View CT028TN03_166154.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
INNOLUX DISPLAY CORPORATION
LCD MODULE
SPECIFICATION
Customer: Model Name: Spec. No.: Date: Version: CT028TN03 (Puma-T1) C028-03-TT-01 2008/01/02 1.0
Preliminary Specification Final Specification
For Customer's Acceptance
Approved by
Comment
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Record of Revision Version Revise Date 1.0 2008/01/02 Page All Initial release Content
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Contents
1. 2. 3. 4. General Specifications........................................................................................................... 1 Block Diagram ....................................................................................................................... 2 Pin Assignments.................................................................................................................... 3 Electrical Specifications ......................................................................................................... 5 4.1. 4.2. 4.3. 4.4. 4.5. 4.6. 5. 5.1. 5.2. 5.3. 5.4. 5.5. 6. 7. 8. Absolute Maximum Rating.......................................................................................... 5 Typical Operation Conditions ...................................................................................... 5 Backlight Unit.............................................................................................................. 7 Instruction Setting Flow .............................................................................................. 8 Display RAM Data Format and Input Bus ................................................................. 10 Timing Characteristic .............................................................................................. 10 Electrical Characteristic .......................................................................................... 12 Optical Characteristic .............................................................................................. 12 Mechanical Characterist ......................................................................................... 12 Touch Panel Circuit Block ....................................................................................... 14 Proposal of Mobile Phone Design............................................................................. 15
Touch Panel Specifications ................................................................................................. 12
Optical Specifications .......................................................................................................... 16 Reliability Test Items............................................................................................................ 21 Handling Precautions .......................................................................................................... 22 8.1. 8.2. 8.3. 8.4. 8.5. Safety ....................................................................................................................... 22 Handling ................................................................................................................... 22 Static Electricity......................................................................................................... 22 Storage ..................................................................................................................... 22 Cleaning ................................................................................................................... 22
9.
Mechanical Drawing ............................................................................................................ 23 10.1. 10.2. 10.3. Packing Material Per Carton .................................................................................... 24 Packing Specification and Quantity.......................................................................... 24 Illustration ................................................................................................................ 24
10. Package Drawing ................................................................................................................ 24
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 1/24
1. General Specifications
1.1 Description
The CT028TN03 is a color active matrix Thin Film Transistor (TFT) Liquid Crystal Display (LCD) that uses amorphous silicon (a-Si) TFT as a switching device. This model is composed of a single 2.8 inches transmissive type main TFT-LCD panel and a resistive touch screen display. The resolution of the panel is 240x320 pixels and can display up to 65K/262K color.
1.2
Features
-TM type for main TFT-LCD panel -Resistive type touch panel -One backlight with 4 white LEDs -80-system 18/16/8-bit parallel bus -Full, Still, Partial & Standby modes are available
1.3 1.4
No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Application General Specification
Item LCD Size Panel Type Touch Panel Type Resolution Display Mode Display Number of Colors Viewing Direction Contrast Ratio Luminance Module Size Panel Active Area Touch Panel Active Area Touch Panel View Area Pixel Pitch Weight Driver IC Driver IC RAM Size Light Source Interface Operating Temperature Storage Temperature Specification 2.83 a-Si TFT active matrix 4-wire Analog Resistive 240 x RGB x 320 Normally white, Transmissive 65K/262K 12 o'clock 500 250 50.20(W) x 69.30(L) x 3.65 (T) 43.20(W) x 57.60(L) 44.20(W) x 62.50(L) 44.80(W) x 63.10(L) 0.180(W) x 0.180(L) TBD HX8347 240 x 18 x 320 4 white LEDs in Parallel 80-system 18/16/8-bit parallel bus -20~70 -30~80 Unit inch pixel cd/m2 mm mm mm mm mm 9 bit Remark Note 1 Note 2 Note 1 Note 1 Note 1 Note 1 -
-Display terminals for cellular phone
Note 1: Please refer to the mechanical drawing. Note 2: Luminance is measured with touch panel attached.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 2/24
2. Block Diagram
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 3/24
3. Pin Assignments
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 Symbol FLM GND YB XR YT XL GND IF0 IF1 VDD VDD VDD NC D17 D16 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 I/O O P P I I P P P I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O Function Connect to TE(Tearing Effect) Pin Ground Touch panel signal Touch panel signal Touch panel signal Touch panel signal Ground Interface select signal Interface select signal Analog/Logic supply voltage Analog/Logic supply voltage Analog/Logic supply voltage Dummy Pin Data bus (Bit 17) Data bus (Bit 16) Data bus (Bit 15) Data bus (Bit 14) Data bus (Bit 13) Data bus (Bit 12) Data bus (Bit 11) Data bus (Bit 10) Data bus (Bit 9) Data bus (Bit 8) Data bus (Bit 7) Data bus (Bit 6) Data bus (Bit 5) Data bus (Bit 4) Data bus (Bit 3) Data bus (Bit 2) Remark Note 2 Note 2 Note 1 Note 1 Note 1 -
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 4/24
D1 D0 NRES NRD NWR RS NCS GND LED1+ LED2+ LED3+ LED4+ NC NC LEDID I/O I/O I I I I I P O Data bus (Bit 1) Data bus (Bit 0) Reset signal (Low: active) Read signal (Low: active) Write signal (Low: active) Register select signal Chip select signal (Low: active) Ground LED anode LED anode LED anode LED anode Dummy Pin Dummy Pin LED cathode Connect to VDD by a 120K resister -
30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45
Note 1: There is only one power VDD input to combine digital power and analog power. Note 2: Interface Selection IF0 IF1 0 0 1 0 1 1 Bus Width 16-bit parallel 18-bit parallel 8-bit parallel Bit Number in a pixel 16-bit (65K) 18-bit (262K) 18-bit (262K) Data Bus D15~D0 D17~D0 D7~D0
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 5/24
4. Electrical Specifications
4.1 Absolute Maximum Rating
(Ta=+25) Item TFT Module Backlight Unit Analog/Logic Supply Voltage Current Power Consumption Symbol VDD IB PBL Values Min. -0.3 Max. +4.6 120 480 V mA mW Note 1 Note 2 Note 2 Unit Remark
Note1: Permanent damage to the device may occur if maximum values are exceeded or reverse voltage is applied. Note2: Without LED driver IC, please refer to 4.3.
4.2
Typical Operation Conditions
(Ta=+25) Item Symbol Min. VDD VIH VIL VOL VOH fFRAME 2.7 0.8 VDD 0 0 0.8 VDD Values Typ. 2.8 80 Max. 3.0 VDD 0.2VDD 0.2VDD VDD V V V V V Hz Note Unit Remark
4.2.1 DC Characteristics
Analog/ Logic Supply Voltage Input High Voltage Input Low Voltage Output Low Voltage Output High Voltage Frame Frequency
Note: To prevent IC latch up or DC operation in LCD panel, the power on/off sequence should follow the driver IC specification.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 6/24
Values Typ. Max.
4.2.2 Current Consumption
Item Symbol Unit Remark
MCU Interface (80-system 18/16/8-bit parallel bus) Still Mode Standby Mode Note1: Test Condition Typ: VDD=2.8V Display Pattern: 8 Color Bar Frame Rate=80Hz at Line Inversion Operating Temperature: 25 Typ. current check pattern: Max: VDD=3.0V Display Pattern: All Pixel Black Frame Rate=80Hz at Line Inversion Operating Temperature: 25 Max. current check pattern: VDD VDD TBD TBD TBD TBD mA uA Note1 Note1, Note2
8-Color Bar
Black
Note2: In the standby mode, all the internal display operations are suspended including the internal R-C oscillator.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 7/24
4.3
Backlight Unit
VBL
LED-
The backlight system is an edge lighting type with 4 white LEDs.
IB
ILED
LED1+ LED2+ LED3+ LED4+
(Ta=+25) Item Current Power Consumption Symbol Min. IB PBL Values Typ. 80 270 Max. mA mW Note 1 Note 2 Unit Remark
Note1: 4 LEDs are connected in parallel; each LED's current consumption is 20mA. Note2: Where IB= 80mA, PBL = IB x VBL, VBL is backlight forward voltage.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 8/24
4.4
Instruction Setting Flow
4.4.1 Initial Setting Sequence TBD 4.4.2. Standby In/Out Sequence TBD
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 9/24
4.5
Display RAM Data Format and Input Bus
4.5.1 18-bit Parallel Bus System Interface
4.5.2 16-bit Parallel Bus System Interface
4.5.3 8-bit Parallel Bus System Interface
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 10/24
tCHW
VIH tCSF VIL tRCSFM VIH VIL tAST tAHT tWC tCS tCSH tWRL VIH VIL tRCFM VIH VIH tRDHFM tDST VIH tDHT VIL tRATFM VOH VOL tRDLFM VIH VIL tODH VOH VOL tWRH tAHT tCSF VIH VIL VIH VIL
4.6
NCS
Timing Characteristic
tCHW
4.6.1 Parallel Interface Characteristics (8080-series MPU)
RS
NWR
VIH VIL
NRD
VIL
D17~D0
VIL
Signal RS
NCS
NWR
NRD
D0 to D17
Symbol tAST tAHT tCHW tCS tRCSFM tCSF tCSH tWC tWRH tWRL tRCFM tRDHFM tRDLFM tDST tDHT tRATFM tODH
Parameter Min. Address setup time 10 Address hold time (Write/Read) 10 Chip select "H" pulse width 0 Chip select setup time (Write) 35 Chip select setup time 180 Chip select wait time (Write/Read) 10 Chip select hold time 10 Write cycle 100 Control pulse "H" duration 15 Control pulse "L" duration 20 Read cycle 250 Control pulse "H" duration 15 Control pulse "L" duration 180 Data setup time 10 Data hold time 10 Read access time Output disable time 20
Max . 180 80
(VDD=2.7 to 3.0V, Ta=25) Unit Description ns -
ns
-
ns
-
ns
When read from GRAM
ns
For maximum CL=30pF For minimum CL=8pF
Note: The input signal rise time and fall time (tr, tf) is specified at 15ns or less. Logic high and low levels are specified as 30% and 70% of VDD for input signals.
Input Signal Slope Output Signal Slope
tr
VIH=0.7*VDD VIL =0.3*VDD
tf
tr
VOH =0.8*VDD VOL =0.2*VDD
tf
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 11/24
4.6.2 Reset Input Timing
0.8*VDD VDD NRES
tPRES
Shorter than 5us
tRESW tREST
Internal Status
Normal Operation
Resetting
Initial Condition (Default for H/W reset)
Symbol tRESW tREST
Parameter Reset low pulse width(1) Reset complete time(2)
Related Pins Min. NRES 10 -
Typ. -
Max. 5 120
Note When reset applied during STB mode
Unit s ms
When reset applied ms during STB mode Reset goes high level Reset goes high level tPRES NRES &VDD 1 ms after Power on time after Power on Note: (1) Spike due to an electrostatic discharge on NRES line does not cause irregular system reset according to the table below. NRES Pulse Action Shorter than 5s Longer than 10s Between 5s and 10s Reset Rejected Reset Reset Start
(2) During the resetting period, the display will be blanked (The display is entering blanking sequence, which maximum time is 120 ms, when Reset Starts in STB Out-mode, the display remains the blank state in STB-mode) and then return to Default condition for H/W reset. (3) During Reset Complete Time, ID2 and VCOMOF value in OTP will be latched to internal register during this period. This loading is done every time when there is H/W reset complete time (tREST) within 5ms after a rising edge of NRES. (4) Spike Rejection also applies during a valid reset pulse as shown below:
10us
Reset is accepted 10us
1us
Less than 1usec width positive spike will be rejected.
(5) It is necessary to wait 5msec after releasing NRES before sending commands. Also STB Out command cannot be sent for 120msec.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 12/24
5 Touch Panel Specifications
5.1 Electrical Characteristics
Item Min. Linearity Terminal Resistance Insulation resistance Operating Voltage -1.5 180 270 25 Value Typ. 5 Max. 1.5 560 760 % M V Note 3 X Y DC 25V DC Unit Remark
5.2
Optical Characteristics
Item Min. Value Typ. Max. 10 ms % 100k pull-up Unit Remark
Response Time Light Transparency
80
5.3
Mechanical Characteristics
Item Min. Value Typ. Max. 80 gf H time time Note 1 Note 2, 4 Note 2, 5 Unit Remark
Active Force Surface Hardness Pen Sliding Durability Hitting Durability
3 100,000 1,000,000
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 13/24
Note 1: Do not operate it with a stylus other than a polyacetal pen (tip R0.8mm or less) or a finger, especially those with hard or sharp tips such as a ball point pen or a mechanical pencil. Note 2: Test Condition: End shape: R0.8mm and R8.0mm, Resistance between X and Y axis must be equal or lower than 2K, the test voltage =DC5V. Note 3: Measurement For Linearity. (After environment and life test) -Load: 150g with End shape R0.8 mm Polyacetal resin. -Measuring area: 1.0mm inside the edge of touch panel active area, pitch 5mm. (Fig. 1)
1mm 1mm TP Outline TP A/A Test boundary 5mm 1mm
Fig. 1 Measuring area for Linearity Note 4: Measurement for surface area. -Scratch 100,000 times of straight line on the screen with a stylus which is changed every 20,000 times. One time is defined in one direction, strike one time, and then in the reverse direction strike one time that defined 2nd time. -Force: 150gf. -Speed: 150mm/sec. -Writing Length: 35mm. -Stylus: R0.8 polyacetal tip. -Measuring area: 2.0mm inside the edge of touch panel active area, any line. (Fig. 2) -Result: the SPEC of Electrical Characteristics pass. Note 5: Hit 1,000,000 times on the screen with a R0.8mm Polyacetal resin By stylus tapping at same points. -Force: 250gf. -Speed: 5times/sec. -Measuring area: 2.0mm inside the edge of touch panel active area, any point. (Fig. 2) -Result: The SPEC of Electrical Characteristics pass.
2mm 2mm TP Outline TP A/A Test boundary 2mm
Fig. 2 Measuring area for Pen Sliding & Hitting Durability
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
2mm
TP Outline TP A/A Test boundary
1mm
TP Outline TP A/A Test boundary 5mm
www..com
Spec. No.: C028-03-TT-01 Page: 14/24
5.4
Touch Panel Circuit Block
YT XL YB XR
YT XL YB XR
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 15/24
5.5
Proposal of Mobile Phone Design
Note 1:"Top enclosure" is the top case of mobile phone. Note 2:"Window Area" is the opening area of top enclosure of the mobile phone, we suggest customers design it following the drawing and there should be no defect in the LCD module within the area. Note 3:"Cushion Area" is the cushion customer use between top enclosure and LCM, we suggest customers design it following the drawing and the cushion should not press the TP V/A.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 16/24
6 Optical Specifications
(Ta=+25, VDD=+2.8V, IB=80mA) Item Left Viewing Angle Range Right Top Bottom Response Time Contrast Ratio Luminance White Color Chromaticity (CIE1931) Red Green Blue Color Gamut Luminance Uniformity Flicker Crosstalk Symbol L R T B Ton +Toff CR L Wx Wy Rx Ry Gx Gy Bx By NTSC UL Normal ==0 Normal ==0 Normal ==0 CR10 Condition Min. 350 75 Values Typ. 65 65 65 55 25 500 250 0.28 0.29 0.59 0.34 0.34 0.58 0.14 0.06 55 80 No Visible No Visible Max. ms cd/m2 Note 2,3 Note 2,4 Note 2,5 degree Note 1,2 Unit Remark
Normal ==0
-
Note 2,6
CIE1931 Normal ==0 -
% % -
Note 2,7 Note 8 Note 9
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 17/24
Note 1: Definition of viewing angle range Normal line ==0 T B L R
12 o'clock direction =90
=180
=0
Active Area LCD Panel
=270 6 o'clock direction
Fig. 1 Definition of viewing angle
Top
Left
Right
Bottom
Fig. 2 Definition of viewing angle for display
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 18/24
Note 2: Definition of optical measurement system The optical characteristics should be measured in a dark room with ambient temperature Ta=+25. The optical properties are measured at the center point of the LCD screen after 5 minutes operation. (Equipment: Photo detector TOPCON BM-5A or BM-7 /Field of view: 1 /Height: 500mm.)
Photo detector
Normal line ==0
500mm
12 o'clock direction =90
=180
=0
Active Area LCD Panel
=270 6 o'clock direction
Fig. 3 Optical measurement system setup Note 3: Definition of response time The response time is defined as the LCD optical switching time interval between "White" state and "Black" state. Rise time (Ton) is the time between photo detector output intensity changed from 90% to 10%, and fall time (Toff) is the time between photo detector output intensity changed from 10% to 90%.
White (TFT OFF)
Photo detector output (Relative value) 100% 90%
Black (TFT ON)
White (TFT OFF)
10% 0% Ton Fig. 4 Definition of response time Toff
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 19/24
Luminance measured when LCD on the " White" state Luminance measured when LCD on the " Black" state
"white" state.
Note 4: Definition of contrast ratio
Contrast ratio (CR) =
Note 5: Definition of luminance
Measured at the center area of the panel when LCD panel is driven at Note 6: Definition of color chromaticity (CIE1931)
Color coordinates measured at the center point of LCD when panel is driven at "White", "Red", "Green" and "Blue" state respectively. Note 7: Definition of luminance uniformity To test for uniformity, the tested area is divided into 3 rows and 3 columns. The measurement spot is placed at the center of each circle as below.
Luminance Uniformity (UL) =
L-------Active area length W----- Active area width
W W/6 W/3 W/3
L min L max
L
Fig. 5 Definition of luminance uniformity
L max : The measured maximum luminance of all measurement position.
L min : The measured minimum luminance of all measurement position.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
L/3
L/3
L/6
www..com
Spec. No.: C028-03-TT-01 Page: 20/24
Note 8: Definition of Flicker Flicker is the pattern usually used to describe the visual sensation produced by a rapidly varying light intensity. There should be no visible flicker in normal direction of the display when the following figure is loaded.
Fig.6 Flicker checker pattern
Note9: Definition of crosstalk There should be no visible in normal direction of the display when the following figures are loaded.
Fig.7 Crosstalk checker pattern
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 21/24
7 Reliability Test Items
Test Items High Temperature Storage Low Temperature Storage High Temperature Operation Low Temperature Operation High Temperature and Humidity Operation Thermal Shock Test Conditions +803 for 240 hours -303 for 240 hours +703 for 240 hours -203 for 240 hours +603, 90%3%RH max. for 240 hours -30/0.5h ~ +80/0.5h for a total 100 cycles, Start with cold temp and end with high temp Frequency range:10~55Hz Stoke:1.5mm Sweep:10Hz~55Hz~10Hz 2 hours for each direction of X. Y. Z. (6 hours for total) 100G 6ms,X, Y, Z 3 times for each direction Random Vibration : 0.015G2/Hz from 5-200Hz, -6dB/Octave from 200-500Hz 1 hour for each direction of X. Y. Z. (3 hours for total) Height :72cm(Weight10kg); 60cm(Weight>10kg) 1 corner, 3 edges, 6 surfaces 2KV, Human Body Mode, 100pF/1500 Remark -
Vibration Test
-
Mechanical Shock
-
Package Vibration Test
-
Package Drop Test Electro Static Discharge
-
Note1: During the display practical test under normal operation condition, there shall be not change or effect to the display function. Note2: Before function check, the test sample requires 2 hours storage at room temperature. Before test the function of TP, the sample must be placed in room temperature for 24hrs after RA test.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 22/24
8 Handling Precautions
8.1. 8.1.1 8.2. Safety The liquid crystal in the LCD is poisonous. DO NOT put it in your mouth. If the liquid crystal touches your skin or clothes, wash it off immediately using soap and water. Handling
8.2.1 The LCD and touch panel is made of plate glass. DO NOT subject the panel to mechanical shock or to excessive force on its surface. 8.2.2 Do not handle the product by holding the flexible pattern portion in order to assure the reliability 8.2.3 Transparency is an important factor for the touch panel. Please wear clear finger sacks, gloves and mask to protect the touch panel from finger print or stain and also hold the portion outside the view area when handling the touch panel. 8.2.4 Provide a space so that the panel does not come into contact with other components. 8.2.5 To protect the product from external force, put a covering lens (acrylic board or similar board) and keep an appropriate gap between them. 8.2.6 Transparent electrodes may be disconnected if the panel is used under environmental conditions where dew condensation occurs. 8.2.7 Property of semiconductor devices may be affected when they are exposed to light, possibly resulting in IC malfunctions. 8.2.8 To prevent such IC malfunctions, your design and mounting layout shall be done in the way that the IC is not exposed to light in actual use. 8.3. Static Electricity 8.3.1 Ground soldering iron tips, tools and testers when they are in operation. 8.3.2 Ground your body when handling the products. 8.3.3 Power on the LCD module BEFORE applying the voltage to the input terminals. 8.3.4 DO NOT apply voltage which exceeds the absolute maximum rating. 8.3.5 Store the products in an anti-electrostatic bag or container. 8.4. Storage 8.4.1 Store the products in a dark place at +2510 with low humidity (65%RH or less). 8.4.2 DO NOT store the products in an atmosphere containing organic solvents or corrosive gas. 8.5. Cleaning 8.5.1 DO NOT wipe the touch panel with dry cloth, as it may cause scratch. 8.5.2 Wipe off the stain on the product by using soft cloth moistened with ethanol. DO Not allow ethanol to get in between the upper film and the bottom glass. It may cause peeling issue or defective operation. Do not use any organic solvent or detergent other than ethanol.
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 23/24
9 Mechanical Drawing
The copyright belongs to InnoLux. Any unauthorized use is prohibited.
www..com
Spec. No.: C028-03-TT-01 Page: 24/24
10. Package Drawing
10.1. Packing Material Per Carton TBD 10.2. Packing Specification and Quantity TBD 10.3. Illustration TBD
The copyright belongs to InnoLux. Any unauthorized use is prohibited.

▲Up To Search▲

Price & Availability of CT028TN03

	To Download CT028TN03 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .