locations * In-Circuit Serial Programming (ICSP) The PIC16CXX has a Watchdog Timer which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two
13.1
Configuration Bits
The configuration bits can be programmed (read as '0') or left unprogrammed (read as '1') to select various device configurations. These bits are mapped in program memory location 2007h. The user will note that address 2007h is beyond the user program memory space, and can be accessed only during programming.
REGISTER 13-1:
CP1 bit 13
CONFIGURATION WORD (CONFIG 2007h)
CP1 CP0 CP1 CP0 -- BODEN CP1 CP0 PWRTE WDTE FOSC1 FOSC0 bit 0
CP0
bits 13-8, CP1:CP0: Code Protection bits(2) 5-4 11 = Code protection off 10 = Upper half of program memory code protected 01 = Upper 3/4th of program memory code protected 00 = All memory is code protected bit 7 bit 6 Unimplemented: Read as '1' BODEN: Brown-out Reset Enable bit(1) 1 = BOR enabled 0 = BOR disabled PWRTE: Power-up Timer Enable bit(1) 1 = PWRT disabled 0 = PWRT enabled WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT), regardless of the value of PWRTE. 2: All of the CP1:CP0 pairs have to be given the same value to enable the code protection scheme listed.
bit 3
bit 2
bit 1-0
2000 Microchip Technology Inc.
DS30605C-page 85
PIC16C63A/65B/73B/74B
13.2
13.2.1
Oscillator Configurations
OSCILLATOR TYPES
FIGURE 13-1:
The PIC16CXX can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: * * * * LP XT HS RC Low Power Crystal Crystal/Resonator High Speed Crystal/Resonator Resistor/Capacitor
CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION)
OSC1 To internal logic SLEEP PIC16CXX
C1 XTAL OSC2 RS C2 (Note 1) RF
13.2.2
CRYSTAL OSCILLATOR/CERAMIC RESONATORS
See Table 13-1 and Table 13-2 for recommended values of C1 and C2. Note 1: A series resistor may be required for AT strip cut crystals.
In XT, LP, or HS modes, a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 13-1). The PIC16CXX oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can have an external clock source to drive the OSC1/ CLKIN pin (Figure 13-2). See the PICmicroTM MidRange MCU Reference Manual (DS33023) for details on building an external oscillator.
FIGURE 13-2:
EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION)
OSC1 PIC16CXX
Clock from ext. system Open
OSC2
DS30605C-page 86
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 13-1:
Ranges Tested: Mode Freq OSC1 OSC2
CERAMIC RESONATORS
Note 1: Higher capacitance increases the stability of the oscillator, but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 3: Rs may be required in HS mode, as well as XT mode, to avoid overdriving crystals with low drive level specification. 4: Oscillator performance should be verified at the expected voltage and temperature extremes in which the application is expected to operate.
XT
455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz
68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF
68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF
HS Note:
These values are for design guidance only. See notes following Table 13-1 and Table 13-2.
Resonators Used:
455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz Note:
Panasonic EFO-A455K04B Murata Erie CSA2.00MG Murata Erie CSA4.00MG Murata Erie CSA8.00MT Murata Erie CSA16.00MX
0.3% 0.5% 0.5% 0.5% 0.5%
13.2.3
RC OSCILLATOR
Resonators used did not have built-in capacitors.
TABLE 13-2:
Osc Type LP
CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR
Crystal Freq 32 kHz 200 kHz Cap. Range C1 33 pF 15 pF 47-68 pF 15 pF 15 pF 15 pF 15-33 pF 15-33 pF Cap. Range C2 33 pF 15 pF 47-68 pF 15 pF 15 pF 15 pF 15-33 pF 15-33 pF
XT
200 kHz 1 MHz 4 MHz
For timing insensitive applications, the "RC" device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. The oscillator frequency will vary from unit to unit due to normal process variation. The difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 13-3 shows how the R/C combination is connected to the PIC16CXX. The oscillator frequency, divided by 4, is available on the OSC2/CLKOUT pin, and can be used for test purposes or to synchronize other logic (see Figure 3-2 for waveform).
HS
4 MHz 8 MHz 20 MHz
FIGURE 13-3:
VDD REXT
RC OSCILLATOR MODE
Note:
These values are for design guidance only. See notes following Table 13-1 and Table 13-2.
Crystals Used: 32 kHz 200 kHz 1 MHz 4 MHz 8 MHz 20 MHz Epson C-001R32.768K-A STD XTL 200.000KHz ECS ECS-10-13-1 ECS ECS-40-20-1 EPSON CA-301 8.000M-C EPSON CA-301 20.000M-C 20 PPM 20 PPM 50 PPM 50 PPM 30 PPM 30 PPM
OSC1 CEXT VSS FOSC/4 OSC2/CLKOUT
Internal Clock PIC16CXX
Recommended Values: REXT = 3 kW to 100 kW CEXT = 20 pf to 30 pF
2000 Microchip Technology Inc.
DS30605C-page 87
PIC16C63A/65B/73B/74B
13.3 RESET
The PIC16CXX differentiates between various kinds of RESET: * * * * * Power-on Reset (POR) MCLR Reset during normal operation MCLR Reset during SLEEP WDT Reset (normal operation) Brown-out Reset (BOR) on MCLR Reset during SLEEP, and on BOR. The TO and PD bits are set or cleared differently in different RESET situations, as indicated in Table 13-4. These bits are used in software to determine the nature of the RESET. See Table 13-6 for a full description of RESET states of all registers. A simplified block diagram of the on-chip RESET circuit is shown in Figure 13-4. The PICmicro devices have a MCLR noise filter in the MCLR Reset path. The filter will detect and ignore small pulses. It should be noted that internal RESET sources do not drive MCLR pin low.
Some registers are not affected in any RESET condition; their status is unknown on POR and unchanged in any other RESET. Most other registers are reset to a "RESET state" on POR, on the MCLR and WDT Reset,
FIGURE 13-4:
SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External RESET
MCLR WDT Module VDD Rise Detect VDD Brown-out Reset OST/PWRT
SLEEP WDT Time-out Reset Power-on Reset S
BODEN
OST 10-bit Ripple Counter OSC1 (Note 1) PWRT On-chip 10-bit Ripple Counter RC OSC R Q
Chip Reset
Enable PWRT Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin.
DS30605C-page 88
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
13.4
13.4.1
RESETS
POWER-ON RESET (POR)
13.4.4
BROWN-OUT RESET (BOR)
A Power-on Reset pulse is generated on-chip when VDD rise is detected (parameters D003 and D004, in the range of 1.5V - 2.1V). To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create a POR. When the device starts normal operation (exits the RESET condition), device operating parameters (voltage, frequency, temperature) must be met to ensure operation. If these conditions are not met, the device must be held in RESET until the operating conditions are met. The device may be held in RESET by keeping MCLR at Vss. For additional information, refer to Application Note AN607, "Power-up Trouble Shooting."
The configuration bit, BODEN, can enable or disable the Brown-out Reset circuit. If VDD falls below VBOR (parameter D005, about 4V) for longer than TBOR (parameter #35, about 100S), the brown-out situation will reset the device. If VDD falls below VBOR for less than TBOR, a RESET may not occur. Once the brown-out occurs, the device will remain in Brown-out Reset until VDD rises above VBOR. The Power-up Timer then keeps the device in RESET for TPWRT (parameter #33, about 72mS). If VDD should fall below VBOR during TPWRT, the Brown-out Reset process will restart when VDD rises above VBOR with the Power-up Timer Reset. The Power-up Timer is always enabled when the Brown-out Reset circuit is enabled, regardless of the state of the PWRT configuration bit.
13.4.5
TIME-OUT SEQUENCE
13.4.2
POWER-UP TIMER (PWRT)
The Power-up Timer provides a fixed 72 ms nominal time-out on power-up from the POR. The PWRT operates on an internal RC oscillator. The device is kept in RESET as long as the PWRT is active. The PWRT's time delay allows VDD to rise to an acceptable level. A configuration bit is provided to enable/disable the PWRT. The power-up time delay will vary from chip to chip, due to VDD, temperature and process variation. See DC parameters for details (TPWRT, parameter #33).
On power-up, the time-out sequence is as follows: the PWRT delay starts (if enabled) when a POR occurs. Then, OST starts counting 1024 oscillator cycles when PWRT ends (LP, XT, HS). When the OST ends, the device comes out of RESET. If MCLR is kept low long enough, the time-outs will expire. Bringing MCLR high will begin execution immediately. This is useful for testing purposes or to synchronize more than one PIC16CXX device operating in parallel. Table 13-5 shows the RESET conditions for the STATUS, PCON and PC registers, while Table 13-6 shows the RESET conditions for all the registers.
13.4.3
OSCILLATOR START-UP TIMER (OST)
13.4.6
The Oscillator Start-up Timer provides a delay of 1024 oscillator cycles (from OSC1 input) after the PWRT delay, if enabled. This helps to ensure that the crystal oscillator or resonator has started and stabilized. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP.
POWER CONTROL/STATUS REGISTER (PCON)
The Brown-out Reset Status bit, BOR, is unknown on a POR. It must be set by the user and checked on subsequent RESETS to see if bit BOR was cleared, indicating a BOR occurred. The BOR bit is not predictable if the Brown-out Reset circuitry is disabled. The Power-on Reset Status bit, POR, is cleared on a POR and unaffected otherwise. The user must set this bit following a POR and check it on subsequent RESETS to see if it has been cleared.
2000 Microchip Technology Inc.
DS30605C-page 89
PIC16C63A/65B/73B/74B
TABLE 13-3: TIME-OUT IN VARIOUS SITUATIONS
Power-up PWRTE = 0 72 ms + 1024TOSC 72 ms PWRTE = 1 1024TOSC -- Brown-out 72 ms + 1024TOSC 72 ms Wake-up from SLEEP 1024TOSC -- Oscillator Configuration XT, HS, LP RC
TABLE 13-4:
POR 0 0 0 1 1 1 1 1 BOR x x x 0 1 1 1 1
STATUS BITS AND THEIR SIGNIFICANCE
TO 1 0 x 1 0 0 u 1 PD 1 x 0 1 1 0 u 0 Power-on Reset Illegal, TO is set on POR Illegal, PD is set on POR Brown-out Reset WDT Reset WDT Wake-up MCLR Reset during normal operation MCLR Reset during SLEEP or interrupt wake-up from SLEEP
Legend: x = don't care, u = unchanged
TABLE 13-5:
RESET CONDITION FOR SPECIAL REGISTERS
Condition Program Counter 000h 000h 000h 000h PC + 1 000h PC + 1(1) STATUS Register 0001 1xxx 000u uuuu 0001 0uuu 0000 1uuu uuu0 0uuu 000x xuuu uuu1 0uuu PCON Register ---- --0x ---- --uu ---- --uu ---- --uu ---- --uu ---- --u0 ---- --uu
Power-on Reset MCLR Reset during normal operation MCLR Reset during SLEEP WDT Reset WDT Wake-up Brown-out Reset Interrupt wake-up from SLEEP
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0' Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h).
REGISTER 13-2:
IRP RP1
STATUS REGISTER
RP0 TO PD Z DC C
REGISTER 13-3:
-- --
PCON REGISTER
-- -- -- -- POR BOR
DS30605C-page 90
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 13-6:
Register W INDF TMR0 PCL STATUS FSR PORTA PORTB PORTC PORTD PORTE PCLATH INTCON
INITIALIZATION CONDITIONS FOR ALL REGISTERS
Applicable Devices 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B Power-on Reset Brown-out Reset xxxx xxxx N/A xxxx xxxx 0000h 0001 1xxx xxxx xxxx --0x 0000 xxxx xxxx xxxx xxxx xxxx xxxx ---- -xxx ---0 0000 0000 000x -0-- 0000 -000 0000 0000 0000 0000 0000 ---- ---0 xxxx xxxx xxxx xxxx --00 0000 0000 0000 -000 0000 xxxx xxxx 0000 0000 xxxx xxxx xxxx xxxx --00 0000 0000 -00x 0000 0000 0000 0000 xxxx xxxx xxxx xxxx 0000 0000 xxxx xxxx MCLR Resets WDT Reset uuuu uuuu N/A uuuu uuuu 0000h 000q quuu(3) uuuu uuuu --0u 0000 uuuu uuuu uuuu uuuu uuuu uuuu ---- -uuu ---0 0000 0000 000u -0-- 0000 -000 0000 0000 0000 0000 0000 ---- ---0 uuuu uuuu uuuu uuuu --uu uuuu 0000 0000 -000 0000 uuuu uuuu 0000 0000 uuuu uuuu uuuu uuuu --00 0000 0000 -00x 0000 0000 0000 0000 uuuu uuuu uuuu uuuu 0000 0000 uuuu uuuu Wake-up via WDT or Interrupt uuuu uuuu N/A uuuu uuuu PC + 1(2) uuuq quuu(3) uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---- -uuu ---u uuuu uuuu uuuu(1) -u-- uuuu(1) -uuu uuuu(1) uuuu uuuu(1) uuuu uuuu(1) ---- ---u(1) uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu -uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu --uu uuuu uuuu -uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu
PIR1
63A 63A
PIR2 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON RCSTA TXREG RCREG CCPR2L CCPR2H CCP2CON ADRES
63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 13-5 for RESET value for specific condition.
2000 Microchip Technology Inc.
DS30605C-page 91
PIC16C63A/65B/73B/74B
TABLE 13-6:
Register ADCON0 OPTION_REG TRISA TRISB TRISC TRISD TRISE
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
Applicable Devices 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 63A 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 65B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 73B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B 74B Power-on Reset Brown-out Reset 0000 00-0 1111 1111 --11 1111 1111 1111 1111 1111 1111 1111 0000 -111 --00 0000 0-00 0000 -000 0000 0000 0000 ---- ---0 ---- --0q 1111 1111 0000 0000 --00 0000 0000 -010 0000 0000 ---- -000
(3)
MCLR Resets WDT Reset 0000 00-0 1111 1111 --11 1111 1111 1111 1111 1111 1111 1111 0000 -111 --00 0000 0-00 0000 -000 0000 0000 0000 ---- ---0 ---- --uu 1111 1111 0000 0000 --00 0000 0000 -010 0000 0000 ---- -000
Wake-up via WDT or Interrupt uuuu uu-u uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu -uuu --uu uuuu u-uu uuuu -uuu uuuu uuuu uuuu ---- ---u ---- --uu 1111 1111 uuuu uuuu --uu uuuu uuuu -uuu uuuu uuuu ---- -uuu
PIE1
PIE2 PCON PR2 SSPADD SSPSTAT TXSTA SPBRG ADCON1
Legend: u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition Note 1: One or more bits in INTCON, PIR1 and/or PIR2 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 13-5 for RESET value for specific condition.
DS30605C-page 92
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
13.5 Interrupts
Note: The Interrupt Control register (INTCON) records individual interrupt requests in flag bits. It also has individual and global interrupt enable bits. Note: Individual interrupt flag bits are set, regardless of the status of their corresponding mask bit, or the GIE bit. If an interrupt occurs while the Global Interrupt Enable (GIE) bit is being cleared, the GIE bit may unintentionally be re-enabled by the user's Interrupt Service Routine (the RETFIE instruction). The events that would cause this to occur are:
A global interrupt enable bit, GIE (INTCON<7>), enables (if set) all unmasked interrupts, or disables (if cleared) all interrupts. When bit GIE is enabled, and an interrupt's flag bit and mask bit are set, the interrupt will vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt bits are set, regardless of the status of the GIE bit. The GIE bit is cleared on RESET. The "return from interrupt" instruction, RETFIE, exits the interrupt routine, as well as sets the GIE bit, which re-enables interrupts. The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register. The peripheral interrupt flags are contained in the special function registers PIR1 and PIR2. The corresponding interrupt enable bits are contained in special function registers PIE1 and PIE2 and the peripheral interrupt enable bit is contained in special function register INTCON. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed onto the stack, and the PC is loaded with 0004h. Once in the Interrupt Service Routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit(s) must be cleared in software before re-enabling interrupts to avoid recursive interrupts. For external interrupt events, such as the INT pin or PORTB change interrupt, the interrupt latency will be three or four instruction cycles. The exact latency depends when the interrupt event occurs. The latency is the same for one or two cycle instructions. Individual interrupt flag bits are set, regardless of the status of their corresponding mask bit, PEIE bit, or the GIE bit.
1. An instruction clears the GIE bit while an interrupt is acknowledged. 2. The program branches to the interrupt vector and executes the Interrupt Service Routine. 3. The Interrupt Service Routine completes the execution of the RETFIE instruction. This causes the GIE bit to be set (enables interrupts), and the program returns to the instruction after the one which was meant to disable interrupts. Perform the following to ensure that interrupts are globally disabled:
LOOP BCF INTCON, GIE ; ; ; ; ; ; ; ; Disable global interrupt bit Global interrupt disabled? NO, try again Yes, continue with program flow
BTFSC INTCON, GIE GOTO : LOOP
2000 Microchip Technology Inc.
DS30605C-page 93
PIC16C63A/65B/73B/74B
FIGURE 13-5:
PSPIF PSPIE ADIF ADIE RCIF RCIE TXIF TXIE SSPIF SSPIE CCP1IF CCP1IE TMR2IF TMR2IE TMR1IF TMR1IE CCP2IF CCP2IE T0IF T0IE INTF INTE RBIF RBIE PEIE GIE Wake-up (If in SLEEP mode)
INTERRUPT LOGIC
Interrupt to CPU
The following table shows which devices have which interrupts. Device PIC16C63A PIC16C65B PIC16C73B PIC16C74B T0IF Yes Yes Yes Yes INTF Yes Yes Yes Yes RBIF Yes Yes Yes Yes PSPIF - Yes - Yes ADIF - - Yes Yes RCIF Yes Yes Yes Yes TXIF Yes Yes Yes Yes SSPIF Yes Yes Yes Yes CCP1IF Yes Yes Yes Yes TMR2IF Yes Yes Yes Yes TMR1IF Yes Yes Yes Yes CCP2IF Yes Yes Yes Yes
13.5.1
INT INTERRUPT
13.5.3
PORTB INTERRUPT-ON-CHANGE
The external interrupt on RB0/INT pin is edge triggered: either rising if bit INTEDG (OPTION_REG<6>) is set, or falling if the INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, flag bit INTF (INTCON<1>) is set. This interrupt can be disabled by clearing enable bit INTE (INTCON<4>). Flag bit INTF must be cleared in software in the Interrupt Service Routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if bit INTE was set prior to going into SLEEP. The status of global interrupt enable bit GIE decides whether or not the processor branches to the interrupt vector following wakeup. See Section 13.8 for details on SLEEP mode.
An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<4>). (Section 5.2) Note: If a change on the I/O pin should occur when the read operation is being executed (start of the Q2 cycle), then the RBIF interrupt flag may not get set.
13.5.2
TMR0 INTERRUPT
An overflow (FFh 00h) in the TMR0 register will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>) (see Section 6.0).
DS30605C-page 94
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
13.6 Context Saving During Interrupts
The example: a) b) c) d) e) f) Stores the W register. Stores the STATUS register in bank 0. Stores the PCLATH register. Executes the ISR code. Restores the STATUS register (and bank select bit). Restores the W and PCLATH registers. During an interrupt, only the return PC value is saved on the stack. Users may wish to save key registers during an interrupt i.e., W register and STATUS register. This will have to be implemented in software. Example 13-1 stores and restores the STATUS, W, and PCLATH registers. The register W_TEMP must be defined in each bank and must be defined at the same offset from the bank base address (i.e., if W_TEMP is defined at 0x20 in bank 0, it must also be defined at 0xA0 in bank 1).
EXAMPLE 13-1:
MOVWF SWAPF CLRF MOVWF MOVF MOVWF : (ISR) : MOVF MOVWF SWAPF MOVWF SWAPF SWAPF
SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
;Copy ;Swap ;bank ;Save ;Only ;Save W to TEMP register, could be bank one or zero status to be saved into W 0, regardless of current bank, Clears IRP,RP1,RP0 status to bank zero STATUS_TEMP register required if using pages 1, 2 and/or 3 PCLATH into W
W_TEMP STATUS,W STATUS STATUS_TEMP PCLATH, W PCLATH_TEMP
;User ISR code goes here PCLATH_TEMP, W PCLATH STATUS_TEMP, W STATUS W_TEMP,F W_TEMP,W ;Restore PCLATH ;Move W into PCLATH ;Swap STATUS_TEMP register into W ;(sets bank to original state) ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W
13.7
Watchdog Timer (WDT)
13.7.1
WDT PERIOD
The Watchdog Timer is a free running on-chip RC oscillator, which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. The WDT will run, even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device has been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device RESET (Watchdog Timer Reset). If the device is in SLEEP mode, a WDT time-out causes the device to wake-up and resume normal operation (Watchdog Timer Wake-up). The WDT can be permanently disabled by clearing configuration bit WDTE (Section 13.1).
The WDT has a nominal time-out period of 18 ms (parameter #31, TWDT). The time-out periods vary with temperature, VDD, and process variations. If longer time-out periods are desired, a prescaler with a division ratio of up to 1:128 can be assigned to the WDT under software control, by writing to the OPTION register. Time-out periods up to 128 TWDT can be realized. The CLRWDT and SLEEP instructions clear the WDT and the postscaler, if assigned to the WDT. In addition, the SLEEP instruction prevents the WDT from generating a RESET, but will allow the WDT to wake the device from SLEEP mode. The TO bit in the STATUS register will be cleared upon a WDT time-out.
2000 Microchip Technology Inc.
DS30605C-page 95
PIC16C63A/65B/73B/74B
13.7.2 WDT PROGRAMMING CONSIDERATIONS
It should also be taken into account that under worst case conditions (VDD = Min., Temperature = Max., and max. WDT prescaler), it may take several seconds before a WDT time-out occurs. Note: When a CLRWDT instruction is executed and the prescaler is assigned to the WDT, the prescaler count will be cleared, but the prescaler assignment is not changed.
FIGURE 13-6:
WATCHDOG TIMER BLOCK DIAGRAM
From TMR0 Clock Source (Figure 6-1) 0 WDT Timer 1 M U X Postscaler 8 8 - to - 1 MUX WDT Enable Bit PSA To TMR0 MUX (Figure 6-1) 0 MUX 1 PSA PS2:PS0
WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION register.
TABLE 13-7:
Address 2007h 81h
SUMMARY OF WATCHDOG TIMER REGISTERS
Name Bit 7 - RBPU Bit 6 BODEN(1) INTEDG Bit 5 CP1 T0CS Bit 4 CP0 T0SE Bit 3 PWRTE(1) PSA Bit 2 WDTE PS2 Bit 1 FOSC1 PS1 Bit 0 FOSC0 PS0
Config. bits OPTION_REG
Legend: Shaded cells are not used by the Watchdog Timer. Note 1: See Register 13-1 for operation of these bits.
DS30605C-page 96
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
13.8 Power-down Mode (SLEEP)
Power-down mode is entered by executing a SLEEP instruction. If enabled, the WDT will be cleared but keeps running, the PD bit (STATUS<3>) is cleared, the TO (STATUS<4>) bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had, before the SLEEP instruction was executed (driving high, low, or hi-impedance). For lowest current consumption in this mode, place all I/O pins at either VDD or VSS, ensure no external circuitry is drawing current from the I/O pin, power-down the A/D, and disable external clocks. Pull all I/O pins that are hi-impedance inputs, high or low externally, to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should also be considered. The MCLR pin must be at a logic high level (VIHMC). Other peripherals cannot generate interrupts since during SLEEP, no on-chip Q clocks are present. When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction.
13.8.2
WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bit will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake up from sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction.
13.8.1
WAKE-UP FROM SLEEP
The device can wake up from SLEEP through one of the following events: 1. 2. 3. External RESET input on MCLR pin. Watchdog Timer Wake-up (if WDT was enabled). Interrupt from INT pin, RB port change or a Peripheral Interrupt.
External MCLR Reset will cause a device RESET. All other events are considered a continuation of program execution and cause a "wake-up". The TO and PD bits in the STATUS register can be used to determine the cause of device RESET. The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). The following peripheral interrupts can wake the device from SLEEP: 1. 2. 3. 4. 5. 6. 7. TMR1 interrupt. Timer1 must be operating as an asynchronous counter. SSP (START/STOP) bit detect interrupt. SSP transmit or receive in Slave mode (SPI/I2C). CCP Capture mode interrupt. Parallel Slave port read or write (PIC16C65B/74B only). A/D conversion (when A/D clock source is RC). USART TX or RX (Synchronous Slave mode).
2000 Microchip Technology Inc.
DS30605C-page 97
PIC16C63A/65B/73B/74B
FIGURE 13-7: WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT(4) INT pin INTF Flag (INTCON<1>) GIE bit (INTCON<7>) INSTRUCTION FLOW PC Instruction Fetched Instruction Executed PC Inst(PC) = SLEEP Inst(PC - 1) PC+1 Inst(PC + 1) SLEEP PC+2 PC+2 Inst(PC + 2) Inst(PC + 1) Dummy cycle PC + 2 0004h Inst(0004h) Dummy cycle 0005h Inst(0005h) Inst(0004h) Processor in SLEEP Interrupt Latency
(2)
TOST(2)
Note
1: 2: 3: 4:
XT, HS or LP oscillator mode assumed. TOST = 1024Tosc (drawing not to scale). This delay is not present in RC osc mode. GIE = '1' assumed. After wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. CLKOUT is not available in these osc modes, but shown here for timing reference.
13.9
Program Verification/Code Protection
If the code protection bit(s) have not been programmed, the on-chip program memory can be read out for verification purposes. Note: Microchip does not recommend code protecting windowed devices. Devices that are code protected may be erased, but not programmed again.
The device is placed into a Program/Verify mode by holding the RB6 and RB7 pins low, while raising the MCLR (VPP) pin from VIL to VIHH (see programming specification). RB6 becomes the programming clock and RB7 becomes the programming data. Both RB6 and RB7 are Schmitt Trigger inputs in this mode. After RESET, to place the device into Programming/ Verify mode, the program counter (PC) is at location 00h. A 6-bit command is then supplied to the device. Depending on the command, 14 bits of program data are then supplied to or from the device, depending if the command was a load or a read. For complete details of serial programming, please refer to the PIC16C6X/7X Programming Specifications (Literature #DS30228).
13.10 ID Locations
Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code identification numbers. These locations are not accessible during normal execution, but are readable and writable during program/verify. It is recommended that only the four least significant bits of the ID location are used.
FIGURE 13-8:
TYPICAL IN-CIRCUIT SERIAL PROGRAMMING CONNECTION
To Normal Connections PIC16CXX VDD VSS MCLR/VPP RB6 RB7
13.11
In-Circuit Serial Programming
PIC16CXX microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed.
External Connector Signals +5V 0V VPP CLK Data I/O
VDD To Normal Connections
DS30605C-page 98
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
14.0 INSTRUCTION SET SUMMARY
The instruction set is highly orthogonal and is grouped into three basic categories: * Byte-oriented operations * Bit-oriented operations * Literal and control operations All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. Table 14-2 lists the instructions recognized by the MPASMTM assembler. Figure 14-1 shows the general formats that the instructions can have. Note: To maintain upward compatibility with future PIC16CXX products, do not use the OPTION and TRIS instructions. Each PIC16CXX instruction is a 14-bit word divided into an OPCODE, which specifies the instruction type and one or more operands, which further specify the operation of the instruction. The PIC16CXX instruction set summary in Table 14-2 lists byte-oriented, bit-oriented, and literal and control operations. Table 14-1 shows the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the address of the file in which the bit is located. For literal and control operations, 'k' represents an eight or eleven bit constant or literal value.
TABLE 14-1:
Field
f W b k
OPCODE FIELD DESCRIPTIONS
Description
All examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit.
Register file address (0x00 to 0x7F) Working register (accumulator) Bit address within an 8-bit file register Literal field, constant data or label Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1
FIGURE 14-1:
GENERAL FORMAT FOR INSTRUCTIONS
0
Byte-oriented file register operations 13 876 OPCODE d f (FILE #) d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 76 OPCODE b (BIT #) f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 OPCODE k = 8-bit immediate value
CALL and GOTO instructions only
x
d
label Label name TOS PC
0
Top-of-Stack Program Counter
PCLATH Program Counter High Latch
GIE WDT TO PD dest []
Global Interrupt Enable bit Watchdog Timer/Counter Time-out bit Power-down bit Destination either the W register or the specified register file location Options Contents Assigned to Register bit field In the set of
8
7 k (literal)
0
() <>
13
11 OPCODE
10 k (literal)
0
k = 11-bit immediate value
italics User defined term (font is courier)
2000 Microchip Technology Inc.
DS30605C-page 99
PIC16C63A/65B/73B/74B
TABLE 14-2:
Mnemonic, Operands
PIC16CXX INSTRUCTION SET
Description Cycles MSb 14-Bit Opcode LSb Status Affected Notes
BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f f, d f, d f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0000 dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff 0011 ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff
C,DC,Z Z Z Z Z Z Z Z Z
1,2 1,2 2 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2
C C C,DC,Z Z
1,2 1,2 1,2 1,2 1,2
BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set 1 1 1 (2) 1 (2)
01 01 01 01 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff
1,2 1,2 3 3
LITERAL AND CONTROL OPERATIONS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW k k k k k k k k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into standby mode Subtract W from literal Exclusive OR literal with W 1 1 2 1 2 1 1 2 2 2 1 1 1
11 11 10 00 10 11 11 00 11 00 00 11 11 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk
C,DC,Z Z TO,PD Z
TO,PD C,DC,Z Z
Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP.
Note:
Additional information on the mid-range instruction set is available in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023).
DS30605C-page 100
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
14.1
ADDLW Syntax: Operands: Operation: Status Affected: Description:
Instruction Descriptions
Add Literal and W [label] ADDLW 0 k 255 (W) + k (W) C, DC, Z
The contents of the W register are added to the eight bit literal 'k' and the result is placed in the W register.
ANDWF Syntax: Operands: Operation: Status Affected: Description:
AND W with f [label] ANDWF 0 f 127 d [0,1] (W) .AND. (f) (destination) Z
AND the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
k
f,d
ADDWF Syntax: Operands: Operation: Status Affected: Description:
Add W and f [label] ADDWF 0 f 127 d [0,1] (W) + (f) (destination) C, DC, Z
Add the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
BCF f,d Syntax: Operands: Operation: Status Affected: Description:
Bit Clear f [label] BCF 0 f 127 0b7 0 (f) None
Bit 'b' in register 'f' is cleared.
f,b
ANDLW Syntax: Operands: Operation: Status Affected: Description:
AND Literal with W [label] ANDLW 0 k 255 (W) .AND. (k) (W) Z
The contents of W register are AND'ed with the eight bit literal 'k'. The result is placed in the W register.
BSF Syntax: Operands: Operation: Status Affected: Description:
Bit Set f [label] BSF 0 f 127 0b7 1 (f) None
Bit 'b' in register 'f' is set.
k
f,b
2000 Microchip Technology Inc.
DS30605C-page 101
PIC16C63A/65B/73B/74B
BTFSS Syntax: Operands: Operation: Status Affected: Description: Bit Test f, Skip if Set [label] BTFSS f,b 0 f 127 0b<7 skip if (f) = 1 None
If bit 'b' in register 'f' is '0', the next instruction is executed. If bit 'b' is '1', then the next instruction is discarded and a NOP is executed instead making this a 2TCY instruction.
CLRF Syntax: Operands: Operation: Status Affected: Description:
Clear f [label] CLRF 0 f 127 00h (f) 1Z Z
The contents of register 'f' are cleared and the Z bit is set.
f
BTFSC Syntax: Operands: Operation: Status Affected: Description:
Bit Test, Skip if Clear [label] BTFSC f,b 0 f 127 0b7 skip if (f) = 0 None
If bit 'b' in register 'f' is '1', the next instruction is executed. If bit 'b', in register 'f', is '0', the next instruction is discarded, and a NOP is executed instead, making this a 2 TCY instruction.
CLRW Syntax: Operands: Operation: Status Affected: Description:
Clear W [ label ] CLRW None 00h (W) 1Z Z
W register is cleared. Zero bit (Z) is set.
CALL Syntax: Operands: Operation:
Call Subroutine [ label ] CALL k 0 k 2047 (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> None
Call Subroutine. First, return address (PC+1) is pushed onto the stack. The eleven bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two-cycle instruction.
CLRWDT Syntax: Operands: Operation:
Clear Watchdog Timer [ label ] CLRWDT None 00h WDT 0 WDT prescaler, 1 TO 1 PD TO, PD
CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set.
Status Affected: Description:
Status Affected: Description:
DS30605C-page 102
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
COMF Syntax: Operands: Operation: Status Affected: Description: Complement f [ label ] COMF 0 f 127 d [0,1] (f) (destination) Z
The contents of register 'f' are complemented. If 'd' is 0, the result is stored in W. If 'd' is 1, the result is stored back in register 'f'.
GOTO f,d Syntax: Operands: Operation: Status Affected: Description:
Unconditional Branch [ label ] GOTO k 0 k 2047 k PC<10:0> PCLATH<4:3> PC<12:11> None
GOTO is an unconditional branch. The eleven bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two-cycle instruction.
DECF Syntax: Operands: Operation: Status Affected: Description:
Decrement f [label] DECF f,d 0 f 127 d [0,1] (f) - 1 (destination) Z
Decrement register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
INCF Syntax: Operands: Operation: Status Affected: Description:
Increment f [ label ] INCF f,d 0 f 127 d [0,1] (f) + 1 (destination) Z
The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'.
DECFSZ Syntax: Operands: Operation: Status Affected: Description:
Decrement f, Skip if 0 [ label ] DECFSZ f,d 0 f 127 d [0,1] (f) - 1 (destination); skip if result = 0 None
The contents of register 'f' are decremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, then a NOP is executed instead making it a 2 TCY instruction.
INCFSZ Syntax: Operands: Operation: Status Affected: Description:
Increment f, Skip if 0 [ label ] INCFSZ f,d 0 f 127 d [0,1] (f) + 1 (destination), skip if result = 0 None
The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, a NOP is executed instead making it a 2 TCY instruction.
2000 Microchip Technology Inc.
DS30605C-page 103
PIC16C63A/65B/73B/74B
IORLW Syntax: Operands: Operation: Status Affected: Description: Inclusive OR Literal with W [ label ] IORLW k 0 k 255 (W) .OR. k (W) Z
The contents of the W register are OR'ed with the eight bit literal 'k'. The result is placed in the W register.
MOVLW Syntax: Operands: Operation: Status Affected: Description:
Move Literal to W [ label ] k (W) None
The eight bit literal 'k' is loaded into W register. The don't cares will assemble as 0's.
MOVLW k
0 k 255
IORWF Syntax: Operands: Operation: Status Affected: Description:
Inclusive OR W with f [ label ] IORWF f,d 0 f 127 d [0,1] (W) .OR. (f) (destination) Z
Inclusive OR the W register with register 'f'. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed back in register 'f'.
MOVWF Syntax: Operands: Operation: Status Affected: Description:
Move W to f [ label ] (W) (f) None
Move data from W register to register 'f'.
MOVWF
f
0 f 127
MOVF Syntax: Operands: Operation: Status Affected: Description:
Move f [ label ] MOVF f,d 0 f 127 d [0,1] (f) (destination) Z
The contents of register f are moved to a destination dependant upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register since status flag Z is affected.
NOP Syntax: Operands: Operation: Status Affected: Description:
No Operation [ label ] None No operation None
No operation.
NOP
DS30605C-page 104
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
RETFIE Syntax: Operands: Operation: Status Affected: Return from Interrupt [ label ] None TOS PC, 1 GIE
None
RLF Syntax: Operands: Operation: Status Affected: Description:
Rotate Left f through Carry [ label ] RLF f,d 0 f 127 d [0,1] See description below C
The contents of register 'f' are rotated one bit to the left through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is stored back in register 'f'. C Register f
RETFIE
RETLW Syntax: Operands: Operation: Status Affected: Description:
Return with Literal in W [ label ] RETLW k 0 k 255 k (W); TOS PC None
The W register is loaded with the eight bit literal 'k'. The program counter is loaded from the top of the stack (the return address). This is a two-cycle instruction.
RRF Syntax: Operands: Operation: Status Affected: Description:
Rotate Right f through Carry [ label ] RRF f,d 0 f 127 d [0,1] See description below C
The contents of register 'f' are rotated one bit to the right through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. C Register f
RETURN Syntax: Operands: Operation: Status Affected: Description:
Return from Subroutine [ label ] None TOS PC None
Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two-cycle instruction.
SLEEP Syntax: Operands: Operation: [ label ] SLEEP None 00h WDT, 0 WDT prescaler, 1 TO, 0 PD TO, PD
The power-down status bit, PD is cleared. Time-out status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into SLEEP mode with the oscillator stopped. See Section 13.8 for more details.
RETURN
Status Affected: Description:
2000 Microchip Technology Inc.
DS30605C-page 105
PIC16C63A/65B/73B/74B
SUBLW Syntax: Operands: Operation: Description: Subtract W from Literal [ label ] SUBLW k 0 k 255 k - (W) (W)
The W register is subtracted (2's complement method) from the eight bit literal 'k'. The result is placed in the W register.
XORLW Syntax: Operands: Operation: Status Affected: Description:
Exclusive OR Literal with W [label] XORLW k 0 k 255 (W) .XOR. k (W) Z
The contents of the W register are XOR'ed with the eight bit literal 'k'. The result is placed in the W register.
Status Affected: C, DC, Z
SUBWF Syntax: Operands: Operation: Description:
Subtract W from f [ label ] SUBWF f,d 0 f 127 d [0,1] (f) - (W) (destination)
Subtract (2's complement method) W register from register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
XORWF Syntax: Operands: Operation: Status Affected: Description:
Exclusive OR W with f [label] XORWF f,d 0 f 127 d [0,1] (W) .XOR. (f) (destination) Z
Exclusive OR the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
Status Affected: C, DC, Z
SWAPF Syntax: Operands: Operation: Status Affected: Description:
Swap Nibbles in f [ label ] SWAPF f,d 0 f 127 d [0,1] (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) None
The upper and lower nibbles of register 'f' are exchanged. If 'd' is 0, the result is placed in W register. If 'd' is 1, the result is placed in register 'f'.
DS30605C-page 106
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
15.0 DEVELOPMENT SUPPORT
The MPLAB IDE allows you to: * Edit your source files (either assembly or `C') * One touch assemble (or compile) and download to PICmicro emulator and simulator tools (automatically updates all project information) * Debug using: - source files - absolute listing file - machine code The ability to use MPLAB IDE with multiple debugging tools allows users to easily switch from the costeffective simulator to a full-featured emulator with minimal retraining. The PICmicro(R) microcontrollers are supported with a full range of hardware and software development tools: * Integrated Development Environment - MPLAB(R) IDE Software * Assemblers/Compilers/Linkers - MPASMTM Assembler - MPLAB C17 and MPLAB C18 C Compilers - MPLINKTM Object Linker/ MPLIBTM Object Librarian * Simulators - MPLAB SIM Software Simulator * Emulators - MPLAB ICE 2000 In-Circuit Emulator - ICEPICTM In-Circuit Emulator * In-Circuit Debugger - MPLAB ICD for PIC16F87X * Device Programmers - PRO MATE(R) II Universal Device Programmer - PICSTART(R) Plus Entry-Level Development Programmer * Low Cost Demonstration Boards - PICDEMTM 1 Demonstration Board - PICDEM 2 Demonstration Board - PICDEM 3 Demonstration Board - PICDEM 17 Demonstration Board - KEELOQ(R) Demonstration Board
15.2
MPASM Assembler
The MPASM assembler is a full-featured universal macro assembler for all PICmicro MCU's. The MPASM assembler has a command line interface and a Windows shell. It can be used as a stand-alone application on a Windows 3.x or greater system, or it can be used through MPLAB IDE. The MPASM assembler generates relocatable object files for the MPLINK object linker, Intel(R) standard HEX files, MAP files to detail memory usage and symbol reference, an absolute LST file that contains source lines and generated machine code, and a COD file for debugging. The MPASM assembler features include: * Integration into MPLAB IDE projects. * User-defined macros to streamline assembly code. * Conditional assembly for multi-purpose source files. * Directives that allow complete control over the assembly process.
15.1
MPLAB Integrated Development Environment Software
The MPLAB IDE software brings an ease of software development previously unseen in the 8-bit microcontroller market. The MPLAB IDE is a Windows(R)-based application that contains: * An interface to debugging tools - simulator - programmer (sold separately) - emulator (sold separately) - in-circuit debugger (sold separately) * A full-featured editor * A project manager * Customizable toolbar and key mapping * A status bar * On-line help
15.3
MPLAB C17 and MPLAB C18 C Compilers
The MPLAB C17 and MPLAB C18 Code Development Systems are complete ANSI `C' compilers for Microchip's PIC17CXXX and PIC18CXXX family of microcontrollers, respectively. These compilers provide powerful integration capabilities and ease of use not found with other compilers. For easier source level debugging, the compilers provide symbol information that is compatible with the MPLAB IDE memory display.
2000 Microchip Technology Inc.
DS30605C-page 107
PIC16C63A/65B/73B/74B
15.4 MPLINK Object Linker/ MPLIB Object Librarian 15.6 MPLAB ICE High Performance Universal In-Circuit Emulator with MPLAB IDE
The MPLINK object linker combines relocatable objects created by the MPASM assembler and the MPLAB C17 and MPLAB C18 C compilers. It can also link relocatable objects from pre-compiled libraries, using directives from a linker script. The MPLIB object librarian is a librarian for precompiled code to be used with the MPLINK object linker. When a routine from a library is called from another source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The MPLIB object librarian manages the creation and modification of library files. The MPLINK object linker features include: * Integration with MPASM assembler and MPLAB C17 and MPLAB C18 C compilers. * Allows all memory areas to be defined as sections to provide link-time flexibility. The MPLIB object librarian features include: * Easier linking because single libraries can be included instead of many smaller files. * Helps keep code maintainable by grouping related modules together. * Allows libraries to be created and modules to be added, listed, replaced, deleted or extracted.
The MPLAB ICE universal in-circuit emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PICmicro microcontrollers (MCUs). Software control of the MPLAB ICE in-circuit emulator is provided by the MPLAB Integrated Development Environment (IDE), which allows editing, building, downloading and source debugging from a single environment. The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring features. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The universal architecture of the MPLAB ICE in-circuit emulator allows expansion to support new PICmicro microcontrollers. The MPLAB ICE in-circuit emulator system has been designed as a real-time emulation system, with advanced features that are generally found on more expensive development tools. The PC platform and Microsoft(R) Windows environment were chosen to best make these features available to you, the end user.
15.7
ICEPIC In-Circuit Emulator
15.5
MPLAB SIM Software Simulator
The MPLAB SIM software simulator allows code development in a PC-hosted environment by simulating the PICmicro series microcontrollers on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a file, or user-defined key press, to any of the pins. The execution can be performed in single step, execute until break, or trace mode. The MPLAB SIM simulator fully supports symbolic debugging using the MPLAB C17 and the MPLAB C18 C compilers and the MPASM assembler. The software simulator offers the flexibility to develop and debug code outside of the laboratory environment, making it an excellent multiproject software development tool.
The ICEPIC low cost, in-circuit emulator is a solution for the Microchip Technology PIC16C5X, PIC16C6X, PIC16C7X and PIC16CXXX families of 8-bit OneTime-Programmable (OTP) microcontrollers. The modular system can support different subsets of PIC16C5X or PIC16CXXX products through the use of interchangeable personality modules, or daughter boards. The emulator is capable of emulating without target application circuitry being present.
DS30605C-page 108
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
15.8 MPLAB ICD In-Circuit Debugger
Microchip's In-Circuit Debugger, MPLAB ICD, is a powerful, low cost, run-time development tool. This tool is based on the FLASH PIC16F87X and can be used to develop for this and other PICmicro microcontrollers from the PIC16CXXX family. The MPLAB ICD utilizes the in-circuit debugging capability built into the PIC16F87X. This feature, along with Microchip's In-Circuit Serial ProgrammingTM protocol, offers costeffective in-circuit FLASH debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by watching variables, singlestepping and setting break points. Running at full speed enables testing hardware in real-time.
15.11 PICDEM 1 Low Cost PICmicro Demonstration Board
The PICDEM 1 demonstration board is a simple board which demonstrates the capabilities of several of Microchip's microcontrollers. The microcontrollers supported are: PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The user can program the sample microcontrollers provided with the PICDEM 1 demonstration board on a PRO MATE II device programmer, or a PICSTART Plus development programmer, and easily test firmware. The user can also connect the PICDEM 1 demonstration board to the MPLAB ICE incircuit emulator and download the firmware to the emulator for testing. A prototype area is available for the user to build some additional hardware and connect it to the microcontroller socket(s). Some of the features include an RS-232 interface, a potentiometer for simulated analog input, push button switches and eight LEDs connected to PORTB.
15.9
PRO MATE II Universal Device Programmer
The PRO MATE II universal device programmer is a full-featured programmer, capable of operating in stand-alone mode, as well as PC-hosted mode. The PRO MATE II device programmer is CE compliant. The PRO MATE II device programmer has programmable VDD and VPP supplies, which allow it to verify programmed memory at VDD min and VDD max for maximum reliability. It has an LCD display for instructions and error messages, keys to enter commands and a modular detachable socket assembly to support various package types. In stand-alone mode, the PRO MATE II device programmer can read, verify, or program PICmicro devices. It can also set code protection in this mode.
15.12 PICDEM 2 Low Cost PIC16CXX Demonstration Board
The PICDEM 2 demonstration board is a simple demonstration board that supports the PIC16C62, PIC16C64, PIC16C65, PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM 2 demonstration board on a PRO MATE II device programmer, or a PICSTART Plus development programmer, and easily test firmware. The MPLAB ICE in-circuit emulator may also be used with the PICDEM 2 demonstration board to test firmware. A prototype area has been provided to the user for adding additional hardware and connecting it to the microcontroller socket(s). Some of the features include a RS-232 interface, push button switches, a potentiometer for simulated analog input, a serial EEPROM to demonstrate usage of the I2CTM bus and separate headers for connection to an LCD module and a keypad.
15.10 PICSTART Plus Entry Level Development Programmer
The PICSTART Plus development programmer is an easy-to-use, low cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. The PICSTART Plus development programmer supports all PICmicro devices with up to 40 pins. Larger pin count devices, such as the PIC16C92X and PIC17C76X, may be supported with an adapter socket. The PICSTART Plus development programmer is CE compliant.
2000 Microchip Technology Inc.
DS30605C-page 109
PIC16C63A/65B/73B/74B
15.13 PICDEM 3 Low Cost PIC16CXXX Demonstration Board
The PICDEM 3 demonstration board is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC package. It will also support future 44-pin PLCC microcontrollers with an LCD Module. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM 3 demonstration board on a PRO MATE II device programmer, or a PICSTART Plus development programmer with an adapter socket, and easily test firmware. The MPLAB ICE in-circuit emulator may also be used with the PICDEM 3 demonstration board to test firmware. A prototype area has been provided to the user for adding hardware and connecting it to the microcontroller socket(s). Some of the features include a RS-232 interface, push button switches, a potentiometer for simulated analog input, a thermistor and separate headers for connection to an external LCD module and a keypad. Also provided on the PICDEM 3 demonstration board is a LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature and day of the week. The PICDEM 3 demonstration board provides an additional RS-232 interface and Windows software for showing the demultiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware demultiplexer for the LCD signals.
15.14 PICDEM 17 Demonstration Board
The PICDEM 17 demonstration board is an evaluation board that demonstrates the capabilities of several Microchip microcontrollers, including PIC17C752, PIC17C756A, PIC17C762 and PIC17C766. All necessary hardware is included to run basic demo programs, which are supplied on a 3.5-inch disk. A programmed sample is included and the user may erase it and program it with the other sample programs using the PRO MATE II device programmer, or the PICSTART Plus development programmer, and easily debug and test the sample code. In addition, the PICDEM 17 demonstration board supports downloading of programs to and executing out of external FLASH memory on board. The PICDEM 17 demonstration board is also usable with the MPLAB ICE in-circuit emulator, or the PICMASTER emulator and all of the sample programs can be run and modified using either emulator. Additionally, a generous prototype area is available for user hardware.
15.15 KEELOQ Evaluation and Programming Tools
KEELOQ evaluation and programming tools support Microchip's HCS Secure Data Products. The HCS evaluation kit includes a LCD display to show changing codes, a decoder to decode transmissions and a programming interface to program test transmitters.
DS30605C-page 110
2000 Microchip Technology Inc.
24CXX/ 25CXX/ 93CXX
PIC14000
HCSXXX
PIC16C5X
PIC16C6X
PIC16C7X
PIC16C8X
PIC17C4X
PIC16F62X
PIC16C7XX
PIC16F8XX
PIC16C9XX
PIC17C7XX
PIC12CXXX
PIC16CXXX
PIC18CXX2
MCRFXXX
MCP2510
TABLE 15-1:
MPLAB(R) Integrated Development Environment
a
a
a
a
a
a
a
a
a
a
a
a
aa
aa
MPLAB(R) C17 C Compiler
Software Tools
MPLAB(R) C18 C Compiler
MPASMTM Assembler/ MPLINKTM Object Linker
a
a
Programmers Debugger Emulators
Demo Boards and Eval Kits
2000 Microchip Technology Inc.
aaa
aa
**
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
aa
MPLAB(R) ICE In-Circuit Emulator
ICEPICTM In-Circuit Emulator
a
* *
a
a
a
a
a
a
a
MPLAB(R) ICD In-Circuit Debugger
a
**
a
a
PICSTART(R) Plus Entry Level Development Programmer
a
**
a
a
a
a
a
a
a
a
a
a
a
a
a
PRO MATE(R) II Universal Device Programmer
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PICDEMTM 1 Demonstration Board
a

a
a
a
a
DEVELOPMENT TOOLS FROM MICROCHIP
PICDEMTM 2 Demonstration Board
a
a
a
PICDEMTM 3 Demonstration Board
a
PICDEMTM 14A Demonstration Board
a
PICDEMTM 17 Demonstration Board
a
KEELOQ(R) Evaluation Kit
aa
KEELOQ(R) Transponder Kit
microIDTM Programmer's Kit
aa
125 kHz microIDTM Developer's Kit
125 kHz Anticollision microIDTM Developer's Kit
a
13.56 MHz Anticollision microIDTM Developer's Kit
a
PIC16C63A/65B/73B/74B
DS30605C-page 111
MCP2510 CAN Developer's Kit
* Contact the Microchip Technology Inc. web site at www.microchip.com for information on how to use the MPLAB(R) ICD In-Circuit Debugger (DV164001) with PIC16C62, 63, 64, 65, 72, 73, 74, 76, 77. ** Contact Microchip Technology Inc. for availability date. Development tool is available on select devices.
a
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 112
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
16.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings() Ambient temperature under bias.............................................................................................................-55C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on any pin with respect to VSS (except VDD, MCLR and RA4) .......................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2) ......................................................................................... 0V to +13.25V Voltage on RA4 with respect to VSS............................................................................................................... 0V to +8.5V Total power dissipation (Note 1) ...............................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD) .......................................................................................................... 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ...................................................................................................20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by PORTA, PORTB, and PORTE (Note 3) (combined)...................................................200 mA Maximum current sourced by PORTA, PORTB, and PORTE (Note 3) (combined)..............................................200 mA Maximum current sunk by PORTC and PORTD (Note 3) (combined)..................................................................200 mA Maximum current sourced by PORTC and PORTD (Note 3) (combined).............................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD-VOH) x IOH} + (VOl x IOL) 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50 - 100 should be used when applying a "low" level to the MCLR/VPP pin rather than pulling this pin directly to VSS. 3: PORTD and PORTE not available on the PIC16C63A/73B. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
2000 Microchip Technology Inc.
DS30605C-page 113
PIC16C63A/65B/73B/74B
FIGURE 16-1: PIC16C63A/65B/73B/74B VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V PIC16CXXX-20
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V
20 MHz
Frequency
FIGURE 16-2:
PIC16LC63A/65B/73B/74B VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V
PIC16LCXXX-04
4 MHz
10 MHz
Frequency
FMAX = (12.0 MHz/V) (VDDAPPMIN - 2.5 V) + 4 MHz Note 1: VDDAPPMIN is the minimum voltage of the PICmicro(R) device in the application. Note 2: FMAX has a maximum frequency of 10MHz.
DS30605C-page 114
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 16-3: PIC16C63A/65B/73B/74B VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V PIC16CXXX-04
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V
4 MHz
Frequency
2000 Microchip Technology Inc.
DS30605C-page 115
PIC16C63A/65B/73B/74B
16.1 DC Characteristics
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions PIC16LC63A/65B/73B/74B-04
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym VDD
Characteristic Supply Voltage PIC16LCXXX PIC16CXXX
D001 D001 D001A D002* D003 VDR
2.5 VBOR* 4.0 4.5 VBOR* - -
- - - - - 1.5 VSS
5.5 5.5 5.5 5.5 5.5 - -
V V V V V V V
LP, XT, RC osc modes (DC - 4 MHz) BOR enabled (Note 7) XT, RC and LP osc mode HS osc mode BOR enabled (Note 7)
RAM Data Retention Voltage (Note 1)
VPOR VDD Start Voltage to ensure internal Power-on Reset signal
See section on Power-on Reset for details
D004* SVDD VDD Rise Rate to ensure internal D004A* Power-on Reset signal D005 VBOR Brown-out Reset voltage trip point
0.05 TBD 3.65
- - -
- - 4.35
V/mS PWRT enabled (PWRTE bit clear) V/mS PWRT disabled (PWRTE bit set) See section on Power-on Reset for details V BODEN bit set
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
DS30605C-page 116
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
PIC16LC63A/65B/73B/74B-04 Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym IDD
Characteristic
Supply Current (Notes 2, 5) PIC16LCXXX - - PIC16CXXX - - 0.6 22.5 2.7 7 2.0 48 5 10 mA A mA mA XT, RC osc modes: FOSC = 4 MHz, VDD = 3.0V (Note 4) LP osc mode: FOSC = 32 kHz, VDD = 3.0V, WDT disabled XT, RC osc modes: FOSC = 4 MHz, VDD = 5.5 V (Note 4) HS osc mode: FOSC = 20 MHz, VDD = 5.5 V
D010 D010A D010 D013 IPD D020 D021 D021A D020 D021 D021A D021B
Power-down Current (Notes 3, 5) PIC16LCXXX - - - - - - - 7.5 0.9 0.9 10.5 1.5 1.5 2.5 20 3 3 42 16 19 19 A A A A A A A VDD = 3.0V, WDT enabled, -40C to +85C VDD = 3.0V, WDT disabled, 0C to +70C VDD = 3.0V, WDT disabled, -40C to +85C VDD = 4.0V, WDT enabled, -40C to +85C VDD = 4.0V, WDT disabled, 0C to +70C VDD = 4.0V, WDT disabled, -40C to +85C VDD = 4.0V, WDT disabled, -40C to +125C
PIC16CXXX
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
2000 Microchip Technology Inc.
DS30605C-page 117
PIC16C63A/65B/73B/74B
PIC16LC63A/65B/73B/74B-04 Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym
Characteristic Module Differential Current (Note 6)
D022*
IWDT Watchdog Timer Input Low Voltage VIL I/O ports with TTL buffer with Schmitt Trigger buffer MCLR, OSC1 (in RC mode) OSC1 (in XT, HS, and LP modes)
- -
6.0 100
20 150
A A
WDTE bit set, VDD = 4.0V BODEN bit set, VDD = 5.0
D022A* IBOR Brown-out Reset
D030 D030A D031 D032 D033
VSS VSS VSS Vss Vss
- - - - -
0.15 VDD 0.8V 0.2 VDD 0.2 VDD 0.3 VDD
V V V V V
For entire VDD range 4.5V VDD 5.5V
(Note 8)
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
DS30605C-page 118
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
PIC16LC63A/65B/73B/74B-04 Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym
Characteristic Input High Voltage
VIH D040 D040A D041 D042 D042A D043
I/O ports with TTL buffer
2.0
- - - - - -
VDD VDD VDD VDD VDD VDD
V V V V V V
4.5 V VDD 5.5V For entire VDD range For entire VDD range
0.25 VDD +
0.8V
with Schmitt Trigger buffer MCLR OSC1 (in XT, HS, and LP modes) OSC1 (in RC mode) Input Leakage Current (Notes 9, 10)
0.8 VDD 0.8 VDD 0.7 VDD 0.9 VDD
(Note 8)
D060 D061 D063 D070
IIL
I/O ports MCLR, RA4/T0CKI OSC1
- - - 50
- - - 250
1 5 5 400
A A A A
Vss VPIN VDD, Pin at hi-impedance Vss VPIN VDD Vss VPIN VDD, XT, HS and LP osc modes VDD = 5V, VPIN = VSS
IPURB PORTB Weak Pull-up Current
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
2000 Microchip Technology Inc.
DS30605C-page 119
PIC16C63A/65B/73B/74B
PIC16LC63A/65B/73B/74B-04 Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym
Characteristic Output Low Voltage
D080
VOL
I/O ports
- -
- - - -
0.6 0.6 0.6 0.6
V V V V
IOL = 8.5 mA, VDD = 4.5V, -40C to +85C IOL = 7.0 mA, VDD = 4.5V, -40C to +125C IOL = 1.6 mA, VDD = 4.5V, -40C to +85C IOL = 1.2 mA, VDD = 4.5V, -40C to +125C
D083
OSC2/CLKOUT (RC osc mode)
- -
Output High Voltage D090 VOH I/O ports (Note 10) VDD-0.7 VDD-0.7 D092 OSC2/CLKOUT (RC osc mode) VDD-0.7 VDD-0.7 D150* VOD Open-Drain High Voltage - - - - - - - - - - 8.5 V V V V V IOH = -3.0 mA, VDD = 4.5V, -40C to +85C IOH = -2.5 mA, VDD = 4.5V, -40C to +125C IOH = -1.3 mA, VDD = 4.5V, -40C to +85C IOH = -1.0 mA, VDD = 4.5V, -40C to +125C RA4 pin
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
DS30605C-page 120
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
PIC16LC63A/65B/73B/74B-04 Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min Typ Max Units Conditions
PIC16C63A/65B/73B/74B-04 PIC16C6A/65B/73B/74B-20
Param No.
Sym
Characteristic Capacitive Loading Specs on Output Pins
D100 D101 D102
COSC2 OSC2 pin CIO Cb All I/O pins and OSC2 (in RC mode) SCL, SDA (in I2C mode)
- - -
- - -
15 50 400
pF pF pF
In XT, HS and LP modes when external clock is used to drive OSC1
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When specification values of standard devices differ from those of extended voltage devices, they are shown in gray. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through REXT is not included. The current through the resistor can be estimated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: When BOR is enabled, the device will operate correctly until the VBOR voltage trip point is reached. 8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro device be driven with external clock in RC mode. 9: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 10: Negative current is defined as current sourced by the pin.
2000 Microchip Technology Inc.
DS30605C-page 121
PIC16C63A/65B/73B/74B
16.2
16.2.1
AC (Timing) Characteristics
TIMING PARAMETER SYMBOLOGY
The timing parameter symbols have been created following one of the following formats:
1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (Hi-impedance) L Low I2C only AA BUF output access Bus free
3. TCC:ST 4. Ts T
(I2C specifications only) (I2C specifications only) Time
osc rd rw sc ss t0 t1 wr
OSC1 RD RD or WR SCK SS T0CKI T1CKI WR
P R V Z High Low
Period Rise Valid Hi-impedance High Low
TCC:ST (I2C specifications only) CC HD Hold ST DAT DATA input hold STA START condition
SU STO
Setup STOP condition
DS30605C-page 122
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
16.2.2 TIMING CONDITIONS
The temperature and voltages specified in Table 16-1 apply to all timing specifications unless otherwise noted. Figure 16-4 specifies the load conditions for the timing specifications.
TABLE 16-1:
TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Operating voltage VDD range as described in DC spec Section 16.1. LC parts operate for commercial/industrial temperatures only.
AC CHARACTERISTICS
FIGURE 16-4:
LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1 VDD/2 CL VSS Pin VSS CL RL = 464 CL = 50 pF CL = 15 pF for all pins except OSC2/CLKOUT but including D and E outputs as ports for OSC2 output Load condition 2
RL
Pin
Note 1: PORTD and PORTE are not implemented on the PIC16C63A/73B.
2000 Microchip Technology Inc.
DS30605C-page 123
PIC16C63A/65B/73B/74B
16.2.3 TIMING DIAGRAMS AND SPECIFICATIONS EXTERNAL CLOCK TIMING
Q4 Q1 Q2 Q3 Q4 Q1
FIGURE 16-5:
OSC1
1 2 3 3 4 4
CLKOUT
TABLE 16-2:
Param No. 1A Sym
EXTERNAL CLOCK TIMING REQUIREMENTS
Characteristic Min DC DC DC DC Oscillator Frequency (Note 1) DC 0.1 4 5 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max 4 4 20 200 4 4 20 200 -- -- -- -- -- 10,000 250 250 -- DC -- -- -- 25 50 15 Units MHz MHz MHz kHz MHz MHz MHz kHz ns ns ns s ns ns ns ns s ns ns s ns ns ns ns Conditions RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode LP osc mode RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode TCY = 4/FOSC XT oscillator LP oscillator HS oscillator XT oscillator LP oscillator HS oscillator
FOSC External CLKIN Frequency (Note 1)
1
TOSC
External CLKIN Period (Note 1)
250 250 50 5
Oscillator Period (Note 1)
250 250 250 50 5
2 3*
TCY
Instruction Cycle Time (Note 1)
200
TosL, External Clock in (OSC1) High or 100 TosH Low Time 2.5 15 TosR, External Clock in (OSC1) Rise or TosF Fall Time -- -- --
4*
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
DS30605C-page 124
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 16-6:
OSC1 10 CLKOUT 13 14 I/O Pin (input) 17 I/O Pin (output) old value 20, 21 Refer to Figure 16-4 for load conditions. 15 new value 19 18 12 16 11
CLKOUT AND I/O TIMING
Q4 Q1 Q2 Q3
Note:
TABLE 16-3:
Param No. 10* 11* 12* 13* 14* 15* 16* 17* 18* 18A* 19* 20* 20A* 21* 21A* TosH2ioI Sym
CLKOUT AND I/O TIMING REQUIREMENTS
Characteristic OSC1 to CLKOUT Min -- -- -- -- -- TOSC + 200 0 -- 100 200 0 -- -- -- -- TCY TCY Typ 75 75 35 35 -- -- -- 50 -- -- -- 10 -- 10 -- -- -- Max 200 200 100 100 0.5TCY + 20 -- -- 150 -- -- -- 40 80 40 80 -- -- Units Conditions ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns (Note 1) (Note 1) (Note 1) (Note 1) (Note 1) (Note 1) (Note 1)
TosH2ckL
TosH2ckH OSC1 to CLKOUT TckR TckF TckL2ioV TioV2ckH TckH2ioI TosH2ioV CLKOUT rise time CLKOUT fall time CLKOUT to Port out valid Port in valid before CLKOUT Port in hold after CLKOUT OSC1 (Q1 cycle) to Port out valid OSC1 (Q2 cycle) to Port PIC16CXX input invalid (I/O in hold PIC16LCXX time) Port input valid to OSC1 (I/O in setup time) Port output rise time PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
TioV2osH TioR
TioF
Port output fall time INT pin high or low time
22* Tinp 23* Trbp
RB7:RB4 change INT high or low time
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. These parameters are asynchronous events not related to any internal clock edge. Note 1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC.
2000 Microchip Technology Inc.
DS30605C-page 125
PIC16C63A/65B/73B/74B
FIGURE 16-7: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING
VDD MCLR Internal POR 33 PWRT Time-out OSC Time-out Internal RESET Watchdog Timer Reset 34 I/O Pins Note: Refer to Figure 16-4 for load conditions. 31 34 32 30
FIGURE 16-8:
BROWN-OUT RESET TIMING
BVDD VDD 35
TABLE 16-4:
Param No. 30 31* 32 33* 34 35
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET REQUIREMENTS
Sym Characteristic Min 2 7 -- 28 -- 100 Typ -- 18 1024 TOSC 72 -- -- Max -- 33 -- 132 2.1 -- Units s ms -- ms s s VDD BVDD (D005) Conditions VDD = 5V, -40C to +125C VDD = 5V, -40C to +125C TOSC = OSC1 period VDD = 5V, -40C to +125C
TmcL MCLR Pulse Width (low) TWDT TOST Watchdog Timer Time-out Period (No Prescaler) Oscillation Start-up Timer Period
TPWRT Power-up Timer Period TIOZ TBOR I/O Hi-impedance from MCLR Low or WDT Reset Brown-out Reset Pulse Width
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
DS30605C-page 126
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 16-9:
T0CKI
TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
40 42 T1OSO/T1CKI
41
45 47 TMR0 or TMR1 Note: Refer to Figure 16-4 for load conditions.
46 48
TABLE 16-5:
Param No. Sym
TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Characteristic Min Typ Max Units Conditions
40* 41* 42*
Tt0H Tt0L Tt0P
T0CKI High Pulse Width T0CKI Low Pulse Width T0CKI Period
No Prescaler With Prescaler No Prescaler With Prescaler No Prescaler
0.5TCY + 20 10 0.5TCY + 20 10 TCY + 40
-- -- -- -- -- --
-- -- -- -- -- --
ns ns ns ns ns ns
Must also meet parameter 42 Must also meet parameter 42
With Prescaler Greater of: 20 or TCY + 40 N 45* Tt1H T1CKI High Time Synchronous, Prescaler = 1 Synchronous, PIC16CXX Prescaler = 2,4,8 PIC16LCXX Asynchronous 46* Tt1L T1CKI Low Time PIC16CXX PIC16LCXX Synchronous, Prescaler = 1 Synchronous, PIC16CXX Prescaler = 2,4,8 PIC16LCXX Asynchronous 47* Tt1P T1CKI input period Synchronous PIC16CXX PIC16LCXX PIC16CXX 0.5TCY + 20 15 25 30 50 0.5TCY + 20 15 25 30 50 Greater of: 30 or TCY + 40 N Greater of: 50 or TCY + 40 N 60 100 DC 2TOSC
N = prescale value (2, 4,..., 256) Must also meet parameter 47
-- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- --
ns ns ns ns ns ns ns ns ns ns ns
Must also meet parameter 47
N = prescale value (1, 2, 4, 8) N = prescale value (1, 2, 4, 8)
PIC16LCXX
Asynchronous Ft1 48
PIC16CXX PIC16LCXX
-- -- -- --
-- -- 200 7TOSC
ns ns kHz --
Timer1 oscillator input frequency range (oscillator enabled by setting bit T1OSCEN)
TCKEZtmr1 Delay from external clock edge to timer increment
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
2000 Microchip Technology Inc.
DS30605C-page 127
PIC16C63A/65B/73B/74B
FIGURE 16-10: CAPTURE/COMPARE/PWM TIMINGS (CCP1 AND CCP2)
CCPx (Capture mode)
50 52
51
CCPx (Compare or PWM mode) 53 Note: Refer to Figure 16-4 for load conditions. 54
TABLE 16-6:
Param Sym No. 50*
CAPTURE/COMPARE/PWM REQUIREMENTS (CCP1 AND CCP2)
Characteristic No Prescaler With Prescaler PIC16CXX PIC16LCXX Min 0.5TCY + 20 10 20 0.5TCY + 20 10 20 3TCY + 40 N -- -- -- -- Typ Max Units Conditions -- -- -- -- -- -- -- 10 25 10 25 -- -- -- -- -- -- -- 25 45 25 45 ns ns ns ns ns ns ns ns ns ns ns N = prescale value (1,4, or 16)
TccL CCP1 and CCP2 input low time TccH CCP1 and CCP2 input high time
51*
No Prescaler With Prescaler PIC16CXX PIC16LCXX
52* 53*
TccP CCP1 and CCP2 input period TccR CCP1 and CCP2 output rise time PIC16CXX PIC16LCXX
54*
TccF CCP1 and CCP2 output fall time PIC16CXX PIC16LCXX
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
DS30605C-page 128
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 16-11:
RE2/CS
PARALLEL SLAVE PORT TIMING (PIC16C65B/74B)
RE0/RD
RE1/WR
65 RD7:RD0 62 63 Note: Refer to Figure 16-4 for load conditions.
64
TABLE 16-7:
Param No.
62* 63*
PARALLEL SLAVE PORT REQUIREMENTS (PIC16C65B/74B)
Sym Characteristic Min 20 20 35 -- 10 Typ -- -- -- -- -- Max -- -- -- 80 30 Units ns ns ns ns ns Conditions
TdtV2wrH Data in valid before WR or CS (setup time) TwrH2dtI WR or CS to data in invalid (hold time) PIC16CXX PIC16LCXX
64 65*
TrdL2dtV RD and CS to data out valid TrdH2dtI RD or CS to data out invalid
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
2000 Microchip Technology Inc.
DS30605C-page 129
PIC16C63A/65B/73B/74B
FIGURE 16-12:
SS 70 SCK (CKP = 0) 71 72 78 SCK (CKP = 1) 79 78 79
EXAMPLE SPI MASTER MODE TIMING (CKE = 0)
80 SDO MSb 75, 76 SDI MSb IN 74 73 Note: Refer to Figure 16-4 for load conditions. BIT6 - - - -1
BIT6 - - - - - -1
LSb
LSb IN
TABLE 16-8:
Param No. 70 71 71A 72 72A 73 73A 74 75 76 78 79 80 TscL
EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0)
Characteristic SS to SCK or SCK input SCK input high time (Slave mode) SCK input low time (Slave mode) Continuous Single Byte Continuous Single Byte Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- -- PIC16CXX PIC16LCXX PIC16CXX -- -- -- -- Typ Max Units -- -- -- -- -- -- -- -- 10 20 10 10 20 10 -- -- -- -- -- -- -- -- -- 25 45 25 25 45 25 50 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns (Note 1) (Note 1) (Note 1) Conditions
Symbol TssL2scH, TssL2scL TscH
TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TscR TscF TscH2doV, TscL2doV
Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time PIC16CXX PIC16LCXX SDO data output fall time SCK output rise time (Master mode)
SCK output fall time (Master mode) SDO data output valid after SCK edge
-- -- 100 ns PIC16LCXX Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
DS30605C-page 130
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 16-13:
SS 81 SCK (CKP = 0) 71 73 SCK (CKP = 1) 80 78 72 79
EXAMPLE SPI MASTER MODE TIMING (CKE = 1)
SDO
MSb 75, 76
BIT6 - - - - - -1
LSb
SDI
MSb IN 74
BIT6 - - - -1
LSb IN
Note:
Refer to Figure 16-4 for load conditions.
TABLE 16-9:
Param No. 71 71A 72 72A 73 73A 74 75 76 78 79 80 81
EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1)
Characteristic SCK input high time (Slave mode) SCK input low time (Slave mode) Continuous Single Byte Continuous Single Byte Min 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- PIC16CXX PIC16LCXX -- -- TCY PIC16CXX PIC16LCXX -- Typ Max Units -- -- -- -- -- -- -- 10 20 10 10 20 10 -- -- -- -- -- -- -- -- -- -- 25 45 25 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns (Note 1) (Note 1) (Note 1) Conditions
Symbol TscH TscL TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TscR TscF TscH2doV, TscL2doV
Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time SDO data output fall time SCK output rise time (Master mode) PIC16CXX PIC16LCXX
SCK output fall time (Master mode) SDO data output valid after SCK edge
TdoV2scH, SDO data output setup to SCK edge TdoV2scL
Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
2000 Microchip Technology Inc.
DS30605C-page 131
PIC16C63A/65B/73B/74B
FIGURE 16-14:
SS 70 SCK (CKP = 0) 71 72 83
EXAMPLE SPI SLAVE MODE TIMING (CKE = 0)
78
79
SCK (CKP = 1) 79 78
80 SDO MSb 75, 76 SDI MSb IN 74 73 Note: Refer to Figure 16-4 for load conditions. BIT6 - - - -1
BIT6 - - - - - -1
LSb 77 LSb IN
TABLE 16-10: EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING (CKE = 0)
Param No. 70 71 71A 72 72A 73 73A 74 75 76 77 78 79 80 83 Symbol TssL2scH, TssL2scL TscH TscL TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TssH2doZ TscR TscF TscH2doV, TscL2doV TscH2ssH, TscL2ssH Characteristic SS to SCK or SCK input SCK input high time (Slave mode) Continuous Single Byte SCK input low time Continuous (Slave mode) Single Byte Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time PIC16CXX PIC16LCXX SDO data output fall time SS to SDO output hi-impedance SCK output rise time PIC16CXX (Master mode) PIC16LCXX SCK output fall time (Master mode) SDO data output valid PIC16CXX after SCK edge PIC16LCXX SS after SCK edge Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- 10 -- -- -- 1.5TCY + 40 Typ Max Units -- -- -- -- -- -- -- -- 10 20 10 -- 10 20 10 -- -- -- -- -- -- -- -- -- -- -- 25 45 25 50 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Conditions
(Note 1) (Note 1)
(Note 1)
Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
2000 Microchip Technology Inc.
DS30605C-page 132
PIC16C63A/65B/73B/74B
FIGURE 16-15:
SS
EXAMPLE SPI SLAVE MODE TIMING (CKE = 1)
82
SCK (CKP = 0)
70 83 71 72
SCK (CKP = 1) 80
SDO
MSb 75, 76
BIT6 - - - - - -1
LSb 77
SDI
MSb IN 74
BIT6 - - - -1
LSb IN
Note:
Refer to Figure 16-4 for load conditions.
TABLE 16-11: EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1)
Param No. 70 71 71A 72 72A 73A 74 75 76 77 78 79 80 82 83 Symbol TssL2scH, TssL2scL TscH TscL TB2B TscH2diL, TscL2diL TdoR TdoF TssH2doZ TscR TscF TscH2doV, TscL2doV TssL2doV TscH2ssH, TscL2ssH Characteristic SS to SCK or SCK input SCK input high time (Slave mode) SCK input low time (Slave mode) Continuous Single Byte Continuous Single Byte Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 1.5TCY + 40 100 -- -- 10 -- -- -- -- -- -- -- 1.5TCY + 40 Typ Max Units -- -- -- -- -- -- -- 10 20 10 -- 10 20 10 -- -- -- -- -- -- -- -- -- -- -- -- 25 45 25 50 25 45 25 50 100 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Conditions
(Note 1) (Note 1) (Note 1)
Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time SDO data output fall time SS to SDO output hi-impedance PIC16CXX SCK output rise time PIC16LCXX (Master mode) SCK output fall time (Master mode) PIC16CXX SDO data output valid PIC16LCXX after SCK edge PIC16CXX SDO data output valid PIC16LCXX after SS edge SS after SCK edge PIC16CXX PIC16LCXX
Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
2000 Microchip Technology Inc.
DS30605C-page 133
PIC16C63A/65B/73B/74B
FIGURE 16-16: I2C BUS START/STOP BITS TIMING
SCL 90 SDA
91 92
93
START Condition Note: Refer to Figure 16-4 for load conditions.
STOP Condition
TABLE 16-12: I2C BUS START/STOP BITS REQUIREMENTS
Param No. 90* 91* 92* 93 Sym Characteristic 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode Min Typ Max Units 4700 600 4000 600 4700 600 4000 600 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns Conditions Only relevant for Repeated START condition After this period the first clock pulse is generated
TSU:STA START condition Setup time THD:STA START condition Hold time TSU:STO STOP condition Setup time THD:STO STOP condition
Hold time 400 kHz mode * These parameters are characterized but not tested.
FIGURE 16-17:
I2C BUS DATA TIMING
103 100 101 102
SCL
90 91 106 107 92
SDA In
110 109 109
SDA Out Note: Refer to Figure 16-4 for load conditions.
DS30605C-page 134
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 16-13: I2C BUS DATA REQUIREMENTS
Param. No. 100* Sym THIGH Characteristic Clock high time 100 kHz mode 400 kHz mode SSP Module 101* TLOW Clock low time 100 kHz mode 400 kHz mode SSP Module 102* TR SDA and SCL rise time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Min 4.0 0.6 1.5TCY 4.7 1.3 1.5TCY -- 20 + 0.1Cb -- 20 + 0.1Cb 4.7 0.6 4.0 0.6 0 0 250 100 4.7 0.6 -- -- 4.7 1.3 -- Max -- -- -- -- -- -- 1000 300 300 300 -- -- -- -- -- 0.9 -- -- -- -- 3500 -- -- -- 400 ns ns ns ns s s s s ns s ns ns s s ns ns s s pF Time the bus must be free before a new transmission can start (Note 1) (Note 2) Cb is specified to be from 10-400 pF Only relevant for Repeated START condition After this period the first clock pulse is generated Cb is specified to be from 10-400 pF s s Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz Units s s Conditions Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz
103*
TF
SDA and SCL fall time
90*
TSU:STA
START condition setup time START condition hold time
91*
THD:STA
106*
THD:DAT
Data input hold time 100 kHz mode 400 kHz mode
107*
TSU:DAT
Data input setup time STOP condition setup time Output valid from clock Bus free time
100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode
92*
TSU:STO
109*
TAA
110*
TBUF
Cb
Bus capacitive loading
* These parameters are characterized but not tested. Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast mode (400 kHz) I2C bus device can be used in a standard mode (100 kHz) I2C bus system, but the requirement Tsu:DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard mode I2C bus specification) before the SCL line is released.
2000 Microchip Technology Inc.
DS30605C-page 135
PIC16C63A/65B/73B/74B
FIGURE 16-18: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
RC6/TX/CK pin RC7/RX/DT pin 120 Note:
121
121
122
Refer to Figure 16-4 for load conditions.
TABLE 16-14: USART SYNCHRONOUS TRANSMISSION REQUIREMENTS
Param No. 120* Sym TckH2dtV Characteristic SYNC XMIT (MASTER & SLAVE) Clock high to data out valid Clock out rise time and fall time (Master mode) PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX Min -- -- -- -- -- -- Typ -- -- -- -- -- -- Max 80 100 45 50 45 50 Units Conditions ns ns ns ns ns ns
121*
Tckrf
122*
Tdtrf
Data out rise time and fall time PIC16CXX PIC16LCXX
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
FIGURE 16-19:
USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
RC6/TX/CK pin RC7/RX/DT pin
125
126 Note: Refer to Figure 16-4 for load conditions.
TABLE 16-15: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Param No. 125* Sym TdtV2ckL Characteristic SYNC RCV (MASTER & SLAVE) Data setup before CK (DT setup time) Data hold after CK (DT hold time) Min Typ Max Units Conditions
15 15
-- --
-- --
ns ns
126*
TckL2dtl
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
DS30605C-page 136
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE 16-16: A/D CONVERTER CHARACTERISTICS: PIC16C73B/74B-04 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16C73B/74B-20 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16LC73B/74B-04 (COMMERCIAL, INDUSTRIAL)
Param Sym No. A01 NR Characteristic Resolution PIC16CXX PIC16LCXX A02 A03 A04 A05 A06 A10 A20 A25 A30 A40 EABS Total Absolute error EIL EDL EFS Integral linearity error Differential linearity error Full scale error Min -- -- -- -- -- -- -- -- 2.5V VSS - 0.3 -- -- -- 10 Typ -- -- -- -- -- -- -- guaranteed -- -- -- 180 90 -- Max 8 bits 8 bits <1 <1 <1 <1 <1 -- VDD + 0.3 VREF + 0.3 10.0 -- -- 1000 Units bit bit LSb LSb LSb LSb LSb -- V V k A A A Average current consumption when A/D is on (Note 1) During VAIN acquisition Based on differential of VHOLD to VAIN to charge CHOLD, see Section 12.1 During A/D Conversion cycle Conditions VREF = VDD = 5.12 V, VSS VAIN VREF VREF = VDD = 2.5 V VREF = VDD = 5.12 V, Vss VAIN VREF VREF = VDD = 5.12 V, Vss VAIN VREF VREF = VDD = 5.12 V, Vss VAIN VREF VREF = VDD = 5.12 V, Vss VAIN VREF VREF = VDD = 5.12 V, Vss VAIN VREF Vss VAIN VREF
EOFF Offset error -- Monotonicity (Note 3)
VREF Reference voltage VAIN Analog input voltage ZAIN Recommended impedance of analog voltage source IAD A/D conversion PIC16CXX current (VDD) PIC16LCXX
A50
IREF VREF input current (Note 2)
--
--
10
A
* These parameters are characterized but not tested. Data in "Typ" column is at 5 V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. 2: VREF current is from the RA3 pin or the VDD pin, whichever is selected as a reference input. 3: The A/D conversion result never decreases with an increase in the input voltage and has no missing codes.
2000 Microchip Technology Inc.
DS30605C-page 137
PIC16C63A/65B/73B/74B
FIGURE 16-20: A/D CONVERSION TIMING
1 TCY (TOSC/2)(1) 131 130 A/D CLK 132 BSF ADCON0, GO 134 Q4
A/D DATA
7
6
5
4
3
2
1
0
ADRES
OLD_DATA
NEW_DATA
ADIF GO SAMPLING STOPPED DONE
SAMPLE
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed.
TABLE 16-17: A/D CONVERSION REQUIREMENTS
Param Sym No. 130 TAD Characteristic A/D clock period PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX 131 132 TCNV Conversion time (not including S/H time) (Note 1) TACQ Acquisition time Min 1.6 2.0 2.0 3.0 11 5* Typ -- -- 4.0 6.0 -- -- Max -- -- 6.0 9.0 11 -- Units s s s s TAD s The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. Conditions TOSC based, VREF 3.0 V TOSC based, 2.5V VREF 5.5 V A/D RC mode A/D RC mode
134
TGO Q4 to A/D clock start
--
TOSC/2
--
--
135
TSWC Switching from convert sample time
1.5
--
--
TAD
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: ADRES register may be read on the following TCY cycle. 2: See Section 12.1 for minimum conditions.
DS30605C-page 138
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
17.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES
The data presented in this section is a statistical summary of data collected on units from different lots over a period of time. Note: Standard deviation is denoted by sigma (). * Typ or Typical represents the mean of the distribution at 25C. * Max or Maximum represents the mean + 3 over the temperature range of -40C to 85C. * Min or Minimum represents the mean - 3 over the temperature range of -40C to 85C.
The graphs and tables provided in this section are for design guidance and are not tested nor guaranteed. In some graphs or tables the data presented is outside specified operating range (e.g., outside specified VDD range). This is for information only and devices are ensured to operate properly only within the specified range.
2000 Microchip Technology Inc.
DS30605C-page 139
PIC16C63A/65B/73B/74B
FIGURE 17-1: TYPICAL IDD vs. FOSC OVER VDD - HS MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
7
6
5
IDD (mA)
4
5.5 V
3
5.0 V 4.5 V 4.0 V
2
3.5 V 3.0 V
1
2.5 V
0 4 6 8 10 12 FOSC (MHz) 14 16 18 20
FIGURE 17-2:
MAXIMUM IDD vs. FOSC OVER VDD - HS MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
7
6
5
5.5 V
IDD (mA)
4 5.0 V
4.5 V
3
4.0 V
2
3.5 V 3.0 V
1
2.5 V
0 4 6 8 10 12 FOSC (MHz) 14 16 18 20
DS30605C-page 140
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-3: TYPICAL IDD vs. FOSC OVER VDD - LP MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
100 90 80 70 60 IDD (A)
4.5 V
5.5 V
5.0 V
50
4.0 V
40
3.5 V
30
3.0 V
20 10 0 30 40 50
2.5 V
60 FOSC (kHz)
70
80
90
100
FIGURE 17-4:
MAXIMUM IDD vs. FOSC OVER VDD - LP MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
160
140
5.5 V
120
100 IDD (A)
5.0 V
80
4.5 V
60
4.0 V 3.5 V
40
3.0 V 2.5 V
20
0 30 40 50 60 FOSC (kHz) 70 80 90 100
2000 Microchip Technology Inc.
DS30605C-page 141
PIC16C63A/65B/73B/74B
FIGURE 17-5: TYPICAL IDD vs. FOSC OVER VDD - XT MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
1.4
1.2 5.5 V 1.0
5.0 V
IDD (mA)
0.8
4.5 V
0.6
4.0 V 3.5 V
0.4
3.0 V 2.5 V
0.2
0.0 0.0 0.5 1.0 1.5 2.0 FOSC (MHz) 2.5 3.0 3.5 4.0
FIGURE 17-6:
MAXIMUM IDD vs. FOSC OVER VDD - XT MODE
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
1.8 1.6
5.5 V
1.4
5.0 V
1.2
4.5 V
IDD (mA)
1.0
4.0 V
0.8
3.5 V
0.6 0.4 0.2 0.0 0.0 0.5 1.0 1.5 2.0 FOSC (MHz) 2.5 3.0 3.5 4.0
3.0 V 2.5 V
DS30605C-page 142
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-7: AVERAGE FOSC vs. VDD FOR VARIOUS RESISTANCES - RC MODE; C = 20 PF
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
4.5
Not recommended for operation over 4 MHz
4.0 3.5 3.0 FOSC (MHz) 2.5 2.0 1.5 1.0 0.5
100 k 5.1 k
3.3 k
10 k
0.0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
FIGURE 17-8:
AVERAGE FOSC vs. VDD FOR VARIOUS RESISTANCES - RC MODE; C = 100 PF
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
2.5
2.0
3.3 k
FOSC (MHz)
1.5
5.1 k
1.0
10 k
0.5
100 k
0.0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
2000 Microchip Technology Inc.
DS30605C-page 143
PIC16C63A/65B/73B/74B
FIGURE 17-9: AVERAGE FOSC vs. VDD FOR VARIOUS RESISTANCES - RC MODE; C = 300 PF
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
1,000 900 800 700
3.3 k
FOSC (kHz)
600 500
5.1 k
400 300
10 k
200 100
100 k
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
FIGURE 17-10:
VTH vs. VDD OVER TEMPERATURE - TTL INPUT
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
2.0 1.8 1.6 1.4 Max (-40C) 1.2 VTH (V)
Typ (25C)
1.0
Min (125C)
0.8 0.6 0.4 0.2 0.0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
DS30605C-page 144
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-11: VIL, VIH vs. VDD OVER TEMPERATURE - SCHMITT TRIGGER INPUT (I2C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
4.0
3.5 VIH Max (125C) 3.0 VIH Min (-40C) 2.5 VIN (V) VIH Typ (25C)
2.0
VIL Max (125C)
1.5 VIL Typ (25C) 1.0 VIL Min (-40C)
0.5
0.0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
FIGURE 17-12:
VIL, VIH vs. VDD OVER TEMPERATURE - SCHMITT TRIGGER INPUT
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
4.0
3.5 VIH Max (125C) 3.0 VIH Typ (25C) 2.5 VIH Min (-40C) VIN (V) VIL Max (125C) 2.0 VIL Typ (25C) 1.5 VIL Min (-40C)
1.0
0.5
0.0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
2000 Microchip Technology Inc.
DS30605C-page 145
PIC16C63A/65B/73B/74B
FIGURE 17-13: VOH vs. IOH AT VDD = 3.0 V
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
3.5
3.0
2.5
Max (-40C)
VOH (V)
2.0 Typical (25C) 1.5
1.0
Min (125C)
0.5
0.0 0 5 10 IOH (mA) 15 20 25
FIGURE 17-14:
VOH vs. IOH AT VDD = 5.0 V
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
5.5 5.0 4.5
Max (-40C)
4.0
Typical (25C)
3.5 VOH (V) 3.0 2.5
Min (125C)
2.0 1.5 1.0 0.5 0.0 0 5 10 IOH (mA) 15 20 25
DS30605C-page 146
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-15: VOL vs. IOL AT VDD = 3.0 V
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
2.4 2.2 2.0 1.8 1.6 1.4 VOL (V) 1.2 1.0
Typ (25C)
Max (125C)
0.8 0.6 0.4
Min (-40C)
0.2 0.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 IOL (-mA)
FIGURE 17-16:
VOL vs. IOL AT VDD = 5.0 V
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
2.0 1.8 1.6 1.4 1.2 VOL (V)
Max (125C)
1.0 0.8
Typ (25C)
0.6 0.4
Min (-40C)
0.2 0.0 0 2 4 6 8 10 12 14 16 18 20 22 24 26 IOL (-mA)
2000 Microchip Technology Inc.
DS30605C-page 147
PIC16C63A/65B/73B/74B
FIGURE 17-17: IPD vs. VDD (85C) - SLEEP MODE, ALL PERIPHERALS DISABLED
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
140 Max 85C 120
100
IPD (nA)
80
60
Typ 85C
40
20
Max 25C Max -40C
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
FIGURE 17-18:
IPD vs. VDD (125C) - SLEEP MODE, ALL PERIPHERALS DISABLED
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
1,400
1,200
Max (125C)
1,000
IPD (nA)
800
600
Typ (125C)
400
200
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
DS30605C-page 148
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-19: IBOR vs. VDD OVER TEMPERATURE (-40C TO +125C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
200 180 160 140
Max (125C)
IBOR (uA)
120 100
Typ (25C) Device in SLEEP Max (125C) Typ (25C)
80 60 40 20 0 2.5 3.0
Device in RESET
Indeterminant State
RESET current depends on oscillator mode, frequency, and circuit.
3.5
4.0 VDD (V)
4.5
5.0
5.5
FIGURE 17-20:
ITIMER1 vs. VDD (-10C TO +70C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
120
100
Max (-10C to 70C)
80 ITIMER1 (uA)
60 Typical (25C)
40
20
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
2000 Microchip Technology Inc.
DS30605C-page 149
PIC16C63A/65B/73B/74B
FIGURE 17-21: IWDT vs. VDD (-40C TO +125C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
20 18 16 14 12
Max (-40C to 125C)
IWDT (A)
10 8 Typical (25C) 6 4 2 0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
FIGURE 17-22:
WDT PERIOD vs. VDD OVER TEMPERATURE (-40C TO +125C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
40
35
Maximum (125C)
30
WDT Period (ms)
25
20
Typical (25C)
15
10
Minimum (-40C)
5
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
DS30605C-page 150
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
FIGURE 17-23: AVERAGE WDT PERIOD vs. VDD OVER TEMPERATURE (-40C TO +125C)
Typical: statistical mean @ 25C Maximum: mean + 3 (-40C to 125C) Minimum: mean - 3 (-40C to 125C)
40
35
30
125C 85C
WDT Period (ms)
25
20
25C
15
-40C
10
5
0 2.5 3.0 3.5 4.0 VDD (V) 4.5 5.0 5.5
2000 Microchip Technology Inc.
DS30605C-page 151
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 152
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.0
18.1
PACKAGING INFORMATION
Package Marking Information
28-Lead PDIP (Skinny DIP) XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN Example PIC16C73B-04/SP 0017HAT
28-Lead CERDIP Windowed XXXXXXXXXXXXXX XXXXXXXXXXXXXX YYWWNNN
Example PIC16C73B/JW 0017CAT
28-Lead SOIC XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX YYWWNNN
Example PIC16C73B-20/SO 0017SAA
28-Lead SSOP XXXXXXXXXXXX XXXXXXXXXXXX YYWWNNN
Example PIC16C73B20I/SS025 0017SBP
Legend:
XX...X YY WW NNN
Customer specific information* Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code
Note:
In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week code, facility code, mask rev#, and assembly code. For OTP marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price.
2000 Microchip Technology Inc.
DS30605C-page 153
PIC16C63A/65B/73B/74B
Package Marking Information (Cont'd)
40-Lead PDIP XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXX YYWWNNN
Example PIC16C74B-04/P 0017SAA
40-Lead CERDIP Windowed XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX YYWWNNN
Example PIC16C74B/JW 0017HAT
44-Lead TQFP
Example
XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN
PIC16C74B -20/PT 0017HAT
44-Lead MQFP
Example
XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN
PIC16C74B -20/PQ 0017SAT
44-Lead PLCC
Example
XXXXXXXXXX XXXXXXXXXX XXXXXXXXXX YYWWNNN
PIC16C74B -20/L 0017SAT
DS30605C-page 154
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.2 28-Lead Skinny Plastic Dual In-line (SP) - 300 mil (PDIP)
E1
D
2 n 1
E
A2 A L A1 B1 B p
c eB
Units Number of Pins Pitch Top to Seating Plane Molded Package Thickness Base to Seating Plane Shoulder to Shoulder Width Molded Package Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Mold Draft Angle Top Mold Draft Angle Bottom Dimension Limits n p A A2 A1 E E1 D L c B1 B eB MIN
INCHES* NOM 28 .100 .140 .125 .015 .300 .275 1.345 .125 .008 .040 .016 .320 5 5 .310 .285 1.365 .130 .012 .053 .019 .350 10 10 .325 .295 1.385 .135 .015 .065 .022 .430 15 15 .150 .130 .160 .135 MAX MIN
MILLIMETERS NOM 28 2.54 3.56 3.18 0.38 7.62 6.99 34.16 3.18 0.20 1.02 0.41 8.13 5 5 7.87 7.24 34.67 3.30 0.29 1.33 0.48 8.89 10 10 8.26 7.49 35.18 3.43 0.38 1.65 0.56 10.92 15 15 3.81 3.30 4.06 3.43 MAX
* Controlling Parameter Significant Characteristic Notes: Dimension D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-095 Drawing No. C04-070
2000 Microchip Technology Inc.
DS30605C-page 155
PIC16C63A/65B/73B/74B
18.3 28-Lead Ceramic Dual In-line with Window (JW) - 300 mil (CERDIP)
E1
W2
D
2 n W1 E A c A1 Units Dimension Limits n p A A2 A1 E E1 D L c B1 B eB W1 W2 INCHES* NOM 28 .100 .183 .160 .023 .313 .290 1.458 .140 .010 .058 .019 .385 .140 .300 B1 B MIN MAX MIN A2 L eB 1
p MILLIMETERS NOM 28 2.54 4.32 4.64 3.94 4.06 0.38 0.57 7.62 7.94 7.24 7.37 36.32 37.02 3.43 3.56 0.20 0.25 1.27 1.46 0.41 0.47 8.76 9.78 3.30 3.56 7.37 7.62
MAX
Number of Pins Pitch Top to Seating Plane Ceramic Package Height Standoff Shoulder to Shoulder Width Ceramic Pkg. Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Window Width Window Length * Controlling Parameter Significant Characteristic JEDEC Equivalent: MO-058 Drawing No. C04-080
.170 .155 .015 .300 .285 1.430 .135 .008 .050 .016 .345 .130 .290
.195 .165 .030 .325 .295 1.485 .145 .012 .065 .021 .425 .150 .310
4.95 4.19 0.76 8.26 7.49 37.72 3.68 0.30 1.65 0.53 10.80 3.81 7.87
DS30605C-page 156
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.4 28-Lead Plastic Small Outline (SO) - Wide, 300 mil (SOIC)
E E1 p
D
B n h 45 c A Units Dimension Limits n p A A2 A1 E E1 D h L c B L A1 INCHES* NOM 28 .050 .099 .091 .008 .407 .295 .704 .020 .033 4 .011 .017 12 12 MILLIMETERS NOM 28 1.27 2.36 2.50 2.24 2.31 0.10 0.20 10.01 10.34 7.32 7.49 17.65 17.87 0.25 0.50 0.41 0.84 0 4 0.23 0.28 0.36 0.42 0 12 0 12 A2 2 1
MIN
MAX
MIN
MAX
Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Top Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic
.093 .088 .004 .394 .288 .695 .010 .016 0 .009 .014 0 0
.104 .094 .012 .420 .299 .712 .029 .050 8 .013 .020 15 15
2.64 2.39 0.30 10.67 7.59 18.08 0.74 1.27 8 0.33 0.51 15 15
Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-013 Drawing No. C04-052
2000 Microchip Technology Inc.
DS30605C-page 157
PIC16C63A/65B/73B/74B
18.5 28-Lead Plastic Shrink Small Outline (SS) - 209 mil, 5.30 mm (SSOP)
E E1 p
D
B n 2 1
A c A2
L
A1
Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width Overall Length Foot Length Lead Thickness Foot Angle Lead Width Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic
Units Dimension Limits n p A A2 A1 E E1 D L c B
MIN
.068 .064 .002 .299 .201 .396 .022 .004 0 .010 0 0
INCHES NOM 28 .026 .073 .068 .006 .309 .207 .402 .030 .007 4 .013 5 5
MAX
MIN
.078 .072 .010 .319 .212 .407 .037 .010 8 .015 10 10
MILLIMETERS* NOM MAX 28 0.65 1.73 1.85 1.98 1.63 1.73 1.83 0.05 0.15 0.25 7.59 7.85 8.10 5.11 5.25 5.38 10.06 10.20 10.34 0.56 0.75 0.94 0.10 0.18 0.25 0.00 101.60 203.20 0.25 0.32 0.38 0 5 10 0 5 10
Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-150 Drawing No. C04-073
DS30605C-page 158
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.6 40-Lead Plastic Dual In-line (P) - 600 mil (PDIP)
E1
D
n E
2 1
A c eB Units Dimension Limits n p INCHES* NOM 40 .100 .175 .150 A1 B1 B p MILLIMETERS NOM 40 2.54 4.06 4.45 3.56 3.81 0.38 15.11 15.24 13.46 13.84 51.94 52.26 3.05 3.30 0.20 0.29 0.76 1.27 0.36 0.46 15.75 16.51 5 10 5 10
A2 L
MIN
MAX
MIN
MAX
Number of Pins Pitch Top to Seating Plane A .160 .190 Molded Package Thickness A2 .140 .160 Base to Seating Plane .015 A1 Shoulder to Shoulder Width E .595 .600 .625 Molded Package Width E1 .530 .545 .560 Overall Length D 2.045 2.058 2.065 Tip to Seating Plane L .120 .130 .135 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .030 .050 .070 Lower Lead Width B .014 .018 .022 Overall Row Spacing eB .620 .650 .680 Mold Draft Angle Top 5 10 15 Mold Draft Angle Bottom 5 10 15 * Controlling Parameter Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-011 Drawing No. C04-016
4.83 4.06 15.88 14.22 52.45 3.43 0.38 1.78 0.56 17.27 15 15
2000 Microchip Technology Inc.
DS30605C-page 159
PIC16C63A/65B/73B/74B
18.7 40-Lead Ceramic Dual In-line with Window (JW) - 600 mil (CERDIP)
D
n E
2 1
A2 c eB Units Dimension Limits n p A A2 A1 E E1 D L c B B1 eB W INCHES* NOM 40 .100 .205 .160 .045 .600 .520 2.050 .140 .011 .053 .020 .660 .350 B1 B p MILLIMETERS NOM 40 2.54 4.70 5.21 3.94 4.06 0.76 1.14 15.11 15.24 13.06 13.21 51.82 52.07 3.43 3.56 0.20 0.28 1.27 1.33 0.41 0.51 15.49 16.76 8.64 8.89 L
MIN
MAX
MIN
MAX
Number of Pins Pitch Top to Seating Plane Ceramic Package Height Standoff Shoulder to Shoulder Width Ceramic Pkg. Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Window Diameter * Controlling Parameter Significant Characteristic JEDEC Equivalent: MO-103 Drawing No. C04-014
.185 .155 .030 .595 .514 2.040 .135 .008 .050 .016 .610 .340
.225 .165 .060 .625 .526 2.060 .145 .014 .055 .023 .710 .360
5.72 4.19 1.52 15.88 13.36 52.32 3.68 0.36 1.40 0.58 18.03 9.14
DS30605C-page 160
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.8 44-Lead Plastic Thin Quad Flatpack (PT) 10x10x1 mm Body, 1.0/0.10 mm Lead Form (TQFP)
E E1 #leads=n1 p
D1
D
B n
2 1
CH x 45 A
c
L A1 (F) Units Dimension Limits n p n1 A A2 A1 L (F) E D E1 D1 c B CH INCHES NOM 44 .031 11 .043 .039 .004 .024 .039 3.5 .472 .472 .394 .394 .006 .015 .035 10 10 MILLIMETERS* NOM 44 0.80 11 1.00 1.10 0.95 1.00 0.05 0.10 0.45 0.60 1.00 0 3.5 11.75 12.00 11.75 12.00 9.90 10.00 9.90 10.00 0.09 0.15 0.30 0.38 0.64 0.89 5 10 5 10 A2
MIN
MAX
MIN
MAX
Number of Pins Pitch Pins per Side Overall Height Molded Package Thickness Standoff Foot Length Footprint (Reference) Foot Angle Overall Width Overall Length Molded Package Width Molded Package Length Lead Thickness Lead Width Pin 1 Corner Chamfer Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic
.039 .037 .002 .018 0 .463 .463 .390 .390 .004 .012 .025 5 5
.047 .041 .006 .030 7 .482 .482 .398 .398 .008 .017 .045 15 15
1.20 1.05 0.15 0.75 7 12.25 12.25 10.10 10.10 0.20 0.44 1.14 15 15
Notes: Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-026 Drawing No. C04-076
2000 Microchip Technology Inc.
DS30605C-page 161
PIC16C63A/65B/73B/74B
18.9 44-Lead Plastic Metric Quad Flatpack (PQ) 10x10x2 mm Body, 1.6/0.15 mm Lead Form (MQFP)
E E1 #leads=n1 p
D1 D
B n
2 1
CH x 45
A1
c
A
L
(F)
A2
Number of Pins Pitch Pins per Side Overall Height Molded Package Thickness Standoff Foot Length Footprint (Reference) Foot Angle Overall Width Overall Length Molded Package Width Molded Package Length Lead Thickness Lead Width Pin 1 Corner Chamfer Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter Significant Characteristic
Units Dimension Limits n p n1 A A2 A1 L (F) E D E1 D1 c B CH
MIN
.079 .077 .002 .029 0 .510 .510 .390 .390 .005 .012 .025 5 5
INCHES NOM 44 .031 11 .086 .080 .006 .035 .063 3.5 .520 .520 .394 .394 .007 .015 .035 10 10
MAX
MIN
.093 .083 .010 .041 7 .530 .530 .398 .398 .009 .018 .045 15 15
MILLIMETERS* NOM 44 0.80 11 2.00 2.18 1.95 2.03 0.05 0.15 0.73 0.88 1.60 0 3.5 12.95 13.20 12.95 13.20 9.90 10.00 9.90 10.00 0.13 0.18 0.30 0.38 0.64 0.89 5 10 5 10
MAX
2.35 2.10 0.25 1.03 7 13.45 13.45 10.10 10.10 0.23 0.45 1.14 15 15
Notes: Dimensions D1 and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-022 Drawing No. C04-071
DS30605C-page 162
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
18.10 44-Lead Plastic Leaded Chip Carrier (L) - Square (PLCC)
E E1 #leads=n1
D1 D
n12 CH2 x 45 CH1 x 45 A3 A2
35
A B1 B p D2
c E2 Units Dimension Limits n p INCHES* MIN NOM 44 .050 11 .165 .173 .145 .153 .028 .020 .024 .029 .040 .045 .000 .005 .685 .690 .685 .690 .650 .653 .650 .653 .590 .620 .590 .620 .008 .011 .026 .029 .013 .020 0 5 0 5
A1
MAX
MIN
Number of Pins Pitch Pins per Side n1 Overall Height A .180 .160 Molded Package Thickness A2 .035 Standoff A1 A3 Side 1 Chamfer Height .034 Corner Chamfer 1 CH1 .050 Corner Chamfer (others) CH2 .010 Overall Width E .695 Overall Length D .695 Molded Package Width E1 .656 Molded Package Length D1 .656 Footprint Width E2 .630 Footprint Length .630 D2 c Lead Thickness .013 Upper Lead Width B1 .032 Lower Lead Width B .021 Mold Draft Angle Top 10 Mold Draft Angle Bottom 10 * Controlling Parameter Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-047 Drawing No. C04-048
MILLIMETERS NOM 44 1.27 11 4.19 4.39 3.68 3.87 0.71 0.51 0.61 0.74 1.02 1.14 0.00 0.13 17.40 17.53 17.40 17.53 16.51 16.59 16.51 16.59 14.99 15.75 14.99 15.75 0.20 0.27 0.66 0.74 0.33 0.51 0 5 0 5
MAX
4.57 4.06 0.89 0.86 1.27 0.25 17.65 17.65 16.66 16.66 16.00 16.00 0.33 0.81 0.53 10 10
2000 Microchip Technology Inc.
DS30605C-page 163
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 164
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
APPENDIX A:
Version A
REVISION HISTORY
Date 7/98 Revision Description This is a new data sheet. However, the devices described in this data sheet are the upgrades to the devices found in the PIC16C6X Data Sheet, DS30234, and the PIC16C7X Data Sheet, DS30390. Corrections to Version A data sheet for technical accuracy. Added data: * Operation of the SMP and CKE bits of the SSPSTAT register in I2C mode have been specified * Frequency vs. VDD graphs for device operating area (in Electrical Specifications) * Formula for calculating A/D acquisition time, TACQ (in the A/D section) * Brief description of instructions Removed data (see PICmicroTM Mid-Range MCU Family Reference Manual, DS33023, for additional data): * USART Baud Rate Tables (formulas for calculating baud rate remain) * Minor changes to text to clarify content * Revised some DC specifications * Included characteristic charts and graphs
B
1/99
C
12/00
APPENDIX B:
TABLE B-1:
Difference A/D Parallel Slave Port Packages
DEVICE DIFFERENCES
The differences between the devices in this data sheet are listed in Table B-1.
DEVICE DIFFERENCES
PIC16C63A no no 28-pin PDIP, 28-pin windowed CERDIP, 28-pin SOIC, 28-pin SSOP no yes 40-pin PDIP, 40-pin windowed CERDIP, 44-pin TQFP, 44-pin MQFP, 44-pin PLCC PIC16C65B PIC16C73B 5 channels, 8 bits no 28-pin PDIP, 28-pin windowed CERDIP, 28-pin SOIC, 28-pin SSOP PIC16C74B 8 channels, 8 bits yes 40-pin PDIP, 40-pin windowed CERDIP, 44-pin TQFP, 44-pin MQFP, 44-pin PLCC
2000 Microchip Technology Inc.
DS30605C-page 165
PIC16C63A/65B/73B/74B
APPENDIX C: DEVICE MIGRATIONS PIC16C63/65A/73A/74A PIC16C63A/65B/73B/74B
This document is intended to describe the functional differences and the electrical specification differences that are present when migrating from one device to the next. Table C-1 shows functional differences, while Table C-2 shows electrical and timing differences. Note: Even though compatible devices are specified to be tested to the same electrical specification, the device characteristics may be different from each other (due to process differences). For systems that were designed to the device specifications, these process differences should not cause any issues in the application. For systems that did not tightly meet the electrical specifications, the process differences may cause the device to behave differently in the application.
Note:
While there are no functional or electrical changes to the device oscillator specifications, the user should verify that the device oscillator starts and performs as expected. Adjusting the loading capacitor values and/or the oscillator mode may be required.
TABLE C-1:
No. 1 2 3 4 5 6 7 SSP Timers Module CCP
FUNCTIONAL DIFFERENCES
Differences from PIC16C63/65A/73A/74A CCP Special Event Trigger clears Timer1. Compare mode drives pin correctly. Writing to TMR1L does not affect TMR1H. WDT/TMR0 prescaler assignment changes do not affect TMR0 count. TMR2 SPI clock synchronized to start of SPI Transmission. Can now transmit multiple words in SPI mode. Supports all four SPI modes. (Now uses SSP vs. BSSP module.) See SSP module in the PICmicroTM Mid-Range MCU Family Reference Manual (DS33023). I2C no longer generates ACK pulses when module is enabled. H/W S/W Prog. -- -- -- -- -- -- -- -- -- -- -- -- -- --
8 9 10
-- -- --

-- -- --
USART Async receive errors due to BRGH setting corrected. A/D
VREF = VDD when all inputs are configured as digital. This allows conversion of digital inputs. (A/D on PIC16C73X/74X only.) H/W - Issues may exist with regard to the application circuits. S/W - Issues may exist with regard to the user program. Prog. - Issues may exist when writing the program to the controller.
DS30605C-page 166
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TABLE C-2:
Param No.
Core D001 D001A D005 D150* VDD BVDD VOD Supply Voltage Brown-out Reset Voltage Open-Drain High Voltage on RA4 Reference voltage Conversion time (Note 2) (not including S/H time) 4.0 -- 3.7 -- -- -- 4.0 -- 6.0 -- 4.3 14.0 4.0 VBOR(1) 3.65 -- -- -- -- 5.5 5.5 4.35 8.5 V V V V
SPECIFICATION DIFFERENCES
PIC16C63/65A/73A/74A PIC16C63A/65B/73B/74B Unit Min Typ Max Min Typ Max Characteristic
Symbol
A/D Converter A20 VREF 131 TCNV SSP in SPI mode 71 TscH 71A 72 TscL 72A 73 TdiV2scH TdiV2scL TB2B
3.0 --
-- VDD + 0.3 9.5 -- (Note 3) -- -- -- --
2.5 11 (Note 4) 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- -- -- -- --
-- --
VDD + 0.3 V 11 TAD (Note 4) -- -- -- -- -- -- -- 25 45 25 45 50 100 ns ns ns ns ns ns ns ns ns ns ns ns ns
73A (Note 5) 74 TscH2diL TscL2diL 75 TdoR 78 TscR
80
TscH2doV TscL2doV
83
-- 50 1.5TCY + 40 -- -- ns TscH2ssH TscL2ssH Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. When BOR is enabled, the device will operate until VDD drops below VBOR. ADRES register may be read on the following TCY cycle. This is the time that the actual conversion requires. This is the time from when the GO/DONE bit is set, to when the conversion result appears in ADRES. Specification 73A is only required if specifications 71A and 72A are used.
SCK input high Continuous TCY+20 time (Slave mode) Single Byte SCK input low Continuous TCY+20 time Single Byte (Slave mode) Setup time of SDI data input to 50 SCK edge Last clock edge of Byte1 to the -- 1st clock edge of Byte2 Hold time of SDI data input to 50 SCK edge SDO data output PIC16CXX -- rise time PIC16LCXX SCK output rise PIC16CXX -- time (Master PIC16LCXX mode) SDO data output PIC16CXX -- valid after SCK PIC16LCXX edge -- SS after SCK edge
-- -- -- -- -- -- -- 10 20 10 20 -- --
-- -- -- 10 10
-- -- -- 25 25
--
50
Note 1: 2: 3: 4: 5:
2000 Microchip Technology Inc.
DS30605C-page 167
PIC16C63A/65B/73B/74B
APPENDIX D: MIGRATION FROM BASELINE TO MID-RANGE DEVICES
To convert code written for PIC16C5X to PIC16CXX, the user should take the following steps: 1. 2. Remove any program memory page select operations (PA2, PA1, PA0 bits) for CALL, GOTO. Revisit any computed jump operations (write to PC or add to PC, etc.) to make sure page bits are set properly under the new scheme. Eliminate any data memory page switching. Redefine data variables to reallocate them. Verify all writes to STATUS, OPTION and FSR registers since these have changed. Change RESET vector to 0000h. This section discusses how to migrate from a baseline device (i.e., PIC16C5X) to a mid-range device (i.e., PIC16CXXX). The following are the list of modifications over the PIC16C5X microcontroller family: 1. Instruction word length is increased to 14-bits. This allows larger page sizes, both in program memory (2 K now as opposed to 512 before) and register file (128 bytes now versus 32 bytes before). A PC high latch register (PCLATH) is added to handle program memory paging. Bits PA2, PA1 and PA0 are removed from STATUS register. Data memory paging is redefined slightly. STATUS register is modified. Four new instructions have been added: RETURN, RETFIE, ADDLW and SUBLW. Two instructions, TRIS and OPTION, are being phased out, although they are kept for compatibility with PIC16C5X. OPTION and TRIS registers are made addressable. Interrupt capability is added. Interrupt vector is at 0004h. Stack size is increased to 8-deep. RESET vector is changed to 0000h. RESET of all registers is revisited. Five different RESET (and wake-up) types are recognized. Registers are reset differently. Wake up from SLEEP through interrupt is added. Two separate timers, Oscillator Start-up Timer (OST) and Power-up Timer (PWRT) are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. PORTB has weak pull-ups and interrupt-on-change feature. T0CKI pin is also a port pin (RA4) now. FSR is made a full 8-bit register. "In-Circuit Serial Programming" (ICSP) is made possible. The user can program PIC16CXX devices using only five pins: VDD, VSS, MCLR/VPP, RB6 (clock) and RB7 (data in/out). PCON status register is added with a Power-on Reset status bit (POR). Code protection scheme is enhanced, such that portions of the program memory can be protected, while the remainder is unprotected. Brown-out protection circuitry has been added. Controlled by configuration word bit BODEN. Brown-out Reset ensures the device is placed in a RESET condition if VDD dips below a fixed setpoint.
3. 4. 5.
2.
3. 4.
5. 6. 7. 8. 9.
10. 11.
12. 13. 14. 15.
16. 17.
18.
DS30605C-page 168
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
INDEX A
A/D ADCON0 Register....................................................... 79 ADCON1 Register....................................................... 80 Analog Input Model Block Diagram............................. 82 Analog-to-Digital Converter......................................... 79 Block Diagram............................................................. 81 Configuring Analog Port Pins...................................... 83 Configuring the Interrupt ............................................. 81 Configuring the Module............................................... 81 Conversion Clock........................................................ 83 Conversions ................................................................ 83 Converter Characteristics ......................................... 137 Effects of a RESET ..................................................... 83 Faster Conversion - Lower Resolution Trade-off ........ 83 Internal Sampling Switch (Rss) Impedance ................ 82 Operation During SLEEP ............................................ 83 Sampling Requirements.............................................. 82 Source Impedance...................................................... 82 Timing Diagram......................................................... 138 Using the CCP Trigger ................................................ 83 Absolute Maximum Ratings .............................................. 113 ACK............................................................................... 60, 62 ADRES Register ........................................................... 17, 79 Application Notes AN552 (Implementing Wake-up on Key Strokes Using PIC16CXXX)..................................................... 31 AN556 (Table Reading Using PIC16CXX) .................. 26 AN578 (Use of the SSP Module in the I2C Multi-Master Environment).......................................... 55 AN607, (Power-up Trouble Shooting) ......................... 89 Architecture Overview ....................................................................... 9 Assembler MPASM(R) Assembler ................................................. 107 BOR bit ......................................................................... 25, 89 BRGH bit ............................................................................ 67 Brown-out Reset (BOR) Timing Diagram ........................................................ 126 Buffer Full Status bit, BF..................................................... 56
C
C bit .................................................................................... 19 Capture/Compare/PWM Capture Block Diagram .................................................... 51 CCP1CON Register............................................ 50 CCP1IF............................................................... 51 Mode .................................................................. 51 Prescaler ............................................................ 51 CCP Timer Resources................................................ 49 Compare Block Diagram .................................................... 52 Mode .................................................................. 52 Software Interrupt Mode ..................................... 52 Special Event Trigger ......................................... 52 Special Trigger Output of CCP1 ......................... 52 Special Trigger Output of CCP2 ......................... 52 Interaction of Two CCP Modules ................................ 49 Section........................................................................ 49 Special Event Trigger and A/D Conversions............... 52 Capture/Compare/PWM (CCP) PWM Block Diagram .................................................. 52 PWM Mode................................................................. 52 PWM, Example Frequencies/Resolutions .................. 53 Timing Diagram ........................................................ 128 CCP2IE bit .......................................................................... 24 CCP2IF bit .......................................................................... 24 CCPR1H Register......................................................... 17, 49 CCPR1L Register ............................................................... 49 CCPR2H Register............................................................... 17 CCPR2L Register ............................................................... 17 CCPxM0 bit......................................................................... 50 CCPxM1 bit......................................................................... 50 CCPxM2 bit......................................................................... 50 CCPxM3 bit......................................................................... 50 CCPxX bit ........................................................................... 50 CCPxY bit ........................................................................... 50 CKE .................................................................................... 56 CKP .................................................................................... 57 Clock Polarity Select bit, CKP............................................. 57 Clocking Scheme................................................................ 14 Code Examples Call of a Subroutine in Page 1 from Page 0 ............... 26 Indirect Addressing..................................................... 27 Initializing PORTA....................................................... 29 Code Protection ............................................................ 85, 98 Computed GOTO................................................................ 26 Configuration Bits ............................................................... 85 CREN bit............................................................................. 66 CS pin................................................................................. 37
B
Baud Rate Formula ............................................................. 67 BF ................................................................................. 56, 60 Block Diagrams A/D .............................................................................. 81 Analog Input Model ..................................................... 82 Capture ....................................................................... 51 Compare ..................................................................... 52 I2C Mode..................................................................... 60 On-Chip Reset Circuit ................................................. 88 PIC16C74 ................................................................... 10 PIC16C74A ................................................................. 10 PIC16C77 ................................................................... 10 PORTC ....................................................................... 33 PORTD (In I/O Port Mode).......................................... 34 PORTD and PORTE as a Parallel Slave Port............. 37 PORTE (In I/O Port Mode).......................................... 35 PWM ........................................................................... 52 RA4/T0CKI Pin............................................................ 29 RB3:RB0 Port Pins ..................................................... 31 RB7:RB4 Port Pins ..................................................... 31 SSP in I2C Mode......................................................... 60 SSP in SPI Mode ........................................................ 55 Timer0/WDT Prescaler................................................ 39 Timer2 ......................................................................... 47 USART Receive.......................................................... 70 USART Transmit ......................................................... 68 Watchdog Timer .......................................................... 96
2000 Microchip Technology Inc.
DS30605C-page 169
PIC16C63A/65B/73B/74B
D
D/A ...................................................................................... 56 Data Memory Register File Map ........................................................ 16 Data/Address bit, D/A.......................................................... 56 DC bit .................................................................................. 19 Development Support ........................................................... 5 Device Differences ............................................................ 165 Direct Addressing................................................................ 27 COMF ....................................................................... 103 DECF ........................................................................ 103 DECFSZ ................................................................... 103 GOTO ....................................................................... 103 INCF ......................................................................... 103 INCFSZ..................................................................... 103 IORLW ...................................................................... 104 IORWF...................................................................... 104 MOVF ....................................................................... 104 MOVLW .................................................................... 104 MOVWF .................................................................... 104 NOP .......................................................................... 104 RETFIE ..................................................................... 105 RETLW ..................................................................... 105 RETURN................................................................... 105 RLF ........................................................................... 105 RRF .......................................................................... 105 SLEEP ...................................................................... 105 SUBLW ..................................................................... 106 SUBWF..................................................................... 106 SWAPF ..................................................................... 106 XORLW..................................................................... 106 XORWF .................................................................... 106 Section........................................................................ 99 Summary Table......................................................... 100 INT Interrupt........................................................................ 94 INTCON Register................................................................ 21 INTEDG bit ................................................................... 20, 94 Internal Sampling Switch (Rss) Impedance........................ 82 Interrupts............................................................................. 85 PORTB Change.......................................................... 94 RB7:RB4 Port Change................................................ 31 Section........................................................................ 93 TMR0 .......................................................................... 94 IRP bit ................................................................................. 19
E
Electrical Characteristics................................................... 113 Errata .................................................................................... 3
F
FERR bit.............................................................................. 66 FSR Register........................................................... 17, 18, 27
G
General Description .............................................................. 5 GIE bit ................................................................................. 93
I
I/O Ports PORTA ........................................................................ 29 PORTB........................................................................ 31 PORTC........................................................................ 33 PORTD.................................................................. 34, 37 PORTE........................................................................ 35 Section ........................................................................ 29 I2C Addressing .................................................................. 61 Block Diagram............................................................. 60 I2C Operation .............................................................. 60 Master Mode ............................................................... 64 Mode ........................................................................... 60 Mode Selection ........................................................... 60 Multi-Master Mode ...................................................... 64 Reception .................................................................... 62 Reception Timing Diagram.......................................... 62 SCL and SDA pins ...................................................... 60 Slave Mode ................................................................. 60 Transmission............................................................... 63 I2C (SSP Module) Timing Diagram, Data ............................................... 134 Timing Diagram, START/STOP Bits.......................... 134 In-Circuit Serial Programming ....................................... 85, 98 INDF Register ......................................................... 17, 18, 27 Indirect Addressing ............................................................. 27 Instruction Cycle.................................................................. 14 Instruction Flow/Pipelining .................................................. 14 Instruction Format ............................................................... 99 Instruction Set ADDLW ..................................................................... 101 ADDWF ..................................................................... 101 ANDLW ..................................................................... 101 ANDWF ..................................................................... 101 BCF ........................................................................... 101 BSF ........................................................................... 101 BTFSC ...................................................................... 102 BTFSS ...................................................................... 102 CALL ......................................................................... 102 CLRF......................................................................... 102 CLRW........................................................................ 102 CLRWDT................................................................... 102
K
KEELOQ Evaluation and Programming Tools .................... 110
L
Loading of PC ..................................................................... 26
M
MCLR............................................................................ 87, 90 Memory Data Memory .............................................................. 15 Program Memory ........................................................ 15 Program Memory Maps PIC16C73 ........................................................... 15 PIC16C73A......................................................... 15 PIC16C74 ........................................................... 15 PIC16C74A......................................................... 15 Register File Maps PIC16C73 ........................................................... 16 PIC16C73A......................................................... 16 PIC16C74 ........................................................... 16 PIC16C74A......................................................... 16 PIC16C76 ........................................................... 16 PIC16C77 ........................................................... 16 MPLAB(R) Integrated Development Environment Software ...................................................... 107
DS30605C-page 170
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
O
OERR bit ............................................................................. 66 OPCODE ............................................................................ 99 OPTION Register ................................................................ 20 OSC Selection .................................................................... 85 Oscillator HS ......................................................................... 86, 90 LP.......................................................................... 86, 90 RC............................................................................... 86 XT ......................................................................... 86, 90 Oscillator Configurations ..................................................... 86 Output of TMR2 .................................................................. 47 RD1/PSP1 .................................................................. 13 RD2/PSP2 .................................................................. 13 RD3/PSP3 .................................................................. 13 RD4/PSP4 .................................................................. 13 RD5/PSP5 .................................................................. 13 RD6/PSP6 .................................................................. 13 RD7/PSP7 .................................................................. 13 RE0/RD/AN5 .............................................................. 13 RE1/WR/AN6.............................................................. 13 RE2/CS/AN7............................................................... 13 VDD ........................................................................11, 13 VSS ........................................................................11, 13 Pinout Descriptions PIC16C73 ................................................................... 11 PIC16C73A................................................................. 11 PIC16C74 ................................................................... 12 PIC16C74A................................................................. 12 PIC16C76 ................................................................... 11 PIC16C77 ................................................................... 12 PIR1 Register ..................................................................... 23 PIR2 Register ..................................................................... 24 POP .................................................................................... 26 POR .................................................................................... 89 Oscillator Start-up Timer (OST) ............................ 85, 89 Power Control Register (PCON)................................. 89 Power-on Reset (POR)................................... 85, 89, 91 Power-up Timer (PWRT) ............................................ 85 Power-Up-Timer (PWRT) ........................................... 89 TO............................................................................... 87 POR bit ......................................................................... 25, 89 Port RB Interrupt................................................................. 94 PORTA ............................................................................... 91 PORTA Register ........................................................... 17, 29 PORTB ............................................................................... 91 PORTB Register ........................................................... 17, 31 PORTC ............................................................................... 91 PORTC Register........................................................... 17, 33 PORTD ............................................................................... 91 PORTD Register........................................................... 17, 34 PORTE ............................................................................... 91 PORTE Register ........................................................... 17, 35 Power-down Mode (SLEEP)............................................... 97 Power-on Reset (POR) Timing Diagram ........................................................ 126 PR2 Register ................................................................ 18, 47 PRO MATE(R) II Universal Programmer ............................. 109 Product Identification System ........................................... 177 Program Memory Paging ........................................................................ 26 Program Memory Maps PIC16C73 ................................................................... 15 PIC16C73A................................................................. 15 PIC16C74 ................................................................... 15 PIC16C74A................................................................. 15 Program Verification ........................................................... 98 PS0 bit ................................................................................ 20 PS1 bit ................................................................................ 20 PS2 bit ................................................................................ 20 PSA bit................................................................................ 20 PSPMODE bit ......................................................... 34, 35, 37 PUSH.................................................................................. 26
P
P.......................................................................................... 56 Packaging ......................................................................... 153 Paging, Program Memory ................................................... 26 Parallel Slave Port ........................................................ 34, 37 Parallel Slave Port (PSP) Timing Diagram......................................................... 129 PCFG0 bit ........................................................................... 80 PCFG1 bit ........................................................................... 80 PCFG2 bit ........................................................................... 80 PCL Register........................................................... 17, 18, 26 PCLATH .............................................................................. 91 PCLATH Register ................................................... 17, 18, 26 PCON Register ............................................................. 25, 89 PD bit ............................................................................ 19, 87 PICDEMTM 1 Low Cost PICmicro Demonstration Board ........................................................ 109 PICDEMTM 2 Low Cost PIC16CXX Demonstration Board ........................................................ 109 PICDEMTM 3 Low Cost PIC16CXXX Demonstration Board ........................................................ 110 PICSTART(R) Plus Entry Level Development System ........................................................ 109 PIE1 Register ...................................................................... 22 PIE2 Register ...................................................................... 24 Pin Functions MCLR/VPP............................................................. 11, 12 OSC1/CLKIN......................................................... 11, 12 OSC2/CLKOUT..................................................... 11, 12 RA0/AN0 ............................................................... 11, 12 RA1/AN1 ............................................................... 11, 12 RA2/AN2 ............................................................... 11, 12 RA3/AN3/VREF ...................................................... 11, 12 RA4/T0CKI............................................................ 11, 12 RA5/AN4/SS ......................................................... 11, 12 RB0/INT ................................................................ 11, 12 RB1 ....................................................................... 11, 12 RB2 ....................................................................... 11, 12 RB3 ....................................................................... 11, 12 RB4 ....................................................................... 11, 12 RB5 ....................................................................... 11, 12 RB6 ....................................................................... 11, 12 RB7 ....................................................................... 11, 12 RC0/T1OSO/T1CKI .............................................. 11, 13 RC1/T1OSI/CCP2................................................. 11, 13 RC2/CCP1 ............................................................ 11, 13 RC3/SCK/SCL ...................................................... 11, 13 RC4/SDI/SDA ....................................................... 11, 13 RC5/SDO .............................................................. 11, 13 RC6/TX/CK ............................................... 11, 13, 65-76 RC7/RX/DT ............................................... 11, 13, 65-76 RD0/PSP0................................................................... 13
2000 Microchip Technology Inc.
DS30605C-page 171
PIC16C63A/65B/73B/74B
R
R/W ..................................................................................... 56 R/W bit .................................................................... 61, 62, 63 RBIF bit ......................................................................... 31, 94 RBPU bit ............................................................................. 20 RC Oscillator ................................................................. 87, 90 RCSTA Register.................................................................. 66 RD pin ................................................................................. 37 Read/Write bit Information, R/W ......................................... 56 Receive Overflow Indicator bit, SSPOV .............................. 57 Register File ........................................................................ 15 Register File Map ................................................................ 16 Registers Maps PIC16C73 ........................................................... 16 PIC16C73A ......................................................... 16 PIC16C74 ........................................................... 16 PIC16C74A ......................................................... 16 RESET Conditions ...................................................... 90 SSPSTAT .................................................................... 56 Summary..................................................................... 17 RESET .......................................................................... 85, 87 Timing Diagram......................................................... 126 RESET Conditions for Special Registers ............................ 90 Revision History ................................................................ 165 RP0 bit .......................................................................... 15, 19 RP1 bit ................................................................................ 19 RX9 bit ................................................................................ 66 RX9D bit.............................................................................. 66 SSPSTAT .................................................................... 56 SPI Clock Edge Select bit, CKE ......................................... 56 SPI Data Input Sample Phase Select bit, SMP .................. 56 SREN bit ............................................................................. 66 SSP Module Overview ........................................................ 55 Section........................................................................ 55 SSPCON .................................................................... 57 SSPSTAT .................................................................... 56 SSPADD Register............................................................... 18 SSPBUF Register ............................................................... 17 SSPCON............................................................................. 57 SSPCON Register .............................................................. 17 SSPEN................................................................................ 57 SSPM3:SSPM0 .................................................................. 57 SSPOV ......................................................................... 57, 60 SSPSTAT Register ....................................................... 18, 56 Stack................................................................................... 26 Overflows.................................................................... 26 Underflow ................................................................... 26 START bit, S....................................................................... 56 STATUS Register ............................................................... 19 STOP bit, P......................................................................... 56 Synchronous Serial Port Enable bit, SSPEN...................... 57 Synchronous Serial Port Mode Select bits, SSPM3:SSPM0 .................................................................. 57 Synchronous Serial Port Module ........................................ 55 Synchronous Serial Port Status Register ........................... 56
T
T0CS bit.............................................................................. 20 T1CKPS0 bit ....................................................................... 43 T1CKPS1 bit ....................................................................... 43 T1CON Register ................................................................. 43 T1OSCEN bit ...................................................................... 43 T1SYNC bit......................................................................... 43 T2CKPS0 bit ....................................................................... 47 T2CKPS1 bit ....................................................................... 47 T2CON Register ................................................................. 47 TAD...................................................................................... 83 Timer0 RTCC.......................................................................... 91 Timing Diagram ........................................................ 127 Timer1 Timing Diagram ........................................................ 127 Timers Timer0 External Clock .................................................... 40 Interrupt .............................................................. 39 Prescaler ............................................................ 40 Prescaler Block Diagram .................................... 39 Section................................................................ 39 T0CKI ................................................................. 40 T0IF .................................................................... 94 TMR0 Interrupt ................................................... 94 Timer1 Asynchronous Counter Mode ............................. 45 Capacitor Selection ............................................ 45 Operation in Timer Mode.................................... 44 Oscillator............................................................. 45 Prescaler ............................................................ 45 Resetting of Timer1 Registers ............................ 45 Resetting Timer1 using a CCP Trigger Output .................................................... 45 Synchronized Counter Mode .............................. 44 T1CON ............................................................... 43
S
S.......................................................................................... 56 SCL ..................................................................................... 60 Serial Communication Interface (SCI) Module, See USART Services One-Time-Programmable (OTP)................................... 7 Quick-Turnaround-Production (QTP) ............................ 7 Serialized Quick-Turnaround Production (SQTP) .......................................................................... 7 Slave Mode SCL ............................................................................. 60 SDA............................................................................. 60 SLEEP........................................................................... 85, 87 SMP .................................................................................... 56 Software Simulator (MPLAB-SIM)..................................... 108 SPBRG Register ................................................................. 18 Special Features of the CPU............................................... 85 Special Function Registers PIC16C73 ................................................................... 17 PIC16C73A ................................................................. 17 PIC16C74 ................................................................... 17 PIC16C74A ................................................................. 17 Special Function Registers, Section ................................... 16 SPEN bit.............................................................................. 66 SPI Block Diagram............................................................. 55 Master Mode Timing ................................................... 58 Serial Clock ................................................................. 55 Serial Data In .............................................................. 55 Serial Data Out............................................................ 55 Slave Mode Timing ..................................................... 59 Slave Mode Timing Diagram ....................................... 58 Slave Select ................................................................ 55 SSPCON ..................................................................... 57
DS30605C-page 172
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
TMR1H ............................................................... 45 TMR1L ................................................................ 45 Timer2 Block Diagram .................................................... 47 Module ................................................................ 47 Postscaler ........................................................... 47 Prescaler............................................................. 47 T2CON................................................................ 47 Timing Diagrams I2C Reception (7-bit Address) ..................................... 62 SPI Master Mode ........................................................ 58 SPI Slave Mode (CKE = 1) ......................................... 59 SPI Slave Mode Timing (CKE = 0).............................. 58 USART Asynchronous Master Transmission.............. 69 USART Asynchronous Reception............................... 71 USART Synchronous Reception................................. 75 USART Synchronous Transmission............................ 73 Wake-up from SLEEP via Interrupt ............................. 98 Timing Diagrams and Specifications................................. 124 A/D Conversion......................................................... 138 Brown-out Reset (BOR) ............................................ 126 Capture/Compare/PWM (CCP)................................. 128 CLKOUT and I/O....................................................... 125 External Clock........................................................... 124 I2C Bus Data ............................................................. 134 I2C Bus START/STOP Bits ....................................... 134 Oscillator Start-up Timer (OST)................................. 126 Parallel Slave Port (PSP).......................................... 129 Power-up Timer (PWRT)........................................... 126 RESET ...................................................................... 126 Timer0 and Timer1.................................................... 127 USART Synchronous Receive (Master/Slave) ......... 136 USART SynchronousTransmission (Master/Slave) .. 136 Watchdog Timer (WDT) ............................................ 126 TMR0 Register .................................................................... 17 TMR1CS bit ........................................................................ 43 TMR1H Register ................................................................. 17 TMR1L Register .................................................................. 17 TMR1ON bit ........................................................................ 43 TMR2 Register .................................................................... 17 TMR2ON bit ........................................................................ 47 TO bit .................................................................................. 19 TOUTPS0 bit....................................................................... 47 TOUTPS1 bit....................................................................... 47 TOUTPS2 bit....................................................................... 47 TOUTPS3 bit....................................................................... 47 TRISA Register ............................................................. 18, 29 TRISB Register ............................................................. 18, 31 TRISC Register ............................................................. 18, 33 TRISD Register ............................................................. 18, 34 TRISE Register ....................................................... 18, 35, 36 TXSTA Register .................................................................. 65
U
UA....................................................................................... 56 Universal Synchronous Asynchronous Receiver Transmitter (USART) .......................................................... 65 Update Address bit, UA ...................................................... 56 USART Asynchronous Mode................................................... 68 Asynchronous Receiver.............................................. 70 Asynchronous Reception............................................ 71 Asynchronous Transmitter.......................................... 68 Baud Rate Generator (BRG) ...................................... 67 Receive Block Diagram .............................................. 70 Sampling..................................................................... 67 Synchronous Master Mode......................................... 72 Timing Diagram, Synchronous Receive ........... 136 Timing Diagram, Synchronous Transmission... 136 Synchronous Master Reception ................................. 74 Synchronous Master Transmission ............................ 72 Synchronous Slave Mode........................................... 76 Synchronous Slave Reception ................................... 76 Synchronous Slave Transmit...................................... 76 Transmit Block Diagram ............................................. 68 UV Erasable Devices............................................................ 7
W
Wake-up from SLEEP......................................................... 97 Watchdog Timer (WDT).................................... 85, 87, 90, 95 Timing Diagram ........................................................ 126 WCOL ................................................................................. 57 WDT ................................................................................... 90 Block Diagram ............................................................ 96 Period ......................................................................... 95 Programming Considerations ..................................... 96 Time-out...................................................................... 91 WR pin ................................................................................ 37 Write Collision Detect bit, WCOL........................................ 57 WWW, On-Line Support ....................................................... 3
Z
Z bit..................................................................................... 19
2000 Microchip Technology Inc.
DS30605C-page 173
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 174
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
ON-LINE SUPPORT
Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site.
Systems Information and Upgrade Hot Line
The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-792-7302 for the rest of the world.
001024
Connecting to the Microchip Internet Web Site
The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: * Latest Microchip Press Releases * Technical Support Section with Frequently Asked Questions * Design Tips * Device Errata * Job Postings * Microchip Consultant Program Member Listing * Links to other useful web sites related to Microchip Products * Conferences for products, Development Systems, technical information and more * Listing of seminars and events
Trademarks: The Microchip name, logo, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, KEELOQ, SEEVAL, MPLAB and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Total Endurance, ICSP, In-Circuit Serial Programming, FilterLab, MXDEV, microID, FlexROM, fuzzyLAB, MPASM, MPLINK, MPLIB, PICDEM, ICEPIC and Migratable Memory are trademarks and SQTP is a service mark of Microchip in the U.S.A. All other trademarks mentioned herein are the property of their respective companies.
2000 Microchip Technology Inc.
DS30605C-page 175
PIC16C63A/65B/73B/74B
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: RE: Technical Publications Manager Reader Response Total Pages Sent
From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Y N FAX: (______) _________ - _________
Device: PIC16C63A/65B/73B/74B Literature Number: DS30605C Questions: 1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this data sheet easy to follow? If not, why?
4. What additions to the data sheet do you think would enhance the structure and subject?
5. What deletions from the data sheet could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
8. How would you improve our software, systems, and silicon products?
DS30605C-page 176
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. Device -XX X /XX Package XXX Pattern
Examples:
Frequency Temperature Range Range
a)
b)
Device
PIC16C6X(1), PIC16C6XT(2); VDD range 4.0V to PIC16LC6X(1), PIC16LC6XT(2); VDD range 2.5V PIC16C7X(1), PIC16C7XT(2); VDD range 4.0V to (2) PIC16LC7X(1)
5.5V to 5.5V 5.5V , PIC16LC7XT ; VDD range 2.5V to 5.5V
c)
PIC16C74B -04/P 301 = Commercial temp., PDIP package, 4 MHz, normal VDD limits, QTP pattern #301. PIC16LC63A - 04I/SO = Industrial temp., SOIC package, 200 kHz, Extended VDD limits. PIC16C65B - 20I/P = Industrial temp., PDIP package, 20 MHz, normal VDD limits.
Frequency Range
04 20
= 4 MHz = 20 MHz
Note 1: 2:
C LC T
Temperature Range
blank I E
= 0C to 70C = -40C to +85C = -40C to +125C
(Commercial) (Industrial) (Extended)
= CMOS = Low Power CMOS = in tape and reel - SOIC, SSOP, PLCC, QFP, TQ and FP packages only.
Package
JW PQ PT SO SP P L SS
= = = = = = = =
Windowed CERDIP MQFP (Metric PQFP) TQFP (Thin Quad Flatpack) SOIC Skinny plastic dip PDIP PLCC SSOP
Pattern
QTP, SQTP, Code or Special Requirements (blank otherwise)
* JW Devices are UV erasable and can be programmed to any device configuration. JW Devices meet the electrical requirement of each oscillator type (including LC devices).
Sales and Support
Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
2000 Microchip Technology Inc.
DS30605C-page 177
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 178
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
NOTES:
2000 Microchip Technology Inc.
DS30605C-page 179
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 180
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
NOTES:
2000 Microchip Technology Inc.
DS30605C-page 181
PIC16C63A/65B/73B/74B
NOTES:
DS30605C-page 182
2000 Microchip Technology Inc.
PIC16C63A/65B/73B/74B
NOTES:
2000 Microchip Technology Inc.
DS30605C-page 183
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com
ASIA/PACIFIC
China - Beijing
Microchip Technology Beijing Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104
ASIA/PACIFIC (continued)
Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850
Rocky Mountain
2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456
Taiwan
Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
China - Shanghai
Microchip Technology Shanghai Office Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060
Atlanta
500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
EUROPE
Denmark
Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910
Boston
2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821
Hong Kong
Microchip Asia Pacific RM 2101, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431
Chicago
333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
India
Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062
France
Arizona Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Dallas
4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924
Dayton
Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175
Germany
Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Japan
Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122
Detroit
Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260
Italy
Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934
Los Angeles
18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338
United Kingdom
Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820
10/01/00
New York
150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335
San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955
Toronto
6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509
Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified.
All rights reserved. (c) 2000 Microchip Technology Incorporated. Printed in the USA. 12/00
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
DS30605C-page 184
2000 Microchip Technology Inc.

▲Up To Search▲

Price & Availability of PIC16C74B-04L

	To Download PIC16C74B-04L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .